华光挂烫机说明书
- 格式:pdf
- 大小:1.43 MB
- 文档页数:5
fl870说明书
一、注水
蒸汽挂烫机是通过灼热水蒸汽不断接触衣物,软化衣物的纤维组织的
机器。
所以第一件事情就是,要记得加水。
加水要注意两点:1、加水时
最好加纯净水,锅胆发热纯净水杂质少不容易结成水垢,可以延长锅胆使
用寿命,纯净水出来的蒸汽也不会损害衣物。
2、不要向水箱里注入热水,不然会影响发热锅使用寿命。
二、固定
将衣服固定在衣架上,裤子的话最好可以平放,或者是裤架棒固定。
单杆挂烫机通常不是很稳定,最好选用双杆的挂烫机。
华光的双杆就
非常稳定,独特的架构设计可以轻松的熨裤子,熨裤线。
三、熨烫
挂烫机是挂烫的,烫衣服时,轻轻拉住衣服的下摆,尽量把褶皱的地
方拉平,烫衣领时,把衣领翻过去烫,会比较好烫。
最好要有烫衣小助手,带上防烫手套。
四、分档
熨烫的时候要注意了,不同的织物应该有不同的挡位。
厚实的用大功
率的挡位,轻薄的用小功率的挡位。
购买时最好购买多挡的。
这样熨烫更
顺心。
五、保养
1、衣服熨烫后不宜直接放到衣橱里,剩余的蒸汽会使衣物发霉,需要在外晾一段时间。
2、衣服熨完后就穿很容易使衣服变皱,除非是用华光强力蒸汽系列的。
3、熨过的衣服不宜放的太挤,否则容易起皱。
蒸汽挂烫机使用方法1.准备工作在使用蒸汽挂烫机之前,我们需要做一些准备工作。
首先,将蒸汽挂烫机放置在平稳的水平面上,确保它稳定而不易倾倒。
然后,检查水箱是否装满清水,如果没有,就需要加满水。
接下来,将插头插入合适的电源插座,并确保连接牢固。
2.加热和预热一般来说,蒸汽挂烫机的加热和预热时间需要几分钟。
在加热过程中,水会被加热成蒸汽。
待挂烫机准备好后,一般会有指示灯亮起提示。
确保挂烫机已经预热完毕后,即可开始使用。
3.挂烫衣物在挂烫衣物之前,确保衣物干燥而不潮湿。
潮湿的衣物不适合直接用蒸汽挂烫机烫烫。
将干燥的衣物挂在挂烫机提供的衣物挂钩上。
然后,将挂烫机的蒸汽喷嘴对准衣物上的皱纹处。
4.烫烫握紧挂烫机手柄,按下蒸汽开关开始喷蒸汽。
一般来说,挂烫机的喷嘴会喷出高温高压的蒸汽,能够迅速将衣物上的皱纹去除。
在使用过程中,要尽量保持喷嘴与衣物的垂直角度,并保持适当的距离,避免喷嘴过近导致衣物受到过热或燃烧。
5.注意事项使用蒸汽挂烫机时,有一些事项需要特别注意。
首先,使用过程中要确保蒸汽挂烫机的电源插头不与水接触,避免发生触电的事故。
其次,使用时要将挂烫机放置在安全的位置,并确保没有儿童或宠物靠近,以免发生意外。
另外,挂烫机使用后会产生一些热气和水蒸汽,所以在使用过程中要注意避免接触热气和蒸汽,以免烫伤皮肤。
最后,在使用完毕后,及时关闭蒸汽挂烫机的电源,待其完全冷却后再进行清洁和存放。
6.清洁与存放蒸汽挂烫机使用完毕后,需要进行清洁和存放。
首先,拔下电源插头,等待挂烫机冷却后,才能进行清洁作业。
清洁时,首先倒掉水箱中的水,在清洁水箱前可以加入洗涤剂,以去除蒸汽挂烫机中的污垢和残留物。
然后,用干净的湿抹布擦拭挂烫机外表面,确保清洁干净。
最后,将蒸汽挂烫机放置在干燥通风的地方,以便于下次使用。
以上就是蒸汽挂烫机的使用方法。
使用蒸汽挂烫机时一定要注意安全,保持适当的距离和角度,避免发生意外。
另外,定期进行清洁和维护,可以保证蒸汽挂烫机的寿命和使用效果。
挂烫机使用技巧挂烫机是近些年来才走进千家万户的生活,因为操作简单,使用便捷,在家庭生活中它逐渐取代了电熨斗,成为新一代的靓衣利器。
但是因为是新事物的原因,很多人用不太习惯,那么挂烫机的使用技巧有哪些呢?挂烫机的工作原理是通过机子内部的发热锅持续产生的高温蒸汽不断的接触织物穿透织物纤维组织,软化织物纤维,通过“拉”、“压”的动作使织物平整顺滑,恢复织物的自然状态。
挂烫机的使用技巧就从熨烫原理上来说,无非就是“拉”“压”的技巧以及熨烫前准备和熨烫时注意的要领。
1、加水要注意两点:①加水时最好加纯净水,锅胆发热纯净水杂质少不容易结成水垢,可以延长锅胆使用寿命,纯净水出来的蒸汽也不会损害衣物。
②不要向水箱里注入热水,不然会影响发热锅使用寿命。
2、将衣服固定在衣架上,裤子的话最好可以平放,或者是裤架棒固定。
单杆挂烫机通常不是很稳定,最好选用双杆的挂烫机。
华光的双杆就非常稳定,独特的架构设计可以轻松的熨裤子,熨裤线。
3、蒸汽挂烫机在熨裤子时,一般的可以用普通衣架挂在上面进行熨烫,并且最好戴上防烫手套。
4、烫衣服下摆时,抓住衣服两侧,拉紧进行压烫,警惕蒸汽喷头的热蒸汽。
(更方便的方式是运用夹板熨烫.不怕烫手又很好的把衣服烫好)。
5、在烫衣领时,一般要把领子翻过去,从背面进行熨烫,这样比较容易。
,可以用衣领小助手6、烫到衣服袖子的时候要稍微用力把袖子拉直,蒸汽喷头压在袖子折连的时光也要长一点,来回压烫。
7、熨衣服的时候注意一下功率,也就是档位问题,丝质的可以用小一点的功率,厚的可用大一点的功率。
熨完衣服后,衣服熨烫后不宜直接放到衣橱里,剩余的蒸汽会使衣物发霉,需要在外晾一段时间,衣服熨完后就穿很容易使衣服变皱,除非是用华光强力蒸汽系列的,熨过的衣服放在衣柜不宜放的太挤,否则容易起皱。
蒸汽挂烫机使用方法
使用蒸汽挂烫机的方法如下:
1. 准备工作:将蒸汽挂烫机放在平稳的地面上,并插上电源。
根据挂烫机的说明书,加入适量的清水。
等待一段时间,让水加热成蒸汽。
2. 准备衣物:挂烫机适用于轻度皱褶或需要杀菌的布料。
确保要挂烫的衣物上没有太多严重的皱褶,并清除可能的污渍。
3. 调整挂烫机设置:根据你要处理的衣物类型和皱褶程度,选择合适的温度和蒸汽量。
在挂烫机上通常会有相关的按钮或开关。
4. 开始挂烫:将挂烫机的喷头或蒸汽口对准衣物,保持一定的距离(一般为5-10厘米)。
