w/ DiodeSymbol Test ConditionsMaximum RatingsV CES T C = 25°C to 150°C 600 V V CGR T J = 25°C to 150°C, R GE = 1M Ω 600 V V GES Continuous ± 20 V V GEM Transient ± 30 V I C25 T C = 25°C 60A I C110 T C = 110°C 30 A I CM T C = 25°C, 1ms150A SSOA V GE = 15V, T VJ = 125°C, R G = 5Ω I CM = 60 A (RBSOA) Clamped Inductive Load @ ≤ V CES P C T C = 25°C220W T J -55 ... +150 °C T JM 150 °C T stg -55 ... +150°C T L 1.6mm (0.062 in.) from Case for 10s 300 °C T SOLD Plastic Body for 10 seconds260°CM dMounting Torque (TO-220) 1.13/10 Nm/lb.in.Weight TO-220 2.5 gTO-263 3.0 gSymbol Test ConditionsCharacteristic Values(T J = 25°C Unless Otherwise Specified) Min. Typ. Max.BV CES I C = 250μA, V GE = 0V 600VV GE(th) I C = 250μA, V CE = V GE 4.0 5.5 VI CES V CE = V CES , V GE= 0V75 μAT J = 125°C500 μAI GES V CE = 0V, V GE = ± 20V±100 nAV CE(sat)I C = 20A, V GE = 15V, Note 12.63.0 V T J = 125°C1.8 VCES I C110 = 30A V CE(sat) ≤ 3.0V t fi(typ) = 47nsHigh-Speed PT IGBTs for 40-100kHz SwitchingIXGP30N60C3D4Features Optimized for Low Switching LossesSquare RBSOA Anti-Parallel Ultra Fast Diode International Standard PackagesAdvantages High Power DensityLow Gate Drive RequirementApplicationsPower InvertersUPS Motor Drives SMPS PFC Circuits Battery Chargers Welding Machines Lamp Ballasts High Frequency Power InvertersG = Gate D = Collector S = EmitterTab = CollectorTO-263 AA (IXGA)G EC (Tab)GC ETO-220AB (IXGP)C (Tab)1 = Gate2 = Collector3 = Emitter4 = CollectorTO-220 Outline IXYS Reserves the Right to Change Limits, Test Conditions and Dimensions.IXYS Reserves the Right to Change Limits, Test Conditions and Dimensions.Fig. 23. Peak reverse current I RMFig. 22. Reverse recovery charge Q r Fig. 21. Forward current I F versus V F Fig. 24. Dynamic parameters Q r , I RMFig. 25. Recovery time t rr versus -di F /dt Fig. 26. Peak forward voltage V FR and Fig. 27. Transient thermal resistance junction-to-caseNOTE: Fig. 2 to Fig. 6 shows typical values200600100004008004060801000.000010.00010.0010.010.110.0010.010.1110040801201600.00.51.01.52.0K f T VJC -di F /dtts K/W0200400600800100002040600.00.10.20.3V FRdi F /dtV 2006001000040080024681010010000501001502002500123051015202530I RMQ rI FAV F-di F /dt-di F /dtA/μs AVnCA/μs A/μs t rrnst frZ thJCA/μs μsI RMQ r分销商库存信息: IXYSIXGP30N60C3D4。
元器件交易网IMPORTANT NOTICETexas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinueany product or service without notice, and advise customers to obtain the latest version of relevant informationto verify, before placing orders, that information being relied on is current and complete. All products are soldsubject to the terms and conditions of sale supplied at the time of order acknowledgement, including thosepertaining to warranty, patent infringement, and limitation of liability.TI warrants performance of its semiconductor products to the specifications applicable at the time of sale inaccordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extentTI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarilyperformed, except those mandated by government requirements.CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OFDEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICALAPPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, ORWARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHERCRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TOBE FULLY AT THE CUSTOMER’S RISK.In order to minimize risks associated with the customer’s applications, adequate design and operatingsafeguards must be provided by the customer to minimize inherent or procedural hazards.TI assumes no liability for applications assistance or customer product design. TI does not warrant or representthat any license, either express or implied, is granted under any patent right, copyright, mask work right, or otherintellectual property right of TI covering or relating to any combination, machine, or process in which suchsemiconductor products or services might be or are used. TI’s publication of information regarding any thirdparty’s products or services does not constitute TI’s approval, warranty or endorsement thereof.Copyright © 1998, Texas Instruments Incorporated。
