刀形浆闸阀 (英文翻译)
- 格式:doc
- 大小:39.00 KB
- 文档页数:7
第二节阀门术语一、阀门类别(中英文对照)闸阀[Gatevalve;Slidevalve]截止阀[Globevalve;Stopvalve]止回阀[Checkvalve;Non-returnvalve]球阀[Ballvalve]蝶阀[Butterflyvalve]旋塞阀[Plugvalve]节流阀[Throttlevalve]隔膜阀[Diaphragmvalve]针型阀[Pintlemvalve]低温阀[Lowtemperaturevalve]二、结构及零件(中英文对照)结构长度[FacetoFace;EndtoEnd;FacetoEnddimension] 结构形式[Typeofconstruction]角式[Angletype]直通式[Throughwaytype]保温式[Steamjackettype]连接形式[Typeofconnecting]电动装置[Electricactuator]气动装置[Pneumaticactuator]齿轮操作[Gearoperation]手轮操作[Handwheel]阀体[Body]阀盖[Bonnet;cover;cap;lid]阀瓣[Disc]闸板[Wedge]阀杆[Stem;Spindle]阀杆螺母[Stemnut;Yokenut]填料函[Stuffingbox]填料压盖[Gland]支架[Yoke]上密封[Backseat]阀座[Seat]螺栓[Blot]螺母[Nut]填料[Packing]球体[Ball]销轴[Hingepin]摇杆[Arm;Hinge]密封面[Sealface]主要性能参数[Specification] 公称压力(PN)[Nominalpressure]公称通径(DN)[Nominaldiameter]工作压力[Workingpressure]壳体试验[Shelltest]密封试验[Sealtest]三、其它术语(中英文对照)BW表示对焊连接方式SW表示承插焊连接方式=全通径BB-螺栓连接阀盖PSB-内压自密封阀盖=齿轮操作BG-伞齿轮PWHT-焊后热处理PCD-中心圆直径=硬质面CS-碳钢FS-锻钢AS-合金钢SS-不锈钢CI-铸铁OS&Y-明杆支架结构。
阀门种类术语英汉对照Air valves 空气阀门Angle Stop valves Plug valve角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves Check valve门角式截止阀Ash valves 排灰阀Aspirating valves 吸(抽)气阀Auxiliary valves 辅助(副)阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料(放空,排污)阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板Emergency Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves Hydraulic control valve法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves Forged Steel Valve衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀Magnetism Force Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀)Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力(増压)阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀)Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀Single Opening Exhaust Valves 单口排气球Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵)Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Lining对夹式衬胶蝶阀Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器。
Valve 阀门General valve 通用阀门"Gate valve 闸阀"Globe valve 截止阀Throttle valve 节流阀Ball valve 球阀Diaphragm Valve 隔膜阀"Cock 旋塞阀"Check valve 止回阀Safety valve 安全阀Pressure reducing valve 减压阀Automatic steam trap Trap蒸汽疏水阀Low pressure valve 低压阀门Middle pressure valve 中压阀门High pressure valve 高压阀门Super high pressure valve 超高压阀门High temperature valve 高温阀门Sub-zero valve 低温阀门Cryogenic valve 超低温阀门Face-to-face dimension End-to-end dimension Face-to-centre dimension结构长度Type of construction 结构形式Through way type 直通式Angie type 角式"Y-globe type 直流式Three way type 三通式T-pattern three way T形三通式L-pattern three way L形三通式Balance type 平衡式Lever type 杠杆式Normally open type 常开式Normally closed typ 常闭式Steam jacket type 保温式Bellows seal type 波纹管密封式Body 阀体"Bonnet 阀盖Disc 启闭件Disc 阀瓣Seat ring 阀座Sealing face 密封面"Stem 阀杆Yoke bushing Yoke nut阀杆螺母Stuffing box 填料箱Gland 填料压盖"Packing 填料"Packing seat 填料垫Yoke 支架"Back seat 上密封Pressure seat 内压自封Dimension of valve stem head 阀杆头部尺寸Dimmension of valve stem end 阀杆端部尺寸Dimension of connecting channel 连接槽尺寸Type of connection 连接形式Electric actuator 电动装置Pneumatic actuator 气动装置Hydraulic actuator 液动装置Eletro magnetic actuator 电磁动装置Eletro hydraulic actuator 电-液动装置Eletro magnetichydraulic actuator 电磁-液动装置Pneumatic-hydraulic actuator 气-液动装置Wormgear actuator 蜗轮传动装置Cylindrical gear actuator 圆柱齿轮传动装置Conical gear actuator 圆锥齿轮传动装置Outside screw stem rising through handwheel type gate valve 明杆闸阀Inside screw nonrising stem type gate valve暗杆闸阀Wedge gate valve 楔式闸阀Parallel gate valve Parallel slide valve平行式闸阀Wedge disc 闸板Single gate disc 单闸板Double gate disc 双闸板Flexible gate disc 弹性闸板Ball 球体Float ball valve 浮动式球阀Fixed ball valve 固定式球阀Disc 蝶板Vertical disc type butterfly valve 垂直板式蝶阀Indined disc butterfly valve 斜板式蝶阀Diaphragm 隔膜Weir diaphragm valve 屋脊式隔膜阀Globe diaphragm valve 截止式隔膜阀Wedge diaphragm valve 闸板式隔膜阀Plug 塞子Gland packing plug valve 填料式旋塞阀Lubricated plug valve 油封式旋塞阀Lift check valve 升降式止回阀Vertical lift check valve 升降立式止回阀Swing check valve 旋启式止回阀Foot valve 底阀Double disc swing foot valve 旋启双瓣式底阀Multi-disc swing foot valve 旋启多瓣式止回阀Butterfly swing check valve 蝶式止回阀Hinge pin 销轴"Arm 摇杆Direct loaded safety valve 直接载荷式安全阀Assisted safety valve 带辅助装置的安全阀Supplementary loaded safety valve 带补充载荷的安全阀Pilot operated safety valve 先导式安全阀Direct spring loaded safety valve 弹簧式安全阀Lever and weight loaded safety valve 杠杆式安全阀[Throat diameter 喉径Fall lift safety valve 全启式安全阀Low lift safety valve 微启式安全阀Seal type 封闭式Unseal type 不封闭式Bellows seal balance safety valve 波纹管平衡式安全阀Duplex safety valve 双联弹簧式安全阀Adjusting bolt Adjusting screw 调节螺套Spring plate 弹簧座Valve guide disc guide 导向套Disc holder 反冲盘Adjusting ring 调节圈Diapjragm reducing valve 薄膜式减压阀Spring diaphragm reducing valve 弹簧薄膜式减压阀Piston reducing valve 活塞暱减压阀Bellows weal reducing valve 波纹管式减压阀Lever reducing valve 杠杆式减压阀Fixed pressure reducing valve 定值减压阀Proprutioning pressure reducing valve 定比减压阀Fixed differential reducing valve 定差减压阀Direct-acting reducing valve 直接作用式减压阀Pilot-operated reducing valve 先导式液压阀Diaphragm reducing valve 薄膜式减压阀Piston reducing valve 活塞式减压阀Bellows reducing valve 波纹管式减压阀Direct acting reducing valve 正向作用式减压阀Reverse acting reducing valve 反向作用式减压阀Balanced reducing valve 卸荷式减压阀Pilot valve 导阀Main valve 主阀Regulation spring 调节弹簧Returnning spring 复位弹簧Diaphragm 膜片Ball float steam trap 浮球式疏水阀Inverted bucket steam trap 钟形浮子式疏水阀Open bucket steam trap 浮桶式疏水阀Bimetal elements steam trap 双金属片式疏水阀Impulse steam trap 脉冲式疏水阀Shemostatic team trap 圆盘式疏水阀Disc 阀片Inverted bucket 钟形罩Ball float 浮球Bucket float 浮桶Specifeca tion speeification 主要性能参数Nominal pressure 公称压力Nominal diameter 公称通径Working pressure 工作压力Working temperature 工作温度Suitable medium 适用介质Suitable temperature 适用温度Shell test 壳体试验Seal test pressure 壳体试验压力Seal test 密封试验Seal test pressure 密封试验压力Back seal test 上密封试验Leckage 渗漏量Percent of contact area 吻合度Type 类型Type Model 型号"Prime out-form dimensions 主要外形尺寸Conncetion cimension 连接尺寸Set pressure 整定压力Overpressure of a safety valve 超过压力Re-seating pressure of a safety valve 回座压力Blowdown of a safety valve 启闭压差Cold differential test pressure 冷态试验差压力Relieving pressure 排放压力Brilt-up back pressure 排放背压力Superimposed back pressure 附加背压力Lift 开启高度Commencement of lift 起始升程Flow area 流道面积Flow diameter 流道直径Curtain area 帘面积Theoretical flowing capacity 理论排量Coefficient of discharge 排量系数Derated coefficient of discharge 额定排量系数Certified capacity 额定排量Equivalent calculated capacity 当量计算排量Chatter 频跳Flutter 颤振Static characteristics 静态特性Dynamic characteristics 动态特性Flow characteristics 流量特性Pressure characteristics 压力特性Static characteristics derivation 静态特性偏差Flow characteristics derivation 流量特性偏差Pressure characteristics derivation 压力特性偏差Relative static characteristics derivation 相对静偏差Relative flow characteristics derivation 相对流量特性偏差Relative pressure characteristics derivation 相对压力特性偏差Pressure increasing ratio 压力增长系数Maximum flow rate 最大流量Pressure reducing ratio 减压比Lockup pressure 关闭压力Maximum allowable pressure 最高允许压力Operating pressure 工作压力Maximum operating pressure 最高工作压力Minimum operating pressure 最低工作压力Operating back pressure 工作背压Maximum operating back pressure 最高工作背压Rate of back pressuec 背压率Maximum rate of back pressure 最高背压率Operting differential pressure 工作压差Maximum differential pressure 最大压差Minimum differntial pressure 最小压差Operating temperature 工作温度Maximum operating temperature 最高工作温度Maximum allwable temperature 最高允许温度Opening valve temperature 开阀温度Closing valve temperature 关阀温度Temperature at discharging condensate 排水温度Maximum temperature at discharging 最高排水温度Subcoold temperature 过冷度Subcooled temperature of open valve 开阀过冷度Subcooled temperature of close valve 关阀过冷度Maximum subcoold temperature 最大过冷度Minimum subcooled temperature 最小过冷度Cold condensate capacity 冷凝结水排量Hot condensate capacity 热凝结水排量Steam loss 漏汽量No-load steam loss 无负荷漏汽量Load steam loss 有负荷漏汽量Rate of no-load steam loss 无负荷漏汽率Rate of load steam loss 有负荷漏汽率Rate of load condensate 负荷率abrasion 磨损;磨蚀abruption 中断;断路abscissa 横坐标absorbability 吸收能力absorbent 吸收剂;吸附剂absorber 吸收剂;吸附器;阻尼器;减震器vibration absorber 减震器;吸震器;阻尼器absorption 吸收energy absorption 能量收吸sound absorption 吸音acceleration 加速度acceleration due to gravity 重力加速度absolute acceleration 绝对加速度angular acceleration 角加速度axial acceleration 轴向加速度brief acceleration 短暂加速度centrifugal acceleration 离心加速度centripetal acceleration 向心加速度circular acceleration 圆周加速度Coriolis acceleration 哥氏加速度fluctuating acceleration 变动加速度;脉动加速度free fall acceleration 自由落体加速度gravity acceleration 重力加速度initial acceleration 初始加速度linear acceleration 线(性)加速度negative acceleration 负加速度normal acceleration 法向加速度radial acceleration 径向加速度relative acceleration 相对加速度resultant acceleration 合加速度uniform acceleration 匀加速度;等加速度accelerometer 加速度计;过荷传感器acceptance 验收accessories 附件accident 事故accumulation 积累;存储boundary layer accumulation 边界层增厚;边界层积聚liquid accumulation 流体积存accumulator 蓄能器;蓄电池;累加器accuracy 准确性;精度accuracy in calibration 标定精度;校正精度accuracy of instrument 仪表精(确)度accuracy of manufacture 制造精度accuracy of measurement 量测精度;测量准确度accuracy of reading 读数精度calibration accuracy 校准精度;标定精度geometrical accuracy 几何精度overall accuracy 总精度relative accuracy 相对精度acetaldehyde 己醛;醋醛acetate 乙醋盐cellulose acetate 醋酸纤维素acetone 丙酮acid 酸acetic acid 乙酸;醋酸benzoic acid 安息香酸;苯(甲)酸bor(ac)ic 硼酸carbolic acid 石炭酸;苯酚carbonic acid 炭酸fatty acid 脂肪酸;油酸formic acid 甲酸;蚁酸hydrochloric acid 盐酸hydrocyanic acid 氰化氢;氢氰酸mixed acid 混合酸naphthenic acid 环烷酸nitric acid 硝酸oleic acid 脂肪酸;油酸oleinic acid 脂肪酸ortho-phosphoric acid 正磷酸oxalic acid 草酸;乙二酸palmitic acid 棕榈酸phenic acid 石炭酸;苯酚picr(anis)ic acid 苦味酸;黄色炸药picronitric acid 苦味酸;黄色炸药;苦硝酸stear(ol)ic acid 硬脂酸sulfuric acid 硫酸sulphuric acid 硫酸tartaric acid 酒石酸acidity 酸度;酸性acme 顶点action 作用;动作;运转boundary layer action 边界层效应delayed action 延缓作用;迟滞作用;滞后作用lifting action of vane 叶片的升力作用2005-12-9 14:52:00 如果您有什么要求欢迎直接和我们的管理组联系xingguang等级:贵宾威望:2文章:847积分:2223门派:无门无派注册:2005年11月16日第 2 楼--------------------------------------------------------------------------------throttling action 节流作用wall action 边壁作用actuator 促动器;执行元件;传动装置diaphragm actuator 隔膜传动装置;隔膜驱动杆adapter 