5-FT. DELUXE ALUMINUM CARGO CARRIERWITH 5-FT. RAMPOWNER’S MANUALWARNING:Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONSbefore operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.Thank you very much for choosing an Ultra-Tow product! For future reference, please complete the owner’s record below:Model: _______________ Purchase Date: _______________Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.This cargo carrier is designed for certain applications only. The distributor cannot be responsible for issues arising from modification. We strongly recommend this cargo carrier not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the cargo carrier until you have first contacted the distributor to determine if it can or should be performed on the product.For technical questions please call 1-800-222-5381.INTENDED USEThis cargo carrier fits in a 2in. receiver and can carry up to a 500-lb. load. It is ideal for use as a mobility carrier, a transporter for lawn equipment or to provide additional cargo space.TECHNICAL SPECIFICATIONSGENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury.CAUTION: Do not allow persons to operate or assemble this aluminum cargo carrier until they have read this manual and have developed a thorough understanding of how the hand truck works.WARNING:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.SAVE THESE INSTRUCTIONSWORK AREA• Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can causeaccidents.• Keep children and bystanders away while operating the aluminum cargo carrier. Distractionscan cause you to lose control, so visitors should remain at a safe distance from the work area.• Be aware of all power lines, electrical circuits, water pipes and other mechanical hazards inyour work area, particularly those hazards below the work surface hidden from the operator’sview that may be unintentionally contacted and may cause personal harm or property damage.• Be alert of your surroundings. Using the aluminum cargo carrier in confined work areas mayput you dangerously close to cutting tools and rotating parts.PERSONAL SAFETY• S tay alert, watch what you are doing and use common sense when using the aluminum cargocarrier. Do not use the aluminum cargo carrier while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating an aluminum cargo carrier mayresult in serious personal injury.• Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothingand gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in movingparts.• Use safety apparel and equipment. Use safety goggles or safety glasses with side shieldswhich comply with current national standards, or when needed, a face shield. Use as dust maskin dusty work conditions. This applies to all persons in the work area. Also use non-skid safetyshoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate. ALUMINUM CARGO CARRIER USE AND CARE• Do not modify the aluminum cargo carrier in any way. Unauthorized modification may impai rthe function and/or safety and could affect the life of the equipment. There are specificapplications for which the aluminum cargo carrier was designed.• Always check of damaged or worn out parts before using the aluminum cargo carrier.Broken parts will affect the aluminum cargo carrier operation. Replace or repair damaged or wornparts immediately.