幕墙专业词汇中英文对照表

幕墙设计中英文对照东铝质集团*CW~ 玻璃幕墙Curtain Wall EL~ 总平立剖面WW~ 带型窗Window Wall PE~ 局部平立剖面AC~ 铝板幕墙Alum Cladding DT~ 节点SC~ 不锈钢挂板Stainless Steel Cladding WD 铝窗WindowGC 花岗石外墙挂板Granite Cladding LV 百叶窗LouverFT 特别设计装饰件Special Feature SL 天窗SkylightGW 玻璃墙Glass Wall SF 橱窗StorefrontBT 栏杆Balustrade GR 窗花GrillsMA 旗杆Mast CP雨蓬Canopy～1～平面图PLAN 立面图ELEVATION 剖面图SECTION柱PILLAR 梁GIRDER 桁架TRUSS水槽CUTTER 排水孔WEEP HOLE 水泥砂浆CEMENT GROUT 轴线AXIS 分格尺寸MODULE DIMENSION横向节点图MULLION DETAIL 竖向节点图TRANSOM DETAIL幕墙CURTAIN WALL 室外装饰层EXTERNAL FINISH防水涂层WATERPROOF 室内天花板INTERIOR CEILING室内外完成面EXTR AVENTRICULAR(INTERIOR) FLOOR BY OTHERS～2～铝型材ALUMINIUM EXTRUSION氟碳喷涂铝板ALUM.CLADDING PVF2.PANEL铝板、铝片ALUM. PANEL复合铝板COMPOSITES ALUM. PANEL铝夹(黑色电镀) ALUM. CLIP(BLACK ANODIZED)铝竖框ALUM. MULLION铝窗台板ALUM. SILL BOARD铝横框ALUM. TRANSOM铝托架ALUM. STOOL TRIMMING铝框ALUM. FRAME铝窗廉盖ALUM. PLEMET COVER铝通ALUM. HOLLOW铝（盖）装饰条ALUM. COVER铝套筒ALUM. SLEAVE铝扁巴（条）ALUM. FLAT BAR铝背板ALUM. BACK PAN铝百叶ALUM. LOUVRE接驳件SPIDER FIXING铝管ALUM. CHANNEL铝角ALUM. ANGLE铝锚托架ALUM. ANCHOR BRACKET铝轻型槽ALUM. LIGHT TROUGH铝锚片ALUM. ANCHOR PLATE铝垫圈ALUM. WASHER PLATE (6063-T6)磨光边框GLAZING FRAME铝型材ALUM. EXTRUSION锯齿垫圈SERRATED WASHER铝副框ALUM. ADAPTOR铝基板ALUM. SILL BOARD铝角立柱CORNER ALUM. MULLION (6063-T6) PVF2 FINISH铝横梁盖ALUM. TRANSOM COVER (6063-T5) PVF2 FINISH铝水槽ALUM. GUTTER铝窗扇ALUM. WINDOW SASHALUM. TRIMMING铝支架ALUM. SUPPORT铝压板ALUM. PRESSER～3～钢结构STEEL FRAME 钢构件STEEL WORK铝通STEEL HOLLOW“工”字钢STEEL “I”BEAM冷弯钢ECONOMIC STEEL矩形钢管REC. STEEL TUBE 镀锌槽钢G.M.S. CHANNEL镀锌角钢G.M.S. ANGLE STEEL 镀锌钢板G.M.S. PLATE镀锌钢（垫）介子G.M.S. WASHER 不锈钢折弯槽S.S. BEND CHANNEL不锈钢STAINLESS STEEL（S.S.）预埋件G.M.S.EMBED不锈钢“T”型梁S.S. “T”BEAM “T”型钢STEEL T SECTION发丝不锈钢板S.S. PLATE(HAIRLINE FINISH) 钢管STEEL TUBE石板FLAG STONE～4～密封胶（防水胶）WEATHERSEAL SEALANT 结构胶STRUCTURAL SEALANT 绝缘垫片ISOLACTION SHEET 双面胶带DOUBLE SIDE TAPE 玻璃密封胶（夹胶玻璃专用密封胶）BETA-SEAL 海绵条SPONGE防潮板WATERPROOF 橡胶条GASKET聚脂塑料填塞棒（小圆棒）BACKER ROD 垫片SHIM保温棉THERMAL INSULATION 橡胶垫块EPDM SEALANT1小时防火棉 1 HOUR FIRE STOP INSULATION 地脚螺栓TRUSS BOLT化学螺栓CHEMICAL BOLT 膨胀螺栓EXPANSION BOLT不锈钢平头螺栓S.S. F.H. BOLT (F.H.S) 埋头螺丝DORMANT SCREW 不锈钢六角头螺栓配垫片S.S. H.E.X. HEAD BOLT&WASHER不锈钢沉头螺丝S.S. F.H. SCREW 不锈钢盘头螺丝(P.H.S) S.S. P.H. SCREW植钉STUD ALUM.钢钉DRIVING PIN 射钉PIN铝铆钉ALUM. RIVEM5x15 S.S PH. SELF TAPPING SREW M5x15 不锈钢自攻螺钉: Machine Screw: 机械螺丝B: T apping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝E: Self Drilling Screws 钻尾螺丝（不锈钢钻尾螺丝，复合材料钻尾螺丝）E-1:STAINLESS STEEL SELF DRILLING SCREWS 不锈钢钻尾螺丝E-2:Bi-Metal Self Drilling Screws 复合材料钻尾螺丝～4～（玻璃）中空玻璃RISION INSULATION GLASS 夹胶玻璃LAMINATED GLASS钢化清玻璃CLEAR IRON TEMPERED GLASS 玻璃栏杆GLASS BALUSTER单片玻璃MONOLITHIC GLASS12(LOW-E)+12A+12钢化中空玻璃12HS LOW-E+12+12HS INSULATING GLASS8mm钢化玻璃(加铝背板) 8mm HS OPAQUE GLASS(ALUMINIUM BACK PAN)～4～（其它）厚度THK.ALUM. ADAPTER 铝附框ALUM. PRESSER 铝压板MULTI-POINT LOCKING DEVICE 锁点LOCK BOX W/REMOV ABLE HANDLE锁箱（手柄可拆卸）钢通STEEL. HOLLOWCEMENT GROUTINE 水泥防水砂浆WALL CENTRE LINE 墙中心线保温钉AL. FIXING PIN隔离垫块1mm PVC ISOLATORTHERMAL BREAK 断桥幕墙强度要求σ＜[σ]；幕墙刚度要求，当跨度小于 4.5米，铝质龙骨满足相对挠度，净跨/175和绝对挠度19mm较小者，当跨度在4.5至12米之间，铝质龙骨满足相对挠度，跨度/240和绝对挠度38mm较小者，钢质龙骨满足相对挠度，净跨/250。

门窗、幕墙常用语中英文对照1、表面处理、热处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理2、螺丝产品名称（螺丝螺）六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS)大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航太用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS 不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS3、螺丝产品名称(线材)中英文对照合金钢线材盘元ALLOY STEEL WIRE ROD球状化线材ANNEALING WIRE AND ROD 黑铁丝BLACK WIRE黄铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHATE BRONZE WIRE不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机AIR RIVETER各式螺丝类产品自动包装AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING自动包装机AUTOMATIC PACKING MACHINE螺丝制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE螺丝制造成型机械AUTOMATIC TRIMMING MACHINE拉钉打头机BLIND RIVET HEADING MACHINE螺丝、螺帽成型机BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理BOLT NUT AND SCREWS HEAT TREATMENT螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEAT TREATMENT FURNACES球状化电器炖炉CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE超防锈复合瓷膜CERAMIC COATING连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光辉?#123;质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE中、高热镀涔廨x连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺丝钻孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火炉GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE 十字冲模HEADER PUNCHES IN VARIOUS DRIVES成型冲模HEADER PUNCHES IN VARIOUS DRIVES螺丝打头机HEADING MACHINE螺丝制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打头机HOLLOW HEADING MACHINE热浸镀渎萁z、螺帽HOT DIP GALVANIZING BOLTS AND NUTS机械镀MECHANICAL GALVANIZED迷你成型机MINI-FORMERS成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机PARTS FORMING MACHING冲模PUNCH DIES冲子PUNCH PINS罗拉成型机ROLLERS FORMERS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE止付螺丝成型机SET SCREWS FORMERS套高成型机SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热处理炉SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机TAPPING MACHINE螺丝攻、车刀、模具TAPS DIES AND TOOLS搓牙机铁屑分离装置THREAD CHIP SEPARATOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化钨模具TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务TiN HARD COATING FOR CUTTING TOOLS AND PUNCHBY PVD电镀化学原料VARIOUS ELECTROPLATING CHEMICALS环规校正CALIBRATION FOR RING GAGE环规、牙规、三线规校正CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIREGAGE螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTSFORMERS螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE德国SCHATZ扭力机代理REPRESENTATIVE OF SCHATZ TORQUE MACHINISO品质保证系统ISO QUALITY ASSURANCE SYSTEM生产管理系统PRODUCTION CONTROL SYSTEM物料管理系统MATERIAL CONTROL SYSTEM齿轮GEARS不锈钢牙条棒STAINLESS STEEL HREAD ROD马达轴承轴心组件BEARING SHAFT(MOTOR)轴承轴心BEARING SHAFT开口铆钉BLIND RIVETS长形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉钉BLIND RIVETS实心梢CLEVIS PINS AND STRAIGHT PINS弹片CLIPS卷钉COIL NAILS冷锻零件COLD FORMING PART开口销COTTER PINSE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS鸡眼钉EYELETS RIVETSR型销SNAP PINS闸、锁LATCHES AND KEEPER ASSEMBLEDS其它特殊铆钉OTHER SPECIL RIVETS销PINS格式管夹、管束PIPE HANGER铆钉RIVETS螺旋锔及螺旋圈SCREW HOOK AND SCREW RINGS中空钉SEMI-TUBULAR RIVET开叉钉SPLIT DRIVE ANCHORS弹簧华司SPRING WASHERS弹簧蝴蝶夹SPRING WINGS不锈钢华司STAINLESSSTEEL WASHERS钢铁钉STEEL AND IRON NAILS搓牙铁钉THREAD NAILS钛合金铆钉TITAIUM ALLOY RIVETS管形铆钉TUBULAR RIVETS华司WASHERS真空热处理VACUUM HEAT TREATMENT螺丝、螺帽、五金、DIY扣件FASTENERS合金钢工具ALLOY STEEL TOOLS螺栓模BOLT HEADING DIES手动拉钉钳HAND RIVETER船舶链ANCHOR CHAIN脚踏车链锁BICYCLE CHAIN LOCKS螺丝起子BIT罗拉CHAIN ROLLER特殊铆合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链DECORATIVE CHAINS自攻螺纹衬套ENSAT THREADED INSERTS六角扳手HEXAGON KEYS超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTIONMOULDEINGS汽车特殊杆接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS 螺纹护套RECOIL INSERTS链条用滚子ROLLER FOR ROLLER CHAIN金属板镶嵌组件及自动夹扣组件SHEET METAL FASTENERS工具套筒组件SOCKET WRENCH SETS不锈钢链STAINLESS STEEL CHAINS轭子T-YOKE轮胎链TIRE CHAINS 狗链DOG CHAINS喇叭头轭铁U-YOKE,T-YOKE FOR SPEAKER不锈钢输送带轮用轨道STAINLESS WHEEL'S RACK FOR TRANSPORTER工业用链INDUSTRIAL STEEL LINK CHAINS拖链安全链TOW CHAINS AND SAFETY CHAINS机车离合器零件MANUFACTURE OF MOTORCYCLE'S CVT PARTS牙条棒THREAD ROD2006-7-22 17:25 xuzhengyu4、焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬Normteile标准件Gewinde, Schrauben, Muttern螺纹、螺栓、螺母Gewinde螺纹Schrauben螺栓Gewindeauslufe螺纹收尾、肩距Gewindefreistiche螺纹退刀槽Senkungen锪孔、沉孔Mutter螺母Scheibe档圈Schlüsselweite扳手口尺寸Werkzeugvierkante工具四方柄Stifte, Bolzen, Niete, MitnehmerverbindungStifte 圆柱销Kerbstifte弹性销Bolzen轴销Keile 键Federn弹簧Keilwellenverbindung花键连接Blindniete抽芯铆钉Werkzeugkegel刀具、工具锥度Normteile für Vorrichtungen und Standzwerkzeuge工装夹具和冲裁模具的标准件Normteile für Vorrichtungen工装夹具的标准件T-NutenT型槽Kugelscheiben球面垫圈Normteile für Stanzwerkzeuge冲裁模具标准件Federn弹簧Antriebstechnik传动技术RiementriebeV型带传动Gleitlagerbuchsen滑动轴承轴瓦W?lzlager滚动轴承Nutmuttern圆螺母Passscheiben配合垫圈Stützscheiben调整垫圈Wellenenden轴端Wellendichtring轴用密封件RunddichtringO型密封圈机械工具Mechanic“s Toolsspanner 扳子(美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子(美作:socket wrench)calipers 卡规pincers, tongs 夹钳shears 剪子wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯rivet 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈staple U形钉grease gun 注油枪oil can 油壶jack 工作服机械加工抛光polishing安装to assemble扳手wrench半机械化semi-mechanization; semi-mechanized半自动滚刀磨床semi-automatic hob grinder半自动化semi-automation; semi-automatic备件spare parts边刨床side planer变速箱transmission gear柄轴arbor部件units; assembly parts插床slotting machine拆卸to disassemble超高速内圆磨床ultra-high-speed internal grinder车床lathe; turning lathe车刀lathe tool车轮车床car wheel lathe车削turning车轴axle衬套bushing 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Qu ick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手幕墙行业英语a.含沥青的Copper n.铜Bituminous paint 沥青油Cracked a.开裂的Board n.板Criteria n.标准，要点Bolt n.螺栓Critical a.危险的，临界的Bond v.接合,搭接Curtain wall 幕墙Bonding n.搭接,接合Curved a.弯曲的Booklet n.小册子DBottom n.底部Data n.数据Bracket n.支托Dead load 恒荷载Buckle vi.使弯曲,使屈服Deduction n.折减，扣除Built-up a.有组织的,密集的Definition n.定义，精确度C Deflection n.挠度C/C =center to center Deform v.变形Canopy n.天蓬,雨蓬Deformation n.变形幕墙常用英语Diagonal 对角线FDensity n.容重，密度Fabricate v.加工Depth n.深度Fabrication n.加工Derivation n.引出，导出Facial(façade) a.脸部的，表面的Description n.