GP 的打印功能

GP无线WIFI打印机安装使用手册GP无线WIFI打印机参数功能介绍：可用Web 浏览器进行参数设定。

支持点对点(TCP、UDP) 和broadcast (仅UDP)。

支持WLAN 基础网（Infra）、自组网（Ad-Hoc）。

支持WLAN 安全(WEP64、WEP128、WPA-Personal、WPA2-Personal、TKIP、AES)。

内置AP、Ad-Hoc 搜索功能(site survey 功能)。

支持2.4G 无线网络（1-13信道可选）IEEE802.11b（11Mbps），IEEE802.11g（54Mbps），IEEE802.11n（72Mbps）。

接收信号强度大于-35db（72Mbps）。

支持AP（Access Point）路由和STA（Station）两种模式，用户可以通过网页选择不同模式。

AP模式：笔记本，手机，平板等无线终端可以直接搜索并连接到打印机。

STA模式：此模式打印机可以直接连接到路由器（可实现无线打印机共享打印功能）GP无线WIFI打印机使用设置步骤：一．AP（Access Point）模式设置方法1.请将纸卷放置打印机内部并开启打印机电源，使用可以接收无线WIFI的笔记本电脑设置电脑IP为自动获取状态。

2.搜索当前无线网络，查找到“Printer”打印机设备，点击“连接”连接到打印机。

3.我的电脑-》控制面板-》打印机和传真，找到已经安装好GP-80160II打印机驱动程序，右击选择“属性”。

4.选择“端口”，然后点击“添加端口”。

5. 选择“Standard TCP/IP Port”，并点击“新端口”。

6. 输入打印机默认IP地址，并点击下一步。

7.点击“常规”，然后点击“打印测试页”完成打印机安装,如果打印机能打印出测试页，表示已经可以正常使用。

二．STA（Station）模式设置方法1. 在AP模式下使用笔记本连接到打印机，如下图：2. 在IE浏览器输入：http://192.168.0.1，进入后输入用户名：admin，用户密码：admin 登陆到设置页面。

GP-H80250系列USB接口打印机安装及使用说明打印机USB使用介绍：打印机USB接口总体来说可分为真正的USB接口、并口转USB接口、串口转USB接口和USB虚拟串口等5种。

真正的USB接口和并口转USB接口：数据传输速度和打印速度都有保障，但应用软件接入联接打印不能直接兼容传统上的并口或串口；串口转USB接口：虽然说应用软件接入联接打印可以直接兼容传统上的串口，但数据传输速度和打印速度都是传统的串口速度，数据传输速度和打印速度都很慢，无法体现出打印机高速高效的特性；USB虚拟串口：既能够直接兼容传统上的串口，又能实现真正的USB接口的高速的数据传输和高速打印。

USB虚拟串口可以说是USB接口设计的最佳应用方案，盛源票据打印机公司出品的GP-H80250系列打印机正是采用了这种先进的技术，既采用USB接口与计算机相联接，又可以对应用软件的良好的兼容传统的串口，使应用软件只要支持串口打印，应用软件不须要做任何修改，就可以使用GP-H80250系列打印机的USB端口通讯轻松实现票据打印。

GP-H80250系列打印机USB驱动安装及使用说明：当计算机通过USB接口连接GP-H80250时，计算机即提示找到新硬件，如下图所示。

然后选择“从列表或指定位置安装（高级）（S）”，如下图所示。

然后选择“下一步（N）”，出现如下窗口所示，选择GP-H80250打印机USB端口驱动所在路经。

然后选择“下一步（N）”继续安装USB端口驱动。

当弹出如下所示窗口。

选择“仍然继续(C)”，即提示驱动安装“完成”，然后选择“完成”确认，如下图所示。

然后在“控制面版”——>“系统”——>“硬件”——>“设备管理器”——>“端口（COM和LPT）”——>“Gprinter Micro USB serial port (COM3)”，通过这里可以查看到打印机打USB虚拟的端口号，如COM3，这样打印机时，应用软件或是驱动里的通迅端口就要选择这个端口号，如COM3。