接头;承接管;连接件;接合器adaptor 连接件;接头;承接管;接合器pipe adaptor 管接头;管连接套addition 增加;加法;加;附加物additive 添加剂;附加的adhesion 粘着;附着adjustment 调整;调节;调准机构zero adjustment 调零admission 进气;供给admission of air 补气;吸气adsorption 吸附(作用)advance 超前;阿范斯电阻合金(56%、锰1.5%,其余镍)aerodynamics (空)气动力学aerofoil 翼型;翼剖面aeromechanics 空气动力学;航空力学aerostatics 空气静力学afflux 流入afterbay 下游;后架间ageing 老化;时效artificial ageing 人工老化agent 介质;剂addition agent 添加剂additive agent 添加剂air 空气compressed air 压缩空气alrbrake 空气制动器air-cooling 空气冷却aircurrent 气流airflow 气流airfoil 翼型;翼剖面air-friction 空气摩擦airing 通风;通气air-spring 气垫air-tightness 气密性;密封性albronze 铝青铜alcohol 酒精;乙醇algebra 代数alignment 定心;(直线)校准;校直alkalescence 碱度;碱性alkali 碱;强碱caustic alkali 强碱alkalinity 碱度;碱性allowance 公差;余量fitting allowance 装配公差alloy 合金acid resisting alloy 耐酸合金aluminium alloy 铝合金anticorrosion alloy 抗蚀合金antifriction alloy 抗磨合金bearing alloy 轴承合金corrosion-resisting alloy 耐蚀合金Corson alloy 铜镍硅合金;科森合金heat resisting aluminium alloy 耐热铝合金high tensile aluminium alloy 高强度铝合金lead base alloy 铅基合金light alloy 轻合金magnetic alloy 磁性合金natural alloy 天然合金non-ferrous alloy 有色金属合金alpaca 镍黄铜alpax 阿派铝合金;铝硅合金(87%铝;13%硅)altitude 高度critical altitude 临界高度geometric altitude 几何高度aluminium 铝amendment 改善;修正ammeter 安培计ammonia 氨aqua ammonia 氨水aqueous ammonia 氨水ampere 安(培)amplifier 放大器amplitude 振幅;范围analogy 相似;模拟hydraulic analogy 水力相似Reynolds analogy 雷诺相似analyser 分析器analysis 分析approximate analysis 近似分析dimensional analysis 因次分析;量纲分析dynamic analysis 动力分析;动态分析error analysis 误差分析harmonic analysis 调和分析;谐波分析stress analysis 应力分析vector analysis 向量分析analyzer 分析器angle 角加速度angle of attack 攻角;迎角;冲角angle of contact 接触角angle of delay 滞后角angle of incidence 入射角angle of lag 滞后角angle of rotation 旋转角angle of shift 位移角angle of stall 失速攻角angle of sweepback 后掠角actual angle of attack 实际攻角acute angle 锐角blade angle 叶片安装角blade inlet angle 叶片进口角blade outlet angle 叶片出口角chord angle 翼弦安放角contact angle 接触角critical angle of attack 临界攻角;临界迎角discharge angle 出流角entrance angle 入口角Euler angle 欧拉角exit angle 出口角gliding angle 下滑角incident angle 攻角;迎角;冲角inflow angle 流入角inlet angle 入口角inlet blade angle 叶片入口角outlet angle 出口角pressure angle 压力角profile angle 翼型角sliding angle 滑移角;滑动角stalling angle of attack 失速攻角subtended angle of blade 叶片包角vane angle 叶片安放角vane entrance angle 叶片入口角vane setting angle 叶片安放角wrapping angle of blade 叶片包角anhydride 酐acetic anhydride 醋酸酐;无水醋酸anisotropy 异向性annealing 退火anticorrosion 耐蚀aperture 孔径;开度;孔隙;孔光圈apex 顶点apparatus 装置;仪器calibrating apparatus 校准装置guide apparatus 导向装置appliance 装置approximation 近似法;近真法;近似值;逼近法successive approximations 逐次逼近法aqua 水aqua reqia 王水Araldite 环氧(类)树脂;合成树脂粘结剂;阿拉伐area 面积;区域;范围cross section area 横截面积effective area 有效面积effective sectional area 有效截面积exit angle 出口面积impeller iniet area 叶轮进口面积passage area 流道(横截)面积specific surface area 比表面积;单位表面积throat area 喉部面积areometer 液体比重计;浮秤areopycnometer 液体比重计;浮秤;稠液比重计argument 辐角;自变数;论证arm 臂;支管;指针adjusting arm 调节杆regulating arm 调节杆rocking arm 摇臂valve arm 气阀摇臂valve driving arm 阀驱动臂valve motion arm 阀驱动臂armature 电枢;铠装;加强料;衔铁armour 铠装arrangement 配置;装置diagrammatic arrangement 简化布置图;示意布置图pipe arrangement 管系布置tube arrangement 管布置arrow 箭头;指针asbestos 石棉2005-12-9 14:54:00 中国泵阀联盟预祝您新年新红火xingguang等级:贵宾威望:2文章:847积分:2223门派:无门无派注册:2005年11月16日第 3 楼-------------------------------------------------------------------------------- phenolic-bonded asbestos 酚醛胶合石棉resin-bonded asbestos 树脂胶合石棉resin-impregnated asbestos 树脂浸渍石棉asphalt 沥青assay 试样;试验;分析assembling 装配;收集;装置assembly 部件;机组;汇编asymmetry 非对称性atmosphere 大气;大气压standard atmosphere 标准大气(压)technical atmosphere 工程大气压atomizer 喷雾器;喷嘴oil atomizer 油喷嘴spray atomizer 喷雾器atomizer-pump 喷雾器-泵组attachments 附件austenite 奥氏体auto-alarm 自动报警器automation 自动化autostabilizer 自动稳定器auxiliaries 辅助设备;辅机axes 轴solid axess 空间坐标轴space axess 空间坐标轴space coordinate axess 空间坐标轴axis 轴axis of abscissa 横坐标轴axis of coordinates 坐标轴coordinate axis 坐标轴eddy axis 旋涡轴线horizontal axis 水平轴线vortex axis 旋涡轴线axle 轴idler axle 中间心轴intermediate axle 中间心轴stub axle 短心轴babbit 巴氏合金back 背;背面;底座;基座back of vane 叶片背面blade back 叶片背面back-flow 回流back-river 上游backwater 壅水;回水;死水baffle 障板;挡板;导流片guide baffle 导向叶片;导向筋bakelite 电木;酚醛塑料balance 平衡;天平;秤aerodynamic balance 气动力天平dynamic balance 动态平衡energy balance 能量平衡force balance 测力天平;力平衡heat balance 热平衡;热量平衡表moment balance 力矩天平;力矩平衡static balance 静态平衡three-component balance 三分力天平balancer 平衡器;配重moment balancer 力矩天平balancing 平衡(法);配平dynamic balancing 动态平衡ball 球valve ball 阀球band 带;条;波带;频带;波段;范围dead band 死区;盲带vortex band 涡层;涡流带bar 杆;杆件;巴(压力单位);阻止balance bar 平衡杆channel bar 槽钢;槽铁I-bar 工字钢barometer 气压计barrel 桶;筒状物pump barrel 泵缸stuffing box barrel 可拆式填料函体barrier 势垒;障碍物;挡板heat barrier 热障sound barrier 音障thermal barrier 热障;绝热层base 基;底座;支座raised base 加高底座baseline 基准线basin 盆;承盘;水槽;船坞filter basin 过滤池model basin 模型池regulating basin 调节池sedimentation basin 沉淀池settling basin 沉淀池water basin 水池water distribution basin 配水池batch 批bay 间;场;台;隔间;舱;架间erection bay 装配间beam 横杆;梁;束walking beam 摇臂bearing 轴承annular ball bearing 径向球轴承anti-friction bearing 滚动轴承ball/rolling bearing 滚动轴承ball thrust bearing 推力球轴承forced oil lubricated bearing 强制润滑轴承;压力润滑轴承grease lubricated bearing 油脂润滑轴承hydrodynamic bearing 液体动力轴承Michell type thrust bearing 米切尔型推力轴承needle bearing 滚针轴承plain friction bearing 滑动轴承radial ball bearing 径向球轴承radial roller bearing 径向滚柱轴承ring lubricating bearing 油环轴承ring oiling bearing 油环轴承rolling contact bearing 滚动轴承rubber bearing 橡胶轴承sleeve bearing 滑动轴承sliding bearing 滑动轴承spherically mounted thrust bearing 球面推力轴承thrust bearing 推力轴承thrust roller bearing 推力滚柱轴承tilting pad axial thurst bearing 斜垫轴向推力轴承water lubricating bearing 水润滑轴承beat 脉动;偏摆;敲击;跳动bed 床;台;垫;机座;地基test bed 试验台testing bed 试验台bedplate 底座;台板cast bedplate 铸造式底座fabricated bedplate 结构式底座;焊接式底座behaviour 性状;特性;性能;行为behaviour of boundary layer 边界层性能transient behaviour 瞬态特性bell 钟;圆锥状物;锥形口;喇叭管;罩suction bell 吸入锥管;喇叭管bell-mouth 喇叭管bellows 膜盒;波纹管protecting bellows 皱褶式保护盒bench 工作台;架bend 弯头;弯曲delivery bend 吐出弯管discharge bend 吐出弯管normal bend 直角弯管pipe bend 弯管return bend U形管bender 弯曲机pipe bender 弯管机tube bender 弯管机bending 弯曲benzene 苯benzine 汽油;石脑油;挥发油;BFW 锅炉给水bicarbonate 碳酸氢盐;重碳酸盐ammonium bicarbonate 碳酸氢铵;重碳酸铵sodium bicarbonate 碳酸氢钠;重碳酸钠;小苏打bichromate 重铬酸盐potassium bichromate 重铬酸钾bimetal 双金属binder 粘结剂;结合件;夹子bisulfide 二硫化物carbon bisulfide 二硫化碳blade 片;叶片adjustable blade 可调叶片back blade 背叶片cambered blade 弯曲叶片detachable blade 可拆式叶片fixed blade 固定式叶片guide blade 导叶impulse blade 冲击式叶片2005-12-9 14:54:00 中国泵阀联盟预祝您新年新红火xingguang等级:贵宾威望:2文章:847积分:2223门派:无门无派注册:2005年11月16日第 4 楼-------------------------------------------------------------------------------- infinitely thin blade 无限薄叶片s-shaped blade S形叶片stationary blade 固定式叶片three dimensional blade 空间叶片;三维叶片twisted blade 扭曲叶片bleeding 排水bland 混合物blistering 起泡block 块;部件;闭锁;滑车;号码;闭塞pulley block 滑车组pump cylinder block 泵缸体star-shaped cylinder block 星形缸体board 板;台bench board 操纵盘(台)control board 操纵盘(台)body 物体;壳体elastic body 弹性体piston body 活塞体pump body 泵体valve body 阀体boiling 沸腾bolt 螺栓;杆柱anchor bolt 地脚螺栓foundation bolt 地脚螺栓jack bolt 起重螺栓lifting bolt 起重螺钉ring bolt 吊环螺钉spacer bolt 支撑螺栓stud bolt 双头螺栓through bolt 贯穿螺栓tie bolt 拉紧螺栓bolt-hole 螺栓孔book 书hand book 手册boom 构架;桁;超重吊杆;超重臂booster 助力器;升压器;助推器axial flow booster 轴流增压器suction booster 吸入增压器boss 轮毂;凸起部boundary 边界fluid boundary 流体边界bowl 碗;杯;筒;壳体;滚球discharge bowl 导流壳propeller bowl 轴流泵叶轮室stator bowl 定子壳box 箱;盒;外壳;方块(表示一个逻辑单元)bearing box 轴承体;轴承箱distributing box 配电柜distribution box 配电柜gear box 齿轮箱;变速箱packing box 填料函体separate stuffing box 可拆式填料函体speed box 变速箱speed change box 变速箱still box 静水室stilling box 静水室stuffing box 填料函体valve box 阀箱brace 加强筋;手摇曲柄钻;大括弧bracing 支撑;拉条bracket 托架;支架;括弧bearing bracket 轴承架pump bracket 泵托架pump bearing bracket 泵轴承支架sliding bracket 滑动支架brake 制动器;刹车;制动;闸hydraulic brake 水力制动器;液压制动器braking 制动;刹车brand 标记;商标;牌号brass 黄铜nickel brass 镍黄铜breaker 断路器;破碎机air circuit breaker 空气开关;空气自动断路器siphon breaker 虹吸破坏装置vacuum breaker 真空破坏装置breaking 中断;破裂breather 通气阀;呼吸器brine 盐水bronze 青铜aluminium bronze 铝青铜arsenic bronze 砷青铜lead bronze 铅青铜leaded bronze 铅青铜manganese bronze 锰青铜nickel bronze 镍青铜phosphor bronze 磷青铜silicon bronze 硅青铜Silzin bronze 西尔津合金bubble 气泡;磁泡air bubble 空气泡gas bubble 气泡;vapour bubble 蒸汽泡bubbling 起泡bucket 吊桶;勺斗valve type bucket 阀式活塞buoy 浮标conical buoy 锥形浮标buoyance 浮力burr 毛刺;飞边;垫圈bush 衬套bearing bush 轴承衬(套)diaphragm bush 卸压套guide bush 导向衬套interstage bush 级间衬套labyrinth bush 迷宫衬套locating bush 定位套neck bush 轴颈套;填料衬套screwed connector bush 螺纹连接套stuffing box neck bush 填料箱衬套;填料垫throttling bush 节流衬套;卸压衬套bushing 衬套;轴套bearing bushing (U.S.A)轴承衬套pressure reducing bushing (U.S.A)卸压套stuffing box bushing (U.S.A)填料衬套butane 丁烷button 钮;按钮;旋钮by-pass 旁通管cable 电缆;钢索armoured cable 铠装电缆shielded(-conductor) cable 屏蔽电缆underground cable 地下电缆cage 笼;盒;罩seal cage 水封环;灯笼环valve cage 阀箱water seal cage 水封环;calculation 计算performance calculation 性能计算calculator 计算机;计算图表calculus 演算;微积分calculus of variations 变分法callipers 卡钳;测径器calorimeter 量热计cam 凸轮camber 弯度;曲度;曲面;弧vane camber 叶片弯度camera 摄影机;照像机high-speed camera 高速摄影机moving picture camera 电影摄影机can 屏蔽套;罐;壳screening can 屏蔽套shielding can 屏蔽套canal 流道cant 斜面cantilever 悬臂梁;悬臂cap 盖;帽;罩hub cap 轮毂罩;导水锥safety cap 安全罩sand cap 防砂盖threaded cap 螺纹盖tightening cap 压紧盖capacity 容量;流量;功率absorption capacity 吸收能力discharge capacity 吐出流量design capacity 设计流量flow capacity 吐出流量;过流能力large capacity 大流量little capacity 小流量plant capacity 设备容量rated capacity 额定容量reservoir capacity 贮水池容量specific capacity 比流量specified capacity 名义流量unit capacity 单位流量capillarity 毛细管现象carbide 碳化物carbonate 碳酸盐sodium carbonate 碳酸钠carrier 托架;支持物;载体;运载工具bearing carrier 轴承座2005-12-9 14:54:00 新鲜出炉-点击查看简明泵阀词典 xingguang等级:贵宾威望:2文章:847积分:2223门派:无门无派注册:2005年11月16日第 5 楼-------------------------------------------------------------------------------- valve carrier 阀座cartridge 座;心子;筒;单元存储器bearing cartridge 轴承衬套cascade 叶栅;栅;级;串、串联cascade of blade 叶栅;栅;级;串联finite cascade 叶栅case 有限叶栅bottom case 箱;柜;框;架;盒;罩;情况shielding case 下壳casing 保护罩casing of side channel pump 壳体;盒;套;包装casing with transfer passages 侧流道泵壳;旋涡泵泵体annular casing 