警铃组使用说明书

警铃管理制度
警铃管理制度
1、警铃的使用原则上由矿调度室发出使用指令后，由指定人员发出警报，并启动相关警铃装置。

2、任何单位或个人，不得以任何理由拆除或迁移警铃装置，严禁随意启动或挪作它用。

3、任何单位和个人都有权利和义务维护整个报警系统。

对破坏和滥用警铃装置的行为，有权制止和处罚，并报告矿调度室。

4、由矿调度室负责，每月定期进行一次警报实验，实验结果要存档案备查，对查出的问题要及时通知有关单位进行处理。

5、警铃的安装位置要求在支护完好、巷道畅通、无积尘、无淋水、无杂物的地点，且该地点附近有固定岗位人员工作，并指定人员管理。

6、警铃的设置由机电科负责设计，并随着开采的延伸和回撤，予以及时调整。

7、当某一地点发生透水、火灾或其它严重灾害情况紧急时，现场人员直接启动警报，通知受灾害地点人员撤离，并及时汇报矿调度室和安全科。

8、警报响起后，任何单位和个人都有权立即组织按避灾路线撤离，对行动迟缓或阻碍撤离的人员，要严肃处理直至追究法律责任。

9、对警铃使用管理过程中，有突出表现的单位或个人，将根据情况予以表扬和嘉奖。

一、概述：品牌大眼睛型号HP-99GSM类型防盗报警电话工作电压12（V）无线接收频率315（MHz）报警喇叭声强120（dB）录音留言时长6（S）储存电话号二、详细说明：品牌大眼睛型号HP-99GSM 类型防盗报警电话工作电压12（V）无线接收频率 315（MHz）报警喇叭声强 120（dB）录音留言时长 6（S）储存电话号码 6（个）电话号码位长 11（位）报警项目多功能密码设置功能有系统安装系统简介 本报警器由报警主机和各种无线连接的配件组成。

当有人非法进入设防区域时，主机就会发出警报声，并且拨打主人的电话，主人收到通知后可立即赶回家或通知附近的亲朋好友处理，也可以通过电话监听现场的声音，进行远程操作。

报警器安装把电话线外线插头插入主机的LINE2孔，用报警器附带的电话线将主机的LINE1孔与电话机相连，然后接上电源和警号，此时主机会发出“B”的一声，电源指示灯常亮，表示主机已开始工作。

门磁安装将随机配备的双面胶把磁条贴在门上，门磁发射盒贴在门框上，安装时注意将磁条靠近发射盒上有指示灯一侧，两者对齐，间距越小越好。

红外探测器的安装红外探测器的原理是感应人体发出的红外线信号，它能感应到人体的移动，探测距离通常为5-12米，红外探头应装在离地2.2米左右的位置，对准要探测的区域。

红外只能安装在室内，不要对着太阳光，不要对着窗户及温度容易改变的地方。

红外安装的位置会影响到探测距离及探测的准确性。

GSM卡安装抽出主机背后的SIM卡盖，用手指压住SIM卡座向后推动，翻开卡座盖板，将SIM卡按豁口位置插入盖板，保持SIM卡缺角与板上缺角方向一致，压下盖板向前推动扣住SIM卡即可。

功能设置所有设置都需要在撤防下进行，所有正确的操作均是长响一声，错误的操作都是两声短响调节报警时警笛音量# 0（0～99） #报警时调节警笛音量大小，0到99之间选择，0是无声，99是最大声。

