模具专业英语词汇收集

模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。

50个模具专业术语1. 模具 (Mold)2. 塑料模具 (Plastic Mold)3. 金属模具 (Metal Mold)4. 注塑机 (Injection Molding Machine)5. 压铸机 (Die Casting Machine)6. 打磨 (Polishing)7. 铣削 (Milling)8. 钳工 (Machining)9. 精雕 (Engraving)10. 焊接 (Welding)11. 冲压 (Stamping)12. 切割 (Cutting)13. 合模 (Closing)14. 分模 (Opening)15. 导柱 (Guide Pillar)16. 导套 (Guide Bush)17. 滑块 (Slider)18. 塑料件 (Plastic Part)19. 金属件 (Metal Part)20. 模仁 (Core)21. 模腔 (Cavity)22. 底座 (Base)23. 热流道 (Hot Runner)24. 冷却系统 (Cooling System)25. 泵箱 (Pump Box)26. 压缩机 (Compressor)27. 水力缸 (Hydraulic Cylinder)28. 模具钢 (Mold Steel)29. 法兰 (Flange)30. 注塑模具 (Injection Mold)31. 放电加工 (Electrical Discharge Machining)32. 模仁巧妙 (Core Pull)33. 螺旋通道 (Spiral Channel)34. 冷却塔 (Cooling Tower)35. 酸洗 (Acid Etching)36. 布胶 (Rubberizing)37. 文字标记 (Texturing)38. 研磨剂 (Polishing Compound)39. 硅胶 (Silicone)40. 硬度测试 (Hardness Testing)41. 射出速度 (Injection Speed)42. 模具寿命 (Mold Life)43. 热流道系统 (Hot Runner System)44. 冷却时间 (Cooling Time)45. 模具设计 (Mold Design)46. 模具制造 (Mold Manufacturing)47. 模具修理 (Mold Repair)48. 模具改造 (Mold Modification)49. 模具试模 (Mold Trial)50. 模具测试 (Mold Testing)。

模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。

模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。

模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin 开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft 滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plate A板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板11 / 17Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。

Injection Mold Technical Terms(一)模具专业基本用词Professional Terms1.塑料—plastic, resin2.样件—sample3.钢料—steel4.注塑机—injection machine, press5.产品—part, product, moulding6.模具—mold, mould, toolA 简易模(样板模)—prototype moldB 量产用模具—production mold7.三维造型(数模)—3D model, 3D data8.二维产品图—2D part drawing9.设计—design10.制造—manufacture, build up, construction11.检验—check, inspection12.测量—measure, inspection13.修改—change, modify, correction14.工程更改—engineer change15.质量—quality16.数量—quantity17.基准—datum, reference牛角入水-rads gate(二)如何解析2D 产品图?How to read 2D part drawing?一.产品几何Geometry1.点—point2.线(边)—line, edge3.面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface4.壁厚—wall thickness, stock thickness5.加强筋(骨位)—rib6.孔—hole7.细长的槽—slot8.柱位—boss9.角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner10.斜度—angle, taper11. 凹槽—recess , groove第 1 页共11 页二.分模信息Splitting1.分型线—parting line (P/L), splitting line2.主分模方向—main direction, line of draw3.浇口设定—gating产品标识Part Identification1.产品名称—part name (P/N)2.产品编号+版本号—part number + revision (Rev.)3.型腔号—cavity number4.材料标记—material symbol5.模具编号—mold number (no.)6.日期印—dating insert, date code7.循环印—cycling code8.公司标志—company logo三.技术要求Specification (Special Requirement)1.项目启动表Kick-off sheet1)项目名称—program name, project name2)产品名称—part name, product name, part description3)产品编号—part number (P/N)4)客户模号—customer mold no.5)项目启动日期—kick off date, start date6)项目完成日期—due date,lead time7)内模件用钢—tool steel8)型腔数量—number of cavities9)数据文件编号—data file no.10)注塑材料—resin, plastic, raw material11)收缩率—shrink, shrinkage, shrink factor12)注塑机吨位—molding machine size, injection machine size13)成型周期—cycle time14)型腔光洁度—cavity polish15)型芯光洁度—core polish16)皮纹(晒纹)—texture, grain17)拔模斜度—draft angle, removal taper18)注塑件颜色及光泽—molded color & gloss19)模具加工地—manufacturing facility20)热流道供应商—manifold manufacturer, manifold supplier21)浇口位置—gate location / position22)浇口类型—gate type23)产品标识—stamp information, part identification24)特殊要求—special instructions25)安全模数—safe steel2.