船舶名词
- 格式:doc
- 大小:151.00 KB
- 文档页数:5
船舶结构部件名称以及相关名词1.1船长1)总长Loa:length of overall2)垂线间长Lbp:length between perpendiculars 3)登记船长L:registered length4)干舷长Lf:freeboard length5)船舶分舱长度LS:subdivision length6)艉垂线:aft perpendicular7)艏垂线:forward perpendicular8)后端点:aft end point9)挪威规范,英国规范:Oslo Rules, UK Rules 10)前端点:fore end point11)美国规范:USA Rules12)艏楼甲板:F’cle Dk13)日本规范: Japanese Rules14)艏柱:stem15)水线长:length of water line16)干舷长前端点: forward end of freeboard length 1.2 船宽1)登记船宽B:registered breadth2)上甲板 Upp Deck3)角隅圆弧的断点:termination of corner radius 4)干舷船宽Bf : breadth of ship for freeboard5)分舱船宽Bs : subdivision breadth of ship1.3 型深(D)depth1.4 吃水d: draught or draft1.5 干舷: freeboard1.6 吨位及舱容 tonnage and cargo capacity总吨 gross tonnage 净吨 net tonnage苏伊士运河吨位 Suez Canal tonnage巴拿马运河吨位 Panama Canal tonnage排水量 displacement载重吨 deadweight国家吨位 national tonnage国际吨位 international tonnage包装货物舱容 bale capacity谷物舱容 grain capacity外板 shell plating 护肋材 sparring谷物容积限度 grain capacity捆包容积限度 limit of bale capacityg表示谷物容积 g indicates grain capacity b表示捆包容积 b indicates bale capacity 底部垫木 bottom ceiling1.7船速 speed1.8 船型系数 block coefficient细长型 fine form 肥大型 full form 方形系数block coefficient (Cb)中横剖面系数 midship coefficient (Cm)棱形系数 prismatic coefficient (Cp)水线面系数 water plane coefficient (Cw)1.9描述船舶动态及静态的词汇 terms to describe the dynamic[dai’nAmik] conditions and static positions纵倾trim 艉翘 trim by stern 艏翘 trim by head无纵倾状态 even keel (non-trimmed condition)横倾 heel or list 船体运动 ship motion横摇 rolling纵摇 pitching艏摇 yawing垂荡 heaving横荡 swaying纵荡 surging1.10描述船体构件受力及变形的词汇 describe the movement of hull structural member弯曲 bending 扭曲 twisting 屈曲buckling振动 vibration 剪切 sheering 横摇rolling 强摇 racking1.11其他基本词汇 (1)1)左舷 port side 2) 右舷 starboard side3) 纵向 longitudinal 4) 横向 transverse5) 水平 horizontal 6) 垂直 vertical 7) 中心线 centre line (CL & )8) 舯 midship or amidships (expressed by symbol )9) 船中区域 midship part (0.4L ~ 0.5L)10) 船首 bow 11) 艏柱 stem 12) 艏部 bow part or fore part13) 艏垂线 fore perpendicular (FP)14) 艉柱 stern 15) 艉部stern part or aft part16) 艉垂线 aft perpendicular (AP)17) 尾端 ends: these normally signify the end parts of the hull of a ship with 0.1L通常是指自船尾端始的0.1L的范围18) 基线 base line (BL): normally the keel line 通常是指龙骨线19) 肋骨间距 frame space 20) 肋骨线 frame line21) 船体围长 girth length: the length measured at the transverse section of the hull of a ship from gunnel to gunnel 在船体横截面上从一侧的船舷上沿量取到另一侧的船舷上沿的距离22) 龙骨上面 top of keel 23) 折角线 knuckle line (KL) 24) 折角点 knuckle point25) 舷弧 sheer 26) 艏舷弧 fore sheer 27) 艉舷弧 aft sheer 28) 梁拱camber29)甲板内倾 tumble home 30) 外飘 flare31)舭部升高 rise of floor 32)平行部 parallel part1.12其他基本词汇(2)1) 船桥甲板上缘 top of bridge deck beam 2) 船桥楼外缘 outline of bridge enclosure 3) 上甲板梁上缘top of upper deck beam 4)梁拱 camber5) 主甲板的内倾tumble home at upper deck6) 船桥甲板的内倾 tumble home at bridge deck7) 上甲板边 upper deck at side 8) 船中心线 centre line of ship9) 舭部 bilge part 10) 平板龙骨的一半 half-side dimension of flat portion at keel11) 船中船桥甲板的型深 moulded depth to bridge deck12) 船中主甲板处的型深 moulded depth to upper deck13) 船中型吃水 moulded draught1.13 线型 lines1) 横剖线图 body plan 2) 纵剖线图 profile or sheer plan 3)半宽图水线 half-breadth plan 1.14其他图纸文件 other plans and documents1) 除线型图之外,下列图纸被称为关键图(key plans):总体布置图 general arrangement 中横剖面图 midship section钢材构造图 construction profile 外板展开图 shell expansion2) 其他关键图以外的船体图纸被称为船厂图 (yard plan):(1) 船体方面艏柱、艉柱、螺旋桨柱和舵结构 stem, stern frame, propeller post and rudder甲板结构图 deck plans 单底、双底结构图 single bottom and double bottom水密和油密舱壁结构图 watertight and oil tight bulkheads上层建筑端壁图 superstructure end bulkhead船首、船尾、船底部抗拍击结构图 arrangement to resist panting in both peaks and their vicinity [vi’siniti] 邻近, 接近支柱和甲板纵桁图 pillars and deck girders 轴隧图 shaft tunnels锅炉、主机、推力轴承、中间轴承、发电机和其它重要辅机基座图Seating of boiler, engine, thrust and plummer blocks dynamos 发电机机舱棚图 machinery casings长甲板室结构图 long deckhouse桅杆、桅室和绞车平台结构图 masts and mast houses and winch platforms泵布置图 pumping arrangements甲板装原木时绑扎装置布置图 timber deck cargo security arrangements防火构造图 construction for fire protection消防布置图 plans showing fire extinguishing arrangement逃生路径布置图 plans showing escape routes舱室路径图 plans showing arrangement for access of tank and space(2) 轮机方面机器处所布置图 machinery arrangement of machinery space船内通讯系统图 diagram for internal communication system主、辅机图 main and auxiliary engines动力传动齿轮、轴系及螺旋桨图 power transmission gears, shafting and propellers锅炉及压力容器图 boiler and pressure vessel辅机和管系图 auxiliary machinery and piping操舵装置图 steering gear自动控制及遥控装置图 automatic and remote controls备件 spare part 电气装置 electrical installations 船桥视界 navigation bridge visibility (3) 其他图纸文件船体轮机设计说明书 specifications for hull and machinery船中横剖面模数计算书 calculation sheets for minimum athwartship (横越) section modulus (模数) in way of the midship part防腐式样书 corrosion prevention scheme 稳性计算书 stability calculation sheets破舱稳性计算书 damage stability calculation sheets装载手册 loading manual 绑扎手册 security manual1.15 静水力曲线 hydrostatic curves浮心距基线高度 centre of buoyancy above base line (KB)浮心距船中 centre of buoyancy from midship (B)漂心距船中centre of floatation from midship (F)每厘米吃水吨数 tons per one centimeter immersion (TPC)每厘米纵倾力矩 moment to change one centimeter (CTM)水线系数 water plane coefficient (Cw)纵稳心距基线高 longitudinal metacentre above base line (LKM)横稳心距基线高 transverse metacentre above base line (KM)棱形系数prismatic [priz’mAtik] co efficient (Cp)垂直棱形系数 vertical prismatic coefficient (Cvp)方形系数 block coefficient (Cb)型排水量 displacement in tons excluding appendages (附件,附属物)总排水量 displacement in tons including appendages船体湿表面面积 wetted surface area (W.S.)1.16 稳性 stability1)静态稳性 intact stability 2)动态稳性 dynamic stability3)稳性判据 stability criteria (标准) 4)稳性曲线 stability curves5)倾斜试验 inclining test 6)重心高度 KG (height of centre of gravity)7)稳心高度 KM (height of metacentre)8)初稳性高度 GM 9)静稳性力臂 GZ10)自由液面的影响 free water effect11)大倾角稳性 stability at a large inclination angle12)稳性十字曲线 cross curves of stability13)纵向稳性 longitudinal stability 14)横向稳性 transverse stability 15)破舱稳性 damage stability 16)浸水计算 flooding calculation 17)浸水概率 flooding probability 18)分舱 compartment19)生存条件 survival requirement 20)最终状态 final stage21)生存概率 survival probability 22)分舱指数 subdivision index 23)处所渗透率 permeability of a space24)许用GM0曲线 permissible GM0 curve1.17 波浪 wave斯托克波 stokes wave 正弦波 sine wave 摆动波 trochoidal wave船行波 wave generated by ship sailing 散波 divergent wave船尾横波 stern transverse eave 船首横波 bow transverse wave1.18 船体强度 strength of ship船体垂向弯曲最终强度 vertical bending ultimate strength船体梁强度 hull girder strength 纵向强度 longitudinal strength纵向弯距 longitudinal bending moment 剪切力 sheering force中拱 hogging 中垂 sagging静水弯距 longitudinal bending moment in still water (Ms)波浪弯矩 Mw(+) and Mw (-) wave induced longitudinal bending moment 横向强度 transverse strength 扭转强度 twisting strength局部强度 local strength 失稳强度 buckling strength受压失稳强度 compressive buckling strength剪切失稳强度 sheer buckling strength直接强度计算/分析 direct strength calculation / analyzing疲劳强度 fatigue strength疲劳强度解析、评价 fatigue strength anlyze, assessment应力集中 stress concentration波浪周期 wave period 随浪 following wave 顶浪 heading sea 横浪 beam wave 波浪载荷 wave load 垂向波浪弯距 vertical wave bending moment波浪变动压 hydrodynamic (水力,流体动力学)pressure舱室内压 internal pressure 许用应力 allowable stress最小弯距 Wmin 剖面模数 section modulus惯性矩 moment of inertia强度连续性 continuity of strength 板架、板单元 plate panel1.19 船体尺寸限制Panama 圣。
1 船舶辅机marine auxiliary machinery船上除主机、主锅炉以外所有机械设备的统称2 机舱辅机engine-room auxiliary machine装设于船舱内,除甲板机械以外为主机及其他系统服务的机械3 甲板机械deck machinery一般装置在甲板上,为船舶航行、系泊、装卸及拖曳等服务的机械。
如舵机、锚机、绞缆机、起货机、起艇机等4 船用泵marine pump,ship’s pump符合船舶规范规定或船用技术条件要求的各种供船舶使用的泵的统称5 主泵main pump主要和经常使用的泵。
如主给水泵、主冷却水泵等6 辅泵auxiliary pump,donkey pump作为待用和起辅助作用的泵。
如辅给水泵、辅冷却水泵等7 值班泵duty pump,service pump工作中的泵8 待用泵standby pump作好起动准备,随时可以投入使用的泵。
一般与值班泵轮换使用9 起动用泵starting up pump供起动时使用的泵,如向锅炉注水的泵、起动时用的滑油泵等10 首尖舱泵forepeak pump抽送首尖舱积水、具有独立管系的泵11 减摇泵anti-roll pump用于减摇水舱系统的泵12 纵倾平衡泵trim (ming)pump抽送舱柜中的水或油类以调节船舶纵倾平衡的泵13 横倾平衡泵list pump将水或油从左或右舷液舱抽送到右或左舷液舱以调节船舶横倾平衡的泵14 甲板冲洗泵deck wash pump,flushing pump抽送冲洗甲板用水的泵15 停泊泵port(duty)pump,harbor pump16 舱底泵bilge pump一般具有自吸能力,用以将舱底水抽送到舷外的泵17 压载泵ballast pump用于压载水舱注水或排水的泵18 专用清洁压载泵clean(permanent water)ballast pump油船上抽送专用清洁压载水的泵19 洗舱泵butterworth pump,tank cleaning pump油船上抽送清洗油舱用水的泵20 清舱泵cargo oil stripping pump船上抽送油舱中残余剩油的泵21 总用泵general service pump作日常杂用的泵,也常作为其他专用泵的待用泵22 卫生泵sanitary pump抽送卫生用水的泵23 消防泵fire pump抽送消防用水的泵24 应急消防泵emergency fire pump25 可移式消防泵机组portable fire(fighting)unit 由独立动力机如汽油机、柴油机等驱动的,非固定安装并可用人力搬移的消防泵机组26 泡沫原液泵concentrate pump泡沫灭火系统中用作抽送泡沫原液的泵27 泡沫液循环泵泡沫灭火系统中将泡沫液自贮存舱吸出并使泡沫液与水混合成泡沫混合液的泵28 粪便泵sewage pump抽送粪便等污物的泵29 热水循环泵hot water circulating pump生活用热水系统中,使热水通过热水器循环,以防止热水冷却的泵30 淡水泵fresh water pump抽送淡水的泵31 海水泵sea-water pump抽送海水的泵32 饮水泵drinking water pump,(portable water pump)抽送饮用的泵33 疏水泵drainage pump排去船上积水的泵34 救助泵salvage pump打捞或救助用的泵35 液货泵liquid cargo pump抽送液体货物的泵36 货油泵cargo (oil)pump油船上抽送货油的泵,有时亦兼作压载泵37 泥泵dredging pump挖泥船上抽送泥浆的泵38 增压泵booster pump,boosting pump产生一定压力,为另一泵建立吸入条件的泵。
定义航行或停泊于水域的运输或作业工具,按不同的使用要求而具有不同的技术性能,装备和结构型式。