设置普通报警电话号码 # (1～5) ?...? #设置1～5组电话号码，“1～5”为电话号码的序号；此处“?...?”代表电话号码。

兆科药业（广州）有限公司厂房及厂房A消防系统操作说明书广东华冠消防工程有限公司二O一四年三月(仅供参考使用)目录A．自动喷淋系统 (3)1、自动喷淋系统简介 (3)2、分布情况 (3)3、系统操作说明 (4)4、自动喷淋系统之一般重组系统操作 (5)5、湿式报警阀组之操作说明 (6)6、自动喷淋水泵启动控制屏 (7)7、自动喷淋系统之保养程序 (11)8、自动喷淋系统动作方框图 (12)8、自动喷淋系统系统图 (13)B．室内消火栓系统 (14)1．室内消火栓简介 (14)2．分布情况 (14)3．系统操作说明 (15)4．室内消火栓系统之重组系统操作 (16)5．消火栓水泵起动控制屏 (16)6．室内消火栓系统之保养程序 (19)7．室内消火栓系统动作方框图 (20)8．室内消火栓系统系统图 (21)C．室外消火栓系统 (22)1．室外消火栓系统简介 (22)2．分布情况 (22)3．系统操作说明 (22)4．室外消火栓系统之重组系统操作 (22)5．室外消火栓系统之保养程序 (23)D．火灾自动报警及联动控制系统 (24)1. 火灾自动报警及联动控制系统简介 (24)2.系统分布情况 (24)3.系统操作说明 (25)4.自动报警系统之重组系统操作说明 (26)5.自动报警系统之保养程序 (27)6.自动报警/联动系统流程示意图 (28)7.自动报警/联动系统图 (29)E．消防火灾紧急事故广播系统 (30)1．消防火灾事故广播系统简介 (30)2．分布情况 (30)3．系统操作说明 (30)4、消防火灾紧急事故广播系统动作方框图 (31)F．消防排烟系统 (32)1. 消防排烟系统消防简介 (32)2. 分布情况 (32)3. 系统操作说明 (32)4、风机启动控制屏 (33)5、防排烟系统之保养程序 (36)6、消防排烟系统流程示意图 (37)7、消防排烟系统图 (38)G．防火卷帘设备 (39)1. 防火卷帘设备简介 (39)2. 分布情况 (39)3. 系统操作说明 (39)4. 防火卷帘设备之保养程序 (41)5. 防火卷帘设备控制流程示意图 (42)H.S型热熔胶气体灭火系统 (42)1. S热气溶胶灭火系统简介 (43)2.系统分布情况 (43)3.系统操作说明 (43)4.气体灭火系统图 (44)I．灭火器设备 (46)1. 灭火器设备简介 (46)2. 手提式干粉灭火器操作说明 (46)A．自动喷淋系统1、自动喷淋系统简介**68度普通上喷头：6168个**68度普通下喷头：62个**直径150毫米湿式报警阀：9套**水流指示器：直径150毫米: 19套**水流指示器：直径100毫米: 1套**水流指示器：直径80毫米: 1套**喷淋水泵接合器：2套**喷淋泵：2台**喷淋稳压泵组：1组2、分布情况2.1本设计为兆科药业（广州）有限公司厂房及厂房A提供一个全覆盖之自动喷淋系统，保护点为厂房及厂房A。

