MIM-3407H2F中文资料

安徽富信半导体科技有限公司ANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.FS3407 SOT-23-3L-30V P Channel Enhancement沟道增强型MOS Field Effect Transistor场效应管▉Absolute Maximum Ratings最大额定值Characteristic特性参数Symbol符号Rat额定值Unit单位Drain-Source V oltage漏极-源极电压BV DSS-30V Gate-Source Voltage栅极-源极电压V GS+20V Drain Current(continuous)漏极电流-连续I D（at T A=25°C）-4.1A Drain Current(pulsed)漏极电流-脉冲I DM-15A Total Device Dissipation总耗散功率P D(at T A=25°C)1200mW Thermal Resistance Junction-Ambient热阻RΘJA105℃/W Junction/Storage Temperature结温/储存温度T J,T stg-55~150℃▉Device Marking产品字标FS3407=X7XB**ANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.FS3407▉Electrical Characteristics电特性(T A=25℃unless otherwise noted如无特殊说明，温度为25℃)Characteristic 特性参数Symbol符号Min最小值Typ典型值Max最大值Unit单位Drain-Source Breakdown Voltage漏极-源极击穿电压(I D=-250uA,V GS=0V)BV DSS-30——VGate Threshold Voltage栅极开启电压(I D=-250uA,V GS=V DS)V GS(th)-1-1.5-2.4VZero Gate Voltage Drain Current零栅压漏极电流(V GS=0V,V DS=-30V)I DSS——1u AGate Body Leakage栅极漏电流(V GS=+20V,V DS=0V)I GSS——+100n AStatic Drain-Source On-State Resistance 静态漏源导通电阻(I D=-4.1A,V GS=-10V) (I D=-3.5A,V GS=-4.5V)R DS(ON)—40535568mΩDiode Forward Voltage Drop内附二极管正向压降(I SD=-4.1A,V GS=0V)V SD——-1.2VInput Capacitance输入电容(V GS=0V,V DS=-15V,f=1MHz)C ISS—572—pF Common Source Output Capacitance共源输出电容(V GS=0V,V DS=-15V,f=1MHz)C OSS—82—pF Reverse Transfer Capacitance反馈电容(V GS=0V,V DS=-15V,f=1MHz)C RSS—70—pF Total Gate Charge栅极电荷密度(V DS=-15V,I D=-4.1A,V GS=-10V)Q g—12—nC Gate Source Charge栅源电荷密度(V DS=-15V,I D=-4.1A,V GS=-10V)Q gs—2—nC Gate Drain Charge栅漏电荷密度(V DS=-15V,I D=-4.1A,V GS=-10V)Q gd—2—nC Turn-ON Delay Time开启延迟时间(V DS=-15V I D=-1A,R GEN=2.5Ω,V GS=-10V)t d(on)—4—ns Turn-ON Rise Time开启上升时间(V DS=-15V I D=-1A,R GEN=2.5Ω,V GS=-10V)t r—18—ns Turn-OFF Delay Time关断延迟时间(V DS=-15V I D=-1A,R GEN=2.5Ω,V GS=-10V)t d(off)—18—ns Turn-OFF Fall Time关断下降时间(V DS=-15V I D=-1A,R GEN=2.5Ω,V GS=-10V)t f—22—nsANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.FS3407■Typical Characteristic Curve典型特性曲线Figure1:Output Characteristics Figure2:Transfer CharacteristicsFigure3:On-Resistance vs.Drain Current Figure4:On-Resistance vs.TemperatureFigure5:Capacitance Characteristics Figure6:Gate-Charge CharacteristicsANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.FS3407■Typical Characteristic Curve典型特性曲线Figure7:Drain Current vs.Temperature Figure8:Safe Operating AreaFigure9:Transient Thermal Response Curve安徽富信半导体科技有限公司ANHUI FOSAN SEMICONDUCTOR TECHNOLOGY CO.,LTD.FS3407▉Dimension外形封裝尺寸Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min MaxA 1.050 1.2500.0410.049 A10.0000.1000.0000.004 A2 1.050 1.1500.0410.045 b0.3000.5000.0120.020 c0.1000.2000.0040.008D 2.820 3.0200.1110.119E 1.500 1.7000.0590.067 E1 2.650 2.9500.1040.116 e0.950TYP0.037TYPe1 1.800 2.0000.0710.079 L0.600REF0.024REFL10.3000.6000.0120.024θ0o8o0o8o。

R MILE C4047UHF远程遥控模块操作说明１主意事项发射机工作时,忘记连接天线,可能导致严重后果。

使用高功率发射模式，发射电流高达500mA以上。

２接收机J umper1：用来绑定并且恢复PWM输出为低速标准模式,3003等模拟舵机使用这个模式J umper2：用来设定PWM输出为高速模式(数字舵机).配合发射机的高速率发射模式可以得到很低的延迟效果,模拟舵机使用此模式可能导致工作异常或者损坏PWM1-8：接舵机数据来源于遥控器输出接口PPM：(S-BUS):接PPM解码器或者XUFO根据发射机输入信号源,可配置成8通道输出模式和10通道输出模式遥控器为PCM模式,对码后PPM接口自动配置成10通道输出遥控器为8通道以上(不包含8通道)PPM模式,对码后PPM接口自动配置成10通道输出遥控器为8通道或者8通道以下PPM模式,对码后PPM接口自动配置成8通道输出配合TS404710通道PPM数据来源于遥控器的输出数据配合更高版本的发射机,10通道数据可来源于任意接口Analog:默认功能为RSSI输出丢失信号下的RSSI对应电压,得根据实地测量才能知道.配合更高版本的发射机使用可以配置成任意通道对应的模拟电压关系为1-2毫秒脉宽对应0-3.3V电压接收供电：使用任意接口都可以供电,电压极性如图所示,黑线表示负极输入电压3-5V为最佳范围,内置升压电路,低压下可以很好的工作如果供电噪声很大,则最低供电电压应该适当提高,例如4-5V范围供电电压小于2V,则有自动关机或者灵敏度降低的可能.供电电压越高,则发热越严重,夏天最高不应该超过6.5V(估计数据).冬天最高不超过8.4V(估计数据).接收机内置反接保护元件,但是过高的反接电压仍然可以导致损坏.接收机内部有静电易损元件,如果拆卸外壳,有可能导致损坏,接收机天线有静电防护功能,如有静电可以通过电池负极放电,使用万用表测量,天线振子和电池负极应该是短路的.3.发射机发射机射频输出接口为50欧姆SMA接口外螺纹,内孔小功率模式下,短时间空载不会烧毁发射模块大功率模式下,空载,会在很短的时间内导致功放过热损坏无论何种状态下,短路射频接口,都会在短时间内导致功放过热损坏使用n/4(n=1,3,5,7,9…..)波长同轴电缆,要小心,终端开路相当于输入端电路,功放会在几秒内烧坏.所以请尽量使用原配同轴电缆,并且不要做短路或者开路的尝试.近距离测试,请使用5W或者更大功率的假负载,长时间工作会很热,小功率假负载会烧坏.多功能按钮：按住按钮后开机,可以进入绑定模式开机后按住按钮5秒钟,可以控制接收机存储当前的所有通道位置输出功率选择开关：小功率30DB.大功率33DB大功率下电流有可能超过520mA,可能导致劣质的遥控器内部线路过热损坏某些版本遥控器内部具有过流保护功能,因此高功率模式可能因为保护电路动作,进行简单的改装可以避免这个问题速率：低速率为40hz高速率为66hz低速率下可以得到最高的灵敏度,高速率下可以得到很高的控制效果失控保护设定：启用或者非启用,启用状态,如果失控,先前储存所有通道位置,会作为PWM,PPM,输出数据.非启用状态,如果失控,则关闭PWM,PPM输出发射机供电为8.4-16V当电压小于8.4V有可能导致输出功率下降推荐使用3节大容量锂电池注意,发射机内部没有反接保护电路,反接电源会导致发射机报废.发射机默认设定波段为1波段,如果需要可以更改为2波段,做法为拆开后盖,焊接波段控制跳线.发射机只能识别10通道以内的PPM信号,输入过多通道的PPM信号,则多于通道会被忽略.4绑定RD4047接收机具有自动扫描机制,可以扫描模型上电子设备所发出的干扰信号.例如DSP处理器,机载电脑,舵机,晶振,摄像头,这些设备都会发出干扰信号,并且频率没有标准,所以绑定过程请务必按照如下步骤操作第一,将接收机以及其他所有电子设备安装到位第二,打开所有电子设备,并且使其处于正常工作模式,第三插入跳线到junper1后为接收机供电第四,按住发射机的多功能按钮,然后给发射机供电第五,等待发射机发出BBBB的声音,第六,发射机重新供电,接收机拔下跳线重新供电就OK了步骤34可以颠倒注意绑定过程是发射机和接收机双向通信的过程,发射机把工作模式传送给接收机,然后接收机根据工作模式进行扫描,扫描后的数据要回发给发射机,因此,绑定之后发射机和接收机储存的是相同的ID编码和跳频列表.如果更换接收机,可能因为工作环境不一样或者个体差异,导致跳频列表存在差异,因此更换接收机需要再次绑定.否则,接收机会搜索不到发射机,或者丢失频点,导致控制效果变差.5发射机蜂鸣器声音含义Bi小功率模式Bi Bi大功率模式Hua失控保护开扫描完成,开始发射Hua hua失控保护关闭扫描完成,开始发射绑定模式bi bi bi bi……连续表示绑定完成6LED含义接收机进入绑定模式接收机绑定成功接收机搜索模式接收机正常接收模式每接收一个数据闪烁一次看上去是连续的发射机正常发射模式发送2个数据闪烁一次看上去是连续的发射机绑定模式发射机高频部件损坏７如何得到最远的遥控距离1接收机天线拉直不能弯曲,2跟天线互成90度左右2接收天线附近材料为非导电材料,不能是金属或者碳纤维.2发射机有正确的天线安装角度.错误的安装角度,可使距离降低为百米内.3正确的对码操作4接收机附近没有350-550Mhz 频率大功率发射机5开阔地没有阻碍,6,正确的供电电压如果满足以上条件参考距离为20-60Km使用高增益天线,可以获得更远的距离８故障８故障排除排除1无法绑定的解决接收机指示灯频闪，发射机不BBB 鸣叫：看看是不是附近也有人正在进行绑定操作，很有可能接收机绑定到了别人发射机上。