构成船舶是由许多部分构成的.按各部分的作用和用途,可综合归纳为船体,船舶动力装置,船舶舾装等3大部分.船体:船体是船舶的基本部分,可分为主体部分和上层建筑部分.主体部分一般指上甲板以下的部分,它是由船壳(船底及船侧)和上甲板围成的具有特定形状的空心体,是保证船舶具有所需浮力,航海性能和船体强度的关键部分,一般用于布置动力装置,装载货物,储存燃油和淡水,以及布置其他各种舱室.为保障船体强度,提高船舶的抗沉性和布置各种舱室,通常设置若干强固的水密横舱壁(或同时包括纵舱壁)和内底,在主体内形成一定数量的水密舱,并根据需要加设中间甲板(一层或数层)或平台,将主体水平分隔成若干层. 上层建筑位于上甲板以上,由左,右侧壁,前,后端壁和各层甲板围成,其内部主要用于布置各种用途的舱室,如工作舱室,生活舱室,贮藏舱室,仪器设备舱室等.上层建筑的大小,层楼和型式因船舶用途和尺度而异,一般都设首楼,而上层建筑的主要部分则位于机(炉)舱区域之上.运输货物船舶的上层建筑长度较短,而客船和科学考察船的上层建筑则是很讲究的.船体结构大都用钢材,由板材和型材组合成板架结构.船舶动力装置船舶动力装置包括:推进装置——主机经减速装置,传动轴系以驱动推进器(螺旋桨是主要的型式);为推进装置的运行服务的辅助机械设备和系统,如燃油泵,滑油泵,冷却水水泵,加热器,过滤器,冷却器等;船舶电站(发电机,配电板等),它为船舶的甲板机械,机舱内的辅助机械和船上照明等提供电力;其他辅助机械和设备,如锅炉,压气机(和空气瓶),船舶各系统的泵,起重机械设备,维修机床等(它们并不全是为主机服务的).通常把主机(及锅炉)以外的机械统称为辅机.船舶舾装和其他装备:船舶舾装包括舱室内装结构(内壁,天花板,地板等),家具和生活设施(炊事,卫生等),涂装和油漆,门窗,梯和栏杆,桅杆,舱口盖等.船舶的其他装置和设备中,除推进装置外,还有:①锚设备与系泊设备;②舵设备与操舵装置;③救生设备(救生衣,救生筏,救生艇及其收放装置);④消防设备(探火和灭火设备与系统);⑤船内外通信设备(船内电话,无线电台);⑥照明设备;⑦信号设备(号灯,号旗等);⑧导航设备(雷达,各种定位仪,测探仪,计程仪等);⑨起货设备;⑩通风,空调和冷藏设备(食品库和冷藏货舱用); 海水和生活用淡水系统; 压载水系统; 液体舱的测深系统和透气系统; 舱底水疏干系统; 船舶电气设备,包括电缆,电气控制板(箱),蓄电池,变压器和变流机等.船舶设备中的照明,通信,信号,导航等设备也可归入电气设备; 其他特殊设备(依船舶的特殊需要而定).分类船舶分类方法很多,可按用途,航行状态,船体数目,推进动力,推进器等分类.按用途分类这种分类方法最常用,可分为军用和民用船舶两大类.军用船舶通常称为舰艇或军舰.其中,有直接作战能力或海域防护能力者称为战斗舰艇,如航空母舰,驱逐舰,护卫舰,导弹艇和潜艇,以及布雷,扫雷舰艇等,担负后勤保障者称为军用辅助舰艇.民用船舶指各种非军用船舶.某些小船习惯上也称为艇.民用船舶一般又分为运输船,工程船,渔船,港务船等.①运输船:用于港口之间的运输,如客船(包括渡船),货船,客货船.货船又按货物种类,运输方式和装卸方法分为:散件杂货船(统货或杂货船),集装箱船,滚装船(包括车辆渡船),散货船(多指谷物,煤,矿砂运输船),运木船,油船,液化天然气(和石油气)船,驳船,拖驳船队,顶推驳船队(分节驳)等.有的船舶能运载集装箱,矿砂,木材,谷物等多种货物,称为多用途船;有的专业船舶兼能运载石油,矿砂和其他粒状散货,称为兼用船.②工程船:如挖泥船,打桩船,起重船,打捞船,布缆船,疏浚船和炸礁船.③渔业船:如各类捕捞船(拖网渔船,围网渔船,刺网渔船,流网渔船,钓鱼船,蟹工船,捕鲸船和狩猎渔船),水产品加工船,水鲜冷藏运输船,渔政船等.④港务船:如港作拖船,引水船,航标船,港监船,供油船,供水船,消防船和交通船.⑤海难救助船.⑥海洋开发船:如海洋调查船,钻井船,多用途拖船和潜水器.按航行状态分类通常分为排水型船舶,滑行艇,水翼艇和气垫船.①排水型船舶:水面船舶航行时,重力全靠水的浮力来支承,绝大多数船舶属于此类.②滑行艇:高速航行时,仅部分艇底接触水面,重力大部分靠作用于艇底的动压力支承.③水翼艇:船体下装有水翼,高速航行时靠水翼的升力使船体部分或全部离开水面.④气垫船:靠向艇底不断输送高于大气压力的空气把艇体全部或部分升起,以降低水阻力而高速航行.气垫船又分全垫式和侧壁式两种.按船体数目分类分为单体船(绝大多数船舶属此类)和多体船.在多体船型中双体船较为多见.双体船具有二个相同的片体(成一定距离并列),在距水面一定高度处用连接桥连接成一体,多用作客船和车辆渡船,具有甲板面积大,装载地位多和稳性好的优点.为改善双体船的耐波性和快速性,又有一种小水线面船,片体自水面下一定高度起缩小为流线型,狭窄柱体伸出水面与连接桥相接.按推进动力分类:可分为机动船和非机动船.机动船按推进主机的类型又分为蒸汽机船(活塞式,现已淘汰),(蒸)汽轮机船,柴油机船,燃气轮机船,联合动力装置船,电力推进船,核动力船等.按推进器分类有螺旋桨船(主要型式),喷水推进船,喷气推进船,明轮船,平旋轮船等.空气螺旋桨只用于少数气垫船.按推进器数目还可分为单桨船,双桨船,三桨船等.按机舱部位分类有尾机型船(机舱在船的尾部),中机型船和中尾机型船.按主体连续甲板的层数分类有单甲板船,双甲板船,三甲板船等.按船体结构材料分类有钢船,铝合金船,木船,钢丝网水泥船,玻璃钢艇,橡皮艇,混合结构船等.主要技术特征船舶的主要技术特征有船舶排水量,船舶主尺度,船体系数,舱容和登记吨位,船体型线图,船舶总布置图,船体结构图,主要技术装备的规格等.船舶吃水、吨位和标志吃水船舶吃水:水线面与船底基平面之间的垂直距离(自平板龙骨上缘量至水面的垂直距离。
船舶英文名词船舶结构部件名称以及相关名词2014-05-13 中国海员之家1.1船长1)总长Loa:length of overall2)垂线间长Lbp:length between perpendiculars3)登记船长L:registered length4)干舷长Lf:freeboard length5)船舶分舱长度LS:subdivision length6)艉垂线:aft perpendicular7)艏垂线:forward perpendicular8)后端点:aft end point9)挪威规范,英国规范:Oslo Rules, UK Rules10)前端点:fore end point11)美国规范:USA Rules12)艏楼甲板:F’cle Dk13)日本规范: Japanese Rules14)艏柱:stem15)水线长:length of water line16)干舷长前端点: forward end of freeboard length1.2 船宽1)登记船宽B:registered breadth2)上甲板Upp Deck3)角隅圆弧的断点:termination of corner radius4)干舷船宽Bf : breadth of ship for freeboard5)分舱船宽Bs : subdivision breadth of ship1.3 型深(D)depth1.4 吃水d: draught or draft1.5 干舷: freeboard1.6 吨位及舱容tonnage and cargo capacity总吨gross tonnage 净吨net tonnage苏伊士运河吨位Suez Canal tonnage巴拿马运河吨位Panama Canal tonnage排水量displacement载重吨deadweight国家吨位national tonnage国际吨位international tonnage包装货物舱容bale capacity谷物舱容grain capacity外板shell plating 护肋材sparring谷物容积限度grain capacity捆包容积限度limit of bale capacityg表示谷物容积g indicates grain capacity b表示捆包容积b indicates bale capacity底部垫木bottom ceiling1.7船速speed1.8 船型系数block coefficient细长型fine form 肥大型full form 方形系数block coefficient (Cb)中横剖面系数midship coefficient (Cm)棱形系数prismatic coefficient (Cp)水线面系数water plane coefficient (Cw)1.9描述船舶动态及静态的词汇terms to describe the dynamic[dai’nAmik] conditions and static positions纵倾trim 艉翘trim by stern 艏翘trim by head无纵倾状态even keel (non-trimmed condition)横倾heel or list 船体运动ship motion横摇rolling纵摇pitching艏摇yawing垂荡heaving横荡swaying纵荡surging1.10描述船体构件受力及变形的词汇describe the movement of hull structural member弯曲bending 扭曲twisting 屈曲buckling振动vibration 剪切sheering 横摇rolling 强摇racking1.11其他基本词汇(1)1)左舷port side 2) 右舷starboard side3) 纵向longitudinal 4) 横向transverse5) 水平horizontal 6) 垂直vertical 7) 中心线centre line (CL & )8) 舯midship or amidships (expressed by symbol )9) 船中区域midship part (0.4L ~ 0.5L)10) 船首bow 11) 艏柱stem 12) 艏部bow part or fore part13) 艏垂线fore perpendicular (FP)14) 艉柱stern 15) 艉部stern part or aft part16) 艉垂线aft perpendicular (AP)17) 尾端ends: these normally signify the end parts ofthe hull of a ship with 0.1L通常是指自船尾端始的0.1L的范围18) 基线base line (BL): normally the keel line 通常是指龙骨线19) 肋骨间距frame space 20) 肋骨线frame line21) 船体围长girth length: the length measured at the transverse section of the hull of a ship from gunnel to gunnel 在船体横截面上从一侧的船舷上沿量取到另一侧的船舷上沿的距离22) 龙骨上面top of keel 23) 折角线knuckle line (KL) 24) 折角点knuckle point25) 舷弧sheer 26) 艏舷弧fore sheer 27) 艉舷弧aft sheer 28) 梁拱camber29)甲板内倾tumble home 30) 外飘flare31)舭部升高rise of floor 32)平行部parallel part1.12其他基本词汇(2)1) 船桥甲板上缘top of bridge deck beam 2) 船桥楼外缘outline of bridge enclosure3) 上甲板梁上缘top of upper deck beam 4)梁拱camber5) 主甲板的内倾tumble home at upper deck6) 船桥甲板的内倾tumble home at bridge deck7) 上甲板边upper deck at side 8) 船中心线centre line of ship9) 舭部bilge part 10) 平板龙骨的一半half-side dimension of flat portion at keel11) 船中船桥甲板的型深moulded depth to bridge deck12) 船中主甲板处的型深moulded depth to upper deck13) 船中型吃水moulded draught1.13 线型lines1) 横剖线图body plan 2) 纵剖线图profile or sheer plan 3)半宽图水线half-breadth plan1.14其他图纸文件other plans and documents1) 除线型图之外,下列图纸被称为关键图(key plans):总体布置图general arrangement 中横剖面图midship section钢材构造图construction profile 外板展开图shell expansion2) 其他关键图以外的船体图纸被称为船厂图(yard plan):(1) 船体方面艏柱、艉柱、螺旋桨柱和舵结构stem, stern frame, propeller post and rudder甲板结构图deck plans 单底、双底结构图single bottom and double bottom水密和油密舱壁结构图watertight and oil tight bulkheads上层建筑端壁图superstructure end bulkhead船首、船尾、船底部抗拍击结构图arrangement to resist panting in both peaks and their vicinity [vi’siniti] 邻近, 接近支柱和甲板纵桁图pillars and deck girders 轴隧图shaft tunnels锅炉、主机、推力轴承、中间轴承、发电机和其它重要辅机基座图Seating of boiler, engine, thrust and plummer blocks dynamos 发电机机舱棚图machinery casings长甲板室结构图long deckhouse桅杆、桅室和绞车平台结构图masts and mast houses and winch platforms泵布置图pumping arrangements甲板装原木时绑扎装置布置图timber deck cargo security arrangements防火构造图construction for fire protection消防布置图plans showing fire extinguishing arrangement逃生路径布置图plans showing escape routes舱室路径图plans showing arrangement for access of tank and space(2) 轮机方面机器处所布置图machinery arrangement of machinery space船内通讯系统图diagram for internal communication system主、辅机图main and auxiliary engines动力传动齿轮、轴系及螺旋桨图power transmission gears, shafting and propellers锅炉及压力容器图boiler and pressure vessel辅机和管系图auxiliary machinery and piping操舵装置图steering gear自动控制及遥控装置图automatic and remote controls备件spare part 电气装置electrical installations 船桥视界navigation bridge visibility(3) 其他图纸文件船体轮机设计说明书specifications for hull and machinery船中横剖面模数计算书calculation sheets for minimum athwartship (横越) section modulus (模数) in way of the midship part防腐式样书corrosion prevention scheme 稳性计算书stability calculation sheets破舱稳性计算书damage stability calculation sheets装载手册loading manual 绑扎手册security manual1.15 静水力曲线hydrostatic curves浮心距基线高度centre of buoyancy above base line (KB)浮心距船中centre of buoyancy from midship (B)漂心距船中centre of floatation from midship (F)每厘米吃水吨数tons per one centimeter immersion (TPC)每厘米纵倾力矩moment to change one centimeter (CTM)水线系数water plane coefficient (Cw)纵稳心距基线高longitudinal metacentre above base line (LKM)横稳心距基线高transverse metacentre above base line (KM)棱形系数prismatic [priz’mAtik] coefficient (Cp)垂直棱形系数vertical prismatic coefficient (Cvp)方形系数block coefficient (Cb)型排水量displacement in tons excluding appendages (附件,附属物)总排水量displacement in tons including appendages船体湿表面面积wetted surface area (W.S.)1.16 稳性stability1)静态稳性intact stability 2)动态稳性dynamic stability3)稳性判据stability criteria (标准)4)稳性曲线stability curves5)倾斜试验inclining test 6)重心高度KG (height of centre of gravity)7)稳心高度KM (height of metacentre)8)初稳性高度GM 9)静稳性力臂GZ10)自由液面的影响free water effect11)大倾角稳性stability at a large inclination angle12)稳性十字曲线cross curves of stability13)纵向稳性longitudinal stability 14)横向稳性transverse stability15)破舱稳性damage stability 16)浸水计算flooding calculation17)浸水概率flooding probability 18)分舱compartment19)生存条件survival requirement 20)最终状态final stage21)生存概率survival probability 22)分舱指数subdivision index23)处所渗透率permeability of a space24)许用GM0曲线permissible GM0 curve1.17 波浪wave斯托克波stokes wave 正弦波sine wave 摆动波trochoidal wave船行波wave generated by ship sailing 散波divergent wave船尾横波stern transverse eave 船首横波bow transverse wave1.18 船体强度strength of ship船体垂向弯曲最终强度vertical bending ultimate strength船体梁强度hull girder strength 纵向强度longitudinal strength纵向弯距longitudinal bending moment 剪切力sheering force中拱hogging 中垂sagging静水弯距longitudinal bending moment in still water (Ms)波浪弯矩Mw(+) and Mw (-) wave induced longitudinal bending moment横向强度transverse strength 扭转强度twisting strength局部强度local strength 失稳强度buckling strength受压失稳强度compressive buckling strength剪切失稳强度sheer buckling strength直接强度计算/分析direct strength calculation / analyzing疲劳强度fatigue strength疲劳强度解析、评价fatigue strength anlyze, assessment应力集中stress concentration波浪周期wave period 随浪following wave 顶浪heading sea 横浪beam wave 波浪载荷wave load 垂向波浪弯距vertical wave bending moment波浪变动压hydrodynamic (水力,流体动力学)pressure舱室内压internal pressure 许用应力allowable stress最小弯距Wmin 剖面模数section modulus惯性矩moment of inertia强度连续性continuity of strength 板架、板单元plate panel1.19 船体尺寸限制Panama 圣。
船舶名词有哪些
我们通常在说船模型的船体部位时一般情况下都是用的大白话,比较简单易懂,所以当我们听到一些专业用语时,就会出现“这是什么?是什么意思呢?”类似这种反应,简单来说就是蒙圈了,那么为了避免这种尴尬,今天我就来给大家普及普及船舶名词有哪些。
船模型各部位及舱室名称:船首:船的前端部位。
他的两侧船壳弯曲处叫首舷;船尾:船的后端部位。
他的两侧船壳弯曲处叫尾舷;
壳组成部分。
相对应的是右舷;舱口:供入舱室或储存室的船舱开口,特指船舶甲板之间的通道口;货舱:指船上摆放货物的地方;船尾楼:安装系泊用绞缆机的船尾部分地方等,船模型各部位的名称当然远不止这些,这只是我们一般常见的,剩下的就靠我们慢慢挖掘吧!
