酷酷小牛仔说明书_20100106

加强版用户手册吉他放大器目录简介 1控制面板 2预设简介 3编辑和保存预设 4访问预设内容 4编辑和保存放大器控制设置 4改变预设中的放大器类型 7MUSTANG LT25 放大器类型 8编辑和保存效果器控制设置 9替换、添加和删除效果器 10用 TAP 键设置延时时间 12MUSTANG LT25 效果器类型 13菜单功能 15调谐器 16脚踏开关 17设置 18恢复 18辅助输入和耳机输出 19 USB 接口 19 FENDER TONE™ 20规格 20简介这本加强版用户手册详尽介绍了关于 Mustang LT25 放大器的特点和功能。

作为对每台放大器附带的《Mustang LT25 快速入门指南》的补充，本手册详细介绍了该放大器的各种功能，其中包括浏览和修改板载预设，以及对放大器和效果器类型的完整说明。

不仅如此，本手册还加入了使用Mustang LT25 的板载调谐器、脚踏开关、USB 接口和其他功能的插图式逐步说明。

虽然这本加强版手册介绍了最新版本的 Mustang LT25，但随着该放大器及其功能不断升级，在使用前请留意是否有更新版本的手册可供参考。

此外，如将 Mustang LT25 与 Fender Tone™ 桌面应用配对可使用更多音色。

请务必定期查看/ rmware/support以获得改进和增强 Mustang LT25 体验的固件更新。

控制面板Mustang LT25 的顶部控制面板包含一个乐器输入接口、五个控制旋钮、一个显示窗口、一个编码器旋钮、四个功能键、一个脚踏开关输入接口，一个辅助输入接口（1/8 英寸），一个耳机输出接口（1/8 英寸），一个 TAPA. 脚踏开关（“FTSW”）：通过此接口连接可选的单键脚踏开关（第 17 页）。

B. 乐器输入接口（INPUT）：通过此接口连接乐器。

C. 辅助输入接口（AUX）、耳机输出接口（耳机图标）：1/8 英寸辅助输入接口，用于连接外部音频设备；1/8 英寸耳机输出接口，用于连接耳机（第 19 页）。

酷雷coolnee蓝牙音箱使用说明书一、注意事项为了使用者正确使用播放器，确保播放器性能良好，请认真阅读并遵守：切勿严重撞击主机。

切勿接触苯、稀释剂等化学药品。

请不要靠近强磁场、电场。

请避开直射光线或发热器具。

切勿自行拆卸、修理、改造。

骑车、驾驶汽车及摩托车时，请勿使用播放器及耳机，以免造成危险。

切勿以较大音量收听，以免对听力造成不良影响。

废弃包装、电池、旧电子产品，请分类妥善处理。

二、功能特点[蓝牙音频]Bluetooth3.0+EDR，最大接收距离10米。

[蓝牙通话]语音清晰、无回声。

[MP3播放]直接播放TF卡内存放的MP3文件。

[FM收音机]FM数字立体声收音机，电台记忆播放。

[音频输入]立体声音频输入接口，轻松连接电脑、数码音乐播放器、手机等音源设备。

[断点记忆]自动记忆上次退出时的曲目，音量大小。

[内置电池]内置可充电锂电池，环保，节能，实用。

[USB读卡器]连接电脑，可拷贝或删除TF卡中的歌曲。

[USB声卡]连接电脑，播放电脑音频文件，可控制电脑上下曲、音量大小。

三、播放音乐操作本机开机时自动检测识别外接设备，开机后进入蓝牙/FM模式，插入TF卡自动识别播放，后者优先原则，也可自行切换播放模式；插入音频信号线不自动切换，通过[O/PLAY]键切换到AUX模式下播放，详细功能操作请阅读第四项“产品的按键、插孔功能定义”。