©2004 Whelen Engineering Company Inc.Form No.13883A (073107)A u t o m o t i v e : S i r e n s /S w i t c h e sFor warranty information regarding this product, visit /warrantyDANGER! Sirens produce extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration () provides information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe exposure times for your specific application,operators and anyone else in the immediate vicinity should be required to wear an approved hearing protection device. Failure to follow this recommendation could cause hearing loss!•Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.•Whelen Engineering requires the use of waterproof butt splices and/or connectors if that connector could be exposed to moisture.•Any holes, either created or utilized by this product, should be made both air- and watertight using a sealant recommended by your vehicle manufacturer.•Failure to use specified installation parts and/or hardware will void the product warranty.•If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove any metal shards or remnants. Install grommets into all wire passage holes.•If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.•Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.•For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post (this does not include products that use cigar power cords).•If this product uses a remote device for activation or control, make sure that this device is located in an area that allows both the vehicle and the device to be operated safely in any driving condition.•It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.•FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!CAUTIONLoud siren noise can cause hearing damage and/or loss.Refer to OSHA Section 1910.95prior to putting ANY siren into service!Wear Protection!ACTIVATION OF THIS SIREN MAY DAMAGE UNPROTECTED EARS!Warnings to InstallersWhelen’s emergency vehicle warning devices must be properly mounted and wired in order to be effective and safe. Read and follow all of Whelen’s written instructions when installing or using this device. Emergency vehicles are often operated under high speed stressful conditions which must be accounted for when installing all emergency warning devices. Controls should be placed within convenient reach of the operator so that they can operate the system without taking their eyes off the roadway. Emergency warning devices can require high electrical voltages and/or currents. Properly protect and use caution around live electrical connections.Grounding or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or vehicle damage, including fire. Many electronic devices used in emergency vehicles can create or be affected by electromagnetic interference. Therefore, after installation of any electronic device it is necessary to test all electronic equipment simultaneously to insure that they operate free of interference from other components within the vehicle. Never power emergency warning equipment from the same circuit or share the same grounding circuit with radio communication equipment. All devices should be mounted in accordance with the manufacturer’s instructions and securely fastened to vehicle elements of sufficient strength to withstand the forces applied to the device. Driver and/or passenger air bags (SRS) will affect the way equipment should be mounted. This device should be mounted by permanent installation and within the zones specified by the vehicle manufacturer, if any. Any device mounted in the deployment area of an air bag will damage or reduce the effectiveness of the air bag and may damage or dislodge the device. Installer must be sure that this device, its mounting hardware and electrical supply wiring does not interfere with the air bag or the SRS wiring or sensors. Mounting the unit inside the vehicle by a method other than permanent installation is not recommended as unit may become dislodged during swerving; sudden braking or collision. Failure to follow instructions can result in personal injury. Whelen assumes no liability for any loss resulting from the use of this warning device. PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THE PUBLIC.Warnings to UsersWhelen’s emergency vehicle warning devices are intended to alert other operators and pedestrians to the presence and operation of emergency vehicles and personnel. However, the use of this or any other Whelen emergency warning device does not guarantee that you will have the right-of-way or that other drivers and pedestrians will properly heed an emergency warning signal. Never assume you have the right-of-way. It is your responsibility to proceed safely before entering an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes. Emergency vehicle warning devices should be tested on a daily basis to ensure that they operate properly. When in actual use, the operator must ensure that both visual and audible warnings are not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or other obstructions. It is the user’s responsibility to understand and obey all laws regarding emergency warning devices. The user should be familiar with all applicable laws and regulations prior to the use of any emergency vehicle warning device. Whelen’s audible warning devices are designed to project sound in a forward direction away from the vehicle occupants. However, because sustained periodic exposure to loud sounds can cause hearing loss, all audible warning devices should be installed and operated in accordance with the standards established by the National Fire Protection Association.Safety FirstThis document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could prevent serious injury or damage.Installation Guide:PCC10 Power Control Center51 Winthrop RoadChester, Connecticut 06412-0684Phone: (860) 526-9504Internet: Sales e-mail: autosale@Customer Service e-mail: custserv@®ENGINEERING COMPANY INC.WARNING! These switches are suitable for 20 amp, 12 volt DC applications only. Any attempt to load these switches above 20 amps will result in switch failure. Due to power supply surge, running more than one power supply per switch may result in switch failure.The control center is designed for very simple installation. The only tools required are a pocket screwdriver and a combination wire cutter/stripper/crimper tool.For standard switching, run a 10gauge positive and negative feed wire from the battery to the control center. Strip a quarter inch of insulation from both wires.Insert the positive wire into terminal block position 1. Tighten the terminal block lock screw firmly down on the wire. Insert the negative wire into terminal block position 2. Tighten the terminal block lock screw firmly down on the wire.Strip a quarter inch of insulation from all the negative wires from the items to be attached to thecontrol center. Crimp number 10 ring terminals to these wires. The negative wires can then be stacked on the number ten ground stud on the back of the box. Tighten the supplied number ten nut firmly down on the ground wires.Strip a quarter inch of insulation from all the positive feed wires on the items to be attached to the power control center. Looking at the supplied diagram, terminal block 3 is fed by switch 1, position 4 by switch 2, position 5 by switch 3, position 6 by switch 4, position 7 by switch 5, position 8 by switch 6, position 9 by switch 7, position 10 by switch 8, position 11 by switch 9 and position 12 by swich 10. Choose the proper switch and terminal block position for each item to be connected. Place the wires in the terminal block positions and tighten the block lock screws firmly down on the wires.The black wire exiting the back of the box is the power wire for the inside label light. Attach an ignition or positive wire to this wire. To prevent battery drain, be sure this light comes on only when the ignition is turned on.Take the supplied label kits and determine which label describes the function of switch 1. Peel the label off the backing and place it in the label hole above switch 1. Press it lightly into place.Continue this operation for each switch.Mount the box with the supplied bracket or to an existing bracket and the installation is complete.THE BACKLIGHT BULB IS PACKAGED SEPARATELY INSIDE THE SWITCH BOX. TO INSTALL, REMOVE THE TOP , REMOVE PROTECTIVE WRAP FROM BULB AND INSERT INTO THE SOCKET PROTRUDING FROM THE TERMINAL BLOCK.PCC Specifications•14 Gauge steel construction •Black matte powder paint •Back lighted identification labels •Single Pole/Single Throw (lit when on)•12 volt/20 amp switches •Primary wire - 10 Gauge •Secondary wire - 14 Gauge •Label light wire - 18 Gauge •Screw lock terminal block wire connections。

