aoc65t12s说明书

Q27G3S安全 (1)标志惯例 (1)电源 (2)安装 (3)清洁 (4)其它 (5)设置 (6)物品清单 (6)安装支架和底座 (7)调整视角 (8)连接显示器 (9)Adaptive-Sync功能 (10)HDR (11)调节显示器 (12)热键 (12)OSD设定 (13)Luminance（明亮度） (14)Color Setup（颜色设置） (15)Picture Boost（窗口增亮） (16)OSD Setup（OSD设置） (17)Game Setting（游戏设置） (18)Extra（其它） (20)Exit（退出） (21)LED指示灯 (22)故障排除 (23)规格 (24)主要规格 (24)预设显示模式 (25)引脚分配 (26)即插即用 (27)安全标志惯例以下小节描述此文档中使用的标志惯例。

注释、注意和警告在本指南中，文本块可能带有图标并且以粗体或斜体打印。

这些文本块是注释、注意和警告，如下所示：注释：注意事项指示帮助你更好地使用你的计算机系统的重要信息。

注意：“注意”表示潜在的硬件损坏或数据丢失，并告诉您如何避免出现问题。

警告：“警告”表示存在潜在的人身伤害，并告诉您如何避免伤害的发生。

某些警告可能采用其它格式，也可能不带有图标。

在这种情况下，由相关的管制机构提供专门的警告表示方法。

显示器应使用铭牌上标示的电源规格。

如果您不能确定家里电源规格，请咨询供应商或当地电力公司。

显示器配备三项接地插头，一个插头具有第三个（接地）引脚。

这个引脚会只嵌入作为安全装置的接地电源插座。

如果插座不适合三线插头，那么请让电工安装正确的插座，或者使用转接器使得仪器安全接地。

请不要使接地插头的安全目的失效。

在雷雨天气或者当长期不用时请拔掉电源插头。

这可以保护显示器不会因为电压剧烈变化而遭到损坏。

请勿使电源插座和外接电源线过载。

过载可能会导致电击和火灾。

为了确保正确安全的操作，仅可将显示器与通过UL 认证的计算机配合使用，这些计算机的电源插座采用标准配置，电压标为交流 100-240V 之间、最小电流为 5A 。

©2020 AOC. All Rights Reserved.LCD MonitorUser ManualQ32V3SSafety (1)National Conventions (1)Power (2)Installation (3)Cleaning (4)Other (5)Setup (6)Contents in Box (6)Setup Stand & Base (7)Adjusting Viewing Angle (8)Connecting the Monitor (9)Adjusting (10)Hotkeys (10)OSD Setting (12)Luminance (13)Color Setup (14)Picture Boost (15)OSD Setup (16)Game Setting (17)Extra (18)Exit (19)LED Indicator (20)Troubleshoot (21)Specification (22)General Specification (22)Preset Display Modes (23)Pin Assignments (24)Plug and Play (25)SafetyNational ConventionsThe following subsections describe notational conventions used in this document.Notes, Cautions, and WarningsThroughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:NOTE: A NOTE indicates important information that helps you make better use of your computer system.CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.PowerThe monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fitonly into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.Do not overload power strips and extension cords. Overloading can result in fire or electric shock.To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 1.5A.The wall socket shall be installed near the equipment and shall be easily accessible.InstallationDo not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electricshock. Never spill liquids on the monitor. Do not place the front of the product on the floor.If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tiltdownward by more than -5 degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty.Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate henceoverheating may cause a fire or damage to the monitor.See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:Installed with stand Installed with standPlease purchase a suitable wall mount to avoid the lack of distance between the back signal cable and the wall.CleaningClean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.Please disconnect the power cord before cleaning the product.OtherIf the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.Make sure that the ventilating openings are not blocked by a table or curtain.Do not engage the LCD monitor in severe vibration or high impact conditions during operation.Do not knock or drop the monitor during operation or transportation.SetupContents in Box**Not all signal cables (DP , HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.CD Manual Warranty card Base Power Cable HDMI Cable DP CableSetup Stand & BasePlease setup or remove the base following the steps as below. Setup:Remove:Adjusting Viewing AngleFor optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference.Hold the stand so you will not topple the monitor when you change the monitor’s angle.You are able to adjust the monitor as below:NOTE:Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.* Display design may differ from those illustrated.Warning• To avoid potential screen damage, such as panel peeling, ensure that the monitor does no t tilt downward by more than -5 degrees.• Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.Connecting the MonitorCable Connections In Back of Monitor and Computer:1. Power2. Earphone3. DisplayPort4. HDMIConnect to PC1. Connect the power cord to the back of the display firmly.2. Turn off your computer and unplug its power cable.3. Connect the display signal cable to the video connector on the back of your computer.4. Plug the power cord of your computer and your display into a nearby outlet.5. Turn on your computer and display.If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting. To protect equipment, always turn off the PC and LCD monitor before connecting.AdjustingHotkeys1Source/Exit/Up2Eco/DCR/Down3Clear Vision/Left4Volume/Right5Power/ Menu/EnterMenu/EnterWhen there is no OSD, Press to display the OSD or confirm the selection. Press about 2 second to turn off the monitor.PowerPress the Power button to turn on the monitor.Volume/RightWhen there is no OSD, Press Volume button to active volume adjustment bar, Press Left or Right to adjust volume.Source/ExitWhen the OSD is closed, press Source/Exit button will be Source hot key function.Eco /DCR/DownWhen there is no OSD, Press this button to enter Eco/DCR adjustment. Then press Left or Right button to choose different Eco/DCR.Clear Vision1. When there is no OSD, Press the “Left” button to activate Clear Vision.2. Use the “Left” or “Right” buttons to select between weak, medium, strong, or off settings. Default setting is always “off”.3. Press and hold “Left” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo:on” will be display on the screen for a duration of 5 seconds. Press and hold “Left” button for 5 seconds again, Clear Vision Demo will be off.Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.Clear VisionOffAdjust the Clear VisionWeak Medium StrongClear Vision DemoOn or OffDisable or Enable DemoOSD SettingBasic and simple instruction on the control keys.OSD Setup1). Press the MENU-button to activate the OSD window.2). Press Left or Right to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it, press Left or Right to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.3). Press Left or Right to change the settings of the selected function. Press Exit–button to exit. If you want to adjustany other function, repeat steps 2-3.4). OSD Lock/Unlock Function: To lock or unlock the OSD, press and hold the Down–button for 10s while OSD functionis not active.Notes:1). If the product has only one signal input, the item of “Input Select” is disable to adjust.2). ECO modes (except Standard mode), Clear vision, DCR, DCB mode and Picture Boost, for these states that only onestate can exist.LuminanceOSD SetupContrast 0-100 Contrast from Digital-register.Brightness 0-100 Backlight Adjustment.Eco modeStandard Standard Mode.Text Text Mode.Internet Internet Mode.Game Game Mode.Movie Movie Mode.Sports Sports Mode.Reading Reading Mode.GammaGamma1Adjust to Gamma 1.Gamma2Adjust to Gamma 2.Gamma3Adjust to Gamma 3.DCROn Enable dynamic contrast ratio.Off Disable dynamic contrast ratio.HDR ModeOffSelect HDR Mode.HDR PictureHDR MovieHDR GameNote:When “HDR Mode” is set to “non-off”, the items “Contrast”, “Brightness”, “Gamma” cannot be adjusted.Color SetupOSD SetupColor Temp.Warm Recall Warm Color Temperature from EEPROM.Normal Recall Normal Color Temperature from EEPROM.Cool Recall Cool Color Temperature from EEPROM.sRGB Recall SRGB Color Temperature from EEPROM.User Restore Color Temperature from EEPROM.DCB ModeFull Enhance On or Off Disable or Enable Full Enhance ModeNature Skin On or Off Disable or Enable Nature Skin ModeGreen Field On or Off Disable or Enable Green Field ModeSky-blue On or Off Disable or Enable Sky-blue ModeAutoDetect On or Off Disable or Enable AutoDetect ModeOff On or Off Disable or Enable Off ModeDCB Demo On or Off Disable or Enable DemoRed0-100Red gain from Digital-register.Green0-100Green gain from Digital-register.Blue0-100Blue gain from Digital-register.Note:When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Color Setup” cannot be adjusted.Picture BoostOSD SetupBright Frame on or off Disable or Enable Bright FrameFrame Size 14-100 Adjust Frame SizeBrightness 0-100 Adjust Frame BrightnessContrast 0-100 Adjust Frame ContrastH. position 0-100 Adjust Frame horizontal PositionV. position0-100 Adjust Frame vertical PositionNote:Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Picture Boost” cannot be adjusted.OSD SetupOSD Setup Language Select the OSD language Timeout5-120Adjust the OSD TimeoutDP Capability(only for certain models) 1.1/1.2If the DP video content supports DP1.2, please select DP1.2 for DP Capability; otherwise, please select DP1.1.Please be noted that only DP1.2 support Adaptive-Sync functionH. Position 0-100 Adjust the horizontal position of OSD V. Position 0-100 Adjust the vertical position of OSD Transparence 0-100Adjust the transparence of OSDBreak Reminderon or offBreak reminder if the user continuously work for more than 1hrsGame SettingOSD SetupGame ModeOff No optimization by Smart image gameFPSFor playing FPS (first Person Shooters) games.Improves dark theme black level details.RTSFor playing RTS (Real Time Strategy). Improves theimage quality.RacingFor playing Racing games, Provides fastest responsetime and high color saturation.Gamer 1User’s preference settings saved as Gamer 1.Gamer 2User’s preference settings saved as Gamer 2.Gamer 3User’s preference settings saved as Gamer 3.Shadow Control0-100Shadow Control Default is 50, then end-user can adjustfrom 50 to 100 or 0 to increase contrast for clear picture.1. If picture is too dark to be saw the detail clearly,adjusting from 50 to100 for clear picture.2. If picture is too white to be saw the detail clearly,adjusting from 50 to0 for clear pictureOverdrive(only for certainmodels)OffAdjust the response time.WeakMediumStrongGame Color0-20Game Color will provide 0-20 level for adjustingsaturation to get better picture.LowBlue ModeReading / Office /Internet / Multimedia /OffDecrease blue light wave by controlling colortemperature.Dial Point On or OffThe “Dial Point” function places an aiming indicator inthecenter of screen for helping gamers to play First PersonShooter (FPS) games with an accurate and preciseaiming.Adaptive-Sync(only for certainmodels)On or OffDisable or Enable Adaptive-Sync.Adaptive-Sync Run Reminder: When the Adaptive-Syncfeature is enabled, there may be flashing in some gameenvironments.Frame Counter(only for certainmodels)Off / Right-up / Right-Down / Left-Down /Left-UpDisplay V frequency on the corner selectedNote:When “HDR Mode” under “Luminance” is set to “non-off”, the items “Game Mode”, “Shadow Control”, “Game Color” cannot be adjusted.ExtraOSD SetupInput Select Select Input Signal SourceOff timer0-24hrs Select DC off timeImage RatioWideSelect image ratio for display.4:3DDC/CI Yes or No Turn ON/OFF DDC/CI SupportResetYes or No Reset the menu to default(ENERGY STAR® available for selective models) ENERGY STAR® or NoExitOSD SetupExit Exit the main OSDLED IndicatorStatus LED Color Full Power Mode White Active-off Mode OrangeTroubleshootProblem & Question Possible SolutionsPower LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to agrounded power outlet and to the monitor.No images on the screen Is the power cord connected properly?Check the power cord connection and power supply.Is the cable connected correctly?(Connected using the HDMI cable)Check the HDMI cable connection.(Connected using the DP cable)Check the DP cable connection.* HDMI/DP input is not available on every model.If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card.(Refer to the Setting the Optimal Resolution)If the initial screen (the login screen) does not appear, contact the ServiceCenter or your dealer.Can you see “Input Not Supported” on the screen?You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly.Make sure the AOC Monitor Drivers are installed.Picture Is Fuzzy & Has Ghosting Shadowing Problem Adjust the Contrast and Brightness Controls.Press to auto adjust.Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back.Picture Bounces, Flickers Or Wave Pattern Appears In The Picture Move electrical devices that may cause electrical interference as far away from the monitor as possible.Use the maximum refresh rate your monitor is capable of at the resolution you are using.Monitor Is Stuck In Active Off-Mode”The Computer Power Switch should be in the ON position.The Computer Video Card should be snugly fitted in its slot.Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent.Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.Missing one of the primary colors (RED, GREEN, or BLUE)Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.Picture has color defects(white does not look white)Adjust RGB color or select desired color temperature.Horizontal or vertical disturbances on the screen Use Windows 7/8/10 shut-down mode to adjust CLOCK and FOCUS. Press to auto-adjust.Regulation & Service Please refer to Regulation & Service Information which is in the CD manual or (to find the model you purchase in your country and to find Regulation & Service Information in Support page.Specification General SpecificationPanel Model name Q32V3SDriving system TFT Color LCDViewable Image Size80.2 cm diagonalPixel pitch 0.272mm(H) x 0.272mm(V) Video HDMI lnterface & DP Interface Display Color 16.7M ColorsOthers Horizontal scan range 30k-114kHzHorizontal scan Size(Maximum)698.112mmVertical scan range 48-75HzVertical Scan Size(Maximum)392.688mmOptimal preset resolution 2560x1440@60HzMax resolution2560x1440@75HzPlug & Play VESA DDC2B/CIInput Connector HDMI/DPPower Source 100-240V~, 50/60Hz,1.5APower ConsumptionTypical (default brightness and contrast)47WMax. (brightness = 100, contrast =100)≤52WStandby mode≤0.3WPhysical Characteristics Connector Type HDMI/DP/Earphone out Signal Cable Type DetachableEnvironmental TemperatureOperating 0°~ 40°Non-Operating -25°~ 55°HumidityOperating 10% ~ 85% (non-condensing)Non-Operating 5% ~ 93% (non-condensing) AltitudeOperating 0~ 5000 m (0~ 16404ft )Non-Operating 0~ 12192m (0~ 40000ft )Preset Display ModesSTANDARD RESOLUTION HORIZONTALFREQUENCY(kHz)VERTICAL FREQUENCY(Hz)VGA640x480@60Hz31,46959,94 VGA640x480@67Hz3566,667 VGA640x480@72Hz37,86172,809 VGA640x480@75Hz37,575 DOS MODE720x400@70Hz31,46970,087 DOS MODE720x480@60Hz29,85559,710 SD720x576@50Hz31,2550 SVGA800x600@56Hz35,15656,25 SVGA800x600@60Hz37,87960,317 SVGA800x600@72Hz48,07772,188 SVGA800x600@75Hz46,87575 SVGA832x624@75Hz49,72574,551 XGA1024x768@60Hz48,36360,004 XGA1024x768@70Hz56,47670,069 XGA1024x768@75Hz60,02375,029 XGA1024x768@75Hz60,24174,927 SXGA1280x1024@60Hz63,98160,02 SXGA1280x1024@75Hz79,97575,025 Full HD1920x1080@60Hz67,560 QHD2560x1440@60Hz88,78759,951 QHD2560x1440@75Hz111,02874,968Pin AssignmentsPin No.Signal Name Pin No.Signal Name Pin No.Signal Name1.TMDS Data 2+9.TMDS Data 0-17.DDC/CEC Ground2.TMDS Data 2 Shield10.TMDS Clock +18.+5V Power3.TMDS Data 2-11.TMDS Clock Shield19.Hot Plug Detect4.TMDS Data 1+12.TMDS Clock-5.TMDS Data 1Shield13.CEC6.TMDS Data 1-14.Reserved (N.C. on device)7.TMDS Data 0+15.SCL8.TMDS Data 0 Shield16.SDA20-Pin Color Display Signal CablePin No.Signal Name Pin No.Signal Name 1ML_Lane 3 (n)11GND2GND12ML_Lane 0 (p)3ML_Lane 3 (p)13CONFIG14ML_Lane 2 (n)14CONFIG25GND15AUX_CH(p)6ML_Lane 2 (p)16GND7ML_Lane 1 (n)17AUX_CH(n)8GND18Hot Plug Detect9ML_Lane 1 (p)19Return DP_PWR10ML_Lane 0 (n)20DP_PWRPlug and PlayPlug & Play DDC2B FeatureThis monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.。

