思科路由器交换机命令要全
- 格式:doc
- 大小:2.49 MB
- 文档页数:4
思科交换机常用命令大全1.1 用户模式与特权模式用户模式:可以使用一些基本的查询命令特权模式:可以对交换机进行相关的配置进入特权模式命令:Switch>enable退出特权模式命令:Switch#exit启用命令查询:?时间设置:Switch#clock set 时间(自选参数,参数必须符合交换机要求)显示信息命令:Switch#show 可选参数注意:可以用TAB键补齐命令,自选参数为用户自定义参数,可选参数为交换机设定参数查看交换机配置: Switch#show running-config保存交换机配置:Switch#copy running-config startup-configSwitch#wr查看端口信息:Switch#show interface查看MAC地址表:Switch#show mac-address-table查看交换机CPU的状态信息:Switch#show processes1.2 全局配置模式进入全局配置模式:Switch#configure terminal主机名修改:Switch(config)#hostname 主机名(自选参数)特权模式进入密码: Switch(config)#enable secret 密码(自选参数)取消特权模式密码:Switch(config)#no enable secret取消主机名设置: Switch(config)#no hostname退出配置模式: Switch(config)#exit需要特别注意的是在配置模式中无法使用show命令,如果要使用的话show前必须加do和空格,例如:do show *指定根交换机命令:Switch(config)#spanning-tree vlan 自选参数(VLAN号) root primary例如: Switch(config)#spanning-tree vlan 1 root primary需要注意的是:设置根交换机是基于VLAN的关闭生成树协议命令:Switch(config)#no spanning-tree vlan 自选参数(VLAN号)例如: Switch(config)#no spanning-tree vlan 11.3 接口配置模式进入接口配置模式:Switch(config)#interface 端口名称(可选参数)启用端口:Switch(config-if)#no shutdown停用端口:Switch(config-if)#shutdown进入同种类型多端口配置:Switch(config)# interface range fastethernet 0/1-5进入不同类型多端口配置:Switch(config)#interface range fastethernet 0/1-5,gigabitethernet 0/1-2退出接口配置模式:Switch(config-if)#exit1.4 二层端口的配置端口速率: Switch(config-if)#speed 可选参数双工模式: Switch(config-if)#duplex 可选参数禁用链路协商:Switch(config-if)#no negotiation auto启用链路协商:Switch(config-if)#negotiation auto1.5 VLAN的配置新建VLAN:Switch(config)#vlan 自选参数(VLAN号)Switch(config-vlan)#name自选参数(VLAN名)例如:Switch(config)#vlan 1Switch(config-vlan)#name lab1Switch(config-vlan)#exit删除VLAN: Switch#vlan databaseSwitch(vlan)#no vlan 自选参数(vlan号)例如:Switch#vlan databaseSwitch(vlan)#no vlan 2将一个接口加入VLAN:Switch(config)#interface 可选参数(接口号)Switch(config-if)#switchport mode accessSwitch(config-if)#switchport access vlan 自选参数(VLAN号)Switch(config-if)#no shutdownSwitch(config-if)#exit例如:Switch(config)#interface f0/1Switch(config-if)#switchport mode accessSwitch(config-if)#switchport access vlan 1Switch(config-if)#no shutdownSwitch(config-if)#exit将一个接口退出VLAN:Switch(config)#interface 可选参数(接口号)Switch(config-if)#no switchport access vlan 自选参数(VLAN号)例如:Switch(config)#interface f0/1Switch(config-if)#no switchport access vlan 2修改一个接口为端口汇聚模式Switch(config)#interface 可选参数(接口号)Switch(config-if)#switchport mode trunkVLAN的验证命令:Switch#show vlan 显示VLAN列表Switch#show interface switchport 查看具体接口的VLAN成员资格信息1.6 VTP的配置VTP Domain Name(VTP域名)Switch#configure terminalSwitch(config)#vtp domain 自选参数例如: Switch(config)#vtp domain Lab_NetworkVTP mode(VTP模式)Switch(config)#vtp mode 可选参数(Server|Client| Transparent)例如: Switch(config)#vtp mode ServerVTP Pruning(VTP修剪)Switch(config)#vtp pruning注意:有的交换机不支持VTP修剪命令查看VTP的配置命令:Switch#show vtp status显示交换机运行的VTP模式,配置修订号和交换机所属的VTP域Switch#show vtp counters显示VTP消息相关的统计数据1.7 远程登录交换机设置配置管理VLAN:Switch(conf)#interface vlan 1Switch(config-if)#ip address x.x.x.x 255.255.255.0Switch(config-if)#no shutdown注意:IP地址必须与远程连接交换机的PC机地址在同一网段在交换机上指定默认网关:Switch(config)#ip default-gateway x.x.x.x注意:指定的默认网关仅当前交换机有效。