ICS13.220.30CCS C84中华人民共和国国家标准GB5135.2—20XX代替GB5135.2-2003自动喷水灭火系统第2部分：湿式报警阀、延迟器、水力警铃Automatic sprinkler system—Part2：Wet system alarm valves、retard chamber、water motor alarm征求意见稿20XX-XX-XX发布20XX-XX-XX实施国家市场监督管理总局前 言本文件的全部技术内容为强制性。

本文件按照GB/T1.1—2020《标准化工作导则第1部分：标准化文件的结构和起草规则》和GB/T 20001.10—2014《标准编写规则第10部分：产品标准》的规定起草。

本文件是GB5135《自动喷水灭火系统》的第2部分。

GB5135已经发布了以下部分：——第1部分：洒水喷头；——第2部分：湿式报警阀、延迟器和水力警铃；——第3部分：水雾喷头；——第4部分：干式报警阀；——第5部分：雨淋报警阀；——第6部分：通用阀门；——第7部分：水流指示器；——第8部分：加速器；——第9部分：早期抑制快速响应（ESFR）喷头；——第10部分：压力开关；——第11部分：沟槽式管接件；——第13部分：水幕喷头；——第14部分：预作用装置；——第15部分：家用喷头；——第16部分：消防洒水软管；——第17部分：减压阀；——第18部分：消防管道支吊架；——第19部分：塑料管道及管件；——第20部分：涂覆钢管；——第21部分：末端试水装置；——第22部分：特殊应用喷头。

本文件代替GB5135.2-2003《自动喷水灭火系统第2部分:湿式报警阀、延迟器和水力警铃》。

与GB5135.2—2003相比，除编辑性改动外，主要技术变化如下：——更改了规范性引用文件（见第2章，2003年版的第2章）；——更改了部分术语和定义（见第3.2、3.8、3.9，2003年版的3.2、3.8、3.9）；——增加了产品的分类与代号、型号编制（见第4章、第5章）；——更改了标志（见6.1.2，2003年版的4.1.2）；——更改了规格（见6.2，2003年版的4.2.2）；——更改了额定工作压力(见6.3，2003年版的4.2.1)——更改了“材料耐腐蚀性”（见6.4，2003年版的4.3）；——更改了结构（见6.5.1，2003年版的4.4.1）；——更改了“连接方式”（见6.6，2003年版的4.4.3）；——对“零部件”要求进行了更改，增加了阀瓣密封件（见6.7、6.8，2003年版的4.5.4）；——更改了“水力摩阻”（见6.12，2003年版的4.9）；——更改了“功能”（见6.13，2003年版的4.10）；——更改了“水力警铃”（见6.18，2003版的4.15、4.16、4.17）；——增加了部分“要求”所对应的“试验方法”（见第七章）；——更改了附录A（见附录A，2003年版的附录A）；——删除了附录B（见2003年版的附录B）请注意本文件的某些内容可能涉及专利。