用均匀的上下或左右移动的手势,将蒸汽挂烫机按压或扫过衣物的表面。
5. 注意安全:使用挂烫机时要注意保持安全距离,避免喷头接触皮肤或燃烧物品。
同时,也要小心不要让热蒸汽接触到眼睛。
6. 挂烫衣物的顺序:建议从内衣、袜子等布料较轻的衣物开始挂烫,然后再处理外套、裤子等较厚的衣物。
7. 完成后处理:挂烫完毕后,等待衣物完全干燥之后再穿上。
同时,注意挂烫
机的使用和清洁方法,以保持其性能和寿命。
注意事项:
- 仔细阅读和按照蒸汽挂烫机的使用说明操作,避免不正确的使用造成危险。
- 注意水位和水温的控制,避免因加水不足或过热而损坏挂烫机。
- 使用挂烫机时要小心烫伤,尤其是在处理衣物时要注意保持距离。
- 在使用挂烫机时,切勿将喷头对准人体,特别是眼睛等敏感部位。
- 注意在使用时保持周围的通风,在停止使用之前,要先把挂烫机关机,等冷却后才能移动或存放。
- 不要将蒸汽挂烫机用于不适合的衣物材质,以免造成衣物损坏。
Applicable model: XG-0301Handheld Garment Steamer Operation ManualPlease carefully read this manual before using the product.Dear customer,Thank you for choosing our handheld garment steamer. This product is simplefor operation, light , portable and has strong functions. It helps to remove wrinkles and dusts on garment and may bring you to an new garments care experience in future travel.Important Safety InstructionsWhen using your appliance, basic precautions should always be followed, including thefollowing:1. Please carefully read this manual before use.2. Please use this machine as per the purpose specified in this manual and do not use it for other purpose.3. To avoid electric shock and other hazards, don't immerse this machine, power cord and the plug into water.4. Never yank cord to disconnect from outlet. Please hold the plug and pull it out of the socket gently. Your hand must be dry.5. Don't fill the machine with hot water or add any corrosive cleanser in water; otherwise, the machine may be damaged. It is recommended to use minerals free water .6. Always disconnect from electrical outlet when the garment steamer is not in use, or when adding water into the water tank or when there is no water in the water tank.7. When the power supply or the machine is damaged, don't run this product. To avoid electric shock, don't try to dismantle or repair this machine. Send it to a qualified repair center for inspection and repair. Private dismantling, repair or replacement may lead to hazards of a fire,8. Don't let the product running in an unattended area. Immediate turn off the power while if childis attempts to use or approach this product. Close supervision is necessary for any appliancebeing used by or near children.9. Exposure to the panel at the steam outlet or the exposure to steam may lead to scalding. Pay attention to safety when put the garment steamer upside down.10. Beware high temperature steam while using this product. To minimize hazards of exposureto hot steam, please don't point the steamer to any person or pet when using this product.11. The product must be use under supervision or guidance of well knowledge personal, andstraightly forbidden as toy for children.12. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. Loop cord loosely around appliance when storing.13. DO NOT use this product if the power cord is damaged, consult with manufacturer or the service provider, or local sales dealer.14. Please consult to local government for recycling by law, DO NOT dump this product into general waste!15. To reduce the risk of contact with hot water emitting from steam vents, check appliance before each use by holding it away from body and operating steam button.Save These InstructionsTo reduce the likelihood of circuit overload, do not operate another high wattage appliance onthe same circuit.If an extension cord is absolutely necessary, a (ampere rating of the appliance) ampere ratedcord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over.Product schematic diagram1. Trouser clamp2. Fine hair brush3. Long hair brush4 14.Steam jet5. Switch6. Indicator576 27. Main machine8.Water tank 3 8 SpecificationsRated voltage: 110-120V~ Rated frequency: 60Hz Rated power: 860W Water tank capacity: 320mlWater filling1 2 3 4Disconnect power supply Counterclockwise turning Take out the water tank Remove the silicon plug5 6 7 8Fill up water in 80% full level Insert the silicon plug Direct the trigangle atClosewise turning for lockingthe lineNote:Normal tap water may be used for this product. However, if water hardness at yourarea is too high, limescale may quickly be generated. Therefore, it is recommendedto add distilled water in the tank to extend service life of the product. Don't add anycorrosive liquid or cleanser in water to avoid product damage.Start-upNote:To extend p roduct service life, water lacking shall be avoided! When the steam is insufficient, please pull off the power supply and add water.1 2324SInstall the water tank, Connect to power supply.Press the switch; the indicator will be on in red and then change to blue after 24s of preheating. Steam will be supplied automatically.counterclockwise turn the steam jet by 180 degrees.4 5Press the switch again; indicator off; no more steam out.Pull out the plug; work stops.Steaming operation1. Before using the garment steamer, add water in the water tank by the method specified above.2. Counterclockwise turn