ICND110S00

AEC - Q100-001 - REV-COctober 8, 1998 Automotive Electronics CouncilComponent Technical CommitteeATTACHMENT 1AEC - Q100-001 REV-CWIRE BOND SHEAR TESTAEC - Q100-001 - REV-COctober 8, 1998 Automotive Electronics CouncilComponent Technical CommitteeAcknowledgmentAny document involving a complex technology brings together experience and skills from many sources. The Automotive Electronics Counsel would especially like to recognize the following significant contributors to the development of this document:James T. Peace DaimlerChryslerRobert V. Knoell Visteon CorporationGerald E. Servais Delphi Delco Electronics Systems - RetiredMark A. Kelly Delphi Delco Electronics SystemsOctober 8, 1998 Automotive Electronics CouncilComponent Technical CommitteeChange NotificationThe following summary details the changes incorporated into AEC-Q100-001 Rev-C:•Section 1.3.4.4, Type 4 - Die Surface Contact: Corrected wording to reflect bond shear type where the shear tool contacts the die surface, rather than the bonding surface asstated in Rev - B.•Added new Section 1.3.5, Footprint: Added new definition for “footprint”; changed numbers of subsequent sections to reflect the addition.•Section 3.6 step b, Footprint Inspection of Aluminum Wedge/Stitch Bonds: Added wording to clarify method used to remove wire for footprint inspection.•Figure 3, Wire Bond Shear Types: Updated figure to reflect wording correction made to Type 4 - Die Surface Contact.•Minor wording changes were made to the following: Section 1.1, 1.3.1, 1.3.4.1, 1.3.4.5, 2.2,2.5,3.2, and 3.5.Component Technical CommitteeMETHOD - 001WIRE BOND SHEAR TESTText enhancements and differences made since the last revision of thisdocument are shown as underlined areas. Several figures have also beenrevised, but changes to these areas have not been underlined.1.SCOPE1.1DescriptionThis test establishes a procedure for determining the strength of the interface between a gold ball bond and a package bonding surface, or an aluminum wedge/stitch bond and a package bonding surface, on either pre-encapsulation or post-encapsulation devices. This strength measurement is extremelyimportant in determining two features:1)the integrity of the metallurgical bond which has been formed.2)the reliability of gold and aluminum wire bonds to die or package bonding surfaces.This test method can be used only when the ball height and diameter for ball bonds, or the wire height(1.25 mils and larger at the compressed bond area) for wedge/stitch bonds, are large enough andadjacent interfering structures are far enough away to allow suitable placement and clearance (e.g.,above the bonding surface and between adjacent bonds) when performing the wire bond shear test.The wire bond shear test is destructive. It is appropriate for use in process development, processmonitoring, and/or quality assurance.1.2Reference DocumentsNot Applicable1.3Terms and DefinitionsThe terms and definitions shall be in accordance with the following sections.1.3.1Ball BondThe welding of a thin wire, usually gold, to a die bonding surface, usually an aluminum alloy bond pad, using a thermal compression or thermosonic wire bonding process. The ball bond includes the enlarged spherical portion of the wire (sometimes referred to as the nail head and formed by the flame-off and first bonding operation in thermal compression and thermosonic process), the underlying bonding surface,and the intermetallic weld interface. For the purposes of this document, all references to ball bonds are applicable to gold ball bonds on die bonding surfaces; other ball bond material combinations mayrequire a new set of failure criteria (see section 4.1).Component Technical Committee 1.3.2Bonding SurfaceEither 1) the die surface (e.g., die bond pad) or 2) the package bonding surface (e.g., plated leadframe post or finger, downbond to the flag or paddle, etc.) to which the wire is ball, wedge, or stitch bonded.1.3.3Bond ShearA process in which an instrument uses a chisel shaped tool to shear or push a ball or wedge/stitch bond off the bonding surface (see Figure 1). The force required to cause this separation is recorded and is referred to as the bond shear strength. The bond shear strength of a gold ball bond, when correlated to the diameter of the ball bond, is an indicator of the quality of the metallurgical bond between the gold ball bond and the die bonding surface metallization. The bond shear strength of an aluminumwedge/stitch bond, when compared to the manufacturer’s bond wire tensile strength, is an indicator of the integrity of the weld between the aluminum wire and the die or package bonding surface.Shear Tool h Specimen ClampTest SpecimenBondingBond Weld Area Bond C LSurface Figure 1: Bond Shear set-up1.3.4Definition of Bond Shear Types for Ball and Wedge/Stitch Bonds (see Figure 3)1.3.4.1Type 1 - Bond LiftA separation of the entire wire bond from the bonding surface with only an imprint being left on the bonding surface. There is very little evidence of intermetallic formation or welding to the bonding surface metallization.1.3.4.2Type 2 - Bond ShearA separation of the wire bond where: 1) A thin layer of bonding surface metallization remains with the wire bond and an impression is left in the bonding surface, or 2) Intermetallics remain on the bonding surface and with the wire bond, or 3) A major portion of the wire bond remains on the bonding surface.Component Technical Committee1.3.4.3Type 3 - CrateringA condition under the bonding surface metallization in which the insulating layer (oxide or interlayerdielectric) and the bulk material (silicon) separate or chip out. Separation interfaces which show pits ordepressions in the insulating layer (not extending into the bulk) are not considered craters. It should be noted that cratering can be caused by several factors including the wire bonding operation, the post-bonding processing, and even the act of wire bond shear testing itself. Cratering present prior to theshear test operation is unacceptable.1.3.4.4Type 4 - Die Surface ContactThe shear tool contacts the die surface and produces an invalid shear value. This condition may be due to improper placement of the specimen, a die surface not parallel to the shearing plane, a