User's Manual GP-9025T/9026TThermal Transfer Barcode PrinterCustomer service hotline : 400 611 3828CONTENTSThe printerOptional accessoriesThe paper sizeProduct introductionAppearanceInternalThe bottomInstallationLED indicator functionTroubleshootingMaintenanceInstallation of paperButton FunctionCommon problem1313 6.1.Printer Cleaning1515The printerIntroductionThanks for choosing GP-9025T, GP-9026T series direct thermal and thermal transfer label printer.This series printer is built with 2 sets of gear to drive motor, with capability of handling 300meters long ribbon and large label roll. Printer inner volume is fit for 5" OD (Outer Diameter) paper roll, if using external paper holder, you can install 8.4"OD industrial grade label roll.This printer is designed for real-time and batch label printing, with standard serial, parallel, USB and Ethernet connection port. Direct thermal printing and thermal transfer printing modes are all in one printer body, so you can choose various kinds of printing materials, for example: thermal paper, plain paper, coated paper, silver paper, plastic paper etc.Common 1D barcode and 2D barcode fonts are built inside printer, also it support 4 direction printing, characters can be enlarged from 1 to 10 times. Besides, it supports 5 different size bitmap fonts, OCR-A and OCR-B fonts, together with 203dpi higher print resolution, this series printer are your best choice among the same class.Declaration : This is a class A product , fit for Non Tropic regions installation . This product may cause radio interference in life environment , users may need to take adequate preven -tive measures.Application FieldManufacturing & Warehousing logistic industryHealthcareParcel PostOffice & Studio RetailProduct labeling and marking Warehouse management label Category marking labelOperation instruction marking label Distributing instruction marking labelPatients marking Medicine marking Specimen markingMailing labelPrice Label marking Product item marking Jewelry product markingProduct featuresOptional accessoriesSpecificationsExternal support optional GP-9025T, GP-9026T standard.Print specificationsThe paper sizeProduct introductionOpen and checkThis series printer is with special package to prevent damage in transportation. If there is any unexpected damage occurred, please put in clean and stable surface and carefully open the package to check, inform local distributor with damage details, and keep packing mate -rials well in case you need to mail the printer.Packing list:◆ One Label printer◆ CD ( Driver, Nice label software, User Manual )◆ Power Adapter◆ Power Cord◆ USB cable ( Parallel cable, serial cable optional)◆ Ribbon roller & Ribbon◆ Label roller & Label paper◆ External paper holder (Standard for GP-9026T)<Picture 1>Please pack equipment and materials needed for safekeeping printer for subsequent handling; if the above items, any lost or missing, please Customer Service Department of your purchase contact.Printer componentsAppearanceLED lights indicate:★ ON LINE electric lamp ★ ERROR error lamp ★ RIBBON ribbon status light<Picture 2><Picture 3>Internal<Picture 5> The bottomNote: Picture showing printer port is for GP-9026T.InstallationInstall the printer1. Please put the printer on the stable surface.2. Make sure printer power is turned off, please do not plug the power cable when the printer power is turned on.3. Connect serial or USB or Parallel or Ethernet cable to printer and PC.4. Connect power plug to power supply socket.Be careful:※※ Transmission interface in the picture will vary depending on your printerpurchased aircraft type, the actual transmission interface, please refer tothe corresponding product specificationspower line is inserted into the printer.<Picture 6>Ribbon installation1. Press two press buttons on left and right side to open printer top cover.2. Put empty paper tube into ribbon take-up hub if you buy new ribbon which one side is no contact with paper tube.After that, install ribbon take-up hub left side and right side onto printer.Remark: Factory standard ribbon two sides already fixed well on paper tube. Go ahead to step 3 instead of step 2.3. Press the Push button to open print head.Ribbon installation diagram<Picture 7> Installation of paperInstallation of paper1.Open printer top cover;Insert blue label supply hub into label rolland fix onto printer.2.Press Push button to open print head toinstall label paper same as pictureshowing.4.Close printer top cover.3.Close the print head by pressing two arrowlocations. Confirm print head two sides areclosed correctly to ensure you get printingin good quality.LED Indicator and FunctionThere’re two buttons and three LED indicators, many functions can be realized through using different button, indicator and power on/off switch.LED indicatorDirect thermal printing methodLED Indicator status DescriptionsPower indicator is on，Error indicator is off Printer is powered on and in normal printing statusPower indicator flashes every 640ms,Error indicator is off Printer is pausedPower indicator is off, Error indicator goes for 80ms, then goes off for 160ms, printer start beeping.※on Printer cover is openedPower indicator is off for 500ms, then goes off for 6s , Error indicator goes on Label gap detection errorPower indicator is off Error indicator flashes every 160ms, after two times flashing, Error indicator goes off for 320ms, printer start beeping. ※, Paper outPower indicator is off Error indicator flashes every 160ms,after three times flashing,Error indicator goes off for 320ms, printer start beeping. ※, Black mark detection errorError indicator flashes every160ms.Printer overheated protection mode is act-ivated. After 1 minute, the printer CPU will check print head temperature again. When temperature return normal, printer will work normally.※ Beeper function can be enabled through setting DIP switch.