船模型的相关术语:驾驶台:船舶航行指挥操作的地方;舵轮:维持船舶航向的方向盘;电罗经:根据陀螺原理、依靠电源维持高速稳定旋转制造的“指南针”;磁罗经:根据地磁引力制造的“指南针”,和电罗经配合使用;抛锚:指船抵港时,要抛锚固定船舶,和汽车抛锚完全是两个概念。
以上信息来源于同同模型,希望大家喜欢,谢谢阅读!。
船舶专业术语的名词解释在船舶领域中,有许多专业术语需要我们掌握和理解。
这些术语不仅有助于我们更好地了解船舶的结构和操作,还可以提升我们对航海学的整体理解。
在本文中,我们将解释一些常见的船舶专业术语,帮助读者更好地掌握这些知识。
1. 船舶:船舶是指由船体、船底、甲板和其他构件组成的水上交通工具。
船舶通常被用于运送人员、货物或完成其他特定任务,如捕鱼和水上搜救。
2. 船体:船体是船舶的主体结构,它包括船的外壳以及负责支撑和保护船舶的骨架结构。
船体通常由钢铁、铝合金或纤维复合材料等材料制造。
3. 船底:船底是船舶底部的部分,它负责支撑整个船体并与水面接触。
船底的形状和设计对航海的稳定性和操控性起着重要作用。
4. 船首:船首是船舶的前部,也被称为船头。
船首通常设计成较为尖锐的形状,以减少阻力并提高船舶的速度。
5. 船尾:船尾是船舶的后部,也被称为船尾。
船尾通常设计成较为平坦的形状,以确保船舶在航行时保持稳定。
6. 舵:舵是控制船舶方向的装置,通常由舵柄和舵叶组成。
舵位于船尾附近,通过调整舵叶的角度来改变船舶的方向。
7. 螺旋桨:螺旋桨是船舶主要的推进装置,它通过旋转产生推力,推动船舶前进。
螺旋桨通常由多个叶片组成,可以根据需要调整叶片的角度。
8. 航行灯:航行灯是安装在船舶上的特定灯光,用于指示船舶的位置和方向。
根据国际海事组织的规定,航行灯的颜色和位置有具体的要求。
9. 舱室:舱室是船舶内部用于储藏货物、设备和乘客的空间。
舱室通常被划分成不同的区域,以方便管理和使用。
10. 舱盖:舱盖是船舶上覆盖货物储存区域或机舱的结构。
舱盖可以防止海水进入船舶并保护货物免受恶劣天气的影响。
11. 锚:锚是用于固定船舶位置的重型金属设备。
锚通过抛掷到水底并拉紧锚链来确保船舶在停泊时保持在所需的位置上。
12. 喷气推进器:喷气推进器是一种通过喷射水流产生推力的推进装置。
它适用于需要快速起降或需要在浅水区域进行操作的船舶。
船舶英文名词船舶结构部件名称以及相关名词2014-05-13 中国海员之家1.1船长1)总长Loa:length of overall2)垂线间长Lbp:length between perpendiculars3)登记船长L:registered length4)干舷长Lf:freeboard length5)船舶分舱长度LS:subdivision length6)艉垂线:aft perpendicular7)艏垂线:forward perpendicular8)后端点:aft end point9)挪威规范,英国规范:Oslo Rules, UK Rules10)前端点:fore end point11)美国规范:USA Rules12)艏楼甲板:F’cle Dk13)日本规范: Japanese Rules14)艏柱:stem15)水线长:length of water line16)干舷长前端点: forward end of freeboard length1.2 船宽1)登记船宽B:registered breadth2)上甲板Upp Deck3)角隅圆弧的断点:termination of corner radius4)干舷船宽Bf : breadth of ship for freeboard5)分舱船宽Bs : subdivision breadth of ship1.3 型深(D)depth1.4 吃水d: draught or draft1.5 干舷: freeboard1.6 吨位及舱容tonnage and cargo capacity总吨gross tonnage 净吨net tonnage苏伊士运河吨位Suez Canal tonnage巴拿马运河吨位Panama Canal tonnage排水量displacement载重吨deadweight国家吨位national tonnage国际吨位international tonnage包装货物舱容bale capacity谷物舱容grain capacity外板shell plating 护肋材sparring谷物容积限度grain capacity捆包容积限度limit of bale capacityg表示谷物容积g indicates grain capacity b表示捆包容积b indicates bale capacity底部垫木bottom ceiling1.7船速speed1.8 船型系数block coefficient细长型fine form 肥大型full form 方形系数block coefficient (Cb)中横剖面系数midship coefficient (Cm)棱形系数prismatic coefficient (Cp)水线面系数water plane coefficient (Cw)1.9描述船舶动态及静态的词汇terms to describe the dynamic[dai’nAmik] conditions and static positions纵倾trim 艉翘trim by stern 艏翘trim by head无纵倾状态even keel (non-trimmed condition)横倾heel or list 船体运动ship motion横摇rolling纵摇pitching艏摇yawing垂荡heaving横荡swaying纵荡surging1.10描述船体构件受力及变形的词汇describe the movement of hull structural member弯曲bending 扭曲twisting 屈曲buckling振动vibration 剪切sheering 横摇rolling 强摇racking1.11其他基本词汇(1)1)左舷port side 2) 右舷starboard side3) 纵向longitudinal 4) 横向transverse5) 水平horizontal 6) 垂直vertical 7) 中心线centre line (CL & )8) 舯midship or amidships (expressed by symbol )9) 船中区域midship part (0.4L ~ 0.5L)10) 船首bow 11) 艏柱stem 12) 艏部bow part or fore part13) 艏垂线fore perpendicular (FP)14) 艉柱stern 15) 艉部stern part or aft part16) 艉垂线aft perpendicular (AP)17) 尾端ends: these normally signify the end parts ofthe hull of a ship with 0.1L通常是指自船尾端始的0.1L的范围18) 基线base line (BL): normally the keel line 通常是指龙骨线19) 肋骨间距frame space 20) 肋骨线frame line21) 船体围长girth length: the length measured at the transverse section of the hull of a ship from gunnel to gunnel 在船体横截面上从一侧的船舷上沿量取到另一侧的船舷上沿的距离22) 龙骨上面top of keel 23) 折角线knuckle line (KL) 24) 折角点knuckle point25) 舷弧sheer 26) 艏舷弧fore sheer 27) 艉舷弧aft sheer 28) 梁拱camber29)甲板内倾tumble home 30) 外飘flare31)舭部升高rise of floor 32)平行部parallel part1.12其他基本词汇(2)1) 船桥甲板上缘top of bridge deck beam 2) 船桥楼外缘outline of bridge enclosure3) 上甲板梁上缘top of upper deck beam 4)梁拱camber5) 主甲板的内倾tumble home at upper deck6) 船桥甲板的内倾tumble home at bridge deck7) 上甲板边upper deck at side 8) 船中心线centre line of ship9) 舭部bilge part 10) 平板龙骨的一半half-side dimension of flat portion at keel11) 船中船桥甲板的型深moulded depth to bridge deck12) 船中主甲板处的型深moulded depth to upper deck13) 船中型吃水moulded draught1.13 线型lines1) 横剖线图body plan 2) 纵剖线图profile or sheer plan 3)半宽图水线half-breadth plan1.14其他图纸文件other plans and documents1) 除线型图之外,下列图纸被称为关键图(key plans):总体布置图general arrangement 中横剖面图midship section钢材构造图construction profile 外板展开图shell expansion2) 其他关键图以外的船体图纸被称为船厂图(yard plan):(1) 船体方面艏柱、艉柱、螺旋桨柱和舵结构stem, stern frame, propeller post and rudder甲板结构图deck plans 单底、双底结构图single bottom and double bottom水密和油密舱壁结构图watertight and oil tight bulkheads上层建筑端壁图superstructure end bulkhead船首、船尾、船底部抗拍击结构图arrangement to resist panting in both peaks and their vicinity [vi’siniti] 邻近, 接近支柱和甲板纵桁图pillars and deck girders 轴隧图shaft tunnels锅炉、主机、推力轴承、中间轴承、发电机和其它重要辅机基座图Seating of boiler, engine, thrust and plummer blocks dynamos 发电机机舱棚图machinery casings长甲板室结构图long deckhouse桅杆、桅室和绞车平台结构图masts and mast houses and winch platforms泵布置图pumping arrangements甲板装原木时绑扎装置布置图timber deck cargo security arrangements防火构造图construction for fire protection消防布置图plans showing fire extinguishing arrangement逃生路径布置图plans showing escape routes舱室路径图plans showing arrangement for access of tank and space(2) 轮机方面机器处所布置图machinery arrangement of machinery space船内通讯系统图diagram for internal communication system主、辅机图main and auxiliary engines动力传动齿轮、轴系及螺旋桨图power transmission gears, shafting and propellers锅炉及压力容器图boiler and pressure vessel辅机和管系图auxiliary machinery and piping操舵装置图steering gear自动控制及遥控装置图automatic and remote controls备件spare part 电气装置electrical installations 船桥视界navigation bridge visibility(3) 其他图纸文件船体轮机设计说明书specifications for hull and machinery船中横剖面模数计算书calculation sheets for minimum athwartship (横越) section modulus (模数) in way of the midship part防腐式样书corrosion prevention scheme 稳性计算书stability calculation sheets破舱稳性计算书damage stability calculation sheets装载手册loading manual 绑扎手册security manual1.15 静水力曲线hydrostatic curves浮心距基线高度centre of buoyancy above base line (KB)浮心距船中centre of buoyancy from midship (B)漂心距船中centre of floatation from midship (F)每厘米吃水吨数tons per one centimeter immersion (TPC)每厘米纵倾力矩moment to change one centimeter (CTM)水线系数water plane coefficient (Cw)纵稳心距基线高longitudinal metacentre above base line (LKM)横稳心距基线高transverse metacentre above base line (KM)棱形系数prismatic [priz’mAtik] coefficient (Cp)垂直棱形系数vertical prismatic coefficient (Cvp)方形系数block coefficient (Cb)型排水量displacement in tons excluding appendages (附件,附属物)总排水量displacement in tons including appendages船体湿表面面积wetted surface area (W.S.)1.16 稳性stability1)静态稳性intact stability 2)动态稳性dynamic stability3)稳性判据stability criteria (标准)4)稳性曲线stability curves5)倾斜试验inclining test 6)重心高度KG (height of centre of gravity)7)稳心高度KM (height of metacentre)8)初稳性高度GM 9)静稳性力臂GZ10)自由液面的影响free water effect11)大倾角稳性stability at a large inclination angle12)稳性十字曲线cross curves of stability13)纵向稳性longitudinal stability 14)横向稳性transverse stability15)破舱稳性damage stability 16)浸水计算flooding calculation17)浸水概率flooding probability 18)分舱compartment19)生存条件survival requirement 20)最终状态final stage21)生存概率survival probability 22)分舱指数subdivision index23)处所渗透率permeability of a space24)许用GM0曲线permissible GM0 curve1.17 波浪wave斯托克波stokes wave 正弦波sine wave 摆动波trochoidal wave船行波wave generated by ship sailing 散波divergent wave船尾横波stern transverse eave 船首横波bow transverse wave1.18 船体强度strength of ship船体垂向弯曲最终强度vertical bending ultimate strength船体梁强度hull girder strength 纵向强度longitudinal strength纵向弯距longitudinal bending moment 剪切力sheering force中拱hogging 中垂sagging静水弯距longitudinal bending moment in still water (Ms)波浪弯矩Mw(+) and Mw (-) wave induced longitudinal bending moment横向强度transverse strength 扭转强度twisting strength局部强度local strength 失稳强度buckling strength受压失稳强度compressive buckling strength剪切失稳强度sheer buckling strength直接强度计算/分析direct strength calculation / analyzing疲劳强度fatigue strength疲劳强度解析、评价fatigue strength anlyze, assessment应力集中stress concentration波浪周期wave period 随浪following wave 顶浪heading sea 横浪beam wave 波浪载荷wave load 垂向波浪弯距vertical wave bending moment波浪变动压hydrodynamic (水力,流体动力学)pressure舱室内压internal pressure 许用应力allowable stress最小弯距Wmin 剖面模数section modulus惯性矩moment of inertia强度连续性continuity of strength 板架、板单元plate panel1.19 船体尺寸限制Panama 圣。
船舶名词解释
船舶名词解释
1. 船体:指船舶的本体,是支承由外壳、激流板、船底及其他装置组成的结构。
2. 外壳:指船舶的主体本体,它的外部形状决定了船舶的吃水、空气抵抗力和抗侧摇能力。
3. 激流板:指船舶船身上的横向结构,它能够改变船体水动力特性,改善船舶结构性能。
4. 船底:指船舶的顶部,它决定船舶的底部受力和抗侧摇性能,以及船舶的抗滚能力、航行舒适度和燃油效率。
5. 船网:指船舶的外壳和底衬,它们的结构和材料决定了船舶的结构强度、重量和耐久性。
6. 船只引擎:指船舶运动的推力装置,可以用于改善船舶的航行性能,如提高稳定性、加快航行速度等。
7. 船墙:指船舶的外壳结构,用于抵御海洋巨浪、寒冷和风雨等自然环境因素的侵袭。
8. 船首:指船舶前部的结构,用来抵御前进过程中的波浪的冲击和翻腾,以保护船舶的船体安全。
9. 船尾:指船舶后部的结构,用来减弱船舶的动能,以及对海浪作出反应,以降低船舶在航行过程中的摇摆和翻腾。
10. 驾驶室:指船舶的指挥控制中心,它的设备可以控制船舶的航行,包括导航、航行、舵操纵等系统。
市舶贸易名词解释
市舶贸易名词解释
一、船舶名词
1. 货船:也称货轮或商船,主要用于运输各种货物的一种船只。
2. 油轮或油船:指用于运输石油或其它燃料的船只。
3. 拖船:指以牵引普通船舶或其它拖船为主要作业的船只。
4. 客船:指以客运为主要作业的船只。
5. 装卸船:指用于装卸(装运、卸货)船舶、货物的船只。
6. 拖轮:指以拖拉拖轮、拖轮及其组合体为主要作业的船只。
7. 救助船:指为提供海上抢救、拯救、救济或护航服务的船只。
8. 护卫船:指为护卫其他船只、保护海上航行安全的船只。
二、贸易名词
1. 海运:指船舶运输货物及其服务的一种运输方式。
2. 国际贸易:指不同国家之间在国际竞争环境下进行货物及服务的贸易。
3. 进口贸易:指从外国进口商品或服务的贸易。
4. 出口贸易:指向外国出口商品或服务的贸易。
5. 贸易金融:指在国际贸易中所使用的金融服务,如支付、履约保证、抵押等。
6. 交易所:指市场上进行国际贸易活动的机构,如纽约商品交易所、伦敦金融交易所等。
7. 国际仲裁:指利用国际仲裁原则来解决国际贸易争端的方式。
8. 国际贸易法:指由国际间贸易条约、国际间国际协议等等组成的一套法律,用以规范并解决国际贸易之间争端。
1 sea keeping performance 耐波性能2 maneuverability 操纵性3 endurance 续航力,全功率工作时间4 cargo handling 货物装载5 subdivision 分舱6 stability 稳性7 freeboard 干舷8 tonnage 吨位9 basic design 基本设计10 concept design 概念设计11 preliminary design 初步设计12 contract design 合同设计13 design spiral 设计螺旋循环方式14 bidder 投标人15 iterative process 迭代过程16 naval architecture 造船学17 feasibility study 可行性研究18 beam 船宽,梁19 depth 船深20 draft 吃水21 fullness 丰满度22 cargo cubic 货舱舱容,载货容积23 deadweight 总载重量(吨)24 talking paper 讨论文件25 light-ship 空船26 a faired set of lines 经过光顺处理的一套型线27 hull form 船形,船体外形28 frame 船肋骨,框架,桁架29 fresh water 淡水30 living and utility spaces 居住与公用舱室31 outfit 舾装32 trial 实船试验33 major ship 大型船舶34 detail design 详细设计35 ship fitter 船舶装配工36 welder 焊工37 metal worker 金属工38 machinery vendor 机械(主机)卖方39 outfitter 舾装工40 pipe fitter 管装工41 artisan 技工42 shipyard 船厂43 break bulk 件杂货44 containerized 集装箱化45 liner trade 定期班轮营运业46 tanker 油船47 bulk carrier 散装货船48 offshore drilling 离岸钻井49 drilling rig 钻架50 pipe laying barge (海底)铺管驳船51 fleets of vessels 船队52 outboard profile 侧视图53 inboard profile 纵剖面图54 general arrangement 总布置图55 hold 船舱56 crew quarters 船员居住舱57 commissary spaces 补给库舱室,粮食库58 lines 型线59 plan views 设计图60 midship section 舯横剖面61 elevations 高度,高程,船型线图的侧面图,立视图,纵剖线图,海拔62 sections 剖面,横剖面63 main shafting 主轴系64 power and lighting system 动力与照明系统65 diagram 图,原理图,设计图,流程图66 ventilation and air conditioningdiagram 通风与空调敷设设计图67 normal operating condition 常规(正常)运作状况68 capacity plan 舱容图69 curves of form 各船型曲线70 floodable length curve 可浸长度曲线71 trim 纵倾72 damage stability 破损稳性73 naval architect 造船师74 naval architecture 造船工程75 categorize 分类76 aerostatic 空气静力学的77 self-induced 自身诱导的78 cushion of air 气垫79 lift fan 升力风扇80 skirt (气垫船)围裙81 air cushion vehicle 气垫船82 amphibious 两栖的83 rigid side walls 刚性侧壁84 captured-air-bubble vehicle 束缚气泡减阻船85 supper cavitating propeller 超空泡螺旋桨86 ferry 渡轮,渡口,渡运航线87 cross-channel automobileferries 横越海峡车客渡轮88 polar-exploration craft 极地考察船89 landing craft 登陆艇90 riverine warfare vessel 内河舰艇91 hydrodynamic 水动力学的92 flow pattern 流型,流线谱93 airfoil 气翼,翼剖面,机面,方向舵94 hydrofoil 水翼95 surface piercing 穿透水面的96 strut 支柱,支撑构性97 planing hull 滑行船体98 V-section V型剖面99 deep V hull 深V型船体100 rough sea 汹涌的海浪101 buoyant 浮力的102 displacement 排水量103 common carrier 通用运输船104 trawling 拖网105 crussing range 航程106 seaworthness 适航性107 bulk oil carrier 散装油轮108 tanker 油轮109 supertanker 超级油轮110 LCC(Large Crude Carrier)大型原油轮(载重10~20万吨)111 VLCC(Very Large Crude Carrier)巨型(原)油轮(载重量>20万吨)112 ULCC(Ultra