四、产品的按键、插孔功能定义(以实物为准)1.[ON/OFF]：电源开关；ON为开，OFF为关。

2.[O/PLAY]：播放/暂停/接听电话/挂断电话/模式转换/全自动搜台。

短按：TF、AUX和蓝牙模式为播放/暂停，FM模式为全自动搜台；来电时短按接电话，通话时短按挂机。

长按：长按3秒松开进行模式转换，转换顺序为TF->蓝牙->AUX->FM；3.[-]：音量调节小/上一曲/上一个电台。

短按：TF模式为上一曲；FM模式选择上一个电台；蓝牙/AUX 模式调节音量减小；长按：调节音量减小。

90dB502044S80R/ S80US80US80RS80U -BZ -220-R [Model number][Buzzer][Voltage][Color]||||• S80R • S80U• (Blank)- No buzzer type • BZ- Built-in buzzer type• 12 - DC12V • 24 - DC24V • 110 - AC110V • 220 - AC220VR-Red A-Amber G-Green B-Blue Bulb Revolving Warning LightThank you for purchasing Qlight’s products. Please read this user manual carefully prior to installation and operation to ensure safe and correct use.Failure to follow the instructions below may cause a loss of life or serious physical injury.1. Please remove any objects that can interrupt ventilation around the product.2. Please turn off the power of the product immediately if it fails to operate properly.3. Carefully wire the product according to each product’s specification.4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.5. Do not apply excessive force/impact to the product.6. Failure to follow any of the instructions above may cause malfunction or damage to the product, fire, and electric shock.Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product that would void the warranty.1. During wiring or maintenance, please completely turn off the power of the product. (Failure to follow this may lead to an electric shock.)2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection ratings indicated for each product. (Failure to follow these instructions may cause a fire to the product, electric shock, physical injury, malfunction or damage to the product.)3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to follow these instructions may lead to fire, electric shock, or product damage.)4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to fire, electric shock, or product damage.)5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to follow this may cause damage to property, fire, electric shock and loss of life.)• Protection rating : IP44• Ambient operating temperature : -20°C to +50°CPlease scan the QR code for more detailed product information.S80US80RS80R/ S80U• First, remove the flange nuts from bolts and place the product through the mounting surface holes.• Fasten the flange nuts on the opposite side of themounting surface until the product is tightened securely.• DC/AC type cable specification :External power line - UL1015 AWG18(0.75sq) x 2C 400mm• For built-in buzzer type, there is a shared supply line for the buzzer and lighting element.Power■ Parts Definition/ Installation■ Mounting Hole Specifications• Machine holes on the mounting surface referring to the diagram below.• Please refer to the dimensions below for installation of mounting brackets• This product is designed for use with protection rating of IP44.• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating indicated(IP44), it may cause malfunction or damage to the product.• In case of outdoor applications, install the product in the upright position. Do not install the product horizontal or upside-down positions where water can potentially penetrate into the product and impact it’s operation.• For further information, please visit our website ().Product Operation Inquiry / Customer Support +82-55-328-4082You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.Head office : A-412, 579 Kyungin-Ro, Guro-Gu, Seoul, Korea (Postal Code : 08212)Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)EN-1806A。

牛仔门襟机Cowboy placket machine（MB1003C）使用说明书Instruction Manual常州智谷机电科技有限公司CHANGZHOU WISDOM &VALLEY ELECTRICAL TECHNOLOGY CO.,LTD在使用本设备之前请先阅读本使用说明书Please read the operation manual of the touch screen interface before using the device 请将本使用说明书放在便于查阅的地方保管Please keep this operation manual of touch screen interface in convenient place forreferenc2022.04.18版本信息/Version感谢购买IMB工业用缝纫机。

在使用此机器之前，请仔细阅读以下的说明，这样可以更好地帮到您了解此机器的相关操作。

这些说明是根据现行的条例明确阐述了正确的工作方法。

Thank you for purchasing this industrial sewing machine from IMBBefore using this automatic unit,please read the following instructions,which will help you tounderstand how the machine operates.These instructions illustrate the correct working methods to comply with current regulations.在没有得到IMB授权许可的前提下，此说明书的任何部分是不可以被复制或者转录的。

说明书的内容可能被修改，而不需预先通知。

No part of this manual may be copied or transcribed without requesting prior authorization from IMBThe contents of this manual may be subject to change without advance notification.我们将欣然接受各位提出的改进此说明书的任何建议和指示We are happy to receive suggestions and/or indications on ways we could improve this manual.本机介绍说明分为三部分，具体请参照《MB1003C牛仔门襟机-使用说明书》、《MB1003CA牛仔门襟机-零件手册》、《MB1003C-触摸屏界面操作说明》。

