奎克化学（中国）有限公司 高压喷淋低泡清洗剂QUAKERCLEAN 624CPT

CANBERRA CORPORATIONSAFETY DATA SHEET1. IdentificationProduct Identifier: HUSKY 1255 FOAMING OVEN & GRILL CLEANERApplication or recommended use: Oven cleanerRestrictions on use: Do not use in any fashion not specified on the product label.Manufacturer / supplier: Canberra Corporation3610 N. Holland-Sylvania Rd.Toledo, Ohio 43615 USATelephone: 419-841-6616Emergency phone: 866-836-88552. Hazards IdentificationGHS Classification: Classification of this mixture in accordance with paragraph (d) of §1910.1200.Flammable Aerosols - Category 1Skin corrosion/irritation - Category 1Serious eye damage/eye irritation - Category 1Label Elements:Symbol:Signal word: DANGERHazard statements: Extremely flammable aerosol. Causes severe skin burns and serious eye damage.Precautionary statements: Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Washthoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection.IF INHALED: Remove person to fresh air and keep comfortable for breathing.IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediatelyall contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air andkeep comfortable for breathing.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present andeasy to do. Continue rinsing. Immediately call a poison center/doctor. Wash contaminated clothingbefore reuse.See 4. First-Aid Measures for specific treatment.Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.Dispose of contents/container to an approved disposal facility.Other Hazards: None known.3. Composition / Information on IngredientsChemical characterization: Mixture of water, alkali, solvents and auxiliary agents.Hazardous ingredients: The exact percentage of composition has been withheld as a trade secret.2 - 10% Diethylene Glycol Monobutyl Ether CAS 112-34-52 - 10% Sodium Hydroxide CAS 1310-73-22 - 10% Butane CAS 106-97-81 - 3% Propane CAS 74-98-64. First-aid measuresInhalation: Remove person to fresh air and keep comfortable for breathing. Call a physician if symptoms develop or persist.Skin contact: Take off immediately all contaminated clothing. Rinse skin with water/shower. Call a physician/poison control center immediately. Chemical burns must be treated by a physician. Wash clothing separately before reuse.Eye contact: Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.Ingestion: Call a physician or poison control center immediately. Rinse mouth. Do NOT induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs.Most important symptoms/effects, acute and delayed: Burning pain and severe corrosive skin damage. Causes serious eye damage. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage could result. Indication of immediate medical attention and special treatment needed: Provide general supportive measures and treat symptomatically. Chemical burns: Flush with water immediately. While flushing, remove clothes which do not adhere to affected area. Continue flushing during transport to hospital. Keep victim under observation. Symptoms may be delayed.5. Fire-fighting measuresSuitable extinguishing media: Water fog. Foam. Dry chemical. Carbon dioxide (CO2).Unsuitable extinguishing media: Do not use water jet as an extinguisher, as this will spread the fire.Specific hazards arising from the chemical: Contents under pressure. Pressurized container may explode when exposed to heat or flame. During fire, gases hazardous to health may be formed.Special protective equipment and precautions for firefighters: Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, and rubber boots.Fire-fighting equipment/instructions: Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.Specific methods: Use standard firefighting procedures and consider the hazards of other involved materials. Move containers from fire area if you can do so without risk. In the event of fire and/or explosion do not breathe fumes.General fire hazards: Extremely flammable aerosol.6. Accidental release measuresPersonal precautions, protective equipment and emergency procedures: Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them.Methods and materials for containment and cleaning up: Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until gas has dispersed. Prevent entry into waterways, sewer, basements or confined areas. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.Environmental precautions Avoid discharge into drains, water courses or onto the ground.7. Handling and storagePrecautions for safe handling: Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Avoid contact with skin, eyes and clothing. All equipment used when handling the product must be grounded. Use non-sparking tools and explosion-proof equipment. Do not get in eyes, on skin, or on clothing. Avoid breathing fume/gas/mist/vapors/spray. Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Observe good industrial hygiene practices.Conditions for safe storage, including any incompatibilities: Level 1 Aerosol.Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store away from incompatible materials.8. Exposure controls/personal protectionOccupational exposure limitsUS. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)Components Type ValuePropane (CAS 74-98-6) PEL 1800 mg/m3 (1000 ppm)Sodium Hydroxide (CAS 1310-73-2) PEL 2 mg/m3US. ACGIH Threshold Limit ValuesComponents Type Value FormButane (CAS 106-97-8) STEL 1000 ppmDiethylene Glycol Monobutyl Ether (CAS 112-34-5) TWA 10 ppm Inhalable fraction and vapor.Sodium Hydroxide (CAS 1310-73-2) Ceiling 2 mg/m3US. NIOSH: Pocket Guide to Chemical HazardsComponents Type ValueButane (CAS 106-97-8) TWA 1900 mg/m3 (800 ppm)Propane (CAS 74-98-6) TWA 1800 mg/m3 (1000 ppm)Sodium Hydroxide (CAS 1310-73-2) Ceiling 2 mg/m3Appropriate engineering controls: Explosion-proof general and local exhaust ventilation. Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency shower must be available when handling this product. Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.Individual protection measures, such as personal protective equipmentEye/face protection: Wear safety glasses with side shields (or goggles) and a face shield. Do not get in eyes.Hand protection: Wear appropriate chemical resistant gloves.Other: Wear appropriate chemical resistant clothing.Respiratory protection: If permissible levels are exceeded use organic vapor cartridge or an air-supplied respirator.General hygiene considerations: When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.9. Physical and chemical propertiesAppearancePhysical state: Gas. Form: Aerosol.Color: Colorless. Odor: Characteristic.Odor threshold: Not available. pH: 13 - 14Melting point/freezing point: Not available. Initial boiling point/boiling range: 212 °F (100 °C) estimated.Flash point: -156.0 °F (-104.4 °C) Propellant estimated.Evaporation rate: Not available. Flammability: Not available.Upper/lower flammability or explosive limitsFlammability limit – lower (%): Not available. Flammability limit – upper (%): Not available.Explosive limit - lower (%): Not available. Explosive limit - upper (%): Not available.Vapor pressure: 27.3 psig @70F estimated Vapor density: Not available.Relative density: Not available. Solubility (water): Not available.Partition coefficient (n-octanol/water): Not available.Auto-ignition temperature: Not available. Decomposition temperature: Not available.Viscosity: Not available. Specific gravity: 0.664 estimated10. Stability and reactivityReactivity: Reacts violently with strong acids. This product may react with oxidizing agents.Chemical stability: Material is stable under normal conditions.Possibility of hazardous reactions: None known under conditions of normal use. Hazardous polymerization does not occur. Conditions to avoid: Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point. Do not mix with other chemicals. Contact with incompatible materials. Fire or intense heat may cause violent rupture of packages. Incompatible materials: Acids. Strong oxidizing agents.Hazardous decomposition products: No hazardous decomposition products are known.11. Toxicological informationInformation on likely routes of exposureIngestion: Causes burns. Ingestion may cause severe irritation and burns of the mouth, the esophagus and the gastrointestinal tract. Inhalation: May cause irritation to the respiratory system. Prolonged inhalation may be harmful.Skin contact: Causes severe skin burns. Eye contact: Causes serious eye damage.Symptoms related to the physical, chemical and toxicological characteristics: Burning pain and severe corrosive skin damage. Causes serious eye damage. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including blindness could result. Causes severe eye damage.Information on toxicological effectsAcute toxicity: Expected to be a low hazard for usual industrial or commercial handling by trained personnel.Acute Species Test ResultsDermal LD50 Rat 15720 mg/kgInhalation LC50 Rat 3940 mg/l/4hSerious eye damage/eye irritation: Causes serious eye damage.Respiratory sensitization: Not a respiratory sensitizer. Skin sensitization: This product is not expected to cause skin sensitization. Carcinogenicity: This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050): Not listed.Reproductive toxicity: This product is not expected to cause reproductive or developmental effects.Specific target organ toxicity - single exposure: Not classified.Specific target organ toxicity - repeated exposure: Not classified.Aspiration hazard: Not an aspiration hazard. Not likely, due to the form of the product.Chronic effects: Prolonged inhalation may be harmful.12. Ecological informationEcotoxicity: The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.Persistence and degradability: No data is available on the degradability of this product.Bioaccumulative potential: No data available.Partition coefficient n-octanol / water (log Kow): Butane 2.89; Diethylene Glycol Monobutyl Ether 0.56; Propane 2.36Mobility in soil: No data available.Other adverse effects: No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component.13. Disposal considerationsDisposal instructions: Collect and dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not puncture, incinerate or crush. Dispose of contents/container in accordance with local/regional/national/international regulations. Waste from residues/unused products: Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner.Contaminated packaging: Empty containers should be taken to an approved waste handling site for recycling or disposal. Emptied containers may retain product residue, follow label warnings even after container is emptied.14. Transport informationDOT UN number: UN1950 UN proper shipping name: Aerosols, flammable Class: 2.1 Transport hazard class Subsidiary risk: 8Label(s): 2.1, 8 Packing group: Not applicable.Special precautions for user: Read safety instructions, SDS and emergency procedures before handling.Packaging exceptions: This product meets the exception requirements of section 173.306 as a limited quantity and may be shipped as a limited quantity.15. Regulatory informationUS federal regulationsThis product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.All components are on the U.S. EPA TSCA Inventory List.TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D): Not regulated.CERCLA Hazardous Substance List (40 CFR 302.4): Sodium Hydroxide (CAS 1310-73-2) Listed.SARA 304 Emergency release notification: Not regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050): Not listed.Superfund Amendments and Reauthorization Act of 1986 (SARA): Hazard categories:Immediate Hazard – Yes Delayed Hazard – NoFire Hazard – Yes Pressure Hazard – NoReactivity Hazard - NoSARA 302 Extremely hazardous substance: Not listed.SARA 311/312 Hazardous chemical: NoSARA 313 (TRI reporting): Not regulated.Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List: Not regulated.Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130):Butane (CAS 106-97-8) Propane (CAS 74-98-6)Safe Drinking Water Act (SDWA): Not regulated.US state regulationsUS. Massachusetts RTK - Substance ListUS. New Jersey Worker and Community Right-to-Know ActUS. Pennsylvania Worker and Community Right-to-Know LawUS. Rhode Island RTKButane (CAS 106-97-8) Propane (CAS 74-98-6) Sodium Hydroxide (CAS 1310-73-2)US. California Proposition 65: California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins.16. Other information, including date of preparation or last revisionDate issued: 05. 01. 2015 HSK-1255 Revision: N/AVersion #01Disclaimer The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.。

