杭州瑞诚 微孔板振荡器 TS200-中文简介

目录一、产品介绍和使用范围 (1)二、性能特点 (1)三、技术指标 (1)四、安装要求 (2)五、操作使用说明 (2)六、注意事项 (7)七、保修期 (7)一、产品介绍和使用范围ZQWY-200卧式恒温振荡培养箱，广泛的应用于微生物、病毒、细菌培养、发酵、杂交和生物化学反应以及细胞组织等研究。

为温度、振荡频率、振幅有不同要求的培养以及酶工程等方面的研究提供了有效的帮助。

在医学生物学、分子学、制药、食品、环保等研究领域有着广泛而重要的作用。

二、性能特点1、LCD大屏幕背光液晶显示，参数的设定、观察清晰直观；2、PID微电脑智能控温仪，控温精确；3、具有定时功能：0～999.9小时内任意设定培养时间；4、采用红外加热管，升温快，耗能少；5、激光测速装置，显示转速与实际转速完全一致，避免了传统的比例测算法出现的实际转速与显示转速之间的误差，转速更加精确可靠；6、三维一体的偏三轮驱动，运转平滑、稳定、耐久、可靠；7、静音风扇设计和强制对流方式，确保了良好的恒温效果；8、具有超温报警功能及异常情况自动断电功能；9、具有断电恢复功能，避免因停电、死机而造成的数据丢失问题；10、采用特种的交流感应无刷电机，使用后故障少、寿命长,免保养。

11、流线型外观，镜面不锈钢内衬，大屏幕玻璃视窗方便随时在不开门情况下观察箱体内部情况，,静电喷塑箱体。

三、技术指标品名恒温振荡培养箱型号ZQWY-200振荡频率40-300rpm振荡频率精度±1rpm摇板振幅Ф26mm温控范围4℃～60℃温度调节精度±0.1℃温度均匀度±1℃显示方式LCD（液晶显示屏）对流方式强制对流控制方式P．I．D微电脑智能控制最大容量单层250ml×54或500ml×40或1000ml×24定时范围0-999.9小时摇板尺寸850×520mm标准配置万能夹具电源AC220±10%50～60Hz外型尺寸（长×宽×高）1330×670×710mm重量170kg四、安装要求1、培养箱应放在平面坚实的台面上；2、安放地点无强烈光照、无强烈腐蚀性气体、相对湿度85%一下；3、室内通风良好，振荡器后背与墙面间距离应大于40公分；4、使用电源：交流220V±10%，50HZ,容量不小于1KW，备有地线的电源插座。