low shearheight, or instrument malfunction. This bond shear type is not acceptable and shall be eliminated fromthe shear data.1.3.4.5Type 5 - Shearing SkipThe shear tool removes only the topmost portion of the ball or wedge/stitch bond. This condition may be due to improper placement of the specimen, a die surface not parallel to the shearing plane, a high shear height, or instrument malfunction. This bond shear type is not acceptable and shall be eliminated from the shear data.1.3.4.6Type 6 - Bonding Surface LiftA separation between the bonding surface metallization and the underlying substrate or bulk material.There is evidence of bonding surface metallization remaining attached to the ball or wedge/stitch bond.1.3.5FootprintAn impression of the compressed wedge/stitch bond area created in the bonding surface during theultrasonic wire bonding process. The bond footprint area is normally larger than the actual metallurgical weld interface.1.3.6Shear Tool or ArmA tungsten carbide, or equivalent, chisel with specific angles on the bottom and back of the tool toinsure a shearing action.1.3.7Wedge/Stitch BondThe welding of a thin wire, usually aluminum, to a die or package bonding surface using an ultrasonicwire bonding process. The wedge bond, sometimes referred to as a stitch bond, includes thecompressed (ultrasonically bonded) area of the bond wire and the underlying bonding surface. Whenwedge/stitch bonding to an aluminum alloy bonding surface, no intermetallic exists because the twomaterials are of the same composition; but rather the two materials are combined and recrystallized bythe ultrasonic energy of the welding process. For the purposes of this document, all references towedge/stitch bonds are applicable to aluminum wedge/stitch bonds only; gold wedge/stitch bonds arenot required to be wire bond shear tested.Component Technical Committee2.APPARATUS AND MATERIALThe apparatus and materials required for wire bond shear testing shall be as follows:2.1Inspection EquipmentAn optical microscope system or scanning electron microscope providing a minimum of 30Xmagnification.2.2Measurement EquipmentAn optical microscope or measurement system capable of measuring the wire bond diameter to within ±0.1 mil.2.3WorkholderFixture used to hold the device being tested parallel to the shearing plane and perpendicular to theshear tool. The fixture shall also eliminate device movement during wire bond shear testing. If using a caliper controlled workholder, place the holder so that the shear motion is against the positive stop ofthe caliper. This is to insure that the recoil movement of the caliper controlled workholder does notinfluence the wire bond shear test.2.4Wire Bond Shear EquipmentThe wire bond shear equipment must be capable of precision placement of the shear tool approximately0.1 mil above the topmost part of the bonding surface. This distance (h) shall insure the shear tool doesnot contact the die or package bonding surface and shall be less than the distance from the topmostpart of the bonding surface to the center line (C L) of the ball or wedge/stitch bond.2.5Bond Shear ToolRequired shear tool parameters include but are not limited to: flat shear face, sharp shearing edge, and shearing width of 1.5 to 2 times (1.5X to 2X) the bond diameter or bond length. The shear tool should be designed to prevent plowing and drag during wire bond shear testing. The shear tool should be cleanand free of chips (or other defects) that may interfere with the wire bond shear test.3.PROCEDURE3.1CalibrationBefore performing the wire bond shear test, it must be determined that the equipment has beencalibrated in accordance with the manufacturer's specifications and is presently in calibration.Recalibration is required if the equipment is moved to another location.Component Technical Committee3.2Visual Examination of Wire Bonds to be Shear Tested After DecapsulationBefore performing wire bond shear testing on a device which has been opened using wet chemicaland/or dry etch techniques, the bonding surfaces shall be examined to insure there is no absence ofmetallization on the bonding surface area due to chemical etching. Ball or wedge/stitch bonds onbonding surfaces with evidence of degradation from chemical attack or absence of metallization shallnot be used for wire bond shear testing. Wire bonds on bonding surfaces without degradation fromchemical attack may not be attached to the bonding surface due to other causes (e.g., packagestress). These wire bonds are considered valid and shall be included in the shear data as a zero (0)gram value. Wire bonds must also be examined to ensure adjacent interfering structures are far enough away to allow suitable placement and clearance (above the bonding surface and between adjacent wire bonds) when performing the wire bond shear test.3.3Measurement of the Ball Bond Diameter to Determine the Ball Bond Failure CriteriaOnce the bonding surfaces have been examined and prior to performing wire bond shear testing, thediameter of all ball bonds (from at least one representative sample to be tested) shall be measured and recorded. For asymmetrical ball bonds, determine the average using both the largest (d large) and the smallest diameter (d small) values (see Figure 2). These ball bond diameter measurements shall beused to determine the mean, or average, diameter value. The resulting mean, or average, ball bonddiameter shall then be used to establish the failure criteria as defined in section 4.1. If process-monitor data has established the nominal ball bond diameter, then that value may be used to determine thefailure criteria as defined in section 4.1.SYMMETRICALASYMMETRICALFigure 2: Ball bond diameter measurement (symmetrical vs. asymmetrical)Component Technical Committee3.4Wire Bond Shear Test ProcedureThe wire bond shear testing procedure shall be performed as follows:a.The wire bond shear equipment shall pass all self diagnostic tests prior to performing the wirebond shear test.b.The wire bond shear equipment and test area shall be free of excessive vibration or movement.Examine the shear tool to verify it is in good condition and is not bent or damaged. Check theshear tool to verify it is in the up position.c.Adjust the