下载文档原格式
ABOUT THIS WRECKER TOWING MANUALFord Motor Company salutes and applauds the towing industry for many fine years of service to the automotive industry. We will continue to work to provide our customers with guidelines.This manual contains the latest towing procedures for 2010 Ford, Lincoln and Mercury vehicles. Ford Motor Company has created easy-to-follow instructions with illustrations showing the correct hook-up for damage-free towing.As an additional safety measure, be sure to use safety chains on every tow, including wheel lift and flatbed hook-ups. This procedure will prevent losing the vehicle in the event of equipment failure or vehicle breakage at the chain attachment.New materials and aerodynamic styling require new methods of towing to eliminate the possibility of damage to vehicles when towing. Wheel lifts or flatbed equipment is required to tow Ford Motor Company vehicles. Refer to the instructions given for the specific vehicle to be towed.GENERAL TOWING INFORMATIONNOTE, NOTICE AND WARNINGAs you read through this manual, you may come across a NOTE, NOTICE or WARNING. Each one is there for a specific purpose. A NOTE calls attention to unique, additional or essential information related to the subject procedure. A NOTICE identifies a hazard that could damage the vehicle or property. A WARNING identifies a hazard that could result in severe personal injury or death to yourself or others.Preparatory StepsWARNING: NEVER USE A TOW BAR THAT ATTACHES TO THE FASCIA/BUMPER WHEN TOWING THE VEHICLE. THE FASCIA/BUMPER COULD BE DAMAGED AND CAUSE AN ACCIDENT. NOTICE: Incorrect towing of the vehicle may result in damage to the transmission/transaxle, transfer case, front or rear fascia, steering/suspension or exhaust. Always follow the outlined towing procedures. It is recommended that only an unloaded vehicle be towed. NOTICE: Always consult the tow equipment manufacture for specific instructions on how to operate their equipment.It is the tow equipment operator’s responsibility to evaluate and adjust to the specific towing conditions to prevent damage to the vehicle.If a vehicle has been modified, consult the equipment modifier/supplier for the specific towing equipment.NOTE: When towing the vehicle, the steering wheel should be left unlocked.NOTE: Disabling the air bag system is not necessary in most cases. An air bag is highly unlikely to deploy during towing. Standard towing or recovery procedures on an air bag equipped vehicle should not cause air bag deployment. Only a significant frontal impact that closes 2 crash sensors will deploy an air bag.NOTE: Turning the ignition switch to OFF will not disable the Ford air bag system. The air bag deployment system operates independently of the ignition position.If the air bags are not deployed, and as a precaution the air bag system would need to be disabled, disconnect the battery in a safe manner.Release the parking brake and place