SLC智能照明控制器V11.1

智能照明控制器使用说明一、安装与设置1.安装：将智能照明控制器安装在传统照明控制面板的位置。

确保安装牢固，并将电源线连接至电源插座。

2.连接：将智能照明控制器与照明系统连接。

根据控制器的接口类型选择正确的连接方式，并确保连接牢固可靠。

3.设置：打开智能照明控制器的设置界面，并按照界面的提示进行设置。

通常需要连接到控制器的无线网络，并进行设备认证和授权。

二、基本操作1.打开/关闭灯光：在智能照明控制器的界面上，找到相应的灯光控制按钮，点击按钮可以实现对灯光的打开和关闭。

2.调节亮度：在灯光控制界面上，可以找到亮度调节的滑块或标尺。

通过滑动滑块或拖动标尺来调整灯光的亮度。

3.变换色温：对于支持调节色温的灯具，智能照明控制器提供了相应的色温调节功能。

用户可以通过滑动滑块或拖动标尺来调整色温。

4.场景切换：智能照明控制器通常支持多种预设场景，比如阅读模式、休息模式、晚会模式等。

用户可以在界面上选择相应的场景，控制器将自动切换到该场景设定的灯光状态。

5.定时开关：智能照明控制器支持定时开关功能，可以根据用户设定的时间来自动打开或关闭灯光。

用户可以在界面上设置定时开关的时间和周期。

三、高级功能1.传感器控制：智能照明控制器通常配备了多种传感器，比如人体传感器、光照传感器等。

用户可以设置控制器根据传感器信号自动调整灯光状态。

比如，当控制器感知到有人进入房间时，自动打开灯光，在人离开后自动关闭灯光。

2.联动控制：用户可以将智能照明控制器与其他智能设备联动，实现更丰富的控制方式。

比如，可以将照明控制和窗帘控制联动，当户外亮度过高时，自动关闭窗帘并调暗灯光。

3.远程控制：智能照明控制器通常支持远程控制功能，用户可以通过手机APP或云端管理平台来控制灯光状态。

在外出或不在家时，可以通过手机远程打开或关闭灯光，实现远程控制。

4.统计与分析：智能照明控制器可以记录和统计照明系统的使用情况，比如每天的使用时间、每天的能耗等。

灯光控制系统方案一、系统概述系统原理概述系统所有的单元器件（除电源外）均内置微处理器和存储单元，由一对信号线（UTP5）连接成网络。

每个单元均设置唯一的单元地址并用软件设定其功能，通过输出单元控制各回路负载。

输入单元通过群组地址和输出组件建立对应联系。

当有输入时，输入单元将其转变为数字信号在系统总线上广播，所有的输出单元接收并做出判断，控制相应回路输出。

系统通过两根总线连接成网络。

总线上不仅为每个组件提供24伏直流电源，还加载了控制信号。

通过系统编程使控制开关与输出回路建立逻辑对应关系。

系统元件采用模块化结构、并已经有系统化产品、系统扩展方便。

同时，通过专用接口元件及软件，可能直截接入电脑进行实时监控，或接入以太网进行远程实时监控。

因此在设计时更加简单、灵活。

系统为分布式控制，模块化结构，可靠性高。

任何控制模块均内置CPU，每个输入模块（场景开关、多键开关、红外传感器等）都可直接与输出模块（调光器、输出继电器）通讯（发送指令→接受指令→执行指令），避免了集中式结构中央CPU一旦出现故障造成整个系统瘫痪的弱点。

与BA系统的集成诺雅照明控制系统是一个开放的系统，通过专用接口软件，可方便地与其他系统连接，如楼宇自控系统、门禁系统、保安监控系统、消防系统等。

Network系统结构图二、系统功能和优点智能照明控制系统在学校应用的功能和优点：1、实现照明控制智能化可用手动控制面板，根据一天中的不同时间，不同用途精心地进行灯光的场景预设置，使用时只需调用预先设置好的最佳灯光场景，使人产生新颖的视觉效果。

随意改变各区域的光照度。

2、美化环境以达到吸引学生的注意力好的灯光设计，能营造出一种温馨、舒适的环境，增添其艺术的魅力。

良好的环境可以培养学生对其产生更大的兴趣，从而得到更好的学习效果。

利用灯光的颜色、投射方式和不同明暗亮度可创造出立体感、层次感，不同色彩的环境气氛，不仅使学生有个很好的学习环境，而且还可以产生一种艺术欣赏感，对课程产生强烈的研究精神。

