下载文档原格式
3.9 Digital input module SM 321; DI 16 x DC 24 V; (6ES7321-1BH02-0AA0) Wiring and block diagrams of SM 321; DI 16 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 321; DI 16 x DC 24 VTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 200 g Module-specific dataSupports isochronous mode noNumber of inputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.7 Digital input module SM 321; DI 32 x DC 24 V; (6ES7321-1BL00-0AA0) Wiring and block diagrams of SM 321; DI 32 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTerminal assignment of SM 321; DI 32 x DC 24 VThe figure below shows how channels are assigned to addresses (input byte x up to inputbyte x+3).[ [ [[3.37 Programmable digital IO module SM 327; DI 8/DO 8 x DC 24 V/0.5 A (6ES7327-1BH00-0AB0) Wiring and block diagram of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmable① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmableTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 120Weight ca. 200 gModule-specific dataSupports isochronous mode noNumber of inputs 8 digitalNumber of inputs/outputs 8, can be programmed separatelyCable length∙unshielded ∙shielded max. 600 m max. 1000 m3.26 Digital output module SM 322; DO 8 x DC 24 V/2 A; (6ES7322-1BF01-0AA0)Use of the module with high-speed countersPlease note when using the module in combination with high-speed counters:NoteWhen using a mechanical contact to switch on the 24-V power supply to SM 322; DO8 x DC 24 V/2 A, the module outputs will carry a "1" signal for the duration of ca. 50 µs dueto the circuit structure.Wiring and block diagram of SM 322; DO 8 x DC 24 V/2 A① Channel number② Status display - green③ Backplane bus interface3.22 Digital output module SM 322; DO 16 x DC 24 V/ 0,5 A; (6ES7322-1BH01-0AA0) Wiring and block diagram of SM 322; DO 16 x DC 24 V/ 0.5 A① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 16 x DC 24 V/0.5 A - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.32 Relay output module SM 322; DO 8 x Rel. AC 230 V; (6ES7322-1HF01-0AA0) Wiring and block diagrams of SM 322; DO 8 x Rel. AC 230 V① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 8 x Rel. AC 230 V - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 8Cable length∙unshielded ∙shielded max. 600 m max. 1000 mVoltages, currents, electrical potentialsRated power supply L+ to the relays 24 VDC Total current of outputs (per group) max. 4 A3.31 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)Reaction to a shutdown of the power supplyNoteThe internal 200-ms buffer capacitance discharges sufficient power after power off to allowthe user program to set a defined relay state.Wiring and block diagrams of SM 322; DO 16 x Rel. AC 120/230 V① Channel number② Status display - green③ Backplane bus interface6.6 Analog input module SM 331; AI 8 x 13 Bit; (6ES7331-1KF02-0AB0)Wiring: Voltage measurement① Voltage measurement (± 5 V, ±10 V, 1 V to 5 V, 0 V to 10 V)② Voltage measurement (± 50 mV, ± 500 mV, ± 1 V) (note the input resistance defined in the technical data)③ Equipotential bonding④ Internal supply⑤ + 5 V from backplane bus⑥ Logic and backplane bus interface⑦ Electrical isolation⑧ Multiplexer⑨ Analog digital converter (ADC)⑩ Current sourceFigure 6-10 Block diagram and terminal diagramWiring: