FDB说明书Ver

—1 —The G11 provides total of 22 guitar cabinet emulations of all modeling amps.Cabinet Simulations offer the sonic response of each amp’s cabinet when using G11 connected to a real amplifier.In addition, G11 provides 70 pre-loaded high-resolution impulse response (IR data) of the cabinets that were captured by placing the microphone in three different positions. Each cabinet has a recording where the mic was placed 1-inch away (2.5 cm approx.), a recording where the mic was placed 12-inches away (30 cm approx.), and one where the mic was placed in the Room.IR Data offer a full variety of sonic responses when using G11 connected DIRECT OUT to a PA or monitor system.*No. 17 has a 4th IR (MSV_Mix), which is a mix of the recording of the mic at 1-inch and in the room.12-Inches—2 —The G11 provides bass cabinet emulations of 12 classic amp cabinets. In addition, the G11 provides 36 pre-loaded high-resolution impulse response (IRs), three different micpositions for each of the 12 cabinets. IRs offer a full variety of sonic responses when going directly to a PA or monitor system.* Bass cabinets with tweeters use mixes of On Mic and Tweeter IR data.Copying or reprinting this manual in part or in whole without permission is prohibited.Product names, registered trademarks and company names in this document are the property of their respective companies.All trademarks and registered trademarks in this document are for identification purposes only and are not intended to infringe on the copyrights of their respective owners.©2021 ZOOM CORPORATION Z2I-4521-01[ Bass cabinets ][ Bass cabinets with tweeters ]On Mic 2 ( D57 )RoomTweeter Mix : On Mic ( D20 ) + Tweeter ( D57 )。

12/30/1999OPERATOR’S MANUALADDENDUMModel:GP1650/1850 Series Subject:New FISHING MODE andFeature EnhancementsThis Furuno GP1650/1850 Series Plotter has a newly developed software revision that includes many exciting new features. This addendum is a supplement to your Operator’s Manual. It describes these new features and explains how to utilize them.TABLE OF CONTENTSA. Explanation of New Features (2)B. Operator’s Manual Information (3)C. Software Revision Check (3)D. New Fishing Modes and Mark Function (5)E. New Memory Card Storage Function (8)F. Navionics “Nav-Chart” Cartography “OFFSET” Capability (11)G. RTCM DGPS Data Output(1650/1850 “D”/”DF” ONLY) (12)H. New “Wide-Screen” E/S Mode(1650/1850 “F”/”DF” ONLY)..13A.Explanation of New Features:1.New "Fishing Plotter Mode": This feature allows you to place yourGP1650/1850 in either a "Pleasure Mode" or a "Fishing Mode". Inthe "Pleasure Mode", the GP1650/1850 operates the same asprevious software revisions.In the new Fishing Mode, you can place Marks and Line Points (UpTo 5000) in internal memory. The mode also allows you to changeTrack Colors, Start/Stop Own Ship Tracking, and Edit Mark Entrieseasily from a newly added Softkey Menu. In “Pleasure Mode”, thisnew Softkey Menu is not displayed.2. New "Memory Card Storage" Capability: It is now possible tostore Marks/Lines, Waypoints/Routes, Tracks, and ConfigurationInformation (Menu Settings) of the GP1650/1850 Series onto amemory card. The entire memory contents of a GP1650/1850 can bestored into a single memory card for storage or cloning yourGP1650/1850. This provision allows Unlimited Data Storage for theGP1650/1850 Series. Uploading/Downloading Waypointinformation via the RS232 PC Interface has remained unchanged.The part number for the RAM Storage Card is 000-140-483. It isavailable from any authorized Furuno Dealer.3.RTCM DGPS Data Output: It is now possible to send RTCM 104,Differential Correction Data, to other Differential-Ready GPSProducts on your vessel. This feature requires a "D" or ”DF” version.4.Navionics Cartography "OFFSET" Capability: This newsoftware allows operators to OFFSET Navionics Charts. Previoussoftware versions did not have this capability.5."Wide-Screen" Echo Sounder Mode: When operating in the “SplitScreen” mode (Plotter and Sounder display), this function allows theuser to select between the wide (50%) or narrow (25%) sounderscreen. This feature requires a “F” or “DF” version.B.Operator’s Manual – The Operator’s Manual included with yourGP1650/1850 is not updated at this time. We will offer revisedOperator’s Manuals late in the first quarter of 2000.Please call your authorized Furuno Dealer for further information.This software revision does not effect the Installation Manual included with your GP1650/1850.C.Software Revision Check (For Confirmation Only) - TheSoftware Revision of your GP1650/1850 can be found by using the “Self Test” procedure on page 4.The “Memory I/O” test will display the software revision number in the upper left corner of the display.The last two digits of the number indicate which software version is currently installed.If your revision number is lower than the ones listed below, a simplesoftware upgrade for any GP1650/1850 is all that is necessary to takeadvantage of the new features available.Call your local Furuno Dealership for more information.