※ Beeper function can be enabled through setting DIP switch.Thermal transfer printingLED Indicator status DescriptionRibbon indicator is on Ribbon is installed successfullyRibbon indicator flashes every 300ms, beeper sounds every 2.4s ※Ribbon improperly installed: no ribbon, or ribbon end, or ribbon brokenButton FunctionFeedWhen the printer is ready (LED blue fixed), click the button, label paper into the front end of a paper label. Print job timeoutThe printer in the print, click the PAUSE button to print suspended. At this time power indicator is blue flashing. Just click the button, the print job resume normal.Start functionThe printer has six kinds of power function can be used to set or test the printer hardware. In the boot and press the button with lamp signal release key can start these functions.Six Power-up Functions:Skip AUTO.BAS program User can use TSPL2command to save a code auto--ing file (AUTO.BAS)into flash. When turn on printer, prin-ter will run the program automatically. runnIf you want to skip AUO.BAS program on power-up, then follow below steps:Press and hold PAUSE and FEED button, then turn on theprinter. When Power indicator (blue) is off and Error indi -cator(red)is on, release PAUSE and FEED button, printerwill skip running AUTO.BAS program, and then Power indicator will be on.Printer Initialization A.Turn off the printer.B.Press and hold PAUSE and FEED button, then turn on theprinter. When Power indicator(blue)is on and Error indi-cator (red) is off, release PAUSE and FEED button, all data in printer DRAM will be cleared and printer setting will be restored to factory default setting. Then power indicator will be on and printer goes to ready status.* Factory default settings do not include ribbon setting.Ribbon Detection When printer power turn on, or it is in thermal transferprinting mode, printer will automatically detect ribbonstatus, to check if ribbon installed, or ribbon end, or work normally. After ribbon detecting, printer will be set tothermal transfer printing mode or direct thermal printing mode. If no ribbon,system will go to direct thermal printing mode and close ribbon rolling motor function.The printer configuration after the initialization will revert to the default values are as follows:Parameter Default settingSpeed Density Gap Direction 4inch/sec (101.6mm/sec), 203dpi100mmONONOFFOFFONONCLEARNOT CLEARTop left corner from printing direction Printing content are placed on page from top to bottomReference SHIFT OFFSET SET TEAR SET HEAD(Cover open detect)Set PRINTKEY SET REPRINT SET KEY1(FEED)SET KEY2(PAUSE) CLEAR RAMCLEAR FLASHProblems Possible Reasons Solution and Suggestion Power indicatornot "ON”TroubleshootingCommon problemBelow the table of contents is generally the common problems and solutions; if you have been in our proposed methods of eliminating the fault, and the printer is not normal operation, so check with your purchase customer service department, so as to get more help.Plug to AC outlet and plug toprinter not well connectedCheck power connector and AC outlsetif plugs are correctly connectedPrinter power not turned on Turn on power switchPrint head not well closed Close print head by pressing whole printhead mechanism (or 2 arrow locations)Ribbon endLabel paper jamed inside printerChange new ribbonRibbon improperly installed Refer to Ribbon Installation steps in UserManual to re-install ribbonLabel paper end Change new label paperLabel paper improperly installed Refer to Paper Installation steps in UserManual to re-install paperGap sensor detection error Adjust paper specification and print againClear jamed paperNot printingSerial cable improperlyconnected1. Check if Pin configuration in cable twosides are matching each other;2. Check if baud rate setting on PC andprinter are the same, If in TPSL comma-nd mode, We suggest 9600, n, 8, 1 toensure higher reliability.3. Change a new cable.Ethernet cable improperlyconnected1.Check if RJ-45 green/orange LEDindicator is on. When printer receiveand process printing data, LED will beorange color;2.Check if printer IP is assigned inDHCP mode.3.Check if fixed IP address is correctlyset in printer property. Wait for someminutes to make sure printer is connect-ed server and printing a selftest pageto confirm printer IP address.4.Change a new ethernet cable.USB cable improperlyconnectedCheck if USB cable connected well orchange a new cableRibbon non standard Check if ribbon model andspecificationNot printing Ribbon printing side wrong installed Check and re-install ribbon to make sure printing side touch label paperPrint head not clean Clean print head and print againPrint density setting wrong Suggest density set to be 7Print head cable not well connected Re-connect print head cableStep Motor cable not well connected Re-connect step motor cableCommand setting wrong Check if there is PRINT command at the end of printing file; or if there is CRLF command at the end of every line.Not goodprinting quality Ribbon and label improperly installed Too much dust or adhesive on print head Re-install ribbon and/or labelClean print head and print againPrint head damaged Take selftest page to check if printing are completely to confirm if necessary to change new print headData miss printing in one or two sides Label paper size wrong setting Check if label size set correctly and same as your label paperRibbon wrinkle Printing not stable Printer in HEX Dump mode or RS-232 setting wrong Print head unbalanced stress;ribbon & label improperly installed; Label feeding not smoothly Reset the label print density andadjust paper width fixing stand tofit your label paper size.Restart your printer and leave Dump Mode or reset RS-232 PARAMETERMaintenance6.6.1.Printer CleaningTo ensure the printing quality, please proceed this maintenance section to keep your printer in good conditions and extend its life as well.Please use one of following material to clean the printer.★ Cotton swab★ Lint-free cloth★ Vacuum / Blower brush★ 100% ethanol2.The cleaning process is described as following：Note：※Always turn off the printer power before cleaning the printer.※ Do not touch print head by figure.※ Please use 100% ethanol, Do not use medical alcohol to aviod damage to print head.。

