太阳能充电器使用说明书

太阳能电池板智能充电器使用说明书充电及超压指示：当系统连接正常，且有阳光照射到光电池板时，充电指示灯(1)为绿色常亮，表示系统充电电路正常；当充电指示灯(1)出现绿色快速闪烁时，说明系统过电压，处理见故障处理内容；充电过程使用了PWM方式，如果发生过过放动作，充电先要达到提升充电电压，并保持30分钟，而后降到直充电压，保持30分钟，以激活蓄电池，避免硫化结晶，最后降到浮充电压，并保持浮充电压。

如果没有发生过放，将不会有提升充电方式，以防蓄电池失水。

这些自动控制过程将使蓄电池达到最佳充电效果并保证或延长其使用寿命。

蓄电池状态指示：蓄电池电压在正常范围时，状态指示灯(2)为绿色常亮；充满后状态指示灯为绿色慢闪；当电池电压降低到欠压时状态指示灯变成橙黄色；当蓄电池电压继续降低到过放电压时，状态指示灯(2)变为红色，此时控制器将自动关闭输出，提醒用户及时补充电能。

当电池电压恢复到正常工作范围内时，将自动使能输出开通动作，状态指示灯(2)变为绿色；负载指示：当负载开通时，负载指示灯(4)常亮。

如果负载电流超过了控制器1.25倍的额定电流60秒时，或负载电流超过了控制器1.5倍的额定电流5秒时，故障指示灯(3)为红色慢闪，表示过载，控制器将关闭输出。

当负载或负载侧出现短路故障时，控制器将立即关闭输出，故障指示灯(3)快闪。

出现上述现象时，用户应当仔细检查负载连接情况，断开有故障的负载后，按一次按键即恢复正常输出。

负载开关操作：控制器上电后默认负载输出为关闭，在正常情况下，每按一次按键，负载输出即改变一次开关状态。

当负载输出为开时，负载指示灯(4)常亮；当负载为关闭时，负载指示灯(4)常灭；当负载过载时，故障指示灯(3)慢速闪烁，当负载发生短路时，故障载指示灯(3)快速闪烁。

负载过载或短路控制器均会关闭输出。

第一次发生负载短路30秒后自动恢复输出若还没排出短路故障只能手动恢复输出。

如复位过载、短路保护，排出负载的短路或过载故障，按一次按键，即恢复正常输出。

MPPT2024Z 太阳能充放电控制器使用手册安装、使用前请仔细阅读该手册 武汉万鹏科技有限公司 h t t p ://w w w .j u t a s o l a r .c o m 武汉万鹏科技有限公司 ht t p ://w w w.j u t a s o l a r .c o m 科技有限公司t a s o l a r .c o mMPPT2024Z 太阳能充放电控制器使用手册 版本V1.1目录 1. 安全事项............................................................................................................3 2. MPPT2024Z 控制器介绍.....................................................................................3 2.1 产品概述..................................................................................................3 2.2 产品结构..................................................................................................3 2.3 产品功能..................................................................................................4 2.4 最大功率点跟踪（MPPT）技术介绍......................................................6 3.系统规划参考....................................................................................................7 3.1 系统电压等级..........................................................................................7 3.2 太阳能电池配置......................................................................................8 3.3 配线..........................................................................................................8 3.4 过流保护..................................................................................................9 3.5 雷击保护..................................................................................................9 3.6 接地..........................................................................................................9 3.7 系统扩容..................................................................................................9 4.安装说明..........................................................................................................10 4.1 产品外形尺寸........................................................................................10 4.2 系统接线示意图....................................................................................11 4.3 线材工具准备........................................................................................11 4.4 安装过程................................................................................................11 5.使用说明..........................................................................................................12 5.1 按键功能说明........................................................................................12 5.2 LED 指示状态说明.................................................................................12 5.3 系统类型查看........................................................................................13 6.故障处理..........................................................................................................13 6.1 控制器保护后处理方法........................................................................13 6.2 常见故障现象及处理方法....................................................................14 7.技术参数..........................................................................................................15 8. 保修承诺. (16)武汉万鹏科技有限公司 h tt p ://w w w .j u t a s o l a r .c o m 武汉万鹏科技有限公司 ht t p ://w w w.j u t a s o l a r .c o m 科技有限公司 t a s o l a r .c o mMPPT2024Z 太阳能充放电控制器使用手册 版本V1.1尊敬的用户： 非常感谢您选用我们公司的产品！我们将为您的太阳能发电系统提供长久可靠的服务！ 该手册提供产品的安装、使用、维护等相关的指导，使用前请仔细阅读该手册。

风光互补+LED 恒流一体机使用说明书■ 主要特点：1、本公司自主研发新型风光互补降压型MPPT + LED 升压型恒流一体机控制器；2、具有蓄电池浮充、涓充、过充、过放、反接保护；风机电子卸荷、转速检测、自动刹车、手动刹车保护；负载恒流输出、降功率调节、电子短路、过载保护；太阳能独特的防反接、防反充保护等全自动控制；以上保护均不损坏任何部件。

3、风力发电机采用独特的降压型MPPT 功能，具有转速检测、过速保护，风机过充自动卸荷、恒压、限流充电功能；风机转速和刹车恢复时间都可随意设定、修改；4、太阳能也采用了降压型MPPT 功能，串联式充电主回路，使充电回路的电压损失较使用二极管的充电电路降低近一半，充电效率较非PWM 高3%-6%，增加了用电时间；过放恢复的提升充电，正常的直充，浮充自动控制方式使系统有更长的使用寿命；同时具有高精度温度补偿。

5、负载使用升压型恒流方式，转换效率可达98%，可在线调整LED 输出电流，电流从30mA —3300mA 可调，并且可分四个时段，分别对亮灯时控、功率进行调节。

6、直观的LED 发光管指示当前系统运行状态，通过指示灯可以清楚的了解系统使用情况，以及故障报警状态。

7、所有控制全部采用工业级芯片，能在寒冷、高温、潮湿环境运行自如。

同时使用了晶振定时控制，定时控制精确。

8、使用了直观的LED 数码管显示设置，一键式操作即可完成所有设置，定时时间与数码管显示数字一一对应,显示更直观。

9、外壳防水采用独特的结构设计，使得外壳与散热片之间密封结合，只需将端子一面朝下安装，皆可起到安全的防水效果，顶端有安装挂件孔，即方便了安装，也起到了防水作用，同时大型散热片更加达到良好的散热效果，可有效延长控制器的使用寿命。