65" Series 9Q900R 8K QLED TV Depth and detail in 8K Resolution.* Native 8K content availability is very limited. Picture quality of upscaled content will vary depending on the quality and resolution of source content.^ Compared to Samsung QLED Q90R TV and lower.TopFeatures8K ResolutionA new generation in technology now let's youexperience our best expression of depth and clarity in big screen TV entertainment like never before.*8K AI UpscalingQLED 8K AI Upscaling uses the power of machine learning to analyse and upscale your favouritecontent to 8K resolution, so you get the most out of your big screen TV despite the limited availability of native 8K content.*Ultra Bright IIIOur best expression of brightness and contrast let's you discover deeper, more intense colours so you get an incredible viewing experience, even in sun filled rooms.^Product Product Category8K QLED TVModel Number QA65Q900RBWXXYDisplay Screen Size (rounded)Inch65Screen Size (rounded)cm163Display Technology QLED 8KResolution7680 x 4320 (8K UHD)Motion Refresh Rate Hz200Picture Quality Colour Quantum DotContrast Direct Full Array Elite IIIAnti Reflection Screen YesBacklight Full Array (Direct)Local Dimming YesHigh Dynamic Range Yes (Ultra Bright III)HLG(Hybrid Log Gamma)YesMicro Dimming Ultimate 8K DimmingSpecialised Game Mode Yes(4)Auto Game Mode Yes (14 ms input lag)Dynamic Black Equalizer YesVariable Refresh Rate YesPicture Modes Dynamic,Standard, Natural, MoviePicture Engine Quantum Processor 8KProcessor Quad-CoreStyle Bezel 4 Bezel-lessStand Type SimpleStand Colour BlackOne Connect Box YesCable Management YesSlim Fit Wall-Mount Compatible YesVESA Wall Mount Support mm400 x 400VESA Standard Screw Size M8VESA Standard Screw Depth19-21Optional Stand Compatible NoSmart Smart TV YesOperating System TizenFreeview+YesOne Remote Control YesSmartThings TV App YesSmartThings Mobile App Yes (Android 6.0↑ and iPhone 6 iOS 10.0↑)Web Browser YesBixby YesWorks WithYesGoogle Assistant/Amazon Alexa/AirPlay 2Connectivity HDMI inputs4USB3Component In (Y/Pb/Pr)1Composite In (AV) 1 (Common Use for Component Y)Ethernet (LAN)YesDigital Audio Out (Optical)1RF In(Terrestrial / Cable input / Satellite input)1/1(Common Use for Terrestrial)/0HDMI Audio Return Ch. (ARC) Support YesHDMI Quick Switch YesWireless LAN Built-in Yes (2.4GHz only –802.11n)Anynet+ (HDMI-CEC)YesAuto Device Detection YesConvergence TV to Mobile -Mirroring YesMobile to TV –Mirroring, DLNA Yes (Android 6.0↑ with Screen Cast capabilities)360 Video Player Yes360 Camera Support YesBluetooth Low Energy YesWi-Fi Direct YesTV Sound to Mobile YesTuner/Digital Broadcasting DVB-T (T2Ready)Broadcasting Analog Tuner YesData Broadcasting HbbTV1.5Power Power Consumption (Max)W370Power Consumption(Standby)W0.5Power Consumption (Typical)W308Eco Sensor YesAudio Dolby Digital Plus YesSound Output60WSpeaker Type 4.2 CHWoofer YesBluetooth Audio YesMulti Output Audio YesAdditional Features AI Technology YesIntelligent Mode YesAccessibility Voice guide & Learn menu screen (AU English)/ Enlarge/High contrast/ Learn TV Remote(AU English)/ Negativecolours/ Grayscale/ SeeColoursAuto Channel Search YesAuto Power Off YesSubtitles YesConnectShare™ (HDD)YesConnectShare™ (USB 2.0)YesElectronic Program Guide YesPersonal Video Recording YesTeletext (TTX)YesTime Shift YesAccessories Remote Control Yes (TM1990C)(Included)Batteries for Remote Control YesPower Cable m 1.5User Manual YesE-Manual YesDimensions TV with stand (W x H x D)mm1452.2 x 898.2 x 304.9TV without stand (W x H x D)mm1452.2 x 836.4 x 34.1Package (W x H x D)mm1621 x 980 x 195Weight TV with stand kg31.2TV without stand kg30.2Package kg43.1EAN8801643751296Warranty12 Months。

