HLMP-K105-NN0A2中文资料

F-PCHPCH / PCH-WG: V 119568 Z E82292Contact data PCH PCH-WGContact configuration 1 CO or 1 NOContact set single contactType of interruption micro-disconn.Rated current5ARated voltage / max.switching voltage AC250/400VACMaximum breaking capacity AC 1250VAContact material AgSnOMechanical endurance 1.5x106cycles10x106cyclesRated frequency of operation with / without load 6/600min-1Contact ratingsType Load CyclesPCH-XXXX2M-WG N/O, 5 A, 250VAC, 85°C, resistive, EN61810-1100x103PCH-XXXX2-WG C/O (N/O tested): 5 A, 250VAC, 85°C, res. EN61810-1100x103PCH-XXXD2M N/O, 5 A, 250VAC, 70°C, resistive, EN61810-1100x103PCH-XXXL2M N/O, 5 A, 250VAC, 70°C, resistive, EN61810-130x103PCH-XXXD2C/O, 3 A, 250VAC, 40°C, resistive, EN61810-130x103Coil data standard sensitivRated coil voltage range DC coil 5...48 VDC 5...24 VDCCoil power DC coil typ. 400mW typ. 200 mWOperative range 1Coil insulation system according UL1446 class FCoil versions,DC-coil - standardcode voltage voltage voltage resistance powerVDC VDC VDC Ohm mW055 3.750.562.5+10%400066 4.50.680+10%400099 6.30.9202.5+10%40012128.4 1.2360+10%400242416.8 2.41440+10%400484833.6 4.85760+10%400All figures are given for coil without preenergization, at ambient temperature +23°COther coil voltages on requestPCB layout/terminal assignmentBottom view on solder pinsDimensionsS0550-AAS0550-ABS0550-ACS0551ACoil versions,DC-coil - sensitiveCoil Rated Operate Release Coil Rated coilcode voltage voltage voltage resistance powerVDC VDC VDC Ohm mW055 3.750.5125+10%200066 4.50.6180+10%200099 6.750.9400+10%20012129.0 1.2720+10%200242418.0 2.42800+10%200All figures are given for coil without preenergization, at ambient temperature +23°COther coil voltages on requestInsulation PCH PCH-WGrmsopen contact circuit1000 V rmsN/O: 5.5 / 9mmC/O: 4.5 / 9mmMaterial group of insulation parts IIIaTracking index of relay base PTI 175PTI 250Insulation to IEC 60664-1Type of insulation coil-contact circuit basicopen contact circuit functionalRated insulation voltage250VPollution degree23Rated voltage system 250VOvervoltage category IIIOther data PCH PCH-WGRoHS - Directive 2002/95/EC compliant as per product date code 0424GWIT to IEC 60695-2-13775°CFlammability class according to UL94 V0Ambient temperature rangeall WG-versions:-40...85°CStandard N/O:-30...70°CStandard C/O:-30...40°COperate- / release time typ. 10/5msBounce time N/O / N/C contact typ. 1 / 3 msVibration resistance (function) NO / NC contact>14/8g, 30...400HzShock resistance (destruction) 100gCategory of protection RTII - flux proofRTIII - wash tightMounting PCBwash-tight version260°C/5sRelay weight7gPackaging unit25/1000pcs。

原理框图
V+IN
13
4
RG
3
VI–N
2
VLIN IR1
12 1
IR2 14
800µA 800µA
RLIN 1kΩ
100µA
VREG V+
11
10 5.1V
B
9
Q1
I = 100µA + VIN RG 975Ω
E 8
25Ω
7
I = 4mA + V •
( ) 40
O
IN
RG
6
IRET
引脚分配
Top View
5.35 5.30
VREG 输出电压 vs VREG 输 出 电 流 125°C
5.25
25°C
5.20
5.15 –55°C
5.10
5.05
NOTE: Above 1mA, Zero Output Degrades
5.00
–1.0 –0.5
0
0.5
1.0
1.5
2.0
VREG 输出电流 (mA)
20 30 2.6
±25 ±0.5 0.2
in Volts, G in Ω R
±50 ±0.9
单位
A mA mA mA
mA µA µA/°C µA/V µA/V µA/mA µAPP
S = 40/RG
±0.05
±0.2
±3
±25
0.003
0.01
±50
±100
±0.4
±1.5
±0.3
±3
±10
±50
1.25
3.5
5
25
20