■ 控制器面板图:■ 系统说明：本控制器专为风力发电和太阳能发电直流供电系统、LED 照明设备设计专用，使用了专业电脑芯片的智能化控制。

采用一键式轻触开关，可完成所有操作及设置。

SOLAR KITA SUSTAINABLE BATTERY CHARGING GEAR User ManualWSBC-50Contents1. General Information (1)1.1 Key Design Features (1)1.2 Warnings (2)2. Components and accessories (3)2.1 Accessories (3)3. Specifications (4)3.1 Module electrical specifications (4)3.2 Module mechanical specifications (4)3.3 Charge controller specifications (4)3.4 Rooftop box specifications (5)4. Packaging information (6)5. Installation (7)5.1 Wiring guidelines (7)5.2 Kit fixation guidelines (8)6. Operating Instructions (9)6.1 Charge controller (9)6.2 Features of charge controller (9)6.3 Display symbols (9)6.4 Special Instructions (10)7. Troubleshooting (10)8. Frequently Asked Questions (11)9. Limited Warranty (11)User manual – Ceyone solar kit1.General InformationPlease read this user manual carefully before using the product.Dear Customer,Thank you for purchasing Ceyone solar kit.We hope that you get best results from our product which has been manufactured with high quality and state of the art technology. Please read this entire user manual and all its accompanying documents carefully before using the product. Keep this manual and its accompanying documents safe/stored to refer them in the future.1.1 Key Design FeaturesSuperior product efficiencies as per international benchmarksOur high quality components are designed for best in class product durabilityMaximizes the state of charge of the battery which ensures that the lifetime ofbattery is extendedAdequate protection ensuring hazard free operationDesigned for off-grid applications1.2 WarningsPlease read all the warnings carefully before operating the product. It is necessary to understand and keep them in mind when the system is in use. Any negligence may lead to severe damage to you and your surroundings.Disconnect all the operating battery Exceeding current and voltage rating Use in presence ofponents and accessories2.1 Accessories3.Specifications3.1 Module electrical specificationsThe figure below shows the performance curve of 50Wp module under Standard Test Conditions (STC): 1000 W/m 2 irradiance, Air Mass 1.5 and 25°C cell temperature.3.2 Module mechanical specifications3.3 Charge controller specifications3.4 Rooftop box specifications3.5 Mounting kit specifications4.Packaging information1.Rooftop box2.Charge controller3.Mounting bracket & fixing ancillariesNote: These additional inclusions are kept in position by utilizing double sided tape. Exercise caution whenremoving/ detaching the accessories.5. Installation5.1 Wiring guidelinesIn order to achieve optimized output, it is recommended to that the electrical connections are made in the correct manner using 14 gauge wire. Verify that the connections are secure to ensure safe operation of the kit. It is recommended to use a 10 amp rated fuse before the battery for enhanced safety. As a precaution use properly insulated tools & appropriate PPE’s.Line Diagram Of ConnectionExterior Wiring Guide10 Amp Fuse 14 GaugeWire5.2 Kit fixation guidelinesThe following steps should be adhered to for kit installation/ fixation.1.Connecting the rooftop box: The solar panel need to be connected to the rooftop box as shown in wiringdiagram. Please use appropriate mating connectors between the inter-connecting wire(s) to ensure safe operation.2.Fixing rooftop box atop vehicle: The rooftop box should be fixed atop the vehicle. It is recommended touse appropriate sealant & dispenser for this operation. Kindly allow the sealant to dry for minimum of 6~8 hours in a moisture free environment to obtain a permanent bond.3.Fixing the mounting structure on solar module: Use the 4 mounting clamps and fix each of themalongside the mounting hole as provided in the rear side of the module.4.Fixing ancillaries: Follow the mounting process by utilizing M6 bolt, M6 split lock washer, M6 flat washeron one side of the mounting clamp Lock the bolt by in position by utilizing M6 flat washer and M6 nut on the other side. Use appropriate tools like Spanner, Plier, etc. for obtaining a perfect fit. Connecting the rooftop box Fixing rooftop box atop vehicleModule fixation guide Mounting kit fixation guide6.Operating Instructions6.1 Charge controllerBefore making initial connections, please ensure thatthe battery has enough charge or is at adequatevoltage level such that the controller can sense thebattery.The controller is only suitable for LEAD ACIDBATTERIES: OPEN, AGM, and GEL type. It is notsuited for nickel metal hydride, lithium ions or otherbatteries. Charge controller is only suitable ofcontrolling solar PV modules as input. Never connectanother charging source to the charge controller.6.2 Features of charge controller1.The PMW charge controller is IP 68 with built-in open circuit and reverse protection2.It is equipped with dual mosfet for reverse current and low heat protection3.It has enhanced size of display for clearly observing and recording the dataDisplay the battery voltageIndication that the solar panel is charging the batteryDisplays the battery state of chargeonce its voltage is above 12.6V6.4 Special Instructions3.To obtain maximum output it is suggested that the panel’s direction is adjusted such that it faces the sun.4.Locate a clear sunlit area, free from overhanging branches, wires or obstructions to ensure maximumgeneration5.Broken modules cannot be repaired and contact with any module surface or frame can lead to electricalshock. Do NOT use a module with broken glass or torn substrate6.Do not disassemble the modules or remove any part of the module7.Do not drop Module or allow objects to fall on the Module. Do not stand or step on the Module8.Ensure the battery clamps/ connectors do not come in contact with one another to avoid short circuiting9.Ensure that all the electrical connections are secured before using the kit. Verify that the battery is beingcharged by the kit10.V erify the tightness of mechanical connections before using the kit11.P lease connect any type of load via the battery only7.TroubleshootingThe common problems are listed below. For any additional technical support, please get in touch with the local sales coordinator.1)PV Array Short CircuitIn case of array short circuit, check all the interconnections. In case of fault, immediately disconnect the faulty connection. Please take help of local sales coordinator if you find it difficult to repair the fault.2)Load Short CircuitCheck the continuity of fuse placed before battery. If blown, replace the faulty fuse and the faulty wire as necessary.3)Battery Reverse PolarityThe controller has protection against battery reverse polarity. It is however suggested to immediately correct the wiring to prevent any mishap.4)Overheating ProtectionIf the temperature of the controller heat sink exceeds 85 °C, the controller will automatically start overheating protection. However in case the system temperature rises, please keep in cool place such that its temperature drops before re-using it.5)High Voltage TransientsIf you are using this system in lightning prone areas, it is suggested that additional externalsuppression (such as using the system in range of lightening arrestor, etc.) is used.Question 1: Can the kit charge two or more 12 V batteries connected in parallel?Answer: Yes, it is possible if the batteries have the same type & capacity and are wired in parallel as a single 12V battery bank.Question 2: Is there any risk that the solar kit will over charge my battery?Answer: One of the functions of the solar charge controller is to ensure that your battery is not over charged. Question 3: Do I need to clean the solar panels?Answer: Yes, it is recommended for better performance. Dust and dirt should first be swept off the panel surface using a soft brush. When the sweeping is complete, use a wet cloth to wipe the panel surface to remove remaining dirt and/or stains.Question 4: Can I place my solar panels anywhere?Answer: To maximize generation, ensure that the tilt angle of system resembles the latitude of the place. If this is not possible, kindly ensure that the module is facing the sun and receives maximum irradiation. Further the solar module should not be operated under shadow.9.Limited WarrantyThe solar module of the kit has a 5 years of limited warranty and 10 years of power output warranty. The controller & rooftop box comes with a 1 year limited warranty. This warranty is valid against defects in materials and workmanship. It is not valid against defects resulting from, but not limited to:•Misuse and/or abuse, neglect or accident.•Improper installation, including but not limited to, improper environmental protection and improper hook-up•Damage in handling, including damage encountered during shipment or installation•Acts of God, including lightning, floods, earthquakes, fire, high winds, etc.•Exceeding the unit’s design limitNote:1.Warranty would stand void for module(s) whose type or serial numbers appears to be changed, erased,removed, illegible or in any manner altered or tampered.2.This warranty does not cover any cost associate with on-site labour and any cost associated with theinstallation, removal, reinstallation, shipping or transportation of the kit(s), any customs clearance or any other cost of return or re-shipment of kit(s).3.Any damages caused by abrasion, artificial damage or animals are exempt from this warranty.4.Defects and/or failures caused by unauthorized maintenance, operation or modification regardless ofwhether such act is wilful misconduct or negligence are exempted from warranty。