智能节能照明控制器“保瓦博士”S L C系列安装及使用手册广州保瓦电子科技有限公司目录一、安全注意事项 (1)二、概述 (2)三、功能 (2)3.1 控制 (2)3.2 保护 (3)3.3 界面 (3)3.4 通讯 (4)四、技术指标 (4)五、安装 (5)六、推荐接线图 (6)七、典型工作曲线 (11)八、菜单结构 (12)九、指示灯及按键功能 (13)十、操作说明 (14)10.1 查询与设置模式之间切换 (14)10.2 设置模式切换界面与参数编辑 (15)10.3 光控/时控 (16)10.4 时控输出 (18)10.5 时间设置 (18)10.6 天文设置 (19)10.7 启动设置 (20)10.8 输出设置 (20)十一、常见故障排除 (21)附录一：城市经纬度 (22)附录二、上位机数据通道表 (33)一、安全注意事项1.由于SLC系列智能节能照明控制器采用半导体功率器件，因此不能作为检修时的电气隔离使用，线路上应使用空气开关或带熔断器的刀闸作为电气隔离。

2.在接入电源的状况下，不管SLC系列智能节能照明控制器处在任何状态，均不得触摸SLC系列智能节能照明控制器的任何端子，否则将有触电危险！3.在SLC系列智能节能照明控制器的配线回路上必须使用相应容量的快速熔断器或断路器作为短路保护元件。

4.对于带有补偿电容的灯具，请将功能开关中的单灯补偿开关打开，并设置预热时间应大于5分钟。

5.光控探头应安装在不易被人为光源干扰的位置。

6.SLC系列智能节能照明控制器任何状态下都能设置参数，参数设置完毕后须将SLC系列智能节能照明控制器保持运行。

7.在停止状态下SLC系列智能节能照明控制器不起控制作用。

1二、概述SLC系列智能节能照明控制器是以微处理器技术和现代电力电子先进技术为基础开发的高性能产品，能有效的降压及限压，延长灯具的使用寿命，减少维护费用，降低维护人员的工作量，节能效果达10%-35%，投资少见效快。

What is the Leviton Intellect IntelligentFixture Control System?This system allows customers to easily implement wireless dimming, occupancy/vacancy sensing, multizone daylight harvesting, scene control and manual control using Leviton Lighting Intellect fixtures and an Intellect Keypad Room Controller. One installation delivers flexible individual fixture control and/or multi-zone control for a future proof system that can be simply configured using the Intellect App to meetever-changing business needs.Leviton Lighting Intellect Fixtures Integrate advanced lighting controls and enable wireless communication via a robust mesh network What are Leviton Lighting Intellect Fixtures?Intellect Keypad Room Controller Coordinates all Intellect devices in the space and provides dimming, switching and scene controlIntellect App for iOS & AndroidThe only setup tool needed; configures the system and wirelessly communi-cates with the Intellect Keypad Room Controller using Bluetooth technology•Leviton Lighting offers Intellect Embedded, Enabled and Intellect Compatible fixtures within the Intense, ConTech and Birchwood brands•Intellect fixtures are easy to install LED fixtures with built in wireless control•Delivers an easy LED and controls solution for retrofits and new construction•Assures compatibility with Intellect controls allowing the fixture to seamlessly operate with other Intellect enabled devices•Integrates wireless dimming, occupancy/vacancy sensing and multi-zone daylight harvesting capabilities• Enables wireless communication via a robust mesh network •Factory equipped by the fixture manufacturerWhat Does Embedded, Enabled and Compatible fixtures mean?Intellect Embedded signifies that the Intellect sensor andPower Pack is integrated within the fixture .Intellect Enabled signifies that the fixture houses the Intellect Power Pack and cable with the sensor adjacentWhat is the Keypad Room Controller?Provides the Bluetooth interfacefor connection to the IntellectApp via an Android or iOS smartdeviceUses the Intellect App toconfigure button operationto meet the unique lightingneeds of each spaceAlso known as “the brain” of the sys-tem, acts as the primary user interfaceand coordinates all the energy man-agement functions within the spacewithout requiring a gateway or hubWhat are the benefits of a Leviton Intellect Intelligent Fixture Control System solution? • Easy Energy Savings• Intellect fixtures are out-of-the-box, self-containedsolutions that can be used to comply with dimming,occupancy/vacancy sensing and daylight harvest-ing requirements for Title 24, ASHRAE 90.1 and IECC• Compliant with Design Lights Consortium (DLC)Advanced Lighting Control specifications• Easy Layout and Design• Each Intellect fixture integrates a sensor whichwirelessly communicates with the Keypad RoomController and other Intellect devices within thespace• No additional gateway or hub needed• Easy Installation• Plug and play operation with no expensivecommissioning required• Ladderless commissioning with the Intellect App• Easy Operation• Configure, monitor and control the system from anAndroid or iOS smart device with the Intellect App• Easily program the Intellect Keypad Room Controllerto meet the unique lighting needs of any space withthe Intellect AppHow do you install the Leviton Intelligent Fixture Control System solution?Easy 3 Step Installation:1. Install Intellect-enabledfixtures 2. Install Intellect KeypadRoom Controller3. Configure the systemwith the Intellect App The Intellect Solution• Programmable using any Bluetooth-enabled Android or iOS smart device using the Intellect App• Multi-location switching• Occupancy detection—minor motion coverage area is equivalent to fixture coverage area• Auto-ON/Auto-OFF—automatically turns the lightsON on occupancy, turns the lights OFF on vacancy• Manual-ON/Auto-OFF—upon occupancy, nothinghappens, user must push a button or control thelights from the app to turn them on; turns the lightsOFF on vacancy• Multi-zone daylight harvesting—no limit to number of zones• Closed loop daylight harvesting• Configurable dead band• Room daylight harvesting has two operating modes • CAP at Target—lights will never go brighter thanthe programmed target level• Override Allowed—lights can temporarilyoverride the daylighting target • Programmable Intellect Keypad Room Controller but-tons— assignable with one of the following behaviors• Scene—collection of groups at a level• Toggle—button turns an individual group ON/OFF• Room ON—all lights go to their target level or to MAXif they are not in a daylighting zone• Room OFF—all lights go OFF• Raise—lights get incrementally brighter from theircurrent position; lights that are off, stay off• Lower—lights get incrementally dimmer from theircurrent position; lower will only dim the lights to theirminimum value• User controlled fixture groups—no limit to number of groups• Integral scene support—scenes are collections of groups, each at their own level, programmed with afade time and recalled from a push button or the app。