Baby-LIN Product GuideProduct Guide V1.6Lipowsky Industrie-Elektronik GmbHRömerstraße57|64291Darmstadt|Germany Phone:+49(0)6151/93591-0|Fax:+49(0)6151/93591-28 Website:|E-Mail:****************1Imprint22Support information 33Introduction 34Use cases45LINWorks and workflow 46Products61ImprintAuthor Lipowsky Industrie-Elektronik GmbH Römerstraße5764291DarmstadtPhone+49(0)6151/93591-0Fax+49(0)6151/93591-28E-Mail****************Website CEO Andreas LipowskyCommercial register Darmstadt HRB5139VAT-ID DE111647423Quality Management DIN EN ISO9001:2015Title Product GuideVersion V1.5Date2021-09-20Valid for Baby-LIN-DeviceCopyright©2020,Lipowsky Industrie-Elektronik GmbH,DarmstadtThis publication is copyright protected.All rights reserved,including those to translation,performance,use of illustrations and tables,broadcasting, microfilming or reproduction by other means,or electronic storage of all material contained herein.All other brand names and trademarks used within this manual are unlimited subject to the applicable trademark laws and the ownership rights of their registered owners.The hardware,firmware,software and documents of the Baby-LIN-Device are subject to change without prior notice.Lipowsky Industrie-Elektronik GmbH thereby has no obligations.2Support informationIn case of any questions you can get technical support by e-mail or phone.We can use T eamViewer to give you direct support and help on your own PC.This way we are able to sort out problems fast and direct.We have sample code and application notes available,which will help you to make your job.Lipowsky Industrie-Elektronik GmbH realized many successful LIN and CAN related projects and therefor we can draw upon many years of experience in thesefields.We also provide turn key solutions for specific applications like EOL(End of Line)testers or programming stations.Lipowsky Industrie-Elektronik GmbH designs,produces and applies the Baby-LIN products,so you can always expect qualified and fast support.3IntroductionAny situation that requires communication with a LIN or CAN device is a potentialfield of application for a Baby-LIN product.It is a versatile tool that can be used in research laboratories,test departments and production(EOL applications).All Baby-LIN products allow for different operation modes to support typical use cases like:•Monitor and log all frames on the bus without the need for a SDF.If a SDF is available signal values can also be monitored.•Control the bus via the LINWorks software or customer specific applications by using the Baby-LIN-DLL.•Program and store free programmable command sequences in the Baby-LIN product to run it as a standalone device without the need for a PC.Thus you can run a bus driven ECU in a durability test or EOL applications without any PC connected.All Baby-LIN products are able to simulate different configurations of LIN-and CAN-Bus nodes.It is possible to simulate any number of nodes ranging from none to all.These are some typical configurations:•LIN-Bus:Simulate the LIN-Bus master to operate slave nodes.•LIN-Bus:Simulate any number of LIN-Bus slave nodes.•LIN-and CAN-Bus:Simulate all but one node and realize a residual bus simulation.•LIN-and CAN-Bus:Simulate all nodes and therefor the complete communication on the bus.•LIN-and CAN-Bus:Simulate no node to monitor the bus communication only.Simulations for the LIN-and CAN-Bus can be done simultaneously.The different Baby-LIN products mainly vary in the type and amount of interfaces and the possibilities to interact without a PC.The following guide is designed to help youfind the ideal Baby-LIN product for your use cases.4Use casesEach Baby-LIN product is designed to comply with certain requirements of typical use cases:No matter if you want a PC coupled device,a handheld device,a stand alone device without a PC or a PLC coupled device,there is always a Baby-LIN product for you.5LINWorks and workflowAll the different software components of the LINWorks suite are designed to support the customer during specific steps of the workflow.The worklfow starts with a LDF(for LIN-Bus)or DBC(for CAN-Bus)which will be embedded in a SDF using the Session Configurator.This SDF contains all the informations the Baby-LIN product needs.Depending on your device and use case you can transfer the SDF via Web-Interface,USB mass storage device,SDHC card or the Simple Menu.It is also the base for your custom application using the Baby-LIN-DLL.The purchase of a Baby-LIN product includes the license to download the LINWorks suite.This suite is a collection of PC software that supports you during the whole workflow.The LDFEdit allows the inspection,creation and edit of a LDFile(LIN Description File).The SessionConf allows the inspection,creation and edit of a SDFile(Session Description File)and features afile import for LDFiles(for LIN-Bus simulation)and DBCfiles.It defines everything needed for a complete simulation of each available bus,e.g.which nodes on each bus are available and which nodes should be simulated by the Baby-LIN product.Moreover it allows defining an application logic.This programming ability is available for each device out of the box.The SimpleMenu is used to establish a connection to the Baby-LIN product and upload SDFiles,change the device target configuration,control the bus and monitor the frames and signals on the bus.Even without a LDFile/DBCfile/SDFile the bus can be monitored and the frames can be logged.The Baby-LIN-DLL allows customers to create their own application and use all features of the Baby-LIN product like controlling and monitoring the LIN-and CAN-Bus interfaces.The Baby-LIN-DLL is a native C/C++DLL.A wrapper for∗∗.NET∗∗applications is also provided as LabViewfiles.Examples are available for all supported languages.The LogViewer can show and convert the logfiles of the Baby-LIN products as well as the SimpleMenu.The LINWorks software runs on32and64bit Windows versions.The Baby-LIN-DLL is also available as Linux version upon request.6ProductsBaby-LIN-II Baby-LIN-RC-II Baby-LIN-RM-III HARP-5Baby-LIN-MB-IIUSB2.0USB2.0USB2.0USB2.0SDHC cardEthernetRS-232web interface111111151CAN-HS1CAN-LS1CAN-HS1CAN-LS1CAN-HS120/16/6。

