MAA50-1S12SBN中文资料

SA5.0A - SA170A Series 500 Watt Peak Power MiniMOSORB t Zener Transient Voltage Suppressors Unidirectional*The SA5.0A series is designed to protect voltage sensitive components from high voltage, high energy transients. They haveexcellent clamping capability, high surge capability, low zener impedance and fast response time. The SA5.0A series is supplied in ON Semiconductor’s exclusive, cost-effective, highly reliable Surmetic t axial leaded package and is ideally-suited for use in communication systems, numerical controls, process controls, medical equipment, business machines, power supplies and many other industrial/consumer applications.Specification Features:•Working Peak Reverse V oltage Range – 5 to 170 V•Peak Power – 500 Watts @ 1 ms•ESD Rating of Class 3 (>16 KV) per Human Body Model •Maximum Clamp V oltage @ Peak Pulse Current•Low Leakage < 1 µA above 8.5 V•UL 497B for Isolated Loop Circuit Protection•Maximum Temperature Coefficient Specified•Response Time is typically < 1 nsMechanical Characteristics:CASE:V oid-free, Transfer-molded, Thermosetting plastic FINISH:All external surfaces are corrosion resistant and leads are readily solderableMAXIMUM LEAD TEMPERATURE FOR SOLDERING:230_C,1/16″ from the case for 10 secondsPOLARITY:Cathode indicated by polarity band.MOUNTING POSITION:AnyMAXIMUM RATINGSA Figure 2.2.1/2 sine wave (or equivalent square wave), PW = 8.3 ms, duty cycle = 4 pulsesper minute*Please see SA5.0CA – SA170CA for Bidirectional devices.Device Package ShippingORDERING INFORMATION SAxxxA Axial Lead1000 Units/BoxSAxxxARL Axial Lead5000/T ape & ReelDevices listed in bold, italic are ON Semiconductor Preferred devices. Preferred devices are recommended choices for future use and best overall value.ELECTRICAL CHARACTERISTICS (T A = 25°C unlessotherwise noted, V= 3.5 V Max. @ I (Note 6.) = 35 A)ELECTRICAL CHARACTERISTICS (T= 25°C unless otherwise noted, V = 3.5 V Max. @ I (Note 6.)= 35 A)3.MiniMOSORB t transients suppressor is normally selected according to the maximum working peak reverse voltage (V RWM), whichshould be equal to or greater than the dc or continuous peak operating voltage level.4.V BR measured at pulse test current I T at an ambient temperature of 25°C.5.Surge current waveform per Figure 4 and derate per Figures 1 and 2.6.Square waveform, PW = 5.3 ms, Non–repetitive duty cycle.ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted, V = 3.5 V Max. @ I (Note 6.)= 35 A)NOTES:3.MiniMOSORB t transients suppressor is normally selected according to the maximum working peak reverse voltage (V RWM), whichshould be equal to or greater than the dc or continuous peak operating voltage level.4.V BR measured at pulse test current I T at an ambient temperature of 25°C.5.Surge current waveform per Figure 4 and derate per Figures 1 and 2.6.Square waveform, PW = 5.3 ms, Non–repetitive duty cycle.1001010.11ms 10msP P , P E A K P O W E R (k W )t p , PULSE WIDTHFigure 1. Pulse Rating Curve 1008060402000255075100125150175200P E A K P U L S E D E R A T I N G I N % O F P E A K P O W E R O R C U R R E N T @ T A = 25C T A , AMBIENT TEMPERATURE (_C)Figure 2. Pulse Derating Curve10,0001000C, C A P A C I T A N C E (p F )V BR , BREAKDOWN VOLTAGE (VOLTS)Figure 3. Capacitance versus Breakdown Voltage t, TIME (ms)Figure 4. Pulse Waveform543210P D , S T E A D Y S T A T E P O W E R D I S S I P A T I O N (W A T T S )T L , LEAD TEMPERATURE (_C)Figure 5. Steady State Power DeratingK _UL RECOGNITION*The entire series including