烤面包机

烤面包机维修指南解决烤面包机无法加热的问题烤面包机维修指南：解决烤面包机无法加热的问题烤面包机作为现代家庭中常见的厨房电器之一，为人们提供了方便快捷的早餐选择。

然而，当我们使用烤面包机时，有时会遇到无法加热的问题，这给我们的早餐制备带来了困扰。

本篇文章将为大家提供一份烤面包机维修指南，帮助您解决烤面包机无法加热的问题。

一、外部检查首先，当我们发现烤面包机无法加热时，应该进行外部检查。

确保电源线插座正常插入，并且插座本身没有问题。

同时，检查烤面包机的开关是否处于打开状态。

如果以上两项都没有问题，我们可以进一步检查烤面包机的电源线是否受损。

如果发现电源线有明显的磨损、折断或者外露的情况，应该立即更换电源线，以确保安全使用。

二、内部元件检查如果外部检查未发现问题，接下来我们需要进行内部元件的检查。

首先，我们需要关闭烤面包机并拔掉电源插头。

然后，使用螺丝刀将烤面包机的外壳打开，以便我们能够进一步检查内部元件的情况。

在检查内部元件之前，我们应该确保自己有一定的电器知识和相应的安全措施。

如果您对此不熟悉或者不确定，请寻求专业人士的帮助来进行维修。

在打开烤面包机外壳后，我们可以首先检查加热元件。

加热元件是烤面包机能够加热的关键元件，它通常位于烤面包机的顶部和底部。

如果发现加热元件出现明显的断裂、烧毁或者腐蚀的情况，那么很有可能是加热元件故障导致无法加热。

除了加热元件，还应该检查控温器或者热保护装置。

这些元件常常位于烤面包机的内壁上，用于控制加热温度并保护烤面包机避免过热。

三、维修方法在确认了烤面包机无法加热的原因后，我们可以根据具体的故障情况采取不同的维修方法。

如果加热元件出现断裂或烧毁的情况，我们需要将其更换为新的加热元件。

可以通过与烤面包机品牌厂家联系购买原装配件，或者请专业维修人员进行更换。

如果控温器或者热保护装置故障，我们同样需要将其更换。

同样地，要采购适配的替换件，并寻求专业人士的帮助进行更换。

值得一提的是，在进行维修前，我们应该先将烤面包机断电，并且在拆卸和更换元件时严格按照操作指南进行，以确保自己的安全和维修的有效性。

烤面包机维修要点修复烤面包机出现的加热不均匀或无法弹起的故障在烹饪早餐的常用工具中，烤面包机无疑是一款非常实用的厨房电器。

然而，由于使用频繁和长时间的使用，烤面包机也可能会出现一些故障，比如加热不均匀或无法弹起等问题。

本文将重点介绍烤面包机维修的要点，并提供解决这些故障的方法。

一、加热不均匀的故障修复加热不均匀是烤面包机常见的问题之一，如果不及时修复，会导致面包烤制不均匀、外焦里嫩，影响口感。

以下是几种常见的加热不均匀故障及其解决方法：1. 老旧加热管：在长时间使用后，加热管可能会老化或出现不均匀的加热情况。

解决方法是更换均匀加热的加热管。

2. 面包间距不均匀：若面包放入的间距不一致，也会导致烤制不均匀。

解决方法是在放入面包时保持合适的间距，确保热量可以均匀散发。

3. 中央加热过度：有些烤面包机设计加热管位于中央位置，容易导致中央部分的面包烤制过度。

解决方法是在烘烤过程中适当调整面包的位置，使热量分布更加均匀。

二、无法弹起的故障修复无法弹起是烤面包机的另一个常见故障，如果遇到这个问题，面包在烘烤结束后将无法自动弹起，需要手动取出。

以下是几种常见的无法弹起故障及其解决方法：1. 过烤导致卡住：烤面包时间过长，面包可能会因此粘在烤盘上，导致无法弹起。

解决方法是在烤制时控制好时间，避免过度烘烤。

2. 弹簧失灵：烤面包机内部有一个弹簧装置，用于控制面包的弹起与下落。

如果弹簧损坏或松弛，将导致无法弹起。

解决方法是更换弹簧或调整弹簧的紧度。

3. 按钮卡住：烤面包机的按钮或开关可能会因为积累了面包屑或其他杂物而卡住，导致无法弹起。

解决方法是清理按钮周围的杂物，并确保按钮的灵活性。

总结：烤面包机作为一种常用的厨房电器，出现故障是难以避免的。

然而，只要遵循正确的修复要点，我们能够轻松解决烤面包机的加热不均匀和无法弹起等故障。

在维修中，我们要根据具体故障的原因，采取相应的修复方法，包括更换老化的加热管、调整面包间距、适当调整面包的位置、控制烤制时间、更换损坏的弹簧以及清理按钮周围的杂物等。