Revolutionize the way you sergeIn 1964, several engineers and middle managers at a Japanese industrial company believed that they could redesign the industrial serger they were currentlymanu-facturing to be smaller and lighter. Theircompanyrejected theconcept,but the team was so committed to their idea that they quit their jobs and formed their own company.After three years of research, working prototypes and a battery of tests, they created a “baby” serger for home sewers that was capable of producing an overlock stitch. This was the birth of a revolutionary machine called Baby Lock. For the first time, home sewers could create garments and other projects with a finished, professional look.Today, you’ll find a variety of stitches and easy threading options on every Baby Lock serger, as well as exclusive features that make Baby Lock sergers stand out from the rest. The patented ExtraordinAir™ Threading is by far the easiest way to thread a serger. And the patented Wave Stitch – a beautiful and unique stitch exclusive to Baby Lock – is available on two of our newest sergers, the Evolution and the Enlighten.Baby Lock is proud to have brought the first serger to the home market. It’s this heritage that moves us to continue revolutionizing the way you serge by offering the easiest sergers to thread, with fourteen exclusive patents that control tensions, chain off the cover stitch and more. Keep reading to discover why Baby Lock sergers are the most revolutionary sergers in the industry.114 Patents Exclusive TO BABY LOCKTubular LoopersBaby Lock eliminates threading mistakes and protects thread, with no exposed thread and no thread guides to tangle with. Enjoy tubular loopers that can be threaded in any order, giving you more freedom to serge than ever before!Looper Drive SystemProtect your machine from needing repairs and serge worry free! This exclusive Looper Drive System is built to last, preventing loopers from becoming misaligned or out of timing, reducing the possibility of major looper damage.Advanced Knife Driving & One-Way Clutch SystemsCut thicker fabrics with incredible ease using the exclusive lower-mounted knife system with a larger cutting bite.ExtraordinAir™ & Jet-Air Threading™Baby Lock’s patented ExtraordinAir and Jet-Air Threading technology takes away any threading struggles. With one touch of a button or lever, thread is whisked through the tubular upper, lower, and chain stitch loopers.Automatic Thread Delivery System Having no tensions, Baby Lock sergers will deliver a balanced stitch on any fabric with any type of thread, all of the time. Go from one fabric to another without interruption. With Baby Lock’s Exclusive Automatic Thread Delivery System (ATD), simply set the stitch you want and serge away.It Started With A Revolutionary Idea…2 Full-Featured Differential FeedDiscover stronger feeding as well asmore consistent gathering on all fabrics.Baby Lock took the differential feedmechanism to a new level by adding asingle unit feed dog mechanism.Adjustable Stitch Length & AutomaticRolled Hem DialStitch length can effortlessly be adjustedon a Baby Lock serger using one dialwithout changing a foot or needle plate.This dial includes an Automatic RolledHem setting that will retract the built-institch finger for a rolled hem.Fabric Support SystemBaby Lock’s Jet-Air sergers include aFabric Support System to keep stitchesflat and balanced, no matter whatspeed, fabric or stitch you choose. Thebuilt-in stitch fingers actually move withthe knife blade, adjusting the seamsimultaneously with the cutting width.Vertical Needle PenetrationAvoid needle deflection and protectyour fabric. While most machines useslanted needles that push and damagefabric, Baby Lock’s needles are setvertically to powerfully sew by movingdirectly up and down.Chain/Cover T ension DisksSave time by adjusting the chain, coverand triple cover stitch needles with onetension dial. Baby Lock revolutionizedthe cover stitch with the Evolution, whichfunctions include chain, cover, and triplecover stitches.Thread Delivery Unit for the ExclusiveWave StitchThe exclusive Wave Stitch is a gorgeousdecorative addition to projects of everykind. For a stitch this unique, Baby Lockwanted to ensure that each wave wouldbe even with the next and they createda thread delivery unit to give each one aflawless look.8/7/6 Thread Stitch CapacityThe Evolution is the only serger with8 threads, providing more stitchcombinations than ever before - 87 inall! Baby Lock was also the first in theworld to combine overlocking and coverstitching in the same operation, creatingtwo machines in one!Cover Stitch Chaining OffBaby Lock has made cover stitching easyby automatically chaining off to eliminateunnecessary steps and frustration.Needle Threading SystemBaby Lock has put a lot of thought intothreading a serger, but they haven’tforgotten about the most important part- the needles. Lock the needle threaderin place and easily thread the needleswith the touch of a lever.This advanced 8-thread serger brings you the latest evolution in threading technology with ExtraordinAir TM threading. With just one push of a button, ExtraordinAir takes your thread through all three loopers at once, instantly, with a gust of air. Plus, you’ll have the luxury of Baby Lock’s exclusive patented features that allow you to thread in any order, eliminate tensions, and take your creativity further than you’ve ever dreamed a serger could take it.EVOLUTIONThe World’s Most Advanced Serger3This revolutionary serger features the latest in threading technology, ExtraordinAir TM Threading. With just one push of a button, ExtraordinAir TM takes your thread through all loopers at once, instantly, with a gust of air. With so much time saved on serging – plus the beautiful and exclusive Wave Stitch – you’ll have the time and the freedom to expand your creativity. Get enlightened today!ENLIGHTENArtistically Advanced Wave Serger5710PBS Host of “Sewing With Nancy”13I’ve joined the Baby Lock serger rEvolution - have you?Baby Lock sergers can revolutionize the way you serge in more ways than you can imagine. Before I found Baby Lock, I used several different sergers for each episode of Sewing With Nancy. I needed a serger for each setting because it took too long to adjust settings in between takes. But I only needed one Baby Lock serger – changing the settings and thread was that quick and easy.Since then, Baby Lock has never stopped amazing me with thoughtful, exclusive features. With just one touch of a button, ExtraordinAir Threading sends thread through all the loopers with a powerful gust of air – with just one try, you’ll be ready to join the Baby Lock serger revolution too. And with the Automatic Thread Delivery System (ATD), I can thread my machine in any order and I never have to adjust the tensions.I love the finished look that sergers bring to my projects, and now it’s easier than ever to add decorative stitching, interesting textures, flawless seams and more. Baby Lock sergers have changed the way I serge forever - and with their easy-to-use features and professional results, it’s sure to revolutionize the way that you serge, too. Whether you’re looking for your first serger or you’re upgrading your current machine, you’ll find a Baby Lock serger with the functions and features that are perfect for you.Happy Sewing,Nancy ZiemanSerger FAMILY OVERVIEW14Baby Lock Supports Independent Retailers For a retailer near you call 800-422-2952LBCB-SERGER10/09。