广饶耐磨输送带参数
广饶耐磨输送带是一种用于输送物料的传送带，广泛应用于煤矿、钢铁、建材、化工等行业。

以下是广饶耐磨输送带的主要参数：
1. 带宽：通常为500mm、650mm、800mm、1000mm、1200mm等。

2. 带材：由耐磨橡胶、聚酯纤维等材料制成。

3. 厚度：一般为5mm-30mm，具体厚度可根据实际使用需求定制。

4. 强度：通常分为PN100、PN125、PN150、PN200等等级。

5. 抗拉强度：一般在10MPa以上。

6. 耐磨性能：耐磨性能好，可在重载、高速条件下长期使用。

7. 密度：一般在1.2-1.5g/cm之间。

8. 适用温度：一般在-40℃~+80℃范围内。

9. 抗拉伸变形率：一般在≤4%左右。

以上是广饶耐磨输送带的主要参数，具体选型需根据实际使用要求和环境条件进行选择。

- 1 -。

AgilentT-13/4 (5 mm), T-1 (3 mm),High Intensity, Double Heterojunction AlGaAs Red LED LampsData SheetHLMP-D101/D105, HLMP-K101/K105DescriptionThese solid state LED lamps utilize newly developed doubleheterojunction (DH) AlGaAs/GaAs material technology. This LED material has outstanding lightoutput efficiency over a wide rangeFeatures• Exceptional brightness • Wide viewing angle• Outstanding material efficiency • Low forward voltage • CMOS/MOS compatible • TTL compatible • Deep red colorApplications• Bright ambient lighting conditions • Moving message panels • Portable equipment • General useof drive currents. The color is deep red at the dominantwavelength of 637 nanometres.These lamps may be DC or pulse driven to achieve desired light output.Package DimensionsA B CSelection GuideLuminous IntensityIv (mcd) at 20 mA2θ1/2[1]Package Package Description Device HLMP-Min.Typ.Max.Degree Outline T-1 3/4 Red Tinted Diffused D10135.270.0–65AD101-J00xx35.270.0–65AD101-JK0xx35.270.0112.865AT-1 3/4 Red Untinted Non-diffused D105138.0240.0–24BD105-M00xx138.0240.0–24BD105-NO0xx200.0290.0580.024BT-1 Red Tinted Diffused K10122.045.0–60CK101-100xx22.045.0–60CK101-IJ0xx22.045.070.460CT-1 Red Untinted Non-diffused K10535.265.0–45CK105-J00xx35.265.0–45CK105-KL0xx56.4110.0180.445CNote:1. θ1/2 is the off axis angle from lamp centerline where the luminous intensity is 1/2 the on-axis value.Part Numbering SystemHLMP - x x xx - x x x xxMechanical Option00: Bulk01: Tape & Reel, Crimped Leads02: Tape & Reel, Straight LeadsA1: Right Angle Housing, Uneven Leads, T1A2: Right Angle Housing, Even Leads, T1B1: Right Angle Housing, Uneven Leads, T-1 3/4B2: Right Angle Housing, Even Leads, T-1 3/4DD, UQ: Ammo PackColor Bin Options0: Full Color Bin DistributionMaximum Iv Bin Options0: Open (no max. limit)Others: Please refer to the Iv Bin TableMinimum Iv Bin OptionsPlease refer to the Iv Bin TableLens Type01: Tinted, Diffused05: Untinted, NondiffusedColor Options1: AlGaAs RedPackage OptionsD: T-1 3/4K: T-1Absolute Maximum Ratings at T A = 25°CParameter ValuePeak Forward Current[1,2]300 mAAverage Forward Current[2]20 mADC Current[3]30 mAPower Dissipation87 mWReverse Voltage (I R = 100 µA) 5 VTransient Forward Current (10 µs Pulse)[4]500 mALED Junction Temperature110°COperating Temperature Range-20 to +100°C Storage Temperature Range-55 to +100°C Wave Soldering Temperature [1.59 mm (0.063 in.) from body]250°C for 3 seconds Lead Solder Dipping Temperature [1.59 mm (0.063 