workholder to match the device being tested. Secure the device to the workholder.Make sure the die or package bonding surface is parallel to the shearing plane of the shear tool.It is important that the shear tool does not contact the bonding surface or adjacent structuresduring the shearing operation as this will give incorrect high readings.d.Position the device so that the wire bond to be tested is located adjacent to the shear tool.Lower the shear tool (or raise the device depending upon wire bond shear equipment used) toapproximately the die or package bonding surface but not contacting the surface (approximatelythe thickness of the wire bond above the die or package bonding surface).e.For ball bond shear testing, position the ball bond to be tested so that the shear motion willtravel perpendicular to the die edge. Wire bond shear testing is required for ball bonds locatedat the die bonding surface interface only.f.For aluminum wedge/stitch bond shear testing, a wire height at the compressed bond area of1.25 mils and larger is required. For wires too small for wire bond shear testing (less than 1.25mils in height at the compressed bond area), only a footprint inspection is required (see section3.6). Position the wedge/stitch bond to be tested so that the shear motion will travel toward thelong side of the wedge/stitch bond and is free of any interference (i.e. shear the outsidewedge/stitch bond first and then shear toward the previously sheared wedge/stitch bond). Wirebond shear testing is required for aluminum wedge/stitch bonds located at die and packagebonding surfaces; gold wedge/stitch bonds are not required to be wire bond shear tested.g.Position the shear tool a distance of approximately one ball bond diameter (or one aluminumwire diameter for wedge/stitch bonds) from the wire bond to be shear tested and shear the wirebond.3.5Examination of Sheared Wire BondsAll wire bonds shall be sheared in a planned/defined sequence so that later visual examination candetermine which shear values should be eliminated due to an improper shear. The wire bonds shall be examined using at least 30X magnification to determine if the shear tool skipped over the wire bond(type 5) or the shear tool scraped or plowed into the die surface (type 4). See Figure 3 for bond shear types and illustrations.Readings in which either a bond shear type 4 or 5 defective shear condition occurred shall be eliminated from the shear data. Bond shear type 1, 2, 3, and 6 shall be considered acceptable and included in the shear data.Component Technical CommitteeSheared wire bonds in which a bond shear type 3 cratering condition has occurred shall be investigated further to determine whether the cracking and/or cratering is due to the wire bonding process or the act of wire bond shear testing. Cratering caused prior to the wire bond shear test operation isunacceptable. Cratering resulting from the act of wire bond shear testing shall be consideredacceptable and included in the shear data.3.6Footprint Inspection of Aluminum Wedge/Stitch Bondsa.All aluminum wire bonding processes to both die and package bonding surfaces shall have abond footprint inspection performed.b.For wires too small for wire bond shear testing (less than 1.25 mils in height at the compressedbond area), the wires shall be removed at the wedge/stitch bond location using a small sharpblade to peel or pluck the wire bond from the bonding surface. The removal of the aluminumwire shall be sufficient such that the wire bond interface can be visually inspected and themetallurgical wire bond area determined.c.For larger wires (greater than 1.25 mils in height at the compressed bond area), the wires shallbe inspected after wire bond shear testing to examine the failure mode and to determine thewedge/stitch bond footprint coverage.3.7Bond Shear DataData shall be maintained for each wire bond sheared. The data shall identify the wire bond (location,ball bond and/or wire diameter, wire material, method of bonding, and material bonded to), the shearstrength, and the bond shear type (as defined in section 1.3.4 and Figure 3).4.FAILURE CRITERIAThe following failure criteria are not valid for devices that have undergone environmental stress testing or have been desoldered from circuit boards.4.1Failure Criteria for Gold Ball BondsThe gold ball bonds on a device shall be considered acceptable if the minimum individual and sampleaverage ball bond shear values are greater than or equal to the values specified in Figure 4 and Table 1.This criteria is applicable for gold wire ball bonds on aluminum alloy bonding surfaces. Other material combinations may require a new set of failure criteria.Alternate minimum ball bond shear values may be proposed by the supplier if supporting data justifies the proposed minimum values.4.2Failure Criteria for Aluminum Wedge/Stitch BondsThe aluminum wedge/stitch bonds on a device shall be considered acceptable if the minimum shearvalues are greater than or equal to the manufacturer’s bond wire tensile strength.In addition, the percent of the wedge/stitch bond footprint in which bonding occurs shall be greater than or equal to 50%. If it is necessary to control the wire bonding process using SPC for percent coverage,a C pk value can be calculated to this limit.Component Technical CommitteeComponent Technical CommitteeMINIMUM SHEAR VALUESBALL BOND DIAMETER (mils)2.25 2.53.0 3.25 3.5 3.754.25 4.5 4.755.0 5.252.0S H E A R S T R E N G T H (g r a m s )1.7501020304050607080901001102.75 4.0Figure 4: Minimum acceptable individual and sample average ball bond shear values *, see Table 1for exact ball bond shear values ** (Shear values are applicable for gold wire ball bonds on aluminum alloy bonding surfaces)Component Technical CommitteeTable 1: Minimum acceptable individual and sample average ball bond shear values ** (Shear values are applicable for gold wire ball bonds on aluminum alloy bonding surfaces)Ball Bond Diameter(mils)MinimumSample Average(grams)Minimum IndividualShear Reading(grams)2.012.6 5.7 2.114.0 6.8 2.215.58.1 2.317.19.5 2.418.810.9 2.520.612.4 2.622.414.0 2.724.415.6 2.826.517.42.928.619.23.030.821.1 3.133.223.1 3.235.625.1 3.338.127.2 3.440.729.4 3.543.431.7 3.646.234.1 3.749.136.5 3.852.139.13.955.241.74.058.344.3 4.161.647.1 4.265.050.0 4.368.452.9 4.471.955.8 4.575.659.0 4.679.362.1 4.783.165.3 4.887.068.64.991.072.05.095.175.5October 8, 1998 Component Technical CommitteeAutomotive Electronics CouncilRevision HistoryRev #-A BC Date of changeJune 9, 1994May 19, 1995Sept. 6, 1996Oct. 8, 1998Brief summary listing affected sectionsInitial Release.Added copyright statement.Deleted old Sections 1.3.4, 1.3.5, 3.3, 3.9, and 5.0. Added new Sections1.3.1, 1.3.2, 1.3.6, 3.4 (steps a through g), and 3.6 (steps a through c).Revised the following: Sections 1.1, 1.2, 1.3.1, 1.3.2, 1.3.3, 1.3.4(1.3.4.1 through 1.3.4.6), 1.3.5, 1.3.6, 2.1, 2.2, 2.4, 2.5, 3.1, 3.2, 3.3, 3.4(a, b, c, d, e, f, and g), 3.5, 3.6 (a, b, and c), 3.7, 4.0, 4.1, and 4.2; Table1; Figures 1, 3, and 4.Added new Section 1.3.5. Revised the following: Sections 1.1, 1.3.1,1.3.4.1, 1.3.4.4, 1.3.4.5,2.2, 2.5,3.2, 3.5, 3.6 (b), Figure 3.。