产品质量及外观要求Part Quality & Appearance Requirement1)尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受(合格)—accept, OK⑧拒绝(不合格)—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2)产品缺陷(常见的)Defects (normal)①缩水—sink mark, shrinkage②飞边,毛边—flash, burr③段差—mismatch discrepancy④银丝纹,蛇纹—snake marks, streak⑤弯曲,变形—warpage, distortion⑥打不饱(缺料)—short shot⑦熔接线—weld line⑧多胶—unwanted plastic⑨拉伤—damage3.产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4.常用词汇、词组及短语Normal Word, Short Sentence1)单边—per side2)双边—both sides3)加入,添加—add, incorporate4)去除,取消—remove, cancel5)满足…的要求,符合,与…要求一致—according to, conform to, satisfy, meet6)要求,需要—require, need, demand7)确认—be approved, agreed by …8)允许—permit, allow9)在…范围之内—within10)不可以,不允许,禁止—free from, prevent, avoid11)…,除非有另指—…unless otherwise specified12)…或少于—…or less13)自动化运作—automatic operation14)未注尺寸(详细形状)见三维造型Non dimensioned contour (detailed shape) see 3D model. 15)分型线上的飞边(披缝)或段差应小于…Burrs or discrepancy on the P/L shall be … or less.四.标题栏Title Block1.产品名称—part name2.图纸编号 + 版本号(索引号)—drawing no. + level (index)3.一般公差—general tolerance(三)如何阅读制模标准?How to read tooling standard?一.模具结构术语Mold Construction TermsA.模架Mold Base1.模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸(模厚)—stack height of mould③模具重量—total weight of mould, mould thickness2.定模底板—front plate, top clamping plate, clamp plate, clamping plate3.定模板—cavity plate, fixed mould plate, A – plate4.动模板—core plate, moving mould plate, B – plate5.浮动板—floating plate6.支撑板—support plate, backing plate7.间隔板,方铁—support blocks, rails, risers, spacer block8.顶杆固定板—retaining plate, ejector retaining plate9.顶板—ejector plate,bottom clamping plate10.动模底板—back plate11.导柱—guide pillar, leader pin, guide pin12.导套—guide bush, leader pin bush13.复位杆—return pin, push-back pin14.弹簧—spring15.撑头—support pillar16.顶针板导柱、导套—ejection guide pin / bush17.垃圾钉—stop pin, stop button18.模脚—standing-off pillars19.标牌—plaque scutcheonB.成型零部件moulding components20.型芯—core insert21.型腔—cavity insert22.镶针—core pin23.镶块—sub-insert, split24.滑块—slide, sliding split25.斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib26.成型顶杆—moulding face pin, form pinC.浇注系统Feed System1.塑料Plastica.主流道—sprueb.分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc.浇口gate常用浇口形式normal gate type :①边缘浇口(J型浇口)—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated.模腔—impressione.冷料井—cold slug wellf.热流道—hot runner2.模具零件mold componentsa.定位圈—locating ring, location ring, register ringb.浇口套—sprue bushc.挡圈—stop ringd.浇口镶块—gate inserte.热流道板—manifoldf.热嘴—hot dropD.分型面及其锁紧、排气Parting Surface, inter-locking & venting1.分型线—parting line ( P/L )2.镶拼线—bodyline, joint line3.平/ 不平的分型面—flat / non – flat parting surface4.封胶面—shut off surfaces, seal-off surfaces5.擦穿位—shut off6.碰穿位—kiss-off7.管位—parting line lock8.分型面的释放(避空) —relief of parting surface9.分型面的平衡—balancing of parting surface10.锁紧角度—locking angle11.锁紧力—clamping force12.锁模块—safety strap13.精定位—Interlock, die lock14.困气—air trap15.排气槽—vent, vent slot16.撬模坑--- pry slot17.计数器--- shot counter/ cycle counterE.滑块机构Slide1.驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2.制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3.导轨—gib, guide strip,center guide4.锁紧块(楔紧块)—heel block, locking heel, wedge block, chase block,slide driver5.耐磨片—wear plate, wear strip6.压板—retainer,gib7.螺钉—screw8.定位销—dowel pin9.行位扣—slide lock / slide retainer10. flat ejector pin 扁顶针F.斜顶机构Lifter1.