智能照明控制系统介绍智能照明控制系统是一种利用先进的技术和方法，对照明系统进行智能化管理和控制的系统。

它可以实现灯光的自动调节、节能和智能化控制，提高照明的效果和舒适度，并减少能源的浪费。

下面将介绍智能照明控制系统的原理、特点和应用。

智能照明控制系统的原理是通过感应器和控制器的配合，实现对照明系统的智能控制。

感应器可以感知环境中的人体、光线等信息，将这些信息传输给控制器。

控制器根据收集到的信息来判断照明需求，从而控制灯光的开关、亮度和色温等参数。

智能照明控制系统还可以通过网络连接，实现远程控制和监控，方便用户对照明系统的管理。

1.自动调节：智能照明控制系统可以根据环境的光照强度和人体活动情况自动调节灯光的亮度和色温。

当环境光线变暗或有人活动时，系统可以自动增加灯光亮度，确保室内明亮舒适。

而在光线充足、无人活动时，系统会自动降低灯光亮度，节省能源。

2.节能环保：智能照明控制系统可以根据照明需求调整灯光的亮度，避免能源的浪费。

通过灯光的自动调节和定时开关等功能，可以实现节能效果，减少能源消耗，降低能源污染。

3.网络连接：智能照明控制系统可以通过网络连接，实现对照明系统的远程控制和监控。

用户可以通过智能手机、平板电脑等设备随时随地控制灯光的开关、亮度和色温等参数，方便快捷。

同时，系统还可以实时监测照明系统的工作状态，及时发现故障和异常，提高系统的可靠性和可管理性。

智能照明控制系统的应用非常广泛。

它可以广泛应用于各种公共场所和住宅，如办公楼、商场、酒店、学校、医院、家庭等。

在这些场所中，智能照明控制系统可以根据人员的活动情况和环境的光照强度，实现灯光的智能调节和控制，提供良好的照明效果和舒适度。

智能照明控制系统还可以与其他智能系统进行集成，实现更多的功能。

比如可以与安防系统集成，实现灯光的联动控制；可以与温控系统集成，根据室内温度调整灯光的色温；可以与音乐系统集成，实现灯光的音乐节奏同步等。

总的来说，智能照明控制系统是一种通过感应器和控制器对照明系统进行智能化管理和控制的系统。

智能照明控制模块使用说明一、安装1.打开智能照明控制模块的包装盒，取出其中的控制器和说明书。

2.插上控制器的电源线，在家庭用电插座上插上合适的插头，确保控制器能够正常供电。

3.将智能照明控制模块与要控制的灯具连接。

将控制器的灯具线插入灯具的电源插座，确保连接牢固。

4.将智能照明控制模块与路由器进行连接，可以通过网线或者Wi-Fi 进行连接。

具体操作请参考说明书中的详细步骤。

二、设置3.添加成功后，设置设备的基本信息，例如设备名称、位置等。

这些信息可以帮助用户更方便地识别和管理设备。

4.进入设备的设置界面，在设置界面中可以进行各种功能的设置，例如定时任务、远程控制、联动控制等。

根据实际需求进行设置。

三、使用1. 远程控制：用户可以通过手机App进行远程控制，无需在家的情况下就可以实现灯光的开关、亮度的调节等操作。

2. 定时任务：用户可以根据自己的作息时间，在App中设置定时任务，例如在晚上10点自动关闭卧室灯光、早上7点打开厨房灯光等。

3.联动控制：智能照明控制模块可以与其他智能设备进行联动，例如当有人经过感应器时，灯光自动亮起；当来电时，灯光自动变暗等。

4.分区控制：用户可以将不同的灯具分成不同的区域进行控制，例如客厅的灯具可以单独分为一个区域进行控制，卧室的灯具可以分为另一个区域进行控制。

5.情景模式：用户可以设置多个情景模式，根据不同的场景需求选择不同的情景模式。

例如晚上看电影时可以设置为电影模式，灯光自动调暗；早上起床时可以设置为起床模式，灯光自动渐亮等。

四、注意事项1. 在操作智能照明控制模块前，请确保控制器已经正常连接到电源，并且与手机App成功连接。

2.安装灯具时，请确保电源已经关闭，避免发生触电等危险情况。

3.使用智能照明控制模块时，请确保设备处于稳定的网络环境下，以保证控制命令的及时响应。

总结：智能照明控制模块是一种非常实用的智能家居设备，它能够提供更加便利和舒适的生活体验。

通过远程控制、定时任务、联动控制等功能，可以帮助用户实现灯光的智能控制。

Intelligent lighting control systemAbstract: Intelligent lighting control system the main aim is to save energy, smart lighting control system with a variety of "pre-set" control mode and control components, at different times on different degrees of illumination for accurate set-up and rational management of energy-saving. This automatic adjustment of the illumination means, take full advantage of the natural outdoor light, only when necessary when the lamp or light to the required brightness, use the least energy to ensure that the required illumination level, energy-saving effect is very clear, usually ranging from more than 30%.Keywords: Intelligent lighting control system bus-type star-shaped structure1 the use of intelligent lighting control system for the superiority of1.1 good energy saving effectIntelligent lighting control system using the main purpose is to save energy, smart lighting control system with a variety of "pre-set" control mode and control components, at different times on different degrees of illumination for accurate set-up and rational management of energy-saving. This automatic adjustment of the illumination means, take full advantage of the natural outdoor light, only when necessary when the lamp or light to the required brightness, use the least energy to ensure that the required illumination level, energy-saving effect is very clear, usually ranging from more than 30%. In addition, the intelligent lighting control system for fluorescent lamp dimming control, etc., due to the use of a fluorescent active tunable filter electronic ballast technology and reduce the harmonic content, to improve the power factor and reduce the low-voltage reactive power loss.1.2 to extend the life span of light sourceLight source can not only extend the life savings, but also significantly reduce the workload of lamp replacement, reducing the operating costs of lighting systems, management and maintenance becomes simple.Both the thermal radiation source, or gas discharge light source, voltage fluctuations are a major cause of light damage. Therefore, the effective suppression of the fluctuations in voltage can extend the life of light sources.Intelligent lighting control system can successfully suppress the surge voltage power grid, but also have a voltage limit and the conjugate stream functions of filtering, to avoid over-voltage and under-voltage