RP20-2415SF中文资料

FeaturesRegulated Converter• 4:1 wide input range• 3kVAC reinforced insulation for 110Vin 2.25kVDC basic insulation for 24Vin & 48Vin • Efficiency up to 93%• No minimum load required• EN50155, IEC/EN60950-1 & UL60950-1 certifiedDescriptionThe half-brick RP100H series DC/DC converters are designed for railway rolling stock and high voltage battery applications. Each series has three 4:1 input voltage range options to cover all input voltages from 9VDC up to 160VDC with isolated and regulated 5V to 48VDC outputs. The converters have high efficiencies and metal base-RP100H-RW DC/DC Converter100 Watt Half BrickEN50155 certifiedIEC/EN60950-1 certified UL60950-1 certifiedE196683RP100H-2415SRW 9-36 15 6700 4601 100 91 4460RP100H-2424SRW 9-36 24 4200 4666 101 90 1750RP100H-2448SRW 9-36 48 2100 4666 101 90 430RP100H-4805SRW 16.5-75 5 20000 2240 100 93 40000RP100H-4812SRW 16.5-75 12 8400 2333 101 90 7000RP100H-4815SRW 16.5-75 15 6700 2300 100 91 4460RP100H-4824SRW 16.5-75 24 4200 2333 101 90 1750RP100H-4848SRW 16.5-75 48 2100 2307 101 90 430RP100H-11005SRW 43-160 5 20000 1010 100 93 40000RP100H-11012SRW 43-160 12 8400 1018 101 90 7000RP100H-11015SRW 43-160 15 6700 1015 100 91 4460RP100H-11024SRW 43-160 24 4200 1018 101 90 1750RP100H-11048SRW 43-160 48 2100 1007 101 90 430Ordering ExamplesRP100H-2405SRW/N = 24V Input, 5V Output, Single, Neg. CTRL function RP100H-11012SRW/P = 110V Input, 12V Output, Single, Pos. CTRL functionRP100H-2405SRW/N-HC = 24V Input, 5V Output, Single, Neg. CTRL function, premounted Heat-sinkModel NumberingInput Voltage Output VoltageS ingleRP100H-__ __SRW/_ _Notes:Note2: standard part is with suffix “P” for positive logic (1=ON, 0=OFF) or add suffix “N” instead for negative logic (0=ON, 1=OFF) Note3: add suffix “-HC” for premounted Heat-sink CTRL Logic (2)Package (3)Notes:Note1:Efficiency is tested by nominal Vin, full load and at 25°Chttps:///pdf/Powerline_DC-DC/RSPxxx-168.pdf/eval-ref-boardsSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)Specifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)RP100H-4805SRW708090100Efficiency vs. Output CurrentPower up Start-up CharacteristicON/OFF Control Start-up Rise CharacteristicSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)Efficiency vs. Input Voltage60708090100708010090RP100H-11005SRWEfficiency vs. Output CurrentPower up Start-up CharacteristicSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)OUTPUT TRIM Typical Output Ripple and NoisePower up Start-up CharacteristicOutput Voltage TrimmingRP100H-RW converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. The values for trim resistors shown in trim tables below are according to standard E96 values; therefore, the specified voltage may slightly vary; they also can be calculated with below shown equation.TRIM DOWNTRIM UPTRIM-Sense+SenseSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)OUTPUT TRIMRP100H-xx05SRWRP100H-xx12SRWRP100H-xx15SRWRP100H-xx24SRWRP100H-xx48SRWTrim Down all Vout‘sTrim up 12345678910%Vout = 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.4 5.45 5.50Volts R 1 = 30915810578.763.453.646.440.236.533.2kOhms Trim up 12345678910%Vout =12.1212.2412.3612.4812.6012.7212.8412.9613.0813.20Volts R 1 = 88745330122618215413311810595.3kOhms Trim up 12345678910%Vout =15.1515.3015.4515.6015.7515.9016.0516.2016.3516.50Volts R 1 = 1130576383294237196169150137124kOhms Trim up 12345678910%Vout =24.2424.4824.7224.9625.2025.4425.6825.9226.1626.40Volts