LCD Monitor User Manual 24T1Q/27T1Q/Q27T1LED backlightSafety (1)National Conventions (1)Power (2)Installation (3)Cleaning (4)Other (5)Setup (6)Contents in Box (6)Adjusting Viewing Angle (7)Connecting the Monitor (8)Adaptive-Sync function (9)Adjusting (10)Hotkeys (10)OSD Setting (12)Luminance (13)Color Setup (14)Picture Boost (15)OSD Setup (16)Extra (17)Exit (18)LED Indicator (19)Driver (20)i-Menu (Screen+) (20)e-Saver (21)Troubleshoot (22)Specification (23)General Specification (23)Preset Display Modes (26)Pin Assignments (28)Plug and Play (29)SafetyNational ConventionsThe following subsections describe notational conventions used in this document.Notes, Cautions, and WarningsThroughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:NOTE: A NOTE indicates important information that helps you make better use of your computer system.CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.PowerThe monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fitonly into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.Do not overload power strips and extension cords. Overloading can result in fire or electric shock.To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 5A.The wall socket shall be installed near the equipment and shall be easily accessible.For use only with the attached power adapterManufacturer: L&T Display Technology(Fujian) Ltd Model: STK025-19131T (24T1Q, 27T1Q)Manufacturer: TPV Electronics (Fujian) Co., Ltd. Model: ADPC1945 (Q27T1)InstallationDo not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electricshock. Never spill liquids on the monitor. Do not place the front of the product on the floor.If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate henceoverheating may cause a fire or damage to the monitor.See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:Installed with stand Installed with standPlease purchase a suitable wall mount to avoid the lack of distance between the back signal cable and the wall.CleaningClean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.Please disconnect the power cord before cleaning the product.OtherIf the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.Make sure that the ventilating openings are not blocked by a table or curtain.Do not engage the LCD monitor in severe vibration or high impact conditions during operation.Do not knock or drop the monitor during operation or transportation.SetupContents in Box***Not all signal cables (DP , HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.CD Manual Warranty card Power Cable Adapter HDMI Cable DP CableDo not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.Connecting the MonitorCable Connections In Back of Monitor and Computer:1. Power2. Earphone3. DisplayPort4. HDMIConnect to PC1. Connect the power cord to the back of the display firmly.2. Turn off your computer and unplug its power cable.3. Connect the display signal cable to the video connector on the back of your computer.4. Plug the power cord of your computer and your display into a nearby outlet.5. Turn on your computer and display.If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting. To protect equipment, always turn off the PC and LCD monitor before connecting.Adaptive-Sync function1. Adaptive-Sync function is working with DP/HDMI2. Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting • Radeon™ RX Vega series• Radeon™ RX 500 series• Radeon™ RX 400 series• Radeon™ R9/R7 300 series （R9 370/X, R7 370/X, R7 265except）• Radeon™ Pro Duo (2016)• Radeon™ R9 Nano series• Radeon™ R9 Fury series• Radeon™ R9/R7 200 series (R9 270/X, R9 280/X except)AdjustingHotkeys123451Source/Exit2Clear Vision/Left3Volume/Right4Menu/Enter5PowerMenu/EnterPress to display the OSD or confirm the selection.PowerPress the Power button to turn on the monitor.Volume/RightWhen there is no OSD, Press Volume button to active volume adjustment bar, Press Left or Right to adjust volume.Source/ExitWhen the OSD is closed, press Source/Exit button will be Source hot key function.Clear Vision1. When there is no OSD, Press the “Left” button to activate Clear Vision.2. Use the “Left” or “Right” buttons to select between weak, medium, strong, or off settings. Default setting is always“off”.3. Press and hold “Left” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo:on” will be display on the screen for a duration of 5 seconds. Press and hold “Left” button for 5 seconds again, Clear Vision Demo will be off.Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.Clear VisionOffAdjust the Clear VisionWeak Medium StrongClear Vision DemoOn or OffDisable or Enable DemoOSD SettingBasic and simple instruction on the control keys.OSD Setup1). Press the MENU-button to activate the OSD window.2). Press Left or Right to navigate through the functions. Once the desired function is highlighted, press theMENU-button to activate it, press Left or Right to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.3). Press Left or to change the settings of the selected function. Press to exit. If you want to adjust any otherfunction, repeat steps 2-3.4). OSD Lock Function: To lock the OSD, press and hold the MENU-button while the monitor is off and then presspower button to turn the monitor on. To un-lock the OSD - press and hold the MENU-button while the monitor is off and then press power button to turn the monitor on.Notes:1). If the product has only one signal input, the item of “Input Select” is disable to adjust.2). Clear vision, DCR, Color Boost and Picture Boost, for these states that only one state can exist.LuminanceOSD SetupContrast 0-100 Contrast from Digital-register.Brightness 0-100 Backlight AdjustmentEco modeStandard Standard ModeText Text ModeInternet Internet ModeGame Game ModeMovie Movie ModeSports Sports ModeReading Reading ModeGammaGamma1Adjust to Gamma 1Gamma2Adjust to Gamma 2Gamma3Adjust to Gamma 3DCROff Disable dynamic contrast ratioOn Enable dynamic contrast ratioOverdriveWeakAdjust the response time.MediumStrongBoost (Q27T1)OffMBR (Q27T1)0 ~ 20Adjust the Motion Blur Reduction.Note:The function MBR and Overdrive Boost are available only when Adaptive-Sync is off and the vertical frequency is up to 75 Hz.Color SetupOSD SetupColor Temp.Warm Recall Warm Color Temperature from EEPROM.Normal Recall Normal Color Temperature from EEPROM.Cool Recall Cool Color Temperature from EEPROM.sRGB Recall SRGB Color Temperature from EEPROM.User Restore Color Temperature from EEPROM. DCB ModeFull Enhance On or Off Disable or Enable Full Enhance ModeNature Skin On or Off Disable or Enable Nature Skin ModeGreen Field On or Off Disable or Enable Green Field ModeSky-blue On or Off Disable or Enable Sky-blue ModeAutoDetect On or Off Disable or Enable AutoDetect ModeDCB Demo On or Off Disable or Enable DemoRed0-100Red gain from Digital-register.Green0-100Green gain from Digital-register.Blue0-100Blue gain from Digital-register.LowBlueModeMultimediaDecrease blue light wave by controlling colortemperatureInternetOfficeReadingOffPicture BoostOSD SetupBright Frame on or off Disable or Enable Bright FrameFrame Size 14-100 Adjust Frame SizeBrightness 0-100 Adjust Frame BrightnessContrast 0-100 Adjust Frame ContrastH. position 0-100 Adjust Frame horizontal PositionV. position0-100 Adjust Frame vertical PositionNote:Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.OSD SetupOSD Setup Language Select the OSD language Timeout 5-120Adjust the OSD TimeoutDP Capability 1.1/1.2Please be noted that only DP1.2 support Adaptive-Sync functionH. Position 0-100 Adjust the horizontal position of OSD V. Position 0-100 Adjust the vertical position of OSD Adaptive-Sync on or off Disable or Enable Adaptive-Sync.Transparence 0-100Adjust the transparence of OSDBreak ReminderOn or OffBreak reminder if the user continuously work for more than 1hrsNotes:If the DP video content supports DP1.2, please select DP1.2 for DP Capability; otherwise, please select DP1.1.OSD SetupInput Select Select Input Signal SourceAuto Config. Yes or No Auto adjust the picture to default Off timer0-24hrs Select DC off timeImage Ratio 24T1Q/27T1Q: Wide/4:3Q27T1: Wide / 4:3 / 1:1 / Movie1 / Movie2Select image ratio for display.DDC/CI Yes or No Turn ON/OFF DDC/CI Support Reset Yes or No Reset the menu to defaultOSD SetupExit Exit the main OSDLED IndicatorStatus LED Color Full Power Mode White Active-off Mode OrangeDriveri-Menu (Screen+)Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide. The software Supported operating systems: Windows 10, Windows 8, Windows 7.Screen+ can be turned on via i-Menu. It is a desktop screen splitting tool, it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier.e-SaverWelcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).Please click on “driver/e-Saver/setup.exe” to start installing the e-Saver software, follow the install wizard to complete software installation.Under each of the four PC status, you may choose from the pull-down menu the desired time (in minutes) you’re your monitor to automatically shut down. The example above illustrated:The monitor will never shutdown when the PC is powered on.The monitor will automatically shutdown 5 minutes after the PC is powered off.The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.The monitor will automatically shutdown 20 minutes after the screen saver appears.You can click “RESET” to set the e-Saver to its default settings like below.TroubleshootProblem & Question Possible SolutionsPower LED Is Not ON Make sure the power button is ON and the Power Cord is properlyconnected to a grounded power outlet and to the monitor.No images on the screen Is the power cord connected properly?Check the power cord connection and power supply.Is the cable connected correctly?(Connected using the HDMI cable)Check the HDMI cable connection.(Connected using the DP cable)Check the DP cable connection.* HDMI/DP input is not available on every model.If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card.(Refer to the Setting the Optimal Resolution)If the initial screen (the login screen) does not appear, contact the ServiceCenter or your dealer.Can you see “Input Not Supported” on the screen?You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.Adjust the maximum resolution and frequency that the monitor can handle properly.Make sure the AOC Monitor Drivers are installed.Picture Is Fuzzy & Has Ghosting Shadowing Problem Adjust the Contrast and Brightness Controls.Press to auto adjust.Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back.Picture Bounces, Flickers Or Wave Pattern Appears In The Picture Move electrical devices that may cause electrical interference as far away from the monitor as possible.Use the maximum refresh rate your monitor is capable of at the resolution you are using.Monitor Is Stuck In Active Off-Mode”The Computer Power Switch should be in the ON position.The Computer Video Card should be snugly fitted in its slot.Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent.Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.Missing one of the primary colors (RED, GREEN, or BLUE)Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.Picture has color defects(white does not look white)Adjust RGB color or select desired color temperature.Horizontal or vertical disturbances on the screen Use Windows 7/8/10 shut-down mode to adjust CLOCK and FOCUS. Press to auto-adjust.Specification General SpecificationPanel Model name24T1QDriving system TFT Color LCDViewable Image Size60.47 cm diagonalPixel pitch 0.2745mm(H) x 0.2745mm(V) Video HDMI lnterface & DP Interface Display Color 16.7M ColorsOthers Horizontal scan range 30k-85kHzHorizontal scan Size(Maximum)527.04mmVertical scan range 48-75HzVertical Scan Size(Maximum)296.46mmOptimal preset resolution 1920x1080@60HzMax resolution1920x1080@75HzPlug & Play VESA DDC2B/CIInput Connector HDMI/DPPower Source 19Vdc, 1.31APower ConsumptionTypical (default brightness and contrast)21WMax. (brightness = 100, contrast =100)26WPower saving≤0.3WPhysical Characteristics Connector Type HDMI/DP/Earphone out Signal Cable Type DetachableEnvironmental TemperatureOperating 0°~ 40°Non-Operating -25°~ 55°HumidityOperating 10% ~ 85% (non-condensing)Non-Operating 5% ~ 93% (non-condensing) AltitudeOperating 0~ 5000 m (0~ 16404ft )Non-Operating 0~ 12192m (0~ 40000ft )Panel Viewable Image Size68.6 cm diagonalPixel pitch 0.3114mm(H) x 0.3114mm(V) Video HDMI lnterface & DP Interface Display Color 16.7M ColorsOthers Horizontal scan range 30k-85kHzHorizontal scan Size(Maximum)597.888mmVertical scan range 48-75HzVertical Scan Size(Maximum)336.312mmOptimal preset resolution 1920x1080@60HzMax resolution1920x1080@75HzPlug & Play VESA DDC2B/CIInput Connector HDMI/DPPower Source 19Vdc, 1.31APower ConsumptionTypical (default brightness and contrast)23WMax. (brightness = 100, contrast =100)28WPower saving≤0.3WPhysical Characteristics Connector Type HDMI/DP/Earphone out Signal Cable Type DetachableEnvironmental TemperatureOperating 0°~ 40°Non-Operating -25°~ 55°HumidityOperating 10% ~ 85% (non-condensing)Non-Operating 5% ~ 93% (non-condensing) AltitudeOperating 0~ 5000 m (0~ 16404ft )Non-Operating 0~ 12192m (0~ 40000ft )Panel Viewable Image Size68.47 cm diagonalPixel pitch 0.2331mm(H) x 0.2331mm(V) Video HDMI lnterface & DP Interface Display Color 16.7M ColorsOthers Horizontal scan range 30k-114kHzHorizontal scan Size(Maximum)596.74mmVertical scan range 48-75HzVertical Scan Size(Maximum)335.66mmOptimal preset resolution 2560x1440@60HzMax resolution2560x1440@75HzPlug & Play VESA DDC2B/CIInput Connector HDMI/DPPower Source 19Vdc, 2.37APower ConsumptionTypical (default brightness and contrast)30WMax. (brightness = 100, contrast =100)40WPower saving≤0.3WPhysical Characteristics Connector Type HDMI/DP/Earphone out Signal Cable Type DetachableEnvironmental TemperatureOperating 0°~ 40°Non-Operating -25°~ 55°HumidityOperating 10% ~ 85% (non-condensing)Non-Operating 5% ~ 93% (non-condensing) AltitudeOperating 0~ 5000 m (0~ 16404ft )Non-Operating 0~ 12192m (0~ 40000ft )Preset Display Modes 24T1Q/27T1QSTANDARD RESOLUTION HORIZONTALFREQUENCY(kHz)VERTICAL FREQUENCY(Hz)VGA640x480@60Hz31.46959.94 VGA640x480@67Hz3566.667 VGA640x480@72Hz37.86172.809 VGA640x480@75Hz37.575 VGA640x480@100Hz51.0899.769 VGA640x480@120Hz61.91119.518 DOS MODE720x400@70Hz31.46970.087 DOS MODE720x480@60Hz29.85559.710 SD720x576@50Hz31.2550 SVGA800x600@56Hz35.15656.25 SVGA800x600@60Hz37.87960.317 SVGA800x600@72Hz48.07772.188 SVGA800x600@75Hz46.87575 SVGA800x600@100Hz63.68499.662 SVGA800x600@120Hz76.302119.97 SVGA832x624@75Hz49.72574.551 XGA1024x768@60Hz48.36360.004 XGA1024x768@70Hz56.47670.069 XGA1024x768@75Hz60.02375.029 XGA1024x768@100Hz81.57799.972 XGA1024x768@120Hz97.551119.989 WXGA+1440x900@60Hz55.93559.887 SXGA1280x1024@60Hz63.98160.02 SXGA1280x1024@75Hz79.97575.025 HD1280x720@50HZ37.07149.827 HD1280x720@60HZ4560 HD1280x1080@60Hz67.17359.976 CVT1680x1050@60Hz64.67459.883 Full HD1920x1080@60Hz67.560 Full HD1920x1080@75Hz83.89474.973Q27T1STANDARD RESOLUTION HORIZONTALFREQUENCY(kHz)VERTICAL FREQUENCY(Hz)VGA640x480@60Hz31.46959.94 VGA640x480@67Hz3566.667 VGA640x480@72Hz37.86172.809 VGA640x480@75Hz37.575 DOS MODE720x400@70Hz31.46970.087 DOS MODE720x480@60Hz29.85559.710 SD720x576@50Hz31.2550 SVGA800x600@56Hz35.15656.25 SVGA800x600@60Hz37.87960.317 SVGA800x600@72Hz48.07772.188 SVGA800x600@75Hz46.87575 SVGA832x624@75Hz49.72574.551 XGA1024x768@60Hz48.36360.004 XGA1024x768@70Hz56.47670.069 XGA1024x768@75Hz60.02375.029 SXGA1280x1024@60Hz63.98160.02 SXGA1280x1024@75Hz79.97575.025 Full HD1920x1080@60Hz67.560 QHD2560x1440@60Hz88.78759.951 QHD2560x1440@75Hz111.02874.968 XGA1024x768@75Hz60.24174.927Pin AssignmentsPin No.Signal Name Pin No.Signal Name Pin No.Signal Name1.TMDS Data 2+9.TMDS Data 0-17.DDC/CEC Ground2.TMDS Data 2 Shield10.TMDS Clock +18.+5V Power3.TMDS Data 2-11.TMDS Clock Shield19.Hot Plug Detect4.TMDS Data 1+12.TMDS Clock-5.TMDS Data 1Shield13.CEC6.TMDS Data 1-14.Reserved (N.C. on device)7.TMDS Data 0+15.SCL8.TMDS Data 0 Shield16.SDA20-Pin Color Display Signal CablePin No.Signal Name Pin No.Signal Name 1ML_Lane 3 (n)11GND2GND12ML_Lane 0 (p)3ML_Lane 3 (p)13CONFIG14ML_Lane 2 (n)14CONFIG25GND15AUX_CH(p)6ML_Lane 2 (p)16GND7ML_Lane 1 (n)17AUX_CH(n)8GND18Hot Plug Detect9ML_Lane 1 (p)19Return DP_PWR10ML_Lane 0 (n)20DP_PWRPlug and PlayPlug & Play DDC2B FeatureThis monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.29。

