Technical DataOriginal InstructionsDySC Dynamic Voltage Sag Corrector Specifications Bulletin Number 1608Topic PageSummary of Changes2Overview2Bulletin 1608N MiniDySC Dynamic Sag Correctors3Bulletin 1608P Dynamic Sag Correctors7Bulletin 1608M MegaDySC Dynamic Sag Correctors12Additional Resources15DySC Dynamic Voltage Sag Corrector SpecificationsSummary of ChangesThis publication contains new and updated information as indicated in the following table.Topic PageAdded Product Overview2Added 1608N Product Selection3Added Bulletin 1608N Accessories6Added 1608P Product Selection7Added Bulletin 1608P Accessories11Added Bulletin 1608M Product Selection12Added Additional Resources section15OverviewThe Bulletin 1608 line of Dynamic Sag Correctors (DySC) are a unique and exclusive industrial power quality solution. Each DySC uses patented double conversion inverter technology that protects against the voltage sags and momentary outages that account for much manufacturing downtime.•Protects against short-term sags and interruptions that can impact production•Machine to facility-wide protection•Single- and three-phase products•Up to 5 seconds of ride through•Battery-free solution - eliminates requirement to swap batteries every 3…5 yearsOverviewBulletin1608N1608P1608MType MiniDySC ProDySC MegaDySCAmp Range2...6 12...50 25...50 100/110 200400 (2400)Voltage Range120…240V AC208…480V AC380…480V ACMounting DIN Rail Mount Panel Mount Panel Mount Floor MountPhase / Wiring Single Phase / L-L and L-N Three Phase/ 3-Wire and 4-WireRide Through up to 5 sBatteries Not requiredEnclosure NEMA Type 1Operating Temperature Range0…40 °C (32…104 °F)2Rockwell Automation Publication 1608-TD001B-EN-P - November 2018DySC Dynamic Voltage Sag Corrector Specifications Bulletin 1608N MiniDySC Dynamic Sag Correctors1608N Product SelectionMiniDySC Single Phase Voltage Sag Corrector - DIN Rail MountRated Current [A] Line Voltage [V] Wiring Category Runtime Cat. No.2 A 120VL-N Standard 1608N-002A120V2SL-N Extended 1608N-002A120V2E 208VL-L Standard 1608N-002A208V1SL-L Extended 1608N-002A208V1E 240VL-L Standard 1608N-002A240V1SL-L Extended 1608N-002A240V1EL-N Standard 1608N-002A240V2SL-N Extended 1608N-002A240V2E3 A 208VL-L Standard 1608N-003A208V1SL-L Extended 1608N-003A208V1E 230VL-N Standard 1608N-003A230V2SL-N Extended 1608N-003A230V2E 240VL-L Standard 1608N-003A240V1SL-L Extended 1608N-003A240V1EL-N Standard 1608N-003A240V2SL-N Extended 1608N-003A240V2E6 A 120V L-N Standard 1608N-006A120V2S L-N Extended 1608N-006A120V2EMiniDySC Single Phase Voltage Sag Corrector - Panel MountRated Current [A] Line Voltage [V] Wiring Category Runtime Cat. No.12 A 120VL-N Standard 1608N-012A120V2SL-N Standard 1608N-012A120V2S-R 208V L-L Standard 1608N-012A208V1S 220V L-N Standard 1608N-012A220V2S 230V L-N Standard 1608N-012A230V2S 240VL-L Standard 1608N-012A240V1SL-N Standard 1608N-012A240V2S25 A 120VL-N Standard 1608N-025A120V2SL-N Extended 1608N-025A120V2E208VL-L