RM3000TDS3012CENCORE TDS3TMT TDS3VID TDS3012CENCOREDigital Phosphor OscilloscopesTDS3000C Series DatasheetThe TDS3000C Series provides you with the performance you need at a price you can afford. Bandwidths range from 100 MHz to 500 MHz, with up to 5 GS/s sample rates for accurate representation of your signal.Key performance specifications100 MHz, 300 MHz, and 500 MHz bandwidth models2 or 4 analog channel modelsSample rates up to 5 GS/s real time on all channels10k record length on all channels3,600 wfms/s continuous waveform capture rate Suite of advanced triggersKey featuresFront-panel USB host port for easy storage and transfer ofmeasurement data25 automatic measurementsFFT standardMultiple language user interfaceWaveAlert ®automatic waveform anomaly detectionTekProbe ® interface supports active, differential, and current probes for automatic scaling and unitsPortable designLightweight design (only 7 lb./3.2 kg) for easy transportOptional internal battery operation provides up to three hours without line powerApplication modules for specialized analysisAdvanced analysis moduleLimit testing moduleTelecommunications mask testing module Extended video moduleApplicationsDigital design and debugVideo installation and servicePower supply designEducation and trainingTelecommunications mask testingManufacturing test General bench testingDPOs provide greater level of insight into complex signalsThe TDS3000C Series offers fast waveform capture rates on a continuous basis that save you time by quickly revealing the nature of faults, so advanced triggers can be applied to isolate them.Real-time intensity grading highlights the details about the history of a signal's activity, making it easier to understand the characteristics of the waveforms you've captured. Unlike other comparable oscilloscopes, thehistory remains even after the acquisition has been stopped. 1Quickly debug and characterize signals with DRT sampling technology and sin (x)/x interpolationThe TDS3000C Series combines unique digital real-time (DRT) sampling technology with sin(x)/x interpolation to allow you to accurately characterize a wide range of signal types on all channels simultaneously. With the TDS3000C Series there is no change in sampling rate when additional channels are turned on, unlike other comparable oscilloscopes. This sampling technology makes it possible to capture high-frequency information, such as glitches and edge anomalies, that elude other oscilloscopes in its class, while sin(x)/x interpolation ensures precisereconstruction of each waveform.Look for unintentional circuit noise with the TDS3000C series’ FFT capability.Custom video triggering allows the TDS3000C Series to trigger on standards such asRS-343 (26.2 kHz scan rate).The TDS3000C Series provides breakthrough test speeds for telecommunications line card testing. The telecom QUICKMENU puts all the commonly used telecom test functions on a single menu.Easy to setup and useWhen working under tight deadlines, you need your oscilloscope to be intuitive; you want to minimize time spent learning and relearning how to use it. The TDS3000C Series oscilloscopes help reduce your learning curve. Simple navigation and dedicated front-panel controls get you to where you want to be quickly, so that you spend less time learning andmore time on the task at hand.The TDS3000C series with the TDS3LIM module is ideal for manufacturing test applications where fast Go/No-Go decisions are required.Datasheet2 WaveAlert waveform anomaly detection alerts you to any waveform that deviates fromthe “normal” input such as the glitch on channel 2.Easily transfer, document, and analyze data on your PC.Simple documentation and analysisThe TDS3000C Series comes equipped with a USB host port so you can easily store and transfer measurement information to your PC.OpenChoice ®PC Communication Software allows you to simply pull screen images and waveform data into a standalone desktop application or directly into Microsoft Word and Excel.If you prefer not to use a PC for analysis, the TDS3000C Series comes standard with 25 automatic measurements, waveform add, subtract, divide,and multiply math functions, and Fast Fourier Transform (FFT). Unlike other comparable oscilloscopes, the TDS3000C Series math andmeasurement allows you to use the full acquisition record length or isolate a specific occurrence within an acquisition.Instrument controlUtilizing the built-in ethernet port, e*Scope web-based remote control allows you to a control TDS3000C series oscilloscope from anywhere,using the internet and your PC.Work where you need toThe TDS3000C Series packs the power of a DPO in a compact design that is only 5.9 in. (149 mm) deep, freeing up valuable benchtop space. And when you need to move your oscilloscope to another lab, its portable 7 lb.