-GP1650/GP1650D Software Version 145-1801-013 and higher -GP1650F/GP1650DF Software Version 145-1802-011 and higher -GP1850D Software Version 145-1826-006 and higher -GP1850DF Software Version 145-1827-006 and higherD iagnostic TestsMemory, I/O port testThis test conducts a general check of the dis-play unit and the antenna unit. The unit dis-plays the results for each device or component checked as OK or NG (No Good).1.Press the [MENU] key to open the mainmenu.2.Press the soft key CONFIGURATION toshow the configuration menu.Figure 12-1 Configuration menu3.Press the soft key SYSTEM MENU toopen the system menu.Figure 12-2 System menu 4.Press the soft key SELF TEST to openthe test menu.Figure 12-3 Test menu5.Press the soft key MEMORY•I/O TESTto start the test. Test results and program nos. are shown as below.NOTE: Special connections are required to check PORT1 and PORT2 otherwise, "--" appears.Figure 12-4 Memory, I/O test results 6.The test runs continuously. To return tothe self test menu, press the soft key RETURN.Note: BEACON RECEIVER results only ap-pear on GP-1650/1850 "D" and "DF" Ver.C hanging Operation ModeOperation mode can be changed between PLEASURE and FISHING. FISHING mode provides mark/line entr ies on the PLOTTER display. Up to 5000 Marks can be entered together with track points. Apportioning between track and mark memory can be changed by menu. Pressing the [HIDE/SHOW] key changes the function of soft keys.Holding tracks, changing track color, select-ing mark colors, and the type of marks/lines can be performed by the soft keys directly.1.Press the [MENU] key and the soft key DISPLAY OPTIONS. The display setup1menu appears.Display setup1 menu2.Press w to select OPERATION MODE.3.Press the soft key EDIT to show the OP-ERATION MODE window.OPERATION MODE window 4.Press v or w to select PLEASURE or FISHING.5.Press the soft key ENTER or the [ENTER]key to finish.In the FISHING mode, pressing the [HIDE/SHOW] key changes the function of soft keys as follows.MARK S1 Entering MarksSelect the Fishing Mode to enable entry of marks on the PLOTTER display. Select the location desired with the cursor, or turn off the cursor to enter the mark at own ship po-sition. Press ing the [HIDE/SHOW] key changes the function of soft keys. Press the soft key MARK ENTRY to enter a new mark. The mark is entered in the shape and color selected from the MARK SHAPE and MARK COLOR selection windows.2 Changing Mark AttributesYou can select the shape s, line types and color s of Marks and L ine s on the TRACK display.1.Press the [HIDE/SHOW] key to show thesoft key MARK EDIT.2.Press the soft key MARK EDIT to showthe MARK/LINE window.MARK SHAPEMARK LINEMARK COLOR YELLOW.MA RK/LINE window3.Press the soft key MARK SHAPE tochange mark shape, the soft key MARKLINE to change mark line, or the soft keyMARK COLOR to change mark color.Mark shapePress the soft key MARK SHAPE to dis-play the MARK SHAPE window. Press vor w to select mark shape desired.MARK SHAPE windowMark linePress the soft key MARK LINE to display the MARK LINE window. Press v or w to select mark line desired.MARK LINE windowMark colorPress the soft key MARK COLOR to dis-play the MARK COLOR window. Press v or w to select mark color desired.MARK COLORv™™™™™™w' REDYELLOWGREENLIGHT BLUEPURPLEBLUEWHITEMARK COLOR window4.Press the soft key ENTER or the [ENTER]key.5.Press the soft key RETURN to finish. Marks/lines entered hereafter are inscribed in the shape, color and line type selected here.3 Changing Mark SizeMark size can be selected from STD (stan-dard) and SMALL.1.Press the [MENU] key to display the mainmenu.2.Press the soft key CHART SETUP OP-TIONS.3.Press the soft key CHART DETAIL toopen the CHART DETAIL menu.CHART DETAIL menu4.Press w to select MARK SIZE.5Press the soft key EDIT.6.Press v or w to select STD (standard) orSMALL.7.Press the [ENTER] key.4 Erasing MarksErasing individual marks/lines1.Operate the cursor pad to place the cur-sor on the mark you want to erase.2.Press the [CLEAR] key. The mark se-lected is erased.Note: To erase a line, place the cursoron the e d