Philips Signage Solutions Multi-Touch Display65"Powered by Android Multi-touch65BDL3552TInteractive classroom displayFeaturing multi-touch technologyMaximise engagement and inspire collaboration with an interactive Philips T-Line display. Featuring anti-glare toughened glass, these Android-powered displays are made to withstand heavy daily usage and feature up to 20 touchpointsInteractive and collaborative•Multi-touch technology capable of 20 touchpoints •Advanced IR touch with smaller, shallower bezels•Operate, monitor and maintain with CMND and Control Smart and powerful•Anti-glare toughened glass•OPS slot allows for PC embedding without cabling •Whiteboard mode built in•Wireless screen sharing and advanced collaboration•Android: Run your own app or choose your favourite app to runHighlightsMulti-touch technologyCreate a memorable interactive experience with up to 20 touchpoints at the same time. Perfect for collaborative and competitive applications, this display connects youraudience with any content - making it ideal for education, public venues, corporate,hospitality and retail settings. The touch panel is HID compliant, providing true plug-and-play operation.OPS slotIntegrate a full-power PC or Android-powered CRD50 module directly into your Philips Professional Display. The OPS slot contains all the connections you need to run your slot-in solution, including a power supply.CMND and ControlRun your display network over a local (LAN) connection. CMND and Control allows you to perform vital functions like controlling inputs and monitoring display status. Whether you're in charge of one screen or 100.Whiteboard mode built inInspire agile collaboration with whiteboard mode. Simply activate this feature to turn your display into a blank canvas that can be drawn on by multiple users by hand or with dedicated display markers. Everything on the screen can then be captured for easy printing or file sharing.Wireless screen sharingDisplay four feeds on the one screen. Wireless screen sharing allows you to connect multipledevices at the same time for quick content switching when you need it. Use your existing Wi-Fi network to instantly and securely connect devices or use our optional HDMI interact dongles to cast directly to the screen without needing to connect to your secured/protected network.Powered by AndroidWith Android OS integrated into the display, you can work with the most developed OS on the planet and save your own app directly into the display. Or, choose from the large library of Android apps and play content from there. With the built-in scheduler, you can daypart your apps and content based on yourcustomer and time of day and with the auto-orientation feature, showing content inportrait or landscape is as simple as turning thedisplay.Issue date 2022-07-15Version: 13.0.112 NC: 8670 001 66454EAN: 87 12581 76594 1© 2022 Koninklijke Philips N.V.All Rights reserved.Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V. or their respective owners.SpecificationsPicture/Display•Diagonal screen size: 64.5 inch / 163.9 cm •Panel resolution: 3840 x 2160•Optimum resolution: 3840 x 2160 @ 60 Hz •Brightness: 420 cd/m²•Contrast ratio (typical): 1300:1•Surface treatment: Anti-Glare coating •Aspect ratio: 16:9•Response time (typical): 9 ms •Pixel pitch: 0.372 x 0.372 mm •Display colours: 1.07 Billion•Viewing Angle (H / V): 178 / 178 degree•Picture enhancement: 3/2 - 2/2 motion pull down, 3D Combfilter, Motion compens. deinterlacing, Progressive scan, 3D MA deinterlacing, Dynamic contrast enhancement•Dynamic contrast ratio: 500,000:1•Panel technology: IPS•Operating system: Android 9Interactivity•Multi-touch technology: Advanced infrared touch •Touch points: 20 simultaneous touch points •Plug and play: HID compliant•Protection glass: Tempered safety glass, Anti-GlareConnectivity•Video input: Display Port1.2 (x 1), DVI-I (x 1), HDMI 2.0 (x 4), USB 2.0 (x 2), USB 3.0 (x 2), USB-C, HDMI 2.0 (x 2)•Audio input: 3.5 mm Jack (x 1)•Audio output: 3.5 mm Jack (x 2)•External control: RJ45, IR (in/out) 3.5 mm jack, RS232C (in/out) 2.5 mm jack•Other connections: micro SD, OPS•Video output: DisplayPort 1.2 (x 1), DVI - D (x 1), HDMI 2.0 (x 1), USB 2.0 (x 2)Supported Display Resolution•Computer formatsResolutionRefresh rate 1024 x 768 60, 70 Hz 1152 x 864 60, 70, 75 Hz 1152 x 900 66 Hz 1280 x 720 60, 70 Hz 1280 x 768 60 Hz, 75 Hz 1280 x 800 60, 75 Hz 1280 x 960 60 Hz 1280 x 1024 60, 67, 75 Hz1360 x 76860 Hz 1366 x 768 60 Hz 1400 x 1050 60, 75 Hz 1440 x 1050 60 Hz 1440 x 900 60, 75 Hz 1600 x 1200 60 Hz 1600 x 900 60 Hz 1680 x 1050 60 Hz 1920 x 1080 60 Hz 1920 x 1200 60 Hz3840 x 2160 24, 25, 30, 60 Hz 640 x 350 70 Hz640 x 480 60, 67, 72, 75 Hz 800 x 600 56, 60, 72, 75 Hz 832 x 624 75 Hz 848 x 480 60 Hz 960 x 720 75 Hz •Video formats Resolution Refresh rate 1080i 50, 60 Hz 1080p 50, 60 Hz 480p 60 Hz 4K x 2K 576p 50 Hz 720p 50, 60 Hz 720p60 HzConvenience•Placement: Landscape (18/7), Portrait (12/7)•Signal loop through: IR Loop through, DisplayPort, RS232•Network controllable: RS232, RJ45•Picture performance: Advanced colour control •Screen-saving functions: Pixel Shift, Low Brightness •Keyboard control: Hidden, Lockable •Remote control signal: Lockable•Energy-saving functions: Smart Power •Other convenience: Carrying handles •Ease of installation: Smart InsertDimensions•Set dimensions (W x H x D):1494.30 x 869.40 x 80.2 mm (D@wall mount)/106.8 mm (D@speaker cover) mm •Product weight: 43.6 kg•Wall Mount: 400(H)x400(V), M8•Bezel width:16.30 mm(even)•Product weight (lb): 96.12 lb•Set dimensions in inch (W x H x D):58.83 x 34.23 x 3.16 (D@wall mount)/4.20 (D@speaker cover) inch•Smart Insert mount: 100 mm x 100 mm, 6 x M4L6Sound•Built-in speakers: 2 x 20 W RMSOperating conditions•Temperature range (operation): 0 ~ 40 °C•Relative humidity: 20–80% (Operational), 5–95% (Storage) %•MTBF: 50,000 hour(s)•Altitude: 0 ~ 3000 m•Temperature range (storage): -20 ~ 60 °CPower•Mains power: 100 ~ 240 VAC, 50 ~ 60 Hz •Standby power consumption: <0.5 W •Power Saving Features: Smart Power •Consumption (Typical): 175 W •Consumption (Max): 350 W •Energy Label Class: GAccessories•Included accessories: AC Power Cord, RS232 cable, Remote Control, Batteries for remote control, Quick start guide, HDMI cable, IR sensor cable (1.8 M)•Included Accessories: RS232 daisy-chain cable, Cleaning cloth (x 1), DVI-D cable (1.8 m), M2 Screw (x 2), M3 screw (x 2), Philips logo (x 1), Touch Pen (x 2), Touch USB (x 1), USB Cover (x 1)•Optional accessories: Cast to dongleMiscellaneous•On-Screen Display Languages: Arabic, English, French, German, Italian, Japanese, Polish, Spanish, Turkish, Russian, Simplified Chinese, Traditional Chinese, Danish, Dutch, Finnish, Norwegian, Portuguese, Swedish•Regulatory approvals: BSMI, CB, CE, EMF, ETL, FCC, Class A, PSB, RoHS, EAC •Warranty:3 year warrantyMultimedia Applications•USB Playback Picture: BMP, JPEG, JPG, PNG •USB Playback Audio: AAC, M4A, MP3, WMA •USB Playback Video: ASF, AVI, DAT, FLV, MKV, MP4, MPEG, MPG, TS, VOB, WEBM, WMVInternal Player•CPU:MTK5680•Storage: 32 GB eMMc•Wi-Fi: AP(WC0SR2511-88112BU), STA(WCT5GM2511MT7668AU)•GPU: DDR4 4 GB •Memory:4 GB RAM。