(3.2 kg) design makes for easy transport.If your work demands even more mobility, then the optional battery packwill give you up to three hours of operation without line power.TDS3BATC provides you with up to three hours of portable battery operation.TDS3000C Series Digital Phosphor Oscilloscopes 3SpecificationsAll specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.Vertical systemHardware bandwidth limitsInput coupling AC, DC, GNDInput impedance 1 MΩ in parallel with 13 pF or 50 ΩInput sensitivity range1 MΩ 1 mV/div to 10 V/div 50 Ω 1 mV/div to 1 V/div Vertical resolution 9 bits Maximum input voltage1 MΩ150 V RMS with peaks at ≤400 V 50 Ω 5 V RMS with peaks at ≤30 V DC gain accuracy ±2%Position range±5 divHorizontal systemSeconds/division rangeTime base accuracy±20 ppm over any 1 ms time intervalDatasheet4 TDS3000C Series Digital Phosphor Oscilloscopes Trigger systemTrigger modes Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single SequenceB trigger Trigger after time or eventsTrigger after time range13.2 ns to 50 sTrigger after events range 1 to 9,999,999 eventsTrigger typesEdge Conventional level-driven trigger. Positive or negative slope on any channel. Coupling selections: AC, DC, Noise Reject, HFReject, LF RejectVideo Trigger on all lines or individual lines, odd/even or all fields on NTSC, PAL, SECAMExtended video Trigger on specific lines in broadcast and non-broadcast (custom) standards and on analog HDTV formats (1080i, 1080p, 720p,480p). Requires TDS3VID application modulePulse width (or glitch)Trigger on a pulse width <, >, =, ≠ to a selectable time limit ranging from 39.6 ns to 50 sRunt Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first againRise/fall time Trigger on pulse edge rates that are either faster or slower than a set rate. Edges can be rising, falling, or eitherPattern Specifies AND, OR, NAND, NOR when true or false for a specific timeState Any logic state. Triggerable on rising or falling edge of a clock. Logic triggers can be used on combinations of 2 inputs (not 4) Comm Provides isolated pulse triggering required to perform DS1/DS3 telecommunications mask testing per ANSI T1.102 standard.Requires TDS3TMT application moduleAlternate Sequentially uses each active channel as a trigger sourceAcquisition systemDPO Captures and displays complex waveforms, random events and subtle patterns in actual signal behavior. DPOs provide3 dimensions of signal information in real time: Amplitude, time, and the distribution of amplitude over timeSample Sample data onlyAverage Waveform averaged, selectable from 2 to 512Envelope Min-max values acquired over one or more acquisitionsPeak detect High-frequency and random glitch capture. Captures glitches as narrow as 1 ns (typical) using acquisition hardware at all timebase settingsWaveAlert®Monitors the incoming signals on all channels and alerts the user to any waveform that deviates from the normal waveform beingacquiredSingle sequence Use the Single Sequence button to capture a single triggered acquisition sequence at a time 5DatasheetWaveform measurementsCursors Amplitude, timeAutomatic measurements Display any four measurements from any combination of waveforms. Or display all measurements with measurement snapshotfeature. Measurements include Period, Frequency, +Width, -Width, Rise time, Fall time, +Duty cycle, -Duty cycle, +Overshoot,High, Low, Max, Min, Peak-to-peak, Amplitude, Mean, Cycle mean, RMS, Cycle RMS, Burst width, Delay, Phase, Area 1, CycleArea 1Measurement statistics Mean, Min, Max, Standard deviation. Requires TDS3AAM application moduleThresholds User-definable thresholds for automatic measurements; settable in percent or voltageGating Isolate a specific occurrence within an acquisition to take measurements, using either the screen or cursorsWaveform mathArithmetic Add, subtract, multiply, and divide waveformsFFT Spectral magnitude. Set FFT vertical scale to Linear RMS or dBV RMS, and FFT window to Rectangular, Hamming, Hanning, orBlackman-HarrisAdvanced math Integrate, differentiate, define extensive algebraic expressions including analog waveforms, math functions, scalars, up to twouser-adjustable variables and results of parametric measurements. For example: (Intg (Ch1-Mean(Ch1)) × 1.414 × VAR1) 2Waveform processingAutoset Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo autosetDeskew Channel-to-channel deskew ±10 ns may be manually entered for better timing measurements and more accurate math waveformsDisplay systemDisplay type 6.5 in. (165.1 mm) liquid-crystal TFT color displayDisplay resolution640 horizontal × 480 vertical pixels (VGA)Interpolation Sin(x)/xWaveform styles Dots, vectors, variable persistence, infinite persistenceGraticules Full, grid, crosshair, and frame. NTSC, PAL, SECAM, and vectorscope (100% and 75% color bars) with optional TDS3VIDapplication moduleFormat YT, XY, and Gated XYZ (XY with Z-axis blanking available on 4-channel instruments only)1Requires TDS3AAM application module.2Requires TDS3AAM application module.6 Input/output portsEthernet port RJ-45 connector, supports 10Base-T LANUSB port Front-panel USB 2.0 host port. Supports USB flash driveGPIB port Full talk/listen modes, setting and measurements.(Optional with TDS3GV Communications Module)RS-232C port DB-9 male connector, full talk/listen modes; control of all modes, settings and measurementsBaud rates up to 38,400(Optional with TDS3GV Communications Module)VGA video DB-15 female connector, monitor output for direct display on large VGA-equipped monitors(Optional with TDS3GV communications module)External trigger input BNC connector, input impedance >1 MΩ in parallel with 17 pF; max input voltage is 150 V RMSPower sourceAC line powerSource voltage100 V RMS to 240 V RMS ±10%Source frequency45 Hz to 440 Hz from 100 V to 120 V45 Hz to 66 Hz from 120 V to 240 VPower consumption75 W maximumBattery power Requires TDS3BATC, rechargeable lithium ion battery packOperating time, typical 3 hoursPhysical characteristicsDimensionsWeightPackage dimensionsRackmount (RM3000)TDS3000C Series Digital Phosphor Oscilloscopes 7DatasheetEMC, environment