蜂巢终端GP-80160小票据打印机设置方法1.蜂巢终端80160IN小票据打印机打印完成后总有一些内容在撕纸刀下方，撕的时候有些内容会留在下方？答：80160IN这款打印机是没有带切刀功能的，需要在安装驱动时选择GP-80160(No Cut)型号，此驱动就会自动把撕纸刀片以下的内容继续走出直到撕纸刀口对准所有打印内容之后的空白处。

2.蜂巢终端160系列小票据打印机机器串口打印很慢，怎么设置能实现快速打印？答：串口通信一般用于发送指令，如果使用驱动选择串口发送数据打印的话就会很慢，有两种方法，一是调整打印机波特率，把机器底部拨位开关8号键拨到ON的位置，机器波特率就变成了115200，电脑对应修改波特率，然后再打印，就会快一点；二是换用并口或USB口接口卡，能避免串口慢的问题。

3.蜂巢终端160系列小票据打印机，怎么正确选择端口？答：首先确认机器使用的数据线是何类型，如果是串口则在驱动的端口里选择COM1，如果是并口则选择LPT1，注意并口和串口是独占式端口，如果任何一个程序或者驱动占用了端口的话其他的任何程序和驱动都不能使用此端口，如果是USB口则选择USB001，注意USB口是系统虚拟端口，如果安装多台USB口打印机则会对应USB001，USB002，USB003….等等端口，需要用户一一对应确认。