User's GuideRevision 1.0AOC-S25G-m2SUser's Guide Revision 1.0 Release Date: March 16, 2017Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document.Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.Copyright © 2017 by Super Micro Computer, Inc. All rights reserved.Printed in the United States of AmericaThe information in this User's Guide has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this user's guide, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this user's guide, please see our Website at .Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this user's guide at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.Any disputes arising between the manufacturer and the customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See /hazardouswaste/perchlorate”.WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.PrefacePrefaceAbout this User's GuideThis user's guide is written for system integrators, IT technicians and knowledgeable end users. It provides information for the installation and use of the AOC-S25G-m2S add-on card.About this Add-on CardThe Supermicro AOC-S25G-m2S is a leading edge 25GbE controller. Based on the Mellanox ConnectX®-4 Lx EN chipset with features such as VXLAN and NVGRE, it is backward compatible with 10GbE networks and addresses bandwidth demand from virtualized infrastructures in data centers or cloud deployments. It supports the RoCE specification with CPU offload, delivering low-latency and high-performance over Ethernet networks. Supermicro® Asset Management and thermal detection give an extra layer of controller health management and peace of mind. The Supermicro AOC-S25G-m2S high performance 25GbE adapter solution is an excel-lent choice to enhance network connectivity in data centers and enterprise environ-ments. For more information regarding product support or updates, please refer to our website at /products/nfo/networking.cfm#adapter.An Important Note to the UserAll images and layouts shown in this user's guide are based upon the latest PCB Revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this user's guide.Returning Merchandise for ServiceA receipt or copy of your invoice marked with the date of purchase is required beforeany warranty service will be rendered. You can obtain service by calling your ven-dor for a Returned Merchandise Authorization (RMA) number. When returning the motherboard to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and the shipping package is mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete. For faster service, you can also requesta RMA authorization online (/RmaForm/).This warranty only covers normal consumer use and does not cover damages in-curred in shipping or from failure due to the alternation, misuse, abuse or improper maintenance of products.During the warranty period, contact your distributor first for any product problems.Conventions Used in the User's GuidePay special attention to the following symbols for proper system installation and to prevent damage to the system or injury to yourself:Warning: Important information given to ensure proper system installationor to prevent damage to the components or injury to yourself.Note: Additional information given to differentiate between various modelsor provides information for correct system setup.Naming ConventionSMC Networking Add-on Cards Preface–1 –234 –56 7Character Representation Options1st Product Family AOC: Add On Card2nd Form Factor S: Standard, P: Proprietary, C: MicroLP, U: UIO3rd Product Type/Speed G: GbE (1Gb/s), TG: 10GbE (10Gb/s), 40G: 40GbE(40Gb/s), IBF: FDR IB (56Gb/s), IBQ: QDR IB (40Gb/s) 4th Chipset Model (Optional)N: Niantec (82599), P: Powerville (i350),S: Sageville (X550), F: Fortville (XL710)5th Chipset Manufacturer i: Intel, m: Mellanox, b: Broadcom6th Number of Ports1: 1 port, 2: 2 ports, 4: 4 ports7th Connector Type (Optional)S: SFP+, T: 10GBase-T, Q: QSFP+, C: QSFP28Contacting SupermicroHeadquartersAddress:Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel:+1 (408) 503-8000Fax:+1 (408) 503-8008Email:************************(GeneralInformation)**********************(TechnicalSupport) Website:EuropeAddress:Super Micro Computer B.V.Het Sterrenbeeld 28, 5215 ML's-Hertogenbosch, The NetherlandsTel:+31 (0) 73-6400390Fax:+31 (0) 73-6416525Email:*******************(GeneralInformation)*********************(TechnicalSupport)*****************(CustomerSupport) Website:www.supermicro.nlAsia-PacificAddress:Super Micro Computer, Inc.3F, No. 150, Jian 1st Rd.Zhonghe Dist., New Taipei City 235Taiwan (R.O.C)Tel:+886-(2) 8226-3990Fax:+886-(2) 8226-3992Email:**********************.twWebsite:PrefaceTable of ContentsPrefaceChapter 1 Overview1-1 Overview .........................................................................................................1-1 1-2 Key Features ...................................................................................................1-1 1-3 Specifications ..................................................................................................1-2 General ............................................................................................................1-2 Host Interface ..................................................................................................1-2 Networking Features .......................................................................................1-2 CPU Offload Features.....................................................................................1-3 Overlay Networks ............................................................................................1-3 Hardware-Based I/O Virtualization ..................................................................1-3 Storage Offloads .............................................................................................1-3 Management Features ....................................................................................1-3 Virtualization Features.....................................................................................1-4 Operating System Support ..............................................................................1-4 Remote Boot ...................................................................................................1-4 Operating Conditions ......................................................................................1-4 Physical Dimensions .......................................................................................1-5 Weight .............................................................................................................1-5 Supported Platforms .......................................................................................1-5 Compliance/Environmental .............................................................................1-5 1-4 Similar Products ..............................................................................................1-6 1-5 Optional Parts List ...........................................................................................1-6 Chapter 2 Hardware Components2-1 Add-On Card Image and Layout .....................................................................2-1 2-2 Major Components ..........................................................................................2-2 2-3 SFP28 Ethernet Connections..........................................................................2-3 2-4 NC-SI Header & PCI-E 3.0 x8 Golden Finger ................................................2-4 Chapter 3 Installation3-1 Static-Sensitive Devices ..................................................................................3-1 3-2 Before Installation ...........................................................................................3-2 3-3 Installing the Add-on Card ..............................................................................3-2 3-4 Installing Drivers from the CD-ROM CDR-NIC ...............................................3-3 Windows Drivers .............................................................................................3-4 3-5 Installing Drivers ............................................................................................3-4 Linux Drivers ...................................................................................................3-4 Firmware Update Procedures .........................................................................3-5NotesChapter 1: OverviewChapter 1Overview1-1 OverviewCongratulations on purchasing your add-on card from an acknowledged leader in the industry. Supermicro products are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. For product support and updates, please refer to our website at / products/nfo/networking.cfm#adapter.1-2 Key FeaturesThe key features of this add-on card include the following:• Dual SFP28 Connectors• Low-Profile, Short Length Standard Form Factor• PCI-E 3.0 x8• Mellanox ConnectX®-4 Lx EN Ethernet Controller• Asset Management Features with thermal sensor• Hardware offloads for VXLAN, NVGRE and GENEVE encapsulated traffic • Low latency RDMA over Converged Ethernet (RoCE)• PCI-SIG SR-IOV compliant• Jumbo Frames support up to 9.6kB• PXE support• Erasure Coding Offload• NC-SI for IPMI support• RoHS compliant 6/61-3 SpecificationsGeneral• Mellanox ConnectX®-4 Lx EN dual-port 25Gbps controller • Compact size low-profile standard form factor• PCI-E 3.0 x8 (8GT/s, 5GT/s or 2.5GT/s) interface • Dual SFP28 connectors• Typical power consumption: 8.7WHost Interface• PCI-E 3.0 x8• Message Signal Interrupt (MSI-X)Networking Features• 25G Ethernet Consortium 25 Gigabit Ethernet• IEEE 802.3ae 10 Gigabit Ethernet• IEEE 802.3az Energy Efficient Ethernet• IEEE 802.3ap based auto-negotiation and KR startup • IEEE 802.ad, 802.1AX Link Aggregation• IEEE 802.1Q, 802.1p VLAN tags and priority• IEEE 802.1Qau (QCN) – Congestion Notification • IEEE 802.1Qaz (ETS)• IEEE 802.1Qbb (PFC)• IEEE 