描述Facial glass (façade glass) 面玻璃Design n.设计Fatigue n.v.疲劳Detail n.详图Feature 装饰物，特征Detection n.探知，发现Figured glass 压花玻璃Development n.发展Fillet n.带子，带形的Die n.冲模Fin n.鳍，鳍状物Difference n.不同，差异Fin glass (stiffen fin glass) 肋玻璃Dimension n.尺寸Finish n.完成，装饰Direct a.ad.直接的，v.指挥Finished floor level =F.F.LDistance n.距离Fire prevention 防火Distributed a.均匀的，分布的Fix v.固定Double glazing 双层（中空）玻璃Fixing lug n.摩耳Downward a.向下的Flange n.凸缘，翼缘Downwind a.顺风面Flashing n.防水板，遮雨板Drive pin 射钉Float glass 浮法玻璃Dynamic a.活动的，动态的Folded 折叠的，拦杆Derivation n.引出，导出Force n.力，力量；v.强迫Description n.描述Foreword n.序言Design n.设计Formula n.方程Detail n.详图Free stand type 坐（落）地式Detection n.探知，发现Function n.函数Development n.发展Fixing lug n.摩耳Die n.冲模Flange n.凸缘，翼缘Difference n.不同，差异Flashing n.防水板，遮雨板E Float glass 浮法玻璃Earthquake n.地震Folded 折叠的，拦杆Earthquake load 地震荷载Force n.力，力量；v.强迫Eccentric a.偏心的Foreword n.序言Eccentrically Adv.偏心地Formula n.方程Effect v.影响GEffective a.有效的G.M.S. =galvanized mild steelElastic a.弹性的Galvanization n.镀锌Elevation n.海拨，立面Galvanize v.镀锌Engineering n.工程Glass n.玻璃Equal angle a.等边角钢Glazing n.玻璃窗，玻璃装饰Equivalent a.等于Global a.通用的,全球的,球形的Examined 审定Granite cladding 花岗岩围护，干挂石Example n.例子，样本Gravity n.重量Exposed frame a.明框Grille n.格子Exterior a.外部的Grout n.水泥浆Extrusion n.挤压Grouting （填塞的）水泥砂浆幕墙常用英语Gustn.阵风Minimum n.最小值Gutter n.天沟，排水沟Modulus n.模量Gyration n.回转，旋转Moment n.瞬间，矩H Movement capacity 变形能力Hanger system 吊挂系统Mullion n.竖框，竖料Hardware n.五金NHeight n.高度Natural a.n.自然的，Hidden frame 隐框Negative a.n.否定，负数Horizontal a.水平的Neutral a.中性的Hot-dipped zinc Galvan 热浸锌Normal a.普通的，法向的I Nos. =numbersImmediate a.当地的Nut n.坚果，螺丝帽Include v.包括PIncrease V.增加Panel n.板，仪表板Individual a.个别的Parallel a.n.v.平行Inertia n.惯性Part n.部分，局部Inertia moment 惯性矩Partial a.部分的Interior a.内部的Peak 峰值Investigate n.调查,研究Penetration n.浸透，浸入Issue n.v.发行，发布Penetration butt 对接埋入焊Imposed a.应用的，利用的Period a.句号，周期J Permissible a.允许的Joint n.连接Permit v.允许Joist n.托梁，桁Pile n.桩L Pin n.a.大头钉，栓Laminated glass 夹层玻璃Plan n.计划,平面图,设计图Lateral a.侧面的，旁边的Plastic a..塑性的，可塑的Length n.长度Plate n.盘子，金属板Linear a.线性的Podium n.矮墙，女儿墙Lips n.薄片，唇Poisson’s Ratio 泊桑比Load n.v.荷载，加载Polished glass 磨光玻璃Local a.局部的，地方性的Pre-cast 预埋，预置Long a.长的Preliminary a.初步的Louver n.百叶，百页Pressure n.v.压力，压强Lug n.耳朵Principal a.主要的M Property n.财产，性质，属性M.S.. =mild steel Purposed v.计划，打算Manufacturer n.制造高，厂商Protect v.保护Material n.材料Purpose n.目的，企图，论题Maximize v.最大化PVF2 Coating 氟碳喷涂Maximum n.最大值practice n.实行Member n.杆件QMetal n.金属Quantity n.量，数量，总数Micron n.微米RMinimize v.最小化Railing n.扶手，拦杆幕墙常用英语Ratio n.比，比率SpacingReaction n.反应，反作用Suffer Rebar =reinforce bar Stud Rectangle hollow section 矩形管Structure n.结构Reduce v.减少，缩小Structure floor level =S.F.LRefer v.提交，查阅Strut n.支柱Reference n.v.参考，引用Sub-contractor n.分包商Reflective glass 反射玻璃Submission n.递呈,提交,服从Reinforcement n.加强件，加固物Suction n.吸力Resistance v.抵抗Super-structure 主体结构Restrain n.约束Supplier n.供应商Result n.结果Supply n.v.提供，补充，替代Revision n.修订，校订Support n.v.支撑，支持RHS =rectangle hollow section Support on four sides 四边支撑Rod n.小枝，竿Support on two sides 两边支撑Roof n.屋顶Surface n.表面Rigidity n.刚性Symmetry a.对称的S TScope n.范围，广度Technical a..技术的，工业的Screw n.v.螺钉，螺旋桨，拧紧Tee n.T 字形，T形物Sealant n.密封胶Temperature n.温度Self-weight 自重Tempered a.调节的，钢化的Serial n.序列，系列Tempered glass 钢化玻璃Setting block 垫块Temporary a.临时的Shape n.v.形状，定形Tensile a.拉力的，张力的Shear n.v.修剪，剪切Tension n.v.张力，拉力SHS =square hollow section Terrain n.地带，地域，范围Silicone n.硅树脂The arm of force 力臂Similar n.a.相似的，相同Thickness n.厚度Simply supported beam 简支梁Thread n.纤维Site-ground 室外地面Tile 砖，磁片Sleeve n.袖子，套筒Tinted 染色的Slope n.v.倾斜Title n.名称，标题Span n.跨度Tolerance n.宽容，公差Specification n.规格，详述Top n.顶部，上总的Spider fixing （玻璃）固定爪Torsion n.扭转，扭矩Splice Vt.n.接合,连接,结婚Total 总的，总数Square hollow section 方形管Transom n.横梁，横档Stability n.稳定性Trapezoid n.梯形，不等边四边形Stainless steel 不锈钢Triangle n.三角形Standard n.标准Type 类型，型号，打字Stiffen v.使变硬UStrength n.强度UB =universal beamStress n.压力，应力UDL =uniformly distributed loadStructural a.结构的Unequal angle n.不等边角钢幕墙常用英语Uniformly Adv.统一的，一律的Universal beam 通用梁Universal column 通用柱幕墙常用英语ACantilever beam悬臂梁Accessories附件Capacityn.能力,容量According to根据Captionn.说明,标题Acida.酸，酸性的Cast-in埋入Acrossad.prep.横过，交叉Cataloguen.目录,总目Allowable允许Cementn.水泥Alloy合金CertificateVt.n.证明,证明书Aluminum铝，铝材Channeln.槽,频道，通道Analysisn.分析Checkv.检查，查阅Analyze (analyse)v.分析Circular hollow sectionn.圆通Anchor锚固Claddingn.围护Angle steel角钢Clear glass透明玻璃Annealed glass退火玻璃Clientn.客户，委托人Anodizingn.阳化Coden.代码，法规Anti-corrosive zinc paint防锈白漆Coefficientn.系数Appendix附录Columnn.柱Approval承认,审批Combineda.组合Architectn.建筑师Comparisonn.比较Architecturen.建筑Completev.完成Artificiala.人造的,虚假的Compositea.n.混合物，混合Assumev.假设Compressionn.压，压迫Assumptionn.假设compressivea.受压的Average=AVG. 平均Concreten.混凝土Axiala.轴向的Conditionn.条件Axisn.轴向的Considerv.认为BConstantn.常数Backer rod加强棒,泡沫棒Contactn.a.接触Base level基本平面,海平面Contact surfacen.接触面Be equivalent to等于Contentn.内容Bear负荷Continuous beam连续梁Bendv.n.弯曲,屈服Contractorn.承包商Bituminousa.含沥青的Coppern.铜Bituminous paint沥青油Crackeda.开裂的Boardn.板Criterian.标准，要点Boltn.螺栓Criticala.危险的，临界的Bondv.接合,搭接Curtain wall幕墙Bondingn.搭接,接合Curveda.弯曲的Bookletn.小册子DBottomn.底部Datan.数据Bracketn.支托Dead load恒荷载Bucklevi.使弯曲,使屈服Deductionn.折减，扣除Built-upa.有组织的,密集的Definitionn.定义，精确度CDeflectionn.挠度C/C=center to centerDeformv.变形Canopyn.天蓬,雨蓬Deformationn.变形幕墙常用英语Diagonal对角线FDensityn.容重，密度Fabricatev.加工Depthn.深度Fabricationn.加工Derivationn.引出，导出Facial(fa[$ccedil]ade)a.脸部的，表面的Descriptionn.描述Facial glass (fa[$ccedil]ade glass)面玻璃Designn.设计Fatiguen.v.疲劳Detailn.详图Feature装饰物，特征Detectionn.探知，发现Figured glass压花玻璃Developmentn.发展Filletn.带子，带形的Dien.冲模Finn.鳍，鳍状物Differencen.不同，差异Fin glass (stiffen fin glass)肋玻璃Dimensionn.尺寸Finishn.完成，装饰Directa.ad.直接的，v.指挥Finished floor level=F.F.L Distancen.距离Fire prevention防火Distributeda.均匀的，分布的Fixv.固定Double glazing双层（中空）玻璃Fixing lugn.摩耳Downwarda.向下的Flangen.凸缘，翼缘Downwinda.顺风面Flashingn.防水板，遮雨板Drive pin射钉Float glass浮法玻璃Dynamica.活动的，动态的Folded折叠的，拦杆Derivationn.引出，导出Forcen.力，力量；v.强迫Descriptionn.描述Forewordn.序言Designn.设计Formulan.方程Detailn.详图Free stand type坐（落）地式Detectionn.探知，发现Functionn.函数Developmentn.发展Fixing lugn.摩耳Dien.冲模Flangen.凸缘，翼缘Differencen.不同，差异Flashingn.防水板，遮雨板EFloat glass浮法玻璃Earthquaken.地震Folded折叠的，拦杆Earthquake load地震荷载Forcen.力，力量；v.强迫Eccentrica.偏心的Forewordn.序言EccentricallyAdv.偏心地Formulan.方程Effectv.影响GEffectivea.有效的G.M.S.=galvanized mild steel Elastica.弹性的Galvanizationn.镀锌Elevationn.海拨，立面Galvanizev.镀锌Engineeringn.工程Glassn.玻璃Equal anglea.等边角钢Glazingn.玻璃窗，玻璃装饰Equivalenta.等于Globala.通用的,全球的,球形的Examined审定Granite cladding花岗岩围护，干挂石Examplen.例子，样本Gravityn.重量Exposed framea.明框Grillen.格子Exteriora.外部的Groutn.水泥浆Extrusionn.挤压Grouting（填塞的）水泥砂浆幕墙常用英语Gustn.阵风Minimumn.最小值Guttern.天沟，排水沟Modulusn.模量Gyrationn.回转，旋转Momentn.瞬间，矩HMovement capacity变形能力Hanger system吊挂系统Mullionn.竖框，竖料Hardwaren.五金NHeightn.高度Naturala.n.自然的，Hidden frame隐框Negativea.n.否定，负数Horizontala.水平的Neutrala.中性的Hot-dipped zinc galvan热浸锌Normala.普通的，法向的INos.=numbersImmediatea.当地的Nutn.坚果，螺丝帽Includev.包括PIncreaseV.增加Paneln.板，仪表板Individuala.个别的Parallela.n.v.平行Inertian.惯性Partn.部分，局部Inertia moment惯性矩Partiala.部分的Interiora.内部的Peak峰值Investigaten.调查,研究Penetrationn.浸透，浸入Issuen.v.发行，发布Penetration butt对接埋入焊Imposeda.应用的，利用的Perioda.句号，周期JPermissiblea.允许的Jointn.连接Permitv.允许Joistn.托梁，桁Pilen.桩LPinn.a.大头钉，栓Laminated glass夹层玻璃Plann.计划,平面图,设计图Laterala.侧面的，旁边的Plastica..塑性的，可塑的Lengthn.长度Platen.盘子，金属板Lineara.线性的Podiumn.矮墙，女儿墙Lipsn.薄片，唇Poisson’s Ratio泊桑比Loadn.v.荷载，加载Polished glass磨光玻璃Locala.局部的，地方性的Pre-cast预埋，预置Longa.长的Preliminarya.初步的Louvern.百叶，百页Pressuren.v.压力，压强Lugn.耳朵Principala.主要的MPropertyn.财产，性质，属性M.S..=mild steelPurposedv.计划，打算Manufacturern.制造高，厂商Protectv.保护Materialn.材料Purposen.目的，企图，论题Maximizev.最大化PVF2 Coating氟碳喷涂Maximumn.最大值practisen.实行Membern.杆件QMetaln.金属Quantityn.量，数量，总数Micronn.微米RMinimizev.最小化Railingn.扶手，拦杆幕墙常用英语Ration.比，比率SpacingReactionn.反应，反作用SufferRebar=reinforce barStudRectangle hollow section矩形管Structuren.结构Reducev.减少，缩小Structure floor level=S.F.LReferv.提交，查阅Strutn.支柱Referencen.v.参考，引用Sub-contractorn.分包商Reflective glass反射玻璃Submissionn.递呈,提交,服从Reinforcementn.加强件，加固物Suctionn.吸力Resistancev.抵抗Super-structure主体结构Restrainn.约束Suppliern.供应商Resultn.结果Supplyn.v.提供，补充，替代Revisionn.修订，校订Supportn.v.支撑，支持RHS=rectangle hollow sectionSupport on four sides四边支撑Rodn.小枝，竿Support on two sides两边支撑Roofn.屋顶Surfacen.表面Rigidityn.刚性Symmetrya.对称的STScopen.范围，广度Technicala..技术的，工业的Screwn.v.螺钉，螺旋浆，拧紧Teen.T字形，T形物Sealantn.密封胶Temperaturen.温度Self-weight自重Tempereda.调节的，钢化的Serialn.序列，系列Tempered glass钢化玻璃Setting block垫块Temporarya.临时的Shapen.v.形状，定形Tensilea.拉力的，张力的Shearn.v.修剪，剪切Tensionn.v.张力，拉力SHS=square hollow sectionTerrainn.地带，地域，范围Siliconen.硅树酯The arm of force力臂Similarn.a.相似的，相同Thicknessn.厚度Simply supported beam简支梁Threadn.纤维Site-ground室外地面Tile砖，磁片Sleeven.袖子，套筒Tinted染色的Slopen.v.倾斜Titlen.名称，标题Spann.跨度Tolerancen.宽容，公差Specificationn.规格，详述Topn.顶部，上总的Spider fixing（玻璃）固定爪Torsionn.扭转，扭矩SpliceVt.n.接合,连接,结婚Total总的，总数Square hollow section方形管Transomn.横梁，横档Stabilityn.稳定性Trapezoidn.梯形，不等边四边形Stainless steel不锈钢Trianglen.三角形Standardn.标准Type类型，型号，打字Stiffenv.使变硬UStrengthn.强度UB=universal beamStressn.压力，应力UDL=uniformly distributed load Structurala.结构的Unequal anglen.不等边角钢幕墙常用英语UniformlyAdv.统一的，一律的Universal beam通用梁Universal column通用柱Unsymmetrical不对称Upwarda.向上的Upwind迎风面VVariablen.变量Varyv.变化，改变Velocityn.速度，速度。