JDF-2S/N 0005473 & UPILLUSTRATED PARTS CATALOG Designs, materials, weights, specifications, and dimensions for equipment or replacement parts are subject to change without notice.BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529-664438311.0000E 03/08 ©2005 Bunn-O-Matic Corporation DISCONTINUED VERSION Parts listed in this catalog may no longer be available.BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) All equipment other than as specified below: 2 years parts and 1 year labor.2) Electronic circuit and/or control boards: parts and labor for 3 years.3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.BrewWISE, BUNN Gourmet Ice, BUNN Pour-O-Matic, BUNN, Bunn-OMatic, Bunn-O-Matic, BUNNlink, BUNNserve, BUNN Espress, DBC, Dr. Brew, Dual, EasyClear, EasyGard, Easy Pour, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, IMIX, Infusion Series, Legendary for Quality, The Mark of Quality in Beverage Equipment Worldwide, My Café, Power-Logic, Safety-Fresh, Scale-Pro, Single, Smart Funnel, Smart Hopper, Soft Heat, SplashGard, System III, ThermoFresh, 392, AXIOM, Beverage Profit Calculator, Beverage Bar Creator, BrewLOGIC, BrewMETER, BrewWIZARD, BUNNSERVE, BUNNsource, Coffee At Its Best, Cool Froth, Digital Brewer Control, Intellisteam, Nothing Brews Like a BUNN, Pouring Profits, Pulse Wave, Quality Beverage Equipment Worldwide, Signature Series, Silver Series, Smart Heat, SmartWAVE, Tea At Its Best, The Horizontal Red Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic Corporation.238311 020608TABLE OF CONTENTSMain Frame & Covers (4)Upper Cabinet & Panels (6)Refrigeration Components (8)Compressor Components (10)Fan Assembly (12)Water Tank Assy (14)Circulation Pump & Lines (18)Product Coil & Lines (20)Dispense Platform Assy (22)Dispense Valve Assy (24)Plain Water Manifold (Early Models) (26)Plain Water Manifold (Late Models) (28)Rinse Water Manifold & Solenoid (Early Models) (30)Rinse Water Manifold & Solenoid (Late Models) (34)Pump Assy (38)Bottle Adapter Assy (40)Door Assy (42)Electrical Components (46)Refillable Container Assy (50)Numerical Index (52)338311 111706438311 050807ITEM PART NO. QTY. DESCRIPTION5* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.MAIN FRAME & COVERS1 34409.0000 1 Base Frame Assy2 26528.0000 4 Leg 03996.0000 4 Pad, Non-skid3 34410.0000 1 Frame, Refridgeration - - - - - - - -4 Screw #10-32 x4 39428.0000* 2Bracket, Rear support (Late models with Water Inlet Valve)34797.0000* 2 Bracket, Rear support (Early models prior to Water Inlet Valve) 02332.0001 8 Screw, Crimptite #6 x .25"5 38469.0001* 1 Bracket, Upper Frame6 36192.1000 1 Panel w/Decals, Right (Includes item 11) 02332.0001 3 Screw, Crimptite #6 x .25"7 34786.1000 1 Panel w/Decals, Top (Includes item 8) 02332.0001 4 Screw, Crimptite #6 x .25"8 33458.0000 1 Decal, Refridgeration ON - OFF9 36191.1000 1 Panel w/Decals, Left (Includes items 10, 11, 12 & 24) 02332.0001 3 Screw, Crimptite #6 x .25"10 33461.0001 1 Decal, Refridgerant Charge11 27442.0000 2 Decal, Warning - Moving Parts12 00986.0002 1 Decal, Warning - Electrical13 39561.0001 1 Panel, Rear 02332.0001 4 Screw, Crimptite #6 x .25"14 33645.0000 1 Decal, Main Water Connection15 33646.0000 1 Decal, Rinse Water Connection (Early Models)16 00656.0000 1 Decal, Comply To Plumbing Code17 27354.0000 4 Bushing18 00668.0000 3 Plug19 35998.0001 1 Panel, Splash 01317.0003 2 Screw, Truss Head, Locking #8-32 x .38"20 21436.0000 2 Catch, Magnetic21 33538.0000*1 Bracket, Right33539.0000* 1 Bracket, Left 01311.0001 4 Screw, Truss Head, Locking #8-32 x .25"22 38765.1000 1 Drip Tray Assy (Includes strike plate and item 23)23 26801.0000 1 Grate, Drip Tray24 35277.0000 1 Schematic, Electrical38311 121207638311 111706ITEM PART NO. QTY. DESCRIPTION7* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.UPPER CABINET & PANELS1 35478.0000* 1 Cabinet (Not serviced) 24544.0000 10 Screw, Pan Head #8-182 34738.0000 1 Plate, Cabinet Mounting 01311.0001 4 Screw, Truss Head #8-32 x .25" Lkg.3 34784.0000 1 Plate, Bottom Closure 01359.0000 3 Screw, Flat Head #8-32 x .38"4 34362.0000 1 Bushing, Lower Hinge5 34790.0000 1 Wrap 01311.0001 4 Screw, Truss Head #8-32 x .25" Lkg.6 34785.0000* 1 Bracket, Hinge 01327.0000 3 Screw, Pan Head #10 -32 x .38"7 34666.0001 1 Catch, Door Latch 01382.0000 2 Screw, Truss Head #6 x .375"8 27394.0000 2 Plug9 00669.0002 4 Plug10 34419.0000 1 Coil, Water 24544.0000 4 Screw, Pan Head #8-1811 27246.0000 1 Sensor Assy, Temperature12 33669.0000 1 Clip, Adhesive Back13 33297.0000 1 Fan Assy. 03290.0000 1 Cable Tie 38616.0000 4 Screw, Pan Head #8-1814 34421.0000* 1 Cover, Fan 24544.0000 4 Screw, Hex Head w/Washer #10-2415 34422.1000 1 Shelf, Product (Includes items 16 & 17)16 33459.0003 2 Decal, Dispense/Rinse17 32461.0000 2 Gasket, Drip18 32455.0000 2 Knob19 27394.0000 2 Plug20 35930.0000 2 Nozzle21 32848.0000 2 O-ring22 35108.1000 2 Mixer, Spiral23 38519.0000 1 Decal, Dispense Ratio24 M2568.1000 - Grease, USDA H-1 (Use when assembling items 21 & 22)38311 121207838311 062905ITEM PART NO. QTY. DESCRIPTION9* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement. 