the steam jet by 180 degrees (see Fig. 1); connect to power supply andpress the switch to start steaming.3. During steaming, don't touch the steam jet. Keep it at least 20cm away from your body to avoid scalding.4. Don't direct steam at anybody.5. Before steaming, pull the garment straight to facilitate steaming. Garment with fewer wrinkles is relatively easy for steaming while more wrinkles require repeated steaming.6. This product is not suitable for plat or inverted steaming (see Fig. 2 and Fig. 4); move the steamjet up and down (see Fig. 5 and Fig. 7) to facilitate wrinkle removing.7. When moving the steam jet, pul l flat the garment for steaming gently to achieve better steaming effect.1 2 3 45 6 7Trouser clamp and brush installationNote: be sure to disconnect the power before trouser clamp and brush is attached or dismantling. Pay attention that the steam jet may still be very hot and you should wait it for cooling done before attach or remove any accessory. For accessory installing, pay attention to the direction to avoid blocking steam ejecting holes. The arrow on the accessory must be direct at the triangle on the steam jet. Maintain consistent direction.Trouser clampThe trouser clamp helps for steam penetration into thick fiber for quicker styling.Fine hair brushThe fine hair brush may remove static and fiber and hair on the garment.Direct card positions on both sides and press down. Installation completed. Direct card positions onInstallation completed.both sides and press down.Long hair brushThe long hair brush may remove dust and dirt. Don't apply the brush for gentle fabric, such as silk or satin.Fine hair brush Long hair brushDirect card positions onboth sides and press down.Installation completed.Cleaning and maintenanceNote: don't clean this product with steel wool, abrasive cleanser or corrosive liquid(such as alcohol, gasoline or acetone. It shall be cleaned by wet cloth and non-corrosiveliquid; wipe away sediments in the steam jet.Remove residual water in the tank completely. Wait for cooling of the machine beforeput it inside the package.1 2 31.5 hoursDisconnect power supply. Wait for cooling before cleaning(Wait for 1.5 hours for cooling) Remove sediments inthe steam jet.4 5Remove water completely. Pack in the carton.Fault analysisCommon faults Causes SolutionNo power connection Insert the plug into the socketPress the steam switch completelyFail to press the