Technical DataTechnical DaTa 25-10378-H August 2021 S 107D UFire Alarm Device - Sounder for indoor (type A) useEssential CharacteristicsHarmonized Technical Specification: EN54-3:2001+A1:2002+A2:2006Clause(s)Performance4.2, 4.3,5.2, 5.3 Pass 4.4, 4.5, 4.6, 5.4 Pass 5.5, 5.7, 5.8, 5.9 Pass 5.8, 5.9Pass 5.11Pass 5.12, 5.13, 5.14, 5.15Pass 5.16Pass 5.17PassTechnical DataeatonEMEA Headquarters Route de la Longeraie 71110 Morges, Switzerland Eaton.euTEL: +44 (0) 1302 321541FAX: +44 (0) 1302 303220********************************************© 2021 EatonAll Rights ReservedEaton is a registered trademark.All trademarks are property of their respective Eaton Electrical Products Ltd.Llantarnam Park Cwmbran NP44 3AWTel: +44 (0) 1633 628500Fax: +44 (0) 1633 866346in the column marked EN54-3II.All other SPL measurements are taken ‘on axis’ & are not third party verified.III. Detailed EN54-3 polar SPL measurements are available in M96-024IV. A SPL of at least 65dB(A) is achieved in at least one direction at minimum volume/voltage.I. Les tons certifiés dans le cadre de la RPC (application alarme incendie) sont indiqués dans la colonne intitulée EN54-3.II. Toutes les autres mesures NPA sont relevées « sur axe » et ne sont pas vérifiées par un tiers.III. Les mesures NPA polaires détaillées EN54-3 sont disponibles dans M96-024I. Die nach CPR (Feuermelderanwendung) zertifizierten Töne sind in Spalte EN54-3.II.Alle anderen Schalldruckmessungen wurden vom akustischen Mittelpunkt ab gelesen und von keiner unabhängigen Stelle verifiziert.III. Detaillierte Polar-SPL -Messungen gemäß EN54-3 sind erhältlich in M96-024I. I toni della sirena certificati CPR (applicazione allarme antincendio) sono indicate nella colonna contrassegnata con EN54-3.II.Tutte le altre misurazioni SPL sono state rilevate “sull’asse” e non sono state verificate da terzi.III. Le misurazioni SPL polari ai sensi della norma EN54-3 sono disponibili in M96-024kolom waar EN54-3 staat vermeld.II. Alle andere SPL -afmetingen zijn via de ‘as’ gedaan en niet door derden geverifieerd.III. Uitgebreide polaire SPL -afmetingen voor EN54-3 zijn beschikbaar in M96-024I. Los sonidos certificados por el CPR (aplicación para alarmas de incendios) se muestran en la columna marcada con EN54-3.II.Cualquier otra medida del SPL (nivel de intensidad acústica) se toma “sobre el eje” y no está verificada por terceras partes.III. Las medidas detalladas del SPL polar EN54-3 están disponibles en M96-024I. Signaler som är certifierade för CPR (brandvarnare) visas i kolumnen märkt EN54-3.II.Alla övriga mätningar av ljudtrycket har genomförts “direkt intill” och är inte bekräftade av tredje part.III. Detaljerade polära mätningar av ljudtrycket enligt EN54-3 finns under M96-024I. Sygnały d źwiękowe zgodne z CPR (do zastosowań pożarowych) wskazane są w kolumnie EN54-3.II.Pomiary SPL wszystkich pozostałych sygnałów zostały wykonane …w osi” i nie były poddane weryfikacji przez stronę trzecią.III. Szczegółowe dane pomiarów kątowych SPL wg EN54-3 dostępnesą w dokumencie M96-024.。