交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname <hostname> ;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令为xxx switch(config)#enable password xxx ;设置特权非密口令为xxx switch(config)#line console 0 ;进控制台口(Rs232)初始化switch(config-line)#line vty 0 4 ;进入虚拟终端virtual tty switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口1加入VLAN 2 switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain <name> ; 设置发vtp域名switch(config)#vtp password <word>switch(config)#vtp mode serverswitch(config)#vtp mode client交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address <IP> <mask> ;添加远程登录IPswitch(config)#ip default-gateway <IP> ;添加默认网关switch#dir flash: ;查看内存交换机显示命令:switch#write ;写入保存switch#show vtpswitch#show run ;查看当前配置信息switch#show vlan ;看VLAN。
思科公司路由器命令大全详细解释switch> 用户模式1:进入特权模式enableswitch> enableswitch#2:进入全局配置模式configure terminalswitch> enableswitch#c onfigure terminalswitch(conf)#3:交换机命名hostname aptech2950 以aptech2950为例switch> enableswitch#c onfigure terminalswitch(conf)#hostname aptch-2950aptech2950(conf)#4:配置使能口令enable password cisco 以cisco为例switch> enableswitch#c onfigure terminalswitch(conf)#hostname aptch2950aptech2950(conf)# enable password cisco5:配置使能密码enable secret ciscolab 以cicsolab为例switch> enableswitch#c onfigure terminalswitch(conf)#hostname aptch2950aptech2950(conf)# enable secret ciscolab6:设置虚拟局域网vlan 1 interface vlan 1switch> enableswitch#c onfigure terminalswitch(conf)#hostname aptch2950aptech2950(conf)# interface vlan 1aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip和子网掩码aptech2950(conf-if)#no shut 是配置处于运行中aptech2950(conf-if)#exitaptech2950(conf)#ip default-gateway 192.168.254 设置网关地址7:进入交换机某一端口interface fastehernet 0/17 以17端口为例switch> enableswitch#c onfigure terminalswitch(conf)#hostname aptch2950aptech2950(conf)# interface fastehernet 0/17aptech2950(conf-if)#8:查看命令showswitch> enableswitch# show version 察看系统中的所有版本信息show interface vlan 1 查看交换机有关ip 协议的配置信息show running-configure 查看交换机当前起作用的配置信息show interface fastethernet 0/1 察看交换机1接口具体配置和统计信息show mac-address-table 查看mac地址表show mac-address-table aging-time 查看mac地址表自动老化时间9:交换机恢复出厂默认恢复命令switch> enableswitch# erase startup-configureswitch# reload10:双工模式设置switch> enableswitch#c onfigure terminalswitch2950(conf)#hostname aptch-2950aptech2950(conf)# interface fastehernet 0/17 以17端口为例aptech2950(conf-if)#duplex full/half/auto 有full , half, auto 三个可选项11:cdp相关命令switch> enableswitch# show cdp 查看设备的cdp全局配置信息show cdp interface fastethernet 0/17 查看17端口的cdp配置信息show cdp traffic 查看有关cdp包的统计信息show cdp nerghbors 列出与设备相连的cisco设备12:csico2950的密码恢复拔下交换机电源线。