steam switch fullyWater level in the tank is too low The water tank is not properly placed Pull of the plug and add water in the tank Install the tank correctlyNo steam going outof the garment steamerThe machine is inversed thus leadingto the failure of water suctionUse the machine correctlyIf it is not the above reason, it maybe the fault of the machineSend to the repair department for repairWater ejecting when starts up the machineThis phenomenon will disappear after 24s ofpreheatingInadequate preheating timeWater ejecting in the midway Water out in little amount underpressureThis is the normal phenomenonWater pumping sound/ handle vibration of the garment steamer Vibration generated by the electricpumpThis is the normal phenomenonProduct Warranty CardPurchasing dateName/ unitTelephoneAddress(MM/DD/YY) FaxMachine No.CityModel E-mailRepair records- If you need services or information, please contact related distributors.- Warrant services will be provided only in the effective warranty term under normal using situation. In case of any fault due to the problem of the product rather than any artificial reason, warranty services may be enjoyed. The following situations are not in the warranty scope:1. Damage caused by disassembly by any one not undertaking the warranty services.2. Damage of the machine due to artificial reason.3. Damage caused by the failure to correctly use, maintain and repair the machine as per the operation manual.4. Damage caused by falling down, squeezing, water immersing and other personal mistake.5. Damage caused by flood, fire, lightning and other force majeure event.6. Damage accidentally caused by the purchaser.7. Please properly keep this warranty card which shall be provided in order to enjoy warranty services. The warranty card shall not be altered; otherwise, it will be invalid.。
1、注水初次使用时,请注入自来水。
再次注入时仍可用自来水。
不过,如水质太硬,则建议您使用蒸馏水注水前,请先将插头拔掉,将蒸汽钮旋转至无蒸汽的位置。
将熨斗竖起,然后注入水孔内注入150毫升的水,请用注水杯注水。
2、接通电源将温度旋钮旋至关的位置。
将插头插入220v~插座中。
3、温度设定将温度旋钮转至与衣物一致的位置,直到电源指示灯灭。
4、喷水功能取量杯注入200ml水至水箱中。
将喷水/强力蒸汽旋钮至“喷水”的位置。
按下喷水按钮3-5次,即可喷水。
5、蒸汽功能取量杯注入200ml水于水箱中。
使用蒸汽时,温度旋钮必须处于蒸汽区的位置,电源指示灯熄灭后,将蒸汽旋钮至顾客所需的蒸汽区域顾客可随意调节。
6、强力蒸汽功能使用强力蒸汽时,将温度旋钮旋至“麻”的区域,蒸汽旋钮旋至将喷水/强力蒸汽旋钮转至“爆炸”的位置待电源指示灯熄灭后,按下强力蒸汽按钮,就会产生强力蒸汽。
7、垂直蒸汽功能垂直蒸汽是一种简单又方便的烫衣方法。
强力蒸汽使蒸汽直向输出,无须用熨依板就能令衣物烫得贴服自然,是处理西装、处套的必然选择。
使用垂直蒸汽时,将温度旋钮至“麻”的区域,蒸汽旋钮至位置。
待指示灯熄灭后,将熨斗竖放贴进挂着的衣服,按下强力蒸汽按钮,即产生垂直蒸汽。
8、防钙当水份中钙含量比较大时,容易使水箱内产生水垢,离子交换树脂就会把水份中的钙离子中和,使水箱内不易产生水垢。