273 Branchport Ave.Long Branch, NJ 07740 Thank you for using our products.(800) 631-2148 INSTALLATION INSTRUCTIONSUNIVERSAL TELEPHONE ALERTUse this product according to this instruction manual. Please keep this instruction manual for future reference.MODEL: UTA-1GENERAL INFORMATION:The UTA is a loud attention getting electronic ringer designed for use in noisy locations or for wide area coverage. It is FCC and DOC Registered for the public telephone network and can be used behind PBX and key systems that use interrupted ring voltages from 40-130V, 20-30Hz or 18-30VDC/VAC or 36-60VDC.The UTA, when used indoors, will accommodate a modular plug that mates with an RJ-11C jack (USA) or a CA-11 jack (Canada) for ringing voltage. UTA operates directly off the telephone ringing voltage with low current drain to minimize line loading.UTA offers a choice of four selectable sound patterns (horn, bell, single chime or vibrating chime) with a volume control. The UTA is equipped with a weather resistant backbox for optional outdoor use with conduit enclosed wiring.APPLICATION INFORMATION:The installation of this product must conform to the following instructions. IF ANY WORDS OR LETTERS APPEAR ON THE PRODUCT INDICATING A PARTICULAR USE, THE PRODUCT MUST BE USED ONLY IN THE MANNER SO INDICATED. FIELD ADJUSTMENT, REPAIR OR MODIFICATION OF THESE SIGNALS SHOULD NOT BE ATTEMPTED. Malfunctioning units should be returned for factory repair or replacement inCAUTIONS and WARNINGS: The installation of this equipment should only be undertaken by qualified personnel.FCC REGULATIONS:•This equipment complies with Part 68 of the FCC Rules. The label affixed to this product contains, among other information, the FCC Registration Number and the Ringer Equivalence Number (REN) for this product. This information must be provided to the telephone company if requested. •The REN is used to determine the quantity of devices which you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN's of all devices connected to one line should not exceed five (5.0).To be certain of the number of devices that you may connect to your line, contact your local telephone company.•This equipment should not be used on coin telephone lines. Connection to party line service is subject to state tariffs.•If trouble is experienced, disconnect this equipment from the telephone line to determine if it is causing the malfunction. If the equipment is determined to be malfunctioning, its use shall be discontinued until the problem has been corrected.•Should the equipment cause harm to the telephone network, the telephone company shall, if possible, notify the customer that temporary discontinuance of service may be required; however, where prior written notice is not possible, the telephone company may temporarily discontinue service without notice, if such action is necessary under the circumstances. The telephone company may make changes in its communication facilities, equipment and operations procedures, where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations of the Federal Communications Commission.INDUSTRY CANADA (IC) REGULATIONS: (Only applicable for use in Canada)•The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safetey requirements as prescribed in the appropriate Terminal Equipment Technical requirements documents(s). The Department does not guarantee the equipment will operate to the user's satisfaction.•Before installing this equipment, users should ensure that it is permissible to be connected to the facilities or the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.•Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs of alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. •Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, orRINGER EQUIVALENCE NUMBER:The Ringer Equivalence Number (REN) assigned to each terminal device provides and indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.Copyright 2011 Cooper Wheelock Inc., dba Cooper Notification. All rights reserved.SPECIFICATIONS:Table 1: Sound Output (dBA) and Current (REN) at Maximum Volume24VDC 24VAC 48VDC 90Vrms/20Hz Horn 108dB/30mA 105dB/46mA 107dB/26mA 104dB/No More 1.6 RENBell 100dB/9mA 102dB/35mA 100dB/10mA 100dB/ No More 1.4 RENVibrating Chime 96dB/6mA 99dB/29mA 94dB/7mA 97dB/ No More 1.25 RENSingle Chime 96dB/6mA 100dB/34mA 94dB/6mA 96dB/ No More 1.25 REN NOTES:1. Input Voltage Range: 24VDC = 18-30VDC, 24VAC = 18-30VAC, 48VDC = 36-60VDC, 90VRMS =40-130VRMS, 20-30Hz2. dBA is measured on-axis in a non-reflective (free field) test room using fast meter response.Table 2: Sound Output Volume Adjusting Range24VDC 24VAC 48VDC 90Vrms/20Hz Horn 108-73dB 105-76dB 107-79dB 104-83dBBell 100-61dB 102-64dB 100-67dB 100-73dBVibrating Chime 97-57dB 100-61dB 94-64dB 97-68dBSingle Chime 96-57dB 97-61dB 94-64dB 96-68dBTable 3: Tone DescriptionHorn Broadband HornBell 1560Hz Modulated (0.07 Sec. ON/RepeatVibrating Chime 700Hz (1.0 Sec. Decay/Repeat)Single Chime 700Hz (1.0 Sec. Decay)Table 4: Duty and Ring CycleCycle 90Vrms/20-30Hz 24VDC/AC, 48VDCDuty Cycle 33% Max. 100% Max.Min. Ring Cycle ON Time 0.8 Sec. 0.5 Sec.Min. Ring Cycle OFF Time 1.6 Sec. 0.5 Sec.Max. Ring Cycle ON Time 10 Sec. ContinuesUTA SETTINGS:The SW1 and SW2 switches of the UTA are used to set input voltage and desired tone as shown in Figure 2 and Table 5. The potentiometer R12 (shown in Figure 2) is used to adjust the volume of sound.The factory settings are:Input Voltage = 90Vrms/20-30Hz (SW1 POS 1 set on 0)Tone = Horn (SW2 POS 1,2,3,4 set on 0,0,1,1)Volume = MaximumTable 5: Input Voltage and Tone SelectionsSwitch SettingsInput Tone SW1 SW2Voltage POS 1 POS 1 POS 2 POS 3 POS 4Horn 1 1 0 1 124VDC Bell 1 1 0 1 0Vibrating Chime 1 1 0 0 0Single Chime 1 1 1 0 1Horn 1 0 0 1 124VAC Bell 1 1 0 1 0Vibrating Chime 1 1 0 0 0Single Chime 1 1 1 0 1Horn 1 0 0 1 148VDC Bell 1 0 0 1 0Vibrating Chime 1 0 0 0 0Single Chime 1 0 1 0 1Horn 0 0 0 1 190VAC Bell 0 0 0 1 020-30Hz Vibrating Chime 0 0 0 0 0Single Chime 0 0 1 