烤面包机不工作检查和修理随着现代生活的快节奏，烤面包机已成为许多家庭必备的小家电之一。

然而，有时候我们可能会遇到烤面包机不工作的情况。

本文将为您介绍一些常见的烤面包机故障，并提供检查和修理的方法。

一、烤面包机不加热1. 确认插座正常工作。

首先，检查插座是否正常供电。

可以将其他家电插到相同的插座上测试。

如果其他家电正常工作，则问题可能出在烤面包机上。

2. 检查供电线是否损坏。

检查电源线是否有明显的损坏，如断裂、破损等。

如果有损坏，请联系专业维修人员进行更换。

3. 清理加热元件。

有时候加热元件可能会被食物残渣覆盖，导致加热不均匀。

将烤面包机放置在通风的地方，使用软布清理加热元件。

二、烤面包机无法弹出1. 检查弹簧是否失灵。

打开烤面包机底部的接口，查看弹簧是否松动或断裂。

如果发现问题，请联系售后服务进行修理。

2. 清理面包屑。

经常清理烤面包机底部的面包屑收集器，以防止面包屑堆积导致无法弹出。

使用软刷或吹风机将面包屑清理干净。

三、烤面包机底部糊黑1. 清理底部碳化物。

长时间使用后，烤面包机底部可能会出现积碳现象。

使用软布蘸取少量醋或香蕉去除剂，轻轻擦拭底部碳化物。

2. 调整烤面包机高度。

如果烤面包片过于靠近加热元件，会导致烤出的面包糊黑。

调整烤面包机的高度，确保面包与加热元件的距离适当。

四、烤面包机按钮无法操作1. 清理按钮周围的食物残渣。

不时清理烤面包机的按钮及其周围的食物残渣，以确保按钮可以正常操作。

2. 检查按钮弹簧是否松动或断裂。

如果按钮弹簧失灵，可以联系售后服务进行维修或更换。

总结：烤面包机是我们日常生活中重要的厨房电器之一，但偶尔会遇到一些故障。

本文提供了烤面包机常见故障的解决方法，包括检查插座、供电线、清理加热元件、检查弹簧、清理面包屑、清理底部碳化物等。

希望这些方法能帮助您解决烤面包机的问题，保证其正常工作。

如果以上方法无法解决问题，建议您联系专业的维修人员进行检修和修理。

祝您早日恢复烤面包机的使用！。

如何正确使用烤面包机的教程烤面包机是现代家庭中常见的厨房电器之一，它能够方便快捷地烘烤面包片，不仅省时省力，而且制作出的面包味道更加香脆美味。

为了正确使用烤面包机，下面将为您介绍一些简单实用的使用技巧和注意事项。

一、准备工作在使用烤面包机之前，首先需要确保清洁干净。

请将插头拔下并且冷却机器，然后使用温和的清洁剂和柔软的海绵清洁设备的内部和外部。

切勿将烤面包机的内部零部件浸入水中清洗。

接下来，将烤面包机的碗盖打开，清除和清洁面包屑收集盒的残渣。

现在，您可以开始使用烤面包机了。

二、选择面包片与配料首先，选择适合的面包片放入面包机中。

可以根据个人口味选择全麦面包、白面包、多谷物面包等。

需要注意的是，面包片的厚度应适中，太厚可能无法完全受热，太薄则会导致过度烘烤。

其次，根据个人喜好准备配料，如黄油、花生酱、果酱、奶酪等。

配料的选择将直接影响到口感和口味。

三、设置烤面包机接下来，按照烤面包机上的操作按钮设置所需的参数。

一般来说，烤面包机上会有时间、温度和烤度等调节选项。

根据面包片的厚度和喜好，应当适当调节这些参数。

较薄的面包片可以选择较低的温度和烤度，而较厚的面包片则需要较高的温度和烤度。

对于初次使用烤面包机的人来说，建议先选择较低的温度和烤度，以免烘烤过度。

四、开始烤制面包片在调节好烤面包机的参数后，将面包片放入烤面包机的夹层中，然后关闭碗盖。

根据烤面包机的具体型号，有的烤面包机需要按下“开始”按钮，有的则自动启动。

等待烤面包机完成烘烤的过程，期间可以闻到香气和听到轻微的嗒嗒声，这是正常现象。

请勿在烘烤过程中打开烤面包机的碗盖，以免影响烤制效果。

五、取出烤好的面包片当烤面包机提示烤制完成或者时间到达时，可以小心打开烤面包机的碗盖，使用抓取工具取出烤好的面包片。

请注意，烤面包机内的温度很高，应当避免直接用手触摸。

将烤好的面包片放置于烤面包机旁的架子上，稍作冷却，然后便可享用美味的面包早餐了。

六、清洁烤面包机在使用完烤面包机后，务必记得将插头拔下，并等待其冷却。

toaster用法
Toaster（烤面包机）在生活中是一款很常见的电器，每个家庭都或多或少会有一台。

它可以帮助我们在清晨或者下午茶时间轻松制作出香脆的面包，但是很多人没有完全学会如何使用烤面包机来制作更加美味、赏心悦目的面包。

今天就让我们来一步步了解如何使用这款电器吧。

1.准备
在使用烤面包机之前，我们需要将它清洁干净并放置在平稳的表面上。

接下来将插头插入电源插座，等待烤面包机预热。

2.选择面包
将面包放在一个干净的砧板上，可以选择白面包、全麦面包、黄油面包等等。

如果需要切片，可以用切面包刀将面包切成适当的大小和形状。

3.涂抹黄油或果酱
涂抹适当的黄油或果酱在面包片上，可以增加面包的口感和风味。

4.放入烤面包机
将涂抹了黄油或果酱的面包放入烤面包机的插槽中，注意面包片不能比插槽更高。

在放入面包的同时，我们还需要确定烤面包的时间和温度，通常在烤面包机上都有相关的指示。

5.烤完后取出面包
当烤面包机提示烤完了，或者预设的时间到了，我们需要将面包取出来。

用烤面包机自带的托盘或手套，取出面包片，然后用切面包刀将面包切成适当的大小，从而更好地享用。

需要注意的是，当我们在使用烤面包机时，不要离开去做别的事情。

确保我们留在旁边，以防止面包在烤的过程中超时烤焦。

如果烤焦了，面包就不能再吃了。

总之，烤面包机在制作面包时，帮助我们节省了时间和精力。

只需几个简单的步骤，我们就能够制作出自己喜欢的面包，并且可以根
据口味添加不同的食材。

所以，在学会如何使用后，希望能够多加利用这款电器，让我们享受到更加美味的早餐或下午茶时间。

Daily Collection 8 档外形小巧内置面包烘烤架HD2519/60香脆金黄吐司从此每日尽享8 档烘烤程度自由选择，内置烘烤架这款烤面包机精致小巧，独含 8 档烘烤控制级别，以及 2 个可变加宽烘烤槽，为你提供均匀烘烤的焦黄效果，适用于各式各样的面包类型。

内置烘烤架使你能够轻松加热你所爱的花式面包、糕点和小圆面包。

易于使用一键即可加热、解冻可分离式面包屑底盘，方便清洁提升功能可轻松取出小块面包取消按钮，可即时关闭均匀的烘烤效果8 档烘烤控制级别，可根据个人喜好选择2 个可变加宽烘烤槽，适用于不同类型的面包内置烘烤架，适用于加热花式面包、糕点或小圆面包安全且卫生附加自动关闭防护功能产品亮点2个可变加宽烘烤槽2 个可变加宽烘烤槽，适用于不同类型的面包。

得益于面包置中功能，每一片面包都能保持并锁定在居中位置，使两侧均可以均匀地进行烘烤，从而获得完美的焦黄效果。

8档烘烤控制级别8 档烘烤控制级别，让您可以烘烤不同类型的面包，同时避免烤焦困扰。

根据您个人喜好调节的烘烤级别，一定能让您烤出满意的面包。

提升功能提升功能可轻松取出小块面包。

一键即可加热、解冻再加热功能可于数秒内加热面包，解冻功能可一键快捷烘烤冷冻面包。

可分离式面包屑底盘得益于采用可分离式面包屑底盘设计，机器清洁方便。

取消按钮，可即时关闭取消按钮可随时停止烘烤，实现安全和精确操作。

附加自动关闭防护功能附加自动关闭防护功能可防止产品短路。

内置面包烘烤架内置烘烤架，使您能轻松加热您喜爱的花式面包、糕点或小圆面包。

规格原产地原产地: 中国设计和外观颜色: 沙漠绿机身材料: 塑料普通参数烘烤控制级别数: 8产品功能: 可调节的烘烤程度, 自动关熄功能, 取消按钮, 冷却外壁, 解冻功能, 提升功能, 集成式电线储藏格服务2 年全球保修可持续发展用户手册: 100%可回收纸技术规格频率: 50-60 赫兹功率: 830 瓦电压: 220-240 伏重量和尺寸包装尺寸（长x宽x高）: 214x304x184 毫米产品尺寸（长 x 宽 x 高）: 188x275x156 毫米重量（含包装）: 1.512 千克产品重量: 1.120 千克© 2019 Koninklijke Philips N.V.保留所有权利。