斜顶头—lifter head2.斜顶杆—lifter rod, lifter shaft3.斜顶固定块—lifter rod retainer4.斜顶导向块—lifter guide5.开口销—split pin6.固定板(压板)—retainer plate7.耐磨片—wear plate8.铜导套—bronze bushing9.导套固定板—bushing retainer10.衬套—spacer11.导轨—L – gib12.导轨---T-Gib13.滑动块—slide14.连接块—U-CouplingG.顶出系统Ejection System1.基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick on④产品脱模—part is push off from, clear part of mould, separation of part2.顶板机构Ejector plate assembly①顶板—ejector plate②顶板固定板—retaining plate③推板—stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头—support pillar⑦限位块—stop block,stroke block3.复位机构Return System①复位杆(回程杆)—return pin, push – back pin②垃圾钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构—early return system⑥强制复位机构—positive return system4.顶出方法Ejection Techniques1)顶杆顶出—pin ejection2)顶管顶出—sleeve ejection3)顶块顶出—bar ejection4)扁顶顶出—blade ejection5)顶板顶出—stripper ejection6)油缸顶出—hydraulic ejection7)气顶—air ejection8)阀门顶出—valve ejection5.顶出元件Ejection Elements1)拉料杆—sprue puller, sucker pin2)顶杆—ejector pin3)阶梯式顶杆—stepped ejector pin4)顶管—ejection sleeve, sleeve5)扁顶—ejector blade, slabbed off ejector pin6)顶块—stripper bar7)顶环—stripper ring8)推板—stripper plate9)加速顶—accelerated ejection10)直顶----straight lifter/EJECTOR BAR6.顶出辅助机构Supplementary operating system1)弹簧柱塞器—spring – loaded plunger2)弹珠定位器—ball catch system3)插销式锁扣—Latch – lock4)尼龙拉杆装置—friction puller device7.电器元件Electric Components1)压力传感器—pressure transducer2)限位开关—limit switchF.冷却系统Cooling System1.基本词汇Basic Word1)温差—temperature variation2)水孔(水道)—waterlines, water-ways, flow-way, channel3)水路—cooling circuit4)水路示意图—water schematic, schematic circuit5)冷却液—coolant, coolant fluid6)内连接—interconnect7)外连接—external connection8)出口、入口—outlet、inlet9)漏水—water leakage2.水路分布Circuits1)阶梯式水路—stepped system2)分隔板水路—baffled hole system3)斜孔式水路—angled hole system3.水路元件Components1)闷头(螺塞、止水栓)—(threadless)brass pressure plug : female plug & male2)隔水片—baffle3)密封圈—O – ring4)快插水路接头—quick disconnect fitting, quick connection adaptor5)弯头—elbow6)偶合器(连接器、接头)—adaptor (including a plug & a socket)7)橡皮管—rubber hose8)分水板,集水块—water manifoldG.螺纹、螺纹孔& 螺钉Thread, thread hole & screw1.螺纹—thread2.管螺纹—pipe thread3.螺纹孔—screw hole, tapped hole4.起吊孔—handling hole, jack screw hole, eye bolt hole5.螺钉—screw6.内六角螺钉—socket headed cap screw (s.h.c.s.)7.沉头螺钉—flat headed cap screw (f.h.c.s)8.螺栓—bolt9.螺母—nut10.锁紧螺母—locknut11.螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread (BSP)④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread (UNC)⑥美制细螺纹标准—United Fine thread (UNF)H.润滑Lubrication1.润滑槽—grease groove2.加油管—grease line3.油杯—lubrication fittingI.测量仪器Measuring Instruments1.游标卡尺—vernier caliper2.千分尺—micrometer3.高度规—height gauge4.刻度规—dial gauge5.三坐标测量仪(三次元)—Coordinate Measure Machine(CMM)6.塞规—pin gauge7.圆角量规—radii gauge8.轮廓投影机—profile projectorJ.注塑机参数Injection Machine Parameter1.注塑机规格参数Injection Machine Specification①锁紧类型clamp typea.油缸—hydraulicb.肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2.试模工艺参数Moulding Process Parameter, machine setting①时间Timer(TM), seca.注塑(充填)时间—filling time, injection timeb.冷却时间—cooling timec.补缩时间—packing timed.保压时间—holding timee.成型周期—cycle time②速率、速度Velocity, %、speed, in/seca.注塑(充填)速度—injection speedb.保压速率—hold pressure velocityc.螺杆转速—screw rotation speed③压力Pressure(Prs.), psia.注塑压力—injection pressureb.保压压力—hold pressurec.回压(背压)—back pressure④温度Temperature(Temp.), °Fa.注塑机喷嘴温度—nozzle temp.b.料筒前段、中段、后段温度—barrel front、middle、rear temp.c.模温—mould temp.d.料温—purged resin melt temp.e.空射料温—air shot melt temp. 第11 页共11 页。

Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。

模具专业英语词汇Aabrasion n. 磨损abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 Bback pressure 背压 bismutbaffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套barrel temperature 料筒温度 blush 发blank through dies 漏件式落料模 burnishblow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺buttonby-product n. 副产品 Ccalendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造catalyst n. 催化剂cavity n. 型腔chemical resistance n. 耐化学腐蚀性chip v. 削 /凿clamping force n. 锁模力clamping tonnage n. 锁模吨位coil spring弹簧computer aided design (CAD) n. 电脑辅助设计computer aided manufacture (CAM) n. 电脑辅助制造cover plate盖板computer numerical control (CNC) n. 电脑数字控制ceramic n. 陶瓷calendaring molding 压延成形cavity 型控母模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模chill mold 冷硬用铸模cold chamber die casting 冷式压铸cold forging 冷锻cold slag 冷料渣cold slug 冷斑cold rolled steel n. 冷轧圆钢cold runner n. 冷流道colorant n. 着色剂compacting molding 粉末压出成形composite n. 复合材料composite dies 复合模具compound molding 复合成形compression molding 压缩成形compression strength n. 抗压强度cooling channel/circuit n. 冷却管道cooling rate n. 冷却速率core n. 型芯 /模芯corrosion n. 腐蚀corrosion resistance n. 耐腐蚀性counter punch 反凸模cure v. 固化custom adj. 定制cycle time n. 循环时间Ddegassing n. 排气density n. 密度deform v. 变形delamination 起皮diaphragm gate 隔膜浇口die n. 冲模die casting n. 压铸 /模铸deburring punch压毛边冲子die holder下夹板die pad下垫板die set下模座dimension n. 尺寸dimensional tolerance n. 尺寸公差dowel pin固定销dish gate 盘形浇口dip mold 浸渍成形distort v. 扭曲double stack mold 双层模具draft angle n. 拨模斜度drying 烘干duplicated cavity plate 复板模dwell time n. 驻留时间dye n. 染料Eedge gate 侧缘浇口ejector mark n. 顶出痕迹ejection pin n. 顶出杆/推顶锁 /脱模锁ejection plate n. 推顶板/脱模板ejection rod n. 脱模板拉杆elastomer n. 弹性体electrical discharge machining (EDM) n. 电火花加工electroformed mold 电铸成形模encapsulation molding 注入成形epoxy n. 环氧树脂eq-height sleeves=spool等高套筒expander die 扩径模extruder n. 挤出机extrusion n. 挤出，挤塑extrusion die 挤出模extrusion molding 挤出成形Ffabricate v. 制造family mold 反套制品模具fan gate 扇形浇口fantail die 扇尾形模具fiber n. 纤维feature die公母模female die母模(凹模) fiberglass n. 玻璃纤维fiber reinforcement n. 纤维增强film n. 薄膜film gate 薄膜浇口fire retardant n. 阻燃剂fishtail die 鱼尾形模具flash 飞边/溢料flash gate 闸门浇口flash mold 溢料式模具flaw/scratch 刮伤flexural modulus 弯曲模数flexural strength 抗弯强度flow line 流痕flow mark n. 流痕flow rate n. 流动速率fluorescent adj. 荧光fluorescent brightener n. 荧光增白剂foam n. 泡沫fuse v. 熔合Ggang dies 复合模gas assisted injection molding n. 气辅注射成型gate n. 浇口gate design 浇口设计gate mark n. 浇口痕gear n. 齿轮grinder n. 研磨机 /磨床gas mark 烧焦glazing 光滑gloss 光泽foam forming 发泡成形forming die 成型模forging roll 轧锻gravity casting 重力铸造groove punch压线冲子guide pin导正销guide plate定位板guide pad导料块gypsum mold 石膏铸模Hheat conduction n. 热传导heater band n. 加热圈heat treatment n. 热处理hesitation 迟滞high density polyethylene (HDPE) n. 高密度聚乙烯high impact plastic n. 高抗冲塑料high impact polystyrene n. 高抗冲聚苯乙烯hobbing n. 滚铣/挤压制模 /切压制模holding n. 保压hollow(blow) molding 中空(吹出)成形hot runner n. 热流道hot chamber die casting 热室压铸hot forging 热锻hot-runner mold 热流道模具Iimpact strength n. 冲击强度ingot mold 钢锭模injection n. 注射/注塑injection mold 注塑模injection molding 射出成形injection molding machine n. 注塑机injection pressure 注塑压力injection speed 注塑速度inner stripper内脱料板inner guiding post内导柱inner hexagon screw内六角螺钉insert入块(嵌入件)insulated runner n. 绝热流道/保温流道insulation layer n. 绝热层internally heated runner n. 内加热流道internal void n. 内部空腔investment casting 精密铸造Jjoint n. 