0 1MOUNTING INFORMATION:The UTA is designed for mounting to walls, partitions or posts in both indoor and outdoor applications. Refer to Figures 1, 2 and 3 mounting, wiring and adjustment of each model. Use 4 conductor modular telephone line cords for ring voltage indoor wiring. For outdoor applications, use conduit enclosed wiring. All models are rated for indoor and outdoor use with a temperature range of -31°F to +150°F (-35°C to +66°C) and a maximum humidity of 95% RH.NOTE: Potentiometer shaft and four screws must be installed first before proceeding with Figure 1.Before mounting, test the signal by temporarily connecting it as shown. Place a call into the system to make sure the signal operates properly.HARMFUL TO YOUR HEARING. UTA’s SHOULD BE LOCATED AT LEAST 10 FEET AWAY FROM LISTENERS.mounting screw (supplied) as per diagram"bottom" hole. Tighten both screws. Forhollow or thin panels use appropriate drywall fastenersImproper connections and settings can damage the unit and/or the phone system.These devices are not intended for use in hazardous locations as defined by the National Electrical Code (NEC) and by the National ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM COOPER NOTIFICATION MANUALS OR OTHER DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT THE SOLE RISK OF THE USER AND COOPER NOTIFICATION WILL NOT HAVE ANY LIABILITY FOR SUCH USE.Check the installation instructions of the manufacturers of other equipment used in the system for any guidelines or restrictions on example, may require special precautions to assure electrical noise immunity (e.g. audio crosstalk).NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and receiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and 4) Consult the dealer or an experienced radio/TV technician for help.LIMITED WARRANTYCooper Wheelock, Inc. dba Cooper Notification and Cooper Notification, Inc. (each, a “Seller”) products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and operationally tested in accordance with these instructions at the time of installation and at least twice a year or more often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation, maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association (NFPA), Underwriter’s Laboratories (UL), National Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and other applicable building and fire standards, guidelines, regulations laws and codes including, but not limited to, all appendices and amendments and the requirements of the local authority having jurisdiction (AHJ). Seller products when properly specified, applied, installed, operated, maintained and operationally tested as provided above are warranted against mechanical and electrical defects for a period of (a) three (3) years from date of manufacture with respect to MEDC and Seller Industrial Signals and Seller Fire and Security Notification Appliances and Devices, or (b) one (1) year from date of manufacture with respect to Waves and SafePath Voice Evacuation and Mass Notification Systems (date of manufacture is determined by date code.) Correction of defects by repair or replacement shall be at Seller’s sole discretion and shall constitute fulfillment of all obligations under this warranty. THE FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE EVENT ANY PART NOT FURNISHED BY SELLER IS INSTALLED IN THE PRODUCT. THE FOREGOING LIMITED WARRANTY SPECIFICALLY EXCLUDES ANY SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A PRODUCT. SELLER MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY WHETHER AS TO MECHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER.USERS ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER’S PURPOSES, OR WHETHER IT WILL ACHIEVE THE USER’S INTENDED RESULTS. THERE IS NO WARRANTY AGAINST DAMAGE RESULTING FROM MISAPPLIACATION, IMPROPER SPECIFICATION, ABUSE, ACCIDENT OR OTHER OPERATING CONDITIONS BEYOND SELLER’S CONTROL.SELLER DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE OR THAT THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE, OR THAT THE FUNCTIONS OR PERFORMANCE OF THE SOFTWARE WILL MEET THE USER’S REQUIREMENTS. SELLER SHALL NOT BE LIABLE FOR ANY DELAYS, BREAKDOWNS, INTERRUPTIONS, LOSS, DESTRUCTION, ALTERATION, OR OTHER PROBLEMS IN THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE.THE LIABILITY OF SELLER ARISING OUT OF THE SUPPLYING OF A PRODUCT, OR ITS USE, WHETHER ON WARRANTIES, NEGLIGENCE, OR OTHERWISE, SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING DEFECTS AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL SUCH LIABILITY SHALL TERMINATE. SELLER IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL, REINSTALLATION OR REPAIR OF A PRODUCT BY ANYONE OTHER THAN SELLER OR FOR DAMAGE OF ANY TYPE WHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOSS OF PROFIT OR INCIDENTAL, INDIRECT, CONSEQUENTIAL, SPECIAL, PUNTIVE OR EXEMPLARY DAMAGES. THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE EXCLUSIVE LIABILITY OF SELLER.IN NO CASE WILL SELLER’S LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT.LIMITATION OF LIABILITYSELLER’S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING NEGLIGENCE AND BREACH OF WARRNTY, FOR ANY LOSS OR DAMAGE RESULTING FROM, ARISING OUT OF, OR CONNECTED WITH THIS CONTRACT, OR FROM THE MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR OR USE OF ANY PRODUCT COVERED BY THIS ORDER SHALL BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE TO THE CLAIM. SELLER’S LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE INSTALLATION IN THE PRODUCT OF ANY PART NOT FURNISHED BY SELLER. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY CLAIM OF ANY KIND UNLESS IT IS PROVEN THAT ITS PRODUCT WAS THE DIRECT CAUSE OF SUCH CLAIM. FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF NEGLIGENCE, SHALL SELLER BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL, SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING LIMITATION MAY NOT APPLY TO ALL PURCHASERS.8/11。