thetransmission/transaxle in NEUTRAL. As a general rule, vehicles should be towed with the drive wheels off the ground. If the vehicle is to be towed on its drive wheels, place the drive wheels on a dolly.When a vehicle is towed on its front wheels, the steering wheel must be clamped in the straight-ahead position with a steering wheel clamping device designed for towing service use, such as those provided by towing system manufacturers.Do not use the vehicle steering column lock to lock the wheels in a straight-ahead position when towed from the front or rear. If equipped with an ignition key and the ignition key is not available, place a dolly underneath the driving wheels of the vehicle and tow with the non-drive wheels raised.Brake-Shift InterlockAll Ford, Lincoln and Mercury vehicles incorporate a brake-shift interlock feature that prevents the gearshift lever from beingmoved from PARK when the ignition is in the ON position, unless the brake pedal is depressed. If you cannot move the gearshift lever out of PARK with the ignition in the ON position and the brake pedal depressed, refer to the automatic transmission or transaxle section in the driving section of the applicable Owner’s Literature.Flat BedsNOTICE: On vehicles equipped with an air suspension system, be sure the air suspension service switch is turned off prior to vehicle tie down. NOTICE: Never fasten J-hooksto any suspension or drivelinecomponents.When using a flatbed to transport a vehicle, unless indicated otherwise, use T-hooks inserted in the appropriate tie-down slot. Never fasten J-hooks to any suspension wheel or driveline component because J-hooks will damage these components. When using winches, care must be taken to avoid damaging the fascia/bumper system, lower body panels or air dams. Wheel LiftNOTICE: Check vehicle specifications for raised vehicle height requirements. If these height requirements are not followed, damage to the body and/or the underbody may result.NOTICE: When towing over very rough or crowned intersection roads, the following special procedures are required when using any wheel lift equipment. The vehicle must be secured to the wheel lift equipment using safety chains equipped with T-hooks or safety hooks. If these procedures are not followed, damage to the underbody may result from excessive jounce travel of the suspension.1. Attach the safety chain T-hooks in the appropriate slot of the body or frame of the vehicle to be towed unless otherwise specified.2. Run the chain through the hooks on the wheel lift crossbar and attach it to the towing vehicle.3. Make sure that there is no slack in the safety chain between the vehicle and the crossbar.4. Repeat Steps 1 and 2 for the other side of the vehicle.SlingbeltsFord Motor Company does notrecommend the use of slingbelttowing. Using slingbelt towingprocedures may cause damageto the fascia, lower body panels,air dams or other components.Towing Speeds and