1 35164.1000 1 Air Filter2 29951.0001 1 Condenser 02335.0001 4 Screw, Crimptite #8 x .38"3 35180.0001 1 Tube (Requires brazing to install) (Not serviced)4 35386.0001 1 Tube (Requires brazing to install) (Not serviced)5 00396.0002 1 Tee (Requires brazing to install) (Not serviced)6 35385.0001 1 Tube (Requires brazing to install) (Not serviced)7 35580.0001 1 Tube (Requires brazing to install) (Not serviced)8 35175.1000 1 Filter Dryer Assy (Requires brazing to install)9 35179.0001 1 Tube (Requires brazing to install) (Not serviced)10 32776.0000 1 Accumulator11 35581.0001 1 Tube (Requires brazing to install) (Not serviced)12 - - - - - - - - 1 Compressor (See COMPRESSOR COMPONENTS) 34529.0000* 4 Washer 00901.0000 4 Nut .25"-2013 - - - - - - - - 4 Grommet14 - - - - - - - - 4 Sleeve 15 33536.0000 1 Platform 01317.0003 4 Screw, Truss Head, Locking #8-32 x .38"16 - - - - - - - - 1 Fan Assy (See FAN ASSEMBLY) 27243.0000 3 Screw #8-36 x .437"17 34418.0000* 1 Bracket 01317.0003 4 Screw, Truss Head, Locking #8-32 x .38"18 28567.0000 1 Mounting Kit (Includes four each of items 13 & 14)19 M2332.1000 - Insulation, Tube 25/50 - 1.6"ID x .50" wall x 6.0 Ft (Use as required) 20 M2336.1000 - Insulation, Tube 25/50 - 0.25"ID x .19" wall x 6.0 Ft (Use as required)REFRIGERATION COMPONENTSOrder item 1838311 0303081038311 111706ITEMPART NO.QTY.DESCRIPTION11* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.COMPRESSOR COMPONENTS- 38231.1000 1 Compressor 120V (Includes items 1 - 5) 33522.1001 1 Compressor 230V (Includes items 1 - 5) 1 38897.0000 1 Relay, Compressor 120V 38897.0001 1 Relay, Compressor 230V 2 38917.0000 1 Overload Protector 3 38916.0000 1 Retainer 4 38918.0000 1 Clip 538896.00001Cover38311 1117061238311 062905ITEMPART NO.QTY.DESCRIPTION13* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.FAN ASSEMBLY- 32204.1001 1 Fan Assy 120V (Includes items 1-4) 32204.1002 1 Fan Assy 230V (Includes items 1-4) 1 33603.0000 1 Motor Assy 120V 33603.0001 1 Motor Assy 230V 2 33602.0000 1 Blade, Fan 3 27258.0000 1 Silencer 423700.00001Nut .25"-2038311 0629051438311 111706ITEMPART NO.QTY.DESCRIPTION15* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.WATER TANK ASSY1 35165.0000 1 Tank Assy - - - - - - - - 4 Screw2 35272.1001 1 Lid Assy 24544.0000 6 Screw, Pan Head #8-183 35526.0000* 2 Bracket 02332.0001 2 Screw, Crimptite #6 x .25" 01317.0003 2 Screw, Truss Head, Locking #8-32 x .38"4 34403.1001 1 Panel Assy 00973.0000 4 Nut, Keps #6-325 33801.0000 1 Grommet6 29327.0000 1 Probe, Temperature & Dry Plug7 33801.0002 1 Grommet 7 02536.0000 1 Grommet9 02645.1000 1 Probe, Liquid Level 01522.0000 1 Washer 20203.0100 1 Lockwasher, Internal-tooth #800908.0000 1 Nut #8-32 10 21275.0004 3 Clamp .54" - .64"11 20976.0062* 1 Tube, Silicone .38" ID x 1.75" (Order item 35) 1221275.0005 1 Clamp .62" - .73" 120V 21275.0009 1 Clamp .65" - .78" 230V 13 35077.0000 1 Tee .38" Sngl. Barb 14 21275.0003 4 Clamp .57" - .70"15 34325.0003* 1 Hose, Flex .38" ID x .625" OD x 3.0" (Order item 36) 16 33623.0000 2 Elbow .38" Barb17 34325.0006* 1 Hose, Flex .38" ID x .625" OD x 2.25" (Order item 36) 18 20976.0016* 1 Tube, Silicone .38" ID x 2.75" (Order item 35) 19 33068.0000 1 Fitting .38" Barb x .25" Barb20 37809.1000 1 Pump Assy 120V (Includes items 11 - 19) 37265.0000 1 Pump Assy 230V 21 35132.0000* 1 Product Coil22 34416.0000 2 Spacer 00973.0000 4 Nut, Keps #6-32 23 03290.0000 2 Cable Tie 2432734.00016Cable Tie, 28.0"(Continued)38311 0508071638311 111706ITEMPART NO.QTY.DESCRIPTION17* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.WATER TANK ASSY25 33533.0000* 4 Spacer 26 33519.0000* 1 Evaporator Coil 27 36448.0000 2 Spacer 28 03290.0000 2 Cable Tie29 33670.0004* 1 Tube, Clear .25" x 8.0" (Not serviced) 30 38605.0000 1 Tee31 21275.0006 1 Clamp .40" - .50" 32 35174.0000 1 Fitting 33 33149.0000 1 Gasket 34 00976.0000 1 Cap35 35106.0000 1 Manifold, Return Water36 20976.1000 1 Tube, Silicone .38" ID x 12.0" (Cut to required length) 20976.1001 1 Tube, Silicone .38" ID x 36.0" (Cut to required length) 20976.1002 1 Tube, Silicone .38" ID x 120.0" (Cut to required length) 37 34325.1000 1 Hose, Flex .38" ID x .625" OD x 12.0" (Cut to required length) 34325.1001 1 Hose, Flex .38" ID x .625" OD x 36.0" (Cut to required length)34325.10021Hose, Flex .38" ID x .625" OD x 120.0" (Cut to required length)38311 1117061838311 062905ITEMPART NO.QTY.DESCRIPTION19* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.1 - - - - - - - - 1 Coil, Upper Cabinet (See UPPER CABINET & PANELS)2 34325.0004* 2 Tube, Silicone .38" ID x 1.5" (Order item 10)3 21275.0003 8 Clamp .57" - .70"4 37850.0000 2 Elbow .38" Barb5 34325.0010* 1 Tube, Silicone .38" ID x 17.0" (Order item 10)6 34325.0021* 1 Tube, Silicone .38" ID x 8.0" (Order item 10)7 35173.0001 1 Fitting .312" Fl x .375" Barb8 35305.0000 1 Gasket9 - - - - - - - - 1 Manifold, Return Water (See WATER TANK ASSEMBLY) 10 34325.1000 - Tube, Silicone .38" ID x 12.0" (Cut to required length) 34325.1001 - Tube, Silicone .38" ID x 36.0" (Cut to required length) 34325.1002 - Tube, Silicone .38" ID x 120.0" (Cut to required length) 11M2337.1000-Tube Insulation (Cut to required length)CIRCULATION PUMP & LINES38311 1117062038311 111706ITEMPART NO.QTY.DESCRIPTION21* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.PRODUCT COIL & LINES1 - - - - - - - - 1 Product Coil (See WATER TANK ASSEMBLY)2 35305.0000 2 Gasket3 35173.0001 1 Fitting .312" Fl x .375" Barb4 21275.0003 8 Clamp .57" - .70"5 34325.0010* 1 Hose, Flex .38" ID x 17.0" (Order item 19)(Early models prior to Water Inlet Valve) 34325.0014* 1 Hose, Flex .38" ID x 15.0" (Order item 19)(Late models with Water Inlet Valve)6 33151.0004 1 Fitting, Elbow .38" Barb7 33149.0000 1 Gasket8 12757.0000 1 Nut9 01514.0000 1 Lockwasher 10 12756.0000 1 Fitting, Bulkhead11 35172.0001 1 Fitting, Elbow .312" Fl x .375" Barb 12 34325.0004* 1 Hose, Flex .38" ID x 1.5" (Order item 19) 13 37850.0000 1 Elbow .38" Barb14 34325.0012* 1 Hose, Flex .38" ID x 10.5" (Order item 19) 15 35171.0000 1 Valve, Shut Off 16 34540.0000 1 Decal, Caution - Close17 34325.0004* 1 Hose, Flex .38" ID x 1.5" (Order item 19) 18 34462.0000 1 Coupling, Quick Disconnect, Male19 34325.1000 1 Hose, Flex .38" ID x 12.0" (Cut to required length) 34325.1001 1 Hose, Flex .38" ID x 36.0" (Cut to required length) 34325.1002 1 Hose, Flex .38" ID x 120.0" (Cut to required length)20M2337.1000-Insulation, Tube 25/50 - 0.5"ID x .19" wall x 6.0 Ft (Use as required)38311 111706Early Models2238311 110107ITEMPART