然后观察系统内对应的驱动图标的状态是脱机还是准备就绪，如果是脱机则必须让驱动切换为准备就绪的状态。

接着在驱动的属性内打印一张测试页，如果出单子就证明驱动已经跟打印机通信好了，后续再用自己的软件打印就可以了。

4.蜂巢终端160系列小票据打印机，打印端口正确设置？答：这个时候要考虑硬件方面的问题：a)并口，并口不存在其他参数的调整，单子一直在任务栏里而且打印机没动作的话考虑是线材或者接口卡有问题。

b)串口，串口有通信速率也就是波特率的调整，如果波特率没对应上的话有可能是打印不出单子的，确认了波特率之后仍不行考虑线材或者接口卡有问题。

打印机操作步骤
一、装纸
1.按黄色按钮打开打印机盖，如图：
2.将纸装入打印机，纸从蓝色卡子底部出来，将右边卡子向左推动到合适位置稳住价格签，
如图：
3.打印纸露出打印机口1-2公分左右为准，如图：
4.装好打印纸，盖上盖子，按走纸按钮走一张纸之后再开始打印，如图：
注意：如打印机长时间不用或打印严重错位，请按照如上步骤重新装纸！！
二、海典正式版软件打印操作
第一种：
1.登录各门店店长海典账号
2.价格管理→打印价格签→添加→直接输入商品编码或者商品名称
（可以输入多个商品）→点打印预览按钮→选择打印机，见图2；（型号：GP-3100TU）→然后点打印按钮即可打印(注意打印方案是否为价格签）
如图：
第二种：
1. 库存管理→库存报表→查询→选择条件→业务机构→单品机构汇总数量→按功能主治→类别→确定
如图所示：
3.在查出药品中间位置点鼠标右键→选择所有→再在商品编码位置点鼠标右键→行拷贝
4.价格管理→打印价格签→添加→在商品编码位置点鼠标右键→行粘
贴→返回到第一行删除第一行空白，见图1：（备注：如不删除软件将强制关闭）
→点打印预览按钮→选择打印机，见图2：（型号：GP-3100TU）→此时页数较多需分页打印，见图3；→分页完成直接点打印(注意打印方案是否为价格签，如图4）
图1：
图2：
图3：
图4：。

GP条码打印机软件安装及使用说明运行如下图：点击“安装NiceLabel产品”安装条码机软件选择安装软件使用语言点击下一步点击下一步，查看许可协议。

接受协议并继续下一步自行调整安装路径和附加图标，并点击安装，等待安装过程完成点击完成运行软件，至此安装过程全部完成。

软件运行后点击介绍界面的继续进入欢迎向导软件提供了三个不同大小和内容的标签样式供参考，用户可以参照示例来进行编辑，下面介绍新建标签的步骤，选择“创建新标签”，然后点击完成标签设置向导中第一步定义标签的尺寸，如40 mm X 30 mm就在“标签宽度”里输入4，“标签高度”里输入3，可以根据需要调整度量单位，尺寸输入时自行转换，点击下一步打印机选择中软件会扫描驱动列表并筛选出GP系列驱动供使用，其余驱动会自动屏蔽，可以选择打印方向为纵向或横向，点击完成，进入软件编辑界面左侧工具栏中可以选择使用所有可编辑对象，如“文本”，“条码”，“图片”，“矩形”，“直线”，“椭圆”，“反白”点击“文本”，鼠标出现大写“A”字母后点击标签编辑界面中想放置的位置，出现文本向导，选择固定文本则可以在下方输入框内输入需要的文字内容，字体可以点击“选择”来改动，如下图：确认改动后点击完成则字体会出现在刚才点击的位置菜单栏中的文本一栏可以继续调整字体样式和大小若文本选择“变量文字”时，确认好字体样式后点击下一步这里有两个方式选择，“键盘输入”是在向打印机下发打印任务时软件会给客户一个相应提示，在此文本内打印什么字符由用户通过键盘输入，而不是固定文本。