化学品安全技术说明书产品名称: 清洁剂 KRONES colclean EV60修订日期: 2020年08月20日最初编制日期: 2020年08月20日依据GB/T 16483、GB/T 17519编制版本: 1.0第 1 部分化学品及企业标识化学名称 (中文名): 清洁剂 KRONES colclean EV 60化学名称 (英文名) : Cleaning agent KRONES colclean EV 60企业名称: KIC KRONES Internationale Cooperationsgesellschaft mbH 地址: Böhmerwaldstraße 5邮政编码: 93073 Neutraubling电话号码: +49-940170-3020传真: +49-940170-3696电子邮件地址: ******************进口商: KRONES Trading (Taicang) Co. Ltd.地址: No. 9 Ning Bo Dong Lu邮编: 215400 Taicang Jiangsu Suzhou电话号码: +86 512 5373 9300电子邮件地址: **************.com应急咨询电话: +86 400 120 6011 (NCEC, National Chemical EmergencyService)0532-8388-9090 (NRCC National Registration Centre forChemicals)建议用途: 用作清洁剂。

使用限制: 无相关信息。

第 2 部分危险性概述紧急情况概述无色液体，轻微的气味。

可燃液体；吞咽及进入呼吸道可能致命。

GHS 分类物理性危险: 易燃液体类别4健康危害: 吸入危害类别1上述未涉及的其他危险性，分类不适用或无法分类标签要素象形图 (GHS CN) :警示词 (GHS-CN) : 危险。

专业的工业污垢清洗剂、金属防锈润滑剂、切削加工液系列产品生产供应商华阳-恩赛有限公司（中美合资）网址：地址：CHINA电话：-（山东分公司孙先生）总部地址：辽宁省大连市金州新区双D港1986年春，美国NCH公司和中国华阳技术贸易集团在大连合资创建了第一家中美合资企业——华阳-恩赛有限公司。