Large Crude Carrier)超级大型(原)油轮(载重量>40万吨)113 SWATH(Small Waterplane Area Twin Hull)小水线面双体船114 multihull vessel 多体船115 catamaran 双体船116 trimaran 三体船117 launch 发射,下水118 launching equipment (向水中)投放设备119 configuration 安排,构型,配置120 submersible 潜器121 endurance 续航力122 payload 有效载荷123 merchant ship 商船124 survivability 生存力125 babitability 适居性126 commercial ship 营利用船127 freight rate 运费率128 life-cycle cost 生命周期成本129 acquisition cost 购置(获取)成本130 pleasure ship 游乐用船131 naval ship 军船132 liner 定期航班船133 tugboat 拖船134 hostile sea 凶险的波浪135 oil-rig 钻井架136 roll-on/ro-off(Ro-Ro)滚装137 aircraft carrier 航空母舰138 guided-missile cruiser 导弹巡洋舰139 destroyer 驱逐舰140 at-sea replenishment 海上补给141 reenlistment 重征服役142 icebreaker 破冰船143 Coast Guard cutte (美国)海岸警备队快艇144 principal dimensions 主尺度145 perpendicular (船艏、艉)柱,垂直的,正交的146 forward/after perpendicular 艏/艉柱147 length between Perpendicular 两柱间长148 stem 船艏149 summer load water line 夏季载重水线150 rudder post 舵柱151 pintle 销,枢轴152 dock 泊靠153 length overall 总长154 overhang 外悬155 stern 艉156 rake 倾斜157 bulbous bow 球鼻艏158 trim 纵倾159 amidships 舯160 breadth moulded 型宽161 breadth extreme 最大宽,计算宽度162 shell planting 船壳板163 fender 护舷164 quay (横)码头,停泊所165 depth 船深166 rounded gunwale (修圆的舷边)167 sheer (甲板)舷弧168 sheer forward 艏舷弧169 sheer aft 艉舷弧170 deck line at side 甲板边线171 camber 梁拱172 drainage 排(泄)水173 rise of floor 底升174 bilge 舭,舱底175 flat of keel 平板龙骨176 rivet 铆接,铆钉177 girder 桁梁,桁架178 bevel 折角179 bar 型材,材180 tumble home (船侧)内倾181 seakeeping 适航性182 base line 基线183 trim by the stern/bow 艏/艉倾184 bar keel 棒龙骨,方龙骨,矩形龙骨185 draught(=draft)吃水,草图,设计图,牵引力186 imperial unit 英制单位187 metric unit 公制单位188 hog 中拱189 sag 中垂190 dry dock 干船坞191 freeboard 干舷192 weather deck 露天甲板193 seaworthness 适航性194 Load Line Regulations 载重线公约、规范195 sheer profile 纵剖线196 accommodation 居住(舱室)197 bilge radius 舭半径198 reserve buoyancy 储备浮力199 heel 横倾200 Superstructure 上层建筑201 deckhouse 舱面室,甲板室202 surmount 顶上覆盖,越过203 middle line plane 中线面204 sheer plane 水线面205 keel 龙骨206 transverse section 横剖面207 orthogonal 正交的,矩形的208 body plan 横剖面图209 by convention 按照惯例,按约定210 half breadth plan 半宽图211 lines plan 型线图212 sheer drawing 剖面图213 load waterplane 载重水线面214 slice 一部分,薄片215 intersection 交点,交叉,横断(切)216 fore/aft perpendicular 艏/艉柱217 vicinity 邻近,附近218 length between perpendiculars 垂线间长219 maximum beam amidships 舯最大宽220 tumble home 内倾221 flare 外飘,外张222 rake 倾斜,倾斜度,倾斜角223 conspicuous 显著的,值得注意的224 funnel 烟囱225 deck camber 甲板梁拱226 concave 凹,凹的,拱形的227 mast 桅杆228 stem contour 艏柱型线229 heel 横倾230 yaw 艏摇231 drift 漂移,偏航232 Bonjean curve 邦戎曲线233 conceive 设想,想象234 impression 模槽,型腔,印痕,印象235 appendage 附体236 abaft 朝向船尾237 rudder 舵238 bilge 舭239 circumscribe 外接,外切240 rectangle 矩形241 yacht 快艇242 midship section coefficient 舯横剖面系数243 block coefficient 方形系数244 longitudinal prismatic coefficient 纵向菱形系数245 vertical prismatic coefficient 垂向菱形系数246 cross-sectional area 横剖面面积247 Lloyd’s Rules 劳埃德(船级社)规范248 adopt 采用249 principal dimensions 主尺度250 length overall 总长251 port 左舷252 starboard 右舷253 freeboard 干舷254 beam 船身最大宽,横梁255 girder 桁,梁256 chine 舭,舷,脊257 soft chine 圆舭258 hard chine 尖舭259 transom(stern)方尾260 cruiser stern 巡洋舰尾261 ship form 船型262 lines plan 型线图263 orthogonal 正交的264 body section 横剖图265 division 站,划分,分隔266 base, base line 基线267 water line 水线268 sheer profile 纵剖图269 buttock 后体纵剖线270 bow line 前体纵剖线271 fair 光顺272 offsets 型值273 lift offsets 量取型值274 (to)run the waterlines 绘制水线275 batten 压条276 drawing office 绘图室277 scale 缩尺,尺度,尺278 mould loft 放样间279 shipyard 船厂280 full scale 全尺度281 loft floor 放样台282 contracted scale 缩尺283 mark out 划线,划记号284 pin 钉,销285 moulded line 型线286 in strake 内列板287 out strake 外列板288 in way of…在……处289 wing shaft 侧轴290 shaft bossing 轴包套291 stiffen 加劲,加强292 frame 框架,肋骨293 shaft bracket 轴支架294 appendage 附件,附体295 cross section 横剖面296 amidships 在舯部,舯297 parallel middle body 平行中体298 fine fast ship 纤细(细长)高速船299 abaft 朝船尾300 entrance 进流段301 run 去流段302 forward/after shoulder 前/后肩303 buoyancy 浮力304 load waterline 载重水险305 from coefficient 船形系数306 block coefficient 方形系数307 bulk carrier 散装货船308 prismatic coefficient 菱形系数309 immerse 浸入,浸没310 circumsection 外切311 midship area coefficient 舯横剖面系数312 waterplane area coefficient 水线面积系数313 prism 棱柱体314 vertical prismatic coefficient 垂向菱形系数315 U-form U型316 V-shaped V形的317 full form 丰满船型318 fine form 瘦长(细长)船型319 classification society 船级社320 governmental authorities 政府当局,管理机构321 ship owner 船东322 underwriter 货主323 risk (海运)保险商324 Lloyd’s Register of shipping (英国)劳埃德船级社325 Department of Trade (英国)贸易部326 Board of Trade (英国)贸易厅327 standard 规章328 supervision of the society’s surveyor 船级社验船师的监造书329 Lloyd’s machinery certificate (LMC)劳埃德(船舶)机械证书330 register (船舶)登录簿,船名录331 fire protection, detection and extinction 防火,探火与灭火332 liquefied gas carrier 液化气运输船333 Green Book (船级社)绿皮书,(19世纪英国另一船级社的船名录,现合并于劳埃德船级社,用于登陆快速远洋船)334 ton gross= gross ton 长吨=1.016公吨335 dredge 挖泥船336 hopper barge (自动)倾卸板337 scantling 材积338 casualty 事故,死伤,灾难339 corrosion 锈蚀,腐蚀340 Bureau Veritas (法国)船级社341 American Bureau Shipping (美国)船级社342 Germanischer Lloyd (德国)劳埃德船级社343 Registo Italiano Navade (意大利)船级社344 International Association of Classification Society (IACS)国际船级社联合会345 to vet proposals 审查新建议346 legislation 立法347 Merchant Shipping Acts 商业运输法348 life saving appliance 救生设备349 carriage of grain cargoes 谷类货物运输机350 introduces a bill 提出一项议案351 Plimsoll line 普林索尔载重线352 reserve buoyancy 储备浮力353 freeboard deck 干舷甲板354 athwart ships (船)横向355 Type A ship A类船356 gasketed openings 装以密封垫的开口357 compartment 舱室358 tabular freeboard 列成表格的干舷船359 Suez Canal tonnage 苏伊士运河吨位限制360 Panama Canal 巴拿马运河361 Stringent safety regulations 严格的安全规章362 maritime 海事的,海运的,靠海的,延海的363 titanic 巨大的364 the Titanic 泰坦尼克号365 maiden voyage 处女航366 flood 进水,泛滥367 Inter-national Convention for the Safety of Life at Sea(ICSOLAS)海上生命安全性国际公约368 permanent body 永久性组织机构369 aegis 保护,庇护370 Inter-governmental Maritime Consultive Organization(IMCO)国际政府间海事质询组织371 The Register of Shipping of the People’s Republic of China中国船舶检验局372 static equilibrium 静平衡373 neutral equilibrium 中性平衡374 upright position 正浮位置375 homogeneous cylinder 均质柱状体376 capsize 倾覆377 resultant 合力378 couple 力矩,力偶379 positive righting moment 正扶正力矩380 righting arm 扶正力臂,恢复力臂381 capsizing moment 倾覆力矩382 met center 稳心383 list 倾斜,倾侧384 stable equilibrium 稳定平衡385 criterion 判据,准则386 overall stability 总体稳性387 initial stability at small angle of inclination 小倾角初稳性388 met centric height 稳心高389 off-center loading 偏离中心的装载390 port 左舷391 starboard 右舷392 lighter 港驳船393 watertight integrity 水密完整性394 crucial element 重要因素395 intact stability 完整稳性396 barge 驳船397 ship hydrodynamics 船舶水动力学398 transverse stability 横稳性399 appendage 附体400 frictional resistance 摩擦阻力401 eddy 旋涡402 gradient 梯度403 wetted surface 湿表面积404 Reynolds number 雷诺数405 wave-making resistance 兴波阻力406 eddy-making resistance 旋涡阻力407 extrapolate 外插408 residuary resistance 剩余阻力409 speed-to-length ratio 速长比410 nautical mile 海里411 bow wave 艏波412 wave pattern 波型413 stern wave 艉波414 fair 光顺415 hole 水(流)深凹处416 mid-body (船)中体417 shoulder 船肩418 crest(of wave)波峰419 trough 波谷420 bulb 球鼻首421 bracket 轴支架,支架422 buoyancy 浮力423 viscosity 粘性424 streamline 流线425 curvature 曲率426 paddle 桨427 oar 橹;桨428 paddle-wheel-propelled 明轮推进的429 Admiralty 海军部,海军上将430 barge 驳船431 double-acting steam cylinder 双向作用的一、船舶种类1、一般ship, vessel 船舶,船warship 舰boat, craft 艇raft, float 筏naval ship 军用船civil ship, merchant ship 民用船2、战斗舰艇combatant ship 战斗舰艇,军舰surface combatant ship 水面战斗舰艇aircraft carrier 航空母舰attack aircraft carrier 攻击航空母舰antisubmarine aircraft carrier 反潜航空母舰helicopter carrier 直升机母舰cruiser 巡洋舰guided missile cruiser 导弹巡洋舰destroyer 驱逐舰guided missile destroyer 导弹驱逐舰frigate 护卫舰guided missile frigate 导弹护卫舰antisubmarine frigate 反潜护卫舰minelayer 布雷舰guided missile boat 导弹艇torpedo boat 鱼雷艇submarine chaser 猎潜艇gun boat 炮艇landing ship 登陆舰dock landing ship 坞式登陆舰landing craft 登陆艇minesweeper 扫雷舰minesweeper, minesweeping boat 扫雷艇remote control minesweeper 遥控扫雷艇submarine 潜艇guided missile submarine 导弹潜艇ballistic missile submarine 弹道导弹潜艇cruising missile submarine 飞航导弹潜艇torpedo submarine 鱼雷潜艇nuclear-powered submarine 核潜艇conventionally-powered submarine 常规潜艇3、辅助舰船auxiliary ship 辅助舰船repair ship 修理舰training ship 训练舰tender, depot ship 供应舰replenishment ship 补给舰scout ship, reconnaissance ship 侦察船target vessel 靶船remote control target boat 遥控靶艇torpedo recovery vessel 捞雷船degaussing ship, demagnetizing ship 消磁船hospital ship 医院船research ship, test vessel 研究试验船instrumented tracking and telemetry ship 跟踪遥测船underwater acoustics research ship 水声试验船patrol boat 巡逻艇bridge boat, pontoon raft 浮桥舟4、运输船transport ship 运输船passenger ship 客船passenger cargo vessel 客货船cargo ship, freight vessel 货船dry cargo ship 干货船bulk cargo carrier 散货船bulk grain carrier 散粮船cement carrier 散装水泥船collier, coal carrier 运煤船ore carrier 矿砂船dual-purpose carrier, oil and bulk carrier, oil and ore carrier 两用散货船triple-purpose carrier, oil-bulk and ore carrier 三用散货船general cargo ship 杂货船liquid cargo ship 液货船oil tanker, tanker 油船liquid chemical tanker 液体化学品船liquefied(liquified)natural gas carrier 液化天然气船refrigerated ship, cold storage ship 冷藏船fruit carrier 运水果船meat carrier 运肉船container ship 集装箱船full container ship 全集装箱船semi-container ship 半集装箱船roll-on/roll-off ship, drive-on/drive-off ship 滚装船barge carrier, lighter aboard ship 载驳船automobile carrier 运汽车船timber carrier 运木船cattle carrier 牲畜船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船train ferry 列车渡船automobile ferry 汽车渡船barge, lighter 驳船passenger barge 客驳freight barge, cargo barge 货驳integrated barge 分节驳large opening barge 舱口驳open barge 敞舱驳covered barge, deck barge 甲板驳well-deck barge 半舱驳5、工程船working ship 工程船ocean development ship 海洋开发船self-elevating drilling platform 自升式钻井平台jack-up self-elevating drilling platform 桩腿自升式钻井平台shoe self-elevating drilling platform 桩靴自升式钻井平台mat self-elevating drilling platform 沉垫自升式钻井平台bottom supporting drilling platform 定柱沉垫式钻井平台floating drilling rig 浮式钻井装置semi-submersible drilling rig 半潜式钻井装置drilling ship 钻井船center-mooring drilling ship 中心锚泊钻井船drilling barge 钻井驳船swamp drilling barge 沼泽地钻井驳船drilling tender 钻井辅助船dredger 挖泥船suction dredger 扬吸挖泥船trailing suction hopper dredger 耙吸式挖泥船cutter suction dredger 绞吸式挖泥船dustpan suction dredger 冲吸式挖泥船jet lift dredger 喷射挖泥船bucket dredger 链斗挖泥船sand pump bucket dredger 自扬链斗挖泥船overhead bucket dredger 高架链斗挖泥船self-propelled bucket dredger 自航链斗挖泥船grab dredger 抓斗挖泥船self-propelled grab hopper dredger 自航抓斗挖泥船dipper dredger 铲斗挖泥船amphi dredger 两栖挖泥船mud lighter 泥驳elevater barge 封底泥驳hopper barge 开底泥驳side hopper barge 侧开泥驳split type dump hopper barge 对开泥驳floating crane, derrick boat 起重船slew type floating crane 转机式起重船fixed type floating crane 定机式起重船luff type floating crane 定机变幅式起重船floating pile driver piler 打桩船floating sand piler 砂桩打桩船floating pile presser 压桩船layer 布设船danlayer, buoy(age)vessel 布标船dan boat 航标工作船cable layer, cable ship 布缆船pipelaying barge, pipeline layer 铺管船bury barge 埋管船salvage and rescue ship 打捞救生船salvage and rescue ship 救捞船salvage barge 救捞驳船rescue tug 救助拖船rescue ship 救生船submarine rescue vessel 援潜救生船high speed life boat 救生快艇deep submergence rescue vehicle 深潜救生艇floating dock 浮船坞single unit floating dock 整体式浮船坞pontoon floating dock 浮箱式浮船坞three-piece type floating dock 三段式浮船坞integrated floating dock 组合式浮船坞surveying ship 测量船ice-breaker 破冰船sweeper 扫海船underwater drilling and blasting ship 炸礁船rock crusher 碎石船light boat 灯标船barge unloading suction dredger 吹泥船floating booster stating 接力泵船drilling ship 钻探船stone dumper 抛石船floating concrete mixer 混凝土搅拌船diving vessel, divers boat 潜水工作船generating ship 电站船repair ship 修理船distilling