802.1Qbg• IEEE 1588v2Chapter 1: Overview • Jumbo frame support (9.6KB)CPU Offload Features• RDMA over Converged Ethernet (RoCE)• TCP/UDP/IP stateless offload• LSO, LRO, checksum offload• RSS, TSS, HDS, VLAN insertion/stripping. Receive flow steering• Intelligent interrupt coalescenceOverlay Networks• Stateless offloads for overlay networks and tunneling protocols• Hardware offload of encapsulation and decapsulation of NVGRE and VXLAN overlay networksHardware-Based I/O Virtualization• Single Root IOV• Multi-function per port• Address translation and protection• Multiple queues per virtual machine• Enhanced QoS for vNICs• VMware NetQueue supportStorage Offloads• RAID offload – erasure coding (Reed-Solomon) offloadManagement Features• Asset Management features with thermal sensor• NC-SI for IPMI SupportVirtualization Features• SR-IOV: up to 256 Virtual Functions• SR-IOV: up to 16 Physical Functions per port• 1K ingress and egress QoS levels• Guaranteed QoS for VMsOperating System Support• RHEL/CentOS• Windows• FreeBSD• VMware• OpenFabrics Enterprise Distribution (OFED)• OpenFabrics Windows Distribution (WinOF-2)Remote Boot• Remote boot over iSCSi• PXE and UEFIOperating Conditions• Operating temperature: 0°C to 55°C (32°F to 131°F)• Storage temperature: -40°C to 70°C (-40°F to 158°F)• Storage humidity: 90% non-condensing relative humidity at 35°CChapter 1: Overview Physical Dimensions• Card PCB dimensions: 14.2cm x 6.89cm (5.6in x 2.71in) (LxW)• Height of end brackets: standard – 12cm (4.725in), low-profile – 8cm (3.15in)Weight• 89.58g (0.1975lb)Supported Platforms• Motherboards with minimum PCI-E 3.0 x8 expansion slot• Server Systems with low-profile or full-height PCI-E 3.0 x8 expansion slots • NC-SI feature is only supported by Supermicro® motherboards with correspond-ing NC-SI connectorsNote: This product is intended to be used with Supermicro server systemsor motherboards as an integrated solution package.Compliance/Environmental•RoHS Compliant 6/6, Pb Free1-4 Similar Products1-5 Optional Parts ListChapter 2: Hardware ComponentsChapter 2Hardware Components2-1 Add-On Card Image and LayoutThe AOC-S25G-m2S LayoutThe AOC-S25G-m2S Image1. Mellanox ConnectX®-4 Lx EN 5. SFP28 Port2 Link LED2. SFP28 Port1 6. NC-SI header3. SFP28 Port27. PCI-E 3.0 x84. SFP28 Port1 Link LED12345672-2 Major ComponentsThe following major components are installed on the AOC-S25G-m2S:1. Mellanox ConnectX®-4 Lx EN Controller2. Dual SFP28 (Small Form Factor Pluggable) Ports3. Two (2) SFP28 Link/Activity LED Indicators4. NC-SI for IPMI supportChapter 2: Hardware Components1. SFP1: SFP28 Port12. SFP2: SFP28 Port23. SFP28 Port1 Link LED4. SFP28 Port1 Link LED2-3 SFP28 Ethernet ConnectionsSFP28 (SFP1/SFP2) ConnectorsTwo small form-factor pluggable (SFP28) optical transceiver connectors (SFP1/SFP2) are located on the add-on card. These SFP28 ports provide Ethernet up to 25GbE network connections. See the layout below for the locations.SFP28 (SFP1/SFP2) Link/Activity LED IndicatorsTwo LAN Link/Activity LED indicators are located at PORT1 LED and PORT2 LED on the add-on card. PORT1 LED is used for the SFP28 SFP1 connector, and PORT2 LED, for SFP28 SFP2 connector. See the table below for the LED states.2-4 NC-SI Header & PCI-E 3.0 x8 Golden FingerNC-SI HeaderA Network-Controller Sideband Interface (NC-SI) header is located at JNCSI1 on the add-on card. Connect an appropriate cable from this header to a motherboard to provide the out-of-band (sideband) connection between the onboard Baseboard Management Controller (BMC) and a Network Interface Controller (NIC) for remote management. For the network sideband interface to work properly, you will need to use a motherboard that supports NC-SI and also need to have a special cable. Please contact Supermicro at to purchase the cable for this header. See the layout below for the location of the JNCSI1 header.PCI-E 3.0 x8 Golden FingerA PCI-E 3.0 x8 Golden Finger is located at JGF1 on the add-on card. Insert this connector into a PCI-E 3.0 x8 slot on a motherboard to use this add-on card. See the layout below for the location.1. NS-CI Header2. PCI-E3.0 x8 Golden FingerChapter 3: InstallationChapter 3Installation3-1 Static-Sensitive DevicesElectrostatic Discharge (ESD) can damage electronic com p onents. To avoid dam-aging your add-on card, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.Precautions• Use a grounded wrist strap designed to prevent static discharge.• Touch a grounded metal object before removing the add-on card from the antistatic bag.• Handle the add-on card by its edges only; do not touch its components, or peripheral chips.• Put the add-on card back into the antistatic bags when not in use.• For grounding purposes, make sure that your system chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the add-on card.UnpackingThe add-on card is shipped in antistatic packaging to avoid static damage. When unpacking your component or your system, make sure that the person handling it is static protected.Warning: To avoid damaging your components and to ensure properinstallation, be sure to always connect the power cord last, and alwaysremove it before adding, removing or changing any hardware components.3-2 Before InstallationTo install the add-on card properly, be sure to follow the instructions below.1. Power down the system.2. Unplug the power cord.3. Use industry standard anti-static equipment (such as gloves or wrist strap)and follow the precautions on Page 3-1 to avoid damage caused by ESD.4. Familiarize yourself with the server, motherboard, and/or chassis documenta-tion.5. Confirm that your operating system includes the latest updates and hotfixes.3-3 Installing the Add-on CardFollow the steps below to install the add-on card into your system.1. Remove the server cover and, if any, set aside any screws for later use.2. Remove the add-on card slot cover. If the case requires a screw, place thescrew aside for later use.3. Position the add-on card in the slot directly over the connector, and gentlypush down on both sides of the card until it slides into the PCI connector.4. Secure the add-on card to the chassis. If required, use the screw that youpreviously removed.5. Attach any necessary external cables to the add-on card.6. Replace the chassis cover.7. Plug the power cord into the wall socket and power up the system.Chapter 3: InstallationNote: If the FOUND NEW HARDWARE WIZARD screen displays on yoursystem, click CANCEL.3. Click on INSTALL DRIVERS AND SOFTWARE.4. The Install Shield Wizard will start .Follow the prompts to complete the instal-lation.3-4 Installing Drivers from the CD-ROM CDR-NICFollow the steps below to install the drivers needed for your Windows OS support. The controller comes with a driver on the CD-ROM CDR-NIC.1. Run the CDR-NIC. (If you do not have a product CD-ROM, download driversfrom the Supermicro Support Website and then transfer them to your system.)2. When the SUPERMICRO window appears, click on the computer icon next tothe product model.3-5 Installing DriversUse the procedures below to install drivers for the AOC-S25G-m2S add-on card for both Linux and Windows.Linux DriversUse the following procedures to install drivers on the Linux operating system.Installing 25G Drivers for the Linux Operating System1. From the CDR-NIC LAN driver CD, go to the following directory: Mellanox> Linux. You may also go to the Supermicro FTP site at ftp://ftp.super-/Networking_Drivers/CDR-NIC_1.50_for_Add-on_NIC_Cards/Mellanox/25GbE/Linux/.2. Download the Linux driver package file.3. Install the driver by entering the following commands:tar xzvf mlnx-en–<ver>.tgzcd mlnx-en–<ver>./install.shThis installs the Linux drivers to your system.Note: Driver installation may require root privileges.Windows DriversUse the following procedures to install drivers on the Windows operating system.Installing 25G Drivers for the Windows Operating System1. From the CDR-NIC LAN driver CD, go to the following directory: Mellanox> Windows. You may also go to the Supermicro FTP site at ftp://ftp.super-/Networking_Drivers/CDR-NIC_1.50_for_Add-on_NIC_Cards/Mellanox/25GbE/Windows/.2. Choose the desired Windows driver package file.3. Double -click to run and install the executable (.exe ) file in the driver pack-age.4. The Install Shield Wizard will start .Follow the prompts to complete the instal-lation.Chapter 3: InstallationFirmware Update ProceduresUse the following procedures for updating the AOC-S25G-m2S add-on card firm-ware for both the Linux and Windows operating systems.Updating Firmware for the Linux Operating System1. From the CDR-NIC LAN driver CD, go to the following directory: MellanoxFirmware_Tool > Linux. You may also go to the Supermicro FTP site at ftp:// /Networking_Drivers/CDR-NIC_1.50_for_Add-on_NIC_Cards/Mellanox/Firmware_Tool/Linux/.2. Choose the MFT Linux package file and untar the package file.3. Install the package by entering the following command:cd mft–<ver>./install.sh4. Install the firmware by the following commands:mst startmst status *write down the pci_cr0 device name*flint –d <pci_cr0 device name> –i <firmware file name>.bin burnUpdating Firmware for the Windows Operating System1. From the CDR-NIC LAN driver CD, go to the following directory: MellanoxFirmware_Tool > Linux. You may also go to the Supermicro FTP site at ftp:// /Networking_Drivers/CDR-NIC_1.50_for_Add-on_NIC_Cards/Mellanox/Firmware_Tool/Windows/.2. Choose the desired MFT Windows package file.3. Double-click to run and install the MFT package file.4. Open the DOS command prompt and locate the MFT folder.5. Install the firmware by entering the following commands:mst startmst status *write down the pci_cr0 device name*flint –d <pci_cr0 device name> –i <firmware file name>.bin burn(Disclaimer Continued)The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com-munication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous ap-plications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.。