R U = 1870953634487392324280249226205kOhms Trim up 12345678910%Vout =48.4848.9649.4449.9250.4050.8851.3651.8452.3252.80Volts R 1 = 3830196013001000806681576511464422kOhms Trim down 12345678910%R 2 = 97.647.531.623.217.814.712.110.59.098.06kOhms Trim down 11121314151617181920%R 2 =7.156.345.765.114.644.223.923.573.243.01kOhmsTrim CalculationVout = Output VoltageR 1 =100*Vout+D Vout * Vout)- (100+2D Vout) k Ω D Vout = Output Voltage Trim in %1.225*D Vout D VoutR1 =trim up resistorR2 = trim down resistor R 2 = 100 - 2 k ΩD Vout Practical Example:Trim Up:Vout = 5V, D Vout = 10% (5.5V)R 1 =100*Vout+D Vout * Vout) - (100+2D Vout) k Ω = 100*5 +10*5 - 100+2*10= 44.89 - 12 = 32.9k Ω 1.225*D Vout D Vout 1.225*10 10Trim down:Vout = 5V, D Vout = -10% (4.5V)R 2 = 100 - 2 k Ω = 100 - 2 = 8.06k ΩD Vout 10Specifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)REGULATIONSParameter Condition ValueOutput Accuracy±1.0%Line Regulation low line to high line at full load±0.1% Load Regulation0% to 100% load0.1% Transient Response25% load step change200µs typ.; 250µs max.Transient Response to Dynamic Load Change from 100% to 75% to 100% of Full Load at nom.VinRP100H-4805SRWRP100H-2405SRWRP100H-11005SRWSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)ENVIRONMENTALParameterCondition ValueOperating Case Temperature Range refer to derating graphMaximum Case Temperature 105°CTemperature Coefficient ±0.02%/°C max.Thermal Impedance vertical direction by natural convection (0.1m/s) without Heat-sink vertical direction by natural convection (0.1m/s) with Heat-sink6.7°C/W 4.7°C/W Operating Humidity 5% - 95% RHPollution Degree PD2Shock according to EN61373 standard Thermal Shock according to MIL-STD-810F standardVibrationaccording to EN61373 standardFire protection on railway vehicles according to EN45545-2, 2013 standardMTBFaccording to MIL-HDBK-217F standard, 25°C408.7 x 103 hoursPROTECTIONSParameterConditionValueShort Circuit Protection (SCP)below 100m Ωcontinuous, automatic recovery Over Voltage Protection (OVP)% of nom. Vout115%-130%, Hiccup Mode Over Load Protection (OLP)% Iout rated24Vin, 48Vin 110Vin120%-150%, Hiccup Mode 150% typ., Hiccup ModeOver Temperature Protection (OTP)+110°C to +120°C Isolation Voltage110VinI/P to O/P I/P or O/P to Case 3kVAC/1minute 1.5kVAC/1minute 24Vin, 48VinI/P to O/P I/P or O/P to Case2.25kVDC/1minute 1.6kVDC/1minuteIsolation Resistance 500 VDC1G Ω min.Isolation Capacitance 2500pF max.Isolation Grade110 Vin 24Vin, 48Vin reinforced insulationbasic insulationThermal CalculationNotes:Note4: Refer to local wiring regulations if input over-current protection is also required. Recommended fuse: T35A slow blow.R thcase-ambient = 6.7°C/W (vertical) T case = Case Temperature R thcase-ambientHC = 4.7°C/W (vertical) T ambient = Environment Temperature P dissipation = Internal lossesR thcase-ambient = T case - T ambientP IN = Input PowerP dissipationP OUT = Output Power h = Efficiency under given Operating ConditionsP dissipation = P IN - P OUT = P OUTapp- P OUTapp R thcase-ambient = Thermal Impedance h Practical Example:Take the RP100H-2405SRW with 9V input Voltage and 50% load. What is the maximum ambient operating temperature? Use converter vertical in application without airflow.Eff min = 91% @ V nomP OUT = 100W P OUTapp = 100 x 0.5 = 50W h = 91% (Efficiency vs. Load Graph)without Heat-sink with Heat-sinkR th = T casemax - T amb --> 6.7°C/W = 105-T amb R thHC = T casemax - T amb--> 4.7°C/W = 105-T