单层运行
电梯百事通为您提供各种电梯配件资讯及技术资料
网址：
QQ:263729874
E-MAIL： hf_sc@
单层运行曲线由调速器内部根据电梯在减速点的实际速度和减速距 离自动计算给出，不需额外的单多层指令。
速度
V2/V3/V4
减速点 V2/V3/V4 信号断开
V<0.8Vnom
起动延时时间
控制输入信号 V1 信号
V2/V3/V4 信号 上/下方向信号 控制输出信号
运行接触器 抱闸接触器
V<0.3 V<0.8*V
V<0.3m/s
平层开关 V1 信号断开
平层点
时间
0.5s
图1 MICOVERT340变频器控制信号时序图
速
启动
度
V1+V4 信号给出
减速点 V4 信号断开
2.3 基本工作原理 电梯上常用的4极或6极电机可通过调节输入电压和频率改变其转
速。变频器将电网的三相交流电整流为直流电，再通过IGBT逆变为 交流电供给电机，交流电的电压和频率是根据要求的速度和力矩计 算出来的。 启动曲线按时间原则给出，制动曲线根据减速距离自动计算给出， 可实现零速停车，停车时无冲击感，可根据人的感觉设定多种理想 的运行速度曲线。 采用数字控制系统使可调节的环节减到最少，调速器自动确定控制 参数，并自动存储记忆，现场调试的工作量很小。
电梯百事通为您提供各种电梯配件资讯及技术资料
网址：
QQ:263729874
E-MAIL： hf_sc@
表3：
速度指令 Vn Vi V1 V2 V3 V4 UP DOWN
同时给出，电梯减速后遇到门区信号，V1速度 去掉，进入停车段。V1 应根据平层精度和停车 舒适感调整。

目录1 MICROMASTER 440 变频器的参数.................................................................... ................................... 1-1 1.1 MICROMASTER 440 变频器的系统参数.................简介.......................................................................1-2 1.2 快速调试(P0010=1)..... ................... ....................................................................................................1-4 1.3 命令和驱动数据组一概览........ ............. ......................... ......................................................................1-51.4 参数的说明......................................... .................................................................................................1-62 功能框图.............................................. .................................................................................................... 2-13 二进制互联连接（BiCo）功能................................................................................................................ 3-1 3.1 概述..................................................................................................................................................... 3-2 3.2 怎样进行BiCo 设置？......................................................................................................................... 3-2 3.3 BiCo 控制字和状态字的用法................................................................................................................. 3-43.4 BiCo 的连接............................................................ ............................................................................. 3-54 通讯....................................................................... .................................................................................. 4-1 4.1 采用的串行通讯接口............................................................................................................................ 4-2 4.2 串行通讯的工作情况............................ ................................................................................................. 4-2 4.2.1 概述.................................................................................................................................................... 4-2 4.2.2 RS485 的排障..................................................................................................................................... 4-3 4.3 采用通用的串行接口协议................................................................................ ................... ...................4-3 4.3.1 通讯报文的结构............................................................ ...................................................................... 4-4 4.3.2 USS 协议有关信息的详细说明........................................... .............................................................. 4-4 4.3.3 有效的数据字符.................................................................... .............................................................. 4-5 4.3.4 USS 的任务和应答.............................................................................................................................. 