太阳能充电器说明书规格参数太阳能输出: 5V/2400mA（阳光充足下）输入：5V/2A 输出：5V/3A（max）功能指示1 外接太阳能充电器并接输入端口2 太阳能充电指示灯3 USB输出端口4 大功率单晶硅太阳能板5 挂绳孔批准：审核：编制：产品简介· 本产品为户外便携式太阳能充电包，小巧玲珑，方便携带。

配备6片大功率的单晶硅太阳能板，高达 20％ 的转换率，输出电流高达2400mA, 为您的手机、IPAD或其他小设备充电。

在享受大自然阳光的同时为您提供源源不断的绿色能源，是您外出旅游出行的必备佳品。

为设备充电1、在有阳光的地方打开太阳能产品，使太阳能板接受太阳的45°照射，太阳能指示灯绿灯亮，这时USB输出可以输出高达5V/2.4A的电流为您的电子产品进行充电。

2、为获得更大的电流，此产品可以两个并联使用，并联后可以获得最大5V/3A的电流，实现快速充电。

温馨提示：本产品需要在阳光下使用。

本太阳能面板不能直接存储电源，如果您想存储电源，您可以使用它为移动电源充电。

如果产品不能工作，请检查 USB 接口是否正确插入太阳能面板。

工作后请记住，卸下USB插头。

12345User manualSpecification parameterSolar charging :5V/2400mA(In full sunshine)Input :5V/2AOutput :5V/3A （max ）批准：审核：编制：·Product introduction·The product is an outdoor portable solar chager, small and exquisite, easy to carry. Equipped with 6 high-power mono-crystalline silicon solar panels, high transmit efficiency 20%, up to 2400mA max charging current, It can charge mobile phone ，IPAD or other small mobile devices. It willprovide you with green energy while enjoying the natural sunshine ,which will be your travelnecessity.Charger the device1、Open the solar energy product in a place with sunlight, so that the solar panel receives 45° illumina-tion from the sun, the solar indicator is green, and the USB output can up to 5V/2.4A to charge your electronic products.2、For more current , It can be used in parallel for two or three products. After parallel ,the maximum current output : 5V/3A can be obtained to achieve fast charging.Tips: This product needs to be used in the sun. This solar panel cannot store power directly. If you want to store power, you can use it to charge mobile power. If the product does not work, check that the USB connector is properly inserted into the solar panel. Remember to remove the USB plug after work.Function indication1.External solar charger connected to the input port2.Solar charging indicatorB output port4.High power mono-crystalline silicone solar panelnyard hole12345。

SCC10APWM Solar Charge Controller Installation and Operation Manual AIMS POWER9550 Gateway DrReno, NV 89521Tel:(775)359-6703Fax:(775)359-6753Email:******************************************READ MANUAL BEFORE USING THIS PRODUCT1. PRODUCT INTRODUCTIONThis AIMS Power PWM solar charge controller is designed to charge and monitor your LiFePO4 battery to achieve a longer life cycle. It also trickle charges AGM, GEL and lead acid battery technologies. Using the latest charging technologies combined with state of charge monitoring, this product allows for optimal battery maintenance and efficient solar power monitoring. The LCD screen displays operating modes such as; state of charge, voltage, and current. The product also displays symbols for easy user interface.Integrated data logger energy meterAutomatic detection of voltage 12 or 24 VdcPWM controlAutomatic load reconnectionListed to UL 1741 & CSA 22.2 No. 107.1Adjustable charge voltage2. INSTALLATIONInstall the charge controller near the battery on a stable surface. This surface should be solid, even, dry and nonflammable. The battery cable should be as short as possible and have a cable diameter size to minimize loss, e.g. 4 mm² at 20 A and 6ft in length (16 AWG).Do not install the controller in direct sunlight.To ensure adequate airflow around the controller, allow a 4 inch clearance around the unit. The temperature at the installation site may never fall below or exceed the maximum permitted ambient temperature range.Connect the individual components to the symbols provided on the bottom of controller.Follow the following connection sequence during installation:1. Connect the battery to the charge controller - positive and negative2. Connect the solar module to the charge controller - positive and negative3. Connect the DC load to the charge controller – positive and negative (optional)The reverse order applies when uninstalling.NOTE! The automatic detection of 12V or 24V systems functions properly only if this sequence order is followed. An improper sequence order can damage the battery!*There are no user serviceable parts inside the charge controller. Do not disassemble or attempt to repair the unit. Contact manufacturer. 3. OPERATION3.1 Description of LCD symbols3.2 Description of Button Function❶Button for switching display windows ❷ Enter/exit the setting (press for 5 seconds)❶Adjust parameters up ❷ Restore factory setting in each parameter (press for 5 seconds)❶Adjust parameters down (minus) ❷ Click this button to switch the load in main displaywindow3.3 View and Set the ParametersThe controller will auto display the “battery voltage” main display once power is connected (follow correct sequence from INSTALLATION instructions. This is the main display window. Use the buttonto switch between different display windows. If the parameter can be set, press the button(>5 seconds, numbers start flashing) to enter the setting, then press the or toselect the setting, after that, press the button (>5 secs) again to exit the setting (numbers stop flashing).Battery voltage(main display)Solar panelvoltageSolar panelcharging currentHigh voltagedisconnection(HVD)Float voltageAccumulative sum ofkwh drawn by loadAccumulative sumof recharged kwhLoad dischargingcurrentLow voltagereconnection(LVR)Low voltagedisconnection(LVD)Load workingmode3.3.1 Battery voltage (main display)Displays the battery voltage measured by the controller. Also, it displays thecharge and discharge status, battery capacity.3.3.2 The load ON/OFF controlIn the main display window, click the buttonto ON/OFF the load. The buttondoesn’t have this feature in the other interface.3.3.3 Environment temperatureDisplays the ambient temperature of the controller. C3.3.4 Solar panel voltageDisplays the solar panel voltage measured by the controller.3.3.5 Solar panel charging