ship 海水淡化船dredger 采矿船gold dredger 采金船anchor boat 起锚船floating living quarter 住宿船self-elevating platforms for civil engineering 水上施工平台6、渔业船fisheries 渔业船fisheries guidance ship 渔业指导船fisheries administration ship 鱼政船fisheries inspection boat 渔业监督船fisheries rescue ship 渔业救助船fisheries rescue ship 渔船trawler 拖网渔船bull trawler 对拖网渔船single trawler 单拖网渔船stern ramp trawler 尾滑道拖网渔船seine netter 围网渔船gill netter 刺网渔船square netter 敷网渔船line fishing boat, liner 钓渔船pole and line fishing boat 竿钓渔船trolling boat, troller 拖钓渔船long liner 延绳钓渔船squid angling boat 鱿鱼钓渔船fishing sailer 风帆渔船fishing motor sailer 机帆渔船whaling ship 捕鲸船combination fishing vessel 多种作业渔船pearl boat 海珍品采集船fisheries auxiliary vessel 渔业辅助船fishery mother ship 渔业基地船fish factory ship 渔业加工船whale factory ship 捕鲸母船fisheries tender 渔业补给船buy boat 收鲜船refrigerated seawater fish carrier冷海水保险运输船live fish carrier 活鱼运输船fish luring light boat, lurker 诱鱼灯船二、船舶总布置1、一般ships general arrangement 船舶总布置interior arrangement 舱室布置arrangement of shipboard weapons 武备布置stairway and passageway arrangement 梯道布置engine room arrangement 机舱布置shafting arrangement 轴系布置compartment 舱space 舱室2、甲板、平台、通道bridge deck 驾驶甲板compass deck 罗经甲板boat deck 艇甲板promenade deck 游步甲板accommodation deck 起居甲板vehicle deck 车辆甲板flight deck 飞行甲板angled deck 斜角甲板helicopter deck 直升机甲板hangar deck 机库甲板tank deck 坦克甲板winch platform 起货甲板gun platform 火炮甲板passage passageway 通道interior passageway 内通道exterior passageway 外通道3、工作和设备舱室wheel house 驾驶室chart room 海图室coding room 译电室radio room 报务室spare radio room 备用报务室radar room 雷达室sonar control room 声纳室combat information center 情报中心fire director room, weapon control room 指挥仪室main engine room 主机舱main engine control room 主机操纵室auxiliary engine room 辅机舱reactor room 反应堆舱boiler room 锅炉舱engine and boiler room 机炉舱reduction gear room 减速器舱steering engine room 舵机舱fan room 通风机舱commutator room 变流机舱air-conditioning unit room 空调室emergency generator room 应急发电机室refrigerator room 冷冻机室fire-smothering unit room 灭火装置室battery room 蓄电池室gyro-compass room 陀螺罗经室log room 计程仪室missile magazine 导弹舱magazine 弹药舱depth charge magazine 深弹舱depth charge rack room 深弹滚架舱ammunition lobby 弹药运转间sonar transducer room 声纳舱workshop 机修间electrician’s store 电工间carpenter’s store 木工间chain locker 锚链舱mast house 桅室decontamination room 洗消室4、生活舱室living accommodation 生活舱室living accommodation 居住舱室captain’s room 船长室crew’s room 船员室cabin 客舱political commissar’s room 政委室political officer’s room 政委室group commander’s room 编队指挥员室captain’s room 舰长室vice captain’s room 副长室officer’s room 干部室crew’s accommodation 士兵舱5、货舱cargo hold 货舱cargo oil tank 货油舱container hold 集装箱舱refrigerated cargo hold 冷藏货舱liquified natural gas tank 液化天然气舱mail room 邮件舱luggage room 行李舱vehicle hold 汽车舱6、液舱liquid tank 液舱fuel oil tank 燃油舱lubricating oil tank 滑油舱overflow fuel oil tank 燃油溢油舱overflow lubricating oil tank 滑油溢油舱fuel oil sump tank 污燃油舱lubricating oil sump tank 污滑油舱circulating lubricating oil tank 循环滑油舱ballast water tank 压载水舱fresh water tank 淡水舱distilled-water tank 蒸馏水舱feed water tank 锅炉水舱stabilizing tank , anti-rolling tank 减摇水舱bilge tank 污水舱7、贮藏室store 贮藏室awning store 天幕贮藏室lamp store 灯具贮藏室hawser store 帆缆间paint store 油漆间provision store 粮食库refrigerating chamber 冷藏库8、其他fore peak 首尖舱after peak 尾尖舱bottom side tank 底边舱top side tank 顶边舱wing tank 边舱lower hold 底舱double-bottom compartment 双层底舱cofferdam 隔离空舱command station 总指挥所secondary command station 预备指挥所三、船体几何形状和尺度1、一般molded hull surface 船体型表面ship’s form, hull form 船体线型molded volume, volume of molded form 型排水体积bare hull, naked hull 裸船体appendages 附体2、基准面和基准线principal coordinate planes 主坐标平面base plane 基平面center(-line)plane, central longitudinal plane, longitudinal middle(-line)plane 中线面midstation plane 中站面molded base line 基线3、船体尺度principal dimensions 主尺度length overall, overall length 总长extreme length 最大长length between perpendiculars 垂线间长length overall submerged 浸体长waterline length 水线长designed waterline length 设计水线长load waterline length 满载水线长molded breadth 型宽waterline breadth 水线宽designed waterline breadth 设计水线宽extreme breadth 最大宽breadth overall submerged 浸体宽molded depth 型深draft 吃水molded draft 型吃水keel draft 龙骨吃水designed draft 设计吃水fore draft 首吃水aft draft 尾吃水mean draft 平均吃水navigational draft 外形吃水loaded draft 满载吃水light draft 空载吃水draft mark 吃水标志4、型线图与几何形状lines plan 型线图body plan 横剖面图sheer plan 纵剖面图half breadth plan 半宽水线图forward perpendicular 首垂线after perpendicular 尾垂线grid 格子线ordinate station 站midstation 中站station ordinates 站线molded lines 型线mathematical lines 数学型线offsets 型值preliminary offsets 原始型值returned offsets, finished offsets 完工型值table of offsets 型值表preliminary table of offsets 原始型值表returned table of offsets, finished table of offsets 完工型值表transverse sections 横剖面midship section, amidship section 中横剖面maximum section, fullest section 最大横剖面waterplane 水线面buttocks 纵剖线body lines 横剖线diagonal 斜剖线bilge diagonal 舭斜剖线profile 外廓线waterline 水线designed waterline 设计水线loaded waterline 满载水线parallel middle-body length 平行中体长length of entrance 进流段长length of run 去流段长half angle of entrance 半进流角deck line 甲板线deck line at side, deck side line 甲板边线deck line at center, deck center line 甲板中线sheer line 舷弧线molded depth line 舷弧基准线sheer 舷弧sheer at forward perpendicular 首舷弧sheer at after perpendicular 尾舷弧average sheer, mean sheer 平均舷弧sheer at deck center 脊弧camber, round of beam 梁拱camber curve 梁拱线deadrise, rise of floor, rise of bottom 舭部升高bilge radius 舭部半径keel line 龙骨线rake of keel, keel rake, designed drag, keel drag 龙骨设计斜度half-siding 龙骨水平半宽floor line 船底斜升线knuckle line 折角线tumble home 内倾flare 外倾flare 外飘immersed transom beam 方尾浸宽immersed transom draft 方尾浸深5、船型系数与尺度比coefficients of form 船型系数block coefficient 方形系数prismatic coefficient longitudinal coefficient, cylindrical coefficient 棱形系数vertical prismatic coefficient 垂向棱形系数waterline coefficient waterplane coefficient 水线面系数midship section coefficient 中横剖面系数length breadth ratio 长宽比length depth ratio 长深比breadth depth ratio 宽深比breadth draft ratio 宽度吃水比draft depth ratio 吃水型深比6、船体各部位fore body 前体after body 后体parallel waterline 水线平行段waterline beginning 水线前段waterline ending 水线后段parallel middle body 平行中体entrance 进流段run 去流段shoulder 肩forward shoulder 前肩after shoulder 后肩bilge 舭soft chine 圆舭hard chine 尖舭transom 方尾端面overhang 悬伸部counter 尾伸部forefoot 首踵aftfoot 尾踵bossing, shaft bossing, shell bossing 轴包套short bossing 短轴包套long bossing 长轴包套deadwood 尾鳍7、船的首、尾及剖面型式clipper bow, fiddle bow, cutwater bow, knee bow, overhanging bow 飞剪型首raked bow 前倾型首vertical bow 直立型首icebreaker bow 破冰型首bulbous bow, bulb bow 球鼻型首elliptical stern 椭圆型尾transom stern 方型尾cruiser stern 巡洋舰型尾tunnel stern 隧道型尾bulb section 球臌型剖面U-shaped section U型剖面V-shaped section V型剖面四、船舶重量和容积量度1、排水量与重量displacement 排水量molded displacement 型排水量total displacement 总排水量light displacement, light weight 空载排水量light weight (or mass), light displacement 空船重量(或质量)standard displacement 标准排水量normal displacement 正常排水量full load displacement,loaded displacement 满载排水量maximum displacement 最大排水量designed displacement 设计排水量displacement margin 储备排水量total deadweight, gross deadweight 载重量cargo deadweight, net capacity, useful. deadweight 净载重量deadweight displacement ratio 载重系数ballast 压载2、吨位与吨位丈量tonnage 吨位register ton, vessel ton, ton 登记吨gross tonnage 总吨位net tonnage 净吨位register tonnage 登记吨位suez canal tonnage 苏伊士运河吨位panama canal tonnage 巴拿马运河吨位underdeck tonnage 甲板下吨位tween-deck tonnage 甲板间吨位tonnage of hatchways 舱口吨位tonnage measurement 吨位丈量tonnage certificate,certificate of admeasurement 吨位证书tonnage mark 吨位标志register length 登记长度register breadth 登记宽度register depth 登记深度tonnage deck 量吨甲板tonnage length 量吨长度tonnage depth 量吨深度tonnage breadth 量吨宽度exempted space 免除处所deducted space 减除处所propelling power space 推进机械处所enclosure 围蔽处所3、干舷与载重线freeboard 干舷freeboard deck 干舷甲板loadline 载重线loadline mark 载重线标志deadweight scale, displacement scale 载重量表尺4、容积与积载tank capacity 液舱容积cargo capacity 货舱容积grain capacity, grain cargo capacity, grain cubic 散装舱容积bale cargo capacity, bale capacity, bale measure, bale cubic 包装舱容broken stowage, breakage 亏损舱容ullage 膨胀舱容capacity curve 容积曲线capacity plan 舱容图stowage 积载stowage factor 积载因数七、船体结构1、一般hull 船体hull structure, ship structure 船体结构main hull 主船体shell plate 外板strake 列板in and out system 内外搭接式inner strake 内列板outer strake 外列板clinker system 鱼鳞式joggled plating 折曲式flush system 平接式framing 骨架transverse system of framing 横骨架式longitudinal system of framing 纵骨架式combination system of framing 混合骨架式ice strengthening 冰区加强ice belt 冰区带girder, stringer 纵桁longitudinal 纵骨2、船底结构single bottom 单底double bottom 双层底keel 龙骨bar keel 方龙骨plate keel 平板龙骨bottom plate 船底板garboard strake 龙骨翼板bilge strake 舭列板floor, bottom transverse 肋板solid floor 主肋板bracket floor, open floor 框架肋板water tight floor 水密肋板oil tight floor 油密肋板bottom frame 船底肋骨bottom longitudinal 船底纵骨bottom center girder, vertical keel 中底桁duct keel 箱型中底桁bottom side girder 旁底桁half depth girder 半高底纵桁keelson 内龙骨center keelson 中内龙骨side keelson 旁内龙骨inner bottom 内底inner bottom plate 内底板margin plate 内底边板reverse frame 内底横骨inner bottom longitudinal 内底纵骨bilge bracket 舭肘板bilge well 污水井bilge keel 舭龙骨docking keel 坞龙骨3、舷侧结构side plate 舷侧外板sheer strake 舷顶列板rounded sheer strake 圆弧舷顶列板frame 肋股web frame side transverse 强肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨frame spacing 肋骨间距side longitudinal 舷侧纵骨side stringer 舷侧纵桁fender 护舷材5、艏、船艉结构stem 艏柱stern frame, stern post 艉柱rudder post 舵柱propeller post 螺旋桨柱ruder horn 挂舵臂sole piece 艉柱底骨gudgeon 舵钮bow transom plate 首封板stern transom plate 尾封板boss plate 轴包板bossing, shaft bossing, shell bossing 轴包套propeller strut propeller bracket 艉轴架single armed propeller strut 单臂尾轴架A-bracket 人字架deadwood 尾鳍peak frame 尖舱肋骨cant frame 斜肋骨panting arrangement 强胸肋骨panting beam 强胸横梁anchor recess 锚穴hawse pipe 锚链筒chain pipe 锚链管anchor bed 锚床5、甲板、支柱deck 甲板strength deck 强力甲板bulkhead deck 舱壁甲板upper deck 上甲板second deck 第二甲板lower deck 下层甲板bare deck 裸甲板sheathed deck 覆材甲板raised deck 升高甲板raised fore deck 首升高甲板raised quarter deck 尾升高甲板sponson deck 舷伸甲板platform deck 平台甲板deck plate 甲板板stringer plate, deck stringer 甲板边板deck framing 甲板骨架deck beam 横梁cant beam 斜梁strong beam, deck transverse 强横梁hatch side cantilever 舱口悬臂梁hatch end beam 舱口端横梁half beam 半梁beam knee 梁肘板deck girder 甲板纵桁hatch side girder 舱口纵桁deck longitudinal 甲板纵骨stringer angle 舷边角钢hatch 舱口cargo hatch 货舱口oil tank hatch 油舱舱口escape hatch 应急舱口excess hatch 出入舱口hatch coaming 舱口围板companion 舱口围罩tank cleaning opening 洗舱孔scupper 甲板排水孔gutter way 甲板水沟breakwater 挡浪板pillar, stanchion 支柱tubular pillar 管型支柱built up pillar 组合支柱6、舱壁、轴隧、围井bulkhead 舱壁transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁centerline bulkhead 中纵舱壁slopping bulkhead 斜舱壁collision bulkhead 防撞舱壁after peak bulkhead 尾尖舱舱壁tweendeck bulkhead 甲板间舱壁watertight bulkhead 水密舱壁oil tight bulkhead 油密舱壁plane bulkhead 平面舱壁corrugated bulkhead 槽型舱壁double plate bulkhead 双板舱壁partial bulkhead 局部舱壁partition bulkhead, screen bulkhead 轻舱壁swash bulkhead 制荡舱壁swash plate 制荡板bulkhead plate 舱壁板stiffener 扶强材horizontal girder 水平桁vertical web 竖桁cross tie 边舱撑杆shaft tunnel 轴遂tunnel recess 轴遂端室trunk 围井。
船舶名词知识点总结一、船舶基础知识1. 船舶类型船舶根据用途和特点可分为货船、客船、油船、拖轮、渔船、军舰等不同类型。
2. 船舶结构船舶主要由船体、甲板、船尾、船首、船舱、船桅、船舵、吊杆等部位构成。
3. 船舶尺寸船舶尺寸包括船长、船宽、吃水深度、型深等指标。
4. 船舶载重量船舶载重量是指船舶能够承载的最大货物重量,通常以吨为单位。
二、船舶航行知识1. 船舶航行方式船舶航行方式有航行、靠泊、锚泊、停泊、横泊等不同形式。
2. 船舶航速船舶航速是指船舶航行的速度,通常以节为单位,1节等于每小时1.852公里。
3. 船舶航迹船舶航迹是指船舶在海洋上航行的路径。
4. 船舶航行安全船舶在航行中需要注意避碰规则、海图使用、气象信息等,以确保航行安全。
三、船舶动力装置1. 船舶主机船舶主机是指推动船舶的主要动力装置,通常有柴油机、蒸汽机、涡轮机等不同类型。
2. 船舶辅机船舶辅机是指为船舶提供辅助动力的装置,包括发电机、压缩机、泵等设备。
四、船舶导航设备1. 船舶罗经船舶罗经是指船舶用来确定方向的装置,分为磁罗经和陀螺罗经两种类型。
2. 船舶雷达船舶雷达是通过电磁波进行航行和目标监测的设备,可用于判断目标距离、方位和速度。
3. 船舶GPS全球定位系统(GPS)是一种卫星导航系统,可为船舶提供准确的位置信息。
五、船舶通信设备1. 船舶对讲机船舶对讲机是船舶上用于通信的设备,可用于船舶内部通话和与其他船舶的通讯。