and safetyTemperatureOperating0 ºC to +50 ºCNon-operating-40 ºC to +71 ºCHumidity(Operating and non-operating)At or below +30 ºC Up to 95% RH+30 ºC up to +50 ºC Up to 45% RHAltitudeOperating To 3,000 metersNon-operating15,000 metersElectromagnetic compatibility Meets or exceeds EN61326 Class A, Annex D radiated and conducted emissions and immunity; EN6100-3-2 AC PowerlineHarmonic Emissions; EN6100-3-3 Voltage Changes, Fluctuation, and Flicker; FCC 47 CFR, Part 15, Subpart B, Class A;Australian EMC frameworkSafety UL61010B-1, CSA1010.1, IEC61010-1, EN61010-1Ordering informationTDS3000C familyTDS3012C100 MHz, 2 channels, 1.25 GS/sTDS3014C100 MHz, 4 channels, 1.25 GS/sTDS3032C300 MHz, 2 channels, 2.5 GS/sTDS3034C300 MHz, 4 channels, 2.5 GS/sTDS3052C500 MHz, 2 channels, 5 GS/sTDS3054C500 MHz, 4 channels, 5 GS/sPlease specify a language option and a power plug option from the lists that follow.8 Standard accessoriesProbesP6139B500 MHz 10x passive probe, one per channel AccessoriesFront protective coverAccessory trayDocumentation CD Contains User Manuals in all languagesFront panel overlay Translated front panel overlay. Specify language option.Installation and Safety ManualPower cord Specify power plug option.OpenChoice® PC connectivity software Enables fast and easy communication between Windows PC and the TDS3000C Series through LAN, GPIB, or RS-232. Transfer and save settings, waveforms, measurements, and screen imagesTraceable Certificate of Calibration NIM/NISTWarrantyThree year warranty covering all labor and parts, excluding probes and accessoriesInstrument optionsPower plug optionsOpt. A0North America power plug (115 V, 60 Hz)Opt. A1Universal Euro power plug (220 V, 50 Hz)Opt. A2United Kingdom power plug (240 V, 50 Hz)Opt. A3Australia power plug (240 V, 50 Hz)Opt. A4North America power plug (240 V, 50 Hz)Opt. A5Switzerland power plug (220 V, 50 Hz)Opt. A6Japan power plug (100 V, 50/60 Hz)Opt. A10China power plug (50 Hz)Opt. A11India power plug (50 Hz)Opt. A12Brazil power plug (60 Hz)Opt. A99No power cordTDS3000C Series Digital Phosphor Oscilloscopes 9DatasheetLanguage optionsOpt. L0English manualOpt. L1French manualOpt. L2Italian manualOpt. L3German manualOpt. L4Spanish manualOpt. L5Japanese manualOpt. L6Portuguese manualOpt. L7Simplified Chinese manualOpt. L8Traditional Chinese manualOpt. L9Korean manualOpt. L10Russian manualOpt. L99No manualLanguage options include translated front-panel overlay for the selected language(s). Service optionsRecommended accessoriesProbesADA400A100x, 10x, 1x, 0.1x high-gain differential amplifier P5100A 2.5 kV, 100x high-voltage passive probeP5205A 1.3 kV, 100 MHz high-voltage differential probe P5210A 5.6 kV, 50 MHz high-voltage differential probe P6243 1 GHz, ≤1 pF input C 10x active probeTCP202A50 MHz, 15 A AC/DC current probeTCP30315 MHz, 150 A current probe 3TCP305A50 MHz, 50 A current probe 3TCP312A100 MHz, 30 A current probe 3TCPA300100 MHz probe amplifier3Requires TCPA300 probe amplifier.TCPA40050 MHz probe amplifierTCP404XL 2 MHz, 500 A current probe 4AccessoriesTDS3GV GPIB, VGA, RS-232 interfaceTDS3AAM Advanced Analysis Module. Adds extended math capability, arbitrary math expressions, measurement statistics, and additionalautomated measurementsTDS3LIM Limit Testing Module. Adds custom waveform limit testing capabilitiesTDS3TMT Telecom Mask Testing Module. Adds pass/fail compliance of ITU-T G.703 and ANSI T1.102 standards, custom mask testing, andmoreTDS3VID Extended Video Analysis Module. Adds video quickmenu, autoset, hold, line count trigger, video picture mode, vectorscope 5mode, HDTV format trigger graticules, and moreTDS3BATC Lithium-ion battery pack for up to 3 hours continuous operation without line powerTDS3ION Battery chargerAC3000Soft case for carrying instrumentHCTEK4321Hard plastic case for carrying instrument(requires AC3000)RM3000Rackmount kit071-2507-xxService manual (English only)Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.4Requires TCPA400 probe amplifier.5Vectorscope does not support composite video.TDS3000C Series Digital Phosphor OscilloscopesDatasheetASEAN / Australasia (65) 6356 3900 Austria 00800 2255 4835*Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Belgium 00800 2255 4835*Brazil +55 (11) 3759 7627 Canada180****9200Central East Europe and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401Finland +41 52 675 3777 France 00800 2255 4835*Germany 00800 2255 4835*Hong Kong 400 820 5835 India 000 800 650 1835 Italy 00800 2255 4835*Japan 81 (3) 6714 3010 Luxembourg +41 52 675 3777 Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90Middle East, Asia, and North Africa +41 52 675 3777 The Netherlands 00800 2255 4835*Norway 800 16098People's Republic of China 400 820 5835 Poland +41 52 675 3777 Portugal 80 08 12370Republic of Korea +822 6917 5084, 822 6917 5080 Russia & CIS +7 (495) 6647564 South Africa +41 52 675 3777Spain 00800 2255 4835*Sweden 00800 2255 4835*Switzerland 00800 2255 4835*Taiwan 886 (2) 2656 6688 United Kingdom & Ireland 00800 2255 4835*USA180****9200* European toll-free number. If not accessible, call: +41 52 675 3777For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit . Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification andprice change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.26 Aug 2016 41W-12482-25 TDS3VID TDS3012C TDS3032C TDS3034C TDS3052C TDS3054C TDS3014C TDS3BATC TDS3GV TDS3TMTRM3000TDS3012CENCORE TDS3TMT TDS3VID TDS3012CENCORE。