Standard 1608N-025A208V1SL-L Extended 1608N-025A208V1E220VL-N Standard 1608N-025A220V2SL-N Extended 1608N-025A220V2ERockwell Automation Publication 1608-TD001B-EN-P - November 201834Rockwell Automation Publication 1608-TD001B-EN-P - November 2018DySC Dynamic Voltage Sag Corrector Specifications1608N Specifications25 A230VL-N Standard 1608N-025A230V2S L-N Extended 1608N-025A230V2E 240VL-L Standard 1608N-025A240V1S L-L Extended 1608N-025A240V1E L-N Standard 1608N-025A240V2S L-NExtended 1608N-025A240V2E 50 A120V L-N Standard 1608N-050A120V2S L-N Extended 1608N-050A120V2E 208V L-L Standard 1608N-050A208V1S L-L Extended 1608N-050A208V1E 220VL-N Standard 1608N-050A220V2S L-N Extended 1608N-050A220V2E 230VL-N Standard 1608N-050A230V2S L-N Extended 1608N-050A230V2E 240VL-LStandard 1608N-050A240V1S L-L Extended 1608N-050A240V1E L-N Standard 1608N-050A240V2S L-NExtended1608N-050A240V2EElectrical Input/Output (Normal Mode—Static Switch)2…6 A12…50 AConnection Configuration Series-connected with load. Under normal line condition, the static switch passes utility voltage directly to the load Standard Input Voltage DySC 1 PH: 120, 208, 220, 230, 240V Voltage Range±10%Current Overload (Trip above these levels) 110% continuous, 150% @ 10 s, 200% @ 0.5 s,300% @ 10 cycles, 400% @ 3 cycles, 1000% Instantaneous —Current Overload (Static Switch) for 12A, 50A models — 200% @ 30 s, 400% @ 5 s, 600% @ 0.5 s Current Overload (Static Switch) for 25A models —200% @ 30 s, 280% @ 5 s, 450% @ 0.5 sFrequency50/60 Hz Auto Sensing Frequency Range (tracking) 45…65 HzSurge Protection Device (SPD) Built-in 3-Layers consisting of MOVs and Capacitors Efficiency 250 VA >94%, 500 VA>97%, 750 VA >96% > 98%Phase (wiring) 1 phase (L-L & L-N) Detection Voltage 88.5% of rated voltageResponse Time (typical)0.7 ms detection, 1.2 ms inverter reaction (<2 ms)MiniDySC Single Phase Voltage Sag Corrector - Panel Mount (Continued)DySC Dynamic Voltage Sag Corrector SpecificationsElectrical Output (Sag Correction Mode—Inverter)Output Voltage Matches pre-sag input voltageVoltage Regulation +/- 5% typical, +5% / -13% of nominal maxOutput Current Rated RMSCrest Factor (at rated load) 1.45Load Power factor range -0.5…+0.9, DC component <2% of rated currentVoltage Waveform (typical) Sine waveVoltage Sag Correction TimesSingle Event87% to 50% voltage remaining 5 s SR and ERSags to zero voltage remaining 50 ms or 200 ms (standard or extended run time DySCs). Based on nameplate ratings with a power factor of 0.7 Multiple EventsMax Sag Correction Time 5 s cumulative usageSequential Sag Recovery 0 s (assuming cumulative run-time available)Full Recovery Time Max 5 minMechanical Specifications2…6 A12...50 AEnclosure Ratings NEMA 1 (IP20)Cooling Forced air (500VA, 750VA) or natural convection (250VA)Forced AirAccess Lower front for connections Lower front for servicing and connections Accessibility (Wiring)Pluggable compression terminal block DIN compression