显示器尺寸对应的最佳分辨率AOC V24t详细参数切换到传统表格版基本参数显示参数面板控制接口其它显示器附件保修信息基本参数•产品定位：娱乐影音•屏幕尺寸：23.6英寸•屏幕比例：16:9（宽屏）•最大分辨率：1920x1080 •最佳分辨率：1920x1080•高清标准：1080p（全高清）•面板类型：TN•背光类型：CCFL背光•动态对比度：60000:1•黑白响应时间：5ms显示参数•点距：0.2715mm•亮度：300cd/㎡•可视面积：521.28×293.22mm •可视角度：170/160°•显示颜色：16.7M•扫描频率：水平：30-80KHz 垂直：55-75Hz•带宽：148.5MHz面板控制•控制方式：按键•语言菜单：英文，德语，法语，意大利语，西班牙语，俄语，葡萄牙语，土耳其语，简体中文接口•视频接口：D-Sub（VGA），HDMI，色差，S端子，复合信号CVBS •其它接口：TV，音频输出外观设计•机身颜色：黑色烤漆，银色底座•外观设计：超薄设计，最薄处2.5cm•产品尺寸：595.4×483.54×220.13mm（包含底座）668×565×117mm（包装）•产品重量：5.5kg（净重）7.5kg（毛重）•底座功能：倾斜•音箱：内置音箱（2×2.5W）•壁挂：100×100mm其它•电视功能：支持电视功能•HDCP：支持HDCP•电源性能：90~240V交流, 50/60Hz External Adapter •消耗功率：最大:60W待机:1W•安规认证：CCC, CB, CE, GOST，EPA•其它性能：仰角：-3-10度•其它特点：Eco Mode 5种亮度情景模式获得EPEAT金奖•上市时间：2009年06月显示器附件•包装清单：显示器主机x1 底座x1电源线x1信号线x1保修卡x1电子光盘说明书x1保修信息•保修政策：全国联保，享受三包服务•质保时间：3年•质保备注：整机1月内包换，2年免费上门，3年免费全保•客服电话：400-887-8007•电话备注：8:00-22:00•详细内容：在中国大陆（不包括香港、澳门特别政区）购买并在大陆地区使用的显示器，出现保修范围内的硬件故障时，凭显示器保修证正本和购机发票到“冠捷国内维修站一览表”中的任何一个维修站均可享受1个月包换，2年在规定的城市地区免费上门维修服务，3年免费保修（包含CRT及LCD面板）的123保修服务。