幼儿园安全警报器使用指南：教学手册幼儿园安全警报器使用指南：教学手册随着幼儿园教育的不断发展，幼儿园安全成为了备受关注的话题。

在幼儿园中，安全警报器的使用至关重要，它可以在紧急情况下及时提醒教职员工和家长们，确保幼儿园的安全。

本文将深入探讨幼儿园安全警报器的使用指南，为教职员工提供专业的教学手册。

一、规范使用准则1. 对警报器的基本了解在教学手册中，必须首先对安全警报器的基本原理和使用方法进行介绍。

工作人员在紧急情况下应该如何触发警报器，以及触发后应该采取的措施，这些都是必不可少的知识。

2. 规范操作流程教学手册需要详细列出警报器的操作流程，包括启动警报器、紧急联系人的通知、学生疏散的指导等。

规范的操作流程可以有效提高应急反应的效率，保障幼儿园在紧急情况下的安全。

二、训练与演练1. 定期演练安全警报器的使用需要进行定期的演练，以确保教职员工能够熟练掌握操作流程。

在教学手册中可以列出演练的时间表和具体内容，例如模拟火灾、自然灾害等紧急情况，让工作人员能够快速而准确地进行应对。

2. 演练记录和总结每次演练后都需要对演练情况进行记录和总结，教学手册应当详细描述记录的形式和内容。

通过记录和总结，可以及时发现问题，并及时进行纠正和改进，提高教职员工的应急处置能力。

三、现场应用实例1. 分类应用教学手册可以提供各种紧急情况下的现场应用实例，例如火灾、入侵、自然灾害等。

在面对不同的紧急情况时，工作人员应该采取对应的操作流程和措施，因此现场应用实例的提供对于教职员工的应急反应能力提升至关重要。

2. 成功案例与失败案例通过共享成功的应用案例和失败的案例，教学手册可以帮助教职员工更好地理解警报器的使用，并且警示工作人员应该注意哪些问题。

这种实例的共享和讨论可以帮助工作人员更好地理解如何正确、高效地使用安全警报器。

个人观点和理解在我看来，幼儿园安全警报器的使用是非常重要的。

作为工作人员，我们必须时刻保持警惕，掌握安全警报器的使用方法，并且要通过定期的演练和总结，不断提高自身的应急处理能力。