华阳恩赛一贯坚持把美国NCH公司的先进技术、科学管理和现代经营理念与中国实际有机融合，全方位向中国工业设备维护维修和机械零部件加工领域提供专用化学品；大批的高级管理、研发人才和高素质员工，以及遍布全国各中心城市、工业城市的分支机构和销售网络，使她在中国大陆始终处于行业龙头地位，成为国内专业性最强、影响最广、规模最大的设备维护化学品、零件工序化学品及其相关产品供应商。

20多年来，华阳恩赛在打造中国专用化学品著名品牌的过程中，还创造了无数个中国第一，它们是：第一个在中国引进工业品直销经营模式的公司；第一个在中国实行全天候销售和技术服务的公司；第一个在中国推介TPM全面生产维护概念的公司；第一个在中国导入设备全系列维护化学品的公司；第一个在中国供应航空飞行器维修化学品的公司；第一个在中国拥有零件工序全系列化学品的公司；第一个在中国经营期限达75年的中美合资公司；第一个在中国通过ISO9001:2000的业内公司；第一个在中国配套现场应用增值方案的业内公司；第一个在中国应用Oracle管理软件的业内公司；第一个在中国开展全员职业大学教育的业内公司；第一个在中国实现年产量达10万吨的业内公司；……华阳恩赛严格执行与NCH公司签订的《许可证和技术合作协议》，不断推出技术先进、性能优良、质量稳定、使用简便、安全可靠的：设备维护化学品（设备维护化学品——清洗剂、防锈剂等；飞机维修化学品——清洗剂；循环水处理药剂——阻垢剂、杀菌剂、分散剂等），广泛应用于航空航天、机电加工、石油化工、钢铁制造、能源动力、交通运输、电信通讯等行业的机械设备清洗、防锈、维护保养处理；零件工序化学品（金属加工液——全合成液、微乳液、全乳液等；零件工序化学品——清洗剂、防锈剂等），集中应用于航空航天、机电加工、军工制造、电子产品、信息通讯、仪器仪表、光学器材、交通运输、机械设备、能源动力、原材料生产等领域的零部件和原材料机械加工过程中的润滑、冷却、净洗、防锈。

化学品安全技术说明书科波西电子材料张家港有限公司按照GB/T 16483、GB/T 17519编制产品名称:MOLYKOTE® G-快速润滑喷剂 / MOLYKOTE® G-Rapid SpraySDS编号:3142141最初编制日期:30.07.2015发行日期:02.01.2019打印日期:23.06.2023科波西电子材料张家港有限公司鼓励并希望您能阅读和理解整份(M)SDS，该文件包括了重要的信息。

我们希望您能遵从该文件给出的预防措施，除非你的使用条件需要其他更合适的方法或措施。

一化学品及企业标识产品名称:MOLYKOTE® G-快速润滑喷剂MOLYKOTE® G-Rapid Spray推荐用途和限制用途已确认的各用途:润滑剂和润滑添加剂公司名称:科波西电子材料张家港有限公司扬子江国际化学工业园南京路3号215633 江苏省张家港市中国客户咨询方式:86-512-5561 1616*************************传真：86-21-3862 2896应急咨询电话24-小时应急联系电话:************国内应急电话:************二危险性概述紧急情况综述外观与性状含溶解气体的气雾剂颜色深灰气味略微的极易燃气溶胶。

压力容器：遇热可爆。

造成皮肤刺激。

对水生生物有害。

对水生生物有害并具有长期持续影响。

®™杜邦公司关联公司的商标。

页 1 的 18GHS危险性类别根据法规的标准, 被列为有害品。

气溶胶 - 类别 1皮肤腐蚀/刺激 - 类别 2急性（短期）水生危害 - 类别 3长期水生危害 - 类别 3GHS标签要素象形图信号词:危险!危险性说明极易燃气溶胶。