NO.QTY.DESCRIPTION23* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.DISPENSE PLATFORM ASSEMBLY1 38116.1000 1 Platform Assy (Includes items2 - 18) 2 - - - - - - - - 2 Pump Assy (See PUMP ASSY) 01338.0000 2 Screw, Truss Head #8-32 x .625" 01522.0000 4 Washer00991.0000 4 Nut, Elastic Lock #8-32 3 32957.0001 8 Bushing, Rubber 4 21275.0006 4 Clamp .40" - .50"5 38018.1000 2 Dispense Valve (See DISPENSE VALVE) 01308.0000 4 Screw, Truss Head #6-32 x 25"6 37786.0001 2 Plate 01308.0000 2Screw, Truss Head #6-32 x 25"7 - - - - - - - - 1 Manifold, Plain Water (See PLAIN WATER MANIFOLD) 8 - - - - - - - - 1 Manifold, Rinse Water (See RINSE WATER MANIFOLD) 9 32756.1000 2 Bottle Adapter (See BOTTLE ADAPTER) 01308.0000 4 Screw, Truss Head #6-32 x 25" 10 38122.0000* 1 Plate 01311.0001 4Screw, Truss Head #8-32 x .25" Lkg.11 32458.0000 2 Clip, Retainer 12 38104.0000 2 Thumbscrew 13 32454.0000 2 Fitting 1434087.00002O-ringThe following items are not illustrated 15 35189.0000 1 Harness, Dispense Platform 16 35181.0001 1 Harness, Dispense Valve 17 - - - - - - - - 4 Cable Tie (Not serviced) 1812422.00002Clamp38311 1101072438311 062905ITEMPART NO.QTY.DESCRIPTION25* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.DISPENSE VALVE ASSEMBLY- 38018.1000 1 Dispense Valve Assy (Includes items 1 - 24) 1 37801.0001 1 Body 2 37990.0000 1 Seal 3 37843.0000 1 Nozzle, Water4 32252.0000 1 Valve, Solenoid (Includes items5 - 10) 5 33554.0000 1 Solenoid Valve Coil6 28481.0000 1 Guide Kit (Includes Guide, Washer and O-ring)7 33585.0000 1 Solenoid Valve Base Kit (Includes O-ring and items 6 & 7) 8 01111.0002 1 Solenoid Valve Repair Kit (Includes Plunger, Spring and O-ring) 9 33580.0000 1 O-ring 10 33553.0000 1 O-ring11 37987.0000 1 Bracket 01308.0000 2 Screw #6-32 x .25" 12 32463.0000 1 Fitting, Elbow13 32849.0001 1 O-ring (Also use item 24) 14 37853.0000 1 Clamp 01308.0000 1 Screw #6-32 x .25" 15 32603.0000 1 Sleeve16 32852.0000 1 O-ring (Also use item 24) 17 32602.0000 1 Piston18 32853.0001 1 Spring, Flow Control 19 32624.0000 1 Bonnet, Adjuster 20 33725.0000 1 O-ring (Also use item 24) 21 32623.0000 1 Adjuster, Position 22 32851.0000 1 O-ring (Also use item 24) 23 37977.0000 1 Bracket, Water Adjustment 01308.0000 2 Screw #6-32 x .25"24M2568.1000-Grease, USDA H-1 (Use when assembling items 13,16,20 & 22)38311 1117062638311 111706ITEMPART NO.QTY.DESCRIPTION27* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.PLAIN WATER MANIFOLD (Early Models)1 32631.00002 Fitting, Straight 2 32849.0001 2 O-ring3 38129.0005* 2 Hose, Braided .25" ID x 2.25" (Order item 12)4 21275.0006 4 Clamp .40 - .50"5 36204.0000* 1 Manifold, Plain SST6 34325.0017* 1 Hose, Flex .38" ID x 1.25" (Order item 13)7 21275.0003 2 Clamp .57 - .70"8 34463.0000 1 Coupling, Quick Disconnect, Female12 38129.1000 1 Hose, Braided .25" ID x 12.0" (Cut to required length) 38129.1001 1 Hose, Braided .25" ID x 36.0" (Cut to required length) 38129.1002 1 Hose, Braided .25" ID x 120.0" (Cut to required length) 13 34325.1000 1 Hose, Flex .38" ID x 12.0" (Cut to required length) 34325.1001 1 Hose, Flex .38" ID x 36.0" (Cut to required length)34325.10021Hose, Flex .38" ID x 120.0" (Cut to required length)38311 1117062838311 111706ITEMPART NO.QTY.DESCRIPTION29* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.PLAIN WATER MANIFOLD (Late Models)38311 1117061 32631.00002 Fitting, Straight 2 32849.0001 2 O-ring3 38129.0012* 2 Hose, Braided .25" ID x 3.0" (Order item 8)4 21275.0006 6 Clamp .40 - .50"5 38605.0000 1 Tee .25" Barb6 38129.0013* 1 Hose, Braided .25" ID x 5.25" (Order item 8)7 34461.0000 1 Coupling, Quick Disconnect, Female8 38129.1000 1 Hose, Braided .25" ID x 12.0" (Cut to required length) 38129.1001 1 Hose, Braided .25" ID x 36.0" (Cut to required length)38129.10021Hose, Braided .25" ID x 120.0" (Cut to required length)3038311 111706RINSE WATER MANIFOLD & SOLENOID (Early Models) ITEM PART NO. QTY. DESCRIPTION1 32756.10002 Bottle adapter (See BOTTLE ADAPTER)2 38129.0001*3 Hose, Braided .25" ID x .44" OD x 1.50" (Order item 37)3 21275.0006 16 Clamp .40" - .50"4 36203.0000* 1 Manifold. Rinse SST5 34460.0000 1 Fitting, Quick Disconnect, Male6 34461.0000 1 Fitting, Quick Disconnect, Female7 32745.0021* 1 Hose .25" ID x .44" OD x 15.75" (Order item 38)8 33151.0005 3 Fitting, Elbow .25" Barb9 33149.0001 4 Gasket10 01085.0002 1 Solenoid Valve 120V (Includes items 11 - 14)28005.0000 1 Solenoid Valve 230V (Includes items 11- 13)01327.0000 2 Screw, Pan Head #10-32 x .38" 120V02308.0000 2 Screw, Pan Head #8-32 x .38" 230V11 28480.0000 1 Coil, Solenoid 120V28020.0000 1 Coil, Solenoid 230V12 01111.0002 1 Solenoid Repair Kit (Includes Plunger, Spring and O-ring)13 28479.0000 1 Solenoid Base Kit 120V (Includes O-ring)28021.0000 1 Core Assy Kit 230V14 28481.0000 1 Guide Kit15 00402.0001 2 Connector16 00425.0001 1 Nipple17 00425.0002 1 Nut18 38129.0001* 1 Hose, Braided .25" ID x .44" OD x 1.50" (Order item 37)19 00459.0000 1 Fitting, Bulkhead01532.0000 1 Lockwasher, Internal-toth .438"00463.0000 1 Nut, Hex .375"-2020 38129.0009* 1 Hose, Braided .25" ID x .44" OD x 4.25" (Order item 37)21 33149.0000 3 Gasket22 33151.0004 1 Fitting, Elbow .38" Barb23 21275.0003 4 Clamp .57" - .70"24 34325.0004* 1 Hose, Flex .38" ID x .595" OD x 1.5" (Order item 39)25 32749.0001 1 Tee .38" Barb x .38" Barb x .25" Barb(Continued)RINSE WATER MANIFOLD & SOLENOID (Early Models) ITEM PART NO. QTY. DESCRIPTION26 34325.0006* 1 Hose, Flex .38" ID x .595" OD x 2.25" (Order item 39)27 33150.0000 1 Nut28 33686.0000 1 Nipple29 23720.0000 1 Strainer Assy (Includes items 30 - 32)30 - - - - - - - - 1 Housing, Strainer (Order item 29)31 23721.0000 1 Screen32 23723.0000 1 End Cap33 21275.0006 2 Clamp .41 - .50"34 35573.0000* 1 Bracket, Rinse Solenoid (Early Models)01317.0003 2 Screw, Truss Head #8-32 x .38" Lkg35 32463.0000 2 Fitting, Elbow36 32849.0001 2 O-ring37 38129.1000 - Hose, Braided .25" ID x .44" OD x 12.0" (Cut to required length)38129.1001 - Hose, Braided .25" ID x .44" OD x 36.0" (Cut to required length)38129.1002 - Hose, Braided .25" ID x .44" OD x 120.0" (Cut to required length)38 32745.1002 - Hose .25" ID x .44" OD x 120.0" (Cut to required length)39 34325.1000 - Hose, Flex .38" ID x .595" OD x 12.0" (Cut to required length)34325.1001 - Hose, Flex .38" ID x .595" OD x 36.0" (Cut