烤面包机怎么用
烤面包机的使用方法如下：
1. 首先，将烤面包机放置在平稳的工作台面上，插上电源并打开电源开关。

2. 调整烤面包机的烤度旋钮，根据个人口味选择所需的烤度。

通常分为浅色、中等和深色烤度。

3. 拿出面包，将面包切片（宽度和厚度根据个人喜好），放入烤面包机的烤槽中。

4. 根据个人口感需求，可以在面包上涂上黄油、果酱或其他喜欢的调料。

5. 关上烤面包机的盖子，开始烘烤。

烤面包机通常具有自动弹起功能，当面包烤好时，会自动弹起。

6. 完成烤面包后，用热饮料或其他方法搭配，享用美味的烤面包。

请注意，使用烤面包机时要注意以下事项：
- 使用烤面包机时，建议在监督下进行，并避免儿童单独操作。

- 在启动烤面包机之前，请确保烤槽和外壳干净，并且没有残留物。

- 烤面包过程中，不要将手或金属物体放入烤面包机内部，以免触电或导致其他安全问题。

- 完成烤面包后，及时将电源开关关闭，以便节省能源并确保安全。

根据具体的烤面包机型号和品牌，使用方法可能会有所不同，还请在使用前查看烤面包机的说明书。

575 EC TOASTER OVEN575 EC TOASTER OVEN575 EC TOASTER OVEN575 EC TOASTER OVENWISCO INDUSTRIES, INC. OREGON, WISCONSIN 53575-0010 • TELEPHONE 608-835-3106 • FAX 608-835-7399LIMITED WARRANTYAll parts are guaranteed to be free of defects in material and workmanship for a period of one year from date of purchase, with the exception of the Infrared Quartz Lamps which are guaranteed for thirty days.Date of purchase shall be the day of shipment.Wisco agrees to replace or repair any part which proves defective, without charge for that part, during this one-year period.Parts will be replaced or repaired, F.O.B. factory, or by an authorized parts and service agency.During the initial 90-day period of the one-year warranty, Wisco will repair or replace without charge any defective parts, assume expenses incurred to perform the service, including up to a total of 50 miles travel. Travel expenses exceeding the 50 mile total shall be the obligation of the purchaser.Wisco Industries, Inc. neither assumes nor authorizes any person to assume any other obligation or liability in connection with this equipment.The above warranty applies only to the original purchaser, providing that the equipment has been properly installed, all parts have been serviced as recommended, and providing the allegedly defective parts, upon examination by Wisco, shall prove to be defective.This warranty will not apply to any equipment or part thereof which has been subjected to any accident, abuse, misuse, tampering, or service by an unauthorized service agency.CONTENTSINTRODUCTION 1 GENERAL 1MODEL DESCRIPTION 2 Construction2 SPECIFICATION SDimensionsElectricalOPERATING INSTRUCTIONS3-4 PreparationHandle Installatio nLamp InstallationPower Cord InstallationGENERAL MAINTENANCE5 LOCATION AND FUNCTION OF CONTROLS 5 OPERATION6 TROUBLESHOOTING GUIDE 6 REPLACEMENT PARTS (QUICK REFERENCE) 7 REPLACEMENT INSTRUCTION 8-9 LampsContr lyol AssembRelayFan MotorCOMPLETE PARTS LIST 10-11 575 EC EXPANDED VIEW DRAWING 12 575 EC WIRING DIAGRAM 13INTRODUCTIONWe congratulate you on your recent selection of the Wisco Model 575 EC Toaster Oven. Our organization has tremendous pride in presenting you with a dependable, top quality unit that is designed to provide you with years of reliable service.GENERALThe 575 EC offers speed with economy at the touch of a fingertip. Solid state reliability ensures consistent performance with each cycle when preparing items of your choice. The selective cycle setting provides the precise control for preparing the product to your exact specifications.With capacity for toasting 400 buns per hour, the 575 EC will handle your most demanding needs. With its unique ENERGY SMART circuitry design, energy consumption is minimized until services are required which saves 50-80% more energy than conveyor-type toasters.As a safety precaution, we recommend all instructions and safety tips appearing in this manual be reviewed prior to operation.MODEL DESCRIPTION CONSTRUCTIONWisco's Toaster Oven is constructed with a 22 gauge brushed stainless steel exterior and an aluminum interior. Specular aluminum reflectors focus the infrared waves to maximize efficiency when toasting or melting cheese. SPECIFICATIONSDIMENSIONSFigure 1. Model 575 EC Toaster OvenHeight: 9 1/4" Width: 23 1/2" Depth: 22"Opening height is 3 1/4" for a variety of productsELECTRICALThis unit is designed to operate on 208 AC, single phase. It is equiped with a 6 ft. cord and plug that requires a standard NEMA L6-20R or L6-30R receptacle rated 20 A, 250V AC, or 30 A, 250V AC, respectively.Upon request, NO POWER CORD will accompany the unit for firms that prefer to install their own power cord.Electical Rating: 208V AC 60 Hz 3200 WATT 15.4 Amp.OPERATING INSTRUCTIONSCAUTION: To prevent electrical shock, DO NOT apply power or try to operate toaster until after proper preparation of this unit.PREPARATIONPrior to operation, you must install the infrared lamps, grill tray handle, cleanout tray knob, and install a power cord (if requested without). The hardware and screws required to complete assembly are attached to the grill tray. The lamps are packaged internally beneath the top of the unit.HANDLE INSTALLATIONTransfer the handle from the interior of the grill tray to its exterior position. Screws are with handle (see figure 2).Figure 2. Handle AssemblyLAMP INSTALLATIONCAUTION: DO NOT touch the glass surface when handling the quartz lamps. The oil from your hands creates hot spots that will diminish the life of the lamps. When handling, grip the metal end caps.1. Remove the top of the unit to access the lamps. Two lamps are required for operation,2. Remove the inner lid. Avoid handling or bending the specular reflector shield attached to the