中英对照表Air Infiltration ：气密性Air Space：空间Alloy：合金Alum Foil：铝薄片Alum.Casting Cam Handle：铝合金拉手Alum.Cladding：铝合金板Alum.Handle：铝合金窗手制Aluminium：铝合金Anchor(Bolt or plate)：锚件（螺栓或板）Assembly：装嵌Back Elevation：后立面Back Pane：背板Backer Rod：聚脂塑料填塞棒（小圆棒）Baffle：挡板/隔气流物料Balustrade：栏杆Bearing Roller：滚轴辘Bent Sheet：摺曲板Bitumen：沥青Black Anodized：黑色电镀Bond Breaker Tape：阻隔粘合胶纸Box Section：通Bracket：码件Bronze Anodized：古深电镀Bronze Tinted Glass：茶色玻璃Bulb Gasket：空心管形胶条Butt Joint：对接Buttet：涂抹Cam Handle：窗手制Canopy：雨篷Cast Wired Glass：镶丝玻璃（铁线玻璃）Casting：铸造Caulking：填缝Ceiling：天花/吊顶Ceramic Frit：陶瓷制玻璃原料Channel：槽Cladding：包板Clear Float Glass：浮法玻璃Clip：夹Components：配件Cencrete：混凝土Coping：压顶Corner Mullion：转角企柱Curb：路线Galvanized：镀铅水Galvanizer Mild Steel：镀铅水铁件Gasket：胶条Glass：玻璃Glass Fin：加力玻璃条Glazing Adaptor：镶玻璃承接件Glazing Bead：玻璃压条/玻璃线Gondola：吊船Gusset Plate：角撑板Guttet：水槽Gypsum Board：石膏板Halfen Channel：槽形预埋件Handle：拉手/把手Handrail：扶手Hardware：小五金/零件Head：顶Heat Strengthened：热钢化Height/High：高度Hex Head：六角头Hex Phillips Head：六角十字头Hinge：铰Hollow：通Horizontal：横向Hot Dip Galvanizing：热浸镀铅水I-Beam(Steel)：工字铁Imbed(Embed)：预埋件In Board Lite：内层片Inside：内Insulating Glass：双层中空玻璃Insulation：隔热棉Interior：内面Isolator Tape：隔断胶纸Jamb 边企Keepet：锁扣件Kicking Plate：踢脚板Knob Lock：球拗门锁Laminated Galss：夹层安全玻璃Length/Long：长度Limit Device：开关限制撑Location：位置Louvre：百叶窗M12S/S Bolt And Nut With Washer：M12不锈钢螺丝及螺母Machine Screw：机丝Main Contractor：建筑/施工单位Mastic Pointing：胶合材料/胶合补料Mill Finish：原来表面（不加处理之表面）Mirror Finish：磨光镜面Module：模数（选定尺寸）Mohair Weather Strip：防风雨毛压条Mould ：模具Mullion：企挂Multi-Point Locking Device：多点式锁制Natural Anodized：原色电镀Neoprene氯丁橡胶Norton Tape：诺顿塑胶密封条Notch：缺口Nut：螺丝母Nyiock Nut：尼龙锁紧螺帽/防松螺帽Nyatron：一种尼龙的学名Obscured Glass：朦玻璃Obscured Wired Glass：夹丝（铁线）朦玻璃Opacifier：遮光物料Openable Window：开启窗Out Board Lite：外层片Outside：外Pan Head：扁圆头/盘形Parapet Wall or Parapet：女儿墙Pelmet：窗帘/匣子Phillips Head：十字头Plan ：平面Plaster：批灰Plaster Stop：批灰收口料Ployethylene Foam：聚乙烯发泡Plywood：夹板Polished Wired Glass：磨光铁线玻璃Polyvinyl Chloride：聚氯乙烯Pop-Rivet：拉钉Pre-Cast Imbed：预埋件Pressure Bar/Bead：压巴Primer：底油Pull-Out：拉出Pvc Isolate Tape：PVC隔绝胶纸Quantity：数量Ready Concrete：混凝土Rear Elevation：后立面Reflective Glass：反射玻璃/反光玻璃Reinforcement：加劲材料Remark：备注Rivet：拉钉Rod：圆枝Roll Pin：卷针Round Window：弦窗S/S Flat Head Machine Screw：不锈钢平头机丝S/S Project Handle：不锈钢窗较Santoprene Gasket：高级橡胶条Sash：活动开启窗Section：切面Self Tapping Screw：自动刻螺丝纹螺丝Serrated：锯齿状Setting Block：垫块Shear：剪力Sheet Metal Screw：钢牙螺丝Shim：垫片Shimming Block：填隙垫Shimming Plate：垫位Side Elevation：侧立面Side Hung：掩窗Silicone Sealant：硅胶/硅硐密封胶Silicone Splice：硅硐胶接件Sill：底Sill Board：窗台板Sillcone Sealant：矽质封胶Skylight：采光天窗/天棚Slab：楼板Sleeve：套筒/套蕊Sliding Door/Window：横拉门/窗Slot Hole：长孔Slotted Head：槽头Solid Bar：扁巴Space Frame：三角钢架Spandrel：上下层窗空间/腰板Spandrel Glass：腰板玻璃Spanner Operated：用板手操作Splice：拼接Sponge：海棉Spring Lock Washer：弹弓锁介子Stainless Steel：不锈钢Stiffener：加劲材料Stool：窗台找平边Structural Floor Level：地台标志Structural Glazing：结构隐框Structural Opening：洞口尺寸Suspension System：悬吊式系统Tack weld：平头焊接Tead Wood Board：木窗台板Tempered Glass：强化/钢化玻璃Thermal：熟能Thick：厚Tie Back：牵索Tie Wire：捆绑线/绳Top Hung Window：窗Top Pivot：门顶较Transom：横料Transom Cover：横料盖Truss Head ：扁头Typhoon Bolt/Lock：防风锁Vent：活动窗Vert. Or Hori. Slot Hole：竖向或横向长孔Vertical竖向Vinyl：PVC胶Vinyl Weather Strip：防风雨胶压条Vision or Vision Surface：见光部份Washer：介子Water Bar：隔水巴Water Drip：滴水线Water Penetration：水密性Waterproofing Cement Grouting：防水水泥沙浆Waterproofing Compound：防水剂Weather Strip：防风雨压条Wedge：楔形物Weep Hole：泌水孔Weep Hole Cover：泌水孔盖Welding：烧焊Width/Wide：阔度Window Dimension：窗框尺寸Window Mark：窗号Wood Screw：木牙螺丝Woolen Pile：毛条Wired Glass：钢丝玻璃片Zinc Coating：镀锌STIFFINER FRAME：框架INSULATION：绝缘材料NEOPRENE GASKET：氯丁橡胶密封垫ADHESSIONN TAPE：胶带ACCESS HOLE WITH PLUG：带楔形的通孔SILICONE SEALNT：硅酮涂胶REFLECTIVE TEMPERED GLASS：镀膜钢化玻璃WEATHER GASKET：挡风雨密封垫DOW MUL TI-SEAL：硅酸胶DIA A/S BOLT W/NUT & WASHER：螺栓螺帽及垫圈G．M．S．BTACKET：托架ISOLATION PVCPLATE：氯乙烯隔离板SPNDREL GLASS：窗上玻璃M．S．ANGLE：铁码G．M．S．JOIST MULLION：工字铁CLEAR FLOOT GLASS；反光玻璃SOUARE TUBETRANSOM：面通TRANSOM：横料MULLION：企料TYPICAL ANCHOR PLATE：锚板（Bracket）码件Concrete Fixing Pin：混凝土固定件EMBED：预埋件Waterproof membrane：防水皮Boundary Line：简称B L边界线INV：反梁。

门窗、幕墙常用语中英文对照幕墙英语词汇A-Z4mm THK. Composite Aluminum P lastic 4mm厚复合铝板5mm THK. Aluminum Plate 5mm厚单铝板Accessories 附件According to 根据Acid 酸，酸性的Across 横过，交叉Allowable 允许Alloy 合金Alum bracket 铝支架Alum. Panel 铝板Aluminum alloy 铝合金Aluminum 铝，铝材Analysis 分析Anchor Bolt 锚拴Anchor 锚固Angle steel 角钢Annealed glass 退火玻璃Anodizing oxidation coating 阳极氧化喷涂Anodizing 阳化Anti-corrosive zinc paint 防锈白漆Anti-reflective coating 防反射涂膜Appendix 附录Approval 承认,审批Architect 建筑师Architecture 建筑Artificial 人造的,虚假的Assume 假设Assumption 假设Average=AVG. 平均Aviation obstruction 阻航Axial 轴向的Axis 轴向的Backer rod 加强棒,泡沫棒Base level 基本平面,海平面Be equivalent to 等于bead 压条Bear 负荷bedding 衬垫Bend 弯曲,屈服Bituminous paint 沥青油Bituminous 含沥青的Board 板Bolt 螺栓Bond 接合,搭接Bonding 搭接,接合Booklet 小册子Bottom 底部Brace 斜撑Bracket 支托Buckle 使弯曲,使屈服Built-up 有组织的,密集的Butt weld 对接焊缝Canopy 天蓬,雨蓬Cantilever beam 悬臂梁Caption 说明,标题Cast-in 埋入Catalogue 目录,总目Cement 水泥Cement 水泥Cementations 水泥的Certificate 证明,证明书Channel 槽,频道，通道Check 检查，查阅Circular hollow section 圆通Clear glass 透明玻璃Client 客户，委托人Closure 外盖Code 代码，法规Coefficient 系数Column 柱Combined 组合Comparison 比较Complete 完成Composite 混合物，混合Compression 压，压迫Compressive 受压的Concealed 隐藏的Concrete 混凝土Condition 条件Consider 认为Constant 常数Construction tolerance 施工容差Contact surface 接触面Contact 接触Content 内容Continuous beam 连续梁Contractor 承包商Copper 铜Court 中庭Cracked 开裂的Criteria 标准，要点Critical 危险的，临界的Crylic acid coating 丙烯酸喷涂Curtain wall 幕墙Curved 弯曲的Data 数据Dead load 恒荷载Deduction 折减，扣除Definition 定义，精确度Deflection 挠度Deform 变形Deformation 变形Demountable panel 可拆除挂板Density 密度Density 容重，密度Depth.深度Derivation 引出，导出Description 描述Design 设计Detail 详图，节点图Detection 探知，发现Development 发展Diagonal 对角线Diagrid 斜交格构Diaphragm 加强层Die 冲模Difference 不同，差异Dimension 尺寸Direct 直接的Distance 距离Distributed 均匀的，分布的Double glazing 双层（中空）玻璃Double Skin Wall 双层幕墙Downward 向下的Downwind 顺风面Drive pin 射钉Dynamic 活动的，动态的Earthquake load 地震荷载Earthquake 地震Eccentric 偏心的Effect 影响Effective 有效的Egress door 紧急出口Elastic 弹性的Electrophoretic coating 电泳喷涂Element 构件Elevation 立面Embedment 预埋件Engineering 工程Equal angle 等边角钢Equivalent 等于Examined 审定Example 例子，样本Expansible 伸缩的Expansion Bolt 膨胀螺栓exposed frame curtain wall 明框幕墙Exposed frame 明框Exterior 外部的Extrusion 挤压Fabricate 加工Fabrication 加工Facial glass (facade glass) 面玻璃Fastener-Stainless Steel 不锈钢紧固件Fatigue 疲劳Feature 特征Figured glass 压花玻璃Fillet 带子，带形的Fin glass (stiffen fin glass) 肋玻璃Fin 鳍，鳍状物Finish 完成，装饰Fire prevention 防火Fire Stop mineral wool 防火岩棉Fix 固定Flange 凸缘，翼缘Flashing 防水板，遮雨板Float glass 浮法玻璃Foam Rod 泡沫填充棒Folded 折叠的Force 力Foreword 序言Formula 方程Free stand type 坐（落）地式full glass curtain wall 全玻幕墙Function 函数Galvanization 镀锌Galvanize 镀锌Galvanized Bolt 镀锌螺栓Gasket 胶条Geometry 几何定位，定位（图）Glass curtain wall 玻璃幕墙Glass 玻璃Glazing 玻璃窗，玻璃装饰Global 通用的,全球的,球形的Granite cladding 花岗岩围护，干挂石Granite 花岗石Gravity 重量Grille 格子,隔栅Grout 水泥浆Grouting （填塞的）水泥砂浆Gutter 天沟，排水沟Gyration 回转，旋转Half strengthened glass 半钢化玻璃Hanger system 吊挂系统Hardware 五金Heat Soak Test 引爆处理Height 高度Hidden frame curtain wall 隐框幕墙Hidden frame 隐框Horizontal 水平的Hot-dipped zinc galvanization 热浸锌Immediate 立即的Imposed 应用的，施加的Inclined 倾斜的Include 包括Increase 增加Individual 个别的Inertia moment 惯性矩Inertia 惯性Insulating Glass Unit (IGU) 中空玻璃Interior 内部的In tumescent coating 防火涂层Investigate 调查,研究Issue 发行，发布Joint 连接Joist 托梁，Laminated glass 夹层玻璃Laminated glass 夹胶玻璃Lateral 侧面的，旁边的Length 长度Linear 线性的Lip 薄片Load 荷载，加载Lobby 大厅Local 局部的，地方性的location blocks 定位块Long 长的Louver 百叶，百页Lug 凸耳，凸杆Machine Bolt 机制螺栓Main structure主体结构Manufacturer 制造高，厂商Material 材料Maximize 最大化Maximum 最大值Member.杆件Membrane 防水层Mesh 网，网状物Metal 金属Metallic 金属的Micron 微米Minimize 最小化Minimum 最小值Mock-up 实体样板Modulus 模量Moment 力矩Monumental glazing 巨幅玻璃Movement capacity 变形能力Mullion 竖框，竖料Natural 自然的，Negative 否定，负数Neutral 中性的Node 节点Normal 普通的，法向的Nut 螺丝帽Operable panel 可开启面板Panel 板，仪表板Parallel 平行Part 部分，局部Partial 部分的Patio 内庭Peak 峰值Penetration butt 对接埋入焊Penetration 浸透，浸入Period 句号，周期Permissible 允许的Permit 允许Pile 桩Pin 大头钉，栓Plan 计划,平面图,设计图Plastic 塑性的，可塑的Plate 金属板Plinth 基座Podium 矮墙，女儿墙Poisson’s Ratio 泊桑比Polished glass 磨光玻璃Powder coating 粉末喷涂Practice 实行Pre-cast 预埋，预置Preliminary 初步的Pressure 压力，压强Principal 主要的Protect 保护Purpose 目的，企图，论题Purposed 计划的，打算的PVDF Coating 氟碳喷涂Quantity 量，数量，总数Railing 扶手，栏杆Ratio 比，比率Reaction 反应，反作用Rectangle hollow section 矩形管Reduce 减少，缩小Refer 提交，查阅Reference 参考，引用Reflective glass 反射玻璃Reinforcement 加强件，加固物Relative Heat Gain 相对热增益Relief pattern 浮雕图案Resistance 抵抗Restrain 约束Result 结果Revision 修订，校订Revolving panel 旋转面板Rigid Insulation 刚性绝缘体Rigidity 刚性Rod 棒，竿Roof 屋顶Scope 范围，广度Screw 螺钉，拧紧Seal 密封Sealant 密封胶Security configuration 保安配置Self-weight 自重semi-exposed framing glass curta in wall 半隐框幕墙Serial 序列，系列Setting block 垫块setting blocks 支承块Shading coefficient 遮阳系数Shaft 管井Shape 形状，定形Shear force 剪力Shear 修剪，剪切Sheet 薄板Similar 相似的，相同Simply supported beam 简支梁Single toughened glass 单层钢化玻璃Site-ground 室外地面Skylight 天窗Slab 楼板Sleeve 袖子，套筒Slope 倾斜Sloped 倾斜的Snow and ice retention 雨雪拦截设施Span 跨度Spandrel 横档Specification 规格，详述Spider fixing （玻璃）固定爪Splice 接合,连接Square hollow section 方形管Stability 稳定性Stainless steel 不锈钢Standard 标准Stiffen 