H11L1 and H11L2
- 格式：pdf
- 大小：278.42 KB
- 文档页数：6
STYLE 5: PIN 1. ANODE 2. CATHODE 3. NC 4. OUTPUT 5. GROUND 6. VCC
J 6 PL 0.13 (0.005) M T B M A M
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL.
REV 1 ©MMoottoorroolal,aInOc.p1t9o9e5lectronics Device Data
Order this document by H11L1/D
H11L1*
[IF(on) = 1.6 mA Max]
H11L2
[IF(on) = 10 mA Max] *Motorola Preferred Device
ICC(on)
—
VOL
—
Threshold Current, ON (RL = 270 Ω, VCC = 5 V)
H11L1 H11L2
IF(on)
—
—
Threshold Current, OFF (RL = 270 Ω, VCC = 5 V)
H11L1 H11L2
IF(off)
0.3
0.3
Hysteresis Ratio (RL = 270 Ω, VCC = 5 V)
Maximum Operating Temperature(2) Storage Temperature Range(2)
TA
– 40 to + 85
°C
Tstg – 55 to +150
°C
Soldering Temperature (10 s)
TL
260
°C
Isolation Surge Voltage (Pk ac Voltage, 60 Hz, 1 Second Duration)(1)
VISO
7500
Vac(pk)
1. Isolation surge voltage is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc.
Derate above 25°C
Vo VCC
IO PD
0 –16 3 –16
50 150 1.76
Volts Volts
mA
mW mW/°C
TOTAL DEVICE
Total Device Dissipation @ TA = 25°C Derate above 25°C
PD
250
mW
2.94
mW/°C
VOL, OUTPUT VOLTAGE, LOW (VOLTS)
Motorola Optoelectronics Device Data
3
H11L1 H11L2
PACKAGE DIMENSIONS
–A–
6
4
–B–
1
3
F 4 PL
N
C
L
–T–
SEATING PLANE
E 6 PL
K
G M
D 6 PL 0.13 (0.005) M T A M B M
C
—
OUTPUT DETECTOR
Operating Voltage Supply Current (IF = 0, VCC = 5 V)
VCC
3
ICC(off)
—
Output Current, High (IF = 0, VCC = Vo = 15 V)
IOH
—
COUPLED
Supply Current (IF = IF(on), VCC = 5 V) Output Voltage, Low (RL = 270 Ω, VCC = 5 V, IF = IF(on))
ton
—
tf
—
toff
—
tr
—
1. Always design to the specified minimum/maximum electrical limits (where applicable). 2. For this test, IRED Pins 1 and 2 are common and Output Gate Pins 4, 5, 6 are common. 3. RL value effect on switching time is negligible.
• Guaranteed Switching Times — ton, toff < 4 µs • Built–In On/Off Threshold Hysteresis • High Data Rate, 1 MHz Typical (NRZ) • Wide Supply Voltage Capability • Microprocessor Compatible Drive • To order devices that are tested and marked per VDE 0884 requirements, the
IC, SUPPLY CURRENT (mA)
TA = 0°C
6
25°C
70°C
4
IF = 5 mA
0°C
25°C
70°C 2
0
IF = 0 mA
0
2
4
6
8
10 12 14 16
VCC, SUPPLY VOLTAGE (VOLTS)
Figure 6. Supply Current versus Supply Voltage
Rating
Symbol
Value
Unit
INPUT LED
Reverse Voltage
Forward Current — Continuous Forward Current — Peak Pulse Width = 300 µs, 2% Duty Cycle
VR
6
Volts
IF
60
mA
1.2
Amp
STYLE 5 PLASTIC
61
STANDARD THRU HOLE CASE 730A–04
SCHEMATIC
1
6
2
5
3
4
PIN 1. ANODE 2. CATHODE 3. NC 4. OPEN COLLECTOR OUTPUT 5. GND 6. VCC
1
H11L1 H11L2
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)(1)
suffix ”V” must be included at end of part number. VDE 0884 is a test option. Applications
• Interfacing Computer Terminals to Peripheral Equipment • Digital Control of Power Supplies • Line Receiver — Eliminates Noise • Digital Control of Motors and Other Servo Machine Applications • Logic to Logic Isolator • Logic Level Shifter — Couples TTL to CMOS MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
IF 1
2
ICC 5V
6
RL 270 Ω
4 VO (OPEN COLLECTOR OUTPUT)
5
IF (on)
toff ton Vo
tf
tr
Figure 1. Switching Test Circuit
2
Motorola Optoelectronics Device Data
IF, THRESHOLD CURRENT (NORMALIZED)
IF(off)
0.5
IF(on)
Isolation Voltage(2) 60 Hz, AC Peak, 1 second, TA = 25°C
VISO
7500
Turn–On Time Fall Time Turn–Off Time Rise Time
RL = 270 Ω(3) VCC = 5 V, IF = IF(on) TA = 25°C
0
0.75 1
2
IF, INPUT CURRENT (mA)
Figure 2. Transfer Characteristics for H11L1
H11L1 H11L2
1.6
1.4 TURN ON THRESHOLD