the bidirectional CA suffix has Underwriters Laboratory Recognition for the classification of protectors (QVGV2) under the UL standard for safety 497B and File #E 116110. Many competitors only have one or two devices recognized or have recognition in a non-protective category. Some competitors have no recognition at all. With the UL497B recognition, our parts successfully passed several tests including Strike V oltage Breakdown test, Endurance Conditioning, Temperature test, Dielectric V oltage-Withstand test, Discharge test and several more.Whereas, some competitors have only passed a flammability test for the package material, we have been recognized for much more to be included in their protector category.*Applies to SA5.0A, CA – SA170A, CA.OUTLINE DIMENSIONSTransient Voltage Suppressors – Axial Leaded 500 Watt Peak Power MiniMOSORB™MINI MOSORBNotesMiniMOSORB and Surmetic are trademarks of Semiconductor Components Industries, LLC.ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATIONCENTRAL/SOUTH AMERICA:Spanish Phone:303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)Email:ONlit–spanish@Toll–Free from Mexico: Dial 01–800–288–2872 for Access –then Dial 866–297–9322ASIA/PACIFIC: LDC for ON Semiconductor – Asia SupportPhone:303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)Toll Free from Hong Kong & Singapore:001–800–4422–3781Email: ONlit–asia@JAPAN: ON Semiconductor, Japan Customer Focus Center4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031Phone: 81–3–5740–2700。

LM78M12中⽂资料LM341/LM78MXX Series3-Terminal Positive Voltage RegulatorsGeneral DescriptionThe LM341and LM78MXX series of three-terminal positive voltage regulators employ built-in current limiting,thermal shutdown,and safe-operating area protection which makes them virtually immune to damage from output overloads.With adequate heatsinking,they can deliver in excess of 0.5A output current.Typical applications would include local (on-card)regulators which can eliminate the noise and de-graded performance associated with single-point regulation.Featuresn Output current in excess of 0.5A n No external componentsn Internal thermal overload protection n Internal short circuit current-limitingn Output transistor safe-area compensationnAvailable in TO-220,TO-39,and TO-252D-PAK packagesn Output voltages of 5V,12V,and 15VConnection DiagramsTO-39Metal Can Package (H)DS010484-5Bottom ViewOrder Number LM78M05CH,LM78M12CH or LM78M15CHSee NS Package Number H03ATO-220Power Package (T)DS010484-6Top ViewOrder Number LM341T-5.0,LM341T-12,LM341T-15,LM78M05CT,LM78M12CT or LM78M15CTSee NS Package Number T03BTO-252DS010484-19Top ViewOrder Number LM78M05CDT See NS Package Number TD03BJuly 1999LM341/LM78MXX Series 3-Terminal Positive Voltage Regulators1999National Semiconductor Corporation /doc/96ef4d46852458fb770b5641.htmlAbsolute Maximum Ratings(Note1)If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.Lead Temperature(Soldering,10seconds)TO-39Package(H)300?C TO-220Package(T)260?C Storage Temperature Range?65?C to+150?C Operating Junction TemperatureRange?40?C to+125?C Power Dissipation(Note2)Internally Limited Input Voltage5V≤V O≤15V35V ESD Susceptibility TBDElectrical CharacteristicsLimits in standard typeface are for T J=25?C,and limits in boldface type apply over the?40?C to+125?C operating temperature range.Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control(SQC) methods.LM341-5.0,LM78M05CUnless otherwise specified:V IN=10V,C IN=0.33µF,C O=0.1µFSymbol Parameter Conditions Min Typ Max Units V O Output Voltage I L=500mA 4.8 5.0 5.2V5mA≤I L≤500mA 4.75 5.0 5.25P D≤7.5W,7.5V≤V IN≤20VV R LINE Line Regulation7.2V≤V IN≤25V I L=100mA50mVI L=500mA100V R LOAD Load Regulation5mA≤I L≤500mA100I Q Quiescent Current I L=500mA410.0mA ?I Q Quiescent Current Change5mA≤I L≤500mA0.57.5V≤V IN≤25V,I L=500mA 1.0V n Output Noise Voltage f=10Hz to100kHz40µVElectrical CharacteristicsLimits in standard typeface are for T J=25?C,and limits in boldface type apply over the?40?C to+125?C operating temperature range.Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control(SQC) methods.(Continued)LM341-12,LM78M12CUnless otherwise specified:V IN=19V,C IN=0.33µF,C O=0.1µFSymbol Parameter Conditions Min Typ Max UnitsV O Output Voltage I L=500mA11.51212.5V5mA≤I L≤500mA11.41212.6P D≤7.5W,14.8V≤V IN≤27VV R LINE Line Regulation14.5V≤V IN≤30V I L=100mA120mVI L=500mA240V R LOAD Load Regulation5mA≤I L≤500mA240I Q Quiescent Current I L=500mA410.0mAI Q Quiescent Current Change5mA≤I L≤500mA0.514.8V≤V IN≤30V,I L=500mA 1.0V n Output Noise Voltage f=10Hz to100kHz75µVRipple Rejection f=120Hz,I L=500mA69dBV IN Input Voltage Required I L=500mA17.6V to Maintain Line RegulationV O Long Term Stability I L=500mA60mV/khrs Note1:Absolute maximum ratings indicate limits beyond which damage to the component may occur.Electrical specifications do not apply when operating the de-vice outside of its rated operating conditions.Note2:The typical thermal resistance of the three package types is:T(TO-220)package:θ(JA)=60?C/W,θ(JC)=5?C/WH(TO-39)package:θ(JA)=120?C/W,θ(JC)=18?C/WDT(TO-252)package:θ(JA)=92?C/W,θ(JC)=10?C/W3/doc/96ef4d46852458fb770b5641.htmlSchematic DiagramDS010484-1 /doc/96ef4d46852458fb770b5641.html 4 Typical Performance CharacteristicsPeak Output CurrentDS010484-10Ripple RejectionDS010484-11Ripple RejectionDS010484-12Dropout VoltageDS010484-13Output Voltage(Normalizedto1V at T J=25?C)DS010484-14Quiescent CurrentDS010484-15/doc/96ef4d46852458fb770b5641.html 5Typical Performance Characteristics(Continued)Design ConsiderationsThe LM78MXX/LM341XX fixed voltage regulator series has built-in thermal overload protection which prevents the de-vice from being damaged due to excessive junction tem-perature.The regulators also contain internal short-circuit protection which limits the maximum output current,and safe-area pro-tection for the pass transistor which reduces the short-circuit current as the voltage across the pass transistor is in-creased.Although the internal power dissipation is automatically lim-ited,the maximum junction temperature of the device must be kept below +125?C in order to meet data sheet specifica-tions.An adequate heatsink should be provided to assure this limit is not exceeded under worst-case operating condi-tions (maximum input voltage and load current)if reliable performance is to be obtained).1.0Heatsink ConsiderationsWhen an integrated circuit operates with appreciable cur-rent,its junction temperature is elevated.It is important to quantify its thermal limits in order to achieve acceptable per-formance and reliability.This limit is determined by summing the individual parts consisting of a series of temperature rises from the semiconductor junction to the operating envi-ronment.A one-dimension steady-state model of conduction heat transfer is demonstrated in The heat generated at thedevice junction flows through the die to the die attach pad,through the lead frame to the surrounding case material,to the printed circuit