terminal blockCommunications / User Interface2…6 A12...50 AIndicators 3 LEDs: Overload Trip, Normal, Alarm Normal and Alarm LEDsConnectivity************************************@1A OUTPUT OK and ALARM contacts, Form A, 24V DC at 1 AEnvironmental2…6 A12...50 AAmbient Temperature0…+50 °C (+32…+122 °F)0…+40 °C (+32…+104 °F)Storage Temperature-40°C…+75 °C (-40…+167 °F)Relative Humidity0…95% non-condensingAltitude Rated current available to 1000 m (3300 ft).De-rate output current 10% per 1000 m, from 1000…3000 m (9900 ft).Audible Noise<50 dBA at 1 mRockwell Automation Publication 1608-TD001B-EN-P - November 201856Rockwell Automation Publication 1608-TD001B-EN-P - November 2018DySC Dynamic Voltage Sag Corrector Specifications1608N Approximate DimensionsApproximate dimensions are shown in inches (mm) unless otherwise indicated. Dimensions are not to be used for manufacturing purposes.1608N Accessories2…6 Amp – DIN Rail MountRun Time Rating (VA) H x W x D in. [mm]Shipping Weight lb. [kg] Standard (SR)250 8.3 x 3.4 x 6.3 [210.8 x 86.4 x 160] 4.8 [2.18] 500 9.3 x 3.4 x 7.8 [236.2 x 86.4 x 198.1] 6.3 [2.86] 750 9.3 x 3.4 x 7.8 [236.2 x 86.4 x 198.1] 6.7 [3.04] Extended (ER)2508.3 x 5.8 x 6.3 [210.8 x 147.3 x 160] 8.0 [3.63] 500 9.3 x 5.8 x 7.8 [236.2 x 147.3 x 198.1] 9.5 [4.31] 7509.3 x 5.8 x 7.8 [236.2 x 147.3 x 198.1]10.2 [4.63]12…50 Amp – Panel MountRun Time Rating (A) H x W x D in. [mm] Shipping Weight lb. [kg] Standard (SR) 12, 25 22 x 10 x 4 [550.8 x 254 x 101.6] 18.6 [8.44] 50 21 x 19 x 4 [533.4 x 482.6 x 101.6] 34.5 [15.5] Extended (ER)25 21 x 19 x 4 [533.4 x 482.6 x 101.6] 32.5 [14.7] 5021 x 19 x 7 [533.4 x 482.6 x 177.8]51.5 [23.4]Bulletin 1608 AccessoriesTypeDescriptionCat. No. Bulletin 1608N - Single PhaseBypass, Single Phase, 25A, up tp 240V, L-L1608N-BP025A240V1 Bypass, Single Phase, 25A, up to 240V, L-N 1608N-BP025A240V2 Bypass, Single Phase, 50A, up to 240V, L-L 1608N-BP050A240V1 Bypass, Single Phase, 50A, up to 240V, L-N1608N-BP050A240V2DySC Dynamic Voltage Sag Corrector Specifications Bulletin 1608P Dynamic Sag Correctors1608P Product SelectionProDySC Three Phase Voltage Sag CorrectorRated Current [A] Line Voltage [V] Wiring Category Runtime Cat. No.25 A 208V3-Wire Standard 1608P-025A208V3S3-Wire Extended 1608P-025A208V3E4-Wire Standard 1608P-025A208V4S4-Wire Extended 1608P-025A208V4E 380V3-Wire Standard 1608P-025A380V3S3-Wire Extended 1608P-025A380V3E4-Wire Standard 1608P-025A380V4S4-Wire Extended 1608P-025A380V4E 400V3-Wire Standard 1608P-025A400V3S3-Wire Extended 1608P-025A400V3E4-Wire Standard 1608P-025A400V4S4-Wire Extended 1608P-025A400V4E 415V3-Wire Standard 1608P-025A415V3S3-Wire Extended 1608P-025A415V3E4-Wire Standard 1608P-025A415V4S4-Wire Extended 1608P-025A415V4E 480V3-Wire Standard 1608P-025A480V3S3-Wire Extended 1608P-025A480V3E4-Wire Standard 1608P-025A480V4S4-Wire Extended 1608P-025A480V4E50 A 208V3-Wire Standard 1608P-050A208V3S3-Wire Extended 1608P-050A208V3E4-Wire Standard 