交换机路由器命令合集(思科)1.基础Switch> !⼀般⽤户模式Switch# !特权模式Switch(config)# !全局配置模式Switch(config)#honstname S1 !更改交换机设备[h S1]S1(config)#exit !从当前模式返回到上⼀级模式S1(config)#end !从任何模式直接退回到特权模式S1#show running-config !查看交换机配置S1(config)#do show running-config !查看交换机配置S1#save !保存配置⽂件,以便设备关闭电源重启后能继续使⽤2.配置a.对控制端⼝(Console)添加密码保护S1#configure terminal [conf t]S1(config)#line consloe 0 !进⼊控制⼝⾏配置模式S1(config-line)#password 123456 !设置密码为123456S1(config-line)#login !开始密码检查S1(config-line)#endS1#b.在全局配置模式下设置特权明⽂密码和密⽂密码(同时设置密⽂密码优先)S1(config)#enable password 123 !设置特权铭⽂密码为123S1(config)#enable secret 456 !设置特权密码为456c.使⽤Telnet远程登陆⽅式登陆交换机进⾏配置i。
设置交换机管理ip地址交换机出⼚时都有⼀个默认的虚拟端⼝VLAN1⽤于管理S1(config)#interface Vlan 1 !进⼊交换机默认的虚拟端⼝1,进⼊配置模式S1(config-if)#ip address 192.168.1.1 255.255.255.0 !配置虚拟端⼝的ip和⼦⽹掩码S1(config-if)#no shutdown !通常对端⼝作相关配置后都要开启端⼝S1(config-if)#exitS1(config)#ii。
捍卫祖国的尊严和领土完整是每一个中国人的神圣使命钓鱼岛自古以来就是中国的固有领土,作为每一个中国人,在中国领土受到极端挑战的时刻,心情是沉痛的、复杂的、愤怒的!在大是大非面前,我们该何去何从,如何决择,体现的是一个央央大国的智慧、尊严、精干和力量!一、从“撞船事件”看清敌人野心从表面看,“撞船事件”到关押中国船长是一个个体事件,是“莫须有”的侵害日本利益的行径,因为在日本人、美国人眼中,钓鱼岛是他们的领土,况且他们还建有标牌、有军队巡逻驻守;从深层看,是关系到向世界宣称争议领土的确权问题,上升到了国家层面。
就日本而言,他是要通过这次事件,进一步巩固对钓鱼岛的“所有权”,并试探有杂音的人的底线,从而搅乱中国的良好发展局面,可误用心良苦,手段毒辣。
就中国而言,是坏事,也是好事。
自古以来,钓鱼岛是中国领土的一部分,只是由于历史原因,对其丢失了管辖,以致让聪明的野心人占了先机,以致让自己的领土自己却没有主动权,甚至还要受人家管制,这是可悲的、可恨的!但我坚信,这只是一个过程,一个历史犯下错误的过程,作为中国的炎黄子孙,有权利、有义务、更有信心保家卫国!为此,我们一定要审时度势,变被动为主动,抓住有利时机,重新收回并牢牢掌握对自家领土的所有权、管理权。
二、从被动变主动、从“失败”变完胜的策略目前,中国船长还被日本拘押,中国从民间到部长、甚至到我们的总理都公开正式向日本提出过严正交涉,但却都于事无补,而且日方依旧是铁板一块,态度极其坚决。
这时,考验的是我们每一个华夏儿女的智慧、谋略和综合力量。
“打蛇要打在七寸上”,要看清事情的本质,我们的目的是什么?绝不仅仅是要他“立即放回中国船长”这么简单,假如今天或明天,日本放回了中国船长,我们是不是就平安无事,就不和他计较,还和他回到从前,他还照样履行对钓鱼岛的管辖,如是这样,我们这一仗就真的失败了,而且败得很惨!我们的最终目的是要抓住这个良机,收回属于我们自己的领土,而且我们是有这个信心和实力的。
思科交换机路由器命令大全思科交换机和路由器命令大全本文档为思科交换机和路由器命令的最新最全范本,供参考使用。
以下是详细的命令列表,包括每个命令的说明和用法。
一、接口配置命令1、ip address:设置接口的IP地质示例:ip address 192.168.1.1 255.255.255:02、no shutdown:启用接口示例:no shutdown3、duplex:设置接口的双工模式示例:duplex auto4、speed:设置接口的速度示例:speed 1005、exit:退出接口配置模式示例:exit二、VLAN命令1、vlan database:进入VLAN数据库模式示例:vlan database2、vlan id name:创建VLAN并设置名称示例:vlan 10 name VLAN-103、vlan id:删除VLAN示例:no vlan 104、show vlan:显示VLAN信息示例:show vlan5、exit:退出VLAN数据库模式示例:exit三、路由命令1、ip route:设置静态路由示例:ip route 192.168.2:0 255.255.255:0 192.168.1.22、router rip:启用RIP路由协议示例:router rip3、network:将网络添加到RIP路由表中示例:network 10:0:0:04、redistribute:将静态路由或其他路由协议添加到RIP路由表中示例:redistribute static5、exit:退出路由配置模式示例:exit四、ACL命令1、access-list:创建标准或扩展ACL示例:access-list 10 permit 192.168.1:0 0:0:0.2552、ip access-group:应用ACL到接口示例:ip access-group 10 in3、show access-lists:显示ACL信息示例:show access-lists4、exit:退出ACL配置模式示例:exit五、SNMP命令1、snmp-server community:设置SNMP团体字符串示例:snmp-server community public RO2、snmp-server enable traps:启用SNMP陷阱示例:snmp-server enable traps3、snmp-server host:配置SNMP陷阱接收主机示例:snmp-server host 192.168.1.1004、exit:退出SNMP配置模式示例:exit六、SSH命令1、ip ssh version:设置SSH协议版本示例:ip ssh version 22、crypto key generate rsa:RSA密钥对示例:crypto key generate rsa3、username:创建新的本地用户示例:username admin privilege 15 password password1234、exit:退出SSH配置模式示例:exit七、其他命令1、show running-config:显示当前配置示例:show running-config2、copy running-config startup-config:将当前配置保存到启动配置中示例:copy running-config startup-config3、reload:重新启动设备示例:reload4、exit:退出CLI命令行模式示例:exit本文档涉及附件:1、无附件本文所涉及的法律名词及注释:1、ACL(Access Control List):访问控制列表,用于控制网络流量的进出。