Voltage measurement and current output① Internal supply② Analog-to-Digital Converter (ADC)③ Inputs: Voltage measurement④ Outputs: Voltage output⑤ Digital-to-Analog Converter (DAC)⑥ Backplane bus interface⑦ Equipotential bonding⑧ Functional groundFigure 6-50 Wiring and block diagramsWiring: 2 and 4-wire connection for voltage output① 2-wire connection: no compensation for line impedance② 4-wire connection: with compensation for line impedance③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-48 Wiring and block diagramsAnalog modules6.14 Analog output module SM 332; AO 4 x 12 Bit; (6ES7332-5HD01-0AB0)Wiring: 2 and 4-wire connection for voltage outputThe following Fig. represents the 2-wire connection with no compensation for line resistorsand the 4-wire connection with compensation for line resistors.① 2-wire connection, no compensation for line resistors② 4-wire connection, with compensation for line resistors③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-46 Wiring and block diagramsS7-300 Module dataManual, 08/2009, A5E00105505-06 405。
3.9 Digital input module SM 321; DI 16 x DC 24 V; (6ES7321-1BH02-0AA0) Wiring and block diagrams of SM 321; DI 16 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 321; DI 16 x DC 24 VTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 200 g Module-specific dataSupports isochronous mode noNumber of inputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.7 Digital input module SM 321; DI 32 x DC 24 V; (6ES7321-1BL00-0AA0) Wiring and block diagrams of SM 321; DI 32 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTerminal assignment of SM 321; DI 32 x DC 24 VThe figure below shows how channels are assigned to addresses (input byte x up to inputbyte x+3).[ [ [[3.37 Programmable digital IO module SM 327; DI 8/DO 8 x DC 24 V/0.5 A (6ES7327-1BH00-0AB0) Wiring and block diagram of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmable① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmableTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 120Weight ca. 200 gModule-specific dataSupports isochronous mode noNumber of inputs 8 digitalNumber of inputs/outputs 8, can be programmed separatelyCable length∙unshielded ∙shielded max. 600 m max. 1000 m3.26 Digital output module SM 322; DO 8 x DC 24 V/2 A; (6ES7322-1BF01-0AA0)Use of the module with high-speed countersPlease note when using the module in combination with high-speed counters:NoteWhen using a mechanical contact to switch on the 24-V power supply to SM 322; DO8 x DC 24 V/2 A, the module outputs will carry a "1" signal for the duration of ca. 50 µs dueto the circuit structure.Wiring and block diagram of SM 322; DO 8 x DC 24 V/2 A① Channel number② Status display - green③ Backplane bus interface3.22 Digital output module SM 322; DO 16 x DC 24 V/ 0,5 A; (6ES7322-1BH01-0AA0) Wiring and block diagram of SM 322; DO 16 x DC 24 V/ 0.5 A① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 16 x DC 24 V/0.5 A - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.32 Relay output module SM 322; DO 8 x Rel. AC 230 V; (6ES7322-1HF01-0AA0) Wiring and block diagrams of SM 322; DO 8 x Rel. AC 230 V① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 8 x Rel. AC 230 V - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 