1608P-050A208V4S4-Wire Extended 1608P-050A208V4E380V3-Wire Standard 1608P-050A380V3S3-Wire Extended 1608P-050A380V3E4-Wire Standard 1608P-050A380V4S4-Wire Extended 1608P-050A380V4E400V3-Wire Standard 1608P-050A400V3S3-Wire Extended 1608P-050A400V3E4-Wire Standard 1608P-050A400V4S4-Wire Extended 1608P-050A400V4E415V3-Wire Standard 1608P-050A415V3S3-Wire Extended 1608P-050A415V3E4-Wire Standard 1608P-050A415V4S4-Wire Extended 1608P-050A415V4ERockwell Automation Publication 1608-TD001B-EN-P - November 20187DySC Dynamic Voltage Sag Corrector Specifications50 A (cont’d)480V 3-Wire Standard 1608P-050A480V3S 3-Wire Extended 1608P-050A480V3E 4-Wire Standard 1608P-050A480V4S 4-Wire Extended 1608P-050A480V4E100 A 208V3-Wire Standard 1608P-100A208V3S3-Wire Extended 1608P-100A208V3E4-Wire Standard 1608P-100A208V4S4-Wire Extended 1608P-100A208V4E 380V3-Wire Standard 1608P-100A380V3S3-Wire Extended 1608P-100A380V3E4-Wire Standard 1608P-100A380V4S4-Wire Extended 1608P-100A380V4E 400V3-Wire Standard 1608P-100A400V3S3-Wire Extended 1608P-100A400V3E4-Wire Standard 1608P-100A400V4S4-Wire Extended 1608P-100A400V4E 415V3-Wire Standard 1608P-100A415V3S3-Wire Extended 1608P-100A415V3E4-Wire Standard 1608P-100A415V4S4-Wire Extended 1608P-100A415V4E 480V3-Wire Standard 1608P-100A480V3S3-Wire Extended 1608P-100A480V3E4-Wire Standard 1608P-100A480V4S4-Wire Extended 1608P-100A480V4E110 A 480V 3-Wire Standard 1608P-110A480V3S3-Wire Extended 1608P-110A480V3E3-Wire Extended 1608P-110A480V3E-HC 4-Wire Standard 1608P-110A480V4S4-Wire Extended 1608P-110A480V4E4-Wire Extended 1608P-110A480V4E-HCProDySC Three Phase Voltage Sag Corrector (Continued)Rated Current [A] Line Voltage [V] Wiring Category Runtime Cat. No.8Rockwell Automation Publication 1608-TD001B-EN-P - November 2018Rockwell Automation Publication 1608-TD001B-EN-P - November 20189DySC Dynamic Voltage Sag Corrector Specifications1608P Specifications200 A208V 3-Wire Standard 1608P-200A208V3S 4-Wire Standard 1608P-200A208V4S 380V 3-Wire Standard 1608P-200A380V3S 4-Wire Standard 1608P-200A380V4S 400V3-Wire Standard 1608P-200A400V3S 4-Wire Standard 1608P-200A400V4S 415V3-Wire Standard 1608P-200A415V3S 4-Wire Standard 1608P-200A415V4S 480V3-Wire Standard 1608P-200A480V3S 4-WireStandard 1608P-200A480V4S 3-Wire Standard 1608P-200A480V3S-HC (1)4-WireStandard1608P-200A480V4S-HC (1)(1)1608P-xx…-HC 200 A devices provide 78 ms ride-through time at zero volts, and includes an integrated three breaker bypass.Electrical Input/Output (Normal Mode—Static Switch)25/50 A110/110A200 A200 A HCConnection Configuration Series-connected with load. Under normal line condition, the static switch passes utility voltage directly to the load Standard Input Voltage DySC 3 PH: 208, 380, 400, 415, 480V 480VVoltage Range ±10% Current Overload 150% @ 30 s,400% @ 5 s,600% @ 0.5 s 200% @ 30 s,400% @ 5 s,600% @ 0.5 s150% @ 30 s 400% @ 5 s 600% @ 0.5 sFrequency50/60 Hz Auto Sensing Frequency Range (tracking) 