使变硬Strength 强度Stress 压力，应力Structural silicone 结构硅胶Strut 支柱Sub-contractor 分包商Submission 递呈,提交,服从Suction 吸力Sunshade 遮阳Supplier 供应商Supply 提供，补充，替代Support on four sides 四边支撑Support on two sides 两边支撑Support 支撑，支持Surface 表面Symmetry 对称的Technical 技术的，工业的Temperature 温度Tempered glass 钢化玻璃Tempered 调节的，钢化的Temporary 临时的Tensile 拉力的，张力的Tension 张力，拉力Terrain 地带，地域，范围The arm of force 力臂Thickness 厚度Tile 砖，磁片Tinted 着色的Title 名称，标题Tolerance 允许误差Top 顶部，上总的Torsion 扭转，扭矩Total 总的，总数Transom 横梁Transom 横梁，横档Trapezoid 梯形，不等边四边形Triangle 三角形Type 类型，型号，打字Typical 标准的Unequal angle steel 不等边角钢Unfolded 展开图U-value U-值Visible Light Reflectance 可见光反射率Visible Light Transmittance 可见光透光率Void 中空处Walkable 可上人的Weather proofing sealant 耐候胶Weep 滴水Weld 焊接Welding line 焊缝Zinc-plated 镀锌1、表面处理、热处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理2、螺丝产品名称（螺丝螺）六角螺丝(栓) HEX HEAD CAP SCREWS (HEX BOLTS)六角机械螺丝 HEX HEAD MACHINE BO LTS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝 CARRIAGE BOLTS 环首螺丝 EYE BOLTS内六角孔螺丝 HEX SOCKET CAP SCRE WS固定螺丝 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS轮壳螺栓 WHEEL BOLTS翼形螺丝 WING SCREWS自攻螺丝 SELF TAPPING SCREWS自削螺丝 THREAD CUTTING SCREWS 钻尾螺丝 SELF DRILLING SCREWS 旋入螺丝 DRIVE SCREWS机械螺丝 MACHINE SCREWS木螺丝 WOOD SCREWS家具螺丝 FURNITURE SCREWS塑板螺丝 CHIPBOARD SCREWS墙用螺丝 DRYWALL SCREWS基础螺栓 FOUNDATION BOLTSU型螺栓 U BOLTS勾头螺栓 HOOK BOLTS套挂螺丝 TOGGLE BOLTS突缘螺丝 FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS 耐候钢螺丝 CORTEN STEEL HEAVY HE X BOLTS扭矩控制螺栓 T.C.BOLTS高张力螺栓 HIGH STRENGTH BOLTS 剪力钉(焊接螺丝) WELDING STUDS 螺丝附华司组合 SCREWS AND WASHER S ASSEMBLED(SEMS)大尺寸螺栓 BIG SIZE BOLTS不锈钢小螺丝 STAINLESS STEEL SHE ET METAL SCREWS不锈钢大螺丝 STAINLESS STEEL BOL TS铜螺丝 BRASS SCREWS铝螺丝 ALUMINUM SCREWS合金钢螺丝 ALLOY STEEL SCREWS 电子螺丝 ELECTRONIC SCREWS微小精密螺丝 MICRO SCREWS塑胶螺丝 PLASTIC SCREWS复合材料用螺丝 PARTICLE BOARD SC REWS钛合金螺丝 TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PAR TS拇指螺丝 THUMB SCREWS双头牙螺丝 DOUBLE END SCREWS HAN GER BOLT车辆(汽车)螺丝、螺帽 AUTOMOTIVE F ASTENERS航太用螺丝 AEROSPACE FASTENERS 飞机特殊扣件 SOURCE CONTROL BOLT S拉栓 BLIND BOLTS面板螺丝 PANEL FASTENERS电梯螺丝 ELEVATOR BOLTS四角头固定螺丝 SQUARE SET SCREWS大头马车螺丝 STEP BOLTS单向螺丝 ONE WAY LAG SCREWS管夹螺丝 HOSE CLAMP SCREWS不锈钢固定螺丝 STAINLESS STEEL H EX SOCKET CAP SCREWS不锈钢内六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝 HINGE SCREWS货柜螺丝 CONTAINER SCREWS复合材料钻尾螺丝 BI-METAL SELF D RILLING SCREWS三角牙螺丝 TRILOBULAR THREAD SCR EWS高低牙螺丝 HIGH LOW SCREWS夹板用螺丝 PARTICLE BOARD SCREWS马桶螺丝 TOILET CLOSET BOLTS特长螺丝 SPECIAL LONGER SCREWS 建业螺丝 BUILDING FASTENERS不锈钢六角螺丝 STAINLESS STEEL H EX SOCKET CAP SCREWS其它特殊螺丝 SPECIAL SCREWS OR B OLTS不锈钢特殊螺丝 SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝） COARSE THREA D SCREWS链带螺丝 COLLATED SCREWS 水泥螺丝 CONCRETE SCREWS板模螺丝 CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZI NC ALLOY重型车螺丝 HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝 HEX SOCKET SET SC REWS复合材料用螺丝（夹板用） PARTICLE BOARD SCREWS犁壁螺丝 PLOW BOLTS机(踏)车用螺丝、轴心 SCREWS AND S HAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心 SCREWS AND SHAFT S FOR SEWING MACHING止付螺丝 SOCKET SET SCREWS不锈钢宽牙螺丝 STAINLESS STEEL C OARSE THREAD SCREWS不锈钢高低牙螺丝 STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝 STAINLESS STEEL M ACHINE SCREWS不锈钢钻尾螺丝 STAINLESS STEEL S ELF DRILLING SCREWS不锈钢自攻螺丝 STAINLESS STEEL S ELF TAPPING SCREWS不锈钢自削螺丝 STAINLESS STEEL T HREAD CUTTING SCREWS不锈钢三角牙螺丝 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS不锈钢木螺丝 STAINLESS STEEL WOO D SCREWS套挂螺栓及螺丝 TOGGLE BOLTS钛合金膨胀螺丝 TITANIUM ALLOY EX PANSION BOLTS3、螺丝产品名称(线材)中英文对照合金钢线材盘元 ALLOY STEEL WIRE ROD球状化线材 ANNEALING WIRE AND RO D黑铁丝 BLACK WIRE黄铜棒线 BRASS WIRE AND ROD磨光棒钢 BRIGHT STEEL BAR(HEX/RO UND/SQUARE)铜合金线 COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元 FREE CUTTING STEE L WIRE ROD线材 IRON OR STEEL WIRE线材盘元 IRON OR STEEL WIRE ROD 洋白铜线 NICKEL SILVER WIRE磷青铜线 PHOSPHATE BRONZE WIRE 不锈钢条棒 STAINLESS STEEL BAR(R OUND/HEX/SQUARE)不锈钢冷锻线材 STAINLESS STEEL C OLD HEADING WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢线材 STAINLESS STEEL WIRE 不锈钢线材及盘元 STAINLESS STEEL WIRE AND ROD棒钢 STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机 90讧EVOLVING W IRE TWISTING MACHINE气动拉钉机 AIR RIVETER各式螺丝类产品自动包装 AUTOMATIC PACKAGING FOR ALL KINDS OF PACK AGING自动包装机 AUTOMATIC PACKING MAC HINE螺丝制造搓牙机械 AUTOMATIC THREA D ROLLING MACHINE螺丝割尾加工机械 AUTOMATIC THREA D SLOTTING MACHINE螺丝制造成型机械 AUTOMATIC TRIMM ING MACHINE拉钉打头机 BLIND RIVET HEADING M ACHINE螺丝、螺帽成型机 BOLT FORMERS,NUT S FORMERS,HEADERS螺丝、螺帽热处理 BOLT NUT AND SCR EWS HEAT TREATMENT螺丝、螺帽热处理炉 BOLT NUT AND S CREWS HEAT TREATMENT FURNACES 球状化电器炖炉 CARBURIZING FURNA CE VACUUM AND BELL TYPE FURNACE 超防锈复合瓷膜 CERAMIC COATING 连续式光辉渗碳淬火炉 CONTINUOUS BRIGHT CARBURIZING QUENCHING FUR NACE连续式光辉?#123;质淬火炉 CONTINU OUS BRIGHT HARDENING QUENCHING F URNACE中、高热镀涔廨x连续炉 CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉 CONTINUOUS TY PE BRIGHT HEAT TREATMENT FURNACE螺丝割尾及特殊割遘加工 MACHINE S CREW SHANK SLOTTING螺丝钻孔加工 SCREW SHANK DRILLIN G鸡眼上下模 EYELETS DIES一般线材、盘元、退火炉 GENERAL WI RE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机 HANDSTAND TYP E WIRE DRAWING MACHINE十字冲模 HEADER PUNCHES IN VARIO US DRIVES成型冲模 HEADER PUNCHES IN VARIO US DRIVES螺丝打头机 HEADING MACHINE螺丝制造高速搓牙机械 HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉 HIGH,MEDIUM, LOW FREQUENCY INDUCTION HEATER 空心打头机 HOLLOW HEADING MACHIN E热浸镀渎萁z、螺帽 HOT DIP GALVAN IZING BOLTS AND NUTS机械镀 MECHANICAL GALVANIZED迷你成型机 MINI-FORMERS成品自动收线机 NON-STOP COILER 精抽自动收线机 NON-STOP COILER(S KINPASS)螺帽模 NUT FORMING DIES螺帽成型模 NUTS FORMERS特殊零件成型机 PARTS FORMING MAC HING冲模 PUNCH DIES冲子 PUNCH PINS罗拉成型机 ROLLERS FORMERS机(踏)车用螺丝成型机 SCREW FOR M OTORCYCLE OR BICYCLE HEADING MAC HINE止付螺丝成型机 SET SCREWS FORMER S套高成型机 SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉 SPHE ROIDIZING BRIGHT ANNEALING FURNA CE球状化热处理炉 SPHEROIDIZING HEA T TREATMENT FURNACE攻牙机 TAPPING MACHINE螺丝攻、车刀、模具 TAPS DIES AND TOOLS搓牙机铁屑分离装置 THREAD CHIP S EPARATOR滚牙轮 THREAD ROLLING DIES牙板 THREAD ROLLING DIES PLATES 精密油压滚牙机 HYDRAULIC THREAD ROLLING MACHINES模具 TOOLS六角整头模 TRIMMING DIES HEXAGAN碳化钨模具 TUNGSTEN CARBIDE DIE 镀钛处理(TiN)专业加工服务 TiN HA RD COATING FOR CUTTING TOOLS AND PUNCHBY PVD电镀化学原料 VARIOUS ELECTROPLAT ING CHEMICALS环规校正 CALIBRATION FOR RING GA GE环规、牙规、三线规校正 CALIBRATIO N FOR RING GAGE, ATHREAD GAGE, 3 WIREGAGE螺丝、螺帽品检量测仪器 FASTENERS INSPECTION AND MEASUREMENT INSTR UMENTS螺丝、螺帽成型攻牙专用油 FORMING AND TAPPING OILS FOR BOLTS AND N UTS FORMERS螺丝、螺帽五金等检验 INSPTECTION SERVICES FOR FASTENERS AND HARDW ARE德国SCHATZ扭力机代理 REPRESENTAT IVE OF SCHATZ TORQUE MACHIN ISO品质保证系统 ISO QUALITY ASSU RANCE SYSTEM生产管理系统 PRODUCTION CONTROL SYSTEM物料管理系统 MATERIAL CONTROL SY STEM齿轮 GEARS不锈钢牙条棒 STAINLESS STEEL HRE AD ROD马达轴承轴心组件 BEARING SHAFT(M OTOR)轴承轴心 BEARING SHAFT开口铆钉 BLIND RIVETS长形拉帽 BLIND RIVET NUTS拉帽 BLIND NUTS拉钉 BLIND RIVETS实心梢 CLEVIS PINS AND STRAIGHT PINS弹片 CLIPS卷钉 COIL NAILS冷锻零件 COLD FORMING PART开口销 COTTER PINSE型环 E-RINGS膨胀螺栓 EXPANSION ANCHOR BOLTS 鸡眼钉 EYELETS RIVETSR型销 SNAP PINS闸、锁 LATCHES AND KEEPER ASSEMBL EDS其它特殊铆钉 OTHER SPECIL RIVETS销 PINS格式管夹、管束 PIPE HANGER铆钉 RIVETS螺旋锔及螺旋圈 SCREW HOOK AND SC REW RINGS中空钉 SEMI-TUBULAR RIVET开叉钉 SPLIT DRIVE ANCHORS弹簧华司 SPRING WASHERS弹簧蝴蝶夹 SPRING WINGS不锈钢华司 STAINLESSSTEEL WASHER S钢铁钉 STEEL AND IRON NAILS搓牙铁钉 THREAD NAILS钛合金铆钉 TITAIUM ALLOY RIVETS 管形铆钉 TUBULAR RIVETS华司 WASHERS真空热处理 VACUUM HEAT TREATMENT螺丝、螺帽、五金、DIY扣件 FASTEN ERS合金钢工具 ALLOY STEEL TOOLS螺栓模 BOLT HEADING DIES手动拉钉钳 HAND RIVETER船舶链 ANCHOR CHAIN脚踏车链锁 BICYCLE CHAIN LOCKS 螺丝起子 BIT罗拉 CHAIN ROLLER特殊铆合扣件 COLLARS(A BLINDFAST ENER FOR HUCK INTL)装饰链 DECORATIVE CHAINS自攻螺纹衬套 ENSAT THREADED INSE RTS六角扳手 HEXAGON KEYS超音螺纹压入式螺纹自动锁扣 THREA DED INSERTS FOR PLASTIC INJECTIO NMOULDEINGS汽车特殊杆接件 SPECIAL AUTO-MOBI LE FASTENER AS YOUR NEEDS螺纹护套 RECOIL INSERTS链条用滚子 ROLLER FOR ROLLER CHA IN金属板镶嵌组件及自动夹扣组件 SHE ET METAL FASTENERS工具套筒组件 SOCKET WRENCH SETS 不锈钢链 STAINLESS STEEL CHAINS 轭子 T-YOKE轮胎链 TIRE CHAINS狗链 DOG CHAINS喇叭头轭铁 U-YOKE,T-YOKE FOR SPE AKER不锈钢输送带轮用轨道 STAINLESS W HEEL'S RACK FOR TRANSPORTER工业用链 INDUSTRIAL STEEL LINK C HAINS拖链安全链 TOW CHAINS AND SAFETY CHAINS机车离合器零件 MANUFACTURE OF MO TORCYCLE'S CVT PARTS牙条棒 THREAD ROD2006-7-22 17:25 xuzhengyu4、焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas weldi ng MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接 series sea m welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬Normteile标准件Gewinde, Schrauben, Muttern螺纹、螺栓、螺母Gewinde螺纹Schrauben螺栓Gewindeauslufe螺纹收尾、肩距Gewindefreistiche螺纹退刀槽Senkungen锪孔、沉孔Mutter螺母Scheibe档圈Schlüsselweite扳手口尺寸Werkzeugvierkante工具四方柄Stifte, Bolzen, Niete, Mitnehmer verbindungStifte 圆柱销Kerbstifte弹性销Bolzen轴销Keile 键Federn弹簧Keilwellenverbindung花键连接Blindniete抽芯铆钉Werkzeugkegel刀具、工具锥度Normteile für Vorrichtungen und Standzwerkzeuge工装夹具和冲裁模具的标准件Normteile für Vorrichtungen工装夹具的标准件T-NutenT型槽Kugelscheiben球面垫圈Normteile für St anzwerkzeuge冲裁模具标准件Federn弹簧Antriebstechnik传动技术RiementriebeV型带传动Gleitlagerbuchsen滑动轴承轴瓦W?lzlager滚动轴承Nutmuttern圆螺母Passscheiben配合垫圈Stützscheiben调整垫圈Wellenenden轴端Wellendichtring轴用密封件RunddichtringO型密封圈机械工具Mechanic“s Tools spanner 扳子 (美作:wrench) double-ended spanner 双头扳子adjustable spanner, monkey wrenc h 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench)calipers 