• Do not exceed the aluminum cargo carrier load capacity.• Distribute the load evenly. Uneven loads may cause the aluminum cargo carrier to tip, resul tingin personal injury to the operator or others. To minimize the effects of dynamic loading, makesure the load is centered on the carrier.• Use the aluminum cargo carrier on flat and level surfaces capable of supporting thealuminum cargo carrier and its maximum load. Pulling or pushing a load on a slanted or unevensurface can result in loss of control.• Prior to transporting a load, make sure the Ramp of the carrier is folded and secured. The loaditself must also be properly secured to the carrier.• Store idle the aluminum cargo carrier. When the aluminum cargo carrier is not in use, store itin a secure place out of the reach of children. Inspect it for good working condition prior tostorage and before re-use.WARNING: Flammable cargo can ignite from exposure to heat. Be aware of the possible fire risk and property damage resulting from the vehicle’s exhaust system pointing at or running near the cargo in the carrier. Do not use if this condition exists.Tools NeededOpen Wrench (1 pc.) Open Wrench (1 pc.) Open Wrench (1 pc.) Open Wrench (1 pc.) Open Wrench (2 pc.)Size=24mm Size=16mm Size=13mm Size=10mm Size=8mmHex Key (1 pc.) Hex Key(1 pc.)Size=8mm Size=6mmASSEMBLYCarrier Assembly1. Install front panel (2), back panel (3) and side rail (4) to carrier base (1) with M5x10 hex bolt (5) and M5 lock nut (6), insert ring (7) into the holes on carrier base, tighten with M6 washer (8) and M6 lock nut (9). See FIG 1.2. Install longer hinge (12) to the upper corner piece of carrier, and then install the UL hinge (14) to the lower corner of the carrier, align the holes, put the support sleeve (13) in the middle of longer hinge (12) and UL hinge (14), align the holes, insert M8x215 allen bolt (10) through pin assembly (11), longer hinge (12), support sleeve (13) and UL hinge (14) with M8 lock nut (15) and then tighten. See FIG 2.FIG: 1FIG: 23. Install support bracket (16) under the carrier base (1) with M8x45 allen bolt (17), M8 washer (18) and M8 lock nut (15), then tighten. See FIG 3.Remark: pin assembly (11) need to be inserted into the hole as below.FIG: 34. Install ramp (19) with UL hinge (14), tighten with M10x30 allen bolt (20), washer (21) and M10 lock nut (22). See FIG 4.FIG: 45. Install folding bar (25) and support backet (16), align the holes and tighten with M16 hex bolt (27) and M16 lock nut (28), Safety pin (26) is used for folded ramp and vertical position, See FIG 5.FIG: 5Diagram & Parts ListFor replacement parts and technical questions, please call 1-800-222-5381.WARRANTYOne-year limited warrantyDistributed byNorthern Tool + Equipment Co., Inc.Burnsville, Minnesota 55306Made in China。