45…65 Hz48…62 HzSurge Protection Device (SPD) Built-in 3-Layers consisting of MOVs and Capacitors Efficiency > 99% @ 480V Phase (wiring) 3 PH (3-Wire and 4-Wire)Detection Voltage 88.5% of rated voltageResponse Time (typical)0.7 ms detection, 1.2 ms inverter reaction (<2 ms)Electrical Output (Sag Correction Mode—Inverter)25/50 A 110/110A200 A200 A HCOutput Voltage Pre-sag rms voltageVoltage Regulation +/- 5% typical, +5% / -13% of nominal maxOutput Current Rated RMS, Not rated for DC loads: max allowable 2% DC loading.Crest Factor (at rated load) 1.45LoadPower factor range -0.5…+0.9, DC component <2% of rated current Voltage Waveform (typical)Sine waveProDySC Three Phase Voltage Sag Corrector (Continued)Rated Current [A]Line Voltage [V] Wiring Category Runtime Cat. No.DySC Dynamic Voltage Sag Corrector SpecificationsVoltage Sag Correction Times25/50 A 110/110A 200 A200 A HC Single Event87…50% voltage remaining 5 sAll three phases to zero voltage remaining 50 ms or 200 ms (SR or ER).Based on load at nameplateratings with a power factor of 0.733...50 ms or 133...200 ms(SR or ER). Based on load atnameplate ratings with a powerfactor of 0.750 ms based on nameplateratings with a power factor of 0.778 ms based on nameplateratings with a power factor of 0.7Multiple EventsMax Sag Correction Time 5 s cumulative usageSequential Sag Recovery 0 s (assuming cumulative run-time available)Full Recovery Time Max 5 minMechanical Specifications25/50 A 110/110A 200 A200 A HC Enclosure Ratings NEMA 1 (IP20)Cooling Filtered forced airAccess Front for servicing and connectionsAccessibility (Wiring)Screw terminal blocks Mechanical lugsCommunications / User Interface25/50 A 110/110A 200 A200 A HC Indicators LCD ScreenConnectivity SAG EVENT, OUTPUT OK, and ALARM contacts, Form A, 24V DC at 1 AEnvironmental25/50 A 110/110A 200 A200 A HC Ambient Temperature0…+40 °C (+32…+104 °F)Storage Temperature-40°C…+75°C (-40…+167 °F)Relative Humidity0…95% non-condensingAltitude Rated current available to 1000 m (3300 ft). De-rate output current 10% per 1000 m, from 1000…3000 m (9900 ft). Audible Noise< 55 dBA at 1 m<67 dBA at 1 m10Rockwell Automation Publication 1608-TD001B-EN-P - November 2018Rockwell Automation Publication 1608-TD001B-EN-P - November 201811DySC Dynamic Voltage Sag Corrector Specifications1608P Approximate DimensionsApproximate dimensions are shown in inches (mm) unless otherwise indicated. Dimensions are not to be used for manufacturing purposes.1608P Accessories25…50 AmpRun Time Rating (A) H x W x D in. [mm] Shipping Weight lb. [kg] Standard (SR) 25 32 x 26 x 14 [813 x 660 x 356] 277 [126] 50 38 x 38 x 14 [965 x 965 x 356] 330 [150] Extended (ER)25 32 x 26 x 14 [813 x 660 x 356] 307 [140] 5038 x 38 x 14 [965 x 965 x 356]398 [181]100/110 AmpRun Time Wiring Type H x W x D in. [mm]Shipping Weight lb. [kg] Standard (SR)3-Wire 57.1 x 29 x 24.7 [1449 x 737 x 627]787 [357] 4-Wire 772 [351] Extended (ER) 3-Wire 77.1 x 29 x 