侧流道泵壳;旋涡泵泵体circular casing 环形壳体;环形压水室delivery casing 上壳(井泵);吐出段discharge casing 上壳(井泵);吐出段gear casing 齿轮箱stage casing 中段泵壳;中段stage casing with bleed off 有抽关的中段suction casing 吸入室(壳)前段volute casing 涡形体;涡壳casting 铸件;铸造chill casting 冷硬铸件compression casting 压铸(件)die casting 压铸件;压铸法gravity die casting 压铸件;重力压铸法pressure casting 压铸steel casting 铸钢casualty 事故;损坏catalog(ue) 目录;一览表catcher 收集器;捕捉器;制动装置dust catcher 除尘器grease catcher 脂油收集器oil catcher 集油器(盘)cathode 阴极cavitation 汽蚀initial cavitation 初生汽蚀cavity 空腔vortex cavity 旋涡区celluloid 赛璐珞cementite 渗碳体;碳化三铁centering 定心;中心调整centi-bar 厘巴(压力测量单位)centistokes 厘斯托克斯;厘沲(运动粘度单位)中心centre 中心centre of curvature 曲率中心centre of mass 质量中心dead centre 死点;滞点centreline 中线;中心线ceramics 陶瓷chain 链;系统driving chain 传动链chair 座位;椅pipe chair 管托chamber 室air chamber (空气)室balancing chamber 平衡室bearing cooling chamber 轴承冷却室dust chamber 除尘器gas-separation chamber 气体分离室high pressure chamber 高压腔overflow chamber 溢流室still-water chamber 静水室suction chamber 吸入室volute chamber 涡室chamfer 倒角;槽;倒圆chamfret 倒角;倒圆channel 渠道;流道;管道;风洞channel of approach 吸水流道approach channel 吸水流道contracted channel 收缩流道contracting channel 收缩流道convergent-divergent channel 收缩-扩散流道curved channel 弯曲流道divergent channel 扩散流道driving channel 引水渠道expanded channel 扩散流道headrace channel 引水渠道open channel 明渠spiral channel 涡形道vane channel 叶片间流道vaned return channel 叶片式反向流道varying area channel 变截面流道characteristic 特性(曲线)cold performance characteristics 冷态特性曲线combined characteristic 综合特性曲线complete characteristic 全性能曲线discharge characteristic 流量特性dropping characteristic 下降特性dynamic characteristic 动力特性external characteristic 外特性friction(al) characteristic 摩擦特性hot performance characteristic 热态特性曲线internal characteristic 内特性metering characteristics of nozzle 喷嘴的流量特性reverse speed characteristic 反转特性shut-off characteristic 关死特性surge characteristic 波动特性;冲击特性system characteristic 管路系统特性transient characteristic 瞬态特性;过滤特性zero torque characteristic 零转矩特性曲线chart 图表alignment chart 诺模图;列线图表conversion chart 换算图表flow chart 程序框图;框图nomographic chart 诺模图;列线图viscosity correction chart 粘度修正图check 检查;防止chest 柜;室;盒;箱high pressure chest 高压腔steam chest 蒸汽室valve chest 阀箱chlorate 氯酸盐calcium chlorate 氯酸钙potassium chlorate 氯酸钾sodium chlorate 氯酸钠chloride 氯化物ammonium chloride 氯化铵barium chloride 氯化钡calcium chloride 氯化钙magnesium chloride 氯化镁polyvinyl chloride 聚氯乙烯potassium chloride 氯化钾sodium chloride 氯化钠chlorobenzene 氯苯chloroform 氯仿;三氯甲烷chloronorgutta 聚氯丁烯;氯丁橡胶chord 弦;弦长mean blade chord 叶片平均翼弦wing chord 翼弦chromate 铬酸盐sodium chromate 铬酸钠chroming 镀铬chronometer 计时器churning 造涡;涡度;涡流形成circlip 弹性卡环;锁紧环;弹性锁紧环circuit 回路;循环;流程closed circuit 封闭回路;闭式回路cold test circuit 冷态试验回路hydraulic circuit 液压回路;液压系统short circuit 短路test circuit 试验回路circulation 环量;环流;循环forced circulation 强迫环流ideal circulation 理想环流secondary circulation 二次环流;次级环流circumfluence 绕流;回流;环流cistern 水箱;水槽water cistern 水箱cladding 敷层;镀层clamp 卡头;夹板;夹钳clap 敲击class 级;类;等级accuracy class 精度等级classification 分类claw 爪;把手;齿adjusting claw 调整爪cleaning 清理2005-12-9 14:55:00 中国泵阀联盟——中国最大的网上泵阀民间团体xingguang等级:贵宾威望:2文章:847积分:2223门派:无门无派注册:2005年11月16日第 6 楼--------------------------------------------------------------------------------clearance 游隙;间隙;许可证axial clearance 轴向间隙running clearance 运转间隙working clearance 运转间隙clearing 清除;消除clearing of fault 故障排除clock 钟表clogging 堵塞clutch 离合器dog clutch 爪形离合器jaw clutch 爪形离合器pawl clutch 爪形离合器ratch(et) 爪形离合器coat 涂敷;镀;涂层;镀层first coat 底漆coating 涂层;包覆层metallic coating 金属包覆(镀层)protective coating 保护涂层cock 旋塞;开关air release cock 放气旋塞drain cock 放水旋塞;排水开关injection cock 注水旋塞pet cock 小活栓;小旋塞priming cock 注水旋塞vent cock 排气旋塞code 代码;规范;程序;符号;指令command code 指令码instruction code 指令码test code 试验规范;试验规程coefficient 系数coefficient of contraction 收缩系数coefficient of discharge 流量系数coefficient of expansion 膨胀系数coefficient of friction 摩擦系数coefficient of heat-transfer 传热系数coefficient of nozzle loss 喷嘴损失系数coefficient of resistance 阻力系数coefficient of viscosity 粘性系数area coefficient 面积系数capacity coefficient 流量系数cavitation coefficient 汽蚀系数contraction coefficient 收缩系数conversion coefficient 转换系数correction coefficient 修正系数critical pressure coefficient 临界压力系数discharge coefficient 流量系数drag coefficient 阻力系数dynamic coefficient of viscosity 动力粘性系数efflux coefficient 流出系数;流速系数;出流系数;流量系数expansion coefficient 胀膨系数filter coefficient 过滤系数flow coefficient 流量系数head coefficient 扬程系数induced drag coefficient 诱导阻力系数induction coefficient 诱导系数;感应系数kinematic coefficient of viscosity 运动粘性系数orifice-metering coefficient 流量计系数penetrating coefficient 穿透系数;漏损系数pressure coefficient 压力系数resistance coefficient 阻力系数roughness coefficient 粗糙系数skin-friction coefficient 表面摩擦系数sound-absorption coefficient 吸音系数surface pressure coefficient 表面压力系数temperature coefficient 温度系数thrust(force) coefficient 推力系数transmission coefficient 穿透系数;传导系数transparency coefficient 透明系数viscosity coefficient 粘性系数coil 盘管;线圈;螺(旋)管;蛇形管coincidence 符合;重合;一致collar 圈;环;箍;环状物locating collar 定位缘套loose(shaft) collar 轴肩挡圈protecting collar (U.S.A)轴肩挡圈;防护罩shaft collar 轴肩挡圈thrust collar 止推环collector 收集器dust collector 除尘器oil collector 集油器collision 碰撞;冲击random collision 不规则碰撞;随机碰撞column 柱;列discharge column 扬水柱管liquid column 液柱mercury column 水银柱support column 支承柱管water column 水柱command 指令compensation 补偿clearance compensation 间隙补偿error compensation 误差补偿compensator 胀缩件;补偿器sterting compensator 起动补偿器;起动自耦变压器complex-velocity 复(数)速度component 分量;部件;成分component of force 分力force component 分力normal volocity component 法向分速度;垂直分速度。
阀门专业英语阀门1. 冶金特种阀门metallurgy special valve2. 卫生级设备/配件/阀门sanitary equipment/parts/valve3. 蝶阀butterfly valve4. 闸阀gate valve5. 锻钢阀门forged steel valve6. 进口阀门imported valve7. 球阀ball valve8. 截止阀globe valve9. 止回阀check valve10. 平衡阀balance valve11. 污水过滤器阀门sewage strainer valve12. 液面计liquid indicator13. 外国标准阀门foreign standard valve14. 黄铜阀门brass valve15. 氧气阀门valve for oxygen16. 氨气阀门valve for ammonia gas17. 防腐阀门anticorrosive valve18. 疏水阀steam trap19. 电磁阀solenoid valve20. 排气阀gas bleed valve21. 柱塞阀plunger valve22. 旋塞阀plug valve23. 调节阀control valve24. 减压阀pressure reducing valve25. 隔膜阀diaphragm valve26. 安全阀safety valve27. 石油/天然气阀门Petroleum/natural gas valve28. 水利控制阀门water control valve29. 电动阀门electrically operated valve30. 补偿器/伸缩节compensator/expansion joint31. 切断阀block valve32. 调压阀pressure regulating valve33. 电站阀门power station valve34. 关闭阀shutoff valve35. 泄压\持压阀relief valve36. 控制阀control valve37. 稳压阀voltage-stabilizing valve38. 针型阀needle valve39. 逆止阀non return valve40. 水位阀level valve41. 遥控阀remote valve42. 旋转阀rotary valve43. 二通阀two-way valve44. 管夹阀pinch valve45. 三角阀triangular valve46. 滑阀slide valve47. 单向阀single valve48. 气控阀pneumatic control valve49. 针阀needle valve50. 温控阀temperature control valve51. 混水阀water mixing valve52. 出料阀discharge valve53. 冲洗阀flush valve54. 水暖阀门water heating valve55. 锁阀holding valve56. 视镜sight glass57. 集流阀collecting valve58. 角阀angle valve59. 呼吸阀breather valve60. 仪表阀instrument valve61. 脉冲阀pulse valve62. 高压阀high pressure valve63. 膨胀阀expansion valve64. 转阀rotary valve65. 塑料阀门plastics valve66. 气动阀pneumatic valve67. 暖气阀steam heat valve68. 管子套pipe sleeve69. 平板阀plate valve70. 排渣阀reject valve71. 底阀bottom valve72. 背压阀counterbalance valve73. 切换阀switch valve74. 节流阀throttle valve75. 减压器pressure reducer76. 自动阀automatic valve77. 报警阀alarm valve78. 真空阀vacuum valve79. 棒阀bar valve80. 钛阀门titanium valve81. 高温高压阀门high temperature pressure valve82. 插板阀slider damper83. 百叶阀louver valve84. 放料阀dump valve85. 排污阀sewer valve86. 美标阀门API valve87. 防火阀fire damper88. 瓶阀air bottle valve89. 换向阀direction valve90. 手动阀manual valve91. 油田阀oil field valve92. 燃气阀门gas valve93. 溢流阀over flow valve94. 放水阀water drain valve95. 排水阀drainage valve96. 疏水阀steam trap97. 进水阀inlet valve98. 低压阀low pressure valve99. 排料阀dump valve100. 脉冲阀pulse valve101. 放气阀air escape vale102. 四通阀four way valve103. 操作阀operating valve104. 分配阀distribution valve105. 脚踏阀foot valve106. 放散阀relief valve107. 液压阀hydraulic valve108. 放料阀dump valve109. 阀芯valve core110. 煤气阀门gas valve111. 流量控制阀flow control valve112. 防盗阀burglar valve•驱动装置actuator1. 电动装置electric actuator2. 气动装置pneumatic actuator3. 电动执行机构electrical actuator4. 液压装置hydraulic unit5. 传动装置gear actuator6. 气动执行器pneumatic actuator7. 定位器positioner8. 传感器sensor•密封件seal1. 机械密封件machinery seal2. 油封oil seal3. 密封垫片/圈sealing gasket/sealing washer4. V型组合封V combination seal5. 液压快装接头hydraulic compact joint6. O形圈O ring7. 星形圈star ring8. 密封填料sealing packing9. 柔性石墨填料环flexible graphite packing ring10. 注塑密封件plastic seal11. 密封胶条seal rubber strip12. 聚四氟乙烯制品PTFE product13. 盘根packing14. 橡胶制品rubber product15. 液压密封件hydraulic seal16. 活塞环piston ring17. 导向环rider ring18. 杂件类miscellaneous19. 垫片gasket•管件pipe fittings1. 金属管metallic conduit2. 塑料管plastic piep3. 不锈钢管stainless steel tube4. 软管hose pipe5. 波纹管corrugated pipe6. 胶管rubber tube7. 水封气动封water seal/pneumatic seal8. 钢管steel pipe9. 管道pipe10. 铝管件aluminum pipe fittings11. 铜管件copper pipe fittings•标准件hardware1. 螺栓bolt2. 螺母nut3. 螺钉screw4. 环箍nipping fork5. 弹簧片leaf spring6. 冲压片punch tablet7. 标准紧固件standard fastening piece8. 螺丝screw9. 垫圈washer10. 非标准紧固件off-rating fastening piece11. 螺塞screw plug12. 换热器exchangeability•其它miscellaneous1. 温控器thermostat2. 过滤器strainer3. 法兰flange4. 三通3 way5. 弯头elbow6. 换热器exchangeability7. 千斤顶cylinder8. 轴承bearing9. 阀体body10. 真空机组vacuum set11. 滤芯filter element12. 流量计flowmeter13. 泵阀配件parts for pump & valve14. 标记机marking machine15. 减振器shock reducer16. 喷嘴nozzle17. 接头joint18. 油缸cylinder19. 阻火圈fire retardant ring20. 铸件castings21. 水处理设备water treatment equipment22. 聚乙烯polyethylene23. 压缩机compressor24. 加热器heater25. 其它miscellaneous26. 压力表pressure gauge27. 机床lathe28. 阀门配件valve parts29. 阀门检测设备valve test apparatus。