damage to the light. The use of soft-start and soft turn-off technology, to avoid the impact of current damage to the light. Through this method, the light source to extend the life span of usually 2 to 4 times.1.3 to improve the working environment, improve efficiencyGood working environment is to improve the efficiency of a necessary condition. Good design and reasonable choice of light source, lamps and lighting quality control systems, can improve the quality of lighting.Intelligent lighting control system dimming control panel module to replace the traditional lighting of the level switch control is an effective way to control the overall room illumination value, thereby enhancing the uniformity of illumination. At the same time, this control method used in electrical components have also solved the stroboscopic effect, will not create uncomfortable, confused, feeling eyestrain.1.4 to achieve a variety of lighting effectsA wide range of lighting control, the same building can have a variety of artistic effect, for a lot of construction hyperchromic. Modern buildings, lighting is not simply to meet people on the visual effect of light and shade, they should have control of a variety of programs to make buildings more vivid, more artistic, giving a wealth of visual effects and aesthetics. As an example of a project, building the exhibition hall, lecture hall, lobby, atrium, etc., if with intelligent lighting control system, according to different times, different uses, different effects, using the corresponding pre-set scene control, can achieve the wealth of artistic effect.1.5 facilitate the management of maintenanceIntelligent lighting control system for the control of lighting based on the automatic control of modular-based, supplemented by manual control, preset lighting scenes to the parameters stored in the EPROM Digital, these information is very convenient to set up and replaced, so that building lighting management and maintenance easier.1.6 have a high economic rate of returnOur reference point for the Shanghai region, from energy-saving lights and provincial estimates of the two made a come to this conclusion: with three to five years, the owner can recover the basic intelligent lighting control system to increase the total costs. Intelligent lighting control system can improve the environment and improve employee productivity and reduce maintenance and management costs, but also for the owners to save a substantial amount of costs.2 intelligent lighting control system componentsWe know that the intelligent lighting control system of building control system is only one part of the. If you want to focus on the various control systems to the control center to control, then the control system must have the standard communication interface and protocol version. Although such a system integration is feasible in theory, but it is very difficult to put into practice. Thus, in engineering, intelligent management of our building a distributed system, distributed, that is relatively independent of each control subsystem, self-contained, the implementation of specific control, intelligent building management system control subsystem of the relative independence, self-contained, the implementation of specific control, intelligent building management system from the control subsystem is a signal collection and monitoring role.At present, the intelligent lighting control system in accordance with sub-network topology, the following two forms, namely, bus and star-shaped structure-based hybrid. Both forms have the characteristics of a number of bus more flexibility, easy expansion, control of relative independence, lower costs; mixed some high reliability, fault diagnosis and rule out the simple, easy access to the agreement, transfer rate higher.Engineering design, we consider the building of intelligent lighting control system as an independent subsystem, use of international standards and agreements of the communication interface text, into the intelligent building management systems. Intelligent lighting control system uses a distributed, distribution-based approach, that is, the dimming