2. 船舶VHF船舶VHF是一种用于船舶通信的短距离无线电设备,可用于船舶间通讯和与岸上基站的通讯。
六、船舶安全设备1. 船舶救生设备船舶救生设备包括救生筏、救生衣、救生圈、救生艇等,在遇到紧急情况时可用于撤离船员。
2. 船舶消防设备船舶消防设备包括灭火器、消防栓、消防泵等,在火灾发生时可用于扑灭火灾。
七、船舶维护和管理1. 船舶维护船舶维护包括船体维护、设备维护、油漆维护等,以确保船舶的安全和性能。
2. 船舶管理船舶管理包括船舶运营管理、船舶维修管理、船舶人力资源管理等,以提高船舶的整体运营效率。
ship相关单词一、ship([ʃɪp],n. 名词;v. 动词)1. 名词含义。
- 船,舰。
例如:The ship is sailing on the ocean.(船正在大洋上航行。
)2. 动词含义。
- 运送;乘船;以船运送。
例如:They ship the goods by train.(他们用火车运送货物。
)二、shipment([ˈʃɪpmənt],n. 名词)- 装货;装载的货物。
例如:The shipment of goods arrived yesterday.(货物的装运昨天到达了。
)三、shipping([ˈʃɪpɪŋ],n. 名词)- 船舶;航运;海运。
例如:The shipping industry is very important for international trade.(航运业对国际贸易非常重要。
)四、shipwreck([ˈʃɪprek],n. 名词;v. 动词)1. 名词含义。
- 海难;遇难船。
例如:Many treasures were found in the shipwreck.(在海难船只中发现了许多财宝。
)2. 动词含义。
- 使失事;使毁灭;使失败。
例如:The storm shipwrecked the small boat.(暴风雨使小船失事了。
)五、shipbuilder([ˈʃɪpbɪldə(r)],n. 名词)- 造船工程师;造船者。
例如:The shipbuilder is famous for his excellent skills.(这位造船者以其精湛的技艺而闻名。
)六、shipyard([ˈʃɪpjɑːd],n. 名词)- 造船厂;船坞。
例如:There are many workers in the shipyard.(造船厂有许多工人。
)。
海運業專有名詞1.VESSEL、PORT 船舶、港口CONTAINERSHIP 貨櫃船BARGE ( LIGHTER ) 駁船BERTH 泊位DOCK 船塢WHARF 碼頭BAY 艙HATCH (大艙) TIER (橫)層ROW (縱)行DECK 甲板SPACE 艙位TUG BOAT 拖船PILOT BOAT 領港船['ɛstə,met【ETA ESTIMATED TIME OF ARRIV AL 預定到達時間ETD ESTIMATED TIME OF DEPARTURE 預定離開時間ETB ESTIMATED TIME OF BIRTH 預定靠泊時間ETC】ESTIMATED TIME OF COMMENCEMENT 預定開工時間ESTIMATED TIME OF COMPLETENESS 預定完工時間CAPTAIN. MASTER 船長OFFICER ['ɔfəsɚ]高級船員CREW 船員(水手) LASHING ['læʃɪŋ]绑定SHORING 固定TRIMMING 平艙TEU TWENTY FOOT EQUIV ALENT UNIT 20呎貨櫃單位FEU FORTY FOOT EQUIV ALENT UNIT 40呎貨櫃單位2.OPERATION 作業EQUIPMENT & FACILITIES 設備及機具TERMINAL ['tɝmən!]貨櫃基地1.DEPOT ['dipo]貨櫃場2.INLAND DEPOT 內陸貨櫃場3.ON DOCK CY 岸邊堆場(码头堆场)4.OFF DOCK CY 內陸堆場【-WAREHUOSE】1.GENERAL 普通2.REEFER 冷凍3.DANGEROUS CARGO 危險品4.BULK [bʌlk]散裝5.CUSTOMS(海关、风俗习惯)JOINTLOCK 联锁6.BONDED ['bɑndɪd]保稅的CRAVE(N/V渴望)起重機1.SHIP’S CRANE [krein](SHIP’S GEAR) 船舶(上)起重机2.MOBILE CRANE 移動式起重机3.FLOATING CRANE 水上起重机4.GANTRY CRANE 岸上、橋式起重機FORK LIFT 堆高機TOP LOADER 堆積機R/T RAIL TRANSTAINER 軌道式門式起重機T/T TIER TRANSTAINER 輪胎式門式起重機S/C STRADDLE CARRIER 跨載機SPREADER 伸展架TRAILER 拖車CHASSIS 拖車架TRACTOR 拖車頭CONTAINER 貨櫃FLATFORM 月台TARE WEIGHT 皮重PAY LOAD 可裝貨重PREFIX ['pri,fɪks]CODE 貨櫃識別記號PRE - COOLING 預冷PTI PER- TRIP INSPECTION 預先溫度檢查STUFFING 裝櫃( V ANNING )UNSTUFFING 拆櫃( DEV ANNING )CARGO ACCEPT TERM 收貨條件1.LCL LESS THAN CONTAINERLOAD 併櫃2.CFS CONTAINER FREIGHTSTATION 併櫃3.FCL FULL CONTAINER LOAD整櫃4.CY CONTAINER YARD 整櫃3.TRANSPORTATION 運輸CARRIER 船舶運送業MON CARRIER 公共運送人2.FEEDER CARRIER 支線運送人3.OCEAN GOING CARRIER 長程運送人CHARTER PARTY 租傭船契約1.TIME CHARTER 論時傭船2.VOYAGE CHARTER 論程傭船3.BARE BOAT CHARTER 空(光)船租賃OPERATION (裝卸貨) 作業1.MID-STREAM OPERATION 中流作業2.SHIPSIDE OPERATION 船邊作業3.TERMINAL OPERATION 貨櫃場作業SERVICE 航線1.LINER SERVICE 定期航線2.FIXED DAY SERVICE 固定日航線3.WEEKLY SERVICE 每週定期航線4.TRAMP SERVICE 不定期航線5.DIRECT SEREVICE (NON-TRANSIT) 直航航線6.FEEDER SERVICE 支線航線7.WAY-PORTS SERVICE 順道航線8.DOOR-TO-DOOR SERVICE 戶到戶航線9.INTERPORTS SERVICE 亞洲近海航線10.TRANSPACIFIC SERVICE 美洲越太平洋航線4.SALES 營業FREIGHT 運費1.MEASUREMENT TON/BASIS 材數噸2.WEIGHT TON 重量噸3.BOX RATE 包櫃價4.SLOTTAGE 艙位租金(成本)5.GRI (GENERAL RATE INCREASE)全面運費調升6.ALL IN RATE 總價SURCHARGE 附加費1.BAF BUNKER ADJUSTMENT FACTOR 油料附加費( BUNKER SUR CHARGE )2.CAF CURRENCY ADJUSTMENT FACTOR 匯率附加費( CURRENCY SUR CHARGE)3.THC TERMINAL HANDLING CHARGE 櫃場調櫃費4.CHC CONTAINER HANDLING CHARGE 貨櫃調櫃費5.YAS YEN APPRECIATION SURCHARGE 日圓升值附加費6.DEMURRAGE 延滯費(重櫃在場)7.DETENTION 延還費(空櫃在外)8.HANDLING ( TRANSIT ) 處理(轉運)SALES TERM 銷售條件1.C & F COST & FREIGHT 成本&運費2.C.I.F. COST, INSURANCE, FREIGHT抵岸價格、起岸價格3.F.O.B. FREE ON BOARD 離岸價格SHIPSIDE TERM 船邊條款1.BERTH TERM 裝卸費船東支付2.FREE IN/ FREE OUT ( FIO ) TERM 裝卸費船東免責3.CY TERM 貨櫃場交貨4.TACKLE TERM 船邊交貨AGREEMENT 協定、CONTRACT 契約1.SERVICE AGREEMENT 航線協定2.COOPERATION AGREEMENT 合作協定3.CONSORTIUM 策略聯盟4.GLOBAL ALLIANCE 環球聯盟CONFERENCE 同盟1.JTJCCDA JAPAN TAIWAN JAPANCONTAINERCONFERENCE DISCUSSION ASSOCIATION台日貨櫃同盟協定2.TWRA TRANS PACIFICWESTBOUND RATEAGREEMENT 跨太平洋西向運費協定3.FMC FEDERAL MARTIMECOMMISSION聯邦海事局4.IDIA INTRA ASIA DISCUSSIONAGREEMENT東亞地區(船東)諮商協定5.SARA SOUTH-ASIA RATEAGREEMENT南亞次大陸地區運費協定6.IRA INDEPENDENT RATEAGREEMENT西亞、波斯灣地區運費協定5.DOCUMENT 文件S/O SHIPPING ORDER 艙位簽載單、託運單CLP CONTAINER LOAD PLAN 裝載計劃EIR EQUIPMENT INTERCHANGE RECEIPT 貨櫃設備交接清單M/F MANIFEST 艙單A/N ARRIV AL NOTICE 到貨通知單D/O DELIVERY ORDER 小提單L/G LETTER OF GUARANTEE 切結書L/C LETTER OF CREDIT 信用狀B/L BILL OF LADING 提單1.CLEAN B/L 清潔提單FOUL B/L不潔提單2.ORIGINAL B/L 正本提單COPYB/L 副本提單3.HOUSE B/L 分提單4.MASTER B/L 主提單5.THROUGH B/L 聯運提單6.NEGOTIABLE B/L 可轉讓提單7.NON-NEGOTIABLE B/L 不可轉讓提單8.(SEA) WAYBILL 直交提單(電放提單)6.OTHERSTOPPING 加裝CO-LOAD 混裝OWNER 船東CHARTERER 租傭船人PRINCIPAL 本人(通常為船舶所有人或船東)AGENT 代理行CUSTOMS BROKER 報關行CONSOLIDATOR 貨運併裝業FORW ARDER 海運承攬運送業NOVCC (Non-vessel-Operating Common Carrier) 無船公共運送人。
目录一、船舶辅机(附船舶减摇及海上补给装置)1.一般2.船用泵3.船用风机4.船用压缩机5.船用油分油机6.甲板机械一般7.操舵系统与舵机8.系船机械9.装卸机械10.拖缆机、起艇机11.海水淡化装置12.船舶减摇装置13.海上补给装置二、船舶系统1.一般2.油船系统3.舱底和压载水系统4.甲板排水及疏水系统5.冷藏与制冷系统6.通风系统7.空调系统8.供暖及生活用水系统9.灭火系统10.注入、空气与测量管系一、船舶辅机1.一般1 船舶辅机marine auxiliary machinery船上除主机、主锅炉以外所有机械设备的统称2 机舱辅机engine-room auxiliary machine装设于船舱内,除甲板机械以外为主机及其他系统服务的机械3 甲板机械deck machinery一般装置在甲板上,为船舶航行、系泊、装卸及拖曳等服务的机械。
如舵机、锚机、绞缆机、起货机、起艇机等2. 船用泵4 船用泵marine pump,ship’s pump符合船舶规范规定或船用技术条件要求的各种供船舶使用的泵的统称5 主泵main pump主要和经常使用的泵。
如主给水泵、主冷却水泵等6 辅泵auxiliary pump,donkey pump作为待用和起辅助作用的泵。
如辅给水泵、辅冷却水泵等7 值班泵duty pump,service pump工作中的泵8 待用泵standby pump作好起动准备,随时可以投入使用的泵。
一般与值班泵轮换使用9 起动用泵starting up pump供起动时使用的泵,如向锅炉注水的泵、起动时用的滑油泵等10 首尖舱泵forepeak pump抽送首尖舱积水、具有独立管系的泵11 减摇泵anti-roll pump用于减摇水舱系统的泵12 纵倾平衡泵trim (ming)pump抽送舱柜中的水或油类以调节船舶纵倾平衡的泵13 横倾平衡泵list pump将水或油从左或右舷液舱抽送到右或左舷液舱以调节船舶横倾平衡的泵14 甲板冲洗泵deck wash pump,flushing pump抽送冲洗甲板用水的泵15 停泊泵port(duty)pump,harbor pump16 舱底泵bilge pump一般具有自吸能力,用以将舱底水抽送到舷外的泵17 压载泵ballast pump用于压载水舱注水或排水的泵18 专用清洁压载泵clean(permanent water)ballast pump油船上抽送专用清洁压载水的泵19 洗舱泵butterworth pump,tank cleaning pump油船上抽送清洗油舱用水的泵20 清舱泵cargo oil stripping pump船上抽送油舱中残余剩油的泵21 总用泵general service pump作日常杂用的泵,也常作为其他专用泵的待用泵22 卫生泵sanitary pump抽送卫生用水的泵23 消防泵fire pump抽送消防用水的泵24 应急消防泵emergency fire pump25 可移式消防泵机组portable fire(fighting)unit由独立动力机如汽油机、柴油机等驱动的,非固定安装并可用人力搬移的消防泵机组26 泡沫原液泵concentrate pump泡沫灭火系统中用作抽送泡沫原液的泵27 泡沫液循环泵泡沫灭火系统中将泡沫液自贮存舱吸出并使泡沫液与水混合成泡沫混合液的泵28 粪便泵sewage pump抽送粪便等污物的泵29 热水循环泵hot water circulating pump生活用热水系统中,使热水通过热水器循环,以防止热水冷却的泵30 淡水泵fresh water pump抽送淡水的泵31 海水泵sea-water pump抽送海水的泵32 饮水泵drinking water pump,(portable water pump)抽送饮用的泵33 疏水泵drainage pump排去船上积水的泵34 救助泵salvage pump打捞或救助用的泵35 液货泵liquid cargo pump抽送液体货物的泵36 货油泵cargo (oil)pump油船上抽送货油的泵,有时亦兼作压载泵37 泥泵dredging pump挖泥船上抽送泥浆的泵38 增压泵booster pump,boosting pump产生一定压力,为另一泵建立吸入条件的泵。
VOCABULARY3-roller bending machine 三弯机abandon v. 弃船abolish v. 消除ABS 美国船级社acceleration n. 加速度accelerometer n. 加速度表accommodate v. 容纳accommodation deck起居(住舱)甲板accuracy n. 精度accurate synchro device准同步装置acetylene cutter 气割机acid-pickling n. 酸洗acoustics n. 音响效果adhesiveness n. 粘附力adjacent a.相邻的adjust v. 调节administration n. 行政管理admit v. 接纳adopt v. 采纳,采用affiliated factory 分厂,附属工厂aforementioned a.前述aft a. adv. n. (在)船艉aft peak 艉尖舱after service 售后服务ahead n. 正车air bottle 空气瓶air compressor 空压机air reservoir 气瓶air siren 汽笛air-tight test 气密实验alarm bell 警铃alignment n. 找中all waves 全波allowance n. 允值all position 全方位alternating current ( A.C.) 交流电ammonia n. 氨amplify v. 放大an automatic production line自动生产线analogous output 模拟输出analogue computer 模拟计算机anchor n. 锚anchor chain (cable chain)锚链anchor handling 锚操纵anchor windlass (chain windlass) 起锚机anchorage buoy 系泊浮筒angular n. 角度antenna n. 天线anticorrosion precaution 防腐措施apparatus n. (pl. apparatus or apparatuses)仪器,器械,装置appearance n. 外观approval n. 批准,认可approve vt. 认可arbitrate v. 仲裁arc n. 弧度arduous a.艰难的arrange v. 布置,安排asbestos n. 石棉assemble v. 装配Assemble Language 汇编语言assembly n. 装配astern n. 倒车atmospheric survey 大气环流调查atomic power 原子能atomize v. 雾化authority n. 当局automatic control device自动控制装置automatic production line自动生产线automatic steering 自动操舵automatic submerged arc welding自动埋弧焊automatic telephone 自动电话aux. boiler 副锅炉aux. engine 辅机aux. engine room 辅机舱aux. machinery 辅机auxiliary means 辅助手段auxiliary system 辅助系统axial push 轴向推力backing n. 衬垫ballast piping 压载水管系ballast pump 压载泵ballast system 压载系统ballast water 压载水base n. 基准base point n. 基准点basic design 基本(方案)设计basic metal 母材battery unit 蓄电池组beam n. 波束beam n. 横梁bearing n. 轴承bearing hole n. 轴承孔bedplate n. 机座bell set 铃组bending machine 冷弯机berth n. (水平)船台,(船上)床铺berth or slipway fabrication船台装配bilge n. 舱底水bilge keel 舭龙骨bilge plate 舭板bilge pump 舱底水泵bilge system 舱底水系统binary system 二进位制blank n. 毛胚block n. 分段block or section fabrication分段或总段装配blood vessel 血管blower 风机blue collar worker 蓝领,工人boat deck 艇甲板bollard n. 带缆桩bolt n. 螺栓bolthead n. 螺栓头bottom n. 船底bottom plate 底板bottom structure 底板结构bow n. 船艏bow &stern structure 艏艉结构bow section 艏段branch company 分公司,子公司branch system 分系统bridge n. 桥楼bridge control 桥楼控制broadcast n. v. 广播broadcast station 广播站bronze sleeve 青铜套筒bulbous bow 球鼻艏bulk cargo 散装货物bulk-cargo carrier 散装货船bulkhead n. 隔舱壁bulkhead structure 隔舱壁结构bushing n. 衬垫butt joint 对接接头cabin n. 舱室cable fixture 电缆夹具calculation n. 计算calculator n. 计算器calibrate v. 校正calibration n. 校正cam n. 凸轮cam follower 凸轮附件camber n. 梁拱camshaft n. 凸轮轴capstan windlass(anchor winch)锚绞盘cargo n. 船货cargo oil 货油cargo –hold n. 货舱cargo-lifting n. 起货casing n. 罩壳cast iron piece 铸铁件casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n.性能,特性,特征charge v. 充(电,气)check n. v. 检验chemical medium 化学介质China Classification Society(CCS)中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子,团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环clutch n. 离合器CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity综合生产能力compressed air 压缩空气compression (power)stroke n.压缩冲程computer control console计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contract n. 合同contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养,培育current n. 电流current n. 洋流,水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n.载重量,吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货,交船delivery n. 交船,交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称,牌号designation n. 目的地detail design 详细(施工)设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone对讲电话,直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端,争执distribute v. 分布distribute v. 分配,配电distribution n. 配电distribution box 分电箱distribution panel 区配电板distribution switch 配电开关distribution system n. 配电系统division n. 划分DNV 挪威船级社Dock n. 船坞dock trial 码头试验docking winch 带缆绞车Doppler effect 多普勒效应Doppler frequency offset多普勒频移Doppler sonar log多普勒声纳计程仪double bottom 双层底double-action a.双作用down-vertical welding 下行焊draft(draught)n. 吃水drainage n. 疏水,泄水drawing n. 图纸drawing instrument 绘图仪drift v. 漂移drinking water 饮用水drip-proof type 防滴式drive n. 传动drive mechanism 传动机构drive mechanism 传动装置drive unit 传动装置driven shaft 从动轴dry v. 烘干drydock n. 干船坞dynamic –pressure type 水压式echo signal 返回信号echo sounder 回声测深仪economic effect 经济效益edge preparation 边缘加工edge processing 边缘加工edger n. 刨边机eject v. 喷射elapse v. (时光)消逝electric brain 电脑electric load 负荷electrical arc 电弧electrical compass 电罗经electrical drive 电力托动electrical energy 电能electrical impulse 电脉冲electrical power 电力electrical shedding 放电electrical signal 电器信号electrical slag welding 电焊渣electrical unit 电器装置electrical user 电器设备electrical-driven a. 电动的electrician n. 电工electricity outfitting 电舾electrode n. 焊条electromagnetic contactor电磁接触器electromagnetic induction 电磁感应electromagnetic log 电磁计程仪electromagnetic sensor 电磁传感器electronic computer 电子计算机electronics n. 电子(学)element n. 机械零件element n. 要素emerge v. 