amb P dissipation 4.95W P dissipation4.95W T amb = 72°C T ambHC = 82°CSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)Specifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)DC/DC ConverterSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)RP100H-RWSeriesConducted Emission EN55022 Class AConducted Emission EN55022 Class AC4C5C6C7C8Shield PlaneL1C18+V INEMI Filtering according to EN55022/11 Class A and EN50121-1 (110Vin)DC/DC ConverterSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)RP100H-RWSeriescontinued on next pageEMI Filtering according to EN55022/11 Class B (24Vin and 48Vin)Shield Plane100-110xxSRW, Class BNNC6C9C8C3C4CaseL2C7C19C20Shield PlaneC12C13C14C10C11C16C2C4L1L2C5C8C6C7C11C3Conducted Emission EN55022 Class ADC/DC ConverterSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)RP100H-RWSeriesEMI Filtering according to EN55022/11 Class B (110Vin)C8Shield PlaneShield PlaneC9C1C2C3C11C12C10CaseL1C4C5C8C13C14C17C9C19C3C4L1L2C12C10C11C15C15Shield PlaneC9C10C12Conducted Emission EN55022 Class BSpecifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)Specifications (measured @Ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted)The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorizeduse of RECOM products in such safety-critical applications.PACKAGING INFORMATIONParameterTypeValuePackaging Dimension traywithout Heat-sink with Heat-sink157.0 x 88.0 x 12.8mm 157.0 x 88.0 x 24.8mmPackaging Quantity 2pcs.Storage Temperature Range -55°C to +125°C Storage Humidity5% - 95% RH。

RP20-S_DFW Series
Class A Class A Perf. Critera B Perf. Critera A Perf. Critera B Perf. Critera B Perf. Critera A MIL-STD-810D 10-55Hz, 10G, 30 Min. along X, Y and Z 5% to 95% RH Bellcore-TR-NWT-000332 2350 x 103 hours
Derating Graph (Ambient Temperature)
RP20-4805SFW
Derating graphs are valid only for the shown part numbers. If you need detailed derating information about a part number not shown here please contact our technical customer support at info@recom-development.at
Features
Regulated Converters
Rev.
Description
● ● ● ● ● ● ● ●
4:1 Wide Input Voltage Range 20 Watts Regulated Output Power 1.6kVDC Isolation Over Current and Over Voltage Protection Six-Sided Shield No Derating to 63°C Standard 2” x 1” Package and Pinning Efficiency to 86 %

Input Filter Input Surge Voltage (100 ms max.)
Input Reflected Ripple (nominal Vin and full load) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see note 7) (Positive logic)
RP15-4805SF
125 100 75 Output Power (%) 50 25 50 60 70 Ambient Temperature Range (°C) 0 -40 -25 -10 0 80 90 100
Output Power (%)
Natural Convection
75 50 25
RP15-S_DF Series
±1% 10% of FL ±1% ±1% ±2% ±5% 50mVp-p 75mVp-p ±0.02%/°C, max. 500µS 3.9V 6.2V 15V 18V 150% typ Hiccup, automatic recovery see „Selection Guide“ table 1.600VDC min. 109 Ω min. 300pF max. Single Dual 500kHz typ. 300kHz typ. UL 1950, EN60950 -40°C to +85°C(with derating) +100°C -55°C to +105°C Natural convection Natural convection with Heat Sink 12°C/Watt 10°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel-Coated copper Non-conductive black plastic Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 continued on next page