卡规pincers, tongs 夹钳shears 剪子wire cutters 剪线钳multipurpose pliers, universal p liers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯rivet 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈staple U形钉grease gun 注油枪oil can 油壶jack 工作服机械加工抛光 polishing安装 to assemble扳手 wrench半机械化 semi-mechanization; sem i-mechanized半自动滚刀磨床 semi-automatic ho b grinder半自动化 semi-automation; semi-a utomatic备件 spare parts边刨床 side planer变速箱 transmission gear柄轴 arbor部件 units; assembly parts插床 slotting machine拆卸 to disassemble超高速内圆磨床 ultra-high-speed internal grinder车床 lathe; turning lathe车刀 lathe tool车轮车床 car wheel lathe车削 turning车轴 axle衬套 bushing 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & ho lding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM)电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion she et making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & v ertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical doubl e-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & hori zontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for al uminium wheels 铝轮冒口切断机P type PVC waterproof rolled she et making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machi nes 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯 Saws,hack 弓锯Saws,horizontal band 卧式带锯 Saws,vertical band 立式带锯 shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床 spindles 主轴Stamping parts 冲压机Straightening machines 矫直机 Switches & buttons 开关及按钮 Tapping machines 攻螺丝机 Transmitted chains 传动链 Tube bending machines 弯管机 Vertical hydraulic broaching mac hine 立式油压拉床 Vises 虎钳Vises,tool-maker 精密平口钳 Wheel dressers 砂轮修整器 Woven-Cutting machines 织麦激光切割机Wrenches 扳手 有无其他意见或说法？单元式幕墙 unitized curtain wall 垂直幕墙 vertical curtain wall典型幕墙单元typical curtain wall unit 点支式幕墙 point supporting curtain wall 吊顶幕墙 overhang curtain wall 悬挂玻璃幕墙 suspended window wall 直面幕墙 flat curtain wall 智能幕墙 intelligent curtain wall隐框玻璃幕墙hidden framing glass curtain wall 构件式玻璃幕墙 component glass curtain wall光电幕墙 photoelectric curtain wall 后片玻璃 second lite夹层玻璃 laminated glass/laminate 夹胶玻璃 laminated glass溅涂浮法玻璃 sputter-coated float glass 金属幕墙 metal curtain wall明框玻璃幕墙exposed framing glass curtain wall内循环双层玻璃幕墙 internal cycle double-skin cu 倾斜幕墙 sloped curtain wall全玻璃幕墙 full glass curtain wall; lass wall wi 热反射镀膜幕墙heat reflecting coated curtain 双层呼吸式幕墙 double-skin curtain wall 石材幕墙 stone cladding curtain wall 陶板幕墙 terracotta curtain wall 索网幕墙 cable-net curtain wall单层索网幕墙 single-layer cable-net curtain wall外循环双层玻璃幕墙 external cycle double skin gl 微晶玻璃幕墙 crystallite glass cladding铝板幕墙 aluminum cladding ；aluminum panel curta 明框 exposed frame。

幕墙设计中英文对照*香港远东铝质集团**企业统一制图编号:GC 花岗石外墙挂板Granite Cladding LV 百叶窗Louver FT 特别设计 装饰件Special Feature SL 天窗 Skylight GW 玻璃墙Glass WallSF 橱窗 Storefro nt BT 栏杆 BalustradeGR 窗花 Grills MA旗杆MastCP雨蓬 Canopy*部分专业名词注释:平面图 PLAN 立面图 ELEVATION剖面图SECTION 柱 PILLAR 梁 GIRDER 桁架 TRUSS水槽CUTTER排水孔WEEP HOLE水泥砂浆CEMENT GROUT轴线AXIS分格尺寸 MODULE DIMENSION 横向节点图 MULLION DETAIL 竖向节点图 TRANSOM DETAIL 幕墙CURTAIN WALL 室外装饰层 EXTERNAL FINISH 防水涂层WATERPROOF室内天花板INTERIOR CEILING室内外完成面 EXTR AVENTRICULAR(INTERIOR) FLOOR BY OTHERS2 〜铝型材 ALUMINIUM EXTRUSION氟碳喷涂铝板铝板、铝片 ALUM.CLADDING PVF2.PANEL ALUM. PANEL复合铝板 COMPOSITES ALUM. PANELALUM. CLIP(BLACK ANODIZED) ALUM. MULLION ALUM. SILL BOARD ALUM.TRANSOMALUM. STOOL TRIMMING ALUM. FRAMEALUM. PLEMET COVER ALUM. HOLLOW ALUM. COVER ALUM. SLEAVE ALUM. FLAT BAR ALUM. BACK PANCW~ WW~ AC~SC~ 玻璃幕墙Curtain Wall 带型窗 Window Wall铝板幕墙 Alum Cladding 不锈钢挂板 Stainless Steel CladdingEL~ PE~ DT~ WD 总平立剖面 局部平立剖面 节点铝窗Window铝夹（黑色电镀） 铝竖框 铝窗台板 铝横框 铝托架 铝框 铝窗廉盖 铝通铝（盖）装饰条 铝套筒 铝扁巴（条） 铝背板铝百叶ALUM. LOUVRE接驳件SPIDER FIXING铝管ALUM. CHANNEL铝角ALUM. ANGLE铝锚托架ALUM. ANCHOR BRACKET铝轻型槽ALUM. LIGHT TROUGH铝锚片ALUM. ANCHOR PLATE铝垫圈ALUM. WASHER PLATE (6063-T6)磨光边框GLAZING FRAME铝型材ALUM. EXTRUSION锯齿垫圈SERRATED WASHER铝副框ALUM. ADAPTOR 铝基板ALUM. SILL BOARD 铝角立柱CORNER ALUM. MULLION (6063-T6) PVF2 FINISH铝横梁盖ALUM. TRANSOM COVER (6063-T5) PVF2 FINISH 铝水槽ALUM. GUTTER铝窗扇ALUM. WINDOW SASHALUM. TRIMMING 铝支架ALUM. SUPPORT铝压板ALUM. PRESSER〜3〜钢结构STEEL FRAME 铝通STEEL HOLLOW“工”字钢STEEL“ I” BEAM 矩形钢管REC. STEEL TUBE 镀锌角钢G.M.S. ANGLE STEEL 镀锌钢( 垫) 介子G.M.S. WASHER 钢构件STEEL WORK冷弯钢ECONOMIC STEEL镀锌槽钢G.M.S. CHANNEL 镀锌钢板G.M.S. PLATE 不锈钢折弯槽S.S. BEND CHANNEL不锈钢STAINLESS STEEL (S.S. ) 预埋件G.M.S.EMBED不锈钢“T”型梁S.S. “ T” BEAM “ T”型钢STEEL T SECTION 发丝不锈钢板S.S. PLATE(HAIRLINE FINISH) 钢管STEEL TUBE石板FLAG STONE密封胶（防水胶）WEATHERSEAL SEALANT 结构胶绝缘垫片ISOLACTION SHEET 双面胶带玻璃密封胶（夹胶玻璃专用密封胶）BETA-SEAL 海绵条STRUCTURAL SEALANT DOUBLE SIDE TAPE SPONGEM5x15 S.S PH. SELF TAPPING SREW M5x15: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝 （ 分使用于金属与使用于塑料二种 ） B-1: Sheet Metal Tapping Screw. （ 铁板牙自攻螺丝 ） B-2: Plastic Tapping Screw. （ 塑料用 , 自攻螺丝 ） C: Wooden Screw : 木工螺丝 D: Drywall Screw : 水泥墙螺丝 E: Self Drilling Screws 钻尾螺丝（不锈钢钻尾螺丝，复合材料钻尾螺丝） E-1:STAINLESS STEEL SELF DRILLING SCREW 不 锈钢钻尾螺丝 E-2:Bi-Metal Self Drilling Screws 复合材料钻尾螺丝〜4〜（玻璃） 中空 玻璃RISION INSULATION GLASS夹胶 玻 璃 LAMINATED GLASS 钢 化 清玻 璃 CLEAR IRON TEMPERED GLASS 玻 璃 栏 杆 GLASS BALUSTER单片 玻 璃 MONOLITHIC GLASS 12（LOW-E ）+12A+12 钢 化中 空玻 璃 12HS LOW-E+12+12HS INSULATING GLASS8mm 钢化玻璃（加铝背板） 8mm HS OPAQUE GLASS （ALUMINIUM BACK PAN ）〜 4〜 （ 其 它 ） 厚 度 THK.ALUM. ADAPTER 铝 附 框 ALUM. PRESSER 铝 压 板MULTI-POINT LOCKING DEVICE 锁点LOCK BOX W/REMOVABLE HAN 锁箱（手柄可拆卸）钢 通 STEEL. HOLLOWCEMENT GROUTINE 水泥 防水 砂 浆防潮 板 WATERPROOF聚脂 塑料 填塞 棒（ 小圆 棒） BACKER ROD 保温 棉 THERMAL INSULATION1 小 时 防 火 棉 1 HOUR FIRE STOP INSULATION 化学 螺栓 CHEMICAL BOLT 不锈 钢平 头螺 栓 S.S. F.H. BOLT （F.H.S ） 不锈钢六角头螺栓配垫片 不 锈 钢 沉 头 螺 丝 S.S. S.S. P.H. SCREW橡胶 条 GASKET 垫 片 SHIM 橡胶 垫 块 EPDM SEALANT地脚 螺栓 TRUSS BOLT 膨 胀螺 栓EXPANSION BOLT埋头 螺 丝 DORMANT SCREW植钉STUDALUM.钢钉铝铆 钉 ALUM. RIVES.S. H.E.X. HEAD BOLT&WASHER F.H. SCREW DRIVING PIN不 锈 钢 盘 头 螺 丝 （P.H.S ）射 钉 PIN 不锈钢自攻螺钉WALL CENTRE LINE 墙中心线保温钉AL. FIXING PIN 隔离垫块1mm PVC ISOLATOR THERMAL BREAK 断桥幕墙强度要求eV [ c ];幕墙刚度要求，当跨度小于4.5米，铝质龙骨满足相对挠度，净跨/175和绝对挠度19mm较小者，当跨度在4.5至12米之间，铝质龙骨满足相对挠度，跨度/240和绝对挠度38m m较小者，钢质龙骨满足相对挠度，净跨/250。

client 业主check and approve 审核submit 提交tender/bid 投标vapor barrier 防潮层dimension 尺寸diameter 直径shelf life 保质期gasket 垫片，胶条bracket 托架，码件shim 垫片washer 垫圈trim 护边finish 装饰面polish 抛光bend 弯折，弯曲cast 浇铸mill finish 毛料，光身料（没有喷涂的材料）stillage 装运箱timber 木材frit 玻璃料gypsum 石膏cavity 腔profile 剖面coping 顶corrosion 腐蚀rotation 旋转penetration 穿透remainder 剩余的，其他的membrane 薄膜serration 锯齿状serrated 锯齿状的froth rod / backer rod 泡沫棒cell closed sponge 闭孔海绵caulk on both sides 两侧封堵deburr after fabrication 加工后清理毛刺mullion – transom 立柱--横梁bolt 螺栓screw 螺丝nut 螺母threaded weld stud 螺纹焊柱member 构件Allen head 内六角concrete collar 混凝土圈梁ETA 预计到达期(estimated time of arriving) OT container 开顶柜/箱(open top)GP 普通用途集装箱(general purpose)RF 冷冻柜(reefer container)VMU 视觉样板(visual mock-up)PMU 性能测试样板(performance mock-up) FW - façade wallopaque 不透明的Low iron glass 超白玻SGP 夹胶玻璃OPTI clear glass 轻玻璃HST 热浸处理(Heat Soak Test)shop drawing 施工图die drawing 模图fab drawing 加工图tag drawing 布置图elevation 立面图marking drawing 编号图plan 平面图layout 规划图unit tag 板块编号钢筋steel reinforcement刚度rigidity玻璃面板glass panel中空玻璃hollowed glass铝合金aluminum alloy结构胶structural sealant隔热heat insulation镀锌钢galvanized steel质心centroid外围护结构enclosure construction剪力墙shear wall女儿墙parapet悬臂梁cantilever beam。

幕墙设计中英文对照东铝质集团*EL~ 总平立剖面WW~ 带型窗Window Wall PE~ 局部平立剖面AC~ 铝板幕墙Alum Cladding DT~ 节点SC~ 不锈钢挂板Stainless Steel Cladding WD 铝窗WindowGC 花岗石外墙挂板Granite Cladding LV 百叶窗LouverFT 特别设计装饰件Special Feature SL 天窗SkylightGW 玻璃墙Glass Wall SF 橱窗StorefrontBT 栏杆Balustrade GR 窗花GrillsMA 旗杆Mast CP 雨蓬Canopy平面图PLAN 立面图ELEVATION 剖面图SECTION 柱PILLAR 梁GIRDER 桁架TRUSS水槽CUTTER 排水孔WEEP HOLE 水泥砂浆CEMENT GROUT轴线AXIS 分格尺寸MODULE DIMENSION横向节点图MULLION DETAIL 竖向节点图TRANSOM DETAIL幕墙CURTAIN WALL 室外装饰层EXTERNAL FINISH防水涂层WATERPROOF 室内天花板INTERIOR CEILING室内外完成面EXTR AVENTRICULAR(INTERIOR) FLOOR BY OTHERS～2～铝型材ALUMINIUM EXTRUSION氟碳喷涂铝板ALUM.CLADDING PVF2.PANEL铝板、铝片ALUM. PANEL复合铝板COMPOSITES ALUM. PANEL铝夹(黑色电镀) ALUM. CLIP(BLACK ANODIZED)铝竖框ALUM. MULLION铝窗台板ALUM. SILL BOARD铝横框ALUM. TRANSOM铝托架ALUM. STOOL TRIMMING铝框ALUM. FRAME铝窗廉盖ALUM. PLEMET COVER铝通ALUM. HOLLOW铝（盖）装饰条ALUM. COVER铝套筒ALUM. SLEAVE铝扁巴（条）ALUM. FLAT BAR铝背板ALUM. BACK PAN铝百叶ALUM. LOUVRE接驳件SPIDER FIXING铝管ALUM. CHANNEL铝角ALUM. ANGLE铝锚托架ALUM. ANCHOR BRACKET铝轻型槽ALUM. LIGHT TROUGH铝锚片ALUM. ANCHOR PLATE铝垫圈ALUM. WASHER PLATE (6063-T6)磨光边框GLAZING FRAME铝型材ALUM. EXTRUSION锯齿垫圈SERRATED WASHER铝副框ALUM. ADAPTOR铝基板ALUM. SILL BOARD铝角立柱CORNER ALUM. MULLION (6063-T6) PVF2 FINISH铝横梁盖ALUM. TRANSOM COVER (6063-T5) PVF2 FINISH铝水槽ALUM. GUTTER铝窗扇ALUM. WINDOW SASHALUM. TRIMMING铝支架ALUM. SUPPORT铝压板ALUM. PRESSER～3～钢结构STEEL FRAME 钢构件STEEL WORK铝通STEEL HOLLOW“工”字钢STEEL “I”BEAM 冷弯钢ECONOMIC STEEL矩形钢管REC. STEEL TUBE 镀锌槽钢G.M.S. CHANNEL镀锌角钢G.M.S. ANGLE STEEL 镀锌钢板G.M.S. PLATE镀锌钢（垫）介子G.M.S. WASHER 不锈钢折弯槽S.S. BEND CHANNEL 不锈钢STAINLESS STEEL（S.S.）预埋件G.M.S.EMBED不锈钢“T”型梁S.S. “T”BEAM “T”型钢STEEL T SECTION发丝不锈钢板S.S. PLATE(HAIRLINE FINISH) 钢管STEEL TUBE石板FLAG STONE～4～密封胶（防水胶）WEATHERSEAL SEALANT 结构胶STRUCTURAL SEALANT绝缘垫片ISOLACTION SHEET 双面胶带DOUBLE SIDE TAPE玻璃密封胶（夹胶玻璃专用密封胶）BETA-SEAL 海绵条SPONGE防潮板WATERPROOF 橡胶条GASKET聚脂塑料填塞棒（小圆棒）BACKER ROD 垫片SHIM保温棉THERMAL INSULATION 橡胶垫块EPDM SEALANT1小时防火棉 1 HOUR FIRE STOP INSULATION 地脚螺栓TRUSS BOLT化学螺栓CHEMICAL BOLT 膨胀螺栓EXPANSION BOLT 不锈钢平头螺栓S.S. F.H. BOLT (F.H.S) 埋头螺丝DORMANT SCREW不锈钢六角头螺栓配垫片S.S. H.E.X. HEAD BOLT&WASHER不锈钢沉头螺丝S.S. F.H. SCREW 不锈钢盘头螺丝(P.H.S) S.S. P.H. SCREW植钉STUD ALUM.钢钉DRIVING PIN 射钉PIN铝铆钉ALUM. RIVEM5x15 S.S PH. SELF TAPPING SREW M5x15 不锈钢自攻螺钉: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal T apping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝E: Self Drilling Screws 钻尾螺丝（不锈钢钻尾螺丝，复合材料钻尾螺丝）E-1:STAINLESS STEEL SELF DRILLING SCREWS 不锈钢钻尾螺丝E-2:Bi-Metal Self Drilling Screws 复合材料钻尾螺丝～4～（玻璃）中空玻璃RISION INSULATION GLASS 夹胶玻璃LAMINATED GLASS钢化清玻璃CLEAR IRON TEMPERED GLASS 玻璃栏杆GLASS BALUSTER单片玻璃MONOLITHIC GLASS12(LOW-E)+12A+12钢化中空玻璃12HS LOW-E+12+12HS INSULATING GLASS8mm钢化玻璃(加铝背板) 8mm HS OPAQUE GLASS(ALUMINIUMBACK PAN)～4～（其它）厚度THK.ALUM. ADAPTER 铝附框ALUM. PRESSER 铝压板MULTI-POINT LOCKING DEVICE 锁点LOCK BOX W/REMOVABLE HANDLE锁箱（手柄可拆卸）钢通STEEL. HOLLOWCEMENT GROUTINE 水泥防水砂浆WALL CENTRE LINE 墙中心线保温钉AL. FIXING PIN隔离垫块1mm PVC ISOL ATORTHERMAL BREAK 断桥幕墙强度要求σ＜[σ]；幕墙刚度要求，当跨度小于4.5米，铝质龙骨满足相对挠度，净跨/175和绝对挠度19mm较小者，当跨度在4.5至12米之间，铝质龙骨满足相对挠度，跨度/240和绝对挠度38mm较小者，钢质龙骨满足相对挠度，净跨/250。