to required length)34325.1002 - Hose, Flex .38" ID x .595" OD x 120.0" (Cut to required length)ITEMPART NO.QTY.DESCRIPTIONRINSE WATER MANIFOLD & SOLENOID (Late Models)(Continued)1 32756.10002 Bottle adapter (See BOTTLE ADAPTER) 2 32849.0001 2 O-ring3 32463.0000 2 Fitting, Elbow4 38129.0009* 1 Hose, Braided .25" ID x 4.25" (Order item 40)5 21275.0006 8 Clamp .40" - .50"6 38129.0004* 1 Hose, Braided .25" ID x 3.50" (Order item 40)7 38605.0000 1 Tee .25" Barb8 38129.0001* 1 Hose, Braided .25" ID x 1.50" (Order item 40) 9 34460.0000 1 Fitting, Quick Disconnect, Male 10 34461.0000 1 Fitting, Quick Disconnect, Female11 32745.0021* 1 Hose .25" ID x 15.75" (Order item 39)(Early models prior to Water Inlet Valve) 38129.0014* 1 Hose .25" ID x 13.0" (Order item 40)(Late models with Water Inlet Valve) 12 01085.0002 1 Solenoid Valve 120V (Includes items 13 - 16) 28005.0000 1 Solenoid Valve 230V (Includes items 13- 15) 01327.0000 2 Screw, Pan Head #10-32 x .38" 120V02308.0000 2 Screw, Pan Head #8-32 x .38" 230V 1328480.0000 1 Coil, Solenoid 120V 28020.0000 1 Coil, Solenoid 230V14 01111.0002 1 Solenoid Repair Kit (Includes Plunger, Spring and O-ring) 15 28479.0000 1 Solenoid Base Kit 120V (Includes O-ring) 28021.0000 1 Core Assy Kit 230V 16 28481.0000 1 Guide Kit17 35573.0000* 1 Bracket, Rinse Solenoid (Early Models) 01317.0003 2 Screw, Truss Head #8-32 x .38" Lkg 18 00402.0001 1 Connector19 33151.0005 1 Fitting, Elbow .25" Barb 20 33149.0001 1 Gasket21 33152.0001 1 Fitting .38" Barb x .125" MPT22 34325.0022* 1 Hose, Flex .38" ID x 2.50" (Order item 41) 23 32750.0001 1 Tee .38" Single Barb24 34325.0021* 1 Hose, Flex .38" ID x 8.0" (Order item 41) 25 33686.0000 1 Nipple33150.00001NutRINSE WATER MANIFOLD & SOLENOID (Late Models) ITEM PART NO. QTY. DESCRIPTION26 21275.0003 5 Clamp .57" - .70"27 36203.0000* 1 Manifold. Rinse SST (Early Models)28 33149.0000 2 Gasket29 23720.0000 1 Strainer Assy (Includes items 30 - 32)30 - - - - - - - - 1 Housing, Strainer (Order item 29)31 23721.0000 1 Screen32 23723.0000 1 End Cap33 01533.0005 2 Spacer01326.0006 2 Screw, Truss Head #10-32 x .625"34 00464.0001 1 Elbow .25" Barb x .125"MPT35 34325.0004* 2 Hose, Flex .38" ID x 1.50" (Order item 41)36 35077.0000 1 Tee, Nylon .38" Barb37 36233.0000 1 Valve, Water Inlet 120V36233.0001 1 Valve, Water Inlet 230V32283.0000 2 Screw, Pan Head M4 x 6mm38 37297.0000 1 Elbow39 32745.1002 - Hose .25" ID x .44" OD x 120.0" (Cut to required length)40 38129.1000 - Hose, Braided .25" ID x .44" OD x 12.0" (Cut to required length)38129.1001 - Hose, Braided .25" ID x .44" OD x 36.0" (Cut to required length)38129.1002 - Hose, Braided .25" ID x .44" OD x 120.0" (Cut to required length) 41 34325.1000 - Hose, Flex .38" ID x .595" OD x 12.0" (Cut to required length)34325.1001 - Hose, Flex .38" ID x .595" OD x 36.0" (Cut to required length)34325.1002 - Hose, Flex .38" ID x .595" OD x 120.0" (Cut to required length)PUMP ASSEMBLYITEM PART NO. QTY. DESCRIPTION- 33803.1001 1 Pump Assy (Includes items 1 - 29)1 32613.1002 1 Motor Assy01322.0001 4 Screw #8-32 x 1.25"2 32654.0000 1 Magnet Hub01512.0000 1 Lockwasher, Internal-tooth #1001331.0004 1 Screw, Locking #10-32 x .50"3 33608.1000 1 Sensor, RPM02336.0000 2 Screw #4-40 x .38"4 07130.0000* 1 Cable Tie5 32957.0000 4 Bushing6 37152.0001 1 Mount Assy, Pump7 29904.0000 1 Insert, Well Nut #8-328 33781.0000 1 Gasket9 28755.0010* 1 Tube, Norprene .25" ID x 18.5" lg (Order item 17)10 32732.0000 1 Clamp .39"/.48"11 32656.0000 1 Fitting, Elbow .25" Barb x .38" Barb12 21275.0003 1 Clamp .57"/.70"13 34325.0019* 1 Hose, Flex .375" ID x 5.75" lg (Order item 18)14 28759.0000 1 Pump Assy. (Includes items 15 & 16)15 28794.0000 1 Rotor16 01370.0001 4 Screw, Pan Head #8-32 x 2.45"17 28755.1000 - Tube, Neoprene .25" ID x .45" OD x 12.0" (Use as required)28755.1001 - Tube, Neoprene .25" ID x .45" OD x 36.0" (Use as required)28755.1002 - Tube, Neoprene .25" ID x .45" OD x 60.0" (Use as required) 18 34325.1000 - Hose, Flex .375" ID x 12.0" (Use as required)34325.1001 - Hose, Flex .375" ID x 36.0" (Use as required)34325.1002 - Hose, Flex .375" ID x 120.0" (Use as required)19 39689.0000 - Pump Tube (Includes items 9,10,11,12 & 13)。

SU 1699B - PV DC Arc-Fault Circuit Protection AFCI
• Scope Includes: – Requirements cover DC photovoltaic arc-fault circuit protection devices for use in PV systems as described in Article 690 of the NEC. – Protection is intended to mitigate the effects of arcing faults that may pose a risk of fire. – Covers PV dc arc-fault circuit-interrupters (AFCI), arcfault detectors (AFD), interrupting devices (ID) and – inverters, converters, and charge controllers with integral arc-fault circuit interrupter protection. – Rated up to 1000V dc. – Includes optional parallel tests but not required by 690.11
Subject 1699B Tests
Humidity Leakage Voltage surge Environmental sequence Arc fault detection Unwanted tripping Inhibition Temperature Overvoltage Overload Endurance Dielectric Withstand Abnormal Short circuit Corrosion Test Crushing Strain relief Mechanical Resistance to Environmental Noise Electrostatic discharge Radiated EMI Fast transients Voltage surge Induced RF fields Voltage dips Surge current Abnormal overvoltage

PCI-EXPRESS CLOCK SOURCEDescriptionThe ICS557-01 is a clock chip designed for use inPCI-Express Cards as a clock source. It provides a pair of differential outputs at 100 MHz in a small 8-pin SOIC package.Using IDT’s patented Phase-Locked Loop (PLL) techniques, the device takes a 25 MHz crystal input and produces HCSL (Host Clock Signal Level) differential outputs at 100 MHz clock frequency. LVDS signal levels can also be supported via an alternative termination scheme.Features•Supports PCI-Express TM HCSL Outputs0.7 V current mode differential pair •Supports LVDS Output Levels•Packaged in 8-pin SOIC•RoHS 5 (green ) or RoHS 6 (green and lead free) compliant packaging•Operating voltage of 3.3 V•Low power consumption•Input frequency of 25 MHz•Short term jitter 100 ps (peak-to-peak)•Output Enable via pin selection•Industrial temperature range availableBlock DiagramPin Assignment Pin DescriptionsPin NumberPinNamePinTypePin Description1OE Input Output Enable signal(H = outputs are enabled, L = outputs are disabled/tristated).Internal pull-up resistor.2X1Input Crystal or clock input. Connect to a 25 MHz crystal or single ended clock. 