control unit is relatively independent, self-contained, non-interfering, through centralized management and information interfaces, and intelligent building managementsystem linked to the achievement of the building control center subsystem of the collection and monitoring of the signal. In short, the intelligent lighting control should be the main system is a centralized management, and the main trunk and information interface components consisting of the regional implementation of the same sample of control and signal networks; its subsystems should be a dimmer by the various types of modules , control panels, illumination detector dynamic and static and dynamic components consisting of detectors, respectively, of the regional implementation of the specific control of different networks, the main system and subsystems, such as between the components through the interface to connect, to achieve data transmission.3 Intelligent lighting control system and control of the control of the contentA project to control the use of intelligent lighting control system include the following categories: technology office hall, computer center and other important room, lecture hall, such as multi-function hall, exhibition hall, conference center, lobby and courtyard, walkways and elevators, such as the Office of Public site; building facade lighting in general and also by the intelligent lighting control systems to control switch signal.Control the content of the term of the Interpretation:(1) clock controlClock management, etc. through the electrical components, to achieve the normal work of regions for the state of lighting in different time control.(2) the automatic adjustment control illuminationThrough each module and illumination dimming dynamic electrical components such as detectors, to achieve under normal conditions in the regions for the normal work of the state of the automatic lighting dimming control, making the region, such as illumination will not be outside with the sunshine factors change, and always maintain the default value in the illumination around.(3) control of the regional sceneThrough each dimmer module and the control panel and other electrical components, to achieve under normal conditions in the regions for the normal work of the state of the scene lighting control switch.(4) static and dynamic detection of controlThrough each dimming modules and electrical components, such as movement detectors, to achieve under normal conditions in the regions for the normal work of the state of the automatic lighting control switch.(5) Reduction state of emergency controlThrough each of the normal lighting control module, such as dimming of the electrical components, to achieve a state of emergency for the normal work of the various districts in the state of lighting and to give up the number of relief, such as dimming control.(6) Manual remote controlThrough the infra-red remote control, to achieve under normal conditions in the regions for the normal work of the state of lighting control and manual control of the regional scene.(7) Emergency lighting controlHere mainly refers to the control of intelligent lighting control system to the specialregion by the implementation of the emergency lighting control, including the following two controls:1) under normal illumination and the automatic adjustment control of the regional scene with the regulation of the normal work of lighting the same manner as the control.2) a state of emergency automatic discharge dimming control, through each of the emergency lighting dimming control module, such as electrical components, to achieve a state of emergency for the regions under a state of emergency lighting dimmers, such as giving up control, so that the accident in the state of emergency lighting to reach 100%.These are the characteristics of intelligent lighting control systems analysis and office buildings in a specific application in a number of experiences, hoping to play the role of forward, so that the field of technology in the lighting to fully play its role.智能照明控制系统摘要：采用智能照明控制系统的主要目的是节约能源，智能照明控制系统借助各种不同的"预设置"控制方式和控制元件，对不同时间不同环境的光照度进行精确设置和合理管理，实现节能。