玻璃Annealed[ə'ni:l] glass退火玻璃Ceramic[si'ræmik] frit [frit]glass彩釉玻璃Clear glass (non-opaque[əu'peik])透明玻璃Double ['dʌbl] glazing ['ɡleiziŋ]双层（中空）玻璃Facial ['feiʃəl] glass (façade [fə'sɑ:d] glass)面玻璃Figured ['fiɡə] glass压花玻璃Fin glass (stiffen ['stifən] fin glass)肋玻璃Float [fləut] glass浮法玻璃Half（heat）strengthened['streŋθən] glass半钢化玻璃Insulating['insjuleit] glass中空玻璃Laminated['læmineit] glass夹层玻璃（夹胶玻璃）Louver['lu:və] glass百叶玻璃Monumental [,mɔnju'mentəl]glazing巨幅玻璃（全玻）Polished['pɔliʃ] glass磨光玻璃Reflective [ri'flektiv] glass反射玻璃Single toughened ['tʌfən] glass单层钢化玻璃opaque glass不透明玻璃Tempered['tempə] glass(toughened glass) 钢化玻璃门窗Water-tightness [taitnis] performance[pə'fɔ:məns]防水性能Permeability[,pə:miə'biliti]（infiltration[,infil'treiʃən], penetration[,peni'treiʃən]）performance密闭性能Noise insulation [,insju'leiʃən]噪音绝缘Heat resistant [ri'zistənt] property 隔热性能Sound insulation 隔音Wind pressure resistance抗风性能Water resistance 防水Optimal ['ɔptiməl] thermal['θə:məl] efficiency [i'fiʃənsi] and weather resistance极好的节能性和防腐蚀性Fingertip['fiŋɡətip] -easy to operate 极易操作Custom-made to our clients'['klaiənt] specifications[,spesifi'keiʃən]依客户的特殊需求定做Mill [mil] finish光面Anodizing['ænəudaiz] 阳极氧化处理Powder coated粉末喷涂Performance parameters[pə'ræmitə] 性能参数Flake [fleik], chip [tʃip], peel [pi:l], corrode [kə'rəud]剥落，碎裂，腐蚀Hardware; ironmongery['aiən,mʌŋɡəri]五金Handle ['hændl]执手Loose [lu:s] preventer[pri'ventə]防松垫片Misuse preventer防误传动杆Locking plate[pleit]锁块，锁座Corner device[di'vais]转角器Transmission [trænz'miʃən] rod [rɔd]传动杆Overturn supporter翻转支撑Disengagement [disin'ɡeidʒmənt] preventer防脱器Supporting block支撑块Shim垫块Water cap防水盖Pivot ['pivət] hinge[hindʒ]合页Active lock point活动锁点Socket ['sɔkit] rod插销杆Friction ['frikʃən] stay 铰链Roller滑轮Counter sunk screw十字沉头螺钉Cylinder ['silində]锁芯Structural ['strʌktʃərəl] opening门窗洞口Frame框Appendent[ə'pendənt] frame隐框Operable ['ɔpərəbl] leaf活动扇Active leaf先开扇Inactive leaf后开扇Fixed leaf固定扇Unrebated leaf平开扇Rebated['ri:beit]leaf企口扇Unilateral [,ju:ni'lætərəl] rebated leaf单企口扇Bilateral rebated leaf双企口扇Multilateral rebated leaf多企口扇Active part of window and door可开启部分Fixed part of window and door固定部分Panel; infill镶板Lining筒子板Trim; architrave['ɑ:kitreiv]贴脸板Sash 窗扇Casement 窗扉Slotted weep holes 排水孔Drainage排水Weather stripping挡雨条Lift rail抬拉杆Integral ['intiɡrəl] pull bar推拉杆Slide pad滑动垫Internal screens内网（好象是纱窗之类）Head上框Jamb[dʒæm]边框Transom['trænsəm]中横框Mullion['mʌliən]中竖框Sill下框Combination [,kɔmbi'neiʃən] transom and mullion拼樘框（包括横向和竖向）Toprail上挺Middle rail中横挺Stile [stail]边挺Hooked stile带钩边挺Bottom rail下挺Weather stile封口边挺Glazing bead玻璃压条Horizontal ['hɔri'zɔntəl] muntin ['mʌntin]; Horizontal glazing bar横芯Vertical muntin; Vertical glazing bar竖芯Weather strip披水条Inherent weather strip 固有披水条Appendent [ə'pendənt] weather strip附加披水条Weather board 披水板Window board窗台板Structural ['strʌktʃərəl] opening with non-rebated reveal平开洞口Structural opening with rebated reveal槽开洞口Soffit['sɔfit]洞口顶面Sill洞口底面Vertical side洞口侧面Structural rebate槽口Depth[depθ] of rebate槽口深度Coordinating height between opening and frame of window and door洞口高度标志尺寸Height of structural reveal洞口高度构造尺寸Height of window and door frame门窗高度构造尺寸Coordinating height between frame and leaf of window and door门窗高度标志尺寸Window and door frame reveal height门窗框槽口高度Clear opening height of window and door frame门窗框洞口净高度Height of window and door leaf (inside window and door frame)门窗扇高度（在门窗框内）Window and door leaf height overall lipping门窗扇高度（包括企口凸边）Width of window and door门窗宽度构造尺寸Coordinating width between frame and leaf of window and door门窗扇宽度标志尺寸Window and door frame reveal width门窗框槽口宽度Clear opening width of window and door门窗洞口净宽度Width of window and door leaf (inside window and door frame)门窗扇宽度（在门窗框内）Window and door lead width overall lipping门窗扇宽度（包括企口凸边）Width of rebate (of the frame)门窗框槽口宽度Depth-thickness深度-厚度Coordinating thickness between opening and frame of window and door墙体或其槽口深度标志尺寸Depth of structural reveal and rebate墙体或其槽口深度构造尺寸Window and door frame thickness门窗框厚度构造尺寸Coordinating depth between frame and leaf of window and door门窗扇与门框间槽口的深度标志尺寸Window and door frame reveal rebate depth门窗框槽口的深度构造尺寸Window and door lead reveal rebate depth门窗扇槽口深度Thickness of window and door leaf (inside window and door frame)门窗扇厚度（在门窗框边）Window and door leaf thickness overall lipping 门窗扇厚度（包括企口凸边）Gap width[widθ]缝隙宽度Joint clearance between door frame and appendent frame门窗框与附框接缝间隙Joint clearance between appendent frame and structural opening 附框与洞口接缝间隙Vertical clearance between door frame and leaf of window and door (at the side of no hinge)门窗框与扇间无合页（铰链）一侧的缝隙Vertical clearance between door frame and leaf of window and door (at the side of hinge) 门窗框与扇间有合页（铰链）一侧的缝隙Horizontal upside clearance between door frame and door leaf;or horizontal upside and underside clearance between window frame and sash门框与门扇间上侧缝隙或窗框与窗扇间上下侧缝隙Clearance between door leaf and finished floor门扇与地面间的缝隙Door 门Door set整樘门Operable door活动门Fixed door固定门Door frame 门框Door leaf门扇External [ik'stə:nəl] door外门Terrace ['terəs, -is] d oor阳台门Strom door风雨门Internal door内门Exit door安全门Escape [i'skeip] door逃生门Side-hung[hʌŋ] door平开门Sliding door推拉门Lifting sliding door提升推拉门Folding door折叠门Right revolving [ri'vɔlv] door 转门Rolling door卷门Flush [flʌʃ] door 夹板门Paneled door镶板门Glazed door镶玻璃门Glass door 全玻璃门Fixed glass（infill panel）door固定玻璃（镶板）门Grille [ɡril] door 格栅门Shutter ['ʃʌtə] door百叶门Door with screen sash带纱扇门Door with side window带窗门Dual（double）door双重（层）门Primary ['praiməri] door主门Secondary ['sekəndəri] door次门Window 窗Operable window活动窗Fixed window固定窗External window外窗Internal window内窗Storm window风雨窗Vent window换气窗French window落地窗Escape window逃生窗Observation window观察窗Show window橱窗Side-hung window or casement window平开窗Top-hung casement opening outward外开上悬窗Bottom-hung casement opening inward内开下悬窗Tilt and turn window, opening inward内开内倒窗Sliding window推拉窗Lifting sliding window提升推拉窗Vertical sliding window; sash window上下推拉窗Louvered window百叶窗Louvered window with active leaves活动百叶窗Strip [strip] window条形窗Bay [bei] window凸窗Bow [bəu] window弓形窗Oriel window凸肚窗Hidden frame window隐框窗Roof window屋顶窗Skylight天窗Fixed skylight固定天窗Window frame 窗框Casements平开窗扇Sashes推拉窗扇Fanlight亮窗Fixed light固定亮窗幕墙Alloy['ælɔi]合金Aluminum[ə'lju:minəm]铝Bead[bi:d]压条Bracket ['brækit]支托，支架Bolt 螺栓Canopy['kænəpi]天棚，雨棚Casement window平开窗Concrete[kən'kri:t]混凝土Contractor['kɔntræktə]承包商Corridor['kɔridɔ:]过道Curtain ['kə:tən] wall 幕墙Detail['di:teil]节点图Dining餐厅Elevation [,eli'veiʃən]立面图Embedded [im'bed]埋件Façade墙Fence 栅栏，围墙Finish装饰，表面处理Fire prevention 防火Flashing[flæʃ]防水板，遮雨板Folded折叠的Frame框架Front前面Grilling格栅Handrail['hændreil]扶手Hardware（ironware）五金Hinge合页Hot-dipped (hot soaked)热浸Indemnity[in'demnəti]赔偿Galvanize ['ɡælvənaiz]（galvanization [,ɡælvənai'zeiʃən]）镀锌Granite ['ɡrænit] cladding石材Living客厅Louver百叶Maximum['mæksiməm]最大值Minimum ['miniməm]最小值Screw螺丝Sliding window推拉窗Skylight roof 采光顶Supplier供应商Gasket['ɡæskit]胶条Parapet ['pærəpit]（podium ['pəudjəm]）女儿墙Performance[pə'fɔ:məns]性能Plan 平面图Plastic塑料的Plate 金属板，板Plywood['plaiwud]胶合板Powder coating/coated 粉末喷涂Quality 质量Quantity 数量Rear[riə]后面Rod 拉杆Roof屋顶Sealant 封胶Section剖面图Specification 规格，详述S/S= Stainless steel不锈钢Sub-contractor分包商Tape（shim）垫块Temperatur['tempəritʃə]e温度Terrace ['terəs]（balcony ['bælkəni]）阳台，平台Thickness厚度Tolerance['tɔlərəns]公差Weld 焊接Width宽度Zinc-plated镀锌。