在使用了一段时间后,往水箱里加入一定浓度的盐水。
放置5分钟后,轻微摇晃再把水从注水口把水倒掉,就可以清洁干净水箱内的水垢了。
9、清洗功能把蒸汽旋钮至关闭档,装水满水位,并设定温度为最大档,插上电源开始加热至电源指示灯灭后拔掉插头,将熨斗拿至洗手台开到清洗档,至水渥干后,再插上电源,烘干水份,然后拔掉插头,待熨斗冷却后收藏。
10、存放熨斗完毕后,将水箱中剩余水倒出,温度旋钮旋至“麻”的位置,得新接通电源,烧干蒸汽腔中的残留水份,然后待电源指示灯灭后,将温度旋钮设在关的位置,拔掉电源,待电热盘冷却后即可保存。
如何使用电动挂烫机电动挂烫机是一种非常方便的小型家电,特别适合使用在家庭中,帮助我们把衣服熨平并放置整齐。
使用电动挂烫机可以让我们的衣服焕然一新,有趣又实用。
1. 准备工作在使用电动挂烫机之前,我们需要先做一些准备工作。
首先,清洁好电动挂烫机的表面,以确保其正常运行。
其次,将电动挂烫机放在一块平整的表面上,并插上电源线。
接着,我们需要准备好需要熨烫的衣物,并将其摆在电动挂烫机旁边的桌子上,以便在使用时更加方便。
最后,在使用前需要让电动挂烫机预热几分钟,以确保其可以正常工作。
2. 开始使用当电动挂烫机已经预热好之后,我们可以开始进行电动挂烫了。
首先,我们需要将需要熨烫的衣物挂在挂烫机上,然后轻轻地按下电源开关,启动电动挂烫机。
接着,我们可以调节热度和水汽的大小,以便更好地进行挂烫。
我们可以从衣物的底部向上进行挂烫,保持恒定的速度和压力,以确保我们所使用的电动挂烫机可以平稳地工作。
如果需要熨烫裤子或者长袖衬衫这类衣物时,我们可以移除挂烫机上的夹子,并直接用手将衣物放置在挂烫板上,然后进行挂烫。
3. 安全使用使用电动挂烫机时,我们需要注意一些安全事项。
首先,我们需要保持电动挂烫机和水源保持一定的距离,并避免将电动挂烫机放在潮湿或者易燃的地方。
另外,在使用挂烫机时,我们需要保持电动挂烫机和其他人的距离,以免发生意外。
最后,在使用电动挂烫机时,我们需要随时注意挂烫板的温度,以免发生烫伤。
总之,使用电动挂烫机是一种非常方便的方法,可以让我们轻松地将衣服挂烫平整。
在使用时,我们需要准备好所需要的衣物、让电动挂烫机预热好、确保使用安全等几个步骤,以确保电动挂烫机可以正常工作,并帮助我们轻松将衣服熨平。
挂烫机正确使用方法挂烫机是一种非常方便的家用电器,可以帮助我们快速熨烫衣物,让衣物焕然一新。
但是,如果不正确使用挂烫机,可能会导致烫坏衣物或者安全事故。
因此,正确的使用方法非常重要。
下面,我将为大家介绍挂烫机的正确使用方法,希望能帮助大家更好地使用这一家电器。
首先,使用挂烫机之前,需要确保挂烫机的水箱中注满了清水。
水箱注水时,要确保电源已经关闭,以免发生电器短路。
另外,要选择适量的水量,不要过多或者过少,以免影响挂烫机的正常工作。
接下来,将挂烫机插入电源插座,打开电源开关,等待挂烫机预热。
预热时间一般为1-2分钟,待挂烫机指示灯亮起后,表示挂烫机已经预热完毕,可以开始使用了。
在等待预热的过程中,可以将需要熨烫的衣物挂在挂烫机上,为熨烫做好准备。
开始熨烫时,要将衣物平整地挂在挂烫机上,不要让衣物皱折。
然后,按下蒸汽开关,蒸汽会从挂烫机的喷嘴中喷出,对衣物进行熨烫。
在使用过程中,要保持挂烫机与衣物的距离适当,不要让挂烫机直接接触衣物,以免烫坏衣物。
在熨烫过程中,可以根据衣物的材质和厚薄,调节挂烫机的温度和蒸汽量。
一般来说,厚重的衣物需要更高的温度和蒸汽量,而薄轻的衣物则需要较低的温度和蒸汽量。
在调节温度和蒸汽量时,要按照挂烫机的说明书上的指引进行,以免调节不当导致衣物烫坏或者挂烫机损坏。
当熨烫结束后,要先关闭蒸汽开关,然后拔掉电源插头,等待挂烫机冷却后再进行清洁和存放。
清洁时,要注意不要用尖锐的物体刮擦挂烫机的喷嘴,以免损坏喷嘴造成故障。
存放时,要将挂烫机放置在干燥通风的地方,远离水源和火源,以免发生安全事故。
总的来说,正确使用挂烫机需要注意以下几点,注满适量的清水、预热完毕后再开始使用、调节合适的温度和蒸汽量、熨烫结束后及时关闭电源和清洁存放。
只有正确使用挂烫机,才能更好地保护衣物和自己的安全。
希望大家在使用挂烫机时能够严格按照以上方法进行,让挂烫机成为我们生活中的好帮手。
蒸汽挂烫机的使用方法
使用蒸汽挂烫机的步骤如下:
1. 准备工作:确保挂烫机中的水箱已装满水。
根据挂烫机的说明书,将挂烫机放在平稳的地面上,并将电源插头插入电源插座。
2. 加热挂烫机:打开挂烫机的电源开关,开始加热。
一般来说,挂烫机需要几分钟的时间来加热水箱中的水并产生蒸汽。
在等待过程中,你可以准备需要熨烫的衣物。
3. 设置挂烫机:根据衣物的材质和需要的熨烫温度,将挂烫机的温度和蒸汽输出调节到合适的位置。
根据挂烫机的类型,你可能需要调节温度旋钮或按钮来达到所需的熨烫温度。
4. 开始熨烫:等待挂烫机完全加热后,将需要熨烫的衣物放在挂烫机下方的烫板上,轻轻地按下挂烫机的蒸汽按钮或扳动蒸汽开关。
此时,挂烫机会释放出热蒸汽,通过衣物的纤维,去除皱褶。
5. 熨烫小面积部分:对于较大型的衣物,如衬衫或裙子,使用挂烫机时,从一个小区域开始熨烫,然后逐渐移动到衣物的其他区域。
记得不要在同一个地方停留太久,以免熨烫过度或损坏衣物。
6. 结束熨烫:熨烫完毕后,关闭挂烫机的电源开关,并将电源插头从电源插座拔出。
在挂烫机冷却之前,不建议打开水箱或倒入水。
7. 清洁和存放:等待挂烫机完全冷却后,使用干净的湿布或纸巾擦拭烫板和挂烫机的其他部分,以清除任何残留的水渍或灰尘。
然后将挂烫机妥善存放在干燥的地方。
请注意,具体的使用步骤可能因挂烫机的品牌和型号而有所差异,建议在使用前阅读挂烫机的说明书,并按照说明书中的指示操作。