8Cable length∙unshielded ∙shielded max. 600 m max. 1000 mVoltages, currents, electrical potentialsRated power supply L+ to the relays 24 VDC Total current of outputs (per group) max. 4 A3.31 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)Reaction to a shutdown of the power supplyNoteThe internal 200-ms buffer capacitance discharges sufficient power after power off to allowthe user program to set a defined relay state.Wiring and block diagrams of SM 322; DO 16 x Rel. AC 120/230 V① Channel number② Status display - green③ Backplane bus interface6.6 Analog input module SM 331; AI 8 x 13 Bit; (6ES7331-1KF02-0AB0)Wiring: Voltage measurement① Voltage measurement (± 5 V, ±10 V, 1 V to 5 V, 0 V to 10 V)② Voltage measurement (± 50 mV, ± 500 mV, ± 1 V) (note the input resistance defined in the technical data)③ Equipotential bonding④ Internal supply⑤ + 5 V from backplane bus⑥ Logic and backplane bus interface⑦ Electrical isolation⑧ Multiplexer⑨ Analog digital converter (ADC)⑩ Current sourceFigure 6-10 Block diagram and terminal diagramWiring: Voltage measurement and current output① Internal supply② Analog-to-Digital Converter (ADC)③ Inputs: Voltage measurement④ Outputs: Voltage output⑤ Digital-to-Analog Converter (DAC)⑥ Backplane bus interface⑦ Equipotential bonding⑧ Functional groundFigure 6-50 Wiring and block diagramsWiring: 2 and 4-wire connection for voltage output① 2-wire connection: no compensation for line impedance② 4-wire connection: with compensation for line impedance③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-48 Wiring and block diagramsAnalog modules6.14 Analog output module SM 332; AO 4 x 12 Bit; (6ES7332-5HD01-0AB0)Wiring: 2 and 4-wire connection for voltage outputThe following Fig. represents the 2-wire connection with no compensation for line resistorsand the 4-wire connection with compensation for line resistors.① 2-wire connection, no compensation for line resistors② 4-wire connection, with compensation for line resistors③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-46 Wiring and block diagramsS7-300 Module dataManual, 08/2009, A5E00105505-06 405。
S7-300PLC数字量输出（输入输出）模块接线图分享前面给大家分享了有关于S7-300的数字量输入模块的接线图，今天给大家分享下数字量输出模块的接线图1、8点输出，24V DC，2A 322-1BF01-0AA02、8点输出，48-125V DC，1.5A 322-1CF00-0AA03、8点输出，120-230V AC，1A 322-1FF01-0AA04、8点输出，120-230V AC,2A 322-5FF00-0AB05、8点输出，继电器，2A 322-1HF01-0AA06、8点输出，继电器，5A 322-1HF10-0AA07、8点输出，继电器，5A，带过压RC滤波器保护322-5HF00-0AB08、16点输出，24-48V DC，0.5A 322-5GH00-0AB09、16点输出，24V DC，0.5A 322-1BH01-0AA010、16点输出，24V DC，0.5A，高速 322-1BH10-0AA011、16点输出，120-230V AC，1A 322-1FH00-0AA012、16点输出，继电器，8A 322-1HH01-0AA013、32点输出，24V DC，0.5A 322-1BL00-0AA014、32点输出，120V AC，1A 322-1FL00-0AA0数字量输入输出模块接线图1、SM323 8输入，8输出 323-1BH01-0AA02、SM323 16输入， 16输出 323-1BL00-0AA03、SM327 8点输入，8点输入或输出 327-1BH00-0AB0接线图来源于个人收集，若有不对的请指正，谢谢，由于图片过多，下次在分享数字量输出模块和模拟量模块的接线图。
谢谢-----------------End----------------好图文需要分享哦！。