AOC AGM700 RGB Gaming MouseUSER'S GUIDEVer.:1.00CAUTION: To use this product properly, please read the user's guide before installing. ContentsPACKAGE CONTENTS/SYSTEM REQUIREMENTSPackage Contents◼AGM700 FPS Gaming Mouse◼Five Pieces 5g Weight Module◼Quick Setup GuideProduct System Requirements◼Windows® 7/8/8.1/10 or macOS◼Available USB port◼160MB free hard disk space◼Internet connectionAOC G-Tools System Requirements◼Windows® 7 or above◼160MB free hard disk space◼Internet connectionTechnical Support◼2 years limited warranty◼Free online technical support at TECHNICAL SPECIFICATIONSSpecifications◼Advanced optical sensor with true 16000 DPI◼Switchable DPI - 1600/3200/6400/12800/16000/smart DPI (default 1600 DPI) ◼Up to 400 inches per second (IPS) and 50g acceleration◼8 programmable buttons◼Omron mechanical switch with up to 50 million clicks lifespan◼UP to 1000 Hz/1 ms report rate◼Enquired with weight module can easy for weight adjustment◼Customizable RGB lighting effect syncing with other AOC gaming devices◼ 1.8 M braided cableApproximate Size & Weight◼Length: 129.50 mm/ 4.95 in◼Width: 65.32 mm/ 2.57 in◼Height: 42.30 mm/ 1.66 in◼Weight: 173 g/0.38 lbs◼Cable Length: 1.8 m/ 5.9 ftOperating Environment◼Operating Temperature: 0 ° C (32 ° F) to 40 ° C (104 ° F)◼Operating Humidity: 10% - 85%Device LayoutA.Left ButtonB.Right ButtonC.Middle Button/Scroll WheelD.Browser ForwardE.Browser BackwardF.DPI CycleG.Mode SwitchH.DPI ShiftI.True 16,000 DPI Optical Sensor J.Smooth Mouse FeetK.Weight ModuleAOC G-TOOLS INSTALLATIONStep 1: Plug the device into a USB port on your computer.Step 2: The computer operating system will automatically detect the device.Step 3: Download AOC G-Tools. Browse to and search for "AOC G-Tools."Step 4:Start the installation process by clicking on the file “Setup.exe”.Step 5: Windows® will prompt you if installation should continue; install the driver despite this.Note: The driver will automatically uninstall any previous version of the driver; for this reason, it may take some time for the driver to install before you may begin programming the device.Step 6: When the installation process is complete, please reboot your computer system.Step 7: The AOC G-Tools icon is displayed in the Windows® taskbar while it is running. Access the Configuration menu by right-clicking the AOC G-Tools icon.AOC G-TOOLS INTRODUCTIONGame Profile ManagementUnder Game Profile Management, you may export a customized profile by clicking the Exportbutton, or import a profile from your computer by clicking the Import button.The default profile names are Profile 1 through Profile 5. You may rename your profiles by typing in the text field below Profile Name.Each game profile supports seven macro keys, and the on-board memory of the device supports three profiles.Each profile may be activated along with a linked program. To do so, put the executable path of the program you want to link in the Path To Executable (*EXE) text field.Reset To Factory Default SettingsBy clicking the ‘GO’ button, the device will be reset to the factory default settings.ButtonsFor each numbered button, you may assign an action from its drop-down menu. Options listed in the drop-down menu are explained below.◼Macro ManagerA macro is a prerecorded sequence of keystrokes and button presses executed with precise timing. By assigning a macro to a button, you can execute complex combinations with ease. The device allows you to create, delete, import, and export your customized macros. When choosing this option from the drop-down menu, the Macro Manager window will appear. You may select an existing macro as the assignment to the button, or record a new macro and assign it to the button. If you like to perform the assignment later, c lick the Macro Manager button in the lower right corner, the Macro Manager window will show for your further operations as below.1. Create a Macro(1)Click the button and name the macro youare about to record. Confirm the name bypressing the Enter key on your keyboard.(2)Set the delay time between events:-Recording: The delay between events areregistered as they are recorded.-Fixed: Use a predefined time (shown inmillisecond) for the delay.-Ignore: Omit all the pauses betweenkeystrokes and button presses.(3)Click the Start button to record all yourkeystrokes and mouse button commands into the macro. When done, click the Stop button to complete this recording.(4)Click the Cancel button if you want to discard this recording, or the Ok button to confirm thisrecording. Successfully recorded macros can be found from the Macro Select drop-down list. (5)For any recorded macro, you may delete or adjust its event sequences, or add new events byinitiating another recording session.2. Delete a MacroSelect the macro to be deleted and click on the Trash Binbutton down below. A message window will pop up to confirm your decision. Click the Ok button to delete the macro.3. Edit DelayTo adjust the delay time, double-click the field to be revised and enter the new value. Some games may not be able to detect short delays.4. Delete Record ActionsTo delete a single or multiple actions or delay time of the macro, click the trash bin button.5. Insert Macro ItemClick the button to start inserting another macro to an existing macro. Choose to record this new macro before or after the existing one; then click the Start button to start the recording. When done, click the Stop button to complete the session, or the Save button to keep the recording. You may also insert delay time before/after the selected event. After entering the desired time value, click the Save button.◼MultimediaOpen Player: Start media player.Pre Track: Toggle to the previous media track. Next Track: Toggle to the next media track.Play/Pause: Toggle between playing and pausing media. Stop: Stop playing the media.Mute: Mute (turns off) the computer sound.Volume +: Increase the computer sound volume. Volume -: Decrease the computer sound volume.◼DPI SwitchDPI Up: Increase the DPI. DPI Down: Decrease the DPI.DPI Cycle: Cycle between the 5 options of the G-Tools. DPI Shift: Predefined DPI at 400.◼Window ManagementCalculator: Start Microsoft Calculator. Email: Start the default mail program.WWW Favorites:Open the default web browser Favorites.WWW Forward: Go to the next webpage.WWW Back: Go to the previous webpage.WWW Stop: Stop loading webpage.My Computer: Open the My Computer window (or This PC for Win10).WWW Refresh: Refresh the current webpage.WWW Home: Start the default web browser and load the homepage.WWW Search: Go to the default web browser search bar or Search Windows.Show Desktop: Switch between desktop and the current view.◼Text EditorNine text commands are available: Cut, Copy, Paste, Undo, Select All, Find, New, Save, and Open.◼Left ClickPerform a left-click.◼Right ClickPerform a right-click.◼Middle ClickActivate the universal scrolling function.◼Browser BackwardPerform "Backward" command for most Internet browsers.◼Browser ForwardPerform "Forward" command for most Internet browsers.◼Double-ClickPerform a double-click action.◼Fire ButtonPerform a fire button until release.◼Assign a ShortcutAssign a shortcut combination.◼Windows KeyOpen the Start Windows menu.◼Smart KeyIf you assign a button with Smart Key function, while holding down the Smart Key, press the otherbutton, the Smart Key will repeat this button’s action continuously.◼Button OffSwitch off the button.Sensitivity◼DPI SettingYou may define five sets of DPI values ranged from 200 to 16000 to suit your needs. The set DPI values will be applied to the DPI cycle function. When a set value is currently in use, it will be highlighted in red, and the corresponding LED color will be shown on your device.The default values are as below:•DPI #1: 1600 DPI (Default)•DPI #2: 3200 DPI•DPI #3: 6400 DPI•DPI #4: 12800 DPI•DPI #5: 16400 DPI•DPI #6: SMART DPI◼Polling RateChoose from four polling rate options: 125Hz/8ms, 250Hz/4ms, 500Hz/2ms,1000Hz/1ms(default).◼Double ClickDrag the slider bar knob toward left (Slow) or right (Fast) to adjust the double-click speed.◼Windows Pointer SpeedDrag the slider bar knob toward left (Slow) or right (Fast) to adjust the Windows Pointer Speed. The set value will also be applied to the Windows Control Panel. We recommend the default setting.◼Scroll SpeedDrag the slider bar knob toward left (Slow) or right (Fast) to adjust the scrolling speed for viewing a document or webpage. To test the set value, press the Apply button and test in your browser.Light FX◼Light FXChoose from the Light FX drop-down menu for your favorite light setting. Options are: Static, Breathing, and Blink.◼LED SettingChoose the Random or Single LED lighting effect option to set continuously changing colors or a selected RGB color for the device. To restore the default light settings, press the Go button beside“Reset To Factory Default Settings”.Lighting colors cycle between 12 predefined colors.✓Single LED:To set the color, click the color square next to the Side Light/MainLight option, the Color Control windows will pop up. Point at any spoton the RGB panel to set your favorite color, or enter RGB values todefine the color. The LED color setting is available for Static, Breathing,and Blink effect.◼PulsationDrag the slider bar knob toward left (Slow) or right (Fast) to set up the speed of the lighting effect, three options are available from Slow to Fast.◼BrightnessDrag the slider bar knob toward left or right to set up the brightness of the lighting effect, four levels of lighting brightness are available from Off to Bright. This setting option is available for all of the lighting effects.Light FX SyncThe lighting effect of the device can be synchronized with other AOC gaming devices that support the AOC Light FX Sync. To sync the devices, select the icons of the devices of your choice and click the Apply button. The synchronized devices are highlighted in red.Reset To Factory Default SettingsBy clicking the GO button, the device will be reset to the factory default settings.Online UpdateWhen there are new updates available, a notice balloon will show on the upper right corner along with the tool icon.Click on the notice balloon, the Online Update pop-up window will show the update options. Select the updates to download and install. Click the Update button to complete the update process.SAFETY AND MAINTENANCEImportantFor your safety, please carefully read the following guidelines for the device:1.Do not operate the device under abnormal conditions.2.Avoid looking directly at the device's tracking beam or pointing the beam at anyone's eyes. Pleasenote that the tracking beam is not visible to the naked eye and is set as always-on.3.Do not disassemble the device (this will void the warranty) and do not attempt to operate underabnormal current loads.4.Keep the device away from liquid or moisture. Operate the device only within the indicatedtemperature range: 0 ° C (32 ° F) to 40 ° C (104 ° F). If the temperature of the device is too high, unplug the device to lower the temperature.5.If the RGB lighting is not running properly, or the device is not functioning, or if there is anabnormal thermal situation, troubleshoot the device by unplugging the device and plugging the device back in .6.If the troubleshooting process does not resolve the issue, unplug the device and visit for support. Do not attempt to repair the device yourself.SafetyFederal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may causeundesired operation.Note:This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the device and receiver.—Connect the device into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.。