CQ螺纹球阀CQ Thread Ball ValvesL形三通式L—pattern three wayT形三通式T—pattern three way安全阀Safety valve暗杆闸阀Inside screw nonrising stem type gate valve 百叶窗; 闸板shutter百叶窗式挡板louver damper摆阀式活塞泵swing gate piston pump保温式Steam jacket type报警阀alarm valve报警阀; 信号阀; 脉冲阀sentinel valve背压调节阀back pressure regulating valve背压率Rate of back pressure本体阀杆密封body stem seal波纹管阀Bellows valves波纹管密封阀bellow sealed valve波纹管密封式Bellows seal type波纹管平衡式安全阀Bellows seal balance safety valve 波纹管式减压阀Bellows reducing valve波纹管式减压阀Bellows weal reducing valve薄膜thin film薄膜;隔膜diaphragm薄膜式减压阀Diaphragm reducing valve薄型闸阀Thin Gate Valves不封闭式Unseal type槽车球阀Tank Lorry Ball Valves颤振Flutter常闭式Normally closed type常开式Normally open type超低温阀门Cryogenic valve超高压阀门Super high pressure valve超过压力Overpressure of a safety valve衬胶隔膜阀rubber lined diaphragm衬胶截止阀rubber lined globe valve垂直板式蝶阀Vertical disc type butterfly valve磁耦合截止阀Magnetic Co—operate Globe Valves带补充载荷的安全阀Supplementary loaded safety valve 带辅助装置的安全阀Assisted safety valve单阀碟双面平行密封闸阀parallel single disk gate valve 单口排气阀Single Opening Exhaust Valves单向阀Non—return Valve单闸板Single gate disc单闸板平板闸阀Single Disc Flat Gate Valves弹簧薄膜式减压阀Spring diaphragm reducing valve弹簧式安全阀Direct spring loaded safety valve弹簧座Spring plate弹性闸板Flexible gate disc当量计算排量Equivalent calculated capacity挡板damper导阀Pilot valve导向套Valve guide disc guide低温阀门Sub—zero valve低压阀门Low pressure valve底阀bottom valve底阀Foot valve电磁动装置Eletro magnetic actuator电磁阀magnetic valve电磁阀solenoid valve电磁-液动装置Eletro magnetichydraulic actuator电动阀mortor operated valve电动阀motorized valve电动截止阀Electric Actuated Stop Valves电动平行式双闸板闸板Electric Double Disk Parallel Gate Valves 电动楔式闸阀Electric Actuated Wedge Gate Valves电动装置Electric actuator电-液动装置Eletro hydraulic actuator电液伺服阀electro-hydraulic servovalve调节弹簧Regulation spring调节阀adjusting valve调节阀control valve调节阀regulating valve调节螺套Adjusting bolt Adjusting screw调节圈Adjusting ring蝶板Disc蝶阀;瓣阀butterfly valve蝶阀;瓣阀;拍门;铰链阀flap valve蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式止回阀Butterfly swing check valve定比减压阀Proprutioning pressure reducing valve定差减压阀Fixed differential reducing valve定值减压阀Fixed pressure reducing valve动态特性Dynamic characteristics对焊连接阀Buttwelding valves对夹蝶板阀Wafer plate valves对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning 对夹式阀门Clamp valves对夹式止回阀Wafer Check Valves额定排量Certified capacity额定排量系数Derated coefficient of discharge二通阀Two-way valves阀 valve阀板 valve deck plate阀板 valve plate阀板式活塞泵 valve deck plate type piston pump 阀板式活塞泵 valve plate type piston pump阀瓣 Disc阀操纵杆 valve operating rod阀痤槽 valve seat recess阀挡 valve grid阀挡 valve positioner阀挡 valve stop阀导杆 valve tail rod阀导向器 valve guide阀盖 bonnet阀盖衬套 bonnet bush阀盖垫片 bonnet gasket阀杆 stem阀杆 valve rod阀杆 valve spindle阀杆端部尺寸 Dimmension of valve stem end阀杆环 stem ring阀杆螺母 Yoke bushing Yoke nut阀杆填料 stem packing阀杆头部尺寸 Dimension of valve stem head阀簧 valve spring阀簧压板 valve spring plate阀控水锤泵 valve—controlled hydraulic ram阀框架 valve yoke阀门 Valve阀门传动装置 valve bandle set阀门和管件 Valves and Fittings阀门盘根 valve packing阀门手柄 valve handle阀盘 disc阀盘 valve disc阀片 Disc阀球 valve ball阀驱动臂 valve driving arm阀驱动臂 valve motion arm阀式活塞 valve type piston阀式活塞 valve type bucket阀室式活塞泵 valve box type piston pump阀室式活塞泵(美) valve pot type piston pump阀抬起装置 valve lifting device阀体 body阀体 valve body阀箱 valve box阀箱 valve cage阀箱 valve chest阀箱;阀限位器 valve guard阀箱盖 cover for valve box阀箱盖 valve box cover阀箱式活塞泵(美) turret type piston pump阀形活塞泵 valve type piston pump阀座 Seat ring阀座 valve carrier阀座 valve seat(body seat)阀座;阀盘 valve seat阀座环 seat ring阀座密封嵌条 sealing strip for valve seat法兰 flange法兰堵头 blind flange法兰端 flange end法兰接头 flange joint法兰连接紧固件(双头螺栓和螺帽) flange bolting法兰密封面,法兰面 flange facing法兰面加工 flange facing finish法兰球阀 Flange Ball Valves翻板阀 Flap反冲盘 Disc holder反向作用式减压阀 Reverse acting reducing valve反向作用式减压阀 Reverse acting reducing valve放空阀 emptying valve放气阀 air vent valve;vent valve放气阀;排气阀 air evacuation valve放泄阀 escape valve分置阀室式活塞泵 separate valve box type piston pump 分置阀室式活塞泵(美) side pot type piston pump封闭式 Seal type浮动式球阀 Float ball valve浮球 Ball float浮球阀 Float Valve浮球式疏水阀 Ball float steam trap浮球式疏水阀 Free Float Type Steam Trap浮桶 Bucket float浮桶式疏水阀 Open bucket steam trap辅助(副)阀 Auxiliary valves负荷率 Rate of load condensate附加背压力 Superimposed back pressure复位弹簧 Returnning spring杠杆式 Lever type杠杆式安全阀 Lever and weight loaded safety valve 杠杆式减压阀 Lever reducing valve高温阀门 High temperature valve高压阀门 High pressure valve格兰密封 gland隔离阀 isolating valve隔膜Diaphragm隔膜阀diaphragm valve隔膜式控制阀diaphragm operated comtrol valve工作背压Operating back pressure工作温度Operating temperature工作温度Working temperature工作压差Operting differential pressure工作压力Operating pressure工作压力Working pressure公称通径Nominal diameter公称压力Nominal pressure固定式球阀Fixed ball valve关闭压力Lockup pressure关阀过冷度Subcooled temperature of close valve关阀温度Closing valve temperature管道安全阀Piping Safety Valves过冷度Subcoold temperature过流阀(或节流阀)Restrictor Valves喉径Throat diameter滑阀slide valve滑阀式回转活塞泵rotary piston pump with slide gate 滑阀型转子泵eccentric rotary pump with sliding sleeve 环形阀annular valve环形阀double beat valve换向阀selector valve换向阀shuttle valve回转滑阀活塞泵piston pump with rotary gate回座压力Re—seating pressure of a safety valve活塞昵减压阀Piston reducing valve活塞式阀piston valve活塞式阀;柱塞式阀plunger valve活塞式减压阀Piston reducing valve减速阀Deceleration valves减压比Pressure reducing ratio减压阀pressure reducing valve浆液阀Parallel Slide Valves角阀Angle Valve角阀isolation valve angle configuration角式Angie type角式节流阀Angle Throttle Valves角式截止阀Angle Stop valves铰链阀;片状阀flapper valve节流阀throttle valve节流阀choke valve节流阀;节流throttle结构长度Face—to-face dimension ;End-to—end dimension;Face—to—centre dimension 结构形式Type of construction截止阀Globe valve截止阀Shut-off Valve截止阀;关断阀shut—off valve截止式隔膜阀Globe diaphragm valve紧急切断阀Emergeny Cut-off Valves进气阀air intake valve进水阀;进口阀门inlet valve静态特性Static characteristics静态特性偏差Static characteristics derivation开阀过冷度Subcooled temperature of open valve开阀温度Opening valve temperature开启高度Lift壳体试验Shell test壳体试验压力Seal test pressure空气阀门Air valves快速排污阀Quick Draining Valves类型Type冷凝结水排量Cold condensate capacity冷态试验差压力Cold differential test pressure理论排量Theoretical flowing capacity连接槽尺寸Dimension of connecting channel连接尺寸Conncetion cimension连接形式Type of connection帘面积Curtain area流道面积Flow area流道直径Flow diameter流量孔板flow orifice plate流量控制阀flow control valve流量特性Flow characteristics流量特性偏差Flow characteristics derivation漏汽量Steam loss脉冲式疏水阀Impulse steam trap密封面Sealing face密封试验Seal test密封试验压力Seal test pressure明杆平行式双闸板闸板Double Disk Parallel Gate Valves明杆闸阀Outside screw stem rising through handwheel type gate valve 膜片Diaphragm内压自封Pressure seat逆止阀;止回阀check valve逆止阀;止回阀non-return valve逆止阀;止回阀;单向阀check valve排放背压力Brilt-up back pressure排放压力Relieving pressure排灰阀Ash valves排量系数Coefficient of discharge排气阀air release valve排气阀Exhaust valves排气阀Vent Valve排水阀Drainage valves排水温度Temperature at discharging condensate排污阀blowdown valve排污箱(阀) Waste Valves排渣闸阀Scum Gate Valves盘阀moushroom valve盘状阀plate valve旁路阀by pass valve配汽活塞阀缸套piston valve line喷射阀injection valve喷射阀sprayer valve喷水阀spray water valve频跳Chatter平衡阀Balance valves平衡式Balance type平行式闸阀Parallel gate valve Parallel slide valve启闭件Disc启闭压差Blowdown of a safety valve起始升程Commencement of lift气动装置Pneumatic actuator气阀摇臂valve arm气-液动装置Pneumatic—hydraulic actuator潜水电泵(排污泵)Submerged Motor Pumps切断阀;截止阀block valve;shut—off valve;stop valve切断式止回阀stop check valve切换阀;多向阀changeover valve球、球芯Ball球阀Ball valve球阀globe valve球体Ball全启式安全阀Fall lift safety valve热凝结水排量Hot condensate capacity入口隔离门suction isolating valve塞子Plug三通阀three-way isolating valve三通阀three—way valve三通式Three way type上密封Back seat上密封试验Back seal test渗漏量Leckage升降立式止回阀Vertical lift check valve升降式止回阀Lift check valve适用介质Suitable medium适用温度Suitable temperature手摇油泵(阀) Manual Oil Pumps Valves疏水阀drain valve双金属片式疏水阀Bimetal elements steam trap双口排气球Double Opening Exhaust Valves双联弹簧式安全阀Duplex safety valve双闸板Double gate disc双闸板平板闸阀Double Disc Flat Gate Valves水封闸阀Water Seal Gate Valves水力喷射器(真空泵) Vacuum Pumps伺服阀servovalve填料Packing填料垫Packing seat填料函Stuffing填料式旋塞阀Gland packing plug valve填料箱Stuffing box填料压盖Gland通气阀breather valve通气阀;呼吸器breather通用阀门General valve吐出阀;排出阀discharge valve吐出阀限位器delivery valve guard微启式安全阀Low lift safety valve微阻缓闭止回阀Tiny Drag Slow Shut Check Valves 吻合度Percent of contact area蜗轮传动蝶阀Butterfly Valves with Gear Actuator蜗轮传动装置Wormgear actuator屋脊式隔膜阀Weir diaphragm valve无阀泵valveless pump无阀隔膜泵valveless diaphragm pump无阀振动泵valveless vibration pump无负荷漏汽量No—load steam loss无负荷漏汽率Rate of no-load steam loss吸(抽)气阀Aspirating valves吸入阀suction valve吸入阀限位器suction valve guard先导式安全阀Pilot operated safety valve先导式液压阀Pilot—operated reducing valve相对静偏差Relative static characteristics derivation相对流量特性偏差Relative flow characteristics derivation相对压力特性偏差Relative pressure characteristics derivation 销轴Hinge pin楔式闸阀Wedge gate valve斜板式蝶阀Indined disc butterfly valve泄料(放空,排污)阀Blowdown valves泄压阀Decompression valves泄压阀pressure release valve泄压阀;安全阀relief valve卸荷式减压阀Balanced reducing valve型号Type Model旋启多瓣式止回阀Multi—disc swing foot valve旋启式止回阀Swing check valve旋启双瓣式底阀Double disc swing foot valve旋塞阀Cock旋塞阀plug valve压力(増压)阀Pressure valve压力调节阀;压力控制阀pressure controlled valve压力特性Pressure characteristics压力特性偏差Pressure characteristics derivation压力增长系数Pressure increasing ratio摇杆Arm液动装置Hydraulic actuator液化气管件LPG Pipe Fitting液下泵Under Water Pumps液压执行器hydraulic actuator仪表针形截止阀Meter Needle Type Globe Valves溢流阀overflow valve翼形阀;锥形阀wing valve油封式旋塞阀Lubricated plug valve有阀翼板double acting wing有阀翼板wing with valve有负荷漏汽量Load steam loss有负荷漏汽率Rate of load steam loss圆板阀;圆盘阀disc valve圆盘式疏水阀Shemostatic team trap圆柱齿轮传动装置Cylindrical gear actuator圆锥齿轮传动装置Conical gear actuator闸板Wedge disc闸板式隔膜阀Wedge diaphragm valve闸阀gate valve闸阀sluice valve针形阀Pintle valve ; Needle valve真空破坏阀vacuum breaker valve蒸汽疏水阀Automatic steam trap Trap整定压力Set pressure正向作用式减压阀Direct acting reducing valve 支架Yoke直接载荷式安全阀Direct loaded safety valve直接作用式减压阀Direct—acting reducing valve 直流式Y—globe type直流式截止阀Oblique Stop Valve直通单向阀inline check valve直通单向阀straightway check valve直通阀Throughway Valve止回阀Check Valve止回阀;回流阀reflux valve制动阀Brake valves中压阀门Middle pressure valve钟形浮子式疏水阀Inverted bucket steam trap 钟形罩Inverted bucket轴套Axis Guide主阀Main valve主要外形尺寸Prime out—form dimensions主要性能参数Specifeca tion speeification注液漏斗阀Priming Tundish Valve柱塞阀Plunger valve柱塞截止阀Plunger Globe Valve柱塞型摆动阀rocking plunger valve撞击手轮Impact handwheel锥形阀;翼形阀conical valve自动循环阀Automatic Recirculation Valve组合阀Combination valves最大过冷度Maximum subcoold temperature最大流量Maximum flow rate最大压差Maximum differential pressure最低工作压力Minimum operating pressure最高背压率Maximum rate of back pressure最高工作背压Maximum operating back pressure最高工作温度Maximum operating temperature最高工作压力Maximum operating pressure最高排水温度Maximum temperature at discharging 最高允许温度Maximum allwable temperature最高允许压力Maximum allowable pressure最小过冷度Minimum subcooled temperature最小压差Minimum differntial pressure。