智能照明控制模块操作说明1.安装首先，将智能照明控制模块连接到电源，并将需要控制的灯具与控制模块连接。

确保连接稳固，并确保灯具的电源开关处于关闭状态。

2.连接网络将智能照明控制模块连接到无线网络。

通常，智能照明控制模块会有一个网络配置按钮或配对按钮，按下该按钮，然后使用手机或电脑的无线网络设置功能，连接到控制模块创建的网络。

连接成功后，返回智能照明控制模块的控制界面。

3.添加设备4.控制灯光开关在智能照明控制模块的控制界面中，可以看到所连接的所有灯具。

通过点击灯具图标或文字等选择需要控制的灯具，然后点击开关按钮，可以实现对灯光的开关操作。

5.调节亮度选择需要控制的灯具后，在控制界面中可以看到亮度调节的滑动条或按钮。

通过拖动滑动条或点击按钮，可以实现对灯光亮度的调节。

根据需要进行调节，直到达到满意的亮度。

6.改变颜色一些智能照明控制模块支持灯光颜色的变化。

通过控制界面中的颜色选择器、预设模式选择或色调、饱和度、亮度等调节方式，可以改变灯光的颜色。

选择所需颜色或模式后，观察灯光变化，可以实现对灯光颜色的改变。

7.设置定时任务智能照明控制模块通常支持设置定时任务。

在控制界面中，找到定时任务设置功能，选择需要设置定时的灯具，在设置界面中选择执行时间、操作方式等，完成定时任务的设置。

这样，灯具就可以在设定的时间自动执行相应的操作。

8.远程控制以上是智能照明控制模块的操作说明。

根据不同产品的具体特点，界面和操作方式可能会有所差异，但大致流程是类似的。

通过熟悉操作说明和不断实践，可以更好地掌握智能照明控制模块的使用方法，实现灯光的智能化控制。

Leviton Mfg. co., Inc. Lighting Management Systems20497 SW Teton Avenue, Tualatin, OR 97062 1-800-736-6682 Tech Line: 1-800-959-6004 Fax: 503-404-5594 /lms © 2009 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.S e c t o r o c c u p a n c y S e n s o r sSector occupancy Sensorspassive infrared and multi-technology occupancy sensors for the Sector Intelligent Lighting control SystemdEScrIptIoNThe Leviton Sector PIR Occupancy Sensor (OSC04-ISW) and the Multi-Technology Occupancy Sensor (OSC20-MSW) are low- voltage occupancy sensors that work in conjunction with a Sector Bus Controller (SBP00-00M) to activate light switching in response to room occupancy within a Sector Intelligent Lighting Control System. These sensors are part of a system that turns lights on and keeps them on while movement is detected within the sensor’s range, and conversely turns lights off when motion is no longer detected for a specified period of time. The Sector Occupancy sensors use a small semi-conductor heat detector located directly behind a multizone Fresnel optical lens. The overall range of the sensor can be configured and man-aged remotely using the SectorNET graphical user interface (GUI). The sensor responds to heat emitted by the human body within the range of detection.Leviton’s Multi-Technology Occupancy Sensor (OSC20-MSW) features both infrared and ultrasonic sensing capabilities to automatically control lighting. This sensor takes advantage of the latest microprocessor-based technology to continually adjust and optimize its performance to changing conditions. Ultrasonic technology detects motion (including small motion) by noting changes in reflected sound waves. Infrared tech-nology detects movement of heat-emitting bodies. The combination of technologies yields a sensor with maximum sensitivity that is not prone to false triggers from air conditioning or other small vibrations.appLIcatIoNSThe Leviton Sector Occupancy Sensors are ideal for use in office buildings, schools, medical offices, restaurants, and government facilitiesa nd any other location that could benefit from the cost savings and energy efficiency of a con-trolled lighting environment.The Sector family of products provides a scalable solution that allows you to install a maximum of 253 Bus Controllers, controlling a maximum of 64 devices each, for complete system flexibility and maximum coverage in any application.