4-7 4.3.5 PKW 举例：..................................................................... .................................................................4-10 4.3.6 PZD 区域（过程数据区）................................................... .................................................................4-12 4.3.7 任务报文（主站→MICROMASTER4）................................................................................................4-12 4.3.8 应答报文（MICROMASTER4→主站）............................. ..................................................................4-13 4.3.9 MICROMASTER4 有关USS 通讯的参数设置.................. ..................................................................4-15 4.3.10 基本设定................................................................................................................... ........................4-16 4.3.11 一般的高级设置.................................................................................................................................4-16 4.3.12 较复杂的高级设置.............................................................................................................................4-17 4.3.13 与早期MICROMASTER 产品的兼容性....... . ...................................................................................4-17 4.3.14 读出和写入参数............................................... .................................................................................4-18 4.3.15 广播方式............................................................................................................................................4-19 4.3.16 通过USS 利用BiCo（二进制互联连接）...... . ....................................................................................4-19 4.4 PROFIBUS....................................................... . .................................................................................. 4-20 4.4.1 概况............................................................... . .................................................................................. 4-20 4.4.2 PROFIBUS 的使用........................................ .................................................................................... 4-20 4.5 PROFIBUS 模板............................................. . .................................................................................... 4-214.5.1 PROFIBUS 模板的特点................................. . .................................................................................. 4-215 高级操作板（AOP）..................................................... . .......................................................................... 5-1 5.1 警告和说明........................................................................ .................................................................... 5-4 5.1.1 特殊键的功能...................................................................................................................................... 5-4 5.2 应用举例............................................................................... . .............................................................. 5-5 5.2.1 采用AOP 控制单台变频器.......................................................... ....................................................... 5-55.2.2.3 网络控制－PC 方式.................................................................................................................... 5-7 5.2.3 参数的“读出”.............................................................. ................................................................. 5-8 5.2.4 参数的“下载”.................................................................. ............................................................... 5-9 5.2.5 AOP 的参数.................................................................... . ..................................................................5-10 5.2.6 从站方式和DriveMonitor 的操作................ . ....................................................................................5-10 5.2.7 MM3 参数的读出..................................... . .........................................................................................5-11 5.2.8 定时器的操作........................................... . .........................................................................................5-11 5.3 AOP 开始工作........................................................................................................................................5-14 5.3.1 接通电源和初始化............. . ...............................................................................................................5-14 5.3.2 语言文本的选择...................................... . ..........................................................................................5-15 5.3.3 开机“帮助”............................... . .....................................................................................................5-15 5.3.4 常规的操作屏幕.............................. . ..................................................................................................5-15 5.3.5 主菜单（机旁操作方式）.................................... . ..............................................................................5-16 5.3.6 请求等待................................................................ ............................................................................5-17 5.4 操作菜单................................................................................................................................................5-17 5.4.1 机旁操作方式下的操作........................................................................................................................5-17 5.4.1.1 通讯故障..........................................................................................................................................5-18 5.4.1.2 显示变频器的状态............... ............................................................................................................5-18 5.4.1.3 变频器类型的检验..................... ......................................................................................................5-18 5.4.2 主站方式下的操作................ . ............................................................................................................5-18 5.4.2.1 广播操作方式........................................... . .....................................................................................5-19 5.4.2.2 通讯故障..........................................................................................................................................5-19 5.5 选择操作方式.........................................................................................................................................5-19 5.5.1 机旁操作方式........................................................................................................... ......................... 5-20 5.5.2 主站方式................................................................................................................... ......................... 5-20 5.5.3 内部方式................................................................................................................... .........................5-20 5.5.4 从站方式.............................................................................................. ............................................. 5-20 5.5.5 PC 方式..................................................................................................... ........................................ 5-21 5.6 参数的访问............................................................................................................................................ 5-21 5.6.1 标准访问级的参数....................................................................... ...................................................... 5-21 5.6.2 功能键的使用................................................................................ .................................................... 5-22 5.6.2.1 屏幕显示滚动功能................................................................ .......................................................... 5-22 5.6.2.2 修改参数数值的某一位数字................................................ ............................................................ 5-22 5.6.2.3 跳转功能.......................................................................................................................................... 5-22 5.6.3 专家级参数................................................................................. ....................................................... 5-23 5.6.3.1 下标参数.............................................................................. ........................................................... 5-23 5.6.4 AOP 存储的参数组................................................................... ......................................................... 5-24 5.6.5 工程设计.................................................................................... ........................................................ 5-24 5.7 AOP 设定和组态.................................................................................................................................... 5-25 5.7.1 设定菜单..................................................................... ....................................................................... 5-25 5.7.1.1 背景亮度......................................................................................................................................... 5-25 5.7.1.2 屏幕对比度............................................................. ....................................................................... 5-26 5.7.1.3 用大字符显示.................................................................................................................................. 5-265.7.1.7 参数组的名称..................................................................................... ........................................... 5-27 5.7.1.8 设定时间/日期.......................................... ..................................................................................... 