Chapter_01_lecture

16.0 ReleaseLecture 1Introduction to ANSYS WorkbenchIntroduction to ANSYS MechanicalWelcome!Welcome to the ANSYS Mechanical application introductory training course.This training course covers the basics of using ANSYS Mechanicalin performing structural and thermal analyses.It is intended for all new or occasional ANSYS Mechanical users, regardlessof the CAD software used.Course Objectives:–General understanding of the user interface, as related to geometry import, meshing, application of loads and supports, and postprocessing–Procedure for performing FEA simulations, including linear static, modal, and harmonic structural analyses and nonlinear steady-state thermal analyses–Utilizing parameters for ‘what-if’ scenarios•Training Courses are also available covering the use of other Workbench modules(e.g. DesignModeler,Design Exploration, etc.) .Morning Lecture – IntroductionLecture – Chapter 2: Mechanical BasicsWorkshop 2.1Lecture – Chapter 3: General PreprocessingWorkshop 3.1Lecture – Chapter 3, continued Afternoon Workshop 3.2Lecture – Chapter 3, continuedWorkshop 3.3 or Workshop 3.4Lecture – Chapter 4: Meshing in MechanicalWorkshop 4.1Lecture – Chapter 4 (continued)Workshop 4.2Lecture – Chapter 5: Modeling ConnectionsWorkshop 5.1Morning Lecture – Chapter 5 (continued)Workshop 5.2Lecture – Chapter 6: Remote Boundary ConditionsWorkshop 6.1Lecture – Chapter 6 (continued)Workshop 6.2Lecture – Chapter 7: Static Structural AnalysisWorkshop 7.1Afternoon Lecture – Chapter 7 (continued)Workshop 7.2Lecture – Chapter 8: Modal AnalysisWorkshop 8.1Lecture – Chapter 9: Thermal AnalysisWorkshop 9.1Morning Lecture – Chapter 10: Multistep AnalysisWorkshop 10.1Lecture – Chapter 11: Results and PostprocessingWorkshop 11.1Afternoon Lecture – Chapter 12: CAD and ParametersWorkshop 12.1Choice of Appendix Chapters or discussion of user issues** This course has been designed to run to just over 2.5 days to allow the last afternoon to be more informal. There is a choice of Appendix Chapters that explore different analysis types or go into some subjects in more depth. If time allows user problems can also be discussed depending on the number of attendees.Lecture 1: ContentsA.About ANSYS Inc.B.ANSYS Customer PortalC.ANSYS Workbench OverviewD.DemonstrationE.SummaryF.Overview of MechanicalG.APPENDIXA: About ANSYS Inc.FOCUSEDThis is all we do.Leading product technologies in all physics areas Largest development team focused on simulationDEDICATED 2,700+7540employeeslocationscountriesMARKET LEADERLong-term growth, financial stability and CAD agnosticPROVENValidating our solutions on themost advanced product applications40+ yearsBreadth of TechnologiesStructural Mechanics: From Linear Statics Fluid Mechanics:From Single-Phase Flows Electromagnetics: From Low-Frequency Windings Systems:From Data SharingTo High-Speed ImpactTo Multiphase CombustionTo High-Frequency Field AnalysisTo Multi-Domain System AnalysisThe ANSYS Customer PortalContains over 85,000 support assets powered by a modern web user interface and powerful search engine.Over 5.2 million page views in 2014SupportProductsDownloadsKnowledge ResourcesClassroom Training WebinarsService RequestsProduct AssetsLatest Release Updates ToolsPrevious Release(s) Extension Library (AppStore)SolutionsConference Proceedings Class3 Reports Documentation Training & Tutorialshttps://About searchThe ANSYS Customer Portal’s search is powered bydedicated Google® hardware.Mesh = Meshed = MeshingExport = Exported = ExportingXXXXX = YYYYY = ZZZZZExample:You want a meshing tutorial for ANSYS Meshing and your search has results for other products that are not of interest to you; by selecting the product facet “ANSYS Meshing” you can narrow down your results further.Support / downloads / trainingSubmit and review service requestsIf you cannot find the answer to your question within the ANSYS Customer Portal then you can submit a service request. A member of ANSYS technical support will then get back toyou with advice or a solution.Download the latest software and updatesDownload ISO images if you wish to create a DVD which is recommend for installations onmultiple computers and allows you to keep an archive of the installation for later re-use.Package downloads can also be selected if you want to install files directly.Download classroom and video training materialTraining and tutorial material are available for both a broad range of ANSYS products anduser’s experience. Search the hundreds of courses available and improve your knowledgeof ANSYS software.C. ANSYS WorkbenchANSYS Workbench is a project-management tool. It can be considered as the top-level interface linking all our software tools.Workbench handles the passing of data between ANSYS Geometry / Mesh / Solver / Postprocessing tools.This greatly helps project management. You do not need worry about the individual files on disk (geometry, mesh etc). Graphically, you can see at-a-glance how a project has been built. Because Workbench can manage theindividual applications AND pass databetween them, it is easy to automaticallyperform design studies (parametricanalyses) for design optimisation.D. DemonstrationDemonstration : 01_WB_Presentation.mp4 •What you can learn in this demonstration :–How to use Workbench project page–How to save, open, archive a project–How to create different analysis–Understand each stage of an analysis–Edit units, properties and files options–Working with parametersE: SummaryANSYS Workbench is a convenient way of managing your simulation projects.Workbench is used to launch the individual software components, and used to transfer data between them.It is easy to see at-a-glace how a model has been built, and determine which files were used for a particular simulation (pairing geometry files to solver runs)Workbench also makes it straightforward to perform parametric analyses (without the user needing to manually launch each application in turn), and makes it easy to simulate multi-physics scenarios like fluid-structure interaction.F. Mechanical OverviewAnalysis types available in Workbench - Mechanical:†•Structural (static and transient):–Linear and nonlinear structural analyses.•Dynamics:–modal, harmonic, response spectrum, random vibration, flexible and rigid dynamics.