currentDisplays the charging current from the solar panel.3.3.6 Load discharging currentDisplays the discharging current drawn by load.3.3.7 Accumulative sum of recharged AhDisplays the accumulative sum of recharged Ah from solar panel. Press the button for 5 seconds to reset the meter to 0. Even when the battery isdisconnected the value remains. When 9999Ah are reached, it will switch backto 0 Ah.3.3.8 DC load consumptionDisplays the accumulative sum of Ah drawn by the DC load. Press the button for 5 seconds to reset the meter to 0. Even whenbattery is disconnected the value remains. When 9999Ah are reached, it willswitch back to 0 Ah.3.3.9 High voltage disconnection (HVD) Float voltage - ADJUSTABLE Displays the float voltage, when battery voltage reaches float voltage, the controller will start PWM control to keep the battery voltage at same level. Press the button (>5 seconds, numbers start flashing) to enter thesetting, then press theorto select the setting. Press the buttonagain to exit the setting (numbers stop flashing).3.3.10 Low voltage reconnection (LVR) - ADJUSTABLEDisplays the values for the LVR voltage. Under the LVD protection in the controller, when battery voltage is restored to higher voltage than LVR voltage, the controller will re-connect the load circuit. Press the button (>5 seconds, numbers start flashing) to enter thesetting, then press theorto select the setting. Press the buttonagain to exit the setting (numbers stop flashing).3.3.12 DC Load operating mode - ADJUSTABLEAs shown on the right, it displays the load operating mode. Different values represent different working modes.24h - normal mode, there is always output unless the battery voltage is too low.1-23h - light control with time control mode. Load will turn on after dusk and turn off according to the timer setting.0h - light control mode, load will turn on after dusk and turn on before dawn.Press on the button(>5 seconds, numbers start flashing) to enter thesetting, then press theor to select the setting. Press the buttonagain (>5 secs) to exit the setting (numbers stop flashing).4. COMMON FAULT AND HANDLING4.1 LVD Protection resolutionScreen display as shown in the figure that the battery drops below the LVD protection voltage. The controller has entered the LCD protection state, load circuit has been disconnected. Use the solar panels to recharge the battery or charger when the battery voltage reaches LVR voltage, the controller will resume the load power supply after battery reaches normal working state.4.2 Over load Protection fault resolutionScreen display (see the figure) and flashing shows over load circuit current For 60 seconds at more than 1.5 times the rated current.Overload protection state. After reducing the load, press the buttonto restore power to the load.4.3 Short Circuit Protection fault resolutionScreen display (see the figure on the right) and flashing shows there is a short circuit on the load circuit. The controller has entered into Short Circuit Protection State. Check the load for damage to the wiring circuit.After troubleshooting and correcting short circuit quick press buttonto enable the load.4.4 Solar Panel Fault resolutionSymbol flashing indicates that the controller has not detected the solar panels within 24hours. Check connection from solar panel to charge controller. Also, check if there is an open circuit between solar panel with controller. 4.5 Load Shock Fault Open load if theflashing, this indicate the load current is more than twice rated current of thecontroller. This will cause the controller to reset several times.5. WARRANTYAIMS Power offers a 2 year limited warranty.The following cases are not covered under warranty.1. DC reverse polarityThe charger is NOT designed with DC reverse polarity protection. A reverse polarity may severely damage the inverter.2. Incorrect DC wiring3. Operation in a moist environmentAIMS Power Warranty Instructions:This product is designed using the most modern digital technology and under very strict quality control and testing guide lines.If,howeveryoufeelthisproductisnotperformingasitshould,pleasecontactus:**************************(775)359-6703.We will do our best to resolve your concerns. If the product needs repair or replacement, make sure to keep your receipt/invoice, as that will need to be sent back along with the package and RA# prepaid to AIMS. You have a limited 2 year from date of purchase warranty.This warranty is valid worldwide with the exception that freight and duty charges incurred outside the contiguous 48 United States will be prepaid by customer.Except as provided above, AIMS makes no warranty of any kind, express or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose. In no event shall AIMS be liable for indirect, special or consequential damages. This warranty only applies to AIMS Power branded products. All other name brand products are warranted by and according to their respective manufacturer. Please do not attempt to return non-AIMS Power branded products to AIMS Power.For additional products such as:- Modified sine wave inverters- Pure sine wave inverters- Solar charge controllers- Generators- Inverter chargers with automatic transfer switches- Custom cut cables- Batteries- Solar panelsPlease visit our web site: Tofindoutwheretobuyanyofourproducts,youmayalsoe-mail:************************(775)359-6703.6. TECHNICAL DATASHEETModelSCC10A PWMRated current10ARated voltage 12/24VMax solar voltage<50V(12/24V) Low voltage disconnect 10.7/21.4V Low voltage reconnect 12.6/25.2V Float charge 13.7/27.4V Standby loss <30mA Material ABS+AluminumUSB output 5V/2A Charging mode PWM Temp compensation -4mV/Cell/℃ Operating condition-20℃ to 60℃ | -4°F to 140°F Size/Weight6.5L”* 3.5W”* 1.5H”.5 lb。