（可用于深孔板培养）
1．产品简介与特点
TS300微孔板专用恒温振荡器是一款由直流无刷电机和PID智能控温技术相结合的多用途恒温振荡器。

其PID模糊控制技术能够精准的确保控温精度，并自动调整加热速率节省等待时间。

TS300将恒温和振荡两种功能完美地结合在一起，极大地缩短了实验操作的时间，是样品孵化、催化、混匀及保存等反应过程理想的自动化工具。

本产品具有以下特点：
●简单易用的人机操作界面，实时显示全部运行信息和设置信息，方便用户观
察设备运行状态。

●一次可处理4块酶标板或者深孔板。

●采用直流无刷电机，噪音低、干扰小、免维护。

●采用热盖加热技术。

●支持自动预热功能。

●支持断电自动恢复功能。

●自带温度校准功能。

●内置软件和硬件双重超温保护装置，使用更可靠。

2．正常工作条件
使用环境温度：0︒C ~ 35︒C
相对湿度：≤70%
使用电源：AC220V/50-60HZ
3. 基本参数。

目录Infinite 200 Pro多功能微孔板检测仪简介3 M200 Pro和F200 Pro的性能和技术指标5技术详解91.关于M200 Pro的四光栅系统92.关于M200 Pro的荧光顶部Z轴自动连续聚焦103.关于F200 Pro的优异性价比114.关于F200 Pro的智能滤光片盒115.关于荧光底部的Optimal read126.关于Infinite 200 Pro的发光光路127.关于Nanoquant微量检测板138.关于GCM14销售策略151.产品定位与目标用户152.关键卖点15Infinite 200 Pro多功能微孔板检测仪简介Infinite系列多功能微孔板检测仪由Tecan集团下属的奥地利公司设计并生产。