3X2XO Crystal Connection. Connect to a parallel mode crystal.Leave floating if clock input.4GND Power Connect to ground.5IREF Output A 475Ω precision resistor connected between this pin and groundestablishes the external reference current.6CLK Output HCSL differential complementary clock output.7CLK Output HCSL differential clock output.8VDD Power Connect to +3.3 V.Applications Information External ComponentsA minimum number of external components are required for proper operation.Decoupling CapacitorsDecoupling capacitors of 0.01 μF should be connected between VDD and the ground plane (pin 4) as close to the VDD pin as possible. Do not share ground vias between components. Route power from power source through the capacitor pad and then into IDT pin.CrystalA 25 MHz fundamental mode parallel resonant crystal with C L = 16 pF should be used. This crystal must have less than 300 ppm of error across temperature in order for theICS557-01 to meet PCI Express specifications.Crystal CapacitorsCrystal capacitors are connected from pins X1 to ground and X2 to ground to optimize the accuracy of the output frequency.C L= Crystal’s load capacitance in pFCrystal Capacitors (pF) = (C L- 8) * 2For example, for a crystal with a 16 pF load cap, each external crystal cap would be 16 pF. (16-8)*2=16.Current Source (Iref) Reference Resistor - R RIf board target trace impedance (Z) is 50Ω, then R R = 475Ω(1%), providing IREF of 2.32 mA. The output current (I OH) is equal to 6*IREF.Output TerminationThe PCI-Express differential clock outputs of the ICS557-01 are open source drivers and require an external series resistor and a resistor to ground. These resistor values and their allowable locations are shown in detail in thePCI-Express Layout Guidelines section.The ICS557-01can also be configured for LVDS compatible voltage levels. See the LVDS Compatible Layout Guidelines sectionGeneral PCB Layout RecommendationsFor optimum device performance and lowest output phase noise, the following guidelines should be observed.1. Each 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible.2. No vias should be used between decoupling capacitor and VDD pin.3. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. Distance of the ferrite bead and bulk decoupling from the device is less critical.4. An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers (any ferrite beads and bulk decoupling capacitors can be mounted on the back). Other signal traces should be routed away from the ICS557-01.This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device.PCI-Express Layout GuidelinesFigure 1: PCI-Express Device RoutingTypical PCI-Express (HCSL) WaveformLVDS Compatible Layout GuidelinesFigure: LVDS Device RoutingTypical LVDS WaveformAbsolute Maximum RatingsStresses above the ratings listed below can cause permanent damage to the ICS557-01. These ratings are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range.DC Electrical CharacteristicsUnless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85°C1 Single edge is monotonic when transitioning through region.2 Inputs with pull-ups/-downs are not included.ItemRatingSupply Voltage, VDD, VDDA 5.5 VAll Inputs and Outputs-0.5 V to VDD+0.5 V Ambient Operating Temperature (commercial)0 to +70°C Ambient Operating Temperature (industrial)-40 to +85°C Storage Temperature -65 to +150°C Junction Temperature 125°C Soldering Temperature 260°CESD Protection (Input)2000 V min. (HBM)ParameterSymbolConditions Min.Typ.Max.UnitsSupply Voltage V 3.135 3.465Input High Voltage 1V IH 2.0VDD +0.3V Input Low Voltage 1V IL VSS-0.30.8V Input Leakage Current 2I IL 0 < Vin < VDD-55μA Operating Supply Current I DD With 50Ω and 2 pF load 55mA I DDOE OE =Low35mA Input Capacitance C IN Input pin capacitance 7pF Output Capacitance C OUT Output pin capacitance 6pF Pin Inductance L PIN 5nH Output Resistance Rout CLK outputs 3.0k ΩPull-up ResistorR PUPOE60k ΩAC Electrical Characteristics - CLK/CLKUnless stated otherwise, VDD=3.3 V ±5%, Ambient Temperature -40 to +85°C1 Test setup is R L =50 ohms with2 pF , R R = 475Ω (1%).2 Measurement taken from a single-ended waveform.3 Measurement taken from a differential waveform.4Measured at the crossing point where instantaneous voltages of both CLKOUT and CLKOUT are equal.5 CLKOUT pins are tri-stated when OE is low asserted. CLKOUT is driven differential when OE is high.Thermal Characteristics (8-pin SOIC)ParameterSymbolConditions Min.Typ.Max.UnitsInput Frequency 25MHz Output Frequency 100MHzOutput High Voltage 1,2V OH 660700850mV Output Low Voltage 1,2V OL-150027mV Crossing Point Voltage 1,2Absolute250350550mV Crossing Point Voltage 1,2,4Variation over all edges140mV Jitter, Cycle-to-Cycle 1,380ps Rise Time 1,2t OR From 0.175 V to 0.525 V 175332700ps Fall Time 1,2t OFFrom 0.525 V to 0.175 V175344700ps Rise/Fall Time Variation 1,2125ps Duty Cycle 1,34555%Output Enable Time 5All outputs 30µs Output Disable Time 5All outputs30µs Stabilization Time t STABLEFrom power-up VDD=3.3 V3.0ms Spread Change Timet SPREAD Settling period after spread change3.0msParameterSymbolConditionsMin.Typ.Max.UnitsThermal Resistance Junction to AmbientθJA Still air150°C/W θJA 1 m/s air flow 140°C/W θJA 3 m/s air flow120°C/W Thermal Resistance Junction to CaseθJC40°C/WMarking Diagram (ICS557M-01LF) Marking Diagram (ICS557MI-01LF)Notes:1. ###### is the lot code.2. YYWW is the last two digits of the year, and the week number that the part was assembled.3. “L ” designates Pb (lead) free packaging.4. “I” denotes industrial temperature.5. Bottom marking: (orgin). Origin = country of origin if not USA.Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95Ordering InformationPart / Order Number Marking Shipping Packaging Package Temperature 557M-01LF See Page 8Tubes8-pin SOIC0 to +70° C557M-01LFT Tape and Reel8-pin SOIC0 to +70° C557MI-01LF Tubes8-pin SOIC-40 to +85° C557MI-01LFT Tape and Reel8-pin SOIC-40 to +85° C"LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.Corporate HeadquartersIntegrated Device Technology, For Sales800-345-7015408-284-8200Fax: 408-284-2775For Tech Support/go/clockhelpInnovate with IDT and accelerate your future networks. Contact:www.IDT .com。