24.7[1957 x 737 x 627]937 [426] 4-Wire922 [419]200 AmpWiring Type H x W x D in. [mm]Shipping Weight lb. [kg] 3-Wire 78.6 x 42.4 x 34.6 [1983 x 1076 x 878]1,470 [667] 4-Wire1,408 [639]Bulletin 1608 AccessoriesTypeDescriptionCat. No. Bulletin 1608P - Three PhaseBypass, Three Phase, 25A, up to 480V1608P-BP025A480V3 Bypass, Three Phase, 50A, up to 480V 1608P-BP050A480V3 Bypass, Three Phase, 110A, up to 480V1608P-BP110A480V312Rockwell Automation Publication 1608-TD001B-EN-P - November 2018DySC Dynamic Voltage Sag Corrector SpecificationsBulletin 1608M MegaDySC Dynamic Sag Correctors1608M Product SelectionContact your local Rockwell Automation sales office or Allen-Bradley distributor for MegaDySC systems over 400A.T o ensure successful integration, the MegaDySC unit requires commissioning from factory authorized personnel.Rated Current [A]Line Voltage [V]Wiring Category Runtime Cat. No. 400A380V3-WireStandard 1608M-400A380V3S Extended 1608M-400A380V3E 4-Wire Standard 1608M-400A380V4S Extended 1608M-400A380V4E 400V3-WireStandard 1608M-400A400V3S Extended 1608M-400A400V3E 4-Wire Standard 1608M-400A400V4S Extended 1608M-400A400V4E 415V3-WireStandard 1608M-400A415V3S Extended 1608M-400A415V3E 4-WireStandard 1608M-400A415V4S Extended 1608M-400A415V4E 460V3-WireStandard 1608M-400A460V3S Extended 1608M-400A460V3E 4-Wire Standard 1608M-400A460V4S Extended 1608M-400A460V4E 480V3-WireStandard 1608M-400A480V3S Extended 1608M-400A480V3E 4-WireStandard 1608M-400A480V4S Extended1608M-400A480V4EDySC Dynamic Voltage Sag Corrector Specifications Bulletin 1608M SpecificationsElectrical Input/Output (Normal Mode—Static Switch)Connection Configuration Series-connected with load. Under normal line condition, the static switch passes utility voltage directly to the loadStandard Input Voltage DySC 3 PH: 380, 400, 415, 480VVoltage Range ±10%Static Bypass Current100% rated rms continuous, 150…400% @ 5 s, 400…600% @ 0.5 s, 600% @ 0.1 s Frequency 50/60 Hz Auto SensingFrequency Range (tracking) 45…65 HzSurge Protection Device (SPD) Output SPD, 80kA/modeEfficiency >99%Phase (wiring) 3 phases + Ground (3-wire models) or 3 phases + Neutral + Ground (4-wire models) Detection Voltage 88.5% of rated voltageResponse Time (typical) 0.7 ms detection, 1.2 ms inverter reaction (2 ms)Electrical Output (Sag Correction Mode—Inverter)Output Voltage Pre-sag rms voltageVoltage Regulation +/- 5% typical, +5% / -13% of nominal maxOutput Current Rated RMSNot rated for DC loads; max. allowable 2% DC loadingCrest Factor (at rated load) 1.45Load Power factor range -0.5…+0.9, DC component <2% of rated current Voltage Waveform (typical) Sine waveVoltage Sag Correction TimesSingle Event87…50% voltage remaining 5 s SR and ERAll three phases to zero voltage remaining 50 ms or 200 ms (standard or extended run time DySCs). Based on nameplate ratings with a power factor of 0.7Multiple EventsMax Sag Correction Time 5 s cumulative usageSequential Sag Recovery 0 