board,and eventually to the ambient envi-ronment.Below is a list of variables that may affect the ther-mal resistance and in turn the need for a heatsink.R θJC (Component Variables)R θCA (Application Variables)Leadframe Size &Material Mounting Pad Size,Material,&LocationNo.of Conduction Pins Placement of Mounting Pad Die SizePCB Size &Material Die Attach MaterialTraces Length &WidthMolding Compound Size and MaterialAdjacent Heat Sources Volume of Air Air FlowAmbient Temperature Shape of Mounting PadQuiescent CurrentDS010484-16Output ImpedanceDS010484-17Line Transient Response DS010484-7Load Transient ResponseDS010484-8/doc/96ef4d46852458fb770b5641.html6Design Considerations(Continued)The LM78MXX/LM341XX regulators have internal thermal shutdown to protect the device from over-heating.Under all possible operating conditions,the junction temperature of the LM78MXX/LM341XX must be within the range of 0?C to 125?C.A heatsink may be required depending on the maxi-mum power dissipation and maximum ambient temperature of the application.To determine if a heatsink is needed,the power dissipated by the regulator,P D ,must be calculated:I IN =I L +I GP D =(V IN ?V OUT )I L +V IN I Gshows the voltages and currents which are present in the circuit.The next parameter which must be calculated is the maxi-mum allowable temperature rise,T R (max):θJA =TR (max)/P D If the maximum allowable value for θJA ?C/w is found to be ≥60?C/W for TO-220package or ≥92?C/W for TO-252pack-age,no heatsink is needed since the package alone will dis-sipate enough heat to satisfy these requirements.If the cal-culated value for θJA fall below these limits,a heatsink is required.As a design aid,Table 1shows the value of the θJA of TO-252for different heatsink area.The copper patterns that we used to measure these θJA are shown at the end of the Application Note Section.reflects the same test results as what are in the Table 1shows the maximum allowable power dissipation vs.ambi-ent temperature for theTO-252device.shows the maximum allowable power dissipation vs.copper area (in 2)for the TO-252device.Please see AN1028for power enhancement techniques to be used with TO-252package.TABLE 1.θJA Different Heatsink AreaLayoutCopper AreaThermal Resistance Top Sice (in 2)*Bottom Side (in 2)(θJA ,?C/W)TO-25210.0123010320.06608730.306040.5305450.7605261047700.284800.470900.6631000.857110157120.0660.06689130.1750.17572140.2840.28461150.3920.39255160.50.553*Tab of device attached to topside copperDS010484-23FIGURE 1.Cross-sectional view of Integrated Circuit Mounted on a printed circuit board.Note that the case temperature is measured at the point where the leadscontact with the mounting pad surface DS010484-24FIGURE 2.Power Dissipation Diagram/doc/96ef4d46852458fb770b5641.html 7Design Considerations(Continued)Typical ApplicationDS010484-20FIGURE 3.θJA vs.2oz Copper Area for TO-252DS010484-22FIGURE 4.Maximum Allowable Power Dissipation vs.Ambient Temperature for TO-252DS010484-21FIGURE 5.Maximum Allowable Power Dissipation vs.2oz.Copper Area for TO-252DS010484-9*Required if regulator input is more than 4inches from input filter capacitor (or if no input filter capacitor is used).