压力容器：遇热可爆。

造成皮肤刺激。

对水生生物有害并具有长期持续影响。

防范说明预防措施远离热源/火花/明火/热表面。

禁止吸烟。

切勿喷洒在明火或其他点火源上。

切勿穿孔或焚烧，即使不再使用。

化学品安全技术说明书No-Clean Flux Remover Pen符合GB/T 16483-2008和GB/T 17519-2013规定化学品标识产品名称No-Clean Flux Remover Pen产品编号MCC-DC1PEN化学品的推荐用途和限制用途推荐用途清洗剂。

供应商的详细情况供应商MICROCARE ASIA PTE LTD102E, Pasir Panjang Road,Citilink, #05-06,Singapore 118529(65)6271.0182制造商MICROCARE LLC595 John Downey DriveNew Britain, CT 06051United States of AmericaCAGE: OATV9Tel: +1 800-638-0125, +1 860-827-0626应急咨询电话应急咨询电话INFOTRAC 4001-200761 (CHINA)1-352-323-3500 (from anywhere in the world)紧急情况概述外观液体。

颜色透明液体。

无色的。

气味轻微的。

乙醚。

GHS 危险性类别物理危险易燃液体 类别2健康危害非此类环境危害危害水生环境 一急性危险 类别1健康危害若此品溅射到眼睛，会引起红斑和眼睛过激。

存放在儿童够不着的地方。

请参见第11部分以了解关于健康危害的更多信息。

物理危险产品高度易燃。

蒸气可能会与空气形成爆炸性混合物。

标签要素象形图警示词危险危险性说明H225 高度易燃液体和蒸气。

H400 对水生生物毒性极大。

防范说明预防措施P210 远离热源/ 热表面/ 火花/明火/ 其他点火源。

禁止吸烟。

P240 容器和接收设备接地/ 等势联接。

P242 只能使用不产生火花的工具。

P243 采取防止静电放电的措施。

P273 避免释放到环境中。

事故响应P370+P378 火灾时：使用泡沫、二氧化碳、干粉或水雾灭火。

SAFETY DATA SHEETD-167 INDUSTRIAL PRESSURE WASHER DETERGENT 1. IDENTIFICATIONProduct Code :D-167Product Name : Industrial Pressure Washer DetergentPackaging Size : 4 L Jug (4 x 4 L in one case)Packaging Code : 8582116Synonyms : NoneRecommended Use : Detergent for Cleaning and DegreasingRestrictions on Use : For Industrial and Commercial Use OnlySupplier Identifier : Aaladin Superior Cleaning Systems, Ltd.71 Don Valley ParkwayPO Box 62052 Transcona RPOWinnipeg, MB R2C 5G2CanadaPhone: (204) 663-6618 Fax: (204) 663-3125Emergency Telephone Number (CANUTEC): (613) 996-66662. HAZARD IDENTIFICATIONClassification: Acute toxicity, oral (Category 4)Symbol:Signal Word: WarningHazard Statements: ∙May cause irritation to eyes, skin and lungs.∙Harmful if swallowed,Precautionary Statements: ∙Wear protective gloves/protective clothing/eye protection/face protection. ∙Wash face, hands and exposed skin with plenty of water after handling. ∙Do not eat, drink or smoke when handling this product.∙Do not breathe mist/vapor.∙Call immediate medical attention when severely exposed.Other Hazards NotClassified:Not Applicable3.4. FIRST-AID MEASURESFirst Aid Measures by Route of Exposure:Inhalation: Move victim to fresh air. Seek medical attention if adverse effects occurs.Skin Contact: Wash the affected area with plenty of slow flowing water. If irritation persists, seek medical attention.Eye Contact: Wash eye with plenty of water until irritation is gone. Seek medical attention if irritation persists.Ingestion: May cause upset stomach. Drink plenty of water to dilute. Seek medical attention.First Aid Comments: All first aid procedures should be periodically reviewed by a doctor familiar with the chemical and its conditions of use in the workplace.Most Important Symptoms and Effects (acute or delayed): Not AvailableImmediate medical attention and special treatment needed, if necessary: Treat symptomatically.5. FIRE-FIGHTING MEASURESSuitable Extinguishing Media: Not combustible. Use extinguishing agent suitable for surrounding fire.Unsuitable Extinguishing Media: Not ApplicableSpecific Hazards Arising from the Chemical: Toxic sodium oxide fumes can be generated at high temperatures.Hazardous Combustion Products: Not ApplicableSpecial Protective Equipment and Precautions for Fire-Fighters: Wear self-contained breathing apparatus and full protective gear.6. ACCIDENTAL RELEASE MEASURESPersonal Precautions: Remove or isolate incompatible materials as well as other hazardous materials.Methods for Containment and Clean-up: Contain and soak up spill with absorbent that does not react with spilled product. Flush spill area. Dike spilled product to prevent runoff.7. HANDLING AND STORAGEPrecautions for Safe Handling: Wear protective equipment. Ensure adequate ventilation. Keep away from heat, sparks, open flame and direct sunlight. Keep containers tightly closed when not in use or empty. Do not eat, drink or smoke while handling this product.Conditions for Safe Storage: Store in an area that is: cool, dry, well-ventilated, separate from incompatible materials. Keep amount in storage to a minimum. Store in the original, labelled shipping container. Vent drums to prevent pressure buildup. Do not handle swollen drums. Get expert advice.8. EXPOSURE CONTROLS/ PERSONAL PROTECTIONControl parameters, including occupational exposure guidelines or biological exposure limits and the source of those values:No exposure limitsAppropriate Engineering Controls: Use a local exhaust ventilation and enclosure, if necessary, to control amount in the air. Exhaust directly to the outside, taking any necessary precautions for environmental protection. Eye wash facility and