Operating manualSolar charge controller10.10 A / 8.8 A / 6.6 APlease read these instructions completely before installation!1. About this manualThese operating instructions are part of the product. Read these operating instructions carefully before use, keep them over the entire lifetime of the product, and pass them on to any future owner or user of this product.This manual describes the installation, function, operation and maintenance of the solar charge controller. These operating instructions are intended for end customers.A technical expert must be consulted in cases of uncertainty.2. SafetyThe solar charge controller may only be used in PV systems for charging and controlling lead-acid batteries in accordance with this operating manual and the charging specifications of the battery manufacturer.The solar charge controller may only be connected to the local loads and the battery by trained personnel and in accordance with the applicable regulations. Follow the installation and operating instructions for all components of the PV system.No energy source other than a solar generator may be connected to the solar charge controller. Follow the general and national safety and accident prevention regulations.Keep children away from PV systems. Do not use the solar charge controller in dusty environments, in the vicinity of solvents or where inflammable gases and vapours can occur. No open fires, flames or sparks in the vicinity of the batteries. Ensure that the room is adequately ventilated. Check the charging process regularly.Follow the charging instructions of the battery manufacturer. Battery Acid splashes on skin or clothing should be immediately rinse with plenty of water. Seek medical advice.Do not operate the solar charge controller when it does not appear to function at all. The solar charge controller or connected cables are visibly damaged or loose. In these cases immediately remove the solar charge controller from the solar modules and battery.3. FunctionsThe solar charge controller monitors the state of charge of the battery bank, controls the charging process, controls the connection/disconnection of loads. This optimises battery use and significantly extends its service life.The following protection functions are part of the basic function of the controller: Overcharge protection ; Deep discharge protection ; Battery undervoltage protection ; Solar module reverse current protection.4. Installation4.1 Mounting location requirementsDo not mount the solar charge controller outdoors or in wet rooms. Do not subject the solar charge controller to direct sunshine or other sources of heat. Protect the solar charge controller from dirt and moisture.Mount upright on the wall (concrete) on a non-flammable substrate. Maintain a minimum clearance of 10 cm below and around the device to ensure unhindered air circulation. Mount the solar charge controller as close as possible to the batteries (with a safety clearance of at least 30 cm).4.2 Fastening the solar charge controllerMark the position of the solar charge controller fastening holes on the wall.Drill 4 Ø 6 mm holes and insert dowels. Fasten the solar charge controller to the wall with the cable openings facing downwards, using 4 oval head screws M4x40 (DIN 7996).4.3 ConnectionUse an wire size suited to the current ratings of the charge controller, e.g. 6mm² for 10A, 5 mm² for 8A, 4 mm² for 6A, 3 mm² for 5A for cable length of 10 m.An additional external 20A fuse (not provided) must be connected to the battery connection cable, close to the battery pole. The external fuse prevents cable short circuits.Solar modules generate electricity under incident light. The full voltage is present, even when the incident light levels are low. Protect the solar modules from incident light during installation, e.g. cover them.Never touch not isolated cable ends. Use only insulated tools. Ensure that all loads to be connected are switched off. If necessary, remove the fuse.Connections must always be made in the sequence described below.1st step: Connect the batteryConnect the battery connection cable with thecorrect polarity to the middle pair of terminalson the solar charge controller (with the batterysymbol).If present, remove any external fuse. Connectbattery connection cable A+ to the positivepole of the battery. Connect batteryconnection cable A– to the negative pole ofthe battery. Insert the external fuse in thebattery connection cable.If the connection polarity is correct, the infoLED illuminates green.2nd step: Connect the solar moduleEnsure that the solar module is protected from incident light (cover it or wait for night).Ensure that the solar module does not exceed the maximum permissible input current.First connect the M+ solar module connection cable to the correct pole of the left pair ofterminals on the solar charge controller (with the solar module symbol), then connect theM– cable. Remove the covering from the solar module.3rd step: Connect loadsFirst connect the L+ load cable to the correct pole of the right pair of terminals on the solarcharge controller (with the lamp symbol), then connect the L– cable. Insert the load fuse orswitch on the load.Notes : Connect loads that must not be deactivated by the solar charge controller deepdischarge protection, e.g. emergency lights or radio connection, directly to the battery.Loads with a higher current consumption than the device output can be directly connectedto the battery. However, the solar charge controller deep discharge protection will no longerintervene. Loads connected in this manner must also be separately fused.4th step: Final workFasten all cables with strain relief in the direct vicinity of the solar charge controller(clearance of approx. 10 cm).5. LED displaysLED Status Meaningilluminates green normal operationInfo LEDflashes slowly red* system fault- too high charging current- overload / short circuit- overheatedtogether with red LED :- too low battery voltagetogether with green LED :- too high battery voltageflashing quickly* battery empty, low voltage disconnectionprewarning, loads still onBatteryredLED flashing slowly* deep discharge protection active (LVD), loadsdisconnectedilluminates battery weak, loads are onBatteryyellowLEDflashes slowly yellow* LVD reconnection setpoint has not yet beenreached, loads still disconnectedilluminates battery goodBatterygreenLEDflashes quickly green* battery full, charge regulation active*flashing slowly: 0,4Hz: 4 times in 10 second, flashing quickly: 3Hz: 3 times in 1 second6. GroundingThe components in stand-alone systems do not have to be grounded – this is not standardpractice or may be prohibited by national regulations (e.g.: DIN 57100 Part 410: Prohibitionof grounding protective low voltage circuits). Ask your dealer for technical assistance.7. Lightning protectionIn systems subjected to an increased risk of overvoltage damage, we recommendinstalling additional lightning protection / overvoltage protection to reduce dropouts.Ask your dealer for technical assistance.8. MaintenanceThe solar charge controller is maintenance-free.All components of the PV system must be checked at least annually, according to thespecifications of the respective manufacturers. Ensure adequate ventilation of the coolingelement. Check the cable strain relief. Check that all cable connections are secure. Tightenscrews if necessary. Check corrosion on terminals.9. Faults and remediesNo display : Check battery polarity and external fuse. Or battery voltage is too low orbattery defective.Battery is not charged : Check if solar modul is connected with correct polarity or if shortcircuit at the solar input. If solar module voltage is lower than battery voltage or if solarmodule is defective the battery cannot be charged.Battery displays jumps quickly : Battery voltage changes quickly. Large pulse currentscause voltage fluctuation. Battery is too small or defective. Ask your dealer for technicalassistance.The following faults do not destroy the controller. After correcting the fault, the device willcontinue to operate correctly:* solar module short circuits * reverse solar module polarity *2* short circuits at load output * excessive load current* reversed battery polarity *1* solar module overcurrent* device overtemperature * overvoltage at the load output10. Legal guaranteeAccording to the German legal requirements, for this product the customer has a 2 yearlegal guarantee.The seller will remove all manufacturing and material faults that occur in the product duringthe legal guarantee period and affect the correct functioning of the product. Natural wearand tear does not constitute a malfunction.Legal guarantee does not apply if the fault can be attributed to third parties, unprofessionalinstallation or commissioning, incorrect or negligent handling, improper transport, excessiveloading, use of improper equipment, faulty construction work, unsuitable constructionlocation or improper operation or use.Legal guarantee claims shall only be accepted if notification of the fault is providedimmediately after it is discovered. Legal guarantee claims are to be directed to the seller.The seller must be informed before legal guarantee claims are processed.For processing a legal guarantee claim an exact fault description and the invoice / deliverynote must be provided. The seller can choose to fulfil the legal guarantee either by repair orreplacement.If the product can neither be repaired nor replaced, or if this does not occur within asuitable period in spite of the specification of an extension period in writing by thecustomer, the reduction in value caused by the fault shall be replaced, or, if this is notsufficient taking the interests of the end customer into consideration, the contract iscancelled. Any further claims against the seller based on this legal guarantee obligation, inparticular claims for damages due to lost profit, loss-of-use or indirect damages areexcluded, unless liability is obligatory by German law.11. Technical DataSteca Solsum F 6.6F 8.8F 10.10FSystem voltage 12 V (24 V)Own consumption < 4 mADC input sideOpen circuit voltage solar module(at minimum operating temperature)< 47 VModule current 6 A 8 A 10 ADC output sideLoad current 6 A 8 A 10 AEnd of charge voltage 13.9 V (27.8 V)Boost charge voltage 14.4 V (28.8 V)Reconnection voltage (SOC / LVR) *³> 50 % / 12.4 V … 12.7 V(24.8 V … 25.4 V)Deep discharge protection (SOC / LVD) *³< 30 % / 11.2 V … 11.6 V(22.4 V … 23.2 V)Operating conditionsAmbient temperature -25 °C … +50 °CFitting and constructionTerminal (fine / single wire) 4 mm2 / 6 mm2 - AWG 12 / 9Degree of protection IP 32Dimensions (X x Y x Z) 145 x 100 x 24 mmWeight approx. 150 g*1Solsum is protected against reverse battery polarity together with polarity protectedloads. Reverse battery polarity combined with short circuited or polarised load couldcause damages in load or regulator*2Avoid reverse module polarity in a 24V system*3Lower value for nominal current, higher value for lowest currentInfo LED Battery LEDsManufactured in aDIN EN ISO 9001:2000 facilitySolsum / Z02 / Version 1104/ 730.930。