Annealed glass 退火玻璃[ə’ni:l] Anodizing 阳极氧化[‘ænədaiz]Axial 轴向的[‘æksiəl]backer rod 泡沫棒 [rɔd]critical 危险的，临界的deduction 折减，扣除 [di’dʌkʃən] deflect 挠度 [di‘flekt]deformation 变形 [，di:fɔ:‘meiʃən] developed area 展开面积gasket 垫圈glazing玻璃窗、上釉、上光high-span 大跨度louver 天窗[‘lu:və]MR（moisture resistant）防潮[‘mɔistʃə] metal spacer 金属隔片overall thickness 总厚度polystyrene聚苯乙烯[,pɔli’staiəri:n] rain-screen 雨幕fabricate 加工sash windows上下推拉窗sliding windows 左右趟拉式窗venting 通风4-way lock 四点锁as-built drawing 竣工图screwed connection 螺纹连接[skru:d]slag cotton矿棉site-welding 现场焊接CURTAIN WALL SOUTH ELEVATION [，eli‘veiʃən] 玻璃幕墙南立面图CURTAIN WALL DEVELOPMENT 玻璃幕墙展示图CURTAIN WALL SECTION 玻璃幕墙剖面图CURTAIN WALL PARTIAL ELEVATION玻璃幕墙部份立面图 [‘p ɑ:ʃəl]CURTAIN WALL TYPICAL PLAN玻璃幕墙标准层平面图CURTAIN WALL TYPICAL PRE-CAST LAYOUT PLAN玻璃幕墙标准层预埋件平面图CURTAIN WALL DETAIL玻璃幕墙节点图50mm thickness thermal insulation 50mm 厚隔热棉[‘θə:məl] 1mm thickness EPDM separator 1mm厚绝缘胶片（EPDM三元乙丙橡胶）[‘sepəreitə]female mullion 母料/阴竖料[‘mʌliən]male mullion 公料alum.female /male mullion 铝合金阴阳竖料transom横料[‘trænsəm]head transom 头料sill transom 尾料[sil]bead压条[bi:d]adaptor 扣件 [ə‘dæptə]gutter sleeve 过桥external corner外转角[eks’tə:nl]internal corner 内转角D.S.T. = double side tape双面胶带double skin facade [fə‘sɑ:d] 双层幕墙zinc chromate [‘krəumeit]烙酸锌PVF氟碳烤漆powder coat 粉沫喷涂granite 花岗石[‘ɡrænit]aluminum alloy [‘ælɔi]铝合金 Mild steel 钢butt welding 焊缝[bʌt]alum. panel 铝板Stainless steel bolt 不锈钢螺栓[bəult]transom 横柱 Mullion 立柱embedment 预埋件[im‘bed]structural silicone 结构胶[’silikəun]weather proofing sealant 耐侯胶 [pru:f] [‘si:lənt]steel bracket 钢角码Alum bracket 铝角码single tempered glass 单层钢化玻璃[‘tempəd]zinc-plated 镀锌 [‘pleitid]半钢化玻璃：heat strengthened glass [‘streŋθən]浮法玻璃float glass中空玻璃：insulating Glass夹胶玻璃：laminated glass [‘læmineitid]机制螺栓 machine bolt镀锌螺栓 galvanized bolt [‘ɡælvənaiz]膨胀螺栓expansion bolt [iks’pænʃən]锚拴anchor bolt [‘æŋkə]泡沫填充棒foam rod刚性绝缘体 rigid insulation [‘ridʒid]镀锌 galvanizing [‘ɡælvənaiz]焊缝 welding line 防火棉 fire stop4mm THK. COMPOSITE MADE OF AL. AND PLASTIC 4厚复合铝板5mm THK. ALUMINUM PLATE 5厚单铝板角焊缝是fillet weld [‘filit]对接焊缝是butt weldtoughened glass [‘tʌfn]是指强化玻璃，在国内一般不说，对应的是半钢化玻璃可见光透光率 visible Light Transmittance [træns’mitəns]可见光反射率visible Light Reflectance [ri’flektəns]U-值 U-value遮阳系数 shading coefficient [kəui’fiʃənt]相对热增益 relative Heat Gain引爆处理 hat Soak Test [səuk]双层幕墙 double Skin Wall滴水 weep 泛水 Flashing 采光顶 Skylight 雨棚 Canopy fire rating clip防火棉插facial glass面玻璃figured Glass压花玻璃die 冲模 [dai]fin glass肋玻璃distributed 均匀的分布的 [dis’tribju:tid]double glazing 双层（中空）玻璃downwind 顺风面upwind 迎风面drive pin 射钉free stand type 坐落式earthquake load 地震荷载granite cladding 干挂石 [ˈɡrænit]Exposed frame 明框Hidden frame 隐框Immediate 立即的 [i‘mi:diət]inertial moment 惯性矩 [i‘nə:ʃəl] penetration butt 对接埋入焊 [peni‘treiʃən] joist 托梁 [dʒɔist]lateral 侧面的，旁边的podium 裙房 [‘pəudiəm]polished glass 抛光玻璃pre-cast 预埋railing 扶手栏杆rectangle hollow section 矩形管strut 支柱reflective glass 反射玻璃suction 吸力 [‘sʌkʃən]super-structure 主体结构restrain 约束 [ris‘trein]supplier 供应商symmetry 对称的 [‘simitri]unsymmetrical 不对称的[‘ʌnsi‘metrikəl]self-weight 自重setting block 垫块terrain 地带，范围[‘terein]the arm of force 力臂simply supported beam 简支梁site-ground 室外地面tinted 染色的 [tint]slope 倾斜 [sləup]spider fixing 固定爪triangle 三角形 [‘traiæŋɡl]universal column 通用柱variable 变量weep hole 泄水孔blade 百页片[bleid]desiccant 干燥剂 [‘desikənt]location blocks 定位块bedding 衬垫 [‘bediŋ]groove 凹槽 [ɡru:v]hidden framing glass curtain wall 隐框幕墙water-resistance glass 抗水玻璃water-proof glass 防水玻璃full glass curtain wall 全玻璃幕墙exposed framing glass curtain wall 明框幕墙semi-exposed framing glass curtain wall 半隐框玻璃幕墙[‘semi] [iks‘pəuzd]inclined glass curtain wall 斜玻璃幕墙semi-exposed framing glass curtain wall半隐框玻璃幕墙sag/cave in 凹陷 [sæɡ]skeleton and skin system 骨架结构 [‘skelitn] switchbox 配电箱underground network of pipes 地下管网shell system 壳体结构close interval 间距紧凑critical point (受力)临界点heat exchanger 空气循环prefabrication 配件预制 [,pri:’fæbrikeit] overlapping 搭接[‘əuvə‘læpiŋ]heat reflecting coated curtain wall 热反射镀膜幕墙typical floor 标准层 typical specification 标准尺寸aluminum composite panel 复合铝板balcony railing阳台栏杆 [‘bælkəni]push-and-pull doorAAMA - American Architectural Manufacturers Association 美国建筑物制造协会ASTM - American Society For Testing And Materials 美国材料试验协会Blade 百页片 built-in内建Conceptual designs 概念设计 Canopy天蓬 Desiccant干燥剂 Deformation 变形developed area 展开面积 fenestration 开窗法 gasket 垫圈glazing玻璃窗、上釉、上光 High－span 大跨度 Hierarchica分等级的Louver 天窗 Monumental 非常规的 MR（moisture resistant）防潮metal spacer 金属隔片 overall thickness 总厚度 polystyrene聚苯乙烯rain－screen 雨幕 sunshade天棚，遮阳 sash windows上下推拉窗the National Fenestration Rating Council美国门窗保温评估协会NFRCunitized组合的 urethane聚氨酯 venting 通风 4-way lock 四点锁shopdrawing 施工图as-built drawing 竣工图 shopdrawing 施工图 as-built drawing 竣工图screwed connection 螺纹连接 slag cotton矿棉 site-welding 现场焊接CURTAIN WALL SOUTH ELEVATION 玻璃幕墙南立面图CURTAIN WALL WEST ELEVATION 玻璃幕墙西立面图CURTAIN WALL NORTH ELEVATION 玻璃幕墙北立面图CURTAIN WALL DEVELOPMENT 玻璃幕墙展示图CURTAIN WALL SECTION 玻璃幕墙剖面图CURTAIN WALL PARTIAL ELEVATION玻璃幕墙部份立面图CURTAIN WALL TYPICAL PLAN玻璃幕墙标准层平面图CURTAIN WALL TYPICAL PRE-CAST LAYOUT PLAN玻璃幕墙标准层预埋件平面图CURTAIN WALL DETAIL玻璃幕墙节点图FIRE RATING CLIP防火棉插50mm THICK THERMAL INSULATION 50mm 厚隔热棉1mm THICK EPDM SEPARATOR1mm厚绝缘胶片TOWER 塔楼 PODIUM 裙房 FEMALE MULLION 母料 MALE MULLION 公料TRANSOM 横料 HEAD TRANSOM 头料 SILL TRANSOM 尾料BEAD 压条 ADAPTOR 扣件 GUTTER SLEEVE 过桥EXTERNAL CORNER 外转角 INTERNAL CORNER 内转角D.S.T. = DOUBLE SIDE TAPE 双面胶带DOUBLE SKIN FACADE 双层幕墙 ZINC CHROMATE 烙酸锌PVF2 氟碳烤漆 POWDER COAT 粉沫喷涂玻璃幕墙-------glass curtain wallGranite 花岗石Aluminium alloy 铝合金Mild steel 钢Butt welding 焊缝Alum.panel 铝板Stainless steel bolt 不锈钢螺栓Transom 横梁Mullion 立柱Embedment 预埋件Structural silicone 结构胶Weather proofing sealant 耐侯胶Steel bracket 钢角码Alum bracket 铝角码Single glass.temperd 单层钢化玻璃Zinc-plated 镀锌钢化玻璃：Tempered glass半钢化玻璃：Heat strengthened glass 浮法玻璃：Annealed glass中空玻璃：Insulating Glass Unit (IGU) 夹胶玻璃：Laminated glass钢化玻璃：Tempered glass 半钢化玻璃：Heat strengthened glass 浮法玻璃：Annealed glass 中空玻璃：Insulating Glass Unit (IGU) 夹胶玻璃：Laminated glass 机制螺栓 MACHINE BOLT镀锌螺栓 GALVANIZED BOLT 膨胀螺栓 EXPANSION BOLT锚拴 ANCHOR BOLT泡沫填充棒 FOAM ROD刚性绝缘体 RIGID INSULATION镀锌 galvanizing不锈钢 stainless steel焊缝 welding line防火棉 FIRE STOP4厚复合铝板4mm THK. COMPOSITE MADE OF AL. AND PLASTIC5厚单铝板5mm THK. ALUMINUM PLATE焊缝统称weld，但角焊缝是fillet weld，对接焊缝是butt weldtoughened glass是指强化玻璃，在国内一般不说，对应的是半钢化玻璃JGJ102-96中，明明写结构胶译为Structural Glazing Sealant。

幕墙行业英语a.含沥青的Copper n.铜Bituminous paint 沥青油Cracked a.开裂的Board n.板Criteria n.标准，要点Bolt n.螺栓Critical a.危险的，临界的Bond v.接合,搭接Curtain wall 幕墙Bonding n.搭接,接合Curved a.弯曲的Booklet n.小册子DBottom n.底部Data n.数据Bracket n.支托Dead load 恒荷载Buckle vi.使弯曲,使屈服Deduction n.折减，扣除Built-up a.有组织的,密集的Definition n.定义，精确度C Deflection n.挠度C/C =center to center Deform v.变形Canopy n.天蓬,雨蓬Deformation n.变形幕墙常用英语Diagonal 对角线FDensity n.容重，密度Fabricate v.加工Depth n.深度Fabrication n.加工Derivation n.引出，导出Facial(façade) a.脸部的，表面的Description n.描述Facial glass (façade glass) 面玻璃Design n.设计Fatigue n.v.疲劳Detail n.详图Feature 装饰物，特征Detection n.探知，发现Figured glass 压花玻璃Development n.发展Fillet n.带子，带形的Die n.冲模Fin n.鳍，鳍状物Difference n.不同，差异Fin glass (stiffen fin glass) 肋玻璃Dimension n.尺寸Finish n.完成，装饰Direct a.ad.直接的，v.指挥Finished floor level =F.F.LDistance n.距离Fire prevention 防火Distributed a.均匀的，分布的Fix v.固定Double glazing 双层（中空）玻璃Fixing lug n.摩耳Downward a.向下的Flange n.凸缘，翼缘Downwind a.顺风面Flashing n.防水板，遮雨板Drive pin 射钉Float glass 浮法玻璃Dynamic a.活动的，动态的Folded 折叠的，拦杆Derivation n.引出，导出Force n.力，力量；v.强迫Description n.描述Foreword n.序言Design n.设计Formula n.方程Detail n.详图Free stand type 坐（落）地式Detection n.探知，发现Function n.函数Development n.发展Fixing lug n.摩耳Die n.冲模Flange n.凸缘，翼缘Difference n.不同，差异Flashing n.防水板，遮雨板E Float glass 浮法玻璃Earthquake n.地震Folded 折叠的，拦杆Earthquake load 地震荷载Force n.力，力量；v.强迫Eccentric a.偏心的Foreword n.序言Eccentrically Adv.偏心地Formula n.方程Effect v.影响GEffective a.有效的G.M.S. =galvanized mild steelElastic a.弹性的Galvanization n.镀锌Elevation n.海拨，立面Galvanize v.镀锌Engineering n.工程Glass n.玻璃Equal angle a.等边角钢Glazing n.玻璃窗，玻璃装饰Equivalent a.等于Global a.通用的,全球的,球形的Examined 审定Granite cladding 花岗岩围护，干挂石Example n.例子，样本Gravity n.重量Exposed frame a.明框Grille n.格子Exterior a.外部的Grout n.水泥浆Extrusion n.挤压Grouting （填塞的）水泥砂浆幕墙常用英语Gust n.阵风Minimum n.最小值Gutter n.天沟，排水沟Modulus n.模量Gyration n.回转，旋转Moment n.瞬间，矩H Movement capacity 变形能力Hanger system 吊挂系统Mullion n.竖框，竖料Hardware n.五金NHeight n.高度Natural a.n.自然的，Hidden frame 隐框Negative a.n.否定，负数Horizontal a.水平的Neutral a.中性的Hot-dipped zinc Galvan 热浸锌Normal a.普通的，法向的I Nos. =numbersImmediate a.当地的Nut n.坚果，螺丝帽Include v.包括PIncrease V.增加Panel n.板，仪表板Individual a.个别的Parallel a.n.v.平行Inertia n.惯性Part n.部分，局部Inertia moment 惯性矩Partial a.部分的Interior a.内部的Peak 峰值Investigate n.调查,研究Penetration n.浸透，浸入Issue n.v.发行，发布Penetration butt 对接埋入焊Imposed a.应用的，利用的Period a.句号，周期J Permissible a.允许的Joint n.连接Permit v.允许Joist n.托梁，桁Pile n.桩L Pin n.a.大头钉，栓Laminated glass 夹层玻璃Plan n.计划,平面图,设计图Lateral a.侧面的，旁边的Plastic a..塑性的，可塑的Length n.长度Plate n.盘子，金属板Linear a.线性的Podium n.矮墙，女儿墙Lips n.薄片，唇Poisson’s Ratio 泊桑比Load n.v.荷载，加载Polished glass 磨光玻璃Local a.局部的，地方性的Pre-cast 预埋，预置Long a.长的Preliminary a.初步的Louver n.百叶，百页Pressure n.v.压力，压强Lug n.耳朵Principal a.主要的M Property n.财产，性质，属性M.S.. =mild steel Purposed v.计划，打算Manufacturer n.制造高，厂商Protect v.保护Material n.材料Purpose n.目的，企图，论题Maximize v.最大化PVF2 Coating 氟碳喷涂Maximum n.最大值practice n.实行Member n.杆件QMetal n.金属Quantity n.量，数量，总数Micron n.微米RMinimize v.最小化Railing n.扶手，拦杆幕墙常用英语Ratio n.比，比率SpacingReaction n.反应，反作用Suffer Rebar =reinforce bar Stud Rectangle hollow section 矩形管Structure n.结构Reduce v.减少，缩小Structure floor level =S.F.LRefer v.提交，查阅Strut n.支柱Reference n.v.参考，引用Sub-contractor n.分包商Reflective glass 反射玻璃Submission n.递呈,提交,服从Reinforcement n.加强件，加固物Suction n.吸力Resistance v.抵抗Super-structure 主体结构Restrain n.约束Supplier n.供应商Result n.结果Supply n.v.提供，补充，替代Revision n.修订，校订Support n.v.支撑，支持RHS =rectangle hollow section Support on four sides 四边支撑Rod n.小枝，竿Support on two sides 两边支撑Roof n.屋顶Surface n.表面Rigidity n.刚性Symmetry a.对称的S TScope n.范围，广度Technical a..技术的，工业的Screw n.v.螺钉，螺旋桨，拧紧Tee n.T字形，T形物Sealant n.密封胶Temperature n.温度Self-weight 自重Tempered a.调节的，钢化的Serial n.序列，系列Tempered glass 钢化玻璃Setting block 垫块Temporary a.临时的Shape n.v.形状，定形Tensile a.拉力的，张力的Shear n.v.修剪，剪切Tension n.v.张力，拉力SHS =square hollow section Terrain n.地带，地域，范围Silicone n.硅树脂The arm of force 力臂Similar n.a.相似的，相同Thickness n.厚度Simply supported beam 简支梁Thread n.纤维Site-ground 室外地面Tile 砖，磁片Sleeve n.袖子，套筒Tinted 染色的Slope n.v.倾斜Title n.名称，标题Span n.跨度Tolerance n.宽容，公差Specification n.规格，详述Top n.顶部，上总的Spider fixing （玻璃）固定爪Torsion n.扭转，扭矩Splice Vt.n.接合,连接,结婚Total 总的，总数Square hollow section 方形管Transom n.横梁，横档Stability n.稳定性Trapezoid n.梯形，不等边四边形Stainless steel 不锈钢Triangle n.三角形Standard n.标准Type 类型，型号，打字Stiffen v.使变硬UStrength n.强度UB =universal beamStress n.压力，应力UDL =uniformly distributed loadStructural a.结构的Unequal angle n.不等边角钢幕墙常用英语Uniformly Adv.统一的，一律的Universal beam 通用梁Universal column 通用柱。