接头/连接/Llancing die 切口模laminating method 被覆淋膜成形lancing die 切口模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具laser n. 激光laser cutter n. 激光切割机lathe n. 车床lifter guide pin浮升导料销lifter pin顶料销located block定位块located pin定位销loading shoe mold 料套式模具loose detail mold 活零件模具long nozzle 延长喷嘴方式loose mold 活动式模具louvering die 百叶窗冲切模lost wax casting 脱蜡铸造low density polyethylene n. 低密度聚乙烯low pressure casting 低压铸造lower plate下模板lower sliding plate下滑块板lower stripper下脱料板Mmale die公模(凸模)main runner 主流道manifold die 分歧管模具melt v. 熔融melt index n. 熔融指数mill (metal) v. 铣machining n. 机加工machining path n. 加工路径manufacture v. 制造matched die method 对模成形法matched mould thermal forming 对模热成形模meld line n. 融合线metal machining n. 金属加工melt temperature 熔化温度milling machine n. 铣床model n. 模型modular mold 组合式模具monomer n. 单体mold n. 模具mold cavity n. 模具型腔mold life n. 模具寿命mold temperature 模具温度molding conditions 成型条件modular mold 组合式模具multi color injection molding n. 多色注塑multi-cavity mold 多模穴模具multi-gate mold 复式浇口模具multi shot injection molding n. 多次注料注塑Nnozzle n. 喷嘴Nylon n. 尼龙O offset bending die 双折冷弯模具outer bush外导套outer guiding post外导柱outer stripper外脱料板oxidation resistance n. 耐氧化性oxidize v. 氧化Ppackaging n. 包装packing n. 补料palletizing die 叠层模parison n. 型坯part n. 零件parting line n. 分模线parting plane n. 分模面pierce die 冲孔模pin销pinhole gate n. 针孔形浇口pinpoint gate 点浇口plain die 简易模plaster mold 石膏模plastic n. 塑料plasticity n. 塑性plasticizer n. 增塑剂plotter n. 绘图机polish v. 抛光porous adj. 多孔precise adj. 精密polycarbonate (PC) n. 聚碳酸酯polyethylene n. 聚乙烯polyester n. 聚酯polymer n. 聚合物（体） /高聚物polymerization n. 聚合polystyrene n. 聚苯乙烯polyurethane n. 聚氨脂polyvinyl chloride (PVC) n. 聚氯乙烯porous mold 通气性模具positive mold 全压式/挤压式模具pressure die 压紧模profile die 轮廓模progressive die 顺序模portable mold 手提式模具positive mold 全压式模具powder forming 粉末成形powder metal forging 粉末锻造precision n. 精度precision injection machine n. 精密注塑机precision forging 精密锻造precision molding n. 精密模塑preform n. 预成型preform molding n. 预成型模塑press forging 冲锻pressure die 压紧模profile die 轮廓模progressive die 连续模/顺序模prototype mold 雏形试验模具process v. 处理chǔlǐ；加工production line n. 生产线prototype mold 雏形试验模具prototype n. 原型punch冲头punch set上模座punching die 落料模punch holder上夹板punch pad上垫板Qquench v. 淬火Rraising(embossing) 压花起伏成形re-entrant mold 倒角式模具reel-stretch punch卷圆压平冲子regrind n. 回用料regrind usage 次料使用resin n. 树脂rib n. 肋条rib stiffener n. 加强肋ribbon punch压筋冲子rigidity n. 刚性ring gate 环形浇口ripple n. 波纹/皱纹riveting die 铆合模rocking die forging 摇动锻造roller滚轴rotary forging 回转锻造rotational molding 离心成形rough adj. 粗糙round punch圆冲子rubber n. 橡胶 /橡皮írubber molding 橡胶成形runner n. 流道runner design 流道设计runner plat 浇道模块runner system浇道系统runnerless adj. 无流道runnerless injection mold n. 无流道注塑模具Ssand mold casting 砂模铸造scale n. 比例schematic n. 图解screw speed 螺杆转速seal v. 密封secondary runner 次流道sectional die 拼合模/对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套shearing die 剪边模shell casting 壳模铸造short shot n. 短射shot n. 注料shot size n. 注塑量shrinkage 收缩(率)side core n. 侧性芯side gate 侧浇口silicon n. 聚硅氧烷silicon rubber n. 硅橡胶simulate v. 模拟single cavity mold 单腔模具single gate mold n. 单浇口模具sink mark n. 凹痕 /缩痕sinter forging 烧结锻造six sides forging 六面锻造slag well 冷料井slide n. 滑动阀sliding block滑块sliding dowel block滑块固定块special shape punch异形冲子spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板stop screw止付螺丝stripper pad脱料背板stripping plate内外打(脱料板) supporting block for location定位支承块slit gate 缝隙浇口slush molding 凝塑成形softener n. 