EXPANDED OWNER’S MANUALCONTENTSIntroduction 1 Panel 2 ControlPresets Basics 3Editing and Saving Presets4 Accessing Preset Contents 4Editing and Saving Amplifier Control Settings 4Changing the Amplifier Model in a Preset 7Models 8 List of Mustang LT40S AmplifierEditing and Saving Effects Control Settings 9Replacing, Adding and Deleting Effects 10Setting Delay Times with the Tap Button 12List of Mustang LT40S EffectModels 13 Functions15 M enuTuner 16Footswitch 17Settings 18Restore 18 Auxiliary Input and Headphone Output19 Port 19 USBTone™20 FenderSpecifications20INTRODUCTIONThis expanded owner’s manual is a thorough user’s guide to the features and functions of the MustangLT40S amplifier.As a complement to the Mustang LT40S Quick Start Guide that comes with each amplifier, this manual pres-ents a detailed look at the amp’s versatile features. This includes navigation and modification of the onboard presets, and comprehensive descriptions of the amplifier and effect models. It also includes illustrated step-by-step instructions for using Mustang LT40S’s onboard tuner, footswitch, USB port and other functions. While this expanded manual presents the most current version of the amplifier, also check back for updated manual versions that will serve as even more helpful guides as Mustang LT40S and its capabilities evolve. Further, Mustang LT40S offers even more tonal possibilities when paired with the Fender Tone™ desktop app. Be sure to check /firmware/support regularly for firmware updates that improve and enhance the Mustang LT40S experience.CONTROL PANELThe Mustang LT40S top control panel consists of an INSTRUMENT INPUT, five CONTROL KNOBS, a DISPLAY WINDOW, an ENCODER wheel, four UTILITY pushbuttons, a FOOTSWITCH INPUT, an AUXILIARY INPUT (1/8”),A. FOOTSWITCH (“FTSW”): Connect optional single-button footswitch here (page 17).B. INPUT: Plug instrument in here.C. AUXILIARY INPUT, HEADPHONE OUTPUT: 1/8” auxiliary input for connecting external audio devices,and 1/8” output for headphone use (page 19). Headphone output disables speaker.D. GAIN: Affects gain setting in each preset.E. VOLUME: Affects individual volume of each preset.F. TREBLE: Affects treble tone setting in each preset.G. BASS: Affects bass tone setting in each preset.H. MASTER VOLUME: Controls actual overall volume.I. DISPLAY WINDOW: Shows preset in use, preset contents and parameters, and other functions (i.e., tunerand other menu functions).J. ENCODER: Rotary control with press-switch function. For viewing, selecting and adjusting Mustang LT40S presets, controls and other functions.K. UTILITY BUTTONSBACK: Returns user to the previous screen or original preset screen.SAVE: For saving preset modifications, renaming presets and saving presets to a new location.MENU: For accessing tuner, footswitch and other functions (page 15).TAP: For setting delay times (page 12) and accessing built-in tuner (page 16).L. TAP LIGHT: Flashes in time with delay effects.M. POWER: Turns amplifier on and off.N. USB PORT: Amp connection point for USB audio recording (page 19).O. IEC POWER INLET (REAR PANEL; NOT SHOWN): Using the included power cord, connect to a grounded outlet in accordance with the input power voltage and frequency specified at the power inlet.PRESET BASICSMustang LT40S features 30 sequentially numbered presets. Each preset consists of an amplifier and one or more effects (or, in some cases, no effects). Note that when turning the amplifier on, the default active preset is always factory preset 01. Further, 30 empty presets are available when using the “REPLACE” feature (page 7).Mustang LT40S’s 30 factory presets are: 01 FENDER CLEAN 11 METAL LEAD21 TOUCH WAH 02 SILKY SOLO 12 VINTAGE TREMOLO 22 SUPER ROCK 03 CHICAGO BLUES13 SUPER DRYCLEAN 23 NICE FLANGER 04 CLASSIC ROCK 14 THRASH OVERKILL 24 VIBRA DOOM 05 DREAMY 15 CLEAN DELAY 25 SURF MUSIC 06 COUNTRY PICKING 16 OCTOBOT ONE NOTE26 BLUES LEAD 07 SKATE PUNK 17 LITTLE CHAMP 27 ROCK A BILLY 08 SOLO MIDBOOST 18 PHASER SWIRL 28 GARAGE FUZZ 09 JAZZ AMP19 60S FUZZ29 SPACE TRAVEL 10 BRIT 64 RHYTHM20 MYTHIC CRUNCH30 ACOUSTIC SIMBe sure to check /firmware/support regularly for additional presets available for download, and for firmware updates that improve and enhance the Mustang LT40S experience.EDITING AND SAVING PRESETSPresets can be easily edited and, if desired, renamed and saved in place or saved in a different location. The controls of each amplifier type can be adjusted, or an amp model can be replaced with a different one. Simila-ry, various effects controls can be adjusted, or effects can be removed from or added to a preset.When a preset is active, the box containing its number is blue, indicating that no edits have been made. Once an edit is made, the box containing the preset number turns red and the preset title screen will read “UN-SAVED”. When edits are saved, the preset number box returns to blue and the “UNSAVED” title clears. ACCESSING PRESET CONTENTSTo access the contents of a preset, press the ENCODER. From the top down, the DISPLAY WINDOW will then show the number and name of the preset, the amplifier type in use, and four boxes that organize the effects used for that preset (if any). These effects category boxes are labeled STOMP (stompbox), MOD (modulation),EDITING AND SAVING AMPLIFIER CONTROL SETTINGSThere are two ways to adjust an amp control knob setting. A control parameter that corresponds to an actual physical knob on the control panel can be adjusted simply by turning the physical control knob until the*At this point, press the ENCODER or the BACK utility button (green arrow ) to accept the adjusted control val-ues. Pressing BACK returns the user to the preset contents screen; pressing the ENCODER lets the user contin-Note that for control parameters such as MIDDLE that have no corresponding physical knob on the control panel, this is the only method of adjustment.IMPORTANT: If edited amp control settings are not saved, the preset will revert to its original amp control settings when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save edited amp control settings, press the SAVE utility button and use the ENCODER to scroll to one of three options—SAVE, SAVE AS or REPLACE. Each is detailed below.SAVE: Keeps an edited preset in the same location with the same name. To do this, press the SAVE utilitySAVE AS: Enables saving an edited preset in a different position, with or without a different name. To do this, pressWhether renaming the preset or not when using “SAVE AS”, a name must be entered by pressing the ENCOD-ER to activate a cursor, then spelling out the name by turning and pressing the ENCODER to scroll through and select characters. All characters can be cleared by using the ENCODER to scroll to and select “CLEAR ALL”. When name entry is completed for the new location, save it by pressing the SAVE utility button or by usingREPLACE: Any existing preset can be replaced with another by pressing the SAVE utility button, using the ENCODER to scroll to and select “REPLACE” and choosing from 60 replacement presets (the 30 factory pre-sets, plus 30 empty presets). After selecting “REPLACE”, use the ENCODER to scroll to any of the 60 available presets; each one is automatically “previewed” so the user can hear the sound before the preset is loaded.CHANGING THE AMPLIFIER MODEL IN A PRESETThe amplifier model in