DistanceNOTE: If a distance of 50 mi (80 km) and/or a speed of 35 mph (55 km/h) is exceeded, or when the vehicle istowed with the drive wheels on the ground, position dollies under the wheels. Towing speed should not exceed 50 mph (80 km/h) when the vehicle is towed with the front wheels off the ground. Do not tow with both front and rear wheels on the ground. NOTE: On rough pavement, the maximum towing speed is 35 mph (55 km/h). Maximum towing speed of 35 mph (55 km/h) should be used whenever the tow truck operator is not sure of road surface condition.See specific model instructions for vehicle towing speed and distance limitations.UNLTD = Unlimited miles, at speeds up to 50 mph (80 km/h).Refer to the dolly manufacturer for speed and weight limitations.Towing Four-Wheel Drive Vehicles with Lever-Operated Transfer Case – F-150, F-250 through F-5501. Place the automatic transmission in PARK ormanual transmission in 1st gear.2. NOTE: The transfer case NEUTRAL setting islocated between 4H and 4L. In order to place thetransfer case in NEUTRAL, the lever must be moved slightly to the left and rearward of the 4H position.With the ignition in the ON position, both the 4x4 and LOW RANGE indicators will be OFF when thetransfer case is in NEUTRAL. If the battery is dead, jump the vehicle to make sure the indicator lights are off.Place the transfer case in N (NEUTRAL).3. NOTE: To verify that the hubs are in the FREEposition, the front driveshaft should turn freely.On an F-Super Duty, set and verify that the manual locking hubs are in the FREE position. Use dollies if the hubs do not unlock.Towing speed should not exceed 50 mph (80 km/h).This applies with either the front or rear wheels offthe ground.Towing Four-Wheel Drive Vehicles with Electronic Shift Transfer Case – F-150, F-250 through F-550, Ranger and Sport-Trac1. NOTE: With the ignition in the ON position, both the4x4 HI and the LOW RANGE indicators will be OFF when the transfer case is in 2 HI. If the battery isdead, jump the vehicle to make sure the indicatorlights are off.2. Place the automatic transmission in PARK ormanual transmission in 1st gear.3. NOTE: Manual locking hubs apply to F-250 throughF-550 only.Set the locking hubs to the AUTO position. Verifythat the hubs are unlocked. Use dollies if the hubsdo not unlock. Once these conditions are met, follow the instructions for towing a 2-wheel drive vehicle.WARNINGS, NOTICES AND NOTES( See page 4 for specific vehicle application)A NOTICE: Ford Motor Company has not approved aslingbelt towing procedure. It is recommended thatthe vehicle be towed with a flatbed or wheel liftequipment. If the vehicle is towed by any othermeans or incorrectly, damage to the vehicle mayoccur.B NOTICE: If the vehicle is to be towed from the frontor rear using wheel lift equipment, the lifted tiremust be raised to a clearance height ABOVE thedollied tire to prevent damage to the vehicleundercarriage.The clearance