5-28 5.7.1.9 AOP 复位....................................................................................................................................... 5-28 5.8 故障指示............................................................................................................................................... 5-29 5.8.1 故障屏幕...................................................................................... ..................................................... 5-29 5.8.2 报警屏幕............................................................................................................................................ 5-30 5.8.3 多重故障................................................................................. .......................................................... 5-30 5.8.4 多重报警................................................................................. .......................................................... 5-30 5.8.5 故障和报警同时发生............................................................... .......................................................... 5-31 5.8.6 变频器的故障码....................................................................... ......................................................... 5-31 5.8.7 变频器的报警码........................................................................................ ........................................ 5-315.8.8 变频器的故障/ 报警记录（P0947）.............................................................................................. 5-316 编码器模板.............................................................................................................................................. 6-1 6.1 前言...................................................................................................................................................... 6-2 6.2 一般情况............................................................................................................................................... 6-3 6.3 安装...................................................................................................................................................... 6-4 6.3.1 准备工作................................................................................... ........................................................ 6-4 6.3.1.1 变频器的准备工作........................................................................................................................... 6-4 6.3.1.2 编码器模板的准备工作.......................................................... ......................................................... 6-5 6.3.2 接线方法的举例.................................................................................................................................. 6-8 6.4 调试................................................................................................................................................................. 6-9 6.4.1 TTL 编码器............................................................. ...........................................................................6-10 6.4.2 HTL 编码器................................................................... .....................................................................6-11 6.4.3 外接电源......................................................................... ...................................................................6-11 6.4.4 编码器模板的参数化........................................................ ..................................................................6-12 6.5 故障的排除............................................................................................................................................6-14 6.5.1 LED 指示灯............................................................ ...........................................................................6-14 6.5.2 故障码....................................................................... ........................................................................6-156.6 编码器模板的技术规格................................................... ......................................................................6-157 MICROMASTER 440 变频器的制动电阻..................................... ...........................................................7-1 7.1 技术数据...................................................................................... .........................................................7-2 7.2 安装.......................................................................................................................................................7-2 7.3 接线.......................................................................................................................................................7-2 7.4 制动电阻的接线和外形尺寸...................................................................................................................7-37.5 制动电阻的选型........................................................... .........................................................................7-48 选件安装图............................................................................................................................................... 