太阳能充电器使用说明书本产品是一款多功能太阳能应急充电器，内置1200mAh高容量可充电锂电池，可随时随地对您的手机、数码相机、PDA、MP3、MP4等数码产品进行充电。

造型华贵大方，小巧玲珑，携带方便，时尚高雅。

使用方法1、使用之前请给您的太阳能充电器充电，有三种方法可以选择：a、将充电器放置于太阳光直射处，太阳能将转化为电能给充电器内置可充电电池充电。

b、将充电器USB线连接电脑，此时充电器指示灯会闪光，表示正在充电，当充电满后，此灯将会熄灭。

C、用交流适配器充电，充电时指示灯会闪光，当充电满后此灯将会熄灭（因为设计有自动断电保护）2、将转换接头连接到延长线，再将延长线的另一头连接到充电器，或直接将转接头连接到充电器。

3、将转换接头连接到您的手机或其它数码产品。

4、从您的手机或其它数码产品上将可看到正在充电，充电的同时您也可以用手机通话。

5、太阳能充电指示。

将开关拨到‘NO’，太阳能板在接受阳光照射时，太阳能充电指示呈绿色。

产品特点：1、特别适用于应急场合。

当您在野外作业或旅游，或者遇到停电时，太阳能充电器将会帮您的大忙，使您的手机随时随地保持工作状态，让您不间断的与您的朋友和家人保持联系。

2、使用方便无论何时何地，您都可以极为方便的给您的手机或其它数码产品充电。

3、高效率充电给您的手机充电60分钟，可以获得100-150分钟通话时间4、环保、节约能源使用绿色能源太阳能，可为环保作出您的贡献。

5、外形时尚，携带方便造型简洁华贵，超薄不锈钢外壳设计，小巧玲珑，携带方便。

6、使用安全带有充电过充保护，有效延长您的手机电池的使用寿命，使用安全。

产品规格1、使用高转换效单晶硅或多晶硅片，太阳能转换效率高达15%以上。

2、太阳能电池板规格：5.5V/80mA。

3、充电时内置高容量可充电锂电池：1200 mAh。

4、输出电压：5.5V。

5、输出电流：1000mA。

6、充电器给手机充电时间：约60分钟（不同品牌和型号的手机有少许差别）。

太阳能充电器使用说明太阳能移动电源系列产品，拥有智能调压专利技术，可以调节不同的输出电压及电流。

可以在太阳光下对各类手机或USB接口数码产品直接充电，也可以在太阳光较弱或无阳光条件下通过内置蓄电池放电对手机或USB接口数码产品充电。

适用于出差、旅游、长途乘车船、野外作业等环境的备用电源，具有安全保护、兼容性好，大容量、体积小、使用寿命长、性价比高。

产品规格：1、太阳能硅板峰值功率：1.54W2、工作电压：5.5V(最大)3、充电电流：280mA4、蓄电池容量：2000mAh5、输出电压：4.5～9V(可调)6、输出电流：1A(最大)7、充电时间：8-10hrs(幅照度：100mW/C㎡) 3-4hrs(室内电源：5V/500mA)充电说明：1、在xx下充电充电时，放电开关应置于OFF位置，以免充电缓慢，展开太阳能板放置阳光下，并正射太阳能板．太阳能充电器的Light1灯变为红色，此时光能转化为电能对太阳能充电器电池蓄存电．红色表明内置锂电池蓄存电能不多，如果Light1灯变为橙色，表明锂电池中蓄存电能较高，且电压在3.8V～4.1V．如果Light1灯变为绿色，证明充电器内置电池蓄存电已经饱和．当您合上太阳能面板时Light1灯将熄灭，太阳能面板停止充电．注：如果展开太阳能板，在日光下Light1灯变为红色或橙色时，只是表明太阳能面板电压达到Light1灯亮，而不能证明太阳能板在充电．2、使用AC充电由于没有太阳光或阴天情况下，该用AC充电器的DC头连接太阳能充电器的DC接口．再将AC充电器插入110V或220V交流电，Light1灯将变为红色再由红色变为橙色再到绿色的过程．Light1灯变为绿色．表明内置电池已充满，并断开AC充电器的连接．放电说明：放电时，并将输出电压档位调到适当的电压对充电产品充电，然后根据你需要移动设备选择合适的转接头，也可以用USB插头对数码产品连接一起．并将开关切换到＂ON＂Light1与Light2同时亮时，Light2亮时表示开始放电，（此时内置电池已充满Light1出现红绿交替闪烁属正常现象，具体参考Light1显示说明），当你外接移动设备充电时，Light2亮时，表明正在对你的移动设备或手机充电，移动设备或手机充满后，请将开关切换到OFF位置，以免电量流失．应用领域：适用于充电电压在4.5～9V移动通讯、数码注意事项：１、强光下不能间段充电（直射太阳能面板）约8小时，可充满内置电池．２、在夏季时请勿将充电器置于车内（车内温度过高）．影响电池使用寿命３、请勿隔着玻璃对本充电器进行充电．充电效果差．４、必须在强光下充电，在弱光下（Light１）亮灯，只能代表检测到有光，并非代表已在充电（如在室内照明灯下）．所以请勿在弱光下进行充电．５、由于出厂时，每个充电器内所含电量不一致，所以，初次使用充电或放电的时间会不同．６、请勿使用有腐蚀性溶液擦拭本机，以免损害本产品．7、严禁将此产品投入火中，以免引起爆炸。

太阳能充电器使用说明书1、2、3、4、5、6、7、8、9、101112131.1 利用太阳能或交流电源可直接给外接电器使用及充电，或对本产品内的畜电池充电。

1.2 配有高亮照明，标准的USB端口输出，可供MP3、MP4、手机、PDA、数码相机等USB产品直接使用或充电。

1.3 本充电器的蓄电池充电时，具备稳压、恒流、过充电和过放电的保护功能。

1.4 配置充电状态指示及蓄电池电量检测功能。

二、特点：2.1 轻便、环保，实用性强，尤其便于户外或野外应急供电与充电。

2.2 当手机没有电量的情况时，放在阳光的照射下，太阳能充电器所发出的电量可直接供手机通话使用。

2.3 3-5小时即可对市面上的手机充满电。

2.4 配有液晶显示屏，用电量检测按钮可查看充电状态和蓄电池电量。

三、技术规格：3.1整机：①产品尺寸：113X55X26.5mm。

②重量：约165g。

③输出功率：5W。

④工作参数：A. 用太阳能对蓄电池充电,7-9小时可充满。

B. 用交流电源适配器对本机蓄电池充电，3小时可充满。

C. 蓄电池充满电量后可连续照明工作48小时。

D. 用太阳能直接对手机进行充电，3-5小时可充满。

E. 蓄电池满电时, 3-5小时可对手机充满电。

F. 交流电源适配器参数：AC100-240V，50-60Hz。

DC输出5.3V，500mA。

G. 内用蓄电池参数：3.7V，1200mAh安全环保锂离子蓄电池。

H. 太阳能光伏电池参数：DC6V，160mA。

四、使用说明：4.1 蓄电池电量检测：按电量检测键，如图（1）所示,液晶显示屏会显示蓄电池电量。

4.2 照明功能：如图（2）所示,再将转换开关置于（）。

4.3 用本充电器的蓄电池给外接电器供电使用或充电时：将适配头插入手机或其他电器接口，另一端插入本充电器USB插孔（如图5所示），再将转换开关置于()此图标。

4.4 用交流电源给蓄电池充电时：应先将交流电源插头插入（本说明书所设定），其电压允许范围内的交流电插座，另一端插入本充电器输入插孔，再将转换开关置，于（）位置，如图（6）所示。

太阳能-市电双电源充电器说明书一. 太阳能-市电双电源充电器原理框图二. 接线1. 双电源供电，互相隔离。

分别是市电3相380V AC ，和太阳能电源108V ，40A 。

三相市电接至机柜上方的断路器。

太阳能电源接至机柜中部的太阳能电源接线端子。

2. 输出接锂电池。

充电电压最高584V ，电流最大5.0A 。

接至机柜中部的充电输出端子。

注意正负极不能接反。

3. 配有CAN 总线通讯功能。

通讯协议见第七节 通讯。

接至机柜中部的CAN 通讯端子。

三. 操作面板四. 人工操作1. 只使用太阳能电源。

按“太阳能启动”按钮，太阳能电源投入，启动升压器。

“太阳能电源”指示灯亮，液晶随即点亮。

按“启动/停止”键，开始充电。

2. 只使用市电。

接通市电后“太阳能启动”按钮自动失效，太阳能电源不能投入使用。

接入市电后，液晶点亮，按“启动/停止”键，开始充电。

3.充电器内部自动控制，保证双电源互锁，不会同时工作。

4.在使用太阳能电源时，接入市电，升压器会自动停机切除。

5.断开市电后，液晶关闭；如果在充电中则充电停止。

然后手动按“太阳能启动”按钮，启动升压器，使其工作。

此时液晶重新点亮，充电器可以投入工作。

五. 液晶显示液晶第一行显示充电输出电压、电流，液晶第二行显示充电状态，液晶第三行显示充电进行时间，液晶第四行显示正在使用的电源，是太阳能或是市电。

未接入市电时，显示太阳能电源电压。

如果有通讯故障，则会显示通讯故障。

六. 设定菜单1.浮充电压值400V-584V，出厂默认值580V2.恒流电流值0.5A-5.0A，出厂默认值5.0A3.均充电压值400V-584V，出厂默认值580V4.转浮充电流值0.1A-5.0A，出厂默认值0.2A5.浮充延时0-8小时，或者不停机。