height is the difference between thebottom of the wheel lifted tire and the bottom of thevehicle’s dollied tire. (See Illustration numbers 3and/or 5.)C NOTICE: It is recommended that the vehicle (4WD,AWD, FWD and some RWD) be towed from the rearusing wheel lift equipment. It is required that thefront wheels be placed on a dolly to prevent damage to the vehicle fascia/bumper and/or the FWD, 4WDand AWD system.D NOTICE: It is recommended that the vehicle (4x2,4WD, AWD, RWD and some FWD) be towed from the front using wheel lift equipment. It is required thatthe rear wheels be placed on a dolly to preventdamage to the vehicle fascia/bumper and/or thedriveline system.E NOTICE: On a vehicle equipped with fog lamps or asport package, care must be taken not to damagethe components while loading and towing with awheel lift or flatbed. For flatbed towing, wraploading cable with a shop towel to protectfascia/bumper from damage.F WARNING: ON VEHICLES EQUIPPED WITH THEFIRE SUPPRESSION SYSTEM, COMPLETE ALLPRE-TOWING, UNDER-VEHICLE ACTIVITY(SECURING VEHICLE, CHAINS, STRAPS, ETC.)BEFORE TURNING THE KEY TO THE RUNPOSITION. THE FIRE SUPPRESSION SYSTEM ISACTIVE WHENEVER THE KEY IS IN THE RUNPOSITION AND WILL DEPLOY IF THE MANUALACTIVATION BUTTON IS DEPRESSED.G NOTICE: On a vehicle equipped with an airsuspension system, the system switch must beturned to the off position before the vehicle can betowed. Refer to the Owner’s Literature for procedure and switch location. If the rear air bags are deflated, load the vehicle on a flatbed and use a 4x4 boardunder the bed to lift the rear of the vehicle so thatthe rear bumper will not drag on the road surface.H NOTICE: When a vehicle is towed over very rough,pitching roads such as a crowned road intersection at a railroad crossing, towing speed should begreatly reduced to avoid damaging the vehicleundercarriage.I WARNING: DO NOT TOW VEHICLE BACKWARDWHEN TOWING THE VEHICLE WITH ALL 4 WHEELS ON THE GROUND.J NOTICE: Crossbeam/spacer blocks must be used to keep the cable from coming in contact with the chin spoiler when loading on a flatbed. Thecrossbeam/spacer block can be held in place on the frame using bungee cords.K NOTICE: Do not disconnect the driveshaft since the system is aligned and balanced. Connecting thedriveshaft in the wrong position may cause vibration or damage to the driveline.L NOTICE: Manual transmission vehicles MUST have the parking brake fully engaged when the rearwheels are on the dolly. Failure to apply the parking brake may cause damage to the driveline.M NOTICE: It is recommended that the vehicle be loaded onto a flatbed tow truck with the tow hookattached to a canvas strap, to prevent damage to the bottom of the front or rear fascia/bumper covers. Ifthe cable, chain or strap comes in contact with thefascia, wrap the tow cable, chain or strap with ashop towel.N NOTICE: It is recommended when using a flatbed, use mini J-hooks to tie down the front