CABLE SELECTION GUIDEHCS ® INDUSTRIAL GRADED-INDEX AND STEP-INDEX FIBER OPTIC CABLEOFS | 55 Darling Drive, Avon, CT 06001CABLE SELECTION GUIDEINDOOR AND OUTDOOR DESIGNSOptical Fiber Cables for Use in Substation Automation, Factory Automation, Industrial Ethernet, HVDC Systems, and Power ElectronicsHCS ® INDUSTRIAL GRADED-INDEX AND STEP-INDEX FIBER OPTIC CABLECABLE SELECTION GUIDEW W W.O F S O P T I C S.C O MWhy HCS and GiHCS ®?200 μm Step-Index Hard Clad Silica62.5 μm OM1 Graded-Index Hard Clad Silica • Wide operating temperature range• Resistant to abrasion, vibration, and industrial chemicals• HCS extends the distance and bandwidth of POF (Plastic Optical Fiber) Systems • Superior crush, twist, tensile strength, and flex performance• Ideal for Broadcom Versatile Link, Industrial Ethernet, Fieldbus, and Power over Fiber (PoF)• Suitable for indoor and outdoor use62.5 µmPictureC210582.2 mmLSZH Simplex22 mm5 lbs (22.2 N)ST, SMA, V-Pin, LC BC04265-10 2.2 mm PVC Simplex 22 mm5 lbs (22.2 N)ST, SMA, V-Pin, LC AC01281-10 2.5 mm PVC Simplex 25 mm55 lbs (244.7 N)ST, SMAC21050 2.5 mm LSZH Simplex 25 mm 55 lbs (244.7 N)ST, SMA HCS ® INDUSTRIAL GRADED-INDEX AND STEP-INDEX FIBER OPTIC CABLE CABLE SELECTION GUIDEW W W.O F S O P T I C S.C OMHCS ® INDUSTRIAL GRADED-INDEX AND STEP-INDEX FIBER OPTIC CABLECABLE SELECTION GUIDEThe cables in this brochure are intended to be used with OFS Crimp & Cleave field termination connectors andtermination kits.PictureC210608.0 mm (2.2 mm Subs) LSZH 2-Fiber Breakout 80 mm 45 lbs (200.2 N)ST, SMA, V-Pin, LC C210639.5 mm (2.2 mm Subs)LSZH 2-Fiber Glass Armor 95 mm 200 lbs (889.6 N)ST, SMA, V-Pin, LC C210528.0 mm (2.5 mm subs) LSZH 2-Fiber Breakout 80 mm 155 lbs (689.5 N)ST, SMAFor additional information please contact your sales representative.You can also visit our website at or call 1-888-fiberhelp (1-888-342-3743) USA or 1-770-798-5555 outside the USA.。
汉能薄膜发电集团地址：北京市朝阳区安立路0-A号 网址： 电话：400-688-1566负责声明：本文档信息仅供参考，不构成任何邀约或承诺，汉能可能不经通知修改上述信息，恕不另行通知。
每安装25W薄膜太阳能产品，所达成的减排效果，就相当于在地球上多种了一棵树汉能品牌尖端技术汉能先后并购德国Solibro、美国MiaSolé、Global Solar Energy 和Alta Devices公司，在全球设立八大研发中心，通过全球技术整合和持续自主创新，保持薄膜太阳能发电效率的五项世界纪录，其中砷化镓(GaAs)组件获得美国国家可再生能源实验(NREL)认证，最高转换效率达31.6%，薄膜太阳能转换效率世界第一。
尖端装备汉能始终坚定不移地推进并率先完成了薄膜太阳能装备的国产化、规模化，目前已经具备了超GW级装备交付能力，成为全球最大的薄膜太阳能产线“交钥匙提供商”。
通过与多个移动能源产业园合作，实现了薄膜太阳能产线解决方案的销售，并开始规模化交付。
多领域应用目前，汉能的薄膜太阳能产品已经广泛应用于建筑屋顶、建筑幕墙、道路、汽车、船舶、共享单车、无人机、卫星、便携式户外充电、电子设备、特种装备等领域。
针对城市降低能源消耗的需求，汉能针对性地推出生态城市综合解决方案，助力“生态城市、低碳城市、美丽城市”建设。
0102汉能汉瓦古法琉璃，今朝汉瓦汉瓦承载着东方古韵与中国浓厚的文化既媲美于中国的琉璃瓦，也彰显着现代建筑的智慧汉瓦将现代科技融入传统建筑，用薄膜太阳能赋予屋顶新的生命汉瓦颠覆了建筑对外部能源的依赖，让零能耗建筑成为可能0304汉瓦将轻薄、高效、柔性的铜铟镓硒(CIGS)薄膜太阳能芯片通过内外双层的夹胶封装工艺，精密封装在透光度超过91.5%的玻璃内层中，最大限度地保持薄膜太阳能的高转换率特性。
高效转化率，助力新能源汉瓦，改变世界的屋顶汉瓦传承东方建筑之美，融合中国传统屋面瓦—琉璃瓦的美学基因，用尖端技术和精巧工艺，完美表现了瓦片晶莹剔透之美及拱形曲面的柔美。
HM5006抗干扰介质损耗测试仪说明书武汉国电华美电气有限公司电话：84663808邮箱：官网： 地址：武汉市汉南区华顶工业园A25-1统一热线：4000-935-230前言 (2)一、仪器概述 (3)二、安全措施 (3)三、可测试参数 (4)四、性能特点 (4)五、技术指标 (5)六、测量方式及原理 (6)七、常见设备的接线方法 (7)八、仪器功能简介 (10)九、仪器操作步骤 (11)十、现场试验注意事项 (14)十一、仪器检定 (15)十二、变频测量讨论 (16)十三、仪器的装箱清单 (17)前言一、衷心感谢您使用本公司的产品，您因此将获得本公司全面的技术支持和服务保障。
二、本使用说明书适用于抗干扰介质损耗测试仪。
三、当您在使用本产品前，请仔细阅读本使用说明书，并妥善保存以备查考。
四、请严格按说明书要求步骤操作，使用不当可能危及人身安全。
五、在阅读本说明书或仪器使用过程中如有疑惑，可向我公司咨询。
使用本仪器前，请仔细阅读操作手册，保证安全是用户的责任本手册如有改动，恕不另行通知。
介损测量是绝缘试验中很基本的方法，可以有效地发现电器设备绝缘的整体受潮劣化变质，以及局部缺陷等。
在电工制造、电气设备安装、交接和预防性试验中都广泛应用。
变压器、互感器、电抗器、电容器以及套管、避雷器等介损的测量是衡量其绝缘性能的最基本方法。
HM5006抗干扰介质损耗测试仪突破了传统的电桥测量方式，采用变频电源技术，利用单片机、和现代化电子技术进行自动频率变换、模/数转换和数据运算；达到抗干扰能力强、测试速度快、精度高、全自动数字化、操作简便；电源采用大功率开关电源，输出45Hz和55Hz 纯正弦波，自动加压，可提供最高10千伏的电压；自动滤除50Hz干扰，适用于变电站等电磁干扰大的现场测试。
广泛适用于电力行业中变压器、互感器、套管、电容器、避雷器等设备的介损测量。
二、安全措施1、使用本仪器前一定要认真阅读本手册。
2、仪器的操作者应具备一般电气设备或仪器的使用常识。
