EN 1337-22004年3月ICS 91.010.30 取代：EN 1337-2:2000结构支座第2部分: 滑动元件本欧洲标准于2004年6月由CEN通过。
CEN的委员需遵守CEN/CENELEC 的内部规章，并约定本欧洲标准为国际性标准之条件，且不需作任何修改。
本欧洲标准的草案由CEN建立并发行三个官方版本(英文、法文、德文)。
CEN 委员为国际标准个体所组成，包括奥地利、比利时、塞浦路斯、丹麦、捷克、爱沙尼亚、匈牙利、芬兰、法国、德国、希腊、冰岛、爱尔兰、意大利、拉托维亚、立陶宛、卢森堡、马耳他、荷兰、挪威、波兰葡萄牙、斯洛伐克、斯洛文尼亚、西班牙、瑞典、瑞士及联合王国目录前言说明1 范围2 标准的参考文献3 术语，定义，符号和缩写词4 性能要求5 材料6 设计要求7 制造装配和公差8 设计的达标评估9 安装10 使用过程中的检测的重点附录 A (增进了解篇) 简化的滑动元件附录 B (增进了解篇) PTFE板凹孔的摩擦系数附录 C (增进了解篇) 安装在混凝土上的锚锭板形变的计算方法附录 D (规范篇) 摩擦力的测试方法附录 E (规范篇) 锚锭板表面的铬硬度-孔隙度试剂试验附录 F (规范篇) 电镀表面厚度测定附录G (规范篇) 润滑油的油剂单独试验附录H (规范篇) 润滑油的氧化稳定性附录J (规范篇) 不锈钢附着板–实验室剪切力测试附录K (规范篇) 工厂生产管理(FPC)附录L (增进了解篇) 检验测试参考书目前言此文献（EN 1337-2：2004）由CEN/TC167盆式支座技术委员会制定，其秘书工作由UNI承担。
此文献（EN 1337-2：2004）取代EN 1337-2:2000。
此欧洲标准EN 1337包括以下11个部分：第一篇一般设计通则第二篇滑动元件第三篇橡胶支座第四篇滚轴支座第五篇盆式支座第六篇摇轴支座第七篇球型和圆柱型PTFE 支座第八篇导向型支座和固定支座第九篇保护第十篇检查和保养第十一篇运输，储存和安装附录A, B, C 和L是增进了解篇附录D, E, F, G, H, J 和K是规范篇。
![[整理]-61标准物数据表.](https://imgs-1438308264.cos.ap-hongkong.myqcloud.com/00178337bed5b9f3f90f1c41.webp)
Chemlok® 6108 Technical Data SheetChemlok® 6108 is a covercoat used to affix a variety of elastomers to various metals. It is composed of a mixture of polymers, organic compounds and mineral fillers dissolved or dispersed in an organic solvent system. Chemlok 6108 is a non-chlorinated solvent surface treatment that provides strong resistance to harsh environments. In some applications, it may be used as a one-coat.Features and Benefits:Versatile – affixes a variety of elastomers and metals when used in combination with Chemlok 205 or 207.Non-Chlorinated Solvent System – suitable for solvent incineration.Environmentally Resistant – provides superior resistance to heat, oils and salt spray. Elastomers:• Natural Rubber (NR) • Polychloroprene (CR)• Polyisoprene (IR) • Nitrile (NBR)• Styrene-butadiene (SBR) • Butyl (IIR)• Polybutadiene (BR) • EPDM Polymers• Chlorinated Polyethylene (CPE)• Chlorosulfonated Polyethylene (CSM)Application:Surface Preparation – Thoroughly clean metal surfaces prior to primer application. Remove protective oils, cutting oils and greases by solvent degreasing or alkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.Allow primer to thoroughly dry before applying Chemlok 6108.For further detailed information on surface preparation of specific substrates, refer to Chemlok application guide. Mixing – Thoroughly stir Chemlok 6108 before use, and agitate sufficiently during use to keep dispersed solids uniformly suspended. If dilution is needed, use xylene or toluene. Note proper dilution for the various application methods is best achieved by experience. Give careful attention to agitation since dilution will accelerate settling. Applying – Apply Chemlok 6108 by spray, brush or dip methods.Regardless of application method, the dry film thickness of Chemlok 6108 should be 17.8-25.4 micron (0.7-1.0 mil). Curing – Chemlok 6108 cures during the rubber vulcanization process.Cleanup – Use solvents such as xylene and MEK to remove Chemlok 6108 before heat is applied. Once cured, removal by solvent is not possible.Shelf Life/Storage:Shelf life is one year from date of shipment when stored by the recipient at 21-27°C (70-80°F) in original, unopened container. Do not store or use near heat, sparks or openflame.Chemlok 6108 — Technical Data SheetParker LORDEngineered Materials Group 111 LORD DriveCary, NC 27511-7923USAValues stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as Parker LORD has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Parker LORD does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.WARNING — USER RESPONSIBILITY . FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.©2021 Parker Hannifin - All Rights ReservedInformation and specifications subject to change without notice and without liability therefor. Trademarks used herein are the property of their respective owners.OD DS6010CE 07/21 Rev.2Cautionary Information:Before using this or any Parker LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Required to use under organized emissions. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.Chemlok® 6108技术说明书Chemlok® 6108作为面涂可以帮助和促进各式各样的弹性体附着至各种金属。