3.9 Digital input module SM 321; DI 16 x DC 24 V; (6ES7321-1BH02-0AA0) Wiring and block diagrams of SM 321; DI 16 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 321; DI 16 x DC 24 VTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 200 g Module-specific dataSupports isochronous mode noNumber of inputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.7 Digital input module SM 321; DI 32 x DC 24 V; (6ES7321-1BL00-0AA0) Wiring and block diagrams of SM 321; DI 32 x DC 24 V① Channel number② Status display - green③ Backplane bus interfaceTerminal assignment of SM 321; DI 32 x DC 24 VThe figure below shows how channels are assigned to addresses (input byte x up to inputbyte x+3).[ [ [[3.37 Programmable digital IO module SM 327; DI 8/DO 8 x DC 24 V/0.5 A (6ES7327-1BH00-0AB0) Wiring and block diagram of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmable① Channel number② Status display - green③ Backplane bus interfaceTechnical specifications of SM 327; DI 8/DO 8 x DC 24 V/0.5 A, programmableTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 120Weight ca. 200 gModule-specific dataSupports isochronous mode noNumber of inputs 8 digitalNumber of inputs/outputs 8, can be programmed separatelyCable length∙unshielded ∙shielded max. 600 m max. 1000 m3.26 Digital output module SM 322; DO 8 x DC 24 V/2 A; (6ES7322-1BF01-0AA0)Use of the module with high-speed countersPlease note when using the module in combination with high-speed counters:NoteWhen using a mechanical contact to switch on the 24-V power supply to SM 322; DO8 x DC 24 V/2 A, the module outputs will carry a "1" signal for the duration of ca. 50 µs dueto the circuit structure.Wiring and block diagram of SM 322; DO 8 x DC 24 V/2 A① Channel number② Status display - green③ Backplane bus interface3.22 Digital output module SM 322; DO 16 x DC 24 V/ 0,5 A; (6ES7322-1BH01-0AA0) Wiring and block diagram of SM 322; DO 16 x DC 24 V/ 0.5 A① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 16 x DC 24 V/0.5 A - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 16Cable length∙unshielded ∙shielded max. 600 m max. 1000 m3.32 Relay output module SM 322; DO 8 x Rel. AC 230 V; (6ES7322-1HF01-0AA0) Wiring and block diagrams of SM 322; DO 8 x Rel. AC 230 V① Channel number② Status display - green③ Backplane bus interfaceSM 322; DO 8 x Rel. AC 230 V - Technical specificationsTechnical specificationsDimensions and weightDimensions W x H x D (mm) 40 x 125 x 117 Weight ca. 190 gModule-specific dataSupports isochronous mode noNumber of outputs 8Cable length∙unshielded ∙shielded max. 600 m max. 1000 mVoltages, currents, electrical potentialsRated power supply L+ to the relays 24 VDC Total current of outputs (per group) max. 4 A3.31 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)Reaction to a shutdown of the power supplyNoteThe internal 200-ms buffer capacitance discharges sufficient power after power off to allowthe user program to set a defined relay state.Wiring and block diagrams of SM 322; DO 16 x Rel. AC 120/230 V① Channel number② Status display - green③ Backplane bus interface6.6 Analog input module SM 331; AI 8 x 13 Bit; (6ES7331-1KF02-0AB0)Wiring: Voltage measurement① Voltage measurement (± 5 V, ±10 V, 1 V to 5 V, 0 V to 10 V)② Voltage measurement (± 50 mV, ± 500 mV, ± 1 V) (note the input resistance defined in the technical data)③ Equipotential bonding④ Internal supply⑤ + 5 V from backplane bus⑥ Logic and backplane bus interface⑦ Electrical isolation⑧ Multiplexer⑨ Analog digital converter (ADC)⑩ Current sourceFigure 6-10 Block diagram and terminal diagramWiring: Voltage measurement and current output① Internal supply② Analog-to-Digital