lid.3. Install lamps by inserting the metal end caps into the white porcelain insulators, fitting the lamps snugly in placeand attaching lead to any terminal on insulator.4. Replace inner lid. Proper positioning places the air deflector on the side of the fan/control box. Secure at all sixpoints, required screws are in hardware packet.5. Replace top, required screws are in hardware packet.POWER CORD INSTALLATIONWhen installing a unit without a power cord (supplied upon request), we recommend a Type SO or SOW-A, #12 AWG 3-conductor cord, rated 20 amps, 250 volts.GENERAL MAINTENANCEProper maintenance includes regular cleaning. The exterior should be cleaned with glass cleaner or substitute cleaner that is not abrasive. DO NOT allow grease or dust particles to accumulate in the louvers. Adequate airflow is essential for proper cooling of the solid state components. The cleanout tray should be removed and cleaned daily. A standard detergent is recommended—dishwasher safe.If at some point you remove the top lid and there is a buildup of spattered particles on the specular aluminum reflector, DO NOT use a caustic oven cleaner or scratch pad when cleaning. It will damage the reflective finish. General detergents and a soft wipe are recommended. FUNCTION OF CONTROLS1. MAIN POWER SWITCHThis switch is used to turn the entering power line on and off.2. TIMING CONTROLUse this dial to regulate the length of the toast cycle. Each digit indicates an approximate 10 second cycle. For example, 1 is a 10 second cycle, 2 is a 20 second cycle, 6 is a 60 second cycle.3. START SWITCHThis momentary contact switch initiates the toast cycle.OPERATIONTo determine the appropriate calibration for your product, begin by setting the timer at 6, which is approximately a 60 second cycle—initiate cycle by pressing toast switch. If a darker finish is desired, advance the control to a higher setting. Reduce the setting for a lighter finish. Cycle times will vary depending on product weight and compostition. When melting cheese, begin with a lower setting. At the completion of the toast cycle, remove product. The unit is designed for consecutive cycles as demand requires.TROUBLESHOOTING GUIDEWhen more than one possible cause is listed, check the components in the order provided. The list is arranged from most probable cause to least.PROBLEM CAUSENo power to unit Unit not plugged in, main power switchin control assembly, relay, thermostat-limitingNo power to lamps Start button (toastswitch in controlassembly), relay, thermostatNo power to lamps after Blocked air vents, cooling fan,consecutive toast cycles lampUneven toasting Heat lamp burned out or lamp could beunpluggedNo power to unit except fan is on Blocked air vents, thermostat-limiting,after consecutive cycles connection between fan thermostat andfan, fan motor, fanNo tone at completion of toast cycle Control assemblyIrregular tone length Control assemblyUncontrolled toast cycle Control assemblyTROUBLESHOOTING GUIDE (continued)PROBLEM CAUSE Lamp does not stay on once started Lamp, control assembly, unit overheating—check fan motorREPLACEMENT PARTS LIST(QUICK REFERENCE)The following is a quick reference parts list designed for quick access and identification of common componentsREPLACEMENT INSTRUCTIONS LAMPS1. Disconnect unit from power.2. Unscrew top panel and remove.3. Unscrew reflector panel, and remove carefully, so as not to damage the sensor located ontop of the reflector panel.4. Remove lamp and replace with new lamp.5. Replace reflector panel.6. Replace top panel.7. Connect power to unit.CONTROL ASSEMBLY1. Disconnect unit from power.2. Unscrew (3) screws located on the bottom of the unit, and remove access panel.3. Disconnect wires to the control assembly.4. Unscrew (4) outside screws on the front of the control assembly.5. Remove control assembly.6. Install new control assembly by replacing (4) outside screws.7. Rewire according to wire diagram (see page 13).8. Replace access panel and tighten (3) screws.RELAY1. Disconnect unit from power.2. Remove access panel by removing (3) screws located on the bottom of the unit.3. Disconnect wires to the relay.4. Unscrew (2) screws located on the back side of the relay. NOTE: DO NOT WIPE AWAYTHERMAL GREASE. APPLY ADDITIONAL GREASE IF NECESSARY.5. Install new relay by replacing (2) screws.6. Rewire according to wire diagram (see page 13).7. Replace access panel and tighten (3) screws.FAN MOTOR1. Disconnect unit from power.2. Remove access panel by removing (3) screws located on the bottom of the unit.3. Disconnect (2) wires leading to the fan motor.4. Remove fan blade by lifting up on the hub of the fan carefully, so as not to break the blades of the fan.5. Remove (2) screws on both sides of the motor shaft.6. Remove fan motor, install new motor, and replace (2) screws on both sides of the motor shaft.7. Replace fan blade by aligning the flat on the motor shaft with the flat inside hub of the fan blade.8. Rewire according to the wire diagram (see page 13).9. Replace access panel and tighten (3) screws.COMPLETE PARTS LISTCOMPLETE PARTS LIST (continued)* If Requested For a detailed listing of electrical components and wires, see Figure 5 on page 13。