各种阀门的翻译(All kinds of valves Chinese Translation)Man without instrument will never die. Energy-saving there, life rarely live to seventy. The Tong flower ten thousand Li Dan mountain road, the young chicken is clear in the old Feng voice. The spring grass grows, Liu changed songbirds park. Better a book without a book. All kinds of valve English translationValve valve <BR>Valve plate valve, deck, plate, <BR>Valve plate valve, plate, <BR>Valve plate type piston pump valve, deck, plate, type, piston, pump, <BR>Valve plate type piston pump, valve, plate, type, piston, pump, <BR>Disc Disc <BR>Valve lever valve, operating, rod, <BR>Valve seat recess <BR> slot valve acneValve block valve, grid, <BR>Valve block valve, positioner, <BR>Valve block valve, stop, <BR>Valve guide rod valve, tail, rod, <BR>Valve guide valve, guide, <BR>Valve cover bonnet <BR>Bonnet Bush bonnet Bush <BR>Bonnet gasket bonnet, gasket, <BR>Valve stem stem <BR>Valve stem valve, rod, <BR>Valve stem valve, spindle, <BR>Stem end dimensions Dimmension, of, valve, stem, end, <BR> Stem ring stem, ring, <BR>Stem nut Yoke, bushing, Yoke, nut, <BR>Stem packing stem, packing, <BR>Stem head dimensions Dimension, of, valve, stem, head, <BR> Valve spring valve, spring, <BR>Valve spring plate valve, spring, plate, <BR>Valve controlled water hammer pump valve-controlled, hydraulic, ram, <BR>Valve frame valve, yoke, <BR>Valve Valve <BR>Valve drive valve, bandle, set, <BR>Valves and fittings Valves, and, Fittings, <BR>Valve packing valve, packing, <BR>Valve handle valve, handle, <BR>Valve disc disc <BR>Valve disc valve, disc, <BR>The valve plate is Disc <BR>Valve ball valve, ball, <BR>Valve drive arm valve, driving, arm, <BR>Valve drive arm valve, motion, arm, <BR>Valve type piston valve, type, piston, <BR>Valve type piston valve, type, bucket, <BR>Valve chamber type piston pump, valve, box, type, piston, pump, <BR>Valve chamber type piston pump (beauty) valve, pot, type, piston, pump, <BR>Valve lifting device valve, lifting, device, <BR>Valve body body <BR>Valve body valve, body, <BR>Valve box valve, box, <BR>Valve box valve, cage, <BR>Valve box valve, chest, <BR>Valve box, valve limiter, valve, guard, <BR>Valve case cover cover for valve box <BR>Valve case cover valve, box, cover, <BR>Pump turret type piston <BR>Valve piston pump valve type piston pump <BR>Seat Seat, ring, <BR>Seat valve, carrier, <BR>Seat valve seat (body seat) <BR>Valve seat; disc valve seat <BR>Seat ring seat, ring, <BR>Sealing strip for valve seat sealing strip seatFlange flangeFlange plug blind flangeFlange end flange endFlange joint flange jointFlanges, fasteners (studs and nuts) flange, bolting Flange sealing surface, flange face flange facing Flange processing flange, facing, finishFlanged ball valve Flange, Ball, ValvesTilting plate valve FlapRecoil disk Disc holderReverse acting pressure reducing valve Reverse, acting, reducing, valveReverse acting pressure reducing valve Reverse, acting, reducing, valveVent valve emptying valveBleeder valve air, vent, valve; vent valveVent valve; exhaust valve air, evacuation, valveDrain valve escape, valveSplit valves, chamber type piston pumps, separate, valve, box, type, piston, pumpSplit valve, chamber type piston pump (beauty), side, pot, type, piston, pumpClosed Seal typeFloating ball valve Float, ball, valveFloat, Ball, floatFloat valve Float ValveBall float, trap, steam, float trapFree Trap, Float, Type, Steam, floatPontoon Bucket floatOpen bucket steam trapAuxiliary (sub) valve Auxiliary, valvesLoad rate Rate, of, load, condensateAdditional back pressure Superimposed, back, pressureReset spring Returnning springLever type Lever typeLever type safety valve Lever, and, weight, loaded, safety, valveLever relief valve Lever, reducing, valveHigh temperature valve High, temperature, valveHigh pressure valve High, pressure, valveGran sealed glandIsolation valve isolating valveDiaphragm DiaphragmDiaphragm valve diaphragm valveDiaphragm type control valve diaphragm, operated, comtrol,valveWork back pressure Operating back pressureOperating temperature Operating temperatureOperating temperature Working temperatureOperating pressure difference Operting, differential, pressureThe work pressure is Operating pressureThe work pressure is Working pressureNominal diameter Nominal diameterNominal pressure Nominal pressureFixed ball valve Fixed, ball, valveTurn off the pressure Lockup pressureTurn off valve subcooling Subcooled, temperature, of, close, valveTurn off valve temperature Closing, valve, temperaturePipeline safety valve Piping, Safety, ValvesUndercooling Subcoold, temperatureOvercurrent valve (or throttling valve) Restrictor ValvesThroat diameter Throat diameterSpool slide valveSlide valve type rotary piston pump, rotary, piston, pump, with, slide, gateSpool valve type rotor pump eccentric, rotary, pump, with, sliding, sleeveRing valve annular valveRing valve double, beat, valveReversing valve selector valveReversing valve shuttle valveRotary slide piston pump piston, pump, with, rotary, gate回座压力回座压力安全阀活塞昵减压阀活塞式减压阀活塞式阀活塞阀活塞式阀;柱塞式阀柱塞阀活塞式减压阀活塞式减压阀减速阀减速阀减压比减压比减压阀减压阀浆液阀平行滑动阀角阀角阀角阀隔离阀角度配置角式安吉型角式节流阀角式节流阀角式截止阀直角截止阀铰链阀;片状阀挡板阀节流阀节流阀节流阀节流阀节流阀;节流节流结构长度面对面尺寸;端到端的尺寸;面对中心尺寸结构形式型建筑截止阀截止阀截止阀关闭阀截止阀;关断阀切断阀截止式隔膜阀截止式隔膜阀紧急切断阀紧急切断阀进气阀进气阀进水阀;进口阀门进水阀静态特性静态特性静态特性偏差静态特性偏差开阀过冷度开阀过冷度开阀温度开阀温度开启高度电梯壳体试验壳体试验壳体试验压力密封试验压力空气阀门空气阀快速排污阀快速排污阀类型型冷凝结水排量冷凝力冷态试验差压力冷试验压差理论排量理论流量连接通道连接槽尺寸尺寸连接尺寸连接维连接形式连接类型帘面积帘面积流道面积流区流道直径流径流量孔板流量孔板流量控制阀流量控制阀流量特性流动特性流量特性偏差流量特性偏差漏汽量蒸汽损失脉冲式疏水阀脉冲式蒸汽疏水阀密封面密封面密封试验密封试验密封试验压力密封试验压力明杆平行式双闸板闸板平行式双闸板闸阀明杆闸阀外螺纹截止阀升降杆式闸阀膜片隔膜内压自封压座逆止阀;止回阀止回阀逆止阀;止回阀止回阀逆止阀;止回阀;单向阀止回阀排放背压力brilt背压力排放压力缓解压力排灰阀灰阀放电排量系数系数排气阀空气释放阀排气阀排气阀排气阀排气阀排水阀排水阀排水温度排冷凝温度排污阀排污阀排污箱(阀)废物的阀门排渣闸阀排渣闸阀盘阀moushroom阀盘状阀板阀旁通阀旁路阀配汽活塞阀缸套活塞阀线喷射阀喷射阀喷射阀喷雾阀喷水阀喷水阀频跳颤振平衡阀平衡阀平衡式平衡式平行式闸阀平行闸阀平行滑动阀启闭件盘启闭压差排污安全阀起始升程开始提升气动装置气动执行器气阀摇臂阀臂气-液动装置液压气动执行器潜水电泵(排污泵)潜水电泵切断阀;截止阀截止阀;截止阀;截止阀切断式止回阀截止止回阀切换阀;多向阀转换阀球、球芯球球阀球阀球阀截止阀球体球全启式安全阀全启式安全阀热凝结水排量热凝力入口隔离门吸气截止阀塞子插头三通阀三隔离阀三通阀三通阀三通式三式上密封后座上密封试验密封试验渗漏量漏升降立式止回阀立式升降式止回阀升降式止回阀升降式止回阀适用介质适用介质适用温度适宜温度手摇油泵(阀)手摇油泵疏水阀排水阀双金属片式疏水阀蒸汽疏水阀双金属元件双口排气球双口排气阀双联弹簧式安全阀双安全阀双闸板双闸板双闸板平板闸阀双闸板平板闸阀水封闸阀水密封闸阀水力喷射器(真空泵)真空泵伺服阀伺服阀填料包装填料垫填料座填料函馅填料式旋塞阀填料式旋塞阀填料箱填料箱填料压盖腺通气阀呼吸阀通气阀;呼吸器呼吸通用阀门通用阀门吐出阀;排出阀排放阀吐出阀限位器输送阀保护微启式安全阀低压安全阀微阻缓闭止回阀微阻缓闭止回阀吻合度%的接触面积蜗轮传动蝶阀蝶阀蜗轮传动蜗轮传动装置蜗轮驱动器屋脊式隔膜阀堰式隔膜阀无阀泵无阀泵无阀隔膜泵无阀隔膜泵无阀振动泵无阀泵振动无负荷漏汽量无负荷漏汽无负荷漏汽率无负荷漏汽率吸(抽)气阀吸气阀吸入阀吸入阀吸入阀限位器吸入阀保护先导式安全阀先导式安全阀先导式液压阀先导式减压阀相对静偏差相对静态特性偏差相对流量特性偏差相对流量特性偏差相对压力特性偏差相对压力特性偏差销轴铰链销楔式闸阀楔式闸阀斜板式蝶阀倾斜盘蝶阀泄料(放空,排污)阀排污阀泄压阀减压阀泄压阀压力释放阀泄压阀;安全阀溢流阀卸荷式减压阀平衡阀型号型模型旋启多瓣式止回阀多盘摆动脚阀旋启式止回阀旋启式止回阀旋启双瓣式底阀双瓣旋启式脚踏阀旋塞阀旋塞旋塞阀旋塞阀压力(増压)阀压力阀压力调节阀;压力控制阀压力控制阀压力特性压力特性压力特性偏差压力特性偏差压力增长系数压增长率摇杆臂液动装置液压执行机构液化气管件液化石油气管道配件水下泵液下泵液压执行器液压执行机构仪表针形截止阀仪表针型截止阀溢流阀溢流阀翼形阀;锥形阀翼阀油封式旋塞阀润滑旋塞阀有阀翼板双动翼有阀翼板翼阀有负荷漏汽量负荷漏汽有负荷漏汽率有负荷漏汽率圆板阀;圆盘阀盘阀圆盘式疏水阀圆盘式疏水阀圆柱齿轮传动装置圆柱齿轮传动装置圆锥齿轮传动装置圆锥齿轮传动装置闸板闸板闸板式隔膜阀截止式隔膜阀闸阀闸阀闸阀闸阀针形阀针阀;针形阀真空破坏阀真空断路阀蒸汽疏水阀自动蒸汽陷阱陷阱整定压力设定压力正向作用式减压阀直接作用式减压阀支架轭直接载荷式安全阀直接载荷式安全阀直接作用式减压阀直接作用式减压阀直流式缩喉管Y球形型直流式截止阀斜截止阀直通单向阀内置止回阀直通单向阀直通单向阀直通阀直通阀止回阀止回阀止回阀;回流阀回流阀制动阀制动阀中压阀门中压阀门钟形浮子式疏水阀倒吊桶式疏水阀钟形罩倒吊桶轴套轴导主阀主阀主要外形尺寸主要外形尺寸主要性能参数specifeca等speeification 注液漏斗阀启动包阀柱塞阀柱塞阀柱塞截止阀柱塞截止阀柱塞型摆动阀摇摆柱塞阀撞击手轮冲击手轮锥形阀;翼形阀锥形阀自动循环阀自动再循环阀组合阀组合阀最大过冷度最大subcoold温度最大流量最大流量最大压差最大压差最低工作压力最低工作压力最高背压率最大背压率最高工作背压最高工作背压最高工作温度最高工作温度最高工作压力最大操作压力最高排水温度最高温度在卸货最高允许温度最大允许温度最高允许压力最大允许压力最小过冷度最低过冷温度最小压差最小差压力千淘万漉虽辛苦,吹尽狂沙始到金。
阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸(抽)气阀Auxiliary valves 辅助(副)阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料(放空,排污)阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀 Butterfly Valves with Gear Actuator 蜗轮传动蝶阀 Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀 Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气阀Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀 Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀)Meter Needle Type Globe Valves 仪表针形截止阀 Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力(増压)阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀)Safety Valves 安全阀 Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀 Single Opening Exhaust Valves 单口排气阀Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀 Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵)Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质 Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰 Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity 材料化学成份和机械性能materials 材料 Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座,密封面Seat testing pressure 压力气密封试验压力 Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力 Steam , condensate 蒸汽,凝结水Stroke 冲程,行程Water,oil,steam 水,温度,气Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜 Ceramic metal 陶瓷金属 Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢 Chromium-molybdenum steel 铬钼钢 Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯 Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀 Ash valves 排灰阀Aspirating valves 吸(抽)气阀Auxiliary valves 辅助(副)阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料(放空,排污)阀 Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀 Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球 Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀 Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves 电动平行式双闸板闸板 Emergeny Cut-off Valves 紧急切断阀 Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀 Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀 High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀 Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀 Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀) Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀 Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵 Plunger valves 柱塞阀Pressure valve 压力(増压)阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀 Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵 Scum Gate Valves 排渣闸阀Air valves 空气阀门 Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀 Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀 Aspirating valves 吸(抽)气阀Auxiliary valves 辅助(副)阀 Balance valves 平衡阀Bellows valves 波纹管阀 Blowdown valves 泄料(放空,排污)阀Brake valves 制动阀 Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀 Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门 Cock 二通Combination valves 组合阀 CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀 Deceleration valves 减速阀Diaphragm Valves 隔膜阀 Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀 Double Disk Parallel Gate Valves明杆平行式双闸板闸板 Double Opening Exhaust Valves 双口排气球 Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀 Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板 Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀 Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀 Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀 Gauge Valves 仪表阀Hand-operated valves 手动阀 Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀 Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀 Limit valves 限位阀Lining Ball Valves 衬里球阀 Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀 Lining Cock 衬里二通Lining Globe Valves 衬里截止阀 Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计 LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀 Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀) Meter Needle Type Globe Valves 仪表针形截止阀 Oblique Stop Valves 直流式截止阀 Parallel Slide Valves 浆液阀Pintle valve 针形阀 Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀 Pressure valve 压力(増压)阀Piping Pumps 管道泵 Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀 Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵 Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀 Single Disc Flat Gate Valves 单闸板平板闸阀 Single Opening Exhaust Valves 单口排气球 Slurry Pumps 泥浆泵Stop Valves 截止阀 Strainer 过滤器 Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀 Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀 T-Cock 三通Thin Gate Valves 薄型闸阀 Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀 Triple (tee) valves 三通阀Two-way valves 二通阀 Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵) Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀 Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀 Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀 Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套 Ball 球、球芯Ball seat 密封圈 Blowdown Sealing Face 启、阀件密封面Body 阀体 Bonnet 阀盖Disc 阀瓣 Mut 螺母Screw 螺栓 Sealing 密封件Spring 弹簧 Stem 阀杆Stem Mut 阀杆螺母 Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质 Applicable temperature 适用温度Butt Clamp 对夹 Chemical analysis 化学成份Connecting format 连接形式 Double disc 双闸板Flexible disc 弹性闸板 Flange 法兰 Hoop 卡箍Inside thread 内螺纹 Jacket 夹套Mains 电源 Material chemical analysis and mechanical capacity材料化学成份和机械性能 materials 材料 Materials for main parts 主要零件材料 Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量 Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度 Max. Allowable Pressure 最高允许压力Model 型号 N ame of parts 零件名称nitrogen (N) 氮 Nominal bore 公称通径Nominal Pressure 公称压力 Nozzle 排气口Outside thread 外螺纹 Oxidant 氧化性介质Parallel 平行 Piping 管路Piston 活塞 Reductant 还原性介质Rising stem 明杆 Seal 阀座,密封面Seat testing pressure 压力气密封试验压力 Socket 卡套Specifications 性能规范 Single disc 单闸板Solid 刚性 Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水 Stroke 冲程,行程Water,oil,steam 水,温度,气 Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢 Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜 Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属 Chromel alloy 镍铬合金CHR rubber 氯晴橡胶 Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢 Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫 Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁 Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢 Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁 Haynes alloy 钴铬钨合金High tem perature steel 高温钢 Monel 蒙乃尔合金Low temperature steel 低温钢 Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯 Polythene 聚乙烯Pure aluminium 纯铝 Pure cupper 纯铜Rubber graphite board 橡胶石墨板 Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢 Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢 Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力 Service Fluid 工作介质。
海瑞克盾构设备-英汉对照英文汉语proportional valve block 流量阀brake valve 闸阀double prestress valve 流量阀proportional valve block 流量阀valve 闸阀valve 闸阀ball valve 球阀ball valve w/lever/ 球阀shuttle valve 闸阀ball valve 球阀check valve sae11/2 闸阀valve 闸阀ball valve 球阀nozzle 喷嘴proportional valve 流量阀pressure reducing valve 减压阀plate 连接块plate 连接块erector 管片安装机cutting wheel drive 刀盘主驱动tank 水箱cylinder 液压油缸waggon 运输料槽jack 千斤顶thrust jacks unit+stroke meas 主推进油缸planetary gear 齿轮箱gear oil cooler 齿轮油冷却器thermometer 0-80 degrees c 温度计ball valve 球阀valve 闸阀control block 接线板plate 连接块mechanical directional control 方向控制器pressure control valve 流量阀control block 接线板slide block 滑动轴承阻挡块hydraulik block 液压阀组pressure reducing valve 减压阀non return valve 止回阀one-way restrictor zp 闸门directional control valve 流量阀pressure reducing valve zp 流量阀ball valve dn13 球阀block ball valve 球阀nonreturn valve 止回阀ball valve dn13 球阀pressure transducer 压力传感器hydraulic block 液压阀组ball valve dn13 球阀control block 接线板current dividing coil 线圈pressure fuse 保险融管pressure switch with indicatio 压力计shaft 连接轴flowmeter 流量计interlock means 管接头compressed air pump 压缩空气泵washer 垫片cylinder head screw 螺丝screw / m24x360 螺丝washer 垫片nut m24 螺母filter 过滤器round cord 密封圈screw / m16x40 螺丝ventilation filter 过滤器measuring device 测量装置binding 扎带dive motor pump 排液泵sheet metal package 盾体连接块erector parts 安装机连接梁rail 导轨gate valve 闸阀pressure gauge , type 213.53 压力表hexagon nut 螺帽lamp 灯泡pump 冷却泵thrust jacks unit+stroke meas 推进油缸compensator 补偿器seal 密封件placa de goma 密封件plug 销子load support 支架screw fitting 管接头screw pump 螺旋泵high pressure filter 过滤器level control 水平控制仪steel tank 水箱sound absorber 吸音器pressure gauge , type 213.53 压力计replenish-ventilation filter 通风过滤器grease lubrication pump unit 油脂集中润滑泵grease pump 200l 油脂泵pressure switch 压力计coupling 管接头pipe 钢管sleeve coupling 套筒t-piece t型块o-ring o型圈regulation system 气体调节系统flange 法兰welding neck 焊接用连杆flange 法兰lifting device 起吊葫芦pressure transducer 压力传感器shaft support 支架control 电力控制器gasket 密封圈switch 压力传感器cranking 7,5 kw 压力传感器spherical plain bearing 滚珠轴承installation 安装flange 法兰pipe bend 管接头welding neck 焊接用连杆welding neck 焊接用连杆hose 液压管cover 盖板ring 环片fixture 支座fixture 支座slide bearing 滑动轴承bearings 滚珠轴承mesh platform 防滑平台gasket 密封圈distributor 分配器gate valve 闸阀clamp 锁紧接头thimble 套管chain 链条load cell 支座housing 支座amplifier 沙浆座module 支座high pressure cleaner 高压水喷头back flow prevention 止回阀clamp 锁紧接头plain slide valve flange pn16 法兰motor 液压马达hydraulic aggregate 液压阀组hydraulic hand pump 液压手泵directional control valve 方向阀one-way restrictor zp 闸门return valve 回流阀block ball valve 球阀hydraulic fitting female 液压接头hydraulic fitting male 液压接头pressure transducer 压力传感器ball valve with pneumatic driv 球阀wire brush seal 盾尾密封刷rail 支座heat exchanger 热交换器bend 90degree 弯头angle 角接头short bend 90 degree 弯头t-piece t型块nipple 喷嘴counter bearing 沙浆箱轴承drive bearing 沙浆箱驱动轴承angle 角接头ellbow 90°弯头bracket 连接件main distribution 2 电力分配柜equipment 电力分配柜drum 电缆卷筒hose 软管thrust jacks unit+stroke meas 液压阀组screw compressor 螺杆式空气压缩机water unit 水冷却单元level control with water flush 水平控制仪back flow prevention 止回阀pressure gauge 压力计capasitive ropeprobe 14 m 连接软管sensor 感应器fixture 支座grating 隔栅planetary gear 推进齿轮pressure transducer 压力传感器reducing fitting 管接头clamping jaw 锁紧接头conduct 导管electric cable 电缆conduct 套管cable 电缆planetary gear 推进齿轮level control 水平控制仪sound absorber 吸音器brake 闸门safeset 安全套件bolt dynamometer 螺旋测力计threaded rod 螺纹连杆safety-bumper 缓冲器incadescent lamp 白炽灯cable channel 电缆槽steel tube 圆钢clamping jaw 锁紧接头equipment 电力分配柜washer hv 垫片camera 摄像头welding neck 焊接用连杆mesh platform 防滑平台template 模板plug 销子cover 盖板switch 开关cranking 7,5 kw 发动机chain 链条thimble 套管clamp 锁紧接头gasket 密封圈screw fitting 管接头press fittings 管接头placa de goma 连接片sound absorber 吸音器thermometer 温度计clock 钟non return valve 止回阀axial full bevel nozzle 喷嘴heating installation 加热器heating installation 加热器band recorder dual 计录器lock 锁agitator 鼓风机/搅拌机feed pump 泵pump 泵directional solenoid valve dn5 方向阀pressure reducer 减压器flowmeter 流量计aggregate 液体泵站fixing device 固定件erector head 管片安装机机头attachment 连接器transformer 压力传感器wire brush seal 盾尾密封刷ventilator 通风机rope measuring probe housing 支座spring 弹簧spherical disk 连接球cap 螺帽compound slide 连接滑块screw fitting 管接头connector 继电器hydraulic feeder 进料器gate valve 门阀terminal block 终端阀组shackle 挂钩clamp 锁紧接头high pressure cleaner 高压水枪头bolt dynamometer 螺旋测力计belt 输送带wire brush seal 盾尾密封刷revolving joint 主旋转接头console 控制台frequency converter 变频器main distribution 1 电力分配柜high consistency pump 排液泵control block 液压阀组high consistency pump 排液泵hydraulic feeder 喂料器t-block t型块ventilator 通风机current dividing coil 线圈measuring device 测量仪buffer 垫片grease carton - slurry pump 泥浆泵waggon 输送料槽jack 千斤顶changing magazine 储管器control cabin 电力控制柜suction filter 过滤器stop gate dn80 闸门level check 水平测量仪console 控制台reduction 减压器diffuser 扩散器rope clamp system 缆绳锁紧单元diffuser 蓄能器changing magazine 储管器electric motor 电动马达damping rail 缓冲槽variable displacement pump 排液泵o-ring o型圈proximity switch 接近开关lubricating nipple 喷嘴roller 滚筒frequency converter 变频器connector 继电器terminal block 终端阀组bulkhaed gate 盾体闸门fluorescent lamp 荧光灯slide bearing 滑动轴承band 带子hemp 带子fermit can 油漆paint brush 油刷fork-shaped piece 连接块belt 输送带telephone 紧急电话welding neck 焊接用连杆bush 衬套sticker 标签housing 刀箱t-piece t型块cable socket 电缆插座slide bearing 滑动轴承screw tension cylinder m64 m64螺栓拉伸油缸high pressure power pack 高压动力包high pressure hose 1600bar高压油缸high power aggregate g20 