思科交换机命令大全+CiscoIOS基本命令思科交换机命令大全(一)序号/类别基于ios的交换机命令基于CLI的交换机命令1.设置主机名/系统名switch(config)# hostname "hostname" switch(enable) setsystem name name-string2.设置登录口令switch(config)# enable password level 1 password switch(enable) set passwordswitch(enable) set enalbepass3.设置远程访问switch(config)# inte***ce vlan 1switch(config-if)# ip address ip-address netmaskswitch(config-if)# ip default-gateway ip-address switch(enable) set inte***ce sc0 ip-address netmask broadcast-addressswitch(enable) set inte***ce sc0 vlanswitch(enable) set ip route default gateway4.启用和浏览CDP信息switch(config-if)# cdp enableswitch(config-if)# no cdp enable switch(enable) set cdp {enable|disable}module/port5.查看Cisco邻接设备的CDP通告switch# show cdp inte***ce [type modle/port] switch# show cdp neighbors [type module/port] [detail] switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail] 6.端口描述switch(config-if)#description escription-string switch(enable)set port name module/number description-string 7.设置端口速度switch(config-if)# speed{10|100|auto} switch(enable) set portspeed moudle/number {10|100|auto}switch(enable) set port speed moudle/number {4|16|auto} 8.设置以太网的链路模式switch(config-if)# duplex {auto|full|half} switch(enable) set port duplex module/number {full|half9.配置静态VLAN switch# vlan databaseswitch(vlan)# vlan vlan-num name vlaswitch(vlan)# exitswitch# configure teriminalswitch(config)#inte***ce inte***ce module/numberswitch(config-if)# switchport mode accessswitch(config-if)# switchport access vlan vlan-numswitch(config-if)# end switch(enable) set vlan vlan-num [name name]switch(enable) set vlan vlan-num mod-num/port-list10.配置VLAN中继线switch(config)# inte***ce inte***ce mod/portswitch(config-if)# switchport mode trunkswitch(config-if)#switchport trunk encapsulation {isl|dotlq} switch(config-if)# switchport trunk allowed vlan remove vlan-listswitch(config-if)# switchport trunk allowed vlan add vlan-list switch(enable)settrunk module/port [on|off|desirable|auto|nonegotiate]Vlan-range [isl|dotlq|dotl0|lane|negotiate]11.配置VTP管理域switch# vlan databaseswitch(vlan)# vtp domain domain-name switch(enable) set vtp [domain domain-name]12.配置VTP 模式switch# vlan databaseswitch(vlan)# vtp domain domain-nameswitch(vlan)# vtp {sever|cilent|transparent}switch(vlan)# vtp password password switch(enable) set vtp [domaindomain-name] [mode{ sever|cilent|transparent }][password password]13.配置VTP版本switch# vlan databaseswitch(vlan)# vtp v2-mode switch(enable) set vtp v2 enable 14.启动VTP剪裁switch# vlan databaseswitch(vlan)# vtp pruning switch(enable) set vtp pruning enable15.配置以太信道switch(config-if)# port group group-number [distribution {source|destination}] switch(enable) set port channel moudle/port-rangemode{on|off|desirable|auto}16.调整根路径成本switch(config-if)#spanning-tree [vlan vlan-list] cost cost switch(enable)set spantree portcost moudle/port costswitch(enable)set spantree portvlancost moudle/port [cost cost][vlan-list] 17.