s (assuming cumulative run-time available)Full Recovery Time Max 5 minMechanical SpecificationsEnclosure Ratings NEMA 1 (IP20)Cooling Filtered forced airCable Entry Top or bottom of switchboardAccess Front for servicing and connectionsAccessibility (Wiring)Mechanical LugsRockwell Automation Publication 1608-TD001B-EN-P - November 20181314Rockwell Automation Publication 1608-TD001B-EN-P - November 2018DySC Dynamic Voltage Sag Corrector Specifications1608M Approximate DimensionsApproximate dimensions are shown in inches (mm) unless otherwise indicated. Dimensions are not to be used for manufacturing purposes.Communications / User InterfaceIndicators LCD screenConnectivitySAG EVENT, OUTPUT OK, and ALARM contacts, Form A, 24V DC at 1 AEnvironmentalAmbient Temperature 0…+40°C (32…+104 °F)Storage Temperature -40°C…+75°C (-40…+167 °F)Relative Humidity 0…95% non-condensingAltitude Rated current available to 1000 m (3300 ft). De-rate output current 10% per 1000 m, from 1000…3000 m (9900 ft).Audible Noise<70dBA at 1 mRated Current [A]Run Time Wiring Type H x W x D in. [mm]Shipping Weight lb. [kg] 400Standard3-Wire 94 X 69.3 X 33.1 [2388 X 1759 X 840] 2867 lb [1300kg] 4-Wire 2831 lb [1284 kg] Extended 3-Wire 94 X 87.3 X 33.1 [2388 X 2216 X 840] 3731 lb [1692 kg] 4-Wire 3695 lb [1676 kg] 800Standard3-Wire 103 X 128.5 X 51.1 [2614 X 3264 X 1297]7800 lb [3538kg] 4-Wire 7800 lb [3538kg] Extended 3-Wire 103 X 164.5 X 51.1 [2614 X 4178 X 1297] 8632 lb [3915 kg] 4-Wire 8632 lb [3915 kg] 1200Standard3-Wire 103 X 165.5 X 51.1 [2614 X 4204 X 1297] 10,350 lb [1300kg] 4-Wire 10,350 lb [1300kg] Extended 3-Wire 103 X 219.5 X 51.1 [2614 X 5575 X 1297] 11,598 lb [1692 kg] 4-Wire 11,598 lb [1692 kg] 1600Standard3-Wire 103 X 202.5 X 51.1 [2614 X 5144 X 1297] 13,300 lb [6033kg] 4-Wire 13,300 lb [6033kg] Extended 3-Wire 103 X 274.5 X 51.1 [2614 X 6972 X 1297] 14,964 lb [6788 kg] 4-Wire 14,964 lb [6788 kg] 2000Standard3-Wire 103 X 239.5 X 51.1 [2614 X 6083 X 1297] 16,250 lb [7371kg] 4-Wire 16,250 lb [7371kg] Extended 3-Wire 103 X 329.6 X 51.1 [2614 X 8372 X 1297] 18,330 lb [8314 kg] 4-Wire 18,330 lb [8314 kg] 2400Standard3-Wire 103 X 276.5 X 51.1 [2614 X 7023 X 1297] 18,800 lb [8528kg] 4-Wire 18,800 lb [8528kg] Extended3-Wire 103 X 384.6 X 51.1 [2614 X 9769 X 1297]21,296 lb [9660 kg] 4-Wire21,296 lb [9660 kg]DySC Dynamic Voltage Sag Corrector Specifications Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.Resource DescriptionIndustrial Automation Wiring and Grounding Guidelines, publication 1770-4.1Provides general guidelines for installing a Rockwell Automation industrial system. Product Certifications website, rok.auto/certifications.Provides declarations of conformity, certificates, and other certification details.Y ou can view or download publications at /global/literature-library/ overview.page.Rockwell Automation Publication 1608-TD001B-EN-P - November 201815Allen-Bradley, LISTEN. THINK. SOLVE., Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.Publication 