emergency shower must be available when handling this product.Individual Protection Measures:Eye/Face Protection: Wear chemical safety goggles. A face shield (with safety goggles) may also be necessary.Skin Protection: Wear chemical protective clothing e.g. gloves, aprons, boots.9. PHYSICAL AND CHEMICAL PROPERTIESPhysical State: Liquid Colour: Dark Yellow Odor: Detergent ScentOdor Threshold: Not Applicable pH: 10 to 14 Freezing Point: Not AvailableInitial Boiling Point/Boiling Range: Not available Flash Point: Not AvailableEvaporation Rate: Not Available Flammability (solid; gas): Not AvailableLower Flammable/Explosive Limit: Not Available Vapour Pressure: Not AvailableUpper Flammable/Explosive Limit: Not Available Vapour Density: Not AvailableRelative Density: Not Available Solubility: Completely SolublePartition Coefficient – n-octanol/water: Not Available Viscosity: Not AvailableAuto-ignition Temperature: Not Available Decomposition Temperature: Not Available10. STABILITY AND REACTIVITYReactivity: Not availableChemical Stability: StablePossibility of Hazardous Reactions: None under normal processingConditions to Avoid: Water, moisture or humidity, generation of mists and dust.Incompatible Materials:Highly reactive. Reacts violently with organic acids (e.g. acetic acid), inorganic acids (e.g. hydrofluoric acid), oxidizing agents (e.g. peroxides).Hazardous Decomposition Products: Oxides of sodium11. TOXICOLOGICAL INFORMATIONInformation on the Likely Routes of Exposure: Skin contact, Eye contact.∙Inhalation: Not expected to be an inhalation hazard unless it becomes an airborne dust or mist. May cause irritation of the nose and throat.∙Skin Contact: Not expected to cause irritation.∙Eye Contact: May cause mild irritation.∙Ingestion: May cause stomach upset. Symptoms may include nausea, vomiting, stomach cramps and diarrhea. Can cause death.∙Effects of Long-Term (Chronic) Exposure: Not Available.∙Carcinogenicity: Not known to cause cancer.International Agency for Research on Cancer (IARC): Not specifically designated.American Conference for Governmental Industrial Hygienists (ACGIH): Not specifically designated.∙Teratogenicity / Embryotoxicity: Not known to harm the unborn child.∙Reproductive Toxicity: Not known to be a reproductive hazard.∙Mutagenicity: Not known to be a mutagen.12. ECOLOGICAL INFORMATIONEcotoxicity: Not available Persistence and Degradability: Expected to be biodegradable.Bioaccumulative Potential: Not Available Mobility in Soil: Not AvailableOther Adverse Effects: No adverse environmental effects are expected from this product.13. DISPOSAL CONSIDERATIONSWaste Disposal Methods: Disposal of all wastes must be done in compliance with federal, provincial and local regulations. Liquid residues must be properly neutralized to pH 6 – 9 then may be disposed off in waste water treatment facilities which allow the discharge of neutral salt solutions.Contaminated Packaging: Empty containers should be recycled or disposed off through an approved waste management facility.14. TRANSPORT INFORMATIONUN Number: Not Applicable UN Proper Shipping Name: CLEANING COMPOUND Transport Hazard Class: Not Hazardous Packing Group: II Environmental Hazards: Not Available Transport in Bulk: Not AvailableSpecial Precautions:15. REGULATORY INFORMATIONCanadian DSL Inventory Status: All components of this product are either on the Domestic Substances List (DSL), the Non-Domestic Substances List (NDSL) or exempt.16. OTHER INFORMATIONPrepared by: JAIME CORPUZAaladin Superior Cleaning Systems, Ltd.71 Don Valley ParkwayPO Box 62052 Transcona RPOWinnipeg, MB R2C 5G2CanadaDate Prepared: 25 June 2018General Disclaimer: The information provided on this SDS is correct to the best of our knowledge, information and belief at the date of its publication. The information provided is for the purpose only as a guide for safe handling, use, processing,storage, disposal and release. It is not to be considered as a warranty or quality specification.To the best of our knowledge, the information contained herein is accurate. However, neither the supplier nor anyof its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information containedherein. Final determination of suitability of any material is the sole responsibility of the user. All materials maypresent unknown hazards and should be used with caution. Although certain hazards are described herein, wecannot guarantee that these are the only hazards that exist.Aaladin Superior Cleaning Systems expressly disclaims all expressed or implied warranties of merchantability andfitness for a particular purpose with respect to the product provided.。