调整端口ID switch(config-if)#spanning-tree[vlan vlan-list]port-priorityport-priority switch(enable)set spantree portpri {mldule/port}priorityswitch(enable)set spantree portvlanpri {module/port}priority [vlans]18.修改STP时钟switch(config)# spanning-tree [vlan vlan-list] hello-time secondsswitch(config)#spanning-tree [vlan vlan-list] forward-time secondsswitch(config)#spanning-tree [vlan vlan-list] max-age seconds switch(enable) set spantree hello interval[vlan]switch(enable) set spantree fwddelay delay [vlan]switch(enable) set spantree maxage agingtiame[vlan]19.启用或禁用Port Fast 特征switch(config-if)#spanning-tree portfastswitch(enable)set spantree portfast {module/port}{enable|disable}20.启用或禁用UplinkFast 特征switch(config)#spanning-tree uplinkfast[max-update-rate pkts-per-second] switch(enable)set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令:switch(config)# cluster enable cluster-name21. 为了从一条中继链路上删除VLAN,可使用下列命令:switch(enable) clear trunk module/port vlan-range22. 用show vtp domain 显示管理域的VTP参数.23. 用show vtp statistics显示管理域的VTP参数.24. 在Catalyst交换机上定义TrBRF的命令如下:switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp{ieee|ibm}]25. 在Catalyst交换机上定义TrCRF的命令如下:switch (enable) set vlan vlan-num [name name] type trcrf {ringhex-ring-num|decring decimal-ring-num} parent vlan-num26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:switch(enable) set vlan vlan-num mod-num/port-num27. 命令show spantree显示一个交换机端口的STP状态.28. 配置一个ELAN的LES和BUS,可以使用下列命令: ATM (config)# inte***ce atm number.subint multiointATM(config-subif)# lane serber-bus ethernet elan-name29. 配置LECS: ATM(config)# lane database database-nameATM(lane-config-databade)# name elan1-name server-atm-addressles1-nsap-addressATM(lane-config-databade)# name elan2-name server-atm-addressles2-nsap-addressATM(lane-config-databade)# name ...30. 创建完数据库后,必须在主接口上启动LECS.命令如下: ATM(config)#inte***ce atm numberATM(config-if)# lane config database database-nameATM(config-if)# lane config auto-config-atm-address31. 将每个LEC配置到一个不同的ATM子接口上.命令如下: ATM(config)#inte***ce atm number.subint multipointATM(config)# lane client ethernet vlan-num elan-num32. 用show lane server 显示LES的状态.33. 用show lane bus显示bus的状态.34. 用show lane database显示LECS数据库可内容.35. 用show lane client显示LEC的状态.36. 用show module显示已安装的模块列表.--------------------------------------------------------------------------------37. 用物理接口建立与VLAN的连接: router# configure terminalrouter(config)# inte***ce media module/portrouter(config-if)# description description-stringrouter(config-if)# ip address ip-addr subnet-maskrouter(config-if)# no shutdown38. 用中继链路来建立与VLAN的连接: router(config)# inte***cemodule/port.subinte***cerouter(config-ig)# encapsulation[isl|dotlq] vlan-numberrouter(config-if)# ip address ip-address subnet-mask39. 