RPhone:+1Fax:+1(214)565-0976Toll Free:+1(800)527-2100Website: E-mail:*****************(214)421-7366INSTALLATIONANDOPERATING INSTRUCTIONSINTENDED FOR OTHER THAN HOUSEHOLD USERETAIN THIS MANUAL FOR FUTURE REFERENCEAPPLIANCE MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMESP/N 702020013/06CONTACT BUN TOASTERAPW WYOTT729Third Avenue Dallas,TX 75226This equipment has been engineered to provide you with year-round dependable service when used according to the instructions in this manual and standard commercial kitchen practices.Initial heating of appliance may generate smoke or fumes and must be done in a well ventilated area.Overexposure to smoke or fumes may cause nausea or dizziness.ANSI/NSF4(800)733-220324Hour Service HotlineModel:M2000-JIBTABLE OF CONTENTSSafety Precautions 2General Information 2Installation 3Location4Operating Instructions 4Cleaning5Daily Parts Cleaning 5Daily Conveyor Cleaning5One-Time Boil Out of Conveyor 6Daily Griddle Cleaning6Troubleshooting 8Specifications9Replacement Parts List w/Exploded View 10Wiring Diagram 12Warranty14SAFETY PRECAUTIONSGENERAL INFORMATIONAPW Wyott toasters are designed,built,and sold for commercial use and should be operated by trained personnel only.Clearly post all CAUTIONS,WARNINGS and operating instructions near each unit to insure proper operation and to reduce the chance of personal injury and/or equipment damage.Always disconnect power before cleaning or servicing the toaster.Surfaces will remain hot after power has been turned off,allow unit to cool before cleaning or servicing.Never clean the toaster by immersing it in water.The toaster is not protected against water jets;DO NOT CLEAN TOASTER WITH A WATER JET.Always clean equipment before first use.Operating toaster without legs will void the warranty.Insure all accessories and exterior panels are properly installed and adjusted before applying power and operating.Check the rating label for your model designation and electrical rating.Rating Label is located on the bottom front of the control panel.Overall dimensions with feeder:23.5"(59.7cm)W x 25.9"(65.8cm)H x 17.5"(44.5cm)D M2KA:208VAC,2880W,13.8A60Hz M2KH:240VAC,3840W,16A60Hz208/250V:NEMA6-20P Plug,4foot,3wire grounded cord.If the supply cord is damaged,the manufacturer or an authorized service agent or a similarly qualified person must replace it to avoid a hazard or warranty.94lbs (42.7Kg)Electrical Ratings:Cordset Configuration:Shipping Weight:INSTALLATION1.Examine carton for damagea.Apparent damage or loss must be noted on the freight bill at the time of delivery.must sign b.Concealed damage or loss if not apparent until after the toaster is removed fromcarton,Be sure to save all contents and packaging material.2.Verify PartsThe freight carrier has assumed responsibility for its safe transit and delivery.If equipment is received damaged,either apparent or concealed,a claim must be made with delivering carrier.The carrier representative (Driver)the freight bill.If this is not done,the carrier may refuse the claim.The carrier can supply the necessary forms.a request for inspection must be made to the carrier within 15days.The carrier should arrange an inspection.After removing unit from the shipping carton,unwrapping loose parts and remove any packing tape,plastic wrap and nylon tie-down.Verify the following parts:Item Packaging Qty NOTE:3.Assemble LegsLegsIn plastic bag4Feeder/Bun Chute Wrapped,loose in top of carton 1ConveyorIn individual carton 1Instruction ManualLoose in carton 1Teflon Sheet Kit (optional)Loose in cartonOptionalPRIOR TO INITIALSTART-UP ,ALL REMOVABLE PARTSAND THE GRILLSURFACE SHOULD BE CLEANED WITH WARM SOAPY WATER TO REMOVE MANUFACTURING OILS,THEN RINSED AND DRIED THOROUGHLY .Apply oil (vegetable oil)to the conveyor chain after washing.(Bun oil can be used if it contains no animal fats,salts or dairy products).Lay the toaster on its back and install the four adjustable legs into the threaded holes on the bottom of the toaster sides.Hand tighten the legs by gripping the black shank and turning until it is seated firmly against the bottom of the toaster.Set the toaster upright on a flat surface.Unscrewing the lower,chrome insert of each leg levels the unit.Flats are provided on two sides of the insert to allow use of a wrench. Precise leveling is not required for proper operation.4.Conveyor InstallationRemove the front panel by lifting it straight up.(See Figure 1)Lift conveyor assembly by using U shaped handles on each conveyor side bracket.Lower the conveyor into the two conveyor hanger brackets above the grill plate on each side,so the four spacers on the sides of the conveyor rest on the bottom flange and the bottom spacers are against the adjustment screws.The conveyor hanger brackets are factory adjusted.However,before reinstalling the front panels apply power to the unit and run the conveyor to insure proper gear engagement.If gears are not properly engaged,adjust the conveyor by loosening the jam nuts on the conveyor hanger brackets and adjusting the screw (see Figure 2)to set the conveyor tothe correct height.Retighten lock nuts after adjustment is complete.a.To adjust the conveyor up into the drive gear,turn the conveyor adjustment screwe a 7/16-end wrench to tighten