软化剂solid forging die 整体/拼合锻模splay 银纹split forging die 拼合锻模split mold 分割式模具/双并式模具sprue 注道/ 浇口/溶渣sprue/cold material trap 浇道/冷料井sprue gate 射料浇口，直浇口sprueless mold 无注道残料模具sprue lock pin 料头钩销(拉料杆)sprue puller 拉杆sprueless mold 无射料管方式/无注道残料模具squeeze casting 高压铸造squeezing die 挤压模steam channel n. 汽道stabilizer n. 稳定剂stamped punch字模冲子stamping n. 冲压stainless steel n. 不锈钢stiffening rib punch = stinger 加强筋冲子strain n. 应变streak n. 条纹 /条痕stretch form die 拉伸成形模stress n. 应力stripper n. 脱模器/顶出器stripper ring n. 脱模圈submarine gate 潜伏浇口surface defect n. 表面缺陷surface treatment n. 表面处理surface check 表面裂痕swing die 振动模具symmetrical adj. 对称symmetry n. 对称swaging 挤锻sweeping mold 平刮铸模Ttab gate 搭接浇口Teflon n. 特氟隆temper v. 回火tensile strength n. 抗张强度tensile elongation 延伸率thermoforming n. 热成型thermoplastic n. 热塑性塑料 adj. 热塑性thermoset n. 热固性塑料 adj. 热固性three-dimensional adj. 三维空间three plates mold 三片式模具tie bar n. 连接杆tolerance n. 公差tool mark n. 刀痕tool steel n. 工具钢top plate上托板（顶板）top block上垫脚transfer molding 转送成形trimming die 切边模trimming punch切边冲子tunnel gate 隧道式浇口Uultrasonic welder n. 超声波焊接机undercut n. 凹孔unit cost n. 单价unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具up stripper上脱料板upper plate上模板upper holder block上压块upper mid plate上中间板Vvacuum n. 真空valve gate阀门浇口vented injection molding n. 排气式注塑成型viscosity n. 黏度/黏性void 缩孔vulcanize v. 硫化Wwarm forging 温锻warpage n. 翘曲变形wear n. 磨损wear resistance n. 耐磨损性weld line n. 熔接线wire spring圆线弹簧working drawing n. 工程图yoke type die 轭型模机械设备:3D coordinate measurement 三次元量床boring machine 搪孔机contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机driller 钻床EDM=Electron Discharge Machining 放电加工electrical sparkle 电火花engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机grinder 磨床horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床lathe车床linear cutting 线切割miller 铣床milling machine 铣床planer |刨床punching machine 冲床robot机械手welder 电焊机分类（汉英）一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar 唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin五术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct c ut on B-plate. 内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity 均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrod根据国家标准，以下为部分塑料模具成形术语的标准翻译。

模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。

模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 光滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性nài mósǔn xìng abrasive n. 磨料móliàoaccelerator n. 促进剂cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelì additive n. 添加剂tiānjiājìadhere v. 黏附niánfùadhesion n. 黏合niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíng blow molding machine n. 吹塑机chūisùjībrittle adj. 脆性cùixìngbubble n. 气泡qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢tànsù gāngcasting n. 铸造 zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngq iāngchemical resistance n. 耐化学腐蚀性nài huàxué fǔshí xìngchip v. 削xiāo，凿záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmó dūnwèicomputer aided design (CAD) n. 电脑辅助设计diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂 zhuósèjìcomposite n. 复合材料fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquè guǎndàocooling rate n. 冷却速率lěngquè sùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性nài fǔshí xìngcure v. 固化gùhuàcustom adj. 定制dìngzhìcycle time n. 循环时间xúnhuán shíjiānDdegassing n. 排气páiqìdensity n. 密度mìdùdeform v. 变形biànxíngdie n. 冲模chòngmódie casting n. 压铸yāzhù，模铸mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间zhùliú shíjiāndye n. 染料ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchū gān，推顶锁tūidǐng suǒ，脱模锁tuōmó suǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmó bǎnejection rod n. 