a preset can be replaced with another one (see list of Mustang LT40S amplifier mod-els on page 8). To do this, acess the contents of a preset by pressing the ENCODER on it; the amp model will automatically be highlighted. Press the ENCODER again to see a list of controls for the amp model in use; the name of the amp model appears at the top of this list.Press the ENCODER once more to activate the amplifier replacement function; the box surrounding the amp name will turn from blue to red, and white arrows will bracket the amp name. Turn the ENCODER to scroll to a new amp model. Press the ENCODER to accept the amp model change, after which the box surrounding theIMPORTANT: If an amplifier replacement is not saved, the preset will revert to its original amp type when re-turning to the preset after leaving it, or when turning the amplifier off and back on again. To save a preset amp replacement, follow the SAVE, SAVE AS or REPLACE instructions on page 6 and at the top of this page.MUSTANG LT40S AMPLIFIER MODELSThis table lists the amp models in Mustang LT40S. The amp label used in each preset appears in the lefthand column, followed by the amp type and a brief description in the righthand column.PRESET AMP LABEL AMP TYPE AND DESCRIPTION50S TWIN Based on a 1957 Twin—an original-era 2x12” Fender tweedclassic prized for clean-to-dirty versatility60S UK CLN Inspired by the Vox AC30, which powered the British Invasionand produced remarkable clean and dirty tone70S ROCK Inspired by a late-’60s/early-’70s Marshall Super Lead, theamp that powered the dawn of hard rock70S UK CLN Inspired by the original 100-watt Hiwatt DR103, which isthe classic cleaner-tone British stack80S ROCK Inspired by the Marshall JCM800, which produced quintessential ’80s metal tone90S ROCK Based on the Mesa Dual Rectifer, which featured distinctivedistortion that shaped the “nu-metal” soundBASSMAN Based on the venerable ’59 Bassman®—one of Fender’s greatest tweed amps, whichbegan life as a bass amp before being adopted by countless guitaristsBURN Based on the “burn” channel of the modern Fender Super-Sonic amp, which has twocascading preamp gain stages for pronounced sustain CHAMP Based on the ’57 Champ®—the small but mighty late-’50s Fender recording greatDELUXE CLN Based on the highly popular 1965 Fender Deluxe Reverb®—an amp with great tonewhether clean or dirty, and cranked in countless clubsDELUXE DIRT Based on a 1957 Deluxe™—a medium-power late-’50s Fender tweedclassic known for thick, compressed overdrive DOOM METAL Inspired by the “sludgy” majesty of the Orange OR120EXCELSIOR An elegantly eccentric modern-day Fender model with thedistinctive thump of a 15” speakerALT METAL Based on the distinctive nu-metal-defining distortion of the Mesa Dual Rectifier, gat-ed with a very fast attenuation curve especially ideal for high-gain metal METAL 2000Modern high-gain scorch based on the EVH® 5150IIIPRINCETON Based on a 1965 Princeton®—a mid-’60s Fender studio favorite withthe snappy tone of a single 10” speakerSMALLTONE Inspired by the garage-classic 1960s Sears Silvertonebeloved of retro/alternative playersSUPER CLEAN Direct-to-mixing-desk studio-preamp purity withclean, uncolored tonal responseSUPER HEAVY Modern high-gain scorch based on the EVH® 5150III, gated with a very fast attenua-tion curve especially ideal for high-gain metalTWIN CLEAN Based on the 1965 Fender Twin Reverb®—an indispensable mid-’60s stage-and-studio favorite prized for producing the Fender clean toneChamp, Deluxe, Bassman, Princeton, Deluxe Reverb and Twin Reverb are trademarks of FMIC. All other non-FMIC product names and trademarks appearing in this manual are the property of their respective owners and are used solely to identify the products whose tones and sounds were studied during sound model development for this product. The use of these products and trademarks does not imply any affiliation, connection, sponsorship, or approval between FMIC and with or by any third party.EDITING AND SAVING EFFECTS CONTROL SETTINGSTo edit and save individual control settings of a preset’s various effects (if any), first select the effect categoryThe DISPLAY WINDOW will then show a list of controls for the effect model in use in that category; use the EN-At this point, press the ENCODER to accept the adjusted effect control value and exit edit mode; the sur-IMPORTANT: If an edited effect control setting is not saved, the preset will revert to its original effect control settings when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save edited effect control settings, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.REPLACING, ADDING AND DELETING EFFECTSAs noted, each of the four effect category boxes can contain one effect. If an effect is present, it can be re-placed with another effect in that category, or it can be deleted. If no effect is present, one can be added (seePress the ENCODER once more to activate the effect replacement function; the box surrounding the effect name will turn from blue to red, and white arrows will bracket the effect name. Turn the ENCODER clockwise to scroll through other effects models in that category. Press the ENCODER to accept a replacement effectTo delete an effect, the steps are very similar to those on page 10. As before, access the contents of a preset by pressing the ENCODER on it, then use the ENCODER to scroll to an occupied effect category box. Press thePress the ENCODER once more to activate the effect replacement function; the box surrounding the effect name will turn from blue to red, and white arrows will bracket the effect name. Turn the ENCODER counter-lockwise until the red-highlighted effect label at the top of the DISPLAY WINDOW reads “NONE”. Press theTo add an effect to an empty effect category box, first access the contents of a preset by pressing the ENCOD-ER on it, then use the ENCODER to scroll to the empty effect category box. Press the ENCODER again to accessTurn the ENCODER clockwise to scroll through effects models in that category. Press the ENCODER on the desired effect, after which the box surrounding the effect name will return to blue and the effect is added—although not yet saved—to that effect category box. Alternately, press the BACK utility button (green arrow) to return to the preset contents screen (see illustrations on next page):IMPORTANT: If an effect is not saved once it has been replaced, deleted or added, the preset will revert to its original effect model(s) when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save a changed, deleted or added effect model, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.SETTING DELAY TIMES WITH THE TAP BUTTONMUSTANG LT40S EFFECT MODELSThis table lists the effect models in Mustang LT40S, organized into the four categories that appear in each pre-set—STOMP (stompbox), MOD (modulation), DELAY and REV (reverb). The effects labels used in each preset appear in the lefthand column, followed by the effects types and a brief description in the righthand column.STOMPBOX EFFECTSOVERDRIVE Versatile Fender overdriveBLUES DRIVE Overdrive effect inspired by the original late-’70s Ibanez TS808 Tube ScreamerMYTH DRIVE Overdrive effect inspired by the ’90s-era Klon CentaurROCK DIRT Distortion effect inspired by the Pro Co RATFUZZ Versatile Fender fuzz with variable low-end response specially