of the vehicle.Larger J-hooks may cause damage to theundercarriage.O NOTE: For Dual Rear Wheel (DRW) vehicles, it may be necessary to remove the outer rear wheel whenusing wheel lift equipment.P NOTE: On a 4WD vehicle with Electronic Shift on the Fly (ESOF), it is recommended that the vehicle betowed with a wheel lift and dolly or flatbedequipment with all the wheels off the ground.Q NOTE: On a 4WD vehicle with Manual Shift on Stop (MSOS) with the lever operated transfer case inNEUTRAL, it is acceptable to tow the vehicle withthe rear wheels on the ground.R NOTE:For towing or operating conditions other than what is prescribed in this manual, thedriveshaft must be removed to prevent drivelinedamage. Always mark the location of the driveshaftto the attaching flange before removal so the shaftcan be correctly indexed upon installation.Driveshaft attachment bolts should be replaced with new OEM bolts or have threadlocking compoundadded to the original bolts.Reinstall the driveshaft per the workshop manual.TOWING SPECIFICATION AND ILLUSTRATION TABLEFlatbedFront and Rear Wheel LiftVehicleW a r n i n g s , N o t i c ea n d N o t e sF l a t B e dT i e D o w nW h e e l L i f t —F r o n tW h e e l L i f t —R e a rC l e a r a n c eH e i g h t —F r o n tC l e a r a n c eH e i g h t —R e a rT o w i n g f r o mF r o n tm p h – k m /hm i l e s - k mT o w i n g f r o mR e a rm p h – k m /hm i l e s - k mCARSCrown Victoria, Grand Marquis, Town Car (RWD) A,B,F,G,I1,6,7 14 3 4 12 in 12 in W/Dolly * Unltd W/O Unltd Focus (FWD) A,B,C,H,I 1 12 2 5 12 in 12 in W/O Unltd W/Dolly Unltd Fusion/Fusion Hybrid,Milan/Milan Hybrid, MKZ (AWD) A,B,C,D,E,I 1 22 3 5 19 in 19 in W/Dolly Unltd W/Dolly Unltd Fusion/Fusion Hybrid,Milan/Milan Hybrid, MKZ (FWD) A,B,C,E,I 1222519 in19 inW/OUnltdW/DollyUnltdFusion Sport (FWD) A,B,C,E,I,M 1,6,8 22 2 5 19 in 19 in W/O Unltd W/Dolly Unltd Taurus/MKS (AWD) A,B,C,D,E,I,M 1 23 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Taurus/MKS (FWD) A,B,C,E,I,M 1 23 2 5 12 in 12 in W/O Unltd W/Dolly Unltd Mustang (RWD) V6 A,B,C,D,I,K,L 1 13 3 5 18 in 14 in W/Dolly Unltd W/Dolly Unltd Mustang (RWD) V8A,B,C,D,I,K,L 1 13 3 5 16 in 14 in W/Dolly Unltd W/Dolly Unltd Mustang Shelby GT 500 (RWD)A,B,C,D,I,K,L,M,N 1,7,8,9 133N/A16 in14 inW/DollyUnltdN/AN/ATRUCKS E-Series, E-150/250/350/450 A,B,E,I,O,R 1 14 3 4 12 in 12 in W/Dolly Unltd W/O Unltd Edge/MKX (AWD) A,B,C,D,E,I 1 20 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Edge/MKX (FWD) A,B,C,D,E,I 1 20 2 5 12 in 12 in W/O Unltd W/Dolly Unltd Escape/Escape Hybrid, Mariner/Mariner Hybrid (4WD) A,B,C,D,I 1 15 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Escape/Escape Hybrid, Mariner/Mariner Hybrid (FWD) A,B,C,D,I 1 15 2 5 12 in 12 in W/O Unltd W/Dolly Unltd Expedition/ Navigator (4WD) A,B,C,D,G,I,Q,R 1 18 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Expedition/ Navigator (RWD) A,B,D,G,I,R 1 18 3 4 12 in 12 in W/Dolly * Unltd W/O Unltd