•Heat Transfer (steady state and transient):–Solve for temperature field and heat flux. Temperature-dependent conductivity, convection, radiation and materials allowed.•Magnetostatic:–Perform various magnetic field analyses.•Electrical:–Simulate electrical devices such as motors, solenoids, etc..† Note, the active ANSYS license dictates what functionality is available to the user. Not all features listed are covered in this Introductory course.… Mechanical OverviewAdd-on licenses for Mechanical:•Rigid Dynamics•Fatigue Module•ACP16.0 Workbench products are available for Windows and Linux operating systems. •Check the ANSYS web site or online documentation for the latest compatibilities.Network licensing capabilities are used for all ANSYS and ANSYS Workbench products.G. APPENDIX. . . Workbench OverviewThe options visible in the left-hand column show all the products (systems) you have licenses for.TIP: If this list appears empty, you have a problem with your licensing. “Analysis Systems” are ready-made stencils that include all the individual systems (applications) needed for common analyses (for example Geometry + Mesh + Solver + Post-Processor) “Component Systems” are the individual building-blocks for each stage of the analysis“Design Exploration” provides tools for optimising designs and understanding the parametric response.. . . Basic WorkflowDragging an Analysis System ontothe project desktop lays out aworkflow, comprising all the stepsneeded for a typical analysis.Workflow is from top to bottom.As each stage is complete, the iconat the right-hand side changes. . . Alternative WorkflowHowever, an analysis could equally well be prepared by selecting theindividual Component Systems that are needed for this analysis, and thenlinking them together with connectors.TIP: There are two ways to create the connectors between the systems:1)Use the mouse to draw a line (eg A2 to B3, B4 to C4 etc)2)Or, simply drop the new system on the cell of the upstream one, and thelink will be generated automatically.. . . Cell StatesAs each stage in the model-build is completed, the state of thecell changes.Status after creating Geometry in A3, not yet opened Mechanical in A4 Status after model has solvedwaiting for post-processing Icon MeaningUp to DateRefresh required. Upstream data has changedUpdate required. Local data has changedUnfulfilled. Upstream data does not existAttention RequiredSolvingUpdate FailedUpdate InterruptedChanges pending (was up-to-date, but upstream data has changed). . . Sharing Data between Different Solvers Workbench can be used to transfer data between solvers. In this 1-way FSI (fluid-structure-interaction) example, we transfer the loads from a Fluent CFD simulation over to a Mechanical system to perform a stress analysisThe square connector shows that the geometry created in cell A2 (CFD model) is being shared with cell B3 (FEA model). The round connector shows that the CFD results are being transferred as a Setup (input) condition to be used for FEA stress analysis.. . . File Location on DiskShould you need to identify the individual files on your disk for each stage of the project, these can be found by enabling View > Files. The resulting table will cross-reference the directory and filename with the project cells.Filename Directory. . . Use of Archive / RestoreThe workbench project comprises many files and directories. If you need to either archivethe project, or bundle it to send to us for a Technical Support query, use the ‘Archive’ tool.This generates a single zipfile of the entire project.When archiving, you can choose whetherto include the computed result files or not(omitting these may make it small enoughto send by email)If you restore an archive you can choosewhere you save (and solve) the project.If you double click on a .wbpz file it willunpack the file to the location given byTools>Options>Folder for TemporaryFilesMost Workbench applications will let you specify key quantities as a parameter (rather than a constant). This will be covered later.In this example:•When creating the geometry inDesignModeler, hole diameter is set tobe an input parameter.•When reviewing the results, themaximum stress is set as an outputparameterWe could just have easily set up a CFD analysis, looking at different loading conditions and reporting the pressure drops.•Clicking on ‘Parameter Set’ lets us vary these parameters. •Four different geometric designs are being tested.•The whole process is automated. Workbench will recursively: i.Create the geometry, based on the parameters in the table ii.Take this into Mechanical and remesh and solve and then the postprocessor•The user just needs to sit back and wait, and the matrix of experiments (each requiring several different applicationsto be launched in turn) is computed automatically.1] Create new row in table with each design (in this case hole diameter)3] The desired result (set up in Mechanical) is reported here2] Click here tocompute all the designs4] The ‘Exported’ option allows snapshots of each DP to be saved to a different project… Starting Mechanical There are two methods of launching Workbench: •From the Windows start menu:•From the CAD systemThe Units menu in Workbench:•Select from predefined unit systems.•Create custom unit systems.•Controls unit display for Engineering Data, Parameters and Charts.•Activate the Units System dialog to unit display preferences.Units can be displayed inthe active Project system oras they were defined in theirsource (e.g. CAD system).Create custom unit systems by duplicating existing systems then modifying. Custom unit systems can be exported and imported.. . . License PreferencesWorkbench license control is handled through the user interface shown below, activated from the Workbench project page:“Tools > License Preferences . . . “. . . License PreferencesThe order of license preference is specified using the up/down arrows (first available is used). •The “Use License” column indicates desired licenses to use (0 = off, 1 = on).Workbench users can specify whether a single license isshared when multiple applications are open, or if eachapplication accesses their own license.31 © 2015 ANSYS, Inc. February 27, 2015。

