模具常用中英文对照

模芯Parting Core 耐落胶Teflon Paste 局部视图Partial View 偏移量Offset冷料Cold Slag 水塞Water Line Plug 线切割Wire 撬模脚Ppy Slot轮廓Contour 重新加工Reworked 螺纹孔Tapping Hole 配件Components 连接件Fittings 补偿Compensation 斜针Angle Pin 平面度Parallel接合Engage 倒角Chamfer替换镶件Interchangeable Mold Inserts 模胚Mold Base指定吨位的注塑机Specific Press 热嘴Hotnozzle水嘴接头Water Fitting 火花机Edm螺纹Eyebolt Thread 熔接线Weildline回针Stop Pin 压机Press二级顶出针Sub-Leaderd Pin 嗮纹Texturing镶件Mold Insert 梯形Trapezoid加硬Harden 凸缘、法兰Flange 唧嘴Sprue 方铁Spacer Block 设计筒图Design Preliminary 顶针板Ejector Plate 名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Slide Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft 顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Noozzle Bulishing水口板导套Runner Stripper Pin定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel外廊Contour 吊环Safety Hoist Ring落单会议Kick-off 日期印Dating Insert装卸孔Handing Hole 环保印Recycling Insert运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙导柱位Leader Pin Location产品名Part Name缩水Shrinkage下模镶件Core Block小镶件Sub-Insert上模小镶件Core Sub-Insert行位镶件Slide Insert压紧块（铲机）Jaw硬片（摩擦片）Wear Plate 气顶Air Poppet Valve 截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品编号Part No版本Rev上模镶件Cavity Block下模小镶件Core Sub-Insert行位Slide压条Gib扁顶Blade出模斜波Draft水口铁Runner Bar 手动滑块模具Hand Slide-In Type Mold上模水口铁Upper Runner Bar 回针板Backup下模水口铁Lower Runner Bar 合模Shutoff弹簧Spring水口钩针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Inter Lock锁模板Safty Bar‘O’令（密封圈）O’Ring喉塞Plug隔水片Baffrle波子螺丝（行为定位螺丝）斜顶Lifter控制开关Switch 空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑料模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer烙接线（夹水纹）Weldlin吸针Sucker Pin回针板Retainer Plate顶出板Knock-Out Plate回针Return Pin 电动安全开关Electrical-Safety Switch斜导柱Angle Pin 脱开Cut Of Position推板Stripper Plate 预先决定PreloadA’板A’PlateB’板B’Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate精磨Finished通框Through Window粘后模Stricking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling 缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib有托顶针Shoulder Ejector Pin顶针板导套Guided Ejector Bushing 针板导柱Guided Ejector Leader Pin 不干胶Adhesive Sticker线切割Wire-Cut电火花Edm抛光Polishing走不齐Short Shot 蚀纹Texture挂成品Part Hanging 探热针Thermocouple漏水Water Leakage 三打螺丝毫（限螺丝）Stripper Bolt刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling倒圆Fillet顶棍Ejector顶白Stress Mark名称块表Title Block版本标识Revision Level材料清单Stock List 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料Cold Slag压力Pressure 螺纹孔Tapping Hole 连接件Fitting粘前模Sticking Cav 替换镶件Interchangeable Mold Insert制定吨位的注塑机Specific Press水嘴接头Water Fitting斜导柱（斜边）Angle Pin 螺纹Eyebolt Thread分模面Parting Surface 倒扣Under-Cut披峰Flash 锁定位Lock缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive热流道Manifold型腔数Cav No模号Mold No回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint 楔子（铲机）Wedge高产量模量High Volume Running Mold剖面图Cross Section模具结构Mold Construction出模角Draft擦位Shut-Off(S/O)导套Bushing导向针Guide Pin胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave托司Pin。

密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边 L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity in
加硬 Hapden 唧嘴 Sprue 设计筒图 Design Preliminary 名称块表 Title Block 版本标识 Revision Level 材料清单 Stock List 制模 Build Mold 手动滑块 Hand Slide 漏水测试 Leak Test 流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action
针板导柱 Guided Ejection Leader Pin
唧 嘴 Sprue Bushing
三板模延伸式唧嘴 Extension Nozzle Bushing
水口板导套
Runner Stripper Plate Bushing
定位圈（法兰）
Locating Ring
管钉（定位销）
Dowel Pin
模具常用术语中英文对照
中文
英文
回针