6.过压保护值420V-624V，出厂默认值600V7.均衡充电周期3-30天，出厂默认值20天8.电瓶类型铅酸免维护电池。

9.光伏不足停机60.0V-110.0V，出厂默认值90.0V当光伏板输出电压低于此设定值时，充电器自动停机。

■ 特性:T N -1500系列具太阳能充电功能1500W 正弦波D C -A C 逆变器‧纯正弦波输出(THD<3%)‧瞬间功率高达3000W‧ UPS 模式,可选择待机节能模式‧效率高达91%‧电源启动-关闭开关‧可选择待机节能模式‧面板显示操作状态‧恒温控制直流冷却风扇‧保护种类：电池低压警报/电池低压关机/输出短路/ 交流断路/过负载/过电压/过温度/输入反接保护‧应用：家电，电动工具，办公和便携式设备 车辆和游艇等。

‧具有太阳能/交流充电器‧支援RS-232通讯(包含通讯线RJ11-RS232)备注7‧ 3年保固E 13TPTC004IEC62368-1UL458搜寻 ■ 全球交易品项识别码图 21. 设置：调整输出电压，充电电压，频率和操作方式的调整,详情请参照图3。

2. 统计：计算每个工作模式于工作期间的百分比，详情请参照图4。

3. 遥控关机：可远程遥控电源开关机。

4. 暂停：停止刷新监控软件页面。

Setting Solar Charge123456INVERTERAC Charge10010000Battery Voltage O/P Voltage Internal Temperature By passTN-1500-143Utility Voltage Start Date Reset Date O/P Frequency Power on Remote off Battery low Battery used upStand by saving mode Abnormal ShutdownBatteryLoading54.111010.00.02007/12/07 03:13:33 PM 2007/12/21 01:40:56 PM60.0 VV ℃VHzAC InStatistics R.C. Power off Pause ExitTN-1500系列具太阳能充电功能1500W 正弦波DC-AC 逆变器。

太阳能手机充电器使用说明书●概述本充电器利用太阳能电池板吸收阳光，转换成电；它可以给市面上的所有手机充电，还可以给数码相机、手机等产品充电，并有户外超白光LED灯功能。

●工作原理：在太阳光下，通过控制电路将光电池产生的电源存储到内置蓄电池，也可以直接把光电池产生的电源对手机或数码产品充电。

●使用方法：1.光电池对手机直接充电：打开翻盖放置阳光下照射即可充电。

2.太阳能充电器前三次使用要充分循环充电和放电，这样才能有效激活其内置蓄电池容量。

a.使用家用电源充电，前三次充电时间要达到12小时以上。

b.前三次要充分放完太阳能内置蓄电池电量后才能充电。

3.内置蓄电池对手机充电，手机接孔2，开关置充电端（CH端），LED2为红色表示正在充电，绿色表示手机电池已经充满。

4.家用电源对内置蓄电池充电：外接直流电源接插孔1，LED为红色表示正在充电，为绿色表示充电已经完成。

5.LED灯：当开关置LED灯端，即可用“户外超白光LED灯”功能。

LED灯（户外超白光LED灯）IN下插孔（外接家用电源充电插孔）IN右边指示灯（蓄电池充电指示灯）OUT下插孔（输入手机充电插孔）OUT右边指示灯（手机充电工作指示灯）开关（双掷开关，LED端为LED灯控制，CH端为手机充电工作控制）●使用注意事项：（1）使用本产品之前请先对蓄电池充电，可以通过家用电源充电或阳光照射电池。

（2）不要在火源附近的场所中使用（3）内置蓄电池充足电只作旅行、出差、或外勤工作没有阳光时应急充电之用。

（4）不要把产品投入水中，也不要弄湿内置蓄电池和电器元件。

（5）不要用金属导体短路电池输出正负极。

（6）不要拆卸或解剖产品内部部件，若有损坏厂家不执行承保规定。

（7）本产品还备有家用电源充电器，如需对内置蓄电池应急充电，只需将所配直流充电器接通100V~240V 交流电源，这时内置蓄电池将得到快速充电。

（8）在使用之前请详细阅读使用说明书。

不适当操作可能引起内置电池和电器元件损坏或电池容量衰减。

太阳能智能充电控制器使用说明书一、型号说明二、主要特点1. 12V/24V 系统电压自动识别。

2. 使用抗干扰能力极强的微处理器和专用控制程序，控制器稳定可靠。

3. 改进三段式充电算法，每周期对蓄电池进行一次均衡充电，有效地防止蓄电池不均衡和硫化现象，提高蓄电池使用寿命。

4. 具有红外通信功能。

用户可通过管理软件查询控制器的运行状态，并可以对控制器的各种运行参数进行设置，如：◆可对各路负载输出功率进行三段式独立设定，以达到省电的效果；◆设置开关灯的光照度；◆可查询当前控制器的工作状态和故障情况；5. 丰富的负载工作模式，方便使用在各种路灯及监控设备上。

6. 外置温度传感器，具有高精度温度补偿。

7. 参数设置掉电保存功能，无需重复设置，使用方便快捷。

8. 完善的保护功能：◆极性反接保护：能够对太阳能板或蓄电池极性反接进行保护；◆过载保护：1.25倍额定电流30秒，1.5倍额定电流5秒过载保护，≥3倍额定电流立即保护，自动解除保护的时间可设置。

◆雷电保护：控制器内部设置防雷器件，在多雷区使用可以有效地保护控制器；◆防水/尘保护：防护等级IP68 在恶劣环境下仍能正常工作；◆蓄电池过放电保护：避免电池过放损坏蓄电池，低压/欠压保护值可通过软件设定。