• Passive Infrared Technology (PIR)• Ultrasonic Motion Detection(OSC20-MSW)• Simple, Fast Installation• Ballasts, occupancy sensors, andcontrol stations connect on a sin-gle bus, topology-free, and polar-ity-free, two conductors• Compatible with Class 1 andClass 2 Wiring• Self-Adjusting• Digital Technology, CompleteReliability• Ceiling Mount• Non-Volatile Memory• Remote or Manual ConfigurationCapability• Adjustable Ambient Light ControlPassive Infrared Multi-Technologyproduct data FEaturES• Reduces Energy Costs: using the Sector Occupancy Sensors in a Leviton Sector Lighting Control System can reduce energy costs from 34% to 60%• Smart Settings: continuously analyze and adjust sensitivity, timer operation and long-term perfor-mance for a hassle-free lighting environment• Self-adjusting: continuously analyzing, learning and adapting to patterns of occupancy in a facility • Fast, Simple Installation: easy ceiling mount,2-wire connection (low voltage) and twist-lock sen-sor attachment• Topology-Free: ballasts, occupancy sensors, and control stations connect on a single bus, topology-free, and polarity-free, two conductors• Custom or Smart Delay-Off: manual (and self-adjusting) delay-off settings from 30 seconds to 30 minutes• Unobtrusive: small, tasteful unit blends in with any décor• Maximum Reliability, Minimum Cost: all digital circuitry uses a minimum of components• Flexible Installation: compatible with Class 1 and Class 2 wiring specifications, and Wiremold surface raceways for mounting to hard ceilings• Non-Volatile Memory: learned and adjusted settings saved in protected memory are not lost during power outages• Walk-Through Feature: increased energy savings by not leaving the lights ON for an extended period after only momentary occupancy• Ambient Light Control: includes Manual-ONand Always-ONFIELd-oF-VIEWSshown in this diagram*OCCUPANCY SENSORTo Additional Bus ControllersCan *PHOTOCELLClass 1Remote Control Circuit*SECTOR BALLASTBKG BR BR V GY RR Y BL Y BL *SECTOR BALLASTBKG BR BR V GY RR Y BL Y BL *SECTOR BALLASTBKG BR BR V GY RR Y BL Y BL *LOW VOLTAGE INTERFACE0-10V BALLAST CONTROLLERWH WH WH 24v DC Power Supply (optional)0-10V BALLASTLeviton Mfg. co., Inc. Lighting Management Systems20497 SW Teton Avenue, Tualatin, OR 97062 1-800-736-6682 Tech Line: 1-800-959-6004 Fax: 503-404-5594 /lms© 2009 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.S e c t o r o c c u p a n c y S e n s o r sproduct dataG-8113A/J9-cds REV OCT 2009Leviton Manufacturing co., Inc. Lighting Management Systems20497 SW Teton Avenue, Tualatin, OR 97062Telephone: 1-800-736-6682 • F AX: 503-404-5594 • Tech Line (6:00AM-4:00PM P .S.T. Monday-Friday): 1-800-959-6004Leviton Manufacturing of canada, Ltd.165 Hymus Boulevard, Pointe Claire, Quebec H9R 1E9 • Telephone: 1-800-469-7890 • F AX: 1-800-563-1853Leviton S. de r.L. de c.V.Lago Tana 43, Mexico DF, Mexico CP 11290 • Tel. (+52) 55-5082-1040 • F AX: (+52) 5386-1797 • .mxVisit our Website at: /lms© 2009 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.SpEcIFIcatIoNSElectrical• Input Voltage: 34-42VDC, 277VAC tolerant • Wires (2): Brown wires; polarity-freeEnvironmental• Operating temperature range: 32°F - 104°F (0°C - 40°C)• Relative humidity: Up to 95%, non-condensing • Usage: Indoors onlyPhysical• Size: 4.5” dia., 1.5” H (114mm, 38mm)• Weight: 5 oz. (142 g)• Housing construction: High-impact, injection molded plastic • Color: White• Leads: color coded, 6” (16.24cm)Listings• IEC61000-4-2Warranty• Limited 5-year warrantyThe following components are also part of the Leviton Sector Intelligent Lighting Control System:• Sector Ballasts (T8, 17W/25W/32W): SD1F8-17M, SD1F8-25M, SD1F8-32M, SD1J8-17M, SD1J8-25M, SD1J8-32M, SD2F8-17M, SD2F8-25M, SD2F8-32M, SD2J8-17M, SD2J8-25M, SD2J8-32M • Sector Bus Controller/Power Supply: SBP00-00M • Sector Photocell: ODC0P-0SW• Sector 5-Button Digital Switch: SDS00-15W • Sector Handheld Remote: SHH00-000• SectorNET Software and USB-to-LumaCan Adapter: SLM00-000, SIF00-000, SIFPD-000• Sector Ballast Controller: SBCS0-000, SBCS0-001• Sector 4-Module Enclosure (to hold a maximum of 4 Bus Controllers (SBP00-000)): SEN04-000。