ge of the line. The line segment will be erased.Erasing whole marks/linesYou can erase all marks and lines. Be abso-lutely sure you want to erase all marks and lines; erased marks and lines cannot be re-stored.1.Press the [MENU] key followed by the softkeys CHART SETUP OPTIONS andTRACK CONTROL.2.Press the soft key ERASE MARK. Youare asked if you are sure to erase allmarks and lines.3.Press the [ENTER] key to erase, or pressthe [CLEAR] key to escape.5 Displaying Track andMark PointsNumber of track and mark points used ap-pears in the TRACK STATUS window on the TRACK CONTROL display. For further de-tails see TRACK CONTROL WINDOW.SAVING AND LOADING DATA TO/FROM MEMORY CARDSThe following data can be saved to memory card:• Mark/line• Waypoints/routes• Track• Configration (menu settings)1 Formatting Memory CardsBefore you can use a memory card it must be formatted. Note that formatting always erases all saved data on the card!1.Insert the memory card you want to for-mat into the slot.2.Press the [MENU] key followed by the softkeys CONFIGRATION and UPLOAD/ DOWNLOAD DATA.SAVE DATA display3.Press the soft key SAVE DATA TOMEMORY CARD and the soft key FOR-MAT. You are asked if you are ready to format the memory card.4.Press the [ENTER] key to format (or pressthe [CLEAR] key to escape). Now FOR-MATTING MEMORY CARD appears. Do not remove the card while it is being for-matting. When the formatting is com-pleted, FORMAT COMPLETED appears.5.Press the [ENTER] key to finish. Now youcan record data to the memory card.2 Saving Data to MemoryCardThe memory card can save four items of data; track, mark/line, waypoint/route and configu-ration.Saving data1.Insert a formatted memory card into theslot.2.Press the [MENU] key followed by the softkeys CONFIGURATION and UPLOAD/ DOWNLOAD DATA.3.Press the soft key labeled SAVE DATATO MEMORY CARD. The SAVE DATA display appears.4.Press v or w to select item to save.5.Press the soft key EDIT to open theTRACK, MARK/LINE, WAYPOINTS/ ROUTES or CONFIGRATION window.6.Press v to select ON.7.Press the soft key ENTER or the [ENTER]key.8.Repeat from steps 4 to 7 to save otherdata if desired.9.Press the soft key SAVE DATA. The fol-lowing message appears and saving starts. Do not remove the memory card while data is being saved.NOW SAVING DATA TOMEMORY CARD. DO NOTTURN OFF THE POWER UNTILSAVING COMPLETED.SAVE DATA messageWhen saving is completed, COM-PLETE SAVING DATA appears.Error messageMemory card not insertedPress the [ENTER] key to return to the SAVE DATA display.MEMORY CARD NOTINSERTED. INSERT CARDPRESS "ENTER" keyTO CONTINUE.NOT INSERTED message Unformatted memory cardPress the [ENTER] key to return to the SAVE DATA display. And format it refering to the previous page.MEMORY CARD NOTFORMATTEDPRESS "ENTER" keyTO CONTINUE.NOT FORMATTED messageWrong card insertedAppears when a chart card is inserted. Press the [ENTER] key to return to the SAVE DATA display. Replace it with a formatted memory card.WRONG CARD INSERTED.INSERT MEMORY CARD.PRESS "ENTER" keyTO CONTINUE.WRONG CARD messageData overwriteData type to be recorded exists on memory card. (Two or more of same data type can-not be recorded.) Press the [ENTER] key to overwrite same data type on the card, or press the [CLEAR] key to escape.OVERWRITE message3 Loading Data fromMemory CardData (track, marks, waypoints, configuration) can be loaded from a memory card and dis-played on the screen. This feature is useful for observing past data and setting up the equipment for a specific purpose (with “con-figuration”).1.Press the [MENU] key followed by the softkeys CONFIGURATION and UPLOAD/ DOWNLOAD DATA.2.Press the soft key LOAD DATA FROMMEMORY CARD to show the LOAD DATA display.LOAD DATA display3.Press v or w to select item to load.4.Press the soft key EDIT to show theON/OFF selection window.5.Press v to select ON. Press the soft keyENTER or the [ENTER] key. If the memory card does not contain the item selected, the buzzer sounds and ON can-not be selected.6.After you select all items desired, pressthe soft key LOAD DATA to load data. Thefollowing message appears.NOW LOADING DATA FROMMEMORY CARD. DO NOTTURN OFF THE POWER UNTILLOADING COMPLETE.LOAD DATA messageAfter loading is completed, the followingmessage appears.COMPLETE LOADING DATA.PRESS "ENTER" KEYTO CONTINUE.COMPLETE message7.Press the [ENTER] key.Note on loading dataTrackSince loaded track data is added to internaltrack, oldest track will be e rased when thetrack memory capacity is exceeded.Waypoint/routeThe loaded data OVERWRITES previouslystored waypoints and routes. BE