Explorer/Mountaineer/Sport Trac (4WD)A,B,C,D,I,R 1 19 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Explorer/Mountaineer/Sport Trac (RWD)A,B,C,D,I,R 1 19 3 4 12 in 12 in W/Dolly * Unltd W/O Unltd F-150 (4WD) A,B,C,D,G,I,Q,R 1 18 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd F-150 (RWD)A,B,D,G,I,R 1 18 3 4 12 in 12 in W/Dolly * Unltd W/O Unltd F-250/350/450/550 (4WD) A,B,I,J,O,P,Q,R 1,10 16 3 5 12 in 12 in W/Dolly Unltd ** W/O Unltd F-250/350/450/550 (RWD) A,B,J,I,O,R 1,10 16 3 4 12 in 12 in W/Dolly * Unltd ** W/O Unltd Flex/MKT (AWD) A,B,C,D,E,I,M 1 21 3 5 15 in 14 in W/Dolly Unltd W/Dolly Unltd Flex/MKT (FWD) A,B,C,E,I,M 1 21 2 5 15 in 14 in W/O Unltd W/Dolly Unltd Ranger (4WD) A,B,C,D,I,R 1 17 3 5 12 in 12 in W/Dolly Unltd W/Dolly Unltd Ranger (RWD) A,B,D,I,R 1 17 3 4 12 in 12 in W/Dolly * Unltd W/O Unltd Transit Connect A,B,C,H,I1112512 in12 inW/OUnltdW/DollyUnltd* In case of an emergency, the vehicle can be towed with the drive wheels on the ground up to a speed of 35 mph (55 km/h) and up to a distance of 50 mi (80 km).** On a 4X2/4X4 vehicle in 2HI and the hubs in the AUTO/FREE position, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground.ILLUSTRATIONS。
Vito Ambulance威霆高级监护转运型医疗车梅赛德斯—奔驰威霆122高级监护转运型医疗车集优越设计、强劲动力和出众的操控性于一身，车辆搭载3.0升V6汽油发动机，5速自动变速箱，凭借其蕴含尖端科技的主动、被动安全配置，全面保证出行安全和工作效率。
结合最高安全标准与先进救护设备的威霆122高级监护转运型医疗车，优化的空间利于车内抢救操作，灵活的操控性能更适应城市内的狭窄道路行驶。
可提供病患快速转运、增加黄金救援时间，达到极佳医疗救护质量与护理服务等完整的医疗服务。
梅赛德斯-奔驰Vito 122高级监护转运型医疗车颜色：白色/红色产地：中国/北京型号：梅赛德斯-奔驰Vito 122医疗舱专业改装产品图片示意图（图片仅供参考，与客户实际定制为准）奔驰Vito122救护车左前右侧视图奔驰Vito122救护车左前左侧视奔驰Vito122救护车正视图奔驰Vito122救护车后视图奔驰Vito122救护车驾驶室视图奔驰Vito122救护车驾驶室视图奔驰Vito122救护车医疗舱全景视图奔驰Vito122救护车医疗舱全景视图奔驰Vito122救护车医疗舱局部视图奔驰Vito122救护车医疗舱局部视图车辆主要技术参数与配置尺寸和质量轴距mm：3430车体尺寸mm: 5223 x 1901 x 2360(长 x 宽 x 高) 医疗舱尺寸mm: 2900 x 1650 x 1750(长 x 宽 x 高) 整车整备质量kg: 2460满载总质量kg: 3100发动机燃油种类: 汽油工作方式: 水冷/V型6缸/4冲程/多点电喷谐波共振进气系统和发动机二次空气喷射系统。
排气量cm3: 2996压缩比: 11:1排放标准: GB18352.3-2005（国Ⅳ阶段）最大功率kw/rpm: 165/5800最大扭矩Nm/rpm: 290/4500制动系统4轮盘式制动变速器:自动变速器5档自动变速器最高时速km/h:190车辆标准配置防抱死制动系统 (ABS)电子防侧滑系统（ASR）电子稳定系统（ESP）辅助制动力系统(BAS)制动力分配系统(EBD)防侧翻系统(ROM)干涉侧滑系统(RMI)负载适用控制(LAC)扩展转向不足控制(EUC)驾驶室两座椅驾驶员和副驾驶双安全气囊电动窗, 中控门锁带遥控功能、电动窗边后视镜、前后雾灯上掀式后门，液压支杆医疗舱车厢右侧为可开启玻璃窗空调及照明系统驾驶室安装空调医疗舱安装原厂空调并加装原厂暖风机（双暖风）医疗舱车顶安装双向排风系统车顶尾部安装救护车外场用照明灯医疗舱内安装有4盏照明灯担架床顶部装有两盏手术射灯医疗舱照明系统可有效满足医务人员在舱内救治病人的需要紫外光消毒灯电源系统蓄电池安装在副驾驶座位底下及其所有连接防止任何情况下发生短路的可能10m长移动电缆医疗舱内安装2个220v插座医疗舱安装2个12v插座220V/16A防水、带防护盖的外接电源插座紧急警报系统驾驶室安装警报、警灯控制按扭车辆安装双电喇叭、警笛、麦克、警报声响为慢速双音转换调，符合公安部有关规定车外扩音器内置于警报器车顶前部安装长条闪光警灯（蓝色）车顶尾部左右两侧装有蓝色警示灯2个、尾部安装两个指示灯医疗舱内装置驾驶室与医疗舱安装分隔墙, 分开前后车厢, 分隔墙上有二个滑行窗,窗户透明医疗舱分隔墙后右侧安装一张有安全带的座椅医疗舱内右侧安装带有安全带的四人座长条椅及储物柜医疗舱左侧顶部安装3个6门透明滑行门储物柜医疗舱左侧安装呼吸机、湿化瓶专用的氧气插座医疗舱中隔墙后安装一个医药储物柜医疗舱内设有完备密闭式的供氧系统医疗舱中隔墙后左侧设置可以置放2个10L氧气瓶的柜子医疗舱顶部担架上方安装滑轨式输液固定装置，输液固定装置每个挂钩可承受10kg重量，能够容纳2袋液体。
前机舱一览前机舱一览序号说明1冷却液膨胀箱2电机控制器3高压控制盒4充电机+DCDC总成5制动液储液罐6前舱保险丝盒7蓄电池8散热器加注口9电池冷却水壶10洗涤液储液罐安全性操 纵驾驶指南使用指南自己动手技术数据索 引减速器润滑油至少每隔50,000 km更换一次，如果驾驶工况比较恶劣，建议提前更换减速器润滑油。
由众泰汽车特约服务店更换减速器润滑油。