1608-TD001B-EN-P - November 2018Supersedes Publication 1608-TD001A-EN-P - July 2014Copyright © 2018 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.Rockwell Automation SupportUse the following resources to access support information.Documentation FeedbackY our comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the How Are W e Doing? form at /idc/groups/literature/documents/du/ra-du002_-en-e.pdf .Technical Support CenterKnowledgebase Articles, How-to Videos, FAQs, Chat,User Forums, and Product Notification /knowledgebaseLocal Technical Support Phone Numbers Locate the phone number for your country./global/support/get-support-now.pageDirect Dial Codes Find the Direct Dial Code for your product. Use thecode to route your call directly to a technical supportengineer./global/support/direct-dial.pageLiterature LibraryInstallation Instructions, Manuals, Brochures, and Technical Data./literatureProduct Compatibility and Download Center (PCDC)Get help determining how products interact, check features and capabilities, and find associated firmware./global/support/pcdc.pageRoc kw ell Otomasyon Ticaret A .Ş., K ar Plaza İş Mer k ezi E B lo k K at:6 34752 İçeren köy, İstanbul, T el: +90 (216) 5698400Rockwell Automation maintains current product environmental information on its website at /rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page .。
1608芯片
1608芯片是一种封装形式的电子元器件，其尺寸为16mm x 8mm。
该芯片具有多种功能，可以被广泛应用于不同的电子设备中。
首先，1608芯片具有很高的集成度，可以集成多个功能模块于一个芯片中。
这意味着在电路板上使用1608芯片时，可以减少元器件数量，从而降低系统成本并提高电路板的可靠性。
其次，1608芯片具有较高的性能。
它可以提供较高的计算速度和较大的存储容量，从而满足对高性能处理和大容量数据存储的需求。
此外，它还可以同时处理多个任务，提高系统的效率。
除此之外，1608芯片还具有较低的功耗。
它采用先进的制程工艺和功耗优化设计，可以在低功耗情况下实现高性能的运算和处理。
这使得1608芯片非常适合于便携式电子设备，如智能手机、平板电脑和可穿戴设备等。
1608芯片还具有较好的可靠性和稳定性。
它采用高质量的材料和生产工艺，经过严格的测试和筛选，以确保在各种条件下均能稳定运行。
因此，它可以满足各种严苛的工作环境和使用场景下的要求。
最后，1608芯片具有丰富的接口和通信功能。
它支持多种通信协议和接口标准，如UART、SPI、I2C、USB等，可以方便地接入其他设备和传输数据。
这进一步扩展了1608芯片的
应用范围，使其可以与其他设备进行联网和互联互通。
总之，1608芯片是一种功能强大、性能优良、功耗低、可靠稳定的电子元器件。
它在电子设备中有着广泛的应用，可以提供高性能的运算和处理能力，满足不同领域的需求。
随着科技的不断发展，相信1608芯片的性能将会不断提升，为各种电子设备带来更多的创新和进步。
【碳企研究】一文详解日本东丽公司2021年最新版碳纤维产品规格、性能及主要应用领域摘要东丽株式会社成立于1926 年，其前身是东洋人造丝公司，1970 年1 月，东丽从公司名称中去掉“人造丝”一词，更名为“东丽株式会社”，是世界著名的以有机合成、高分子化学、生物化学为核心技术的高科技跨国企业，目前东丽在23个国家和地区拥有 226 家公司。
本公众号关于日本东丽公司已撰写70余篇原创类文章，更多有关东丽公司的精彩文章请点击日本东丽专辑（延伸阅读）。
本文主要介绍了2021年日本东丽公司发布的最新碳纤维产品规格、性能及应用。
2021年8月3日，日本东丽公司官方网站发布了公司最新版的碳纤维产品型号目录信息，与2020年碳纤维产品目录相比，此次在2021年最新版产品目录中增加了T700GC、T800GC、T1100SC三款新产品，而T700SC增加6k规格产品、T800SC增加12k规格产品，部分产品力学性能有所上调，如M30SC碳纤维拉伸强度由2020版的5490MPa提升至5690MPa，致使该款纤维断裂伸长率由之前1.8%提高到1.9%。
1东丽碳纤维最新性能指标日本东丽公司2021最新版碳纤维产品规格性能及2020版产品信息分别如下表1、2所示：表1：2021最新版东丽碳纤维产品性能指标表2：2020版东丽碳纤维产品性能指标通过对比表1、表2中产品信息，在日本东丽公司2021最新版产品目录中主要调整包括以下几部分：•增加三款新品种：在2021最新版产品目录中，增加了T700GC （强度4900MPa、模量240GPa）、T800GC（强度5880MPa、模量294GPa）、T1100SC（强度7000MPa、模量324GPa）三款新产品。
••增加两款新规格产品：在2021最新版产品目录中，T700SC增加6k规格产品、T800SC增加12k规格产品。
••删减一款规格碳纤维：在2021最新版产品目录中，M35JB型号碳纤维产品由原来6k、12k规格调整为6k规格产品，删除12k规格产品。