CAREFUL NOT TO DESTROY VALUABLE DATA! Mark/lineThe loaded data is added to internal data.When the mark/line memory becomes full nomarks may be entered.ConfigurationThe loaded data replaces current configura-tion settings. Press the [ENTER] key to re-start. If the memory card is ejected whileloading or data could not be loaded, pressthe [ENTER] key to restart with default set-tings. Note that track memory capacity is notsaved or loaded.This section describes the various options which allow you to set up your unit to suit your needs.1CHART SETUP OPTIONSmenuThe chart offset options menu provides three menus: chart offset, track control, and chart detail.1.Press the [MENU] key to open the main menu.2.Press the soft key CHART SETUP OP-TIONS.11-1 Chart setup options menuCUSTOMIZING YOUR UNITCHART OFFSET -NEW FOR NAVIONICSIn some instances position may be off by a few minutes. For example, the position of the ship is shown to be at sea while it is in fact moored at a pier. You can compensate for this error by offsetting chart position as fol-lows:1.Press the [MENU] key followed by the soft keys CHART SETUP OPTIONS and CHART OFFSET.Plotter display,chart offset selectede the cursor pad to place the cursor where to offset chart position.3.Press the soft key SET OFFSET.4.Press the soft key RETURN to finish.To cancel chart offset, press the soft key RE-SET OFFSET at step 3 in the above proce-dure.TRACK CONTROL menuThis menu mainly controls track color and track plotting interval. For further details see Track Chapter.SETUP NMEA/DGPS PORT 2 menu descriptionThis menu should be set according to the specifications of the equipment connected to connectors PORT 1 (NMEA) and PORT 2 (DGPS) at the rear of the display unit. The menu can be displayed by pressing the [MENU] key followed by the soft keys CON-FIGURATION and SETUP NMEA PORT 2. For detailed information, see the installation manual.FORMAT- WITH NEW RTCM(OUTPUT) Selects data format of connected equipment; NMEA0183 version 1.5, version 2.0, RTVM104 (EXTRN), RTCM104 (INTRN) or RTCM104 (OUTPUT). RTCM104 (INTRN) is for "D" versions only. The default setting for non-"D" versions is RT C M104 (EXTRN).The procedure for setting LAT/LON FORMAT is similar to those for PORT 1. Note that you cannot setup data sentences when you select RTCM104 (INTRN) as the format. (A level converter (IF-1432) maybe required when using NMEA0183 format from this port.) LAT/LON FORMAT (GGA only)Selects the seconds of latitude and longitude positions in hundredths, thousandths or ten thousandths of a degree.UPLOAD/DOWNLOAD DATA menuThis menu allows you to upload waypoint and route data to a PC or download the same data from a PC, via the DGPS connector at the back of display unit. The menu can be displayed by pressing the [MENU] key fol-lowed by the soft keys CONFIGURATION and UPLOAD/DOWNLOAD DATA. For de-tailed information, see the installation manual. See previous pages for Memory Card info.upload/download menuDi splay unit, rear viewSet communication software on the PC as follows:Baud Rate: 4800 bpsCharacter Length: 8 bitStop bit: 1 bitParity: NoneX Control: XON/XOFFThe following data can be downloaded/up-loaded between a personal computer and this equipment.•Waypoint data (In alphanumeric order)•Route data (In order of route number)•End of sentenceNote 1: There are two kinds of data for route data: route data and route comment data. Note 2: DGPS position fix is not available when uploading or downloading data.A-scope displayThis display shows echoes at each transmis-sion with amplitudes and tone proportional to their intensities, on the right 1/3 of the screen. It is useful for estimating the kind of fish school and seabed composition.Normal displayA-scope displayplus normal sounder displayNew Wide Plotter/ES DisplayThis display provides the plotter display on the left part of the screen and the normal sounder display on the right part. It is useful for searching fish schools at cruising speed.The width of the sounder display can be se-lected between standard (approx. 20 mm)and wide (approx. 40 mm).1.Press the [MENU] key and the soft key SOUNDER SETUP OPTIONS. The sounder setup menu appears. See Fig-ure 1-9.2.Press w to select E/S WINDOW window.3.Press the soft key EDIT to show the E/S WINDOW window.4.Press v or w to select STD or WIDE.STD: The width of the sounder display is approx. 20 mm (Default setting).WIDE: The width is approx. 40 mm.5.Press the [ENTER] key or the soft key ENTER.Sounder Plotter/Sounder displayDual-frequency display example。

10 Tensione
Common Parts Ref.