崛起,兴起emergency control 应急控制emergency network 应急电网emergency power station 应急电站emergency radio transmitter应急无线电发信机emergency steering 应急操舵emergency switchboard 应急配电板emergency telegraph 应急传令钟emergent discharge 应急排放emergent service 应急使用enclose v. 封闭encounter v. 遭遇energy convertor 换能器engine foundation (engine seat )机座engine frame 机架engine oil 机油engine outfitting 机舾engine space 机舱engineer n. 轮机员engineer n. 工程师engineering and technical team工程技术队伍engineer vessel 工程船engine-room 机舱ensure v. 确保enterprise n. 企业EO 无人机舱equipment n. 设备error n. 误差essence n. 实质,本质evolve v. 渐进,进化,演变excessive a. 过量的,极度的excitation n. 励磁excite v. 激励exhaust port 排气口exhaust stroke 排气冲程exhaust valve 排气阀expand v. 扩张,扩建expansion n. 展开图expansion stroke 膨胀(作工)冲程expansion tank 膨胀箱experiment n. 实验exterior force 外力extinguish v. 灭火F.O.meter 燃油流量计F.O.tank 燃油舱Fabricate v. 装配,制作fabrication n. 装配facile adaptability 灵活的适应性facsimile transmission(fax)传真fairing n. 光顺体,流线体fair-lead n. 导缆孔fashioned steel 型钢fast speed (rapidity)快速性fathometer n. 侧深仪feed v. 馈给feed circuit 馈电线路fillet seam 角焊缝fillet welding 角焊filter n. 过滤器. 过滤fine a. 纤细的finished product 成品fire alarm 火警fire hazard 火灾fire pump 消防泵fire-fighting system 消防系统fire-resistant a.耐火的fixed part 固定件flash signal light 闪光信号灯flat fillet seam 平角焊缝flexibility n. 挠性flexible coupling 挠性联轴节float launching 漂浮下水floatability n. 漂浮性floating positively 正浮floating production storage unit(FPSU)浮式生产储油轮flood v. 进水floodability n. 不沉性floor plate 肋板fluctuate v. 波动fluctuation n. 波动flush v. 清洗flushing agent 清洗剂flux n. 焊剂flywheel n 飞轮foam n. 泡沫folding machine 折边机for home use 国内用forced lubrication 强制润滑forced ventilation 机械通风fore perpendicular 艏垂线forecastle n. 艏楼foreign trade 外贸forging n. 锻造formation n. 构成,结构frame n. 肋骨framework n. 框架framing block 肋骨框架分段free end 自由端freeboard n. 干舷freighter n. 货船Freon n. 氟利昂frequency n. 频率frequency difference latching频率锁定frequency regulation 调频fresh water (F.W.)淡水fresh water production plant造水装置friction resistance 摩擦阻力fuel n. 燃料fuel nozzle 喷油嘴fuel oil 燃油fuel oil (F.O.)燃油fuel pipeline 燃油管系full-load a. 满载的full-load displacement 满载排水量funnel n. 烟囱galley n. 厨房gantry n. 龙门架gas cutting 气割gas tight seal 气密密封gas turbine engine 燃气轮机gas welding 气焊gear n. 齿轮gear drive 齿轮转动geo-physical propecting vessel地球物理探测船GL 西德劳氏船级社grant v. 给予……的权利gravity centre 重心gravity welding 重力焊groove v. 开坡口ground v. 接地group n. (企业)集团growth n. 生长,发育guarantee n. v. 保证general description 概述general-purpose a.通用的generating set 发电机组geometrical characteristics 几何特征geometrical principle 几何原理gravity launching 重力下水guided-missile frigate 导弹护卫舰gyro n. 陀螺仪gyro compass 陀螺罗经,回转罗经H.D.Heavy Machinery Co. Ltd. H.D. 重机股份有限公司Halogen n. 卤素hand control 手控hand level 手柄hand steering 手动操作hand wheel 手轮handle v. 操纵harbour n. 港口,停泊harbour generator 停泊发电机hardware n. 硬件hatch trunk 舱口围壁hawsepipe n. 锚链筒he water pressure system 水压系统headquarters n. 总部,厂部headroom n. 甲板间高度heat exchanger 热交换器heating n. 供暖heavy current n. 强电heavy oil 重油heel n. 横倾hereinbelow adv. 在下文high frequency 高频high-speed boat 高速艇horizontal a.水平的,卧式的horsepower(hp) n. 马力hose n. 软管hot processing 热加工hot work 火工hull n. 船体hull cleanness 船体光顺性hull construction 船体结构hull form 船型hull line 船体线型hull structure 船体结构human brain 人脑humidify v. 增湿hydraulic a. 液压的hydraulic fluid 液压流体hydraulic machine 液压机hyperbolic curve receive双曲线定位仪identify vt.识别ignite v. 点火ignition n. 点火illumination n. 照明illustration n. 生动的说image display system 图象显示系统IMCO 政府间海事协商组织impact n. 冲击implication n. 含义impulsator n. 推动器,脉冲发生器impulse-type a.脉冲式的impurity n. 杂质inclination n. 倾斜inclination test 倾斜试验incline v. 倾斜index n. 索引indication n. 显示indicator n. 显示仪indicator n. 指示器indicator light 指示灯indicator valve示功阀inert gas 惰性气体inertia n. 惯性inertia platform 惯性平台inevitable a.不可避免的initial metacentric height 初稳心高inject n. 喷射injecting system 喷油系统injector n. 喷油器inner bottom longitudinal 内底纵骨inner bottom plate 内底板inner ring 内环input n. v. 输入inspector n. 质检员installation n. (船上)安装installation error 安装误差instancy speed 瞬时速度instrument n. 仪表,仪器insulating material 绝缘材料insulation n. 绝缘intake n. 吸入intake port 汲气口intake valve 进气阀integral casting 整体浇铸intention n. 意向intercommunication (intercom)n.内通,内部通讯interfering moment 干扰力矩intermediate bearing 中间轴承intermediate shaft 中间轴internal combustion engine 内燃机international authorities 国际当局Internet 因特网(国际互连网)introduce v. 引进,引入,介绍iron powder electrode 铁粉焊条jig n. 胎架joint design 联合设计journal n. 轴颈keel n. 龙骨keel plate 龙骨板keep station 定位kerosene test 煤油实验key enterprise 骨干企业kilohertz 千赫kinetic energy 动能knot n. 节labyrinth n. 迷宫,曲径land-based a. 路基的landing-place n. 码头lap joint 搭接接头large-computer(mainframe computer) n. 大型(计算)机,主机lay v. 敷设length n. (一)节,(一)段level n. 液位level gauge 液位计level relay 液位继电器license n. 许可证life line 生命线life-belt n. 救生圈life-boat n. 救生艇life-jacket n. 救生衣life-or-death a.生死攸关的life-raft n. 救生筏life-saving n. 救生lifting capacity 起重能力light current 弱电lighting n. 照明light-ship displacement (light-load displacement)轻载排水量lines lofting 线型放样lines offsets 型值lines plan 线型图lining n. 衬垫load distribution 负荷分配load line mark 载重线标志load transfer 负荷转移local strengthening 局部加强locate v. 定位lock washer 锁紧垫片lofting n. 放样log n. 计程仪logical a.逻辑的long bridge 长桥楼longitudinal a.纵向的longitudinal (uniflow)scavenge直流扫气longitudinal bulkhead 纵隔舱壁longitudinal framing 纵向构架loop n. 回路loop antenna 环状天线Loran receiver 劳兰定位仪Loudspeaker n. 扬声器low speed 低速lower deck 下甲板LR 英国劳氏船级社lube oil 润滑油lube oil(L.O.)滑油lube oil pump 滑油泵lubricant n. 润滑剂lubricant film 润滑油膜lubricating oil 滑油lubrication system 滑油系统M.E.engine room 主机舱Machine v. 机加工machinery n. 机械machinery set 机组machinery workshop 机电车间machining n. 机加工machining workshop 机加工车间magnetic compass 磁罗经magnetic field 磁场magnetic needle 磁针magnetic object 磁性物体magnifier n. 放大器magnify v. 放大magnitude n. 大小main bearing 主轴承main engine (ME) 主机main generating set 主发电机组Main Group 1 第一大部分main hull 主船体main network 主电网main power station 主电站main switchboard 主配电板maintenance n. v. 维护,保养marker n. 厂商man power resource 人力资源management n. 生产管理maneuver v. n. 操纵maneuverability n. 操纵性maneuvering console 操纵台maneuvering system 操纵系统manual work 手工劳动manufacture n. &v. 生产,制造marine crane 船用起重机marine diesel engine 船用柴油机marine engineer 机电工程师marine engineering research institute造机研究所marine geological research vessel海洋地质调查船mark v. 标出mast lightmaster controller 主令控制器Master degree 硕士学位material n. 材料material marking 下料mathematical a.数学的mathematical lofting skill数学放样技术maximum(max.)n. 最大means n. 手段,工具measurement laboratory 计量实验室measuring meter 测量仪表measuring point 测量点mechanical energy 机械能mechanical launching 机械下水mechanical processing 机加工mechanical unit 机械装置medium speed 中速medium wave 中波medium-computer n.中型(计算)机member n. 构件memory n. 储存器,内存memory and storage system储存系统merchant ship 民用船mercury n,水银meridian n. 子午线metacentre n. 稳心metal recovery 金属回收率metallic equipment 冶金设备microclimate n. 小气候microcomputer n. 微机microprocessor n. 微处理器midship n. a. adv. 舯部military ship 军用船miller n. 铣床minicomputer n. 小型(计算)机minimize v. 降至最低minus push 负推力minus value 负值miscellaneous a. 杂项的mobilize v. 动员model case 样箱model plate 样板model rod 样棒moderate a. 中型的modern enterprise system现代企业制度modus n. 操纵法(pl. modi)monitor v. 监视monitoring device 监控装置moor v. 系泊motive power 原动力motor n. 电动机mould loft 放样台mouth n. 河口moving part 运动件multi-purpose a.多用途的,综合的multi-stage n. 多级mutual benefit 互惠互利nautical mile 海里naval architect 造船设计师navigating instrument 导航仪器navigating zone 航区navigation computer 导航计算机navigation equipment 导航设备navigational light 航行灯navy n. 海军navy underway replenishment ship海军航行补给船NC cutting machine 数控切割机nerve cell 神经细胞nesting n. 套料network n. 电网nil n. 零,无NK 日本海事协会non –ferrous metal 有色金属non-restrictive a.自由的,不受限制的non-standard product 非标产品non-transparent a. 不透明的normal displacement 正常排水量normal shipping 正常营运nozzle n. 喷嚏numbering system 计算系统numeral n. 数字numerical control (NC)数控numerical control cutter 数控切割机nut n. 螺母observation n. 观察occasion n. 盛事,盛举ocean-going vessel 远洋船oceanographic research vessel海洋调查船offshore service 近海作业oil charging piping 注油管系oil consumption 油耗oil filling port 注油口oil mist 油雾oil refinery 炼油厂oil tanker 油船oil-resistant a.耐油的oil-tight n. 油密Omega/satellite integrated navigation instrument 奥米加/卫星导航系统one-side welding单面焊接,双面成形one-way a.单向的open chamber 开放式燃烧室open circulation 开放循环opening n. 开口operating cycle 工作周期operation n. 施工operation n. 运行,运转operation surroundings 作业环境operator n. 操纵员opportunity n. 机遇optical projector 光学仪器optics n. 光学orbit n. 轨道order n. v. 订单,定购oscillation n. 振荡oscillation current 振荡电流outboard adv. 向舷外outer appearance 外观outer ring 外环outfitting n. 舾装output n. 输出overload v. 过载owner n. 船东owner’s representative船东代表oxide n. 氧化皮paint n. 油漆pain-taking a.艰巨的painting n. 涂装painting n. 涂装,油漆工艺palletizing management 托盘管理parallel n. 并联v. 并车parallel of generators 发电机并车parameter n. 参数part n. 部件,机械部件part fabrication 部装particle n. 颗粒party n. (谈判或合同之)一方passage n. 通道passageway n. 通道passenger-cargo vessel 客货船performance n. 性能permanently adv. 永久的perpendicular n. 垂线personnel n. 全体人员personnel n. 人员,人事phase angle 相角phase sequence 相序phase –sensitive rectifier相敏整流器physical quantity 物理量physical-chemical experiment理化实验physical-chemical experimental center理化中心实验室pillar n. 支柱pilot n. 驾驶员,领航员,舵轮pipe connection 管子接头pipe flange 管子法兰piping system 管系piston pin 活塞环piston pin 活塞梢piston stroke 活塞冲程pitch n. 纵摇plan n. 图纸plane n. 平面plane v. 整平planing machine 校平机plant n. (成套机电)设备platform n. 平台pneumatic tool 气动工具pointing of direction 指向poisonous gas 有毒气体pollution n. 污染poop n. 艉楼port n. 左舷portable light 手提灯postdoctoral centre 博士后工作站potable water 饮用水pour v. 涌入,源源不断power amplifier 功率放大器power plant 动力装置,(火力)电厂power station 电站power supply 电源,供电power system 电力系统,动力系统practice n. 习惯做法preamplifier n. 前置放大器pre-combustion chamber预燃燃烧室pre-heat v. 预热pressure container 压力容器pressure relay 压力继电器pressure sensor 压力传感器pressure tank 压力柜pretreat v. 预处理primary radio transmitter主无线电发信机prime mover 原动机primer n. 底漆primer painting 涂底漆principle dimensions 主尺度process n. 工艺,流程v. 加工,处理production efficiency 生产效率production line 生产线production procedure 生产程序program n. 程序projection plane 投影面prolong v. 延长promote v. 促进,晋升propeller n. 螺旋桨proportion n. 比例propulsion efficiency 推进效力propulsion plant 推进装置protection type 保护式provision n. 食品pump n. 汞purity v. 净化push rod 顶杆push-pull magnetic amplifier推挽磁放大器pyramid method 正装法quality assurance 质量保证quality control 质量控制quality management 质量管理quality policy 质量方针quay n. (顺岸式)码头quiescent a.安静的radar n. 雷达radio beacon station 导航台radio communication equipment无线电通讯设备radio directional finder 无线电测向仪radio message 无线电报radio receive 无线电接收机radio room 报房radio station 电台radio transmitter 无线电发信机radio wave 无线电波range n. 航程range v. 测距range display 航程显示器range unit 航程装置rated power 额定功率rated value 额定值reaction n. 反作用力reading n. 读数receiver n. 接收器reciprocating movement 往复运动rectification n. 矫正,整顿rectify v. 整流,滤波reduction gear 减速齿轮reduction gearbox 减速齿轮箱reduction unit 减速装置reduction with an astern clutch带到车离合器的减速reefer n. (俗)冷藏船,冰箱reflect v. 反射refrigerating plant 制冷装置register n. (机)验船师register vt. 登记,注册regulation n. 登记regulator n. 调整器relative humidity 相对湿度relative motion 相对运动relay contactor 继电器remains n. 残余remote control 遥控remote control station 遥控站rescue v. n. 救援rescue frequency 救援频率rescue transmitter 救援发信机resemble v. 相似reserve buoyancy 储备浮力reservoir n. 容器resistance n. 阻力resistance heat 电热阻rest v. 靠左retaining washer 保护垫片retake v. 回收,取回reversal n. 换向reverse v. 反向逆转reverse power 逆功率reversing system 换向机构revolution n. 旋转rigid a. 刚性的ring seam 环缝rock arm 摇臂roll n. 横摇roller machine 滚床room n. 余地rope n. 缆索rotary movement 旋转运动rotate v. 旋转rotating direction 旋转方向rotation n. 旋转度rotor n. 转子rough sea 波涛汹涌roughness n. 粗糙度routine n. 例行公事rpm 转速rudder n. 