三、安装和接线1. 控制器安装要牢靠，尺寸如下：外形尺寸：100×80×23(mm)安装尺寸：73×50(mm)安装孔径：4(mm)动识别蓄电池电压后开始工作。

3.连接“+”极：控制器为共正极设计，请将蓄电池、光电池和负载的正极分别与控制器的正极端（红线）连接在一起。

4. 连接蓄电池“－”极：如果连接正确，蓄电池指示灯会点亮，否则，请检查连接是否正确。

5. 连接太阳能板“－”极：如果阳光充足，充电指示灯会亮。

6. 连接负载“－”极：将负载连接线接入控制器负载输出端，电流不能超过控制器额定电流。

接线图如下图所示：四、使用建议1. 控制器在上电后会自动识别蓄电池电压，使用时请先接蓄电池，并保证连接可靠。

太阳能充电器使用说明书欢迎您购买我们的太阳能充电器。

本说明书将为您提供详细的操作指南，帮助您充分了解和正确使用这款产品。

在使用之前，请仔细阅读本手册，并按照说明进行操作，以确保您能够充分利用这款太阳能充电器的优势。

一、产品概述1.1 太阳能充电器简介太阳能充电器是一种利用太阳能转化为电能的设备，通过太阳能电池板吸收阳光，将光能转化为电能，从而为电子设备充电。

它具有环保、方便携带等优势，适用于户外旅行、露营、徒步等活动中的各类电子产品。

1.2 产品特点- 高效能源转化：太阳能充电器采用先进的太阳能电池板技术，能够高效转化阳光能量为电能，提供稳定的电力支持。

- 多功能充电接口：本产品配备了多种充电接口，适用于不同品牌的电子设备，如手机、平板电脑、数码相机等。

- 轻便便携：太阳能充电器采用轻量化设计，便于携带和使用，适合户外活动中的充电需求。

二、使用方法2.1 充电器连接将太阳能充电器展开，确保太阳能电池板面朝向阳光，然后使用提供的连接线将充电器与电子设备连接。

2.2 充电指示灯充电器上配有LED指示灯，当太阳能充电器处于工作状态时，指示灯将点亮。

当指示灯亮起时，表示太阳能充电器可以为您的电子设备充电。

2.3 充电时间太阳能充电器的充电时间受到一系列因素的影响，例如阳光强度、充电器的位置等。

一般情况下，在阳光充足的情况下，充电时间约为4-6个小时。

2.4 安全使用提示- 在使用太阳能充电器时，请确保充电器的太阳能电池板面无任何遮挡物，以保证充电效果。

- 请避免将太阳能充电器浸入水中或接触火源，以防止发生损坏或安全事故。

- 不要将太阳能充电器暴露在高温、潮湿或恶劣的环境中，以免影响充电效果和使用寿命。

三、常见问题解答3.1 如何判断充电器是否工作正常？答：当太阳能充电器连接电子设备后，LED指示灯亮起即表示充电器正常工作。

3.2 太阳能充电器适用于哪些电子设备？答：太阳能充电器适用于各类带有USB充电接口的电子设备，如手机、平板电脑、数码相机等。

ASC48-ES Solar ChargerContentsSolar Panel Input 2DC Output 3 Environmental Requirements 3 Mechanical 4 Compliances 4 Certifications 4Technical DataIssue D June 2016ASC48-ES Solar Charger2EATON CORPORATION /telecompowerSolar Panel InputNominal operating range 100 V DC to 300V DC Start-up voltage 1100V DCMinimum operating voltage 2< 50V DC Maximum open-circuit voltage 350V DC Absolute maximum input voltage 350V DCMaximum Input Current: 11.4A (185V DC, 20°C)Efficiency:96.4% peak>95% (20 to 100% load, Vin=230V, Vout=54.5Vdc)Maximum Power Point Tracking (MPPT) Matches current draw to panel output for best power transfer Input protectionSwell Tolerance:Surge:Controller shuts down above 400V, returns to normal operation when input is within operating range. 6kV surge (varistors, gas arrestor)Input Over-current Protection:HRC fuses in positive and negative inputs Input Fuse Ratings: 16A / 250V IsolationInput to output Input to ground Output to ground4242V DC2220 V DC (Input varistors disconnected) 1000 V DCOutput Power derating with Temperature andInput Voltage (Vout = 54.5V)Maximum Output Power with Input Voltage(Ambient Temperature ≤ 60°C)12Once started, the controller will operate down to this voltage or lower.ASC48-ES Solar ChargerTechnical Data Issue D June 2016EATON CORPORATION /telecompower 3DC OutputNominal Voltage:48V Adjustable Voltage Range:43 to 57.5VConstant power output characteristic 48 – 57.5V. Load required below 45V.Rated Output Power: 2000W @ 185 – 275V (230V nominal) 1150W @ 110 – 120V (120V nominal) Preset Accuracy ±0.1V Regulation:±0.1V Constant voltage mode, AVC enabled from system controller.Default (Fail-safe) voltagesLoss of System Communication: Preset voltage:Output voltage resets to system preset voltage 54.5 ±0.1V (manufacturer preset) Hold-up Time:12msAt 80% output power and 230V input, the DC output voltage change is 54.5V to 43V.Start-up (soft start)Start up delay:Output ramp slope: (rectifier rated output, % Amps per second)Adjustable 0 to 600 seconds (factory preset: 2 seconds) Adjustable 1 to 100% per second (factory present 20% per second)ProtectionCurrent Limit:Over Temperature Turndown: Over Voltage Shutdown: Short-circuit:41.7AAutomatic power turndown. See temperature derating graphs. <3ms delayFull short-circuit protection. Output current limited to less than130% of rated output current.Rectifier will continue normal operation after short-circuit is removed. Non-urgent (Current Limit) alarm generated. NoiseRipple (<100Hz)Audio Frequency (300 Hz – 3.4 kHz): Wide band (5Hz – 1MHz): Peak to peak (0 – 20 MHz):Discrete frequency (3.4kHz – 150kHz):<20mV rms (unweighted) <2mV (psophometric) <20mV rms (unweighted) <200mV p-p (unweighted)<5mV rms (1kHz wide selective frequency) At 25o C, 54.5V outputParallel operation (ASC48-ES output only)Number of units in parallel Current sharing modeWith SC200/SC300 controllerWithout SC200/SC300Up to 12 unitsActive current sharing managed by controllerPassive, set buy solar panel and ASC48-ES output characteristics Environmental RequirementsAmbient TemperatureRated Operating Range: Extended Operating Range:-10°C to +50°C [14°F to 122°F]-40°C to +70°C [-40°F to 158°F]Output characteristics de-rate above 50°C and below -10°C [14°F]. Refer to de-rating graphs. HumidityNominal: Range:50% RH< 95% RH (non condensing) Altitude: < 3000m [9800 feet]Technical DataIssue D June 2016ASC48-ES Solar Charger4EATON CORPORATION /telecompowerMechanicalDimensions H, W, D: 3U (130mm, 5.1”), 42mm (1.6”), 266mm (10.5”) overall Weight: 1.7kg [3.7 lb] Connector: PCB EdgeRack compatibility Mounts in modified APS-3G racks 3Cooling:Temperature controlled, variable speed high reliability fan Front panel LEDs:Power on: Minor alarm: Major alarm:Green Amber Red CompliancesSafety:AS/NZS 60950.1, UL 60950-1, IEC 60950-1 EMC – immunityElectrostatic discharge: Radiated radio frequency: Electrical fast transients: Surge:Conducted radio frequency: Dips, interruptions & variations:EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11EMC – emissionsConducted emissions (AC): Conducted emissions (DC): Radiated emissions: Harmonics:Fluctuations and flicker:EN 55022 / CISPR 22 (Class B) EN 300 386 (Class A)EN 55022 / CISPR 22 (Class B) EN 61000-3-2 EN 61000-3-3CertificationsEuropeCE-mark RCM© Eaton Corporation. All Rights Reserved. In the interests of continual product improvement all specifications are subject to change without notice. Performance ratings are valid with all other variables at Nominal. Specifications guaranteed over rated operating range. Eaton, Powerware, Intergy, CellSure, SiteSure, DCTools and PowerManager are trade names, trademarks, and/or service marks of Eaton Corporation or its subsidiaries and affiliates. All other marks are the property of their respective owners.3Requires special subrack option for DC input connections.。