**Optional for improved transient response./doc/96ef4d46852458fb770b5641.html 8 Physical Dimensions inches(millimeters)unless otherwise notedTO-39Metal Can Package(H)Order Number LM78M05CH,LM78M12CH or LM78M15CHNS Package Number H03A9/doc/96ef4d46852458fb770b5641.htmlPhysical Dimensions inches(millimeters)unless otherwise noted(Continued)TO-220Power Package(T)Order Number LM341T-5.0,LM341T-12,LM341T-15,LM78M05CT,LM78M12CT or LM78M15CT NS Package Number T03B/doc/96ef4d46852458fb770b5641.html 10Physical Dimensionsinches (millimeters)unless otherwise noted (Continued)LIFE SUPPORT POLICYNATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION.As used herein:1.Life support devices or systems are devices or systems which,(a)are intended for surgical implant into the body,or (b)support or sustain life,and whose failure to perform when properly used in accordance with instructions for use provided in the labeling,can be reasonably expected to result in a significant injury to the user.2.A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system,or to affect its safety or effectiveness.National Semiconductor Corporation AmericasTel:1-800-272-9959Fax:1-800-737-7018Email:support@/doc/96ef4d46852458fb770b5641.htmlNational Semiconductor EuropeFax:+49(0)180-5308586Email:europe.support@/doc/96ef4d46852458fb770b5641.htmlDeutsch Tel:+49(0)180-5308585English Tel:+49(0)180-5327832Fran?ais Tel:+49(0)180-5329358Italiano Tel:+49(0)180-5341680National Semiconductor Asia Pacific Customer Response Group Tel:65-2544466Fax:65-2504466Email:sea.support@/doc/96ef4d46852458fb770b5641.htmlNational Semiconductor Japan Ltd.Tel:81-3-5639-7560Fax:81-3-5639-7507/doc/96ef4d46852458fb770b5641.htmlTO-252Order Number LM78M05CDT NS Package Number TD03BLM341/LM78MXX Series 3-Terminal Positive Voltage RegulatorsNational does not assume any responsibility for use of any circuitry described,no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry andspecifications.。

INSULATED PACKAGEConditionParameterSymbol V CES ±I C ±I CP P C T jCollector-Emitter Voltage Collector CurrentCollector Current (Peak)Collector Dissipation Junction TemperatureV D = 15V, V CIN = 15V T C = 25°C T C = 25°C T C = 25°CV A A W °CMAXIMUM RATINGS (Tj = 25°C, unless otherwise noted)INVERTER PARTSymbol ParameterConditionRatings Unit 120050100338–20 ~ +150INTERNAL FUNCTIONS BLOCK DIAGRAMV CES I C I CP P CV R(DC)I F T jBRAKE PARTCollector-Emitter Voltage Collector CurrentCollector Current (Peak)Collector DissipationFWDi Rated DC Reverse Voltage FWDi Forward Current Junction TemperatureV D = 15V, V CIN = 15V T C = 25°C T C = 25°C T C = 25°C T C = 25°C T C = 25°CV A A W V A °CSymbol ParameterConditionRatings Unit 12001530134120015–20 ~ +150V FO I FOCONTROL PARTV mA2020Supply Voltage Input VoltageFault Output Supply Voltage Fault Output CurrentRatings Unit Applied between :V UP1-V UPCV VP1-V VPC , V WP1-V WPC , V N1-V NCApplied between :U P -V UPC , V P -V VPCW P -V WPC , U N • V N • W N • B r -V NCApplied between :U FO -V UPC, V FO-V VPC, W FO -V WPCF O -V NCSink current at U FO , V FO , W FO and F O terminal2020V D V CIN V V GND GND SiOutIn F O V CCGND GND SiOutIn F O V CC GND GND SiOutIn F O V CCGND GND SiOutIn F O V CCF O Br V NC W NV NU NV N1PU V W N B TEMPV WPC W P V WP1GND In V CCGND Si OUTW FO F OV VPC V P V VP1GND In V CCGND Si OUTV FO F OV UPC U P V UP1GND In V CCGND Si OUTU FOF ORfoRfoRfoRfoR fo = 1.5k ΩINSULATED PACKAGETOTAL SYSTEM3.303.353.52.30.31.03.41.2110Min.Typ.Max.Collector-Emitter Saturation Voltage Collector-Emitter Cutoff Current–I C = 50A, V D = 15V, V CIN = 15V T j = 25°C T j = 125°C ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)INVERTER PARTParameterSymbol Test ConditionV CE(sat)I CESV EC t on t rr t c(on)t off t c(off)Limits ———0.4——————2.652.752.50.90.20.42.40.7——T j = 25°C T j = 125°CFWDi Forward