8-1插图图4-1 典型的RS485 多站接口.................................................................................................................... 4-3 图4-2 通讯报文的结构................................................................................................................................. 4-4 图4-3 地址（ADR）的位号......................................................................................................................... 4-4图6-1 编码器模板的外观........................................................................................ .................................... 6-3 图6-2 变频器的铭牌........................................................................................................... ........................ 6-4 图6-3 选件的安装顺序........................................................................................................ ....................... 6-5图6-4 屏蔽接线端和PE 端子.......................................................................................... ......................... 6-5 图6-5 编码器模板上的LED 指示灯................................................................................. ......................... 6-6 图6-6 编码器模板的DIP 开关................................................................................................ .................... 6-7 图6-7 TTL 编码器的接线(5V DC) ................................................................................ ............................ 6-8 图6-8 HTL 编码器的接线(18V DC) .................................................................................. ........................ 6-8 图6-9 具有外接电源的编码器............................................................................................. ........................ 6-9 图6-10 编码器模板的安装方法....................................................................................... ............................ 6-9 图6-11 编码器模板上的LED 指示灯..........................................................................................................6-14表格表3-1 BiCo 的连接（r0019 至r0054）..................................... ................................................................. 3-5 表3-2 BiCo 的连接（r0055 至r1119）....................................... ............................................................. 3-6 表3-3 BiCo 的连接（r1170 至r2050）.......................................... .......................................................... 3-7 表3-4 BiCo 的连接（r2053 至r2294）............................................ ........................................................ 3-8 表4-1 任务识别标记ID 的定义............................................................ ....................................................... 4-7 表4-2 应答识别标记ID 的定义............................................................ ....................................................... 4-8 表4-3 对应答识别标记ID 的错误数值=“任务不能执行”的定义............... .................................................. 4-9 表4-4 PZD 区的结构..................................................................................... ..............................................4-12 表4-5 变频器的控制字（STW）................................................................ ................................................4-12 表4-6 变频器的状态字（PZD）.................................................................. ...............................................4-13 表4-7 实际例子........................................................................................ ....................................................4-14 表4-8 比较表（MICROMASTER4/早期生产的MIsCROMASTER 变频器）. ............................................4-18 表4-9 PROFIBUSSUB-D 插座的插针功能分配.............................................. ............................................ 4-23 表4-10 与数据传输速率相应的最大电缆长度................................................. ............................................ 4-23 表4-11 插头/座和电缆的订货号........................................................................ ............................. ........... 4-23 表4-12 技术数据.............................................................................................. ........................... .............. 4-24 表4-13 有关PROFIBUS 的订货资料................................................................... ...................................... 4-241 MICROMASTER 440 变频器的参数1.1 MICROMASTER 440 变频器的系统参数简介“参数说明”的编排格式如下。