减速器润滑油更换安全性操 纵驾驶指南使用指南自己动手技术数据索 引却液液位在“FULL”线和“LOW”线之间。
如果液位低于“LOW”线，须加注冷却液。
膨胀箱中的冷却液液位随动力系统温度的变化而变化。
但是，如果液位在“LOW”线以下，则应添加冷却液，使液位位于“FULL”线和“LOW”线之间。
却水壶侧面标记范围内。
冷却液液位应位于上限标记“MAX”与下限标记“MIN”之间。
1. 打开前机舱盖，拆卸前机舱饰盖。
2. 为防止烫伤，使用湿毛巾盖住加注口盖，慢慢按逆时针方向拧开加注口盖，并将其取下。
3. 将适量的冷却液注入散热器加注口中，加满加注口4. 重新装上散热器加注口盖，将其拧紧。
安全性操 纵驾驶指南使用指南自己动手技术数据索 引察看制动液储液罐上的液位。
此液位必须总是保持在标记“MIN（最低）”和“MAX（最高）”之间。
在车辆运行中，由于制动摩擦片的磨损及其自动调节，制动液液位会略有降低，此为正常情况。
Time 23;12 OUT -34.5℃ODO 0 km T ripA 0.0km剩余电量100% 工作电流： 999.9A 工作电压：999.9V0011111122222224444356678889×1000rpmkm/h60RP N60制动液位低但是，如果液位在较短的时间内即明显降低，或降到标记“MIN（最低）”之下，则可能是制动系统泄漏。
如果制动液液位过低，则制动器指示灯也会亮起。
在这种情况下，请联系特约服务站进行检修。
制动液因制动系统是关系到安全的重要系统，所以请您经常检查制动器各相关部件，保证它们在正常的工作范围。
12378910目录欢迎您加入日益兴旺的新型INFINITI英菲尼迪车主的行列。
我们满怀信心地向您提供该新型INFINITI英菲尼迪汽车。
它是用最新技术并在严格的质量管理下制造的。
本使用说明手册是为您了解车辆的操作和保养而准备的，有了它，您可享受久驶不损之乐趣。
在使用本车之前，请通读本手册。
另附的《保修和保养手册》对车辆的保修进行了详细的说明。
INFINITI英菲尼迪经销店最了解您汽车的情况。
如果您需要什么服务或有任何问题，我们都会运用重要的安全信息安全注意事项！遵守下列重要的驾驶规则，可确保您和乘客旅途的安全！.切勿酒后或服药后驾驶。
.务必观察限速标志，切勿超速驾驶。
.务必使用安全带及恰当的儿童保护装置。
未满13岁的儿童应坐在后座。
.务必提醒乘客车辆安全装置的正确使用方法。
.务必查阅本使用说明手册以获取重要的安全信息。
本手册说明本手册包括了有关该车型所有选装件的资料。
因此您可能会发现其中有些资料并不适用于您的车辆。
本手册中的所有资料，包括规格和插图，在本手册出版时有效。
INFINITI英菲尼迪汽车公司保留在任何时候修改车辆的规格或设计的权利，恕不另行通知。
车辆的改装不应对该车辆进行改装。
改装可能会影响车辆的性能、安全性或耐久性，甚至可能会违反政府的法规。
另外，INFINITI英菲尼迪汽车公司提供的保修服务将不包括由于改装所引起的损坏或性能问题。
请先阅读—然后安全驾驶在驾驶车辆之前，请仔细阅读本用户手册。
这能确保您熟悉车辆的控制与保养要求，有助于您安全驾驶。
在本手册中，我们使用了符号伴随警告二字。
这表示有可能导致死亡或严重人身伤害的危险。
要避免或降低这种风险，必须认真遵守操作程序。
在本手册里还使用符号伴随注意二字来表示有可能引起轻微或中度人身伤害或车辆损害的危险。
要避免或降低这种风险，必须认真遵守操作程序。
SIC0697如果您看到此符号，它表示“请勿进行此操作”或“请勿让此情况发生”。
如果您在插图中看到与此类似的符号，它表示箭头指向车头。
按品牌分包括全顺、奔驰、大通、金杯、丰田、大众、特顺、福田、东风等
（1）全顺救护车包括：v348、v362（转运型/监护型）
全顺v348短轴中顶汽油/柴油、v362中轴中顶汽油/柴油、v348长轴高顶柴油
（2）奔驰救护车包括：奔驰凌特315、凌特324、威霆122（转运型/监护型）
都是汽油型救护车
（3）大通救护车包括：v80、G10（转运型/监护型）
大通v80短轴中顶柴油型救护车、大通v80长轴中顶柴油型救护车、大通v80长轴高顶柴油型救护车、
（4）金杯救护车包括：高顶、海狮高顶、海狮平顶（转运型/监护型）（5）丰田包括：丰田海狮救护车（转运型/监护型）
（6）大众包括：大众t6、大众t5（转运型/监护型）
大众T6高顶/平顶汽油型救护车、大众T5高顶救护车
（7）特顺包括：长轴高顶柴油型救护车（转运型/监护型）
（8）福田救护车包括：福安G7汽油型救护车（转运型/监护型）（9）东风救护车包括：东风M5汽油型救护车（转运型/监护型）
四川爱普康新能源公司
2018-7-2。
A 参见“锁定和解锁”(页码27)。
参见“免钥匙进入”(页码28)。
B 参见“检查雨刷片”(页码39)。
C 参见“保养”(页码136)。
D 参见“拖曳点”(页码134)。
E 参见“更换灯泡”(页码47)。
F 胎压参见“技术规格”(页码162)。
G 参见“更换车轮”(页码155)。
E133220BCDE F GE133222A 参见“电动车窗”(页码57)。
参见“车外后视镜”(页码58)。
E140773A出风口。
参见“出风口”(页码86)。
B转向指示灯开关。
参见“转向指示灯”(页码43)。
远光。
参见“远光和近 光”(页码41)。
C信息显示控制。
参见“信息显示”(页码72)。
E133221A参见“更换雨刷片”(页码39)。
B参见“更换灯泡”(页码47)。
C参见“更换灯泡”(页码47)。
D参见“油箱门”(页码106)。
E参见“更换车轮”(页码155)。
警告身高低于150cm或者小于E68918体重小于13kg的婴儿必须安放在婴儿安全座椅（0+类）上，婴儿安全座椅E70710建议您使用包含座垫和靠背的增高座椅。
升高的座椅位置，可以将成人座椅安全带的肩带跨过儿童肩部的中间E132903上拉带固定点位于置物板上的可翻转盖板下面。
配备有上拉带的儿童安全座椅的E13290218用力推儿童安全座椅椅背并使左侧逆时针转动开锁，顺时针转动上锁。
E78298E74302驾驶员安全气囊、前排乘客安全气囊和前排座椅安全带预紧器将在严重的正面碰撞或偏左右30°范围内碰撞时E75004侧安全气帘安装于前排车窗和后排车窗上部的饰板内。
B柱饰板上的标签E72658侧安全气囊安装于前排座椅的靠背内部。
靠背上的标签表示您的车辆配备E85817将安全带缓慢地拉出。
若猛烈的拉出或车辆处于斜坡位置时，安全带会锁注意:按下锁止按钮时，稍微提起滑杆，更容易打开锁止机构。
按下调节器上的锁止按钮，根据需要上下调节安全带高度。
安全带提示器警告安全约束系统只在正确使用安最低限速，安全带提示灯将点亮，并E87511(G1353417)E68587下的旧电池放至当地指定的电池回收配备可折叠钥匙齿片的遥控器E1288091.在图示位置插入一字螺丝刀，并轻轻地推动卡扣。