VoltageSwitching TimeV D = 15V, V CIN = 0V ↔15V V CC = 600V, I C = 50A T j = 125°CInductive Load (upper and lower arm)V CE = V CES , V CIN = 15VV D = 15V, I C =50A V CIN = 0VV mAVµsUnit ParameterSymbolSupply Voltage Protected bySCSupply Voltage (Surge)Module Case OperatingTemperatureStorage Temperature Isolation Voltage ConditionV CC(surge)T CT stgV iso Ratings V CC(PROT)8001000–20 ~ +100–40 ~ +1252500Unit V °C °C V rmsV V D = 13.5 ~ 16.5V, Inverter Part,T j = 125°C StartApplied between : P-N, Surge value or without switching(Note-1)60Hz, Sinusoidal, Charged part to Base, AC 1 min.—————V CE(sat)I CESV FM V mAMin.Typ.Max.V Collector-Emitter Saturation Voltage FWDi Forward Voltage Collector-Emitter Cutoff CurrentI F = 15AT j = 25°C T j = 125°CUnit ParameterSymbol Test ConditionLimits 3.303.203.501102.502.202.50——T j = 25°C T j = 125°C BRAKE PARTV D = 15V, I C = 15A V CIN = 0V V CE = V CES , V CIN = 15V(Note-1)T C measurement point is below. (3mm depth at the center of the side of base plate)TcINSULATED PACKAGE3.53.5————Mounting part screw : M5Main terminalscrew : M5—Symbol ParameterMounting torque Mounting torque WeightTest ConditionUnit N • m N • m gLimits Min.Typ.Max.2.52.5—3.03.0560MECHANICAL RATINGS AND CHARACTERISTICS(Note-2)Fault output is given only when the internal SC, OT & UV protection.Fault output of OT protection operate by lower arm.Fault output of OT, UV protection given pulse while over level.V D = 15VBase-plateTemperature detection, V D = 15V –20 ≤ T j ≤ 125°C V D = 15V, V FO = 15V (Note-2)V D = 15V(Note-2)Trip level Reset level Trip level Reset levelCircuit CurrentInput ON Threshold Voltage Input OFF Threshold Voltage Over Current Trip Level Short Circuit Trip Level Over Current Delay Time Short Circuit Current Delay TimeOver Temperature Protection Supply Circuit Under-Voltage ProtectionFault Output Current Minimum Fault Output Pulse WidthV th(ON)V th(OFF)OC SC t off(OC)t off(SC)OT OT r UV UV r I FO(H)I FO(L)t FO–20 ≤ T j ≤ 125°C, V D = 15V, Break part –20≤ T j ≤ 125°C, V D = 15V V D = 15V, Break part Inverter part Brake partCONTROL PARTI D ParameterSymbol µs °C V mA ms60181.82.3—————125—12.5—0.0115—mA ——1.21.72259———111—11.5———1.0Max.Min.Typ.Unit Limits 44131.52.0——52101011810012.012.5—101.8V µs A A V D = 15V, V CIN = 15VApplied between :U P -V UPC , V P -V VPC , W P -V WPCU N • V N • W N • B r -V NC Test ConditionV N1-V NC V *P1-V *PCR th(j-c)Q R th(j-c)F R th(j-c)Q R th(j-c)F R th(c-f)Symbol THERMAL RESISTANCES0.370.700.931.500.027°C/WInverter IGBT part (per 1/6 module)Inverter FWDi part (per 1/6 module)Brake IGBT part Brake FWDi partCase to fin, Thermal grease applied (per 1 module)ParameterTest ConditionUnitLimits Min.Typ.Max.——————————Junction to case Thermal ResistancesContact Thermal ResistanceRECOMMENDED CONDITIONS FOR USERecommended valueUnit Test ConditionSymbol ParameterV Applied across P-N terminalsApplied between :V UP1-V UPC , V VP1-V VPCV WP1-V WPC , V N1-V NC (Note-3)Applied between :U P -V UPC , V P -V VPC , W P -V WPCU N • V N • W N • B r -V NC For IPM’s each input signalsUsing Application Circuit input signal of IPM,Sinusoidal PWM VVVF inverterSupply Voltage Control Supply Voltage Input ON Voltage Input OFF Voltage Arm Shoot-through Blocking Time PWM Input Frequency≤ 80015±1.5≤ 0.8≥ 4.0≥ 3.0≤ 20V CC V CIN(ON)V CIN(OFF)t dead f PWMV D V µs kHzV (Note-3)With ripple satisfying the following conditions dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peakINSULATED PACKAGEINSULATED PACKAGEINSULATED PACKAGE。