舵rudder angle indicator 舵角指示器rudder carrier 舵承,舵托rudder stock 舵轴,舵杆rudder stopper 舵角限制器rules n. 规范,规则running n. 经营管理rust preventative 防锈剂rust prevention 防锈rust removal 除锈rust-proof a.防锈的safeguard v. 捍卫safety valve 安全阀salt content 含盐量sanitary water 卫生水saturated steam 饱和蒸汽scavenge v. n. 扫气scavenge box 扫气箱scavenge flow 扫气气流scavenge pattern 扫气型式screen n. 荧光屏screw shaft 螺旋桨轴sea damage 海损sea trial 试航sea water (SW)海水sea-chart room 海图室seakeeping performances航海性能,试航性seal n. v. 密封sealing agent 密封剂sealing gasket 密封垫片sealing ring 密封圈search light 探照灯seasick a.晕船seat n. 座seating n. 基座section n. 总段self excitation 自励self-designed a.自行设计的self-regulated device 自我调节机构semi-conductor n. 半导体SEMT of France 法国热机协会senior engineer 高级工程师sensibility n. 灵敏度separation n. 分离separator n. 分离器serialize vt.使……成系列service n. 公共基础设施service engineer 服务工程师service life 使用寿命service tank 日用柜servo motor 伺服电动机settle v. 沉淀settling tank 沉淀柜shaft bracket 艉轴架,人字架shaft system 轴系shape processing 成形加工shear machine 剪切机shed v. 放射,散发sheer n. 脊弧sheet plate 薄板shell n. 壳板shell plating 外壳列板shell structure 外板结构ship equipment 船舶结构ship general 总体ship outfitting 船舾ship system 船舶系统shipbuilding n. 造船shipbuilding industry 造船工业shipbuilding technology research institute造船工艺研究所shipping n. 航运shipyard(yard)n. 船厂shop trial 车间实验shore electricity box 岸电箱short circuit 短路short wave 短波short-range a.短途的shot-blast v. 喷丸shot-blasting 喷丸处理side n. 船侧side girderside light 舷灯side plate 弦侧板side structure 船侧结构signal n. 信号signal light 信号灯signal processor 信号处理器silicon n. 硅silicon control rectifier(SCR)可控硅single bottom 单底single-action a.单作用single-rudder n. 单舵single-stage n. 单级single-screw n. 单桨site architect 现场造船师site supervisor 现场监控师sketch n. 草图slide-block n. 滑板,导块sliding distance 滑行距离slipway n. (倾斜)船台slipway taper 船台斜面small metacentric angle 小倾角socialist market economy社会主义市场经济software n. 软件soil n. 土壤SOLAS 国际海上人命安全公约SOS 遇难信号sound energy 声能sound insulation 隔音sound power telephone 声力电话sound speed 声速sound wave 声波sounder n. 测深仪sources of power supply 能源space n. 舱室space n. 空间spare gears 备品spare parts(spares)备件special power supply 特种电源speed indicator 航速指示器speed reduction 减速speed servo system 速度随动系统spring n. 弹簧squeeze n. v. 挤压stability n. 稳性stabilizer n. 减摇鳍stabilizing unit 减摇装置staff member 职员stage n. 级stainless steel 不锈钢stand v. 经受standard n. 标准standard displacement 标准排水量stand-by n. 备用stand-by generating set 备用发电机starboard n. 右舷start v. 动身,出发starting system 起动系统starting valve 启动阀state v. 说明state-specified a.部颁的station v. 驻扎steadiness n. 稳定性steam &aux. boiler system蒸汽与副锅炉系统steel plate pretreatment 钢板预处理steel structure 钢结构steel wire 钢丝steering gear 操舵装置steering gear 舵机steering gear room 舵机房steering mechanism 操舵机构steering wheel 舵轮stem n. 艏柱stern n. 船艉,艉柱stern tube 艉轴管stiffener n. 扶强,加强筋storage tank 贮存柜store-room n. 储藏室straight line 直线straight seam 直焊缝strength test 强度试验stringer n. 纵通材structural material 结构材料structure n. 结构,构件stud n. 螺柱stuffing box 填料函subway shield 地铁盾构suck v. 吸入suction (induction) stroke 汲气冲程suction port 吸入口sufficient a.足够的,充足的sum n. (数)二树之和supercomputer n. 巨型(计算)机superstructure n. 上层建筑supervision n. 监督,监造supply vessel 补给,工作船support n. 支撑物surface treatment 表面处理surveyor n. (船)验船师survive v. 幸存,死里逃生sustain v. 支撑,支持swirl chamber 涡流式燃烧室swirl resistance 涡流式阻力switch n. 开关symbol n. 符号symmetrical a.对称的synchro (selsyn)n. 自整角机synchro signal transmitter 自整角机讯号发送器synchronous device 同步装置synchronous follower 同步随动件talent n. 人才,有才能的technical staff 全体技术人员technical force 技术力量technical service 技术服务technical specification (spec)技术规格书technical term 技术术语telegraph n. 传令钟teleprinter n. 电传打字机teleperature relay 温度继电器temporarily adv. 临时地temporary emergency power supply临时应急电源terminal n. 终端testing n. 调试testing facilities 测试设备testing instrument 测试仪器test & trials 试验与试航TEU reefer container ship 冷风集装箱船the ambient air 大气the application software 应用软件the block coefficient 方型系数the brake horse power (BHP)轴马力,制动马力the breath moulded 型宽the central processing unit (CPU)中央处理单元the centralized control room (the controlroom)集控室the controllable pitch propeller (CPP)可调螺距桨the critical path method (CPM) 各种计划节点配合the data base management system (DBMS)数据库管理系统the depth moulded 型深the design water plane 设计水线面the design water plane coefficient设计水面线系数the displacement coefficient 排水量系数the earth magnetic field 地球磁场the effective horsepower 有效马力the fire main 消防总管the fixed pitch propeller 固定螺距桨the future type 未来型the graphic processing software图像处理软件the intertia navigation system惯性导航系统the integral stud anchor chain 整体锚链the language system 语言系统the length B.P.两柱间长the length overall 全长the length W.L.水线长the living quarters 生活区the longitudinal prismatic coefficient纵向菱形系数the metacentre of transversal inclination 横倾稳心the middle longitudinal cross section舯横剖面the midship transversal cross section coefficient 舯横截面系数the net registered tonnage 净登记吨位the North Pole 北极the office automation (OA)办公自动化the operating system (OS)操作系统the painting outfitting 涂装the parties concerned 有关方面the propulsion plant 推进装置the rated frequency 额定功率the rated horsepower 额定马力the roll period 横摇周期the satellite navigation system卫星导航系统the system software 系统软件the total longitudinal bend 总纵弯曲the total longitudinal strength 总纵强度the total tonnage 总吨位thermal mechanism 热力机械thermal stress 热应力thermometer n. 温度计thread v. 攻螺纹thrust bearing 推力轴承thrust end 推力端thrust ring 推力环thrust shaft 推力轴thyristor n. 硅可控整流器,可控硅tier n. (船)层TIG钨极惰性气体焊tightness test 密性试验time vt. 确定……的时间timing gear 准时机构title n. 职称,头衔tonnage n. 吨位top people 上层人物top side plate 弦侧顶板torsional vibration 扭振torsional moment 扭距TQC全面质量管理transceiver n. 收发报机transfer pump 输送泵transistor amplifier 晶体管放大器transistor controller 晶体控制器transistor loop 晶体管回路transmitter n. 发射机,发送器transportation n. 输送transversal a. 横向的transversal bulkhead 横隔舱壁transversal scavenge 横流扫气transversal stability 横稳性treatment plant 处理装置trend n. 趋势trial-and-error a.反复的通过试验找出错误的trim n. 纵倾trunk-piston n. 筒形活塞T-type joint T型接头tuition n. 学费turbine oil 透平油turbocharger n. 涡轮废气增压器turning ability 回转性turning circle 回转半径turning gear 盘车机构turning motion 回转twenty-foot equivalent unit (TEU)20英尺国际标准集装箱twin-engine incoporation 双机并车twinkle v. 闪烁twin-rudder n. 双舵twin-screw n. 双桨two-way a. 双向的ultra short wave 超短波UMS 无人机舱under voltage 欠电压uneven a. 不均匀uniform a. 均匀的unload v. 卸载upper deck 上甲板upset v. (船只)倾覆vacuum n. 真空validate vt. (使)生效valve mechanism 阀机构vaporize v. 汽化velocity n. 速度ventilating pipe 通风管ventilation &air-conditioning system通风与空调系统ventilator n. 通风机vertical a. 垂直的,直立式的vertical seam 垂直焊缝vertical welding 立焊vibration n. 振动viscosity n. 粘度visible range 视距visual telegraph 灯光传令钟visual-acoustical signal 灯光音响信号voltage n. 电压voltage latching 电压锁定voyage n. 航行waste heat 余热water head 压头water inlet pipe 进水管water jacket 水套water pressure test 水压试验water supply 水源,自来水water supply system 供水系统water vapour 水蒸气waterline 水线watertight a. 水密的water-tight test 水密试验wave impact 波浪冲击力wave-forming (wave-making) resistance兴波阻力wear n. v. 磨损weather post 露天部位weight calculation 重量计算welder n. 焊工,焊机welding n. 焊接welding laboratory(lab)焊接试验室welding machine 焊机welding procedure 焊接方法(工艺)welding seam 焊缝welding wire 焊丝well adv. 完全有理由wheel steering 随从操舵,舵轮操舵wheel house n. 驾驶室whereby adv. 靠那个wing buoyant tank 减摇水舱wire cable 钢索work n. 功working condition 工况working principle 工作原理working schedule 生产进度working site 现场workmanship n. 工艺,流程X-ray photo X光照片yaw n. 偏航角。
ship的用法在英语中,"ship"这个词有很多不同的用法和意义。
下面我们将详细探讨"ship"的几种常见用法。
1. 名词用法:"ship"作为名词时,指的是一艘船舶。
船舶在海上和河流中扮演着重要的角色,用于运输货物和人员。
船舶可以分为各种类型,如货船、客船、战舰等。
例如,"The ship set sail from the harbor."(船从港口起航了)2. 动词用法:"ship"作为及物动词时,有多种含义。
2.1 发货:"ship"可以表示发送或运输货物。
这种用法通常用于商业领域。
例如,"We ship our products worldwide."(我们把产品运往世界各地)2.2 运送人员:"ship"也可以用于表示运送人员。
这种用法常用于军事或其他组织中。
例如,"The military shipped the troops to the battlefield."(军方将部队运送到战场上)2.3 运送道具或装备:"ship"还可以用于表示运输道具、设备或装备。
这种用法常见于电影或表演中。
例如,"The film production company shipped the costumes and props to the filming location."(电影制作公司把服装和道具运到拍摄地点)2.4 发布或发送:"ship"也可以表示发布或发送物品或内容。
这种用法在网络时代尤为常见。
例如,"The company shipped the new software update to all its customers."(公司把新的软件更新发送给所有客户)3. 爱情配对:"ship"在英语中还有一个俚语用法,表示支持或喜欢某两个人作为情侣。
平板龙骨( plate keel )
舭列板(bilge strake)
船底板(bottom plate)
舷顶列板(S列板)(sheer strake)
舷侧列板(side plate)
这些列板在船舶建造中还有专门的术语:K列板称为平板龙骨( plate keel );由船底向舷侧过渡的部位称为毗部,与之相对应的一列板称为舭列板(bilge strake);平板龙骨与砒列板之间的列板统称为船底板(bottom plate);船体舷侧部分在上甲板以下的那一列板称为舷顶列板(S列板)(sheer strake);舭列板以上舷顶列板以下的各列板统称为舷侧列板(side plate ),如图2-t所示。
船壳外板是由许多块钢板焊接而成的,钢板的长边沿船长方向布置。
长边与长边相接叫边接,焊缝称为边接缝( seam );短边与短边相接叫端接,焊缝称为端接缝(Butt)。
甲板板由许多钢板拼合焊接而成,钢板的长边通常沿船长方向布置。
在所有列板中,沿甲板外缘与舷侧邻接的一列板称为甲板边板(deck stringer)。
上甲板边线沿纵向向艏娓端升高的曲线称为舷弧(sheer),见图2一9(a)。
上甲板沿横向这种中间高,两边低的拱形称为梁拱(camber ),见图2-9(b)。
肋板(door)
中内龙骨(keelson) 旁内龙骨(side keelson)舭肘板(bilge bracket) 船底纵骨(bottom longitudinal)防倾肘板(tripping bracket)实肋板(sohdfloor)
减轻孔(Udltellinghole )、气孔(air hale)和流水孔(drain hole) ,有些减轻孔专门设计成便于人员通过的人孔(manhole)。
加强筋(stiffener ) 水密肋板(watertight floor) 水密横舱壁(watertightbulkhead)
组合肋板(bracketfloor)又称框架肋板,由内底横骨(innerbottom frame)、船底肋骨(bottom fraine)和肘板(bracket)组成,见图3-7。
中底桁(centersirder)又称中桁材,是置于船底首尾中心线上的纵向梁,它与平板龙骨( flatplatekeel)、中内底板(centerinnerbottomplating)组成工字型纵向构件。
旁底桁(sidesirder)又称边底桁,对称设置于中桁材两侧且平行于中桁材,并与船底板和内底板相连,其上开有减轻孔、流水孔、人孔和气孔等,一船间断于实肋板之间。
箱形中底桁(ductkeel)又称箱形龙骨,它是由两道水密的侧板(底纵桁)、内底板、船底板和骨材等组成的水密箱形结构,如图3-10所示。
船底纵骨(bottom longitudinal) 内底纵骨(innerhottom longitudinal)
分节驳(integrated barge)
肋骨(frame ) 甲板间肋骨(tweendeck frame ) 中间肋骨(intermediate frame)强肋骨(web frame)舷侧纵析(side stringer) 舷侧纵骨(side longitudinal)
化学品液货船( liquid chemical tanker)
舷侧纵舱壁和舷侧外板围成的舷边舱( wing tank)可用作压载水舱(ballast water tank )
上层平台与上甲板的箱形结构称做抗扭箱( torsion box )
甲板结构由甲板板和甲板骨架(deck framing)组成。
横梁(beam)
普遍横梁( deck beam ) 普通横梁是横骨架式甲板结构中的主要构件,常用不等边角钢制成,也有用球扁钢的。
它的两端用梁肘板(beam knee)与舷侧主肋骨连接,梁肘板的高度不小于肋骨腹板高度的2倍。
普通横梁与甲板纵桁相遇时,纵桁腹板上开切口横梁穿过,并且每隔2~4档肋距设置防倾肘板,如图5-2(a)所示。
半梁(half beam) 强横梁(web beam)舱口端横梁(hatch end beam)
甲板纵桁(deck girder)
沿舱口边的纵桁称为舱口纵桁(hatch side girder)。
肘板〔knee)横骨架式甲板结构中有许多处肘板,有连接横梁与肋骨的梁肘板(beam knee)、连接横梁与甲板纵桁的防倾肘板。
舷伸甲板(sponson deck)
货舱口(cargo hatch)和货舱围板(hatch coaming)
支柱(pillar)是船舱内的竖直构件,由钢管或工字钢等做成。
货油舱不须开大舱口,为了清舱,仅开设人员出人舱口(excess hatch ),兼作膨胀井( expansian trunk)。
顶边舱( topside tank)船上有许多横向和纵向布置的舱壁(hulkhead ) ,沿纵向设置的舱壁是纵舱壁( longitudinal bulkhead),沿横向设置的舱壁是横舱壁(transverse bulkhead ) 。
水密舱壁(watertight buikhead)局部舱壁(partial bulkhead)艉尖舱舱壁(afterpeak bulkhead)尾轴管(shaft tube)舵杆围阱(rudder trunk)
隔离空舱(cofferdam)
中纵舱壁(centerline bulkhead)
平面舱壁(plane bulkhead)由舱壁板和骨架组成。
垂直、水平扶强材(vertical、horizontal stiffener)
槽型舱壁(corrugated bulkhead)
压筋板(swaged plate)
艏部形状见图7一1所示,其中图(a)为直立型艏(vertical bow ),艏柱呈直线型,与基线相垂直或接近垂直。
现代船舶除了一些驳船和特种船舶外已很少采用。
图(b)为前倾型艏( raked bow ) , 艏柱向前倾斜,呈直线或微带曲线,这种形式的舷部不易上浪,在发生碰撞时船体水线以下的部分不易受损,外观上具有快速感。
直线前倾型在军舰上用得较多,民船上常用微带曲线前倾型。
图(c)为飞剪型艏(clipper bow),又称伸长甲板式船舶,设计水线以上呈凹形曲线,具有较大的甲板悬伸部。
这种形式除了不易上浪外,悬伸部较大的甲板面积有利于锚机和系泊设备的布置。
图( d )为破冰型艏(jcehreaker bow ),设计水线以下的艏柱呈倾斜状,与基线约成30度夹角。
这种形式用在破冰船上。
图(e)为球鼻型( bulb bow ),设计水线以下的艏部前端有球鼻型的突出体,可以降低船舶的兴波阻力。
这种形式的艏部广泛用在大型远洋货船上,军舰上可以利用球鼻的突出体装置声呐设备。
椭圆型艇(elliptical stern)巡洋舰艉( cruiser stem ) 方形艉(transom stern)
艏尖舱(fore peak)防撞舱壁(collision bulkhead)升高肋板(raised floor)强胸横梁(panting beam)制荡舱壁(wash bulkhead)
斜肋骨(cant frame)和斜横梁(cant beam)
艏肘板(breasthook)
艏端侧推器管隧就是在艏部横向贯通的管隧(tunnel ),其内装有电动机驱动的侧向推进器。
侧推器(thruster)在船舶靠近码头和改变航向时,作为辅助的推进器特别有效。
艉柱(stern frame)舵柱(rudder post)螺旋桨柱(propeller post)艉柱底骨(shoe piece)
双臂艉轴架有两个支臂,俗称人字架(A-bracket)。
轴包套(shell bossing)
上甲板以下的部分通常称为船舶的主体;位于上甲板以上的各种围蔽建筑则统称为上层建筑(superstructure)。
上层建筑分为船楼和甲板(deck house)两种类型。
船楼的两个侧壁伸至船的两舷或距舷边的距离小于船宽的3% , 船楼根据所在的位置分为艏楼(forecastle )、桥楼(bridge)、艉楼(poop),见图8-1。
机舱棚(engine casing)
76页。