g20高压泵站insert for screw driver sw 65 sw65套筒insert for screw driver sw 55 sw55套筒power screw driver hydraulic 液压动力扳手high pressure hose 高压油管displacement cylinder 移位液压油缸aggregat 液压泵站container 20" 20"集装箱shield 盾体installation thrust jacks 推进千斤顶thrust jacks unit+stroke meas 推进系统+thrust cylinder 推进油缸cuttingwheel drive 刀盘驱动seal 密封planetgear 行星齿轮箱motor water cooled 马达水冷却pinion 小齿轮seal 密封erector 拼装机planetarygear 行星齿轮箱displacement motor 变速马达hudraulic scheme/grout injection 液压回路/注浆回路high consistency pump 高压泵water circuits s-317 水循环s-317slurry circuit 泥浆回路pump 泵ball valve+hydraulic drive 球阀+液压驱动electric motor 电动马达particulate pump 小型泵pump 泵motor 马达flange ball valve 法兰球阀vacuum scheme 真空装置vacuumpump 真空泵cutterheadmotor 刀盘马达hydr.agitator 液压搅拌机hydr.thrust ram 液压推力缸hydr.erector 液压拼装机circulation pump p-0.1 循环泵hydr.grouting 液压注浆pump pipe pig 清洗泵hydr.auxiliary 1 液压辅助设备1pump internal coolingcircuit 内冷却循环泵pump dewatering coolingwater 抽水泵pump water highpressure 高压水泵segment transport crane 管片起重机segment transfer crane 管片搬运机road-element crane 道路机exit reserve 逃出储备sockets 插座hydr.overcutter 液压超挖刀pump industrialwater 工业用水泵pump gearoil 1 齿轮油泵1hydr.auxiliary 2 液压辅助设备2 hydr.filtercircuit 液压滤波电路lubrication pump 润滑油泵grout tank 1 agitator 浆桶1 搅拌机english german chinese accumulator 蓄能器adjacent switch 接近开关agitator 搅拌机air bubble 气泡air-buffer 气体缓冲器air cleaner 空气滤清器air-compressor 空气压缩机air-conditioner 空调air filter 空气过滤器air-lock 气闸air outlet 放气,排气air pump 气泵air tank 空气箱air valve 气阀air vent 气孔align cylinder 校正油缸allowed variation 容许偏差alternator 交流发电机angle 角度antenna 天线anti-rotation device 反转装置,防止旋转装置anti-wear plate 耐磨板arm 臂arm retainer 臂固定架articulation cylinder 关节油缸articulation jack 铰接千斤顶articulation jack pin 铰接千斤顶连接销articulation jack pin mounting jig 铰接油缸连接销安装夹具articulation lip seal 关节法兰盘密封articulation rubber sponge seal 关节海绵橡胶密封assembly 装配,组装auto grease lubricator 自动滑脂润滑器auto oil lubricator 自动注油器automatic control 自动控制automatic drain 自动放泄阀valve 自动排水阀automatic feed water pump 自动供水泵automatic oil lubrication 自动润滑auxiliary cutter bit 辅助切削刀auxiliary transformer 辅助变压器back filling injection device 壁后注浆装置back filling injection port 壁后注浆孔backlash 间隙,齿隙back up 后配套装置balancing value 平衡阀ball joint 球窝接头ball tap 球形旋塞ball valve 球阀band 嵌条base plate 底座beam 梁bearing 轴承bearing house 轴承座bearing house stopper 轴承座挡块bearing lubrication unit 轴承润滑装置bearing pad 轴承垫belt 皮带belt conveyor 皮带输送机belt tensioning cylinder 皮带张紧油缸bend 弯管,弯头binder 粘合剂blade 叶片,刀片blind plug 废堵,盲塞block (阀)板,(阀)块bogie 转向架,车轮bolt 螺栓boom 起重臂bore diameter 孔径boring machine 钻机boss 轮毂bracket 托架,支柱brake 制动器breakdown 故障breaker 断路器,开关(电)breather 通气孔;通风装置broken line 虚线,点线brush 刷子,毛刷brush seal 刷子密封bucket 铲斗,挖斗built-in stroke sensor 内置式行程传感器bulkhead 舱壁,隔板bush 衬套,轴瓦butterfly valve 碟型阀butt joint 对接button 按钮cable 电缆滑线cable bearer 电缆滑线支架cable duct 电缆滑线导管cable rack 电缆滑线架cable reel 卷盘cable tray 桥架cable way 通道cable with connector 带接头的cam follower 凸轮从动件can 罐头cap 盖,帽cardan joint 万向接头carriage 车架cat walk 走道,过道,通道cat walk bracket 走道支架center cutter 中心转刀center line 中心线center shaft 中轴center slide deck 中间的移动平台centralized grease system 集中润滑系统centrifugal pump 离心泵chain 链条chain block 导链滑车chain link 链节chamber 室charge 装料;充电charger 装料设备,装(送)料机charging hopper 装料料斗chart 图,图表check valve 单向阀chemical grouting 化学灰浆chute 斜槽;滑槽circuit 电路circuit breaker 断路开关clamp 钳,夹紧clay 粘土cleaner 滤清器cleaning pump 洗涤泵cleaning water injection port 清洗水注入孔clearance (机器零件之间的)间隙clevis 弹簧钩,u形夹clogging 堵塞clutch 离合器collapse detector 土体塌陷探测器collar 轴衬colour display 彩显column 立柱component 部件compressed air 压缩空气compressor 空气压缩机computer 计算机connecting beam 联结双梁connecting pin fixing plate 联结销固定板connecting shaft 联结轴connecting stay 联结支柱connection tool 联结工具connector 接头consent 插座contactor 接触器,开关contra fan 逆流式通风机control 控制control box 控制箱control cabin 控制室control panel 控制面板control room 控制室controlled inlet valve 可控进给阀controlled outlet valve 可控压力阀controller 控制装置cooling water pump 冷却水泵copy cutter 仿形刀copy cutter bit 仿形刀刀片copy cutter jack 仿形刀千斤顶coupler 联结器coupling 联结器coupling for cutter detector 刀盘探测器的联结器cover 盖子cover plate 盖板current 电源current failure 断电,停电curve 曲线cushion rubber 缓冲橡胶cutting edge 切消刃cutter bit 刀盘切割刀,硬质合金刀cutter bit hold 切削刀刀架,硬质合金刀刀架cutter chamber 刀盘隔仓cutter driving motor 刀盘驱动马达cutter drive power 刀盘驱动电源cutter driving unit 刀盘驱动装置cutter drum 刀具盘体cutter head 刀盘刀头cutter head gear motor 刀盘减速箱cutter ring 刀圈cutter seal 刀盘密封cutter spoke 刀盘轮辐cutter tooth 刀齿cutter torque 刀盘扭矩cutter motor 刀盘驱动马达cycle 周期,循环cylinder 油缸cylinder guide ring 油缸导向环data 数据deck 平台;面板deck handrail 平台扶手deck stand 平台架子deck stand support 平台支柱dedusting system 除尘系统delay time 延期detail 细节detector 探测器dewatering 排水dewatering pump 排水泵diagram 图表diameter 直径digger 挖掘机disc cutter 盘形滚刀discharge valve 放泄阀,排气阀discharge hopper 卸料斗displacement 位移displacement detector 位移传感器distribution 分配distribution valve 分配阀distributor 配电器drain 排出口drainage water lifting pump 排水提升泵drawing 图纸drill equipment 钻头装置drill machine 钻机drive 驱动drive system 驱动系统driving motor 驱动马达driving motor cooling system 驱动马达冷却系统drum 滚筒double arm 双臂(式)double blade 双刀片double gate 双闸门double nut 双螺母dust wiper 除尘器earth collapse detector 土体勘查装置earth and sand destruction 土砂破坏检测装置detection deviceearth and sand seal 土砂密封earth load gauge 土压测量计earth pressure balance shield 土压平衡盾构earth pressure detector 土压勘查装置elastic ring 弹性圈elbow joint 弯管接头electric motor 电动马达electric valve 电磁阀eletronic component 电气元件elongation capacity 延性end plate 端板emergency dewatering hose 紧急排水软管emergency dewatering pump 紧急排水泵emergency light 应急灯emergency break 紧急制动器emergency stop 紧急停机encoder 编码器engineering plastic knob 工程塑料捏手equalizer 平衡器equipment 设备erector 拼装机erector grip assembly 拼装机夹紧装置erector torque 拼装机扭矩excavation 开挖excavation diameter 开挖直径excavation face 开挖面excavation speed 开挖速度expansion tank 油枕extend-retract 伸缩extension 伸extension jack 伸缩油缸extension port 延伸出口eye plate 眼板eye bolt 带圈螺栓fan 风扇,风机fault 故障feed 供给;送料feed valve 进给阀feeder hopper 加料器feeder hopper 进料斗filter 过滤器fishtail cutter 鱼尾形切削刀fixing bolt 紧固螺栓fixing plate 固定板flange 法兰flapper 铰链板flapper 有铰链大门float switch 浮动开关floor drain 地面排水flow 流量flow control valve 流量控制阀flow conveyor 流动输送机(输送水泥用)flow-meter 流量计flow ing carriage 后续车架flow rate 流量flow pipe 输送管flow sheet 流程图fluorescent light 荧光灯foam 泡沫force 力frame 支架front trunk 前壳体full bore ball valve 球阀(四面都带接头)fuse 保险丝grantry 台架gap 空隙gasket 垫片gate 闸门gate plate 闸门板gear 齿轮gear box 齿轮箱,减速器gear box with brake 带制动器的减速箱gear pump 齿轮泵generator 发电机gland 封头;密封套globe valve 球(形)阀gouging 表面切割governor 调节器,调速器grease 油脂grease gun 润滑脂枪,牛油枪grease lubrication 滑脂润滑grease pump 油脂泵grease seal 润滑脂密封grip 夹具,把手grip bolt 夹紧螺栓grip cylinder 夹紧油缸gripper 夹具装置gripper shoe 夹具撑靴ground 地面guide pipe 导管guide rod 导杆guide roller 导向滚筒gyro 陀螺仪half coupling 半联结器hammer 锤handle 摇柄handrail 栏杆,扶手hanger 吊钩hand-operating device 手动操作hexagon head bolt 六角头螺栓hexagon nut 六角螺母hexagon socket screw 内六角螺栓high density slurry 高密度泥浆high density slurry shield 高密度泥水盾构high-pressure vcb panel 高压vcb配电板hinge 铰链hob 齿轮滚刀hoist 葫芦hoist beam 起吊运输梁hoist rail 起吊运输轨道holder 刀架hole 孔hollow shaft 空心轴hook 弯钩;吊钩hood 盖,套;防护罩hopper 料斗horizontal thrust 水平方向hose 软管hose clamp 软管夹hose rack 软管托架h.v cable reel 高压卷筒h.v cell 高压电池hydraulic 液压hydraulic control unit 液压控制系统hydraulic drive 液压驱动hydraulic oil tank 油箱hydraulic motor 液压马达indicator 指示灯injection 加注injection hole 注入孔injection pipe 注浆管injection pump 注浆泵injection valve 喷射阀;注浆阀inlet valve 进给阀inner diameter 内径inner tube 内壳体inside diameter 内径inspection 检查inspection cover 观测盖板,检查盖inspection hole 检查孔inspection lamp 检修(用)灯inspection window 观察窗installation 安装installation board 安装板interlock 联锁interlock pin 联锁销intermediate beam 中间梁intermediate bearing 中间轴承intermediate coupling device 中间联结(藕合)装置intermediate shaft 中间轴inverter 变换器,倒相器jack 油缸,千斤顶jet valve 喷射阀jib 旋臂jib crane 旋臂起吊装置jig 夹具joint 接头junction valve 连接阀key 键key plate 止转板kit 工具箱knock pin 定位销ladder 梯子lap 搭接;重叠laser 激光laser beam 激光束laser sensor 激光传感器leader pin 导销leak 泄漏left 左level 水平,水位level gauge 液位计lever sensor 水平传感器lifetime 使用寿命lift 升降机;电梯lift cylinder 提升油缸lift jack 提升油缸lifting beam 提升梁lifting piece 吊攀lifting rod 提升杆light 光,灯光lighting 照明lime 石灰limit 限制limiter 限制器limit switch 限位开关line filter 线路滤波器liner 衬套,衬垫lining 衬板,衬垫link chain 扁节链,平环链lip seal 唇形密封load 载荷lubrication 润滑lubricating unit 润滑装置machine plane 机加工面main bearing 主轴承maker 生产厂家,制造厂商manhole lid 人行孔盖manifold 阀板man lock 人行闸manipulator 操纵装置,机械手material 材料measure 测量;量度measure stroke sensor 测量行程传感器middle beam 中间梁mode 模式molten metal 熔融金属proportional valve block 流量阀brake valve 闸阀double prestress valve 流量阀proportional valve block 流量阀valve 闸阀valve 闸阀ball valve 球阀ball valve w/lever/ 球阀shuttle valve 闸阀ball valve 球阀check valve sae11/2 闸阀valve 闸阀ball valve 球阀nozzle 喷嘴proportional valve 流量阀pressure reducing valve 减压阀plate 连接块plate 连接块erector 管片安装机cutting wheel drive 刀盘主驱动tank 水箱cylinder 液压油缸waggon 运输料槽jack 千斤顶thrust jacks unit+stroke meas 主推进油缸planetary gear 齿轮箱gear oil cooler 齿轮油冷却器thermometer 0-80 degrees c 温度计ball valve 球阀valve 闸阀control block 接线板plate 连接块mechanical directional control 方向控制器pressure control valve 流量阀control block 接线板slide block 滑动轴承阻挡块hydraulik block 液压阀组pressure reducing valve 减压阀non return valve 止回阀one-way restrictor zp 闸门directional control valve 流量阀pressure reducing valve zp 流量阀ball valve dn13 球阀block ball valve 球阀nonreturn valve 止回阀ball valve dn13 球阀pressure transducer 压力传感器hydraulic block 液压阀组ball valve dn13 球阀control block 接线板current dividing coil 线圈pressure fuse 保险融管pressure switch with indicatio 压力计shaft 连接轴flowmeter 流量计interlock means 管接头compressed air pump 压缩空气泵washer 垫片cylinder head screw 螺丝screw / m24x360 螺丝washer 垫片nut m24 螺母filter 过滤器round cord 密封圈screw / m16x40 螺丝ventilation filter 过滤器measuring device 测量装置binding 扎带dive motor pump 排液泵sheet metal package 盾体连接块海瑞克盾构机中英文对照表erector parts 安装机连接梁rail 导轨gate valve 闸阀pressure gauge , type 213.53 压力表hexagon nut 螺帽lamp 灯泡pump 冷却泵thrust jacks unit+stroke meas 推进油缸compensator 补偿器seal 密封件placa de goma 密封件plug 销子load support 支架screw fitting 管接头screw pump 螺旋泵high pressure filter 过滤器level control 水平控制仪steel tank 水箱sound absorber 吸音器pressure gauge , type 213.53 压力计replenish-ventilation filter 通风过滤器grease lubrication pump unit 油脂集中润滑泵grease pump 200l 油脂泵pressure switch 压力计coupling 管接头pipe 钢管sleeve coupling 套筒t-piece t型块21 / 21。