RP40-11012DFR/P RP40-11024DFR/N-HC RP40-2405SFR/P RP40-2412SFR/N-HCRP40-4805SFR/P-HCFeaturesRegulated Converters• Wide 4:1 Input Voltage Range• 1.6kVDC Isolation for 24Vin and 48Vin, 3kVDC Isolation for 110Vin • Efficiency up to 92%• Six-Sided Continuous Shield• UL60950-1 AM2 Certified, EN50155 CertifiedPD-1REV.: 0/2016DC/DC Converter3 YE A Rw ar r a n t y3DescriptionThe RP40-FR series wide range input DC/DC converters have been especially designed for railway applications and are EN50155 certified. They are also pending to UL60950-1 and cUL 60950-1, this makes them ideal for all high input voltage telecom and industrial applications where approved safety standards are required.40 Watt2“ x 1“Single & Dual OutputRP40-FR Selection GuidePart Number Input Output Output Input (1) Efficiency (1)Max. Capacitive Voltage Range Voltage Current Current typ. Load (2) [VDC] [VDC] [mA] [mA] [%] [µF]RP40-243.3SFR (3,4)9-36 3.3 10000 1528 90 26600RP40-2405SFR (3,4) 9-36 5 8000 1832 91 20000RP40-2412SFR (3,4)9-36 12 3333 1811 92 3900RP40-2415SFR (3,4) 9-36 15 2666 1811 92 2600RP40-2424SFR (3,4)9-36 24 1666 1831 91 1300RP40-483.3SFR (3,4) 18-75 3.3 10000 764 90 26600RP40-4805SFR (3,4)18-75 5 8000 916 91 20000RP40-4812SFR (3,4) 18-75 12 3333 906 92 3900RP40-4815SFR (3,4)18-75 15 2666 906 92 2600RP40-4824SFR (3,4) 18-75 24 1666 915 91 1300 RP40-1103.3SFR (3,4) 43-160 3.3 10000 341 88 26600RP40-11005SFR (3,4) 43-160 5 8000 409 89 20000RP40-11012SFR (3,4)43-160 12 3333 402 90.5 3900RP40-11015SFR (3,4) 43-160 15 2666 400 91 2600RP40-11024SFR (3,4)43-160 24 1666 404 90 1300RP40-2412DFR (3,4) 9-36 ±12 ±1666 926 90 ±2600RP40-2415DFR (3,4)9-36 ±15 ±1333 926 90 ±1600RP40-2424DFR (3,4) 9-36 ±24 ±833 915 91 ±650RP40-4812DFR (3,4) 18-75 ±12 ±1666 463 90 ±2600RP40-4815DFR (3,4) 18-75 ±15 ±1333 370 90 ±1600RP40-4824DFR (3,4)18-75 ±24 ±833 286 91 ±650RP40-11012DFR (3,4) 43-160 ±12 ±1666 204 89 ±2600RP40-11015DFR (3,4) 43-160 ±15 ±1333 204 89 ±1600RP40-11024DFR (3,4)43-160 ±24 ±833 200 91 ±650Model NumberingOrdering ExamplesRP40-2405SFR/P = 24V Input, 5V Output, Positive Logic CTRL pin and Trim pin fitted RP40-2415SFR/N = 24V Input, 15V Output, Negative Logic CTRL pin and Trim pin fitted Input Voltage Output Voltage S ingle or D ualRP40-__ __ _FR/_ _Notes:Note1: Values at nominal input voltage and full load Note2: Test by minimum Vin and constant resistor load.EN50155 Certified UL60950-1 AM2 CertifiedE196683Notes:Note3: standard part is with suffix “P” for positive logic (1=ON, 0=OFF) and trim pin or add suffix “N” instead for negative logic (0=ON, 1=OFF) and trim pin Note4: add suffix “-HC” for premounted Heat-sink with clampsPackage (4)CTRL Logic (3)PD-2REV.: 0/2016DC/DC Conver terRP40-FRSeriesSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)DC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)REGULATIONSParameterConditionValueOutput Voltage Accuracy full load and nominal Vin±1%Voltage Adjustability Single3.3Vout, 5 Vout, 12Vout 15Vout, 24Vout ±10%-10% to +20%Line Voltage Regulation low line to high line at full load ±0.2%Load Voltage Regulation 0% to 100% loadSingle Dual±0.5%±1.0%Cross Regulationasymmetrical 25%<>100% load±5%Transient Response recovery time25% load step change 250µs typ.continued on next pageRP40-FRSeriesPD-3REV.: 0/PD-4REV.: 0/2016DC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FRSeriesDC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FRSeriesPD-5REV.: 0/ Trim up 12345678910%Vout =15.1515.315.4515.6015.7515.9016.0516.2016.3516.50Volts R U = 419.81199.91126.6089.9567.9653.3042.8334.9828.8723.98KOhms Trim up 11121314151617181920%Vout = 16.65016.80016.95017.10017.25017.40017.55017.70017.85018.000Volts R U = 19.9816.6513.8311.429.327.49 5.87 4.43 3.15 1.99KOhms Trim down 12345678910%Vout = 14.85014.70014.55014.40014.25014.00013.75013.50013.25013.000Volts R D =284.89128.6876.6150.5834.9624.5517.1111.537.193.72KOhmsTrim up 12345678910%Vout =24.24024.48024.72024.96025.20025.44025.68025.92026.16026.400Volts R U = 1275.2606.60383.73272.30205.44160.87129.03105.1586.5871.72KOhms Trim up 11121314151617181920%Vout = 26.64026.88027.12027.36027.60027.84028.08028.32028.56028.800Volts R U = 59.5649.4340.8633.5127.1521.5716.6612.298.38 4.86KOhms Trim down 12345678910%Vout = 23.76023.52023.28023.04022.80022.56022.32022.08021.84021.600Volts R D =838.15376.78222.98146.0999.9569.1947.2230.7417.937.68KOhmsRP40-xx15SFRRP40-xx24SFRPROTECTIONSParameterCondition ValueShort Circuit Protection (SCP)continuous, automatic recoveryOver Voltage Protection (OVP)Zener Diode Clamp 3.3Vout 5Vout12Vout15Vout 24Vout3.9VDC 6.2VDC 15VDC 20VDC 30VDCOver Load Protection (OLP)% Iout rated150% typ., Hiccup ModeOver Temperature Protection (OTP)115°C Isolation Voltage24Vin, 48VinI/P to O/PI/P to O/P to Case 1.6kVDC 1.6kVDC 110VinI/P to O/PI/P to O/P to Case3kVDC 1.6kVDC Isolation Resistance 500VDC1G Ω min.Isolation Capacitance1500pF max.Notes:Note6: This power module is not internally fused. An input line fuse must always be used.SAFETY AND CERTIFICATIONSCertificate Type (Safety)Report / File NumberStandard Information Technology Equipment, General Requirements for Safety E196683UL60950-1, 2nd Edition AM:2, 2014CSA C22.2 No. 60950-1-07Railway Applications - Electrical Equipment used on rolling stock15A100702E-CEN50155, 2007EMI ComplianceConditionStandard / CriterionIndustrial, scientific and medical equipment - Radio frequency disturbance characteristics - Limits and methods of measurement (8)with external filter EN50121-3-2, Class A EN55011, Class A or B ESD Electrostatic discharge immunity testRadiated, radio-frequency, electromagnetic field immunity test Fast Transient and Burst Immunity (9)Surge Immunity (9)Immunity to conducted disturbances, induced by radio-frequency fields Power Magnetic Field ImmunityAir ±8kV and Contact ±6kV20 V/m ±2kV ±2kV 10 Vr.m.s100A/m continuous; 1000A/m 1sEN61000-4-2, Criteria A EN61000-4-3, Criteria A EN61000-4-4, Criteria A EN61000-4-5, Criteria A EN61000-4-6, Criteria A EN61000-4-8, Criteria Acontinued on next pagePD-6REV.: 0/2016DC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FRSeriesDC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FRSeriesPD-7REV.: 0/2016PD-8REV.: 0/2016DC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FRSeriesDC/DC Conver terSpecifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)RP40-FR SeriesPD-9REV.: 0/2016 Specifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)DIMENSIONS and PHYSICAL CHARACTERISTICSParameter Type ValueMaterialCaseBasePottingCopper Alloy CuZn33FR4 PCBSilicone (UL94V-0)Packaging Dimension (LxWxH)without Heat-sinkwith Heat-sink50.8 x 25.4 x 10.2mm56.8 x 25.4 x 16.8mmPackaging Weightwithout Heat-sinkwith Heat-sink32g43g continued on next pagePD-10REV.: 0/PACKAGING INFORMATIONParameterTypeValuePackaging Quantity without Heat-sink with Heat-sink Tube Tray9pcs 20pcsStorage Temperature Range -55°C to +125°C Storage Humidity5% - 95% RHThe product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.25.4Specifications (measured @ ta = 25°C, nominal input voltage, full load otherwise noted)PD-11REV.: 0/RP40-4815SFR/N RP40-4815SFR/N-RP40-483.3SFR/NHCRP40-11012DFR/P RP40-11024DFR/N-HC RP40-2405SFR/P RP40-2412SFR/N-HCRP40-4805SFR/P-HC。