脱模板拉杆t uōmó bǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuā jiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维增强xiānwéi zēngqiángfilm n. 薄膜báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料yìliàoflow mark n. 流痕liúhénflow rate n. 流动速率liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫pàomòfuse v. 熔合rónghéGgas assisted injection molding n. 气辅注射成型 qìfǔzhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床móchuángHheat conduction n. 热传导rè chuándàoheater band n. 加热圈jiārè quānheat treatment n. 热处理rè chǔlǐhigh density polyethylene (HDPE) n. 高密度聚乙烯gāo mìdù jùyǐxī high impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxī hobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmó holding n. 保压bǎoyāhot runner n. 热流道rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射zhùshè，注塑 zhùsùinjection molding n. 注塑成型zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力zhùsù yālìinsulated runner n. 绝热流道juérè liúdào，保温流道 bǎowēn liúdào insulation layer n. 绝热层juérè cénginternally heated runner n. 内加热流道nèi jiārè liúdàointernal void n. 内部空腔nèibù kōngqiāngJjoint n. 接头jiētóu，连接liánjiēlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdù jùyǐxī Mmelt v. 熔融róngróngmelt index n. 熔融指数róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìng manufacture v. 制造zhìzàomeld line n. 融合线rónghé xiànmetal machining n. 金属加工jīnshù jiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型móxíngmonomer n. 单体dāntǐmold n. 模具mójùmold cavity n. 模具型腔mójù xíngqiāngmold life n. 模具寿命mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójù multicolor injection molding n. 多色注塑duōsè zhùsù multigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè z hùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙NílóngOoxidation resistance n. 耐氧化性nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒu plastic n. 塑料sùliàoplasticity n. 塑性sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物（体）jùhéwù(tǐ)，高聚物gāojùwù polymerization n. 聚合jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmì zhùsùjī precision molding n. 精密模塑jīngmì mósùpreform n. 预成型yùchéngxíngpreform molding n. 预成型模塑yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型yuánxíngpunch n. 冲头chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料húiyòngliàoresin n. 树脂shùzhīrib n. 肋条lèitiáorib stiffener n. 加强肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮xiàngpírunner n. 流道liúdàorunnerless adj. 无流道 wúliúdàorunnerless injection mold n. 无流道注塑模具wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēngshort shot n. 短射duǎnshè，欠料注射 qiànliào zhùshèshot n. 注料 zhùliào，注射 zhùshèshot size n. 注塑量zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道zhùdàosteam channel n. 汽道qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变yìngbiànstreak n. 条纹tiáowén，条痕tiáohénstress n. 应力yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐngchūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆liánjiēgānTeflon n. 特氟隆Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdù thermoforming n. 热成型rèchéngxíngthermoplastic n. 热塑性塑料rèsùxìng sùliào adj. 热塑性rèsùxìng thermoset n. 热固性塑料règùxìng sùliào adj. 热固性règùxìng three-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjù gāngUultrasonic welder n. 超声波焊接机chāoshēngbō hánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型páiqìshì zhùsù chéngxíng viscosity n. 黏度niándù，黏性 niánxìngvulcanize v. 硫化liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图根据国家标准，以下为部分塑料模具成形术语的标准翻译。