the jam nut.b.To adjust the conveyor away from the drive gear,turn the conveyor adjustment screwe a 7/16-end wrench to tighten the lock nut.5.Replace front panel.6.FeederAssembly7.Install Teflon Sheet (Optional)Install Feeder by fitting slots on back of feeder onto back panel studs located at top rear of unit.Remove Feeder.Allow one end of the Teflon sheet to overlap the top of the rear panel to the rear studs.Align the holes in the sheet with the stud heads and push the sheet over the stud heads.Balance of the sheet will fit over the grill surface.Reinstall Feeder c a p t u r i n g Te f l o n S h e e t b e t w e e n the feeder and the top of the toaster.FIGURE 2Jam NutLOCATIONOPERATING INSTRUCTIONSPlace the toaster on a flat surface.This toaster is tested and approved for zero clearances against surfaces.Locate the toaster near a wall receptacle of the proper configuration.Plug the power cord into an outlet (receptacle)of the specified voltage on the rating label.Outlets must be properly grounded.Choose Dry or Wet operation.(no oil)Insure Teflon sheet,86298is properly installed.a.Turn Main Power Switch on.Set Temperature Control knob to desired temperature.Allow PilotLight to cycle at least two times (on/off).When the light is on,the grill is heating.Heat up time is about 15-20minutes.b.Turn on motor switch.Conveyor should start to turn.c.Place bun halves on feeder cut side down (facing grill surface).Toast time is approximately 210sec.depending on bun height and diameter.Increase or decrease temperature setting to achieve desired brownness and temperature.(using oil)Apply a light coating of oil to grill surface.(Fry oil can be used)When toasting using oil,any high-quality cooking oil may be used with this toaster (do not use oils that contain dairy products such as butter).The Teflon sheet may be used,but it is not required.a.Turn Main Power Switch on.Set Temperature Control knob to desired temperature.Allow PilotLight to cycle at least two times (on/off).When the light is on,the grill is heating.Heat up time is about 15-20minutes.b.Turn on motor switch.Conveyor should start to turn.c.Hold bun half in the palm of the hand,place butter on cut side..d.Place bun halves on feeder cut side down (facing grill surface).Try several buns to determinethe correct pressure and time to achieve the desired browning and temperature of ing too little oil will cause the bun surface to be cool and uneven in color.It will also cause the bun to stick to the ing too much oil will give the bun a yellow un-toasted look.Toast time is approximately 210sec.depending on bun height and diameter.Increase or decrease thenon-heated DO NOT USE AN EXTENSION CORD.1.Dry operation.2.Wet operation.temperature setting to achieve desired brownness and temperature.Should the temperature setting be changed,allow several cycles for the grill plate to adjust.Once the desired setting has been achieved,note the temperature and keep it set there.Turn off main power switch and conveyor switch.Disconnect the power supply cord from the wall outlet.The toaster will be hot when turned off.Allow the toaster to cool for at least 15 30minutes before handling.during disassembly and cleaning.Remove the Top and Bottom Front Panels.The Feeder,and Top and Bottom Front Panel can be placed in a dishwasher or sink and washed with detergent and warm water.Remove the conveyor assembly by gripping the two handles at the top and lifting forward until it clears the gears.Lift it up and out gently placing it in a sink with the drain stopped,or in a suitable container to soak over night.Conveyor can be placed in the sink or container while warm.The soak solution is a mix of 10parts hot water (120ºF or more)to 1part (minimum) INSIDE OUT brand 3-IN-1.Fill the sink or suitable container with the solution,to completely cover the conveyor by approximately one inch.Allow the conveyor to soak in the solution over night.Remove the conveyor from the e a stiff non-metal brush or plastic pad to remove residual bun oil.Insure the chains are clean and free from e a brush to remove any soil or debris remaining on the chain.Rinse conveyor with plain hot water and allow to drain.Lubricate both chains thoroughly with vegetable oil.Bun oil may be used if it contains no animal fats,salts or dairy products.Gently replace conveyor into toaster.Replace all removed toaster parts.Plug power supply cord into wall outlet.Turn main power switch on.Turn conveyor switch on.Severely baked on oils as shown in Figure 3require the conveyor to be cleaned using the one-time boil out instructions below to clean.NOTE:WARNING:Make sure the toaster is in the off position and has been off at least 15 30minutes.Do not attempt this cleaning procedure if the toaster components are too hot to touch.Never spray water on the toaster or controls.Damage to the toaster as well as injury could occur.Severe injury and burns may occur if you do not follow this instruction sheet.DISASSEMBLYUSE CAUTION NOTE:Do not use any chloride or chlorine -based products to clean or rinse toaster or toaster parts.Daily Parts Cleaning:Daily Conveyor Cleaning:Conveyor may be hot and is heavy,use caution when lifting and e caution when handling a hot conveyor.Note:Chain Lubrication is critical to chain life.Oil the chain daily.Discard used soak solution.Clean and sanitize sink or container after over night use!CLEANINGFIGUREONE-TIME BOIL OUT OF CONVEYORNOTE:This is for experienced operators only,and in stores that approve this operation.Gently NOTE:Drain the solution prior to removing the Conveyor Assembly.Note:Chain Lubrication is critical to chain life.Oil chain daily.LAST IMPORTANT NOTE:KEEP CONVEYOR LOOKING NEW.1.Turn off power and drain the oil from one of the Fryers,and allow it to cool.2.Turn Toaster main power switch off.Remove power supply plug from the wall outlet.3.Some surfaces will remain hot after toaster is turned off.Allow time for toaster to cool.