用LANE 来建立与VLAN的连接: router(config)# inte***ce atm module/port router(config-if)# no ip addressrouter(config-if)# atm pvc 1 0 5 qsaalrouter(config-if)# atm pvc 2 0 16 ilnirouter(config-if)# inte***ce atm module/port.subinte***ce multipointrouter(config-if)# ip address ip-address subnet-maskrouter(config-if)# lane client ethernet elan-numrouter(config-if)# inte***ce atm module/port.subinte***ce multipointrouter(config-if)# ip address ip-address subnet-namerouter(config-if)# lane client ethernet elan-namerouter(config-if)# ...40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:router(config)# ip routingrouter(config)# router ip-routing-protocolrouter(config-router)# network ip-network-numberrouter(config-router)# network ip-network-number41. 配置默认路由: switch(enable) set ip route default gateway42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:router(config)# inte***ce inte***ce numberrouter(config-if)# mls rp vlan-id vlan-id-num43. 在路由处理器启用MLSP: router(config)# mls rp ip44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP 域中:router(config)# inte***ce inte***ce numberrouter(config-if)# mls rp vtp-domain domain-name45. 查看指定的VTP域的信息: router# show mls rp vtp-domain vtp domain name46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:router(config-if)#mls rp management-inte***ce47. 要检验MLS-RP的配置情况:router# show mls rp48. 检验特定接口上的MLS配置:router# show mls rp inte***ce inte***ce number49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:set mls flow [destination|destination-source|full]50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:router(config)# mls rp ip input-acl51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:switch(enable) set mls enable52. 若想改变老化时间的值,可在特权模式下输入以下命令:switch(enable) set mls agingtime agingtime53. 设置快速老化:switch(enable) set mls agingtime fast fastagingtimepkt_threshold54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:switch(enable) show mls include55. 显示MLS高速缓存记录:switch(enable) show mls entry56. 用命令show in arp显示ARP高速缓存区的内容。
交换路由常用命令一、基础配置1、修改主机名配置:S(config)#hostname SWITCHA2、enable口令:Switch(config)#enable password1233、TELNET:只需密码的telnet需用户名和密码的telnetS(config)#line vty04S(config)#username S2password123S(config-line)#password123S(config)#line vty04S(config-line)#login//启用登陆时口令检查S(config-line)#login local//启用登陆本地验证只允许pc所在的网段对交换路由进行远程登陆:S(config)#access-list99permit192.168.1.00.0.0.255S(config)#line vty04S(config-line)#access-class99inS(config-line)#password123S(config-line)#login4、console配置:S(config)#line console0S(config-line)#password123S(config-line)#login5、显示当前配置:switch#show run6、保存当前配置:switch#write7、进入全局配置模式:switch#conf t8、进入接口配置模式:S(config)#interface f0/1二、二层接入交换机常见配置1、创建vlan10及命名:S(config)#vlan10S(config-vlan)#name caiwubu2、多个端口划分入vlan:vlan:S(config)#int range fa0/1-5S(config-if)#sw access vlan103、接口trunk模式配置:S(config)#inter f0/0S(config-if)#sw mode trunk4、二层交换机管理ip配置:S2(config)#interface vlan100//进入vlan100接口S2(config-if)#ip address192.168.10.1255.255.255.0//为vlan100接口上设置管理ip S2(config)#ip default-gateway192.168.10.2545、生成树配置:S(config)#spanning-tree mode