designed for Mustang LT40SBIG FUZZ Distortion effect inspired by the Electro-Harmonix Big MuffOCTOBOT Synth-like combination of octave-down effect plus octave-up fuzzCOMPRESSOR Compressor effect inspired by the classic MXR Dyna CompSUSTAIN Inspired by the MXR M-163 Sustain, a rare 1980s compressor pedal with an especiallystrong compression effect and short attack time METAL GATE Noise gate with a very fast attenuation curve especially ideal for high-gain metal5-BAND EQ Five-band graphic equalizerMODULATION EFFECTSCHORUS Distinctive chorus effect that uses a triangle wave for modulationFLANGER Distinctive flanging effect that uses a triangle wave for modulationVIBRATONE Classic late-’60s/early-’70s Fender effect with a rotating speaker baffleTREMOLO Smoothly pulsating tube bias tremolo, as heard in ampssuch as the Fender Princeton ReverbPHASER Long-indispensable jetliner “whoosh” heard on countless recordingsSTEP FILTER Rhythmically choppy effect that dices notes into distinctly alternating “steps”TOUCH WAH Wah effect controlled by picking dynamics rather than an expression pedalAll non-FMIC product names and trademarks appearing in this manual are the property of their respective owners and are used solely to identify the products whose tones and sounds were studied during sound model development for this product. The use of these products and trademarks does not imply any affiliation, connection, sponsor-ship, or approval between FMIC and with or by any third party.DELAY EFFECTSNote that the control panel TAP utility button and TAP LIGHT work in connection with effects in this category only.DELAY Clean, simple and pristine signal repetitionREVERSE Reverses the delayed signal for the classic “backwards guitar” effectECHO Tape delay effect based on the analog classic Maestro Echoplex, which had tape im-perfections that created distinctive “wow” and “flutter”REVERB EFFECTSLARGE HALL Strong, bright reverb simulating the size of, for example, a majorperformance hall and other large, cavernous spaces SMALL ROOM Warmer, less echo-y reverb typical of smaller spaces and classic echo chambersSPRING 65Fender reverb effect built into classic mid-’60s Fender ampsPLATE The reverb type heard on countless recordings, based on theclassic (and pool table-sized) EMT 140ARENA Simulates the long-trailing reverberation typical of large stadiums and arenasAll non-FMIC product names and trademarks appearing in this manual are the property of their respective owners and are used solely to identify the products whose tones and sounds were studied during sound model development for this product. The use of these products and trademarks does not imply any affiliation, connection, sponsor-ship, or approval between FMIC and with or by any third party.MENU FUNCTIONSMustang LT40S features four convenient MENU functions—TUNER, FOOTSWITCH, SETTINGS and RESTORE—TUNER: Enables use of Mustang LT40S’s built-in chromatic tuner (page 16).FOOTSWITCH: For configuring Mustang LT40S’s single-button footswitch to provide easy hands-free selec-tion of any two presets (page 17).SETTINGS: Displays the firmware version (page 18). Also includes a gain control for use when recording using the USB audio port on the control panel (page 19).RESTORE: Enables restoration of factory presets and amplifier settings (page 18).MENU FUNCTION: TUNERThe second way is to press the MENU utility button on the control panel; the list of MENU functions willTo use the TUNER, sound a note; the letter name of the pitch will appear in the box at bottom and the shorter vertical bars on either side of the longer vertical center bar will illuminate red to indicate varying degrees of“A” PITCH SLIGHTLY FLAT“A” PITCH IN TUNENote that speaker output is muted when tuning, and that the volume control on the instrument being tuned must be turned up sufficiently to register a TUNER reading.MENU FUNCTION: FOOTSWITCHConnect an optional Fender single-button footswitch (PN 0994052000) by plugging it into the “FTSW” jack on the control panel. The footswitch provides convenient hands-free switching between two pre-determined “quick-access” presets. The second MENU function—FOOTSWITCH—enables easy configuration of any twoTwo presets will be shown in the DISPLAY WINDOW below the header “QUICK ACCESS”; the upper preset is au-tomatically highlighted in blue. To choose a new preset for this upper quick-access position, press the ENCOD-Press the ENCODER to select the new upper quick-access preset; the box surrounding the preset name willIMPORTANT: If quick-access footswitch presets are not saved, the quick-access preset slots will revert to their original contents when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save quick-access footswitch presets, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.MENU FUNCTION: SETTINGSThe third MENU function—SETTINGS—displays the current firmware version and features a gain control for use when recording using the USB port on the control panel. To access these options, press the MENU util-Be sure to check /firmware/support regularly for firmware updates that improve and enhance the Mustang LT40S experience.MENU FUNCTION: RESTORETo initiate restoration use the ENCODER to scroll to and select “YES RESTORE”. To cancel restoration, press theTurn the ENCODER to set a new “USB GAIN” value. Press the ENCODER to accept the new value; the surround-the actual physical GAIN control knob on the control panel does not affect USB recording.SPECIFICATIONSTYPEPR 6015POWER REQUIREMENTS 118 wattsPOWER OUTPUT 40 watts (2x20 watts stereo)INPUT IMPEDANCE 1MΩ (instrument) 15kΩ (aux)SPEAKERS Two 4” Full-Range Fender® Special Design (8Ω)FOOTSWITCHRecommended: Fender 1-Button Economy On-Off Footswitch (optional, PN 0994049000)DIMENSIONS AND WEIGHTWidth: 14.4” (36.5 cm) Height: 8” (20.4 cm) Depth: 8.3” (21 cm) Weight: 12.25 lbs. (5.56 kg)Product specifications subject to change without notice.Be sure to check /firmware/support regularly for additional presets available for download, and for firmware updates that improve and enhance the Mustang LT40S experience.FENDER TONE™Fender Tone —the ultimate desktop companion to Mustang LT amplifiers for Mac and PC—is available as a free download from /ToneDesktop . With an easy-to-use interface, Tone users can have conve-nient control over existing Mustang LT40S functions, plus access to additional presets and many other fea-tures, including:• Firmware updates• Dozens of additional Fender presets for auditioning and downloading • Preset creation and editing with convenient “undo” feature• Preset editing (replacing amp and effect models, and modifying parameters)• Preset saving, renaming, moving and clearing • Preset backup and restore •Effect bypassLearn more about Fender Tone at /ToneDesktop, and find support materials at /ToneSupport .A PRODUCT OFFENDER MUSICAL INSTRUMENTS CORP.311 CESSNA CIRCLECORONA, CALIF. 92880 U.S.A.AMPLIFICADOR DE AUDIOIMPORTADO POR: Fender Ventas de México, S. de R.L. de C.V.Calle Huerta #279, Int. A. Col. El Naranjo. C.P . 22785. Ensenada, Baja California, México.RFC: FVM-140508-CI0Servicio al Cliente: 01(800) 7887395, 01(800) 7887396, 01(800) 7889433Fender® and Mustang™ are trademarks of FMIC.Other trademarks are property of their respective owners.Copyright © 2021 FMIC. All rights reserved.PN 7722422000 rev . A部件名称本表格依据 SJ/T 11364 的规定编制。