模芯 Parting Core 耐落胶 Teflon Paste局部视图 Partial View 偏移量 Offset冷料 Cold Slag 水塞 Water Line Plug线切割 Wire 撬模脚 Ppy Slot轮廓 Contour 重新加工 Reworked螺纹孔Tapping Hole 配件 Components连接件 Fittings 补偿 Compensation斜针 Angle Pin 平面度 Parallel接合 Engage 倒角Chamfer替换镶件Interchangeable Mold Inserts 模胚 Mold Base指定吨位的注塑机 Specific Press 热嘴Hotnozzle水嘴接头 Water Fitting 火花机 Edm螺纹 Eyebolt Thread 熔接线 Weildline回针 Stop Pin 压机 Press二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing镶件 Mold Insert 梯形 Trapezoid加硬 Harden 凸缘、法兰 Flange唧嘴 Sprue 方铁 Spacer Block设计筒图 Design Preliminary 顶针板 Ejector Plate名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate材料清单 Stock List 后模镶针 Core Pin制模 Build Mold 垃圾钉 Stop Pin手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing加强筋 Reinforcing 水口板导套 Runner Stripper Pin三角撑 Gusset 定位圈法兰Locating Ring柱子 Bossed 管钉定位销Dowel Pin出模斜度 Draft 管状管钉 Tubular Dowel外廊 Contour 吊环 Safety Hoist Ring落单会议 Kick-off 日期印 Dating Insert装卸孔 Handing Hole 环保印 Recycling Insert运输安全带 Moldstrap 气顶Air Poppet Valve码模槽 Clamp Slot 截水口镶件 Runner Shut-Off Insert撑头 Support Pillar 早回 Early Ejector Return螺牙1/2-13 Eye 1/2-13Tap 加速项 Accelerated Ejector导柱位 Leader Pin Location 客户 Client产品名 Part Name 产品编号 Part No缩水 Shrinkage 版本Rev下模镶件Core Block 上模镶件Cavity Block小镶件 Sub-Insert 下模小镶件Core Sub-Insert上模小镶件 Core Sub-Insert 行位 Slide行位镶件 Slide Insert 压条 Gib压紧块铲机 Jaw 扁顶 Blade硬片摩擦片Wear Plate 出模斜波 Draft水口铁 Runner Bar 手动滑块模具 Hand Slide-In Type Mold上模水口铁 Upper Runner Bar 回针板 Backup下模水口铁 Lower Runner Bar 合模 Shutoff弹簧 Spring 空隙槽 Clearance Slot水口钩针 Sprue Puller Pin 导柱及导套 Leader Pin Bushing 顶针 Ejector Pin 水口拉钩 Spuer Puller撑头 Support Pillar 模框镶件 Pocket Insert直身锁 Side Lock 成型热固性塑料模具 Thermoset Mold 斜度锁 Inter Lock 三板模 3-Plat Mold锁模板 Safty Bar 分型面 Parting Line‘O’令密封圈O’Ring 司筒 Ejector Sleeve喉塞 Plug 垫圈 Washer隔水片 Baffrle 烙接线夹水纹Weldlin波子螺丝行为定位螺丝吸针 Sucker Pin斜顶 Lifter 回针板 Retainer Plate控制开关 Switch 顶出板 Knock-Out Plate回针 Return Pin 电动安全开关 Electrical-Safety Switch斜导柱 Angle Pin 脱开 Cut Of Position推板 Stripper Plate 预先决定 PreloadA’板 A’Plate 缓冲器 BumperB’板 B’Plate 衬垫 Cushion方铁垫铁Spacer Block 公差 Tolerance顶针板 Ejector Plate 突然性动作 Slam顶针底板 Ejector Retainer Plate 销针 Dowel垫板 Retainer Plate 钩槽 Gib精磨 Finished 有托顶针 Shoulder Ejector Pin通框 Through Window 顶针板导套 Guided Ejector Bushing 粘后模 Stricking Core 针板导柱 Guided Ejector Leader Pin粘水口 Sticking Sprue 不干胶 Adhesive Sticker夹水纹 Weld Line 线切割Wire-Cut变形 Warpage 电火花 Edm走水不平均 Filling 抛光 Polishing走不齐 Short Shot 蚀纹 Texture挂成品 Part Hanging 探热针 Thermocouple漏水 Water Leakage 三打螺丝毫限螺丝 Stripper Bolt 刮花擦伤 Galling 盖板 Cover Plate漏电 Ele Leakage 齿轮 Gear困气 Air Trapping 油唧 Hydraulic Cylinder温度 Temperature 司筒 Ejector Sleeve注塑模 Injection Mold 导柱 Leader Pin入水 Gate 冷料 Cold Slag试板 Sampling 压力 Pressure 倒圆 Fillet 螺纹孔 Tapping Hole顶棍 Ejector 连接件 Fitting顶白 Stress Mark 粘前模 Sticking Cav 名称块表 Title Block 替换镶件 Interchangeable MoldInsert版本标识 Revision Level 制定吨位的注塑机 Specific Press材料清单 Stock List 水嘴接头 Water Fitting斜导柱斜边Angle Pin 螺纹 Eyebolt Thread分模面 Parting Surface 倒扣 Under-Cut披峰 Flash 锁定位 Lock缩水 Sink Mark 楔子铲机Wedge氮化 Nitride 高产量模量 High Volume RunningMold不规则四边形 Trapezoid 剖面图 Cross Section缩水 Shrinkage 模具结构 Mold Construction连续的 Consecutive 出模角Draft热流道 Manifold 擦位 Shut-OffS/O型腔数 Cav No 导套 Bushing模号 Mold No 导向针Guide Pin回针 Return Pin 胶料Material加硬 Harden 尺寸 Dimension唧嘴 Sprue 重要尺寸 Critical Dimension 设计筒图 Design Preliminary 雕刻 Engrave丝印 Silkprint 托司 Pin。

模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。

压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。

气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。

流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。