(15-30minutes)Use caution during disassembly and cleaning.4.Remove the Top and Bottom Front Panels.5.When the fryer has cooled and has drained,close the drain valve.6.Remove the Conveyor assembly by grasping the two handles at the top,and lifting forward untilit clears the gears.7.place the ConveyorAssembly into the Fryer.8.Add water to the cooled Fryer leaving enough room to add two (2)gallons of INSIDE OUT 3IN1HEAVY DUTY CLEANER and the ConveyorAssembly.9.Add additional water to the Fryer,if necessary,to completely cover the ConveyorAssembly.10.Set the temperature of the Fryer to 200ºF,and allow the conveyor to soak in the solution for 60minutes.11.Shut off the Fryer and allow the conveyor to cool.12.After the conveyorhas cooled,remove the conveyor from the Fryer.If there are areas with bun oil,use a stiff non-metal brush or plastic pad to remove.Insure the chains are clean and free from e a brush to remove any soil or impediment remaining on the chain.13.Rinse conveyor with hot water and allow to drain.Lubricate both chains thoroughly withvegetable oil.Bun oil may be used if it contains no animal fats,salts or dairy products.14.Before assembly of the conveyor check the Following:Conveyor Assembly hardware to insurefasteners are tight and there are no signs of wear,Gears are tight on the Conveyor shaft and the Motor Shaft and the Hanger Bracket screws are tight and the brackets have not shifted during use.15.Gently replace conveyor into toaster.Replace all removed parts.Plug power supply cord intowall.Turn main power switch on.Turn conveyor switch on.Daily-cleaning instructions of conveyor should be followed after this boil out.The conveyor must stay clean to optimize speed and bun temperature.Daily Griddle Cleaning:Dry Operation:Wet Operation:Tools needed for cleaning:Also needed:Wipe off the Teflon sheet with a damp cloth to remove any debris or particles that have collected on the sheet.If the sheet is worn,replace it with a new sheet.It is not necessary to completely remove residue,as long as the grill surface is smooth and free of burned on bread that may cause buns to stick.Scotch-BriteTM Quick Clean SmallAppliance Cleaner No.702or Equivalent Scotch-BriteTM Multi-Purpose Pad Holder No.405or Equivalent Scotch-BriteTM Squeegee No.410or EquivalentScotch-BriteTM Griddle Polishing Pad No.46or Scotch-Brite General Purpose Scrubbing Pad No.9650or Equivalent (Wet)terry towelCatch pan for food soilCommon kitchen scraperFIGURE 4FIGURE 5FIGURE 6Scour using Scotch-Brite Multi-Purpose Pad Holder No.405or equivalent,and Scotch-Brite Griddle Polishing Pad No.46(or 9650).(See Figure 4)After scouring,Squeegee the surface clean with the Scotch-Brite Squeegee No.410(See Figure 5)Turn off Bun Grill Toaster and wipe surface with clean wet towel.If the surface is still hot,use the Scotch-Brite Multi Purpose Pad Holder to move the towel over the surface.(See Figure 6)Dry the grill thoroughly.Coat the grill plate with a light film of cooking oil.See Figure 7)Rinse all cleaning tools with hot water.(See Figure 8)Wipe down all external stainless steel surfaces with a damp cloth.Before assembling the conveyor check the following:Fasteners on the Conveyor Assembly hardware should be tight with no signs of wear.Conveyor Shaft Gear and Motor Shaft Gear are tight.Hanger Bracket Screws are tight and the brackets have not shifted during use.TM TM TM TM RE-ASSEMBLYIf Teflon sheet is installed remove it when Bun Grill Toaster is cool.Set the toaster temperature to 350°F .Scrape loose food particles with scraper into a pan under grill plate.Squeeze 1to 2ounces of Scotch-BriteTM Quick Clean Small Appliance Cleaner No.702or equivalent into measuring reservoir of bottle.Pour cleaner onto pad.Do not pour directly onto grill surface.TROUBLESHOOTING GUIDEAlways ask and check the following:Is the unit connected to a live power source of the proper voltage?Check the circuit breaker.Is power switch ON and pilot light glowing?Check the rating label.Is the unit connected to the correct power source?If the above checks out,and you still have problems,call an APW Wyott authorized service agent.1.2.3.4.APW SERVICE HOT LINE 1-800-733-2203IMPORTANT FOR FUTURE REFERENCEPlease complete this information and retain this manual for the life of the equipment.For Warranty Service and/or Parts,this information is required.Model Number Serial Number Date Purchased Notes:Notes:Phone:+1Fax:+1(214)565-0976Toll Free:+1(800)527-2100Website: E-mail:*****************(214)421-7366APW WYOTT729Third Avenue Dallas,TX 75226(800)733-220324Hour Service HotlineR。