in.) from body]260°C for 5 seconds Notes:1.Maximum I PEAK at f = 1 kHz, DF = 6.7%.2.Refer to Figure 6 to establish pulsed operating conditions.3.Derate linearly as shown in Figure 5.4.The transient peak current is the maximum non-recurring peak current the device can withstand without damaging the LED die and wire bonds. It isnot recommended that the device be operated at peak currents beyond the Absolute Maximum Peak Forward Current.Electrical/Optical Characteristics at T A = 25°CSymbol Description Min.Typ.Max.Unit Test ConditionV F Forward Voltage 1.8 2.2V I F = 20 mAV R Reverse Breakdown Voltage 5.015.0V I R = 100 µAλp Peak Wavelength645nm Measurement at Peakλd Dominant Wavelength637nm Note 1∆λ1/2Spectral Line Halfwidth20nmτS Speed of Response30ns Exponential TimeConstant, e-t/T SC Capacitance30pF V F = 0, f = 1 MHzRθJ-PIN Thermal Resistance260[3]°C/W Junction to Cathode Lead210[4]290[5]ηV Luminous Efficacy80Im/W Note 2Notes:1.The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the color of the device.2.The radiant intensity, I e, in watts per steradian, may be found from the equation I e = l V/ηV, where I V is the luminous intensity in candelas and ηV isluminous efficacy in lumens/watt.3.HLMP-D101.4.HLMP-D105.5.HLMP-K101/-K105.Figure 3. Relative luminous intensity vs. dc forward current.Figure 4. Relative efficiency vs. peak forward current.Figure 7. Relative luminous intensity vs. angular displacement. HLMP-D101.Figure 8. Relative luminous intensity vs. angular displacement. HLMP-K101.Intensity Bin LimitsIntensity Range (mcd)Color Bin Min.Max.Red I24.839.6J39.663.4K63.4101.5L101.5162.4M162.4234.6N234.6340.0O340.0540.0P540.0850.0Q850.01200.0R1200.01700.0S1700.02400.0T2400.03400.0U3400.04900.0V4900.07100.0W7100.010200.0X10200.014800.0Y14800.021400.0Z21400.030900.0Maximum tolerance for each bin limit is ± 18%.Mechanical Option MatrixMechanical Option Code Definition00Bulk Packaging, minimum increment 500 pcs/bag01Tape & Reel, crimped leads, minimum increment 1300 pcs (T-1 3/4)/1800 pcs (T-1) 02Tape & Reel, straight leads, minimum increment 1300 pcs (T-1 3/4)/1800 pcs (T-1) A1Right Angle Housing, uneven leads, minimum increment 500 pcs/bagA2Right Angle Housing, even leads, minimum increment 500 pcs/bagB1Right Angle Housing, uneven leads, minimum increment 500 pcs/bagB2Right Angle Housing, even leads, minimum increment 500 pcs/bagDD Ammo Pack, straight leads in 2K incrementUQ Ammo Pack, horizontal leads in 2K incrementNote:All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information./semiconductors For product information and a complete list of distributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152 (Domestic/Interna-tional), or 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843Data subject to change.Copyright © 2004 Agilent Technologies, Inc. Obsoletes 5968-1440ENovember 12, 20045988-2230EN。