秉承Tecan对创新和性能的一贯追求，Infinite系列产品包括了多项先进技术，并提供一流的检测灵敏度和稳定性。

Infinite 200 Pro包括M和F两个型号，分别对应光栅型（monochromator）和滤光片型（filter）。

由于采用先进的模块化的设计，不仅能满足当今科研领域的多样化需求，提供了灵活、可扩展的配置方案，还能保证各项功能都获得最佳的检测效果。

Infinite M200 Pro光栅型多功能检测仪提供以下检测功能：●全波长连续可调的光吸收检测●全波长连续可调的荧光顶部检测●全波长连续可调的荧光底部检测●全波长连续可调的时间分辨荧光检测●荧光顶部自动Z轴聚焦●OR（Optimal Read）增强荧光底部检测●闪光和辉光型发光检测，包括双色发光和BRET●支持6-384孔、立式比色杯和卧式比色杯●Nanoquant 微量检测板，可进行核酸、蛋白定量，及荧光探针标记效率测定●气体控制模块，可控制仪器内部O2和CO2浓度●有效的温控和振幅可调的振荡功能●双自动进样器Infinite F200 Pro滤光片型多功能检测仪提供以下检测功能：●光吸收检测，滤光片覆盖紫外至远红外●荧光顶部检测，滤光片覆盖紫外至远红外●荧光底部检测，滤光片覆盖紫外至远红外●时间分辨荧光检测，●均相时间分辨荧光检测●荧光偏振检测●AlphaScreen/AlphaLISA检测●OR（Optimal Read）增强荧光底部检测●智能滤光片盒，内置芯片记录滤光片信息，仪器自动识别●闪光和辉光型发光检测，包括双色发光和BRET●支持6-384孔和卧式比色杯●Nanoquant 微量检测板，可进行核酸、蛋白定量●气体控制模块，可控制仪器内部O2和CO2浓度●有效的温控和振幅可调的振荡功能●双自动进样器Infinite 200 Pro系列的突出特点Infinite M/F200 Pro专注于仪器性能以及科学家的需求，受到严肃、有经验、追求优异实验结果的科学家的深度认可。

微孔板快速振荡器检验标准
摘要：
一、微孔板快速振荡器的工作原理与作用
二、微孔板快速振荡器的分类与特点
三、微孔板快速振荡器的使用方法与操作步骤
四、微孔板快速振荡器的维护与注意事项
五、微孔板快速振荡器的检验标准与要求
正文：
微孔板快速振荡器是一种实验室常用的设备，其工作原理是通过电机驱动振荡装置，使微孔板在设定的温度和湿度条件下进行快速振荡，以达到实验目的。

微孔板快速振荡器在医学、生物学、化学等领域都有着广泛的应用。

微孔板快速振荡器有多种分类，可以根据振荡频率、温度范围、体积等不同特点进行分类。

例如，根据振荡频率可分为低频振荡器、中频振荡器、高频振荡器；根据温度范围可分为常温振荡器、高温振荡器、低温振荡器等。

不同类型的微孔板快速振荡器适用于不同的实验需求。

微孔板快速振荡器的使用方法相对简单，一般来说，首先需要将微孔板放入振荡器中，然后设定振荡条件，启动振荡器，最后取出微孔板即可。

在使用过程中，需要注意操作步骤的规范性，以保证实验结果的准确性。

微孔板快速振荡器的维护也非常重要，一般来说，需要定期清洁振荡器，避免灰尘和污垢影响振荡效果。

此外，还需要定期检查振荡器的电路和机械部件，确保其正常工作。

微孔板快速振荡器的检验标准主要包括振荡频率、振荡幅度、温度控制精度等。

在购买微孔板快速振荡器时，需要根据实验需求选择符合检验标准的设备，以确保实验结果的准确性。

总之，微孔板快速振荡器是一种非常重要的实验室设备，其工作原理、分类、使用方法、维护以及检验标准都需要我们掌握。

FST200-00系列传感器终端使用说明书此说明书适用于下列型号产品：客户热线：400-8838-199电话：+86-592-6300320传真：+86-592-5912735网址：地址：厦门集美软件园三期A06栋11层FST200-00系列传感器终端使用说明书文档版本密级V1.0.1产品名称：FST200共39页型号产品类别FST200-00LA 频段：410-510MHz ，电池供电设备，正常应用于国内FST200-00HA 频段：863-928MHz ，电池供电设备，正常应用于国外FST200-00LC 频段：410-510MHz ，DC 供电设备，正常应用于国内FST200-00HC频段：863-928MHz ，DC 供电设备，正常应用于国外文档修订记录日期版本说明作者2022-09-23V1.0.0初始版本CYD 2022-02-21V1.0.1更新LoraWan信息，透传、FT模式ZJX著作权声明本文档所载的所有材料或内容受版权法的保护，所有版权由厦门四信通信科技有限公司拥有，但注明引用其他方的内容除外。

未经四信公司书面许可，任何人不得将本文档上的任何内容以任何方式进行复制、经销、翻印、连接、传送等任何商业目的的使用，但对于非商业目的的、个人使用的下载或打印（条件是不得修改，且须保留该材料中的版权说明或其他所有权的说明）除外。