1 Pump 3 Hot Gas Coil 4 Hot Gas Valve Body 7 Contactor 9 Bin Thermostat 10 Evaporator Thermostat 11 Timer 12 Green Light Switch
Rev. 3 - 2/7/2003
Ref. 1 - Ice Cubes Slide Kind of Cube Code
18 g. (Standard) 33 g. (Big) 13 g. (Small)
D12022 D12033 D12040
Ref. 6 - Sprayers Bar Ass.
Kind of Cube
ELECTRIC PARTS
Spare Description See Table
See Table
Code
23091 20409 23594 23005 23591
23327
Parts for Air-Cooled Version Only Ref.
2 Fan Motor 6 Inlet Watervalve 1 Way 8 Condenser Pressure Switch 13 Anti Radio Interference Filter
See Table See Table
Version 2 Version 2 Version 2 Version 2 Version 1 Version 1
Code
10005 C22134
D20002 10012 10305 10133 20233 10241 13006 10055 13007 10096 C13110 10007 10009 C13036 20005 10405 13142 10404 13143 13096 13095

Product SpecificationSFP/SFP+ Evaluation BoardFDB-1027Finisar’s FDB-1027 Evaluation Board is the perfect vehicle for testing and evaluating SFP/SFP+ optical transceivers.The board consists of a single SFP+ edgeconnector and cage, four 50-ohm SMA coaxial connectors (J12-J15) for the high-speeddifferential transmitter input and receiver output signals, and test points and LEDs for monitoring all other SFP+ pins. It is compatible with short wavelength and long wavelength SFP/SFP+ transceiver types for use at data rates of 125 Mb/s to 14.025 Gb/s.The FDB-1027 SFP/SFP+ Evaluation Board is supplied with software and a DB-25 cable for communication with a PC parallel port. This cable allows direct communication between the PC and the module via the 2-wire serial bus on pins SCL and SDA, as well as for reading the status lines and setting the TX disable and Rate Select inputs.The software included with the board provides a simple windows-based GUI for monitoring the Serial ID information available in Finisar’s SFP/SFP+ transceivers.Switch (S1) is provided to assert and test the transmit disable function. Switch (S2) isprovided to select the operating bit rate of the receiver (RS0) in multi-rate SFP/SFP+ transceivers that require it. Switch (S3) is provided to select the operating bit rate of the transmitter (RS1) in multi-rate SFP+transceivers that require it. (Note: SFP modules do not support RS1.) TX disable can becontrolled either by the switch or the parallel port; control is determined by the position of the jumper (S4). Similarly, jumpers at (S5) and (S6) govern the RS0 and RS1 controls, respectively.SPECIFICATIONSThe FDB-1027 SFP/SFP+ Evaluation Board can be powered by one or two supply voltage(s) depending on whether the supply for the evaluation board and module need to be separated. A module supply voltage of 3.0 to 3.6V should be supplied at connector J9. If shunt at jumper J2 is removed, a second 3.3V supply can be provided at J1 to separately power the evaluation board.Please refer to module data sheets forspecifications of input signals to the TX+ and TX– connectors and output signals on the RX+ and RX– connectors. SFP/SFP+ transceivers have internal AC coupling on all data lines.The board layout and schematics are shown on pages 2 and 3.Finisar Corporation1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000Fax 1-408-541-6138*****************。