建筑五金门窗幕墙最完善中英文对照表(2500对）泊桑比Poisson’s Ratio铝板Alum. Panel铝塑材切割Cutting、milling暖通空调HV AC=Heating、Ventilation ＆Air Conditioning设置可见度Set up the visibility(玻璃）固定爪Spider fixing （胶）凝固cure（门、窗魄力外）的装饰格栅decorative sash bar（受力)临界点、相变点critical point（填塞的)水泥砂浆Grouting（与墙体)安装附件wall attachment（柱）间距紧凑close interval构件Element90度转角连接材90°Corner1秒钟峰值净压力1-sec Net External Pressure1秒钟峰值压差1-sec Peak differential Pressure1秒钟外部峰值压力1-sec peak external pressureE额定荷载rated loadH型钢H—type steel Low—E镀膜玻璃Low—E （low-emissivity ）coated glassT型螺栓T—head boltwall矮墙、女儿墙Podium安全防火隔热fire—safing insulation安全荷载safe load;safety load 安全荷载系数safety loadfactor安全帽protecting cap;safetyhelmet安全门detention/securitydoors安全系数safetyfactor/coefficient安锁冒头Lock rail安装标准installationbenchmark安装程序installationprocedure安装方法报告书installation method statement安装工程erection work安装就位erecting andsetting安装孔Pilot hole安装容差installationtolerance安装施工资格installationqualification暗铰Secret-hinge暗匣Blind pocket奥氏体Austenitic百叶（窗)louver; shutter；Persian blinds百叶、百页Louver百叶窗Jaiousie WindowVane百叶窗架Jaiousie WindowHolder百叶跨度length of thelouver百叶帘venetion blind百叶铝板aluminum louverpanel百叶式出气口louvered airoutlet百页片Blade搬运handling板、仪表板Panel板；板块board；plate；panel；slab板材plate板料Panel veneer板面上胶Surface gluing办公椅五金配件Officechair hardware accessories办公椅中管配件Officechair central tube accessories半钢化玻璃Halfstrengthened glass半钢化玻璃Heatstrengthened glass半钢化玻璃heatstrengthened glass; halfstrengthened glass半径radius;semidiameter半透明的translucent半隐框玻璃幕墙semi-exposed framing glasscurtain wall半隐框幕墙semi—exposedframing glass curtain wall棒、竿Rod保安配置Securityconfiguration包装packaging薄板Sheet薄板sheet；thin slab薄垫片Shim薄膜film;membrane薄膜玻璃film glass薄膜防水membranewaterproofing薄片Lip薄片Lip薄片、唇Lips薄片整修Veneer trimming保安配置Securityconfiguration保护（涂）层protectivecoating保温（岩）棉insulation保温板heated board保温材料insulationmaterial保温层insulating layer保温顶棚heat insulated ceiling保证（书）warranties报价bid；quote报价单quotation备注remark背板back-pan比例scale比例proportion避雷保护lightning protection避雷针Lighting protection air terminal边框outer frame边料、尾料ffcuts边缘荷载edge load边缘块edge block编号numbering；serial number变电站transformer substation变化系数variation coefficient变量Variable变形Deform变形Deformation变形deform；deformation 变形缝movement joint变形能力Movement capacity变形能力deformation capacity变硬Stiffen标称nominal标记mark/marking; indicator; label标价bid price标价单bid sheet标签label；checklist标示display标书bid标志signage 标准版本standards version标准尺寸typical dimension标准的Typical标准构件standard element标准间隔材料standardspacer material标准节点typical detail标准值characteristic value表面处理finish表面处理工具Equipmentfor surface treatment表面涂层surface coating表面压缩应力surfacecompression stress冰雪处理与缓和ice andsnow management andmitigation丙烯酸喷涂Crylic acidcoating丙烯酸喷涂Duracron波纹corrugation波纹不锈钢板corrugatedS.S。

玻璃类钢化玻璃：Tempered glass半钢化玻璃：Heat strengthened glass夹胶玻璃：Laminated glass钢化夹胶玻璃：Tempered laminated glass钢化中空玻璃：Tempered insulated glass钢化中空超白玻璃：Tempered insulated glass（low iron）钢化中空夹胶玻璃：Tempered insulated laminated glass 透明钢化单玻：Single clear tempered glass彩釉玻璃：Glass with frit/frit glass镀膜玻璃：Coated glass单片钢化玻璃：monolithic tempered glass压花玻璃:figured glass石材类：石材面板：Stone panel(黑色)大理石：（black）Marble stone(红色)花岗岩：Granite stone背栓：Back anchor光面：Polished毛面: Unpolished钢材类：（镀锌）槽钢：（Galvanized）steel channel钢角码：Steel bracket（镀锌）角钢：（Galvanized）steel angle(镀锌)钢方通：（galvanized）Steel hollow压型钢板：Pressing steel plate(镀锌)钢板：（Galvanized）Steel panel(冷弯)槽钢：(cold-formed) steel channel（镀锌）连接件：（Galvanized）steel bracket不锈钢调节螺栓: stainless steel adjusting bolt镀锌耳板：Galvanized ear plate（索）锚具：Anchorage device不锈钢拉索：Stainless steel tension cable钢销钉：Steel pin折弯钢连接件：Folded steel bracket不锈钢热轧钢板：Stainless steel hot rolled plate奥氏体不锈钢：Austenitic stainless steel不锈钢螺栓(组)：Stainless steel bolt (group)锚具：Anchorage device工字钢：I beam焊钉：Welding nail焊条：Welding rod龙骨：Framing member钢插芯：Steel sleeve钢板加强肋steel stiffener钢连接件steel bracket*图纸上如标注太长，不锈钢对应的单词（stainless steel）可以简写为：s.s. 或者S/S铝材类铝型材：Aluminum extrusion/profile/section铝单板：Aluminum panel（铝合金）横梁：（aluminum）transom（铝合金）立柱：（aluminum）mullion（铝合金）公型材：（aluminum）Male extrusions（铝合金）母型材：(Aluminum)Female extrusions(铝)副框：（aluminum）sub-frame(铝)插芯：(Aluminum) sleeve（铝合金）连接件：（aluminum）bracket4mm厚铝塑板：4mm thick composite panel made of aluminum and plastic铝通：Aluminum hollow铝合金扣板：Aluminum capping（铝合金）压板：（aluminum）pressure plate（铝合金）压块：(Aluminum) setting block（铝合金）挡板：(aluminum) baffle plate（铝合金）盖板：(aluminum) facecap（铝合金）背板：（aluminum）backpan角铝：Aluminum angle(铝)托条：(Aluminum) support plate（铝合金）格栅：（aluminum）grille（铝合金）(防水)百叶:（aluminum）(waterproof) louver铝合金封口板：Aluminum sealing plate铝合金水槽料：Aluminum gutter铝合金水槽堵头：Aluminum finish20mm厚硅酸铝板；20mm thk. aluminum silicate panel铝合金连接件aluminum bracket梭形铝合金格栅：Shuttle aluminum grille铝合金封口板aluminum sealing plate*图纸上如标注太长，铝合金对应的单词（aluminum）可以简写为：Alum.*“厚”对应的词“thick”，可简写为：“thk”螺栓类：不锈钢螺栓组：Stainless steel bolt group(M8x100)不锈钢螺栓：(M8X10) stainless steel bolt膨胀螺栓：Expansion bolt化学螺栓：Chemical bolt(不锈钢)机制螺栓：（stainless steel）Machine bolt(不锈钢)自攻自钻螺丝：（stainless steel）self-tapping and self-drilling screw 射钉：Drive pin铆钉：Rivet特制螺栓：Special bolt特制螺栓组special bolts group埋件类镀锌预埋件：Galvanized pre-embed预埋件：Pre-embedded part支腿：Supporting leg槽式埋件：Cast-in channel板式埋件：Cast-in plate后补埋件：Remedial cast-in窗类：开启窗：Openable vent执手：Handle窗台：Sill拼料：Aluminum ingredient扇料：Sash框料：Frame（铝）百叶窗：(Aluminum) Louvers排烟窗：Smoke extraction vent开启扇下扇：Openanle vent lower sash开启扇下框：Openanle vent lower frame铰链：Hinges电动开启器Electric opening device窗台板Sill plate窗台砌体墙Sill masonry铝合金托条Aluminum supporting bar开启扇上框Openanle vent upper frame开启扇上扇Openanle vent upper sash门类(门)锁：(Door) lock多点锁：Multi-point lock五金件：Hardware/ironmongery防火门：Fire rated door门轴：Door pivot擦窗机类：轨道：Track吊篮：Gondola结构标高（完成面）：Structure level建筑标高（完成面）：Building level图名类平面图：Plan立面图：Elevation剖面图：Section节点图：Detail大样图：Typical elevation/section/plan目录：Drawings list埋件图：Detail of embedded parts*节点图类的细图名称可统一简写为：Detail型材表：Material table设计总说明：General specification效果图：Rendering drawings三维透视图：3-D representations几何定位图：Geometry set out drawings加工图：Shop drawing施工图：Construction document安装图：Installation drawing竣工图：As-built drawings层数1层：1st storey2层：2nd storey3层：3rd storey4层：4th storey4层往上，每层的书写方式是在层数的阿拉伯数字后加th即可，如：10层：10th storey 避难层：Refuge storey图例：Legend平面索引：Key plan表面处理无机富锌涂料：Inorganic zinc-rich coating电泳涂漆：Electrophoretic finishing(热浸)镀锌：(Hot dip) galvanizing氟碳喷涂：PVDF coating阳极氧化：Anodizing粉末喷涂：Powder coating其他：泡沫填充棒：Backer rod保温棉：Thermal insulation防火棉：Fire proofing insulation以上两种岩棉（保温和防火）可统一简写为：Insulation双面贴：Double-sided tape滴水孔：Weep hole泛水板、遮雨板：Flashing（不锈钢）驳接爪：（stainless steel）Spider fixing雨蓬：Canopy（玻璃/不锈钢）栏杆：(Glass/stainless steel) handrails压块：Setting block（硅酮）结构胶：Structural (silicone) sealant（硅酮）密封胶：Weatherproof (silicone) sealant防火密封胶：Fire retardant sealant 或者fireproof sealant钢绞线：Strand复合板: Composite panel陶土板：Terracotta panel伸缩缝：Expansion joint主楼：Main building裙楼：Podium塔楼：Tower：采光顶：Skylight（铝）背板：(Aluminum) backpan室内完成面：Inside finish level窗台砌体墙：Sill masonry非承包范围/由其他单位负责：By others防噪音胶条：Acoustic gasket开启扇密封胶条(EPDM)：EPDM gasket固定玻璃密封胶条(EPDM)：EPDM gasket屋面防水：Roof waterproofing防腐蚀垫片：Anti-corrosive sheet尼龙垫片：Nylon sheet隔热块：Thermal block（钢筋）混凝土：（reinforced）concrete硅酸铝高温粘接剂：High-temperature adhesive排水线路：Weep line拉索索具调节端rigging adjusting side预应力保持装置pre-stress retaining device钢化中空夹胶彩釉玻璃Tempered Insulating Laminated fritted Glass顶棚索网幕墙大样图partial elevation for ceiling tension cable net(可简写为：partial elevation) 分格尺寸module dimension(可简写为：modul. dim.)(中间3#拉索) (3# tension calbe for middle layer)(下层2#拉索）(2# tension calbe for lower layer )主体结构：main structure不锈钢黑色防虫网：s.s.black insect net（防火棉）卡码：insulation fixer主体钢构（其他单位负责）main steelwork(by others)隔音棉acoustic insulation不锈钢排水沟stainless steel draining gutter雨蓬落水管canopy downpipe正风压：Positive wind pressure负风压：Negative wind pressure落水口：Weep hole雨棚侧面边缘线：Projection line of canopy排水槽找坡最高点：Sloping height of draining gutter分格尺寸仅供参考：Module Dimensions for reference only梭形百叶：Shuttle louvers细木工板：Block board 或laminated wood board吊顶：Ceiling防腐蚀垫片：Anti-corrosive sheet圆形内撑板：Round interior support panel圆形外夹板：Round exterior clip panelA视图：A view。