目录第一章操作显示面板 (1)第二章操作按键 (2)2.1 功能按键 (2)2.2 数字/字母按键 (2)2.3 方向按键 (3)2.4 运行模式按键 (4)2.5 动作按键 (4)2.6 紧急停止开关及其它电气开关 (5)第三章面板显示及操作页面 (6)3.1 面板画面显示 (6)3.1.1 状态栏 (6)3.1.2 画面主菜单 (7)3.2 功能操作页面 (8)3.2.1 启动页面 (8)3.2.2 主监视页面 (9)3.3 开/合模设定页 (11)3.3.1运动参数页面 (12)3.3.2 调模页面 (13)3.3.3 润滑页面 (14)3.4 顶针、吹风设定页 (15)3.4.1运动参数 (16)3.5 中子设定页 (18)3.5.1 设置模式 (19)3.5.2 时间设定 (20)3.5.3 斜率调整 (20)3.6注射、保压设定页 (21)3.6.1运动参数 (21)3.6.2注射辅助 (23)3.7 熔胶和松退页面 (23)3.7.1运动参数 (23)3.8 射台运动和清料页面 (26)3.8.1 运动参数 (27)3.9 温度页面 (28)3.9.1 加热设定页面 (29)3.10 登录/注销页面 (30)3.11 模具数据页面 (31)3.12 温度数据”页面 (32)3.13 “机器数据”页面 (32)3.14 “生产管理”页面 (33)3.15 IO监控画面 (34)3.16 生产过程数据（PDP）画面 (35)3.17 质量监控（SPC）画面 (36)3.18 “浏览”页面 (37)3.19 “历史信息”页面 (38)3.20 “注射曲线图”页面 (39)3.21 校准页面 (40)3.21.1压力校正 (40)3.21.2 流量校正 (41)3.22 设定显示 (42)3.23 软件版本 (42)第四章整机运行操作 (43)4.1 手动操作 (43)4.2 半自动操作 (43)4.3全自动操作 (43)第一章操作显示面板操作面板提供操作者与机器间的沟通介面。