rapid-pvst//配置快速生成树S(config)#spanning-tree vlan10,20priority0//配置根网桥S(config)#spanning-tree vlan10,20,30priority4096//配置备份根网桥6、端口双工、带宽设置:S(config)#int F0/2S(config-if)#duplex fullS(config-if)#speed100三、三层交换机常见配置1、三层交换机开启路由功能:S(config)#ip routing//开启后可实现vlan间相互通信2、三层交换机接口配置成路由口:S(config-if)#no swtichport//在接口模式下配置,可配置ip地址3、三层交换机创建SVI接口(SVI接口常作为vlan的网关):S(config)#interface vlan104、三层交换机接口改trunk模式:Switch(config-if)#switchport trunk encapsulation dot1q//先封装Switch(config-if)#switchport mode trunk//再设置trunk模式5、trunk允许vlan通过:S(config)#inter fa0/23S(config-if)#switchport trunk allowed vlan2,3//trunk口只让vlan2,3通过S(config-if)#switchport trunk allowed vlan all//trunk口允许所有的vlan通过四、路由器常见配置1、ip地址设置:router(config-if)#ip address192.168.1.1255.255.255.0//接口模式下配置2、静态路由配置:router(config)#ip route192.168.1.0255.255.255.010.1.1.1{f0/0}//下一跳地址可替换为出接口3、默认路由配置:router(config)#ip route0.0.0.00.0.0.010.1.1.14、浮动静态路由作为备份路由:R(config)#ip route172.16.20.0255.255.255.010.10.10.4R(config)#ip route172.16.20.0255.255.255.010.10.10.6100//路由开销值100比默认值1大,作为备份路由5、路由可达,有去有回。
思科路由器命令大全思科路由器命令大全1.基本设置命令1.1 主机名配置●hostname [主机名]:设置路由器的主机名。
1.2 用户名和密码配置●enable password [密码]:设置特权模式的密码。
●enable secret [密码]:设置加密的特权模式密码。
●username [用户名] password [密码]:创建一个本地用户并设置密码。
●line console 0:进入控制台命令行配置模式。
●password [密码]:设置控制台访问密码。
●line vty [行号] [结束行号]:进入虚拟终端配置模式。
●password [密码]:设置虚拟终端访问密码。
1.3 IP 地质配置●interface [接口类型] [接口编号]:进入接口配置模式。
●ip address [IP 地质] [子网掩码]:设置接口的IP 地质和子网掩码。
●no shutdown:启用接口。
1.4 默认网关配置●ip default-gateway [默认网关地质]:设置默认网关。
2.路由配置命令2.1 静态路由配置●ip route [目标网络] [目标子网掩码] [下一跳地质]:配置静态路由。
2.2 动态路由配置●router rip:进入 RIP 路由配置模式。
●network [网络地质]:启动 RIP 并指定要进行路由的网络地质。
●router ospf [进程号]:进入 OSPF 路由配置模式。
●network [IP 地质] [反掩码] area [区域号]:配置 OSPF。
3.状态和监控命令3.1 接口状态命令●show ip interface brief:显示路由器接口的 IP 地质和状态。
●show interfaces [接口类型] [接口编号]:显示指定接口的详细信息。
●show interfaces status:显示接口的状态和统计信息。
3.2 路由表命令●show ip route:显示路由表信息。
思科路由器交换机命令要全
捍卫祖国的尊严和领土完整是每一个中国人的神圣使命
钓鱼岛自古以来就是中国的固有领土,作为每一个中国人,在中国领土受到极端挑战的时刻,心情是沉痛的、复杂的、愤怒的!在大是大非面前,我们该何去何从,如何决择,体现的是一个央央大国的智慧、尊严、精干和力量!
一、从“撞船事件”看清敌人野心
从表面看,“撞船事件”到关押中国船长是一个个体事件,是“莫须有”的侵害日本利益的行径,因为在日本人、美国人眼中,钓鱼岛是他们的领土,况且他们还建有标牌、有军队巡逻驻守;从深层看,是关系到向世界宣称争议领土的确权问题,上升到了国家层面。
就日本而言,他是要通过这次事件,进一步巩固对钓鱼岛的“所有权”,并试探有杂音的人的底线,从而搅乱中国的良好发展局面,可误用心良苦,手段毒辣。
就中国而言,是坏事,也是好事。
自古以来,钓鱼岛是中国领土的一部分,只是由于历史原因,对其丢失了管辖,以致让聪明的野心人占了先机,以致让自己的领土自己却没有主动权,甚至还要受人家管制,这是可悲的、可恨的!但我坚信,这只是一个过程,一个历史犯下错误的过程,作为中国的炎黄子孙,有权利、有义务、更有信心保家卫国!为此,我们一定要审时度势,变被动为主动,抓住有利时机,重新收回并牢牢掌握对自家领土的所有权、管理权。
准备。
分析敌情,做到成竹在胸。
二是要实弹演习。
宣告天下,在钓鱼岛附近进行实弹演习,越快越好。
三是派军巡逻。
钓鱼岛是中国领土,敌人的聪明,就是善于以假乱真,先下手为强,在那里建标牌、安排军人巡逻。
我们中国为什么就不能那样做,所以,我们也必须派军巡逻,而且这次是最好时机,这是收回我领土的关键一步,如果不这样,一切都是空话,以后恐怕抓中国船长的事件会屡禁不止。
但是我军巡逻,不是与日方就此开打,要看准时机,以不变应万变。
5、坚定信心,该出手时就出手。
中国的发展需要和平,中国的人民爱好和平。
但如果和平和发展要用自己的领土和“孩子”作为牺牲的话,就有背历史、有背先烈。
因此,我们一定要时刻保持我军的优良传统,一秒也不可偏离。
作为国家决策者来说,真的要慎之又慎,虽然我们不希望战争,但是我们不能容忍我们的国家失去尊严,不能容忍我们的国家领土无限度地分裂,哪怕要用我们的生命来换,我们也愿意!请相信,不管国家作出如何决择,我们13亿同胞都并肩作战,生死与共!在解决历史问题上,我们国家需要有一个开创历史的人,带领我们去完成使命!。