智能照明标准管理系统方案智能照明管理系统建设方案深圳乙方照明科技有限公司二〇一五年十一月目录一、概述......................................... 错误！未定义书签。

二、方案总体设计................................. 错误！未定义书签。

系统设计思想及原则 ............................ 错误！未定义书签。

设计思想 .............................. 错误！未定义书签。

设计原则 .............................. 错误！未定义书签。

系统结构...................................... 错误！未定义书签。

系统优点概述 .......................... 错误！未定义书签。

系统结构图 (6)系统主要功能 (6)系统基本功能组成 ...................... 错误！未定义书签。

三、系统实现方式与技术指标....................... 错误！未定义书签。

3. 1监控中心................................... 错误！未定义书签。

....................................... 错误！未定义书签。

....................................... 错误！未定义书签。

....................................... 错误！未定义书签。

（RTU）........................................ 错误！未定义书签。

标准及规范 ............................ 错误！未定义书签。

....................................... 错误！未定义书签。

智能照明控制器原理
智能照明控制器是一种通过智能化技术实现灯光控制的设备。

它能够感知环境的光照条件，并根据预设的场景需求进行自动调节，提高能源利用效率和用户舒适度。

智能照明控制器的工作原理主要包括感知、处理和控制三个步骤：
1. 感知：智能照明控制器通过内置的光照传感器感知环境的光照条件。

传感器可以实时测量环境的亮度值，以及其他相关参数，如色温和颜色。

这些感知数据为后续的处理提供了基础。

2. 处理：智能照明控制器内部嵌入了先进的处理器和算法，它能够根据感知到的环境情况对灯光进行智能化的处理。

通过与预设的场景需求进行比对和计算，控制器能够确定最佳的灯光亮度、色温等参数。

同时，它还可以根据场景的变化和用户的需求进行动态调整。

3. 控制：一旦智能照明控制器完成了灯光参数的计算和处理，它会将控制指令发送给灯光系统。

这些指令可以是开关灯、调节亮度、改变色温等等。

通过与灯光系统的连接，智能照明控制器能够实现对灯光的精准控制。

此外，智能照明控制器通常还具有其他智能化功能，如时间调度、远程控制和与其他智能设备的联动。

这些功能使得智能照明控制器更加智能，提高了系统的整体性能和便利性。

智能照明控制器使用说明一、安装与设置1.将智能照明控制器固定在合适的位置，保证其稳定性和安全性。

2.连接所需的电源线，并确保电源供应正常。

3.根据实际需求选择需要连接的灯具类型，并将灯具与控制器进行连接。

4.将传感器与控制器进行连接，并根据安装环境调整传感器的灵敏度和工作范围。

二、基本功能1.手动控制：通过手动开关或遥控器控制灯具的开关和亮度调节。

2.自动控制：根据传感器所感知到的环境情况，自动调节灯具的开关和亮度，实现智能化的照明控制。

3.定时控制：设定灯具的开灯和关灯时间，实现定时开关，节省能源。

三、传感器应用1.光照传感器：根据环境光照强度的变化，自动调节灯具的亮度。

可以根据需要，设定光照阈值来控制灯具的开关。

2.人体红外传感器：通过感知人体移动来自动开启或关闭灯具，提高能源利用效率，并为用户提供便利。

3.温度传感器：根据环境温度的变化，自动调节灯具的亮度和颜色，提供舒适的光照环境。

4.湿度传感器：根据环境湿度的变化，自动调节灯具的亮度和颜色，提供适合人体的舒适光照。

四、智能算法1.自适应亮度调节：根据环境光照和人体活动情况，自动调节灯具的亮度，提供合适的光照。

2.节能模式：根据环境光照强度和人体活动情况，智能控制灯具的开关和亮度，实现节能环保的照明效果。

3.睡眠模式：根据用户设定的睡眠时间，自动调节灯具的颜色和亮度，提供舒适的光照环境，帮助用户入睡。

4.联动控制：通过智能连接其他家居设备，实现与窗帘、空调等设备的联动控制，提供更便捷的生活体验。

五、注意事项1.保持控制器的清洁和干燥，避免水和灰尘等杂质进入设备，防止损坏。

2.定期检查控制器的工作状态，如发现异常应及时处理或更换。

3.根据实际需要和环境情况，调整控制器的参数，以获得最佳的照明效果和节能效果。

总结：。