Converter (ADC)③ Inputs: Voltage measurement④ Outputs: Voltage output⑤ Digital-to-Analog Converter (DAC)⑥ Backplane bus interface⑦ Equipotential bonding⑧ Functional groundFigure 6-50 Wiring and block diagramsWiring: 2 and 4-wire connection for voltage output① 2-wire connection: no compensation for line impedance② 4-wire connection: with compensation for line impedance③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-48 Wiring and block diagramsAnalog modules6.14 Analog output module SM 332; AO 4 x 12 Bit; (6ES7332-5HD01-0AB0)Wiring: 2 and 4-wire connection for voltage outputThe following Fig. represents the 2-wire connection with no compensation for line resistorsand the 4-wire connection with compensation for line resistors.① 2-wire connection, no compensation for line resistors② 4-wire connection, with compensation for line resistors③ Equipotential bonding④ Functional ground⑤ Internal supply⑥ Electrical isolation⑦ Backplane bus interface⑧ Analog-to-Digital Converter (ADC)Figure 6-46 Wiring and block diagramsS7-300 Module dataManual, 08/2009, A5E00105505-06 405。
1.CPU（1）cpu 312c集成DI-DO引出线（连接器X1）全球独家推出 全覆盖型省配线解决方案（2）313c集成AI-AO和DI的引出线（连接器X1）集成DI-DO引出线（连接器X2）数字I-O接线图313c-2dp313c-2 ptp（5）314c-dp集成AI-AO和DI的引出线（连接器X1）集成DI-DO引出线（连接器X2）数字I-O接线图数字与模拟I-O的接线图（6）314c-2ptp集成AI-AO和DI的引出线（连接器X1）集成DI-DO引出线（连接器X2）数字I-O接线图数字与模拟I-O的接线图2.功能模块POS 输入模块,用于带StartStop接口的超声波编码器位置检测 338-4BC01-0AB04输入，2输出 334-0CE01-0AA08 点输入，9-12-14 位分辨率 331-7KF02-0AB0,8点输入，用于热电偶 331-7PF11-0AB08点输入，增强型16位分辨率，4通道模式 331-7NF10-0AB02点输入，9-12-14位分辨率8点输入，13位分辨率 331-1KF01-0AB08点输入，用于热电阻 331-7PF01-0AB08点输入，增强型16位分辨率 331-7NF00-0AB05模拟量输出模块4点输出，16位 332-7ND02-0AB04点输出，11-12位 332-5HD01-0AB0 8点输出，11-12位 332-5HF00-0AB06数字量输入模块8 点输入，120-230V AC 321-1FF01-0AA08 点输入，120-230V AC, single root 321-1FF10-0AA016 点输入，24-48V DC 321-1CH00-0AA016 点输入，24V DC，低态有效 321-1BH50-0AA016 点输入，48-125V DC 321-1CH20-0AA0 16 点输入，120-230V AC 321-1FH00-0AA016点输入，24V DC 321-1BH02-0AA016点输入，24V DC，用于等时线模式下运行 321-1BH10-0AA016点输入，24V DC，用于等时线模式下运行 321-1BH10-0AA0 有诊断能力32 点输入，120V AC 321-1EL00-0AA032点输入，24V DC 321-1BL00-0AA07数字量输出模块8点输出，11-12位 332-5HF00-0AB08点输出，24V DC，0.5A，322-8BF00-0AB08点输出，24V DC，2A 322-1BF01-0AA08点输出，48-125V DC，1.5A 322-1CF00-0AA08点输出，120-230V AC，1A 322-1FF01-0AA08点输出，继电器，2A 322-1HF01-0AA08点输出，继电器，5A 322-1HF10-0AA08点输出，继电器，5A，带过压RC滤波器保护 322-5HF00-0AB016点输出，24-48V DC，0.5A 322-5GH00-0AB0 16点输出，24V DC，0.5A 322-1BH01-0AA016点输出，24V DC，0.5A，高速 322-1BH10-0AA0 16点输出，120-230V AC，1A 322-1FH00-0AA016点输出，继电器，8A 322-1HH01-0AA0 32点输出，24V DC，0.5A 322-1BL00-0AA032点输出，120V AC，1A 322-1FL00-0AA0 （8）数字量输入输出模块SM323 16输入， 16输出 323-1BL00-0AA0。
S7-300 通用型模拟量输入扩展模块（SM331）技术规范及接线图一、S7-300 通用型模拟量输入扩展模块（SM331）技术规范1、SM331技术规范1技术规范SM331型号6ES7 331-7KF02-0AB0 6ES7 331-7HF01-0AB0 6ES7 331-1KF01-0AB0 6ES7 331-7KB02-0AB0图片模拟量输入特性模拟量输入通道8模拟量输入，9/12/14位分辨率8模拟量输入，14位分辨率，用于等时模式下运行8模拟量输入，13位分辨率2模拟量输入，9/12/14位分辨率• 电阻测量模拟量输入点数 4 8 1所需前连接器20 针20 针40 针20 针时钟同步• 时钟同步运行否支持否否测量范围电压输入范围• 0 至+10 V• 1 至 +5 V• 1 至 +10 V• -1 V 至 +1 V• -10 V 至 +10 V • -2.5 V 至 +2.5 V • -250 mV 至 +250 mV • -5 V 至 +5 V 支持支持支持支持支持支持支持支持支持支持支持支持支持否支持支持否否支持支持支持支持支持支持支持2、SM331技术规范2图片接线图6ES7331-1KF01-0AA0 40针6ES7331-7HF01-0AB0 20针6ES7331-7KB02-0AB0 20针6ES7331-7KF02-0AB0 20针6ES7331-7NF00-0AB0 40针6ES7331-7NF10-0AB0 40针6ES7331-7PF01-0AB0 40针6ES7331-7PF11-0AB0 40针。