商标声明Four-Faith、四信、、、均系厦门四信通信科技有限公司注册商标，未经事先书面许可，任何人不得以任何方式使用四信名称及四信的商标、标记。

目录第一章产品简介 (6)1.1产品概述 (6)1.2产品特点 (6)1.3工作原理框图 (7)1.4产品规格 (7)第二章安装 (10)2.1装箱清单 (10)2.2外观 (10)2.3产品尺寸(mm) (11)2.4按键说明 (11)2.5产品安装 (11)第三章参数配置 (13)3.1配置工具 (13)3.2配置步骤 (14)3.3LoRa配置 (16)3.4基本设置 (18)3.5接口设置 (21)3.6维护（批量配置） (23)第四章四信传感云 (25)4.1快速添加设备 (25)1、选择F8926-L定制版 (25)4、通过四信传感云平台，添加网关设备 (25)第五章对接客户平台配置 (27)5.1网关“API”模式 (27)1、“工作模式”选择“API” (27)3、“服务端地址”和“服务端端口”填写要连接的服务器 (27)5.2网关“TRNS”模式 (28)1、“工作模式”选择“TRNS” (28)3、“服务端地址”和“服务端端口”填写要连接的服务器 (29)第六章应用层数据通信协议 (30)6.1透传模式 (30)1.不开启数据合并 (31)2.开启数据合并 (31)2.1.整包合并 (31)2.2.Modbus方式合并 (32)6.2FT模式 (33)第一章产品简介1.1产品概述FST200-00系列传感器终端采用工业级32位通信处理器，集成四信自研LoRa模组，具备边缘采集、多样化接口，NFC配置等多种功能的传感器终端，结合IP67高防护等级防水防尘外壳，适用于各种恶劣外部环境。