烤面包机维修技巧修复烤面包机出现的加热不均匀或无法弹起的故障烤面包机是我们日常生活中常见的厨房电器之一，它为我们提供了便捷的早餐选择。

然而，有时我们可能会遇到一些烤面包机的故障，比如加热不均匀或无法弹起。

这些问题的出现给我们的使用带来了不便，但是幸运的是，我们可以通过一些简单的维修技巧来修复这些故障。

本文将为大家介绍几种常见烤面包机故障的维修方法。

1. 加热不均匀的问题加热不均匀是烤面包机常见的故障之一。

这种问题的出现可能是由于面包机内部加热元件的老化或损坏导致的。

要修复这个问题，首先需要确保烤面包机已断电并完全冷却。

然后，使用螺丝刀拆下机器的外壳，小心检查加热元件是否有裂痕或氧化现象。

如果有，建议将加热元件更换为新的。

此外，还有一种可能是由于加热控制器的故障导致的加热不均匀。

加热控制器是控制烤面包机加热温度的关键元件。

如果加热控制器出现故障，可能会导致加热不均匀。

在此情况下，建议将加热控制器更换为新的。

请务必确保使用相同型号和规格的加热控制器。

2. 无法弹起的问题当烤面包机无法弹起时，可能是由于卡住或损坏的弹簧机构引起的。

要修复这个问题，首先需要断开电源并等待烤面包机完全冷却。

然后，使用螺丝刀将烤面包机的外壳打开，检查弹簧机构是否受损或卡住。

如果发现问题，可以尝试重新调整弹簧的位置或者更换弹簧。

如果弹簧机构损坏严重，建议更换新的弹簧机构。

此外，还有一种可能是由于弹簧机构周围的脏污导致的无法弹起问题。

长期使用后，面包屑和油渍可能会积累在烤面包机的底部和弹簧机构周围，导致弹簧无法正常弹起。

在这种情况下，建议使用刷子或压缩空气清洁烤面包机底部和弹簧周围的脏污。

清洁后，再试一下是否可以正常弹起。

在进行任何维修之前，务必记住断开烤面包机的电源，并等待烤面包机完全冷却。

此外，如果您对电器维修没有经验或者不确定如何进行修复，建议寻求专业技术人员的帮助。

总之，烤面包机加热不均匀或无法弹起的故障是我们日常生活中常见的问题之一。