a21 x1 a22 x2 a2 n xn b2 am 1 x1 am 2 x2 amn xn bm
where aij ’s and bi ’s are all real number. We will call this system as m n linear systems.
16
n×n Systems
Example: The system
3 x1
2 x2 x2

x3 x3 2 x3
1 2 4
is in triangular form. It is easy to solve this system. Actually, from the last equation, we have x3 2 . Using this value in the second equation×n Systems
We will restrict ourselves to n n systems. Definition: A system is said to be in triangular form if in the kth equation the coefficient of the first k-1 variables are all zero and the coefficient of xk is nonzero ( k 1, , n) .
6
Systems of Linear Equations
Example: Some linear systems
(a) x1 2 x1 (b) x1 2 x1 2 x2 3 x2 x2 x2 5 8 x3 x3 2 4

兼任 湖北省学位委员会评议组成员、华中师范大学学位 委员会第3、4届委员、教育部人文社科基地华中师大语言 与语言教育研究中心兼职研究员。学术兼职包括全国专业 英语研究会理事、中南地区外语教学法研究会副理事长、 湖北省翻译者协会副会长、武汉欧美同学会常务理事等。 被邀担任教育部全国本科教学评估专家和教育部出国留学 基金语言学评审专家。同时担任上海外语教育出版社教育 部"十五"规划项目英语专业教材编写委员会委员，重庆出 版社中西部英语专业系列教材编写委员会委员。 主讲 英语词汇学、文体学、语义学等理论课程。从事语 言学和应用语言学方面的研究，并对话语篇章、语用、语 言与文化等有浓厚的兴趣。




近年来，汪榕培教授在中国古典文学英译和中西 文化比较等方面取得了突破性的进展，先后完成 了 《英译老子》、《英译易经》、 《英译陶诗》、 《英译诗经》、《英译庄子》、 《英译邯郸记》 《英译汉魏六朝诗三百首》、 《英译牡丹亭》、 《英译孔雀东南飞· 木兰诗》、等译著， 并撰写了一系列相关的论文，出版了专著《比较 与翻译》和《陶渊明诗歌英译比较研究》，得到 国内外学者的高度重视。他目前正在继续进行典 籍英译研究工作，兼任苏州大学、大连理工大学 博士生导师。
What we shall learn in ish lexicology is more than to learn to remember new words，but it will make you powerful in learning new words. 有人误认为词汇学就是“学词汇”。
4.所有作业，独立完成，不能抄袭 ，否则扣分。
Chapter One
The Basic Concepts of Words and Vocabulary

© 2011 Pearson Prentice Hall. All rights reserved.
1-10
Principle 5: Conflicts of interest cause agency problems
The separation of management and the ownership of the firm creates an agency problem. Managers may make decisions that are not consistent with the goal of maximizing shareholder wealth.
© 2011 Pearson Prentice Hall. All rights reserved.
1-13
The Role of Finance in Business (cont.)
Knowledge of financial tools is relevant for decision making in all areas of business (be it marketing, production etc.). Decisions involve an element of time and uncertainty… Financial tools help adjust for time and risk. Decisions taken in business should be financially feasible… Financial tools help determine the financial viability of decisions.
© 2011 Pearson Prentice Hall. All rights reserved.