IR2153 是一种高压、高速、带有高低端驱动的半桥驱动器.该器件前级可调振荡器的功能与大家熟知的555 时基电路相似.驱动器的输出带有缓冲单元,可设定内部死区时间,防止桥路中的两只功率开关管直通.高、低端管子具有延时匹配, 适用于占空比为50 %的场合,该器件可驱动N 沟道功率MOSFET 或IG2B T .IR2153 具有以下特点:●带自举二极管的浮动设计, 最大耐压为600V ;●允许瞬时负压;●欠压保护;●内部振荡器频率可调整;●高、低通道匹配的死区时间;●起动电流很小,仅为90μA ;●高、低通道的关断功能;●低通道输出电压波形与RT 端电压波形相同.2. 内部结构及引脚功能IR2153 内部由放大器、触发器、逻辑控制电路、驱动器及功率电路等构成,如图1 所示.该器件采用双列8 引脚封装, 引脚定义及形式如图2 所示.脚1 (VCC ) :低端逻辑和内部MOS 管的门极驱动电源电压.脚2 (RT ) : 振荡器定时电阻输入端.此端电压波形与半桥高端(脚7) 相同.脚3 (CT ) : 振荡器●新特器件应用节能灯驱动电路IR2153 及应用湖北省电子产品质量检验所胡大友摘要: IR2153 是美国国际整流器公司( IR) 推出的电子镇流器控制专用集成电路.本文描述了IR2153 的主要特点、引脚功能, 简要介绍了该器件的电气参数, 并着重讲述了实际应用电路.关键词:电子镇流器驱动IR2153 应用图1 IR2153 功能框图图2 IR2153 引脚图© 1995-2004 Tsinghua Tongfang Optical Disc Co., Ltd. All rights reserved.节能灯驱动电路IR2153 及应用- 7 -定时电容输入端.应用时, 该脚和COM (脚4)之间应接一电容,以便调整振荡器频率.f =11. 4 (R T + 75Ω)CT(式中,75Ω 是输出级的等效电阻) .脚4(COM) :低端返回端.脚5(LO) :低端门极驱动输出端.脚6(VS ) :高端浮动电源返回端.脚7(HO) :高端门极输出驱动端.脚8(VS ) : 高端MOS 管门极驱动浮动电源.3. 电气参数3. 1 极限参数IR2153 的极限参数如表1 所列.3. 2 静态电气参数IR2153 的静态电气参数如表2 所列.3. 3 动态电气参数IR2153 的动态电气参数如表3 所列.4. 器件应用4. 1 典型应用电路IR2153 可驱动MOSFET 或IGB T .典型应用电路如图3 所示.图4、图5、图6 分别为电路的输入/ 输出波形、开关时间波形及死区时间波形图.表1 IR2153 的极限参数参数名称符号参数值最小值最大值单位高端浮动电压VB - 0. 3 62 V高端补偿电压V S VB - 25 VB + 0. 3 V高端输出电压V HO VS - 0. 3 VB + 0. 3 V低端输出电压VLO - 0. 3 VCC + 0. 3 VR T 电压V R T - 0. 3 VCC + 0. 3 VCT 电压V CT - 0. 3 VCC + 0. 3 V电源电流ICC — 25 mAR T 输出电流IR T - 5 5 mA耗散功率PD — 1. 0 (0. 625) W存贮温度TS - 55 150 ℃焊接温度(10s) TL — 300 ℃表2 IR2153 的静态电气参数参数名称符号参数值最小典型最大单位条件振荡频率fOSC —20. 0100— kHzR T = 35. 7kΩR T = 7. 04kΩ2/ 3 V CC 阈电压V CT+ — 8. 0 — V1/ 3 V CC 阈电压V CT - — 4. 0 — VR T 输出高电压V R T+ —0 100200 300mVIR T = - 100μAIR T = - 1mAR T 输出低电压V R T - —20 50200 300mVIR T = 100μAIR T = 1mA输出高电压V OH —— 100 mV IO = 0A输出低电压V OL —— 100 mV IO = 0A表3 IR2153 的动态电气参数参数名称符号参数值最小典型最大单位开通时间t r — 80 — ns关闭时间tf — 35 — ns高端输出电压tsd — 660 — ns低端输出电压DT — 1. 2 —μsR T 占空比D — 50 — %© 1995-2004 Tsinghua Tongfang Optical Disc Co., Ltd. All rights reserved. - 8 - 《国外电子元器件》1998 年第9 期1998 年9 月电源专辑图3 IR2153 典型应用电路图5 开关时间波形图4 输入/ 输出波形图6 死区时间波形4. 2 实用电路IR2153 可应用于高性能电子镇流器.实际电路如图7 所示.4. 2. 1 功能描述该电路由功率因数校正电路、镇流器控制电路、谐振输出电路和保护电路等部分组成.功率因数校正器采用电流连续型升压变换器.镇流器控制电路为传统的RCL 串并联谐振控制电路, 适用于多种类型的灯管.保护电路包括灯管的电流检测和逻辑比较电路, 实现安全断开和平滑再启动的电路等.4. 2. 2 电子镇流器电气特性图7 所示的电子镇流器的电气特性如表4所列.4. 2. 3 镇流器控制电路镇流器控制电路由IR2153 ( IC3) 和R 18 、表4 电子镇流器电气特性表参数名称参数值单位灯管类型2/ 32 T8 2/ 40 T12输入功率65 80 W输入电流(120V AC) 0. 55 0. 67 A预热输出频率60 45 kHz预热输出电压300 300 VP预热时间1. 0 2. 0 s输出频率50 35 kHz输出电压100 100 V交流输入电压90~275V AC/ 50/ 60Hz V直流输入电压100~350 V温度0~70 ℃功率因数0. 99 /谐波总含量< 15 %最大输出电压650 VP© 1995-2004 Tsinghua Tongfang Optical Disc Co., Ltd. All rights reserved. - 9 -R 19 、R 20 、C12 、C13 、C15 、D10 、M 3 等构成.通过控制MOSFET 实现灯管预热、点亮和运行.在预热阶段, 控制电路以固定的频率驱动半桥电路中的MOSFET 管, 使灯管的阴极加热到适当的发光温度, 保证灯丝及灯管具有较长的使用寿命.预热后, 驱动信号的频率迅速降低,超过谐振频率到达最后的工作频率,在这个过程中, 灯管以额定功率工作.不同阶段的频率由IR2153 外接的RT 和CT 值决定.C13 和C15 串联决定预热频率:f ph =C13 + C151. 4 (R 20 ) (C13 ) (C15 )当C12 两端的电压达到D10 的导通电压时, M3 导通, C15 被短路, 此时的工作频率为运行频率,即:f ru n =11. 4 (R 12 ) (C13 )4. 3 应用注意事项IR2153 内部VCC和COM 脚之间有一个齐纳箝位二极管, 通常可将整流后的电源电压经一高阻值电阻加到器件的VCC脚,并在VCC脚和COM 脚之间加一个去耦电容器.应该特别注意的是: 该电路不能用输出电压高于UCL AM 的低输出阻抗的直流电源供电.。