“计数器”则可以使用软件的累加功能达到让数字累加的效果键盘输入向导需要填写提示文本，比如要提示输入“产品名”则在文本内写入“产品名”，可以设置“最大字符数”和“格式”“字首”“字尾”可以根据需要填写，也可不填，完成后在标签编辑界面会出现“？？？？？”的字样，在点击“打印”后会新增可以输入的文本框，并可以勾选“清除变量”，如下图：计数器方式的设置，点击下一步在这里可以设置“起始值”，如果勾选了“打印前提示数值”则可以像键盘输入文本一样在打印时输入初始值，“设置最大位数”表示数字最多的位数，可以选择“递增”或者“递减”方式，“预览”一栏可以看到数值变化的效果，点击下一步“每隔”填入每次递增或者递减的数量，“每几张标签更改一次值”填入每一个数值需要重复的标签数量，“到达极限值时重新计数”一栏可以勾选后输入一个极限值，每次到达极限值就会循环重新计数，更改好参数后可以从“预览”中看到数字是如何变化的，下一步中的字首字尾跟键盘输入的一致，完成后在标签界面同样会出现“？？？？？”的字样，点击打印并打印多张就可以看到实际的效果了点击左侧“条码”，鼠标会变成带有条码标示的形状，点击标签编辑界面中需要放置的位置，出现条码向导。

佳博GP-80250VN热敏票据打印机
佳博GP-80250VN热敏票据打印机是由中国知名的票据打印机生产商珠海佳博科技股份有限公司生产。

佳博GP-80250VN热敏票据打印机由250毫米/秒高速打印机支持前出纸带切刀支持条码打印。

120毫米的大纸卷支持43mm、58mm、70mm、80mm、82mm多种纸宽。

它同时支持串口、USB、以太网接口。

佳博GP-80250VN热敏票据打印机可选EPSON ESC\POS和STAR两种指令模式菜单及错误报警功能，及时提醒用户有单打印支持网络状态监控、电脑多联接打印。

它支持高级OPOS驱动打印机身份验证、电脑软件绑定驱动高速下载打印模式。

佳博GP-80250VN热敏票据打印机支持GB18030大字库和多种国际语言。

欢迎各位商家光临采购，联系人：陈小姐，电话：4006113828。

新版GP 以太网（Ethernet）端口打印机使用及配置说明注：本说明只适用于WinNT、Win2k、WinXP和Win2003操作系统。

1、安装并运行以太网接口打印机测试及配置程序GPEthernet .exe，如下图所示。

2、通过打印机开机自检测条查看打印机网络IP address及Ethernet ID。

3、修改PC主机IP地址使PC主机IP地址与打印机网络IP地址在同一网关，如打印机IP地址为192.168.123.100，则可修必PC主机IP地址为192.168.123.200。

4、在打印机测试及配置程序“Printer current IP address”后的文本框中输入打印旧的IP address，如打印机开机自检测条上“IP address”为“192.168.123.100”则输入“192.168.123.100”，通过打印机测试及配置程序GPEthernet.exe执行“Connect Test”，如通讯成功，则显示如下图所示窗口。

5、在打印机测试及配置程序“Printer set new IP address”后的文本框中输入打印机的新IPaddress，如要将打印机的“IP address”修改为“192.168.123.200”则输入“192.168.123.200”。

然后执行“Set New IP Address”，这样打印机的IP地址被修改，通过打印机开机自检测条可查看打印机的IP address。

注意：网络中PC主机及网络接口打印机IP 地址不能重复。

6、在打印机测试及配置程序“Set New Ethernet ID”的文本框中输入打印机的新Ethernet ID，如要将打印机的“Ethernet ID”修改为“0-201-202-203-204-205”则输入“0-201-202-203-204-205”。

然后执行“Set New Ethernet ID”，这样打印机的Ethernet ID被修改，通过打印机开机自检测条可查看打印机的Ethernet ID。