一种喷淋与浸泡通用的工业清洗剂申请公布号：CN112410135A申请公布日：2021.02.26申请号：2020114542792申请日：2020.12.10申请人：深圳市恒纬祥科技有限公司发明人：郭光明本发明提供一种喷淋与浸泡通用的工业清洗剂。

本发明属于清洗技术领域，涉及一种喷淋与浸泡通用的工业清洗剂。

该清洗剂包括如下质量分数的组分：分散剂1～10、螯合剂0.3～2、碱0.5～4、缓蚀剂0.1～30、表面活性剂5～15、防腐剂0.2～0.5、溶剂1～5。

相对于现有技术，首先，本清洗剂采用具有乳化、润湿、渗透等多种不同作用，以及具有不同泡沫能力的表面活性剂进行组合使用，使清洗剂具有优异的清洗力，且能够减少清洗剂中泡沫的产生，清洗剂既可以在喷淋中使用，也可以在浸泡中使用；其次，清洗剂中加入缓蚀剂能够防止清洗剂对基材造成腐蚀；最后，本清洗剂安全、环保，对人体不会造成损伤。

LX型工业设备用清洗剂申请公布号：CN112410137A申请公布日：2021.02.26申请号：2020113651190申请日：2020.11.27申请人：辽宁蓝欣环保科技有限公司发明人：崔岩本发明公开了LX型工业设备用清洗剂，包括以下质量组分的原料：包括以下质量组分的原料：水80～100份、助溶剂5～10份、有机溶剂5～10份、抗氧化剂5～10份、表面活性剂3～8份、磺化煤3～8份、十八酸钠2～4份、消泡剂2～4份、研磨剂5～10份、分散剂2～4份；换热设备的介质是水，水中含有钙镁离子，温度越高，结垢越重。

本发明是由有机溶剂、表面活性剂、缓蚀剂、渗透剂及研磨剂等多种药剂复配而成的液体，产品可去除多种水垢，无毒、无色、使用安全，提高热效率，并且本发明中通过加入防锈剂和表面活性剂使得清洗剂使用后换热器设备表面形成一层钝化保护膜，并去除表面锈迹，并且清洁剂中碱性和酸性均为弱性，且中和后不会对设备造成腐蚀效果，操作安全、产品无色无味。