阀门名词术语中英文对照阀门valve闸阀 gate valve截止阀globe valve, stop valve节流阀throttle valve球阀ball valve蝶阀butterfly valve隔膜阀 diaphragm valve旋塞阀plug valve止回阀check valve, non-return valve安全阀safety valve, pressure减压阀pressure reducing valve疏水阀steam trap排污阀 blow-down valve调节阀(控制阀)control valve, adjusting valve 分配阀 dividing valve混合阀 mixing valve水力控制阀 hydraulic control valve手动阀门 manual operated valve电动阀门 electrical operated valve气动阀门 pneumatically operated valve 低压阀门 low pressure valve中压阀门 middle pressure valve高压阀门 high pressure valve超高压阀门 super high pressure valve 高温阀门 high temperature valve中温阀门 moderate temperature valve 常温阀门 normal temperature valve低温阀门 sub-zero valve超低温阀门 cryogenic valve结构长度 face-to-face dimension结构形式 type of construction直通式 through way type角式 angle type直流式 y-type三通式 three way typeT形三通式 T-pattern three wayL形三通式 L-pattern three way平衡式 balance type杠杆式 lever type常开式 normally open type 常闭式normally closed type保温式 steam jacket type波纹管式 bellows seal type全径阀门 full-port valve缩径阀门 reduced-port valve缩口阀门 reduced-bore valve单向阀门 unidirectional valve双向阀门 bidirectional valve上密封back seal压力密封pressure seal连接形式 type of connection壳体 shell阀体body阀盖bonnet启闭件disc阀座seat密封面 sealing face,surface阀杆 stem, spindle阀杆螺母yoke nut填料函(填料箱)stuffing box填料packing, packing rings填料垫packing seat, packing washer支架 yoke撞击手轮impact hand wheel阀瓣(阀芯) disc(valve core)楔式闸阀wedge gate valve闸板wedge单闸板single gate刚性闸版 rigid gate弹性闸板 flexible gate disc双闸板double gate楔式双闸板 wedge double gate平行式双闸板 parallel double gate浮动式球阀floating ball valve固定式球阀fixed ball valve球体 ball斜板式蝶阀inclined disc butterfly valve 蝶板 disc屋脊式隔膜阀weir diaphragm valve截止式隔膜阀 globe diaphragm valve隔膜diaphragm填料式旋塞阀 gland packing plug valve 油封式旋塞阀 lubricated plug valve塞子 plug升降式止回阀 lift check valve升降立式止回阀 vertical lift check valve 旋启式止回阀 swing check valve底阀 foot valve,bottom valve轴流式止回阀 axial flow check valve蝶式止回阀 butterfly swing check valve 销轴 hinge pin摇杆 arm先导式安全阀 pilot operated safety valve 全启式安全阀 full lift safety valve微启式安全阀 low lift safety valve双联弹簧式安全阀duplex safety valve真空安全阀vacuum relief valve敞开式安全阀openly sealed safety valve调节螺母adjusting screw弹簧座 spring plate导向套 dise guide反冲盘 disc holder调节圈 adjusting ring压力释放装置pressure relief device爆破片装置bursting disk device折断销装置breaking pin device弯折销装置buckling pin device剪切销装置shear pin device易熔塞装置fusible plug device排放面积discharge area流道面积flow area流道直径flow diameter帘面积curtain area开启高度lift额定开高rated lift密封面斜角seat angle密封面积seat area密封面平均直径seat mean diameter净流通面积net flow area喉径 throat diameter整定压力set pressure超过压力overpressure回座压力reseating pressure启闭压差blowdown排放压力 relieving pressure排放背压力 built-up back pressure附加背压力 superimposed back pressure理论排量 theoretical discharge capacity 额定排量 certified (discharge) capacity 频跳 chatter颤振 flutter封闭式 seal type非封闭式 unseal type在用试验in-service testing工作台上定压试验bench testing薄膜式减压阀 diaphragm reducing valve活塞式减压阀 piston reducing valve杠杆式减压阀 lever reducing valve膜片 diaphragm浮球式疏水阀 ball float steam trap浮桶式疏水阀 open bucket steam trap脉冲式疏水阀 impulse steam trap热动力式疏水阀 thermodynamic steam trap 蒸汽疏水阀 steam trap工作压力 operating pressure最高工作压力 maximum operating pressure 最低工作压力 minimum operating pressure 工作背压 operating back pressure背压率 rate of back pressure最大压差 maximum differential pressure最小压差 minimum differential pressure开阀温度 operating valve temperature关阀温度 closing valve temperature过冷度 subcooled temperature最小过冷度 minimum subcooled temperature 冷凝结水排量 cold condensate capacity热凝结水排量 hot condensate capacity漏汽量 steam loss无负荷漏汽量 unload steam loss 有负荷漏汽量 load steam loss无负荷漏汽率 rate of unload steam loss有负荷漏汽率 rate of load steam loss负荷率 rate of load condensate阀片 disc钟形罩 inverted bucket浮球 float ball浮桶 float bucket执行机构 actuator基本误差 intrinsic error回差 hysteresis error死区 dead band行程 travel额定行程 rated travel相对行程(h) relative travel(h)额定行程偏差 deviation of rated travel额定流量(Q) rated flow(Q)泄漏量 leakage流量系数 flow coefficient额定流量系数(K V)rated flow coefficient(K V)相对流量系数(Φ)relative flow coefficient(Φ)固有流量特性 inherent flow characteristic 可调比(R) inherent rangea bility(R)阻塞流 choked flow斜率偏差 slope deviation遥控浮球阀remote float control valve水利控制减压阀 pressure reducing valve缓闭止回阀 low speed closed check valve 持压/泄压阀 pressure sustaining ,relief valve 水泵控制阀 pump control valve最小开启压力 minimum open pressure驱动装置 actuator多回转驱动装置multi-turn actuator部分回转驱动装置part-turn actuator电动装置electric actuator气动装置pneumatic actuator直线型气动装置 linear pneumatic actuator回转型气动装置rotary pneumatic actuator气动装置的行程stroke of pneumatic actuator 液压驱动装置 hydraulic actuator电磁驱动装置 electro magnetic actuator 电-液联动装置electro hydraulic actuator气-液驱动装置pneumatic-hydraulic actuator 蜗轮传动装置 worm gear actuator正齿轮传动装置cylindrical gear actuator锥齿轮传动装置conical gear actuator转矩torque推力thrust壳体试验 shell test壳体试验压力 shll test pressure密封试验 seal test密封试验压力 seal test pressure上密封试验 back seal test静压寿命试验potential pressure life test耐火试验 fire test防静电试验 anti-static test主要性能参数specification公称压力nominal pressure公称尺寸nominal diameter工作压力 working pressure最高工作压力 maximum operating pressure工作温度 working temperature最高工作温度 maximum operating temperature 泄漏量 leakage吻合度 percent of contact area连接尺寸 connection dimension最大压差 maximum pressure differential 位置指示器 position indicator压力边界 pressure boundary。
刀形浆闸阀Knife Gate Valve产品概述General Product Description1、刀形浆闸阀按照口径不同制成暗杆和明杆两种型式(DN50-DN400 为暗杆DN450-700为明杆),全圆形的直流通道设计不存渣、不卡阻。
阀板底端加工成刀刃状,对松软物料如纤维、纸浆、木浆具有切断功能,同时有良好开启和关闭作用。
在阀板上端安装有硬聚四氟乙烯刮泥器,可防止粉尘、砂砾等擦伤性物质进入填料盒,可显著提高阀板寿命。
阀板材质选用不锈钢,精磨抛光处理可获得最佳密封效果。
The knife gate valve is manufactured as two types: non-rising stem and rising stem according to the diameter difference (DN50-DN400 non-rising stem and DN450-700 rising stem). The design of round flow-through channel as a whole allows no sediment or clogging. The wedge bottom is made into a blade shape with the purpose to cut some soft materials such as fiber, pulp or wood pulp, and it also serves favorable closing and opening. There is a hard PTFE mud scraper at the top of wedge to prevent scuffing substance such as dust or gravel coming into the packing box and it will improve the wedge service life remarkably. The wedge is made of stainless steel, ground and polished nicely for the best sealing effects.2、阀体、填料函均为精密铸造,其中阀体采用凸缘式整体铸造,材质可根据用户需要选用304、316、316L、WCB、2Cr13,密封圈采用RTFE增强聚四氟乙烯材质,耐腐蚀、耐磨损、不沾渣。
The valve body and packing box are under precise casting, of which the body is integrally cast as a rimmed type. Material may be selected by the client as 304, 316, 316L, WCB or 2Cr13 and sealing ring may be RTFE, much desirable in corrosion resistance, wear resistance and free from slagging.3、阀板有5个支撑点,使阀板有很好的自对中。
当阀门处于关闭状态,并承受背压时,阀板不发生偏移。
There are 5 support points on the wedge to allow good centering for the wedge. When the valve is closed and endures back pressure, the wedge will not deviate any more.4、刀形浆闸阀可以配置手轮、快开手柄、手动拉链、齿轮传动、手动和电动。
The knife gate valve may be equipped with hand wheel, quick-opening handle, manual chain, gear transmission, manual and electric mode.5、刀形浆闸阀内部可制成V型、三角型、五角型通道,以适应流体调节控制要求。
The inner structure of the knife gate valve may be designed as V-type channel, △-type or pentagon type channel to accommodate fluid control.6、刀形浆闸阀连接形式有对夹式、法兰支耳式,密封有金属硬密封、增强的聚四氟乙烯密封。
The connection mode for knife gate valve includes wafer and flange lug, and sealing includes metal hard sealing, RTFE sealing.7、工作温度Operation TemperatureV型通道V-type Channel△型通道△-type Channel液体Fluid干料Dry Material介质浓度Medium Concentration洛氏硬度Rockwell Hardness公称压力Nominal Pressure压力试验标准Pressure Test Standard法兰连接标准Flange Connection Standard欧洲体系(化工部)标准European System Standard (Ministry of Chemical Industry)国家标准National Standard四氟密封PTFE Sealing硬密封Hard Sealing适用介质Applicable Medium金矿粉、尾矿、纸浆、木浆、纤维、粉尘、化学品处理污水、沉淀池、矿砂、炉渣、煤泥、沥青、料仓出口、水果、谷物、水泥浆、屠宰厂废水、气动输送管线或啤酒酿制的介质。
Media as gold powder, tailings, pulp, wood pulp, fiber, dust, chemical sewage and medium in sedimentation tank, or as ore, cinder, coal slime, asphalt, and medium from bin outlet, fruit, grain, cement paste, sewage from slaughter house, or medium in pneumatic pipes or beer brewing.适用行业Applicable Industries造纸工业及化学工业、冶金矿山、电力行业、石化、煤炭、纺织工业、水泥行业、制糖工业、蔬菜加工、食品加工、污水处理。
Paper Industry and Chemical Industry, Metallurgical and Mining Industry, Power Industry, Petrochemical Industry, Coal, Textile, Cement, Sugar, Vegetable, Food Processing and Sewage Treatment Industry.产品特点Product Features设计紧凑、占据空间小、重量轻、价格便宜、易于安装、耐磨防堵措施完善、便于维修、使用方便及寿命长,广泛应用工业条件苛刻的环境中。
It is of compact design with less space, light weight, lower price and easy installation. It is of completed wear resistance and anti-clogging, easy in repair and operation with longer service life, so it is widely applied in some sever industrial conditions.刀形浆闸阀Knife Gate Valve零件名Name of Parts材料Material手轮Hand Wheel丝杠Lead Screw不锈钢Stainless Steel阀板Wedge密封圈Sealing Ring聚四氟乙烯PTFE阀体Valve Body公称通径Nominal Diameter主要外形尺寸Main Overall Dimension额定流量系数Rated Flow Coefficient全开Full Open重量Weight手动阀门Manual Valve注明:MPa1.6阀门选型按上表、法兰连接尺寸按国家标准。
Remarks: Selection of Valve MPa1.6 is made according to the Table above and the flange connection size is based on the national standard.填料压盖Packing Gland铸钢、铸铁Cast Steel and Cast Iron注明:根据用户要求可生产全密封带防尘罩浆闸阀,主要应用在矿山、水泥、化工、食品等行业。
Remarks:Fully-sealed knife gate valves with dust cover may be produced as the client requires. They are mainly applied in such industries as mining, cement, chemical and food production.注:1.6MPa阀门选型按上表,连接尺寸按国家标准。
Remarks: Selection of Valve MPa1.6 is made according to the Table above and the connection size is based on the national standard.参考Reference电动浆闸阀Electric Knife Gate Valve电动装置型号Electric Device Model气动浆闸阀Pneumatic Knife Gate Valve气动装置型号Pneumatic Device Model蝶阀Butterfly Valve用途Application本阀适用空气、煤气、可燃气体、酸、碱、油品、纸浆水等水介质的管路上,作调节和截流作用。