机械词汇翻译

机械设计专业术语的英语翻译阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD912不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit913齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector914当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch915端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy916分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line917公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design918。

机械专业英文翻译 Company number：【WTUT-WT88Y-W8BBGB-BWYTT-19998】启动轴 starting axle 启动齿轮starting gear启动棘轮 starting ratchet wheel 复位弹簧 restoring, pull back spring弹簧座 spring seating 摩擦簧friction spring推力垫圈 thrust washer 轴挡圈axle bumper ring下料 filling 切断 cut 滚齿机 gear-hobbing machine剪料机 material-shearingmachine车床 lathe 拉床broaching machine垂直度 verticality, verticalextent 平行度 parallelism同心度 homocentricity位置度 position拉伤 pulling damage碰伤 bumping damage缺陷 deficiency严重缺陷 severe deficiency摩擦力 friction 扭距 twist滑动 glide 滚动 roll打滑 skid 脱不开 can’t seperate不复位 can’t restore 直径 diameterM值 = 跨棒距 test rod span公法线 common normal line 弹性elasticity频率特性 frequency characteristic误差 error响应 response 定位 allocation 机床夹具 jig 动力学 dynamic运动学 kinematic静力学 static分析力学 analyse mechanics拉伸 pulling压缩 hitting机床 machine tool刀具 cutter摩擦 friction联结 link传动 drive/transmission轴 shaft剪切 shear扭转 twist弯曲应力 bending stress三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation电路 circuit半导体元件 semiconductor element拉孔 broaching装配 assembling加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration稳定性 stability介质 medium液压驱动泵 fluid clutch 液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability机械制图Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams反馈 feedback发生器 generator直流电源 DC electrical source 门电路 gate circuit外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向 directionof resultant movement of cutting 切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe镗削 bore集成电路 integrate circuit挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion 冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器Programmable LogicController PLC毛坯 rough桁架 truss轴线 axes逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构fluid drive mechanism机械零件 mechanical parts产品突出特点ProductHighlights特别优惠 special offersAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skrpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块barreling 滚光加工 belling 压凸加工bending 弯曲加工 blanking 下料加工bulging 撑压加工 burring 冲缘加工cam die bending 凸轮弯曲加工caulking 合加工coining 压印加工 compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工 dinking 切断蕊骨double shearing 叠板裁断 drawing 引伸加工drawing with ironing 抽引光滑加工 embossing 浮花压制加工extrusion 挤制加工 filing 锉削加工fine blanking 精密下料加工 finish blanking 光制下料加工finishing 精整加工 flanging 凸缘加工folding 折边弯曲加工 folding 摺叠加工forming 成形加工 impact extrusion 冲击挤压加工indenting 压痕加工 ironing 引缩加工knurling 滚花 lock seaming 固定接合louvering 百叶窗板加工 marking 刻印加工necking 颈缩加工 notching 冲口加工parting 分断加工 piercing 冲孔加工progressive bending 连续弯曲加工 progressiveblanking 连续下料加工progressive drawing 连续引伸加工 progressiveforming 连续成形加工reaming 铰孔加工 restriking 二次精冲加工riveting 接加工 roll bending 滚筒弯曲加工roll finishing 滚压加工 rolling 压延加工roughing 粗加工 scrapless machining 无废料加工seaming 折弯重叠加工 shaving 缺口修整加工shearing 切断加工 sizing 精压加工/矫正加工slitting 割缝加工 spinning 卷边接staking 固 stamping 锻压加工swaging 挤锻压加工 trimming 整缘加工upsetting 锻粗加工 wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴 blank determination 胚料展开bottom slide press 下传动式压力机 board drophammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包 casting on flat 合chamotte sand 烧磨砂 charging hopper 加料漏斗clearance 间隙 closed-die forging 合模锻造clump 夹紧 clutch 离合器clutch brake 离合器制动器 clutch boss 离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置 coil reel stand 钢材卷料架column 圆柱 connection screw 连杆调节螺钉core compound 砂心黏结剂 counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless 无曲柄式 cross crank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 die approach 模口角度die assembly 合模 die cushion 模具缓冲垫die height 冲压闭合高度 die life 模具寿命die opening 母模逃孔 die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床 draght angle 逃料倾斜角edging 边锻伸 embedded core 加装砂心feed length 送料长度 feed level 送料高度filling core 埋入砂心 filling in 填砂film play 液面花纹 fine blanking press 精密下料冲床forging roll 辊锻机 finishing slag 炼後熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床 formboard 进模口板frame 床身机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹口剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置 hammer 槌机hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床 hopper feed 料斗送料idle stage 空站 inching 微调尺寸isothermal forging 恒温锻造 key clutch 键槽离合器knockout 脱模装置 knuckle mechanic 转向机构land 模具直线刀面部 level 水平loader 供料器 unloader 卸料机loop controller 闭回路控制器 lower die 下模micro inching device 微寸动装置 microinching equipment 微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机 opening 排料逃孔overload protection device 防超载装置 pinch roll 导正滚轮pinion 小齿轮 pitch 节距pressfit 压入 progressive 连续送料pusher feed 推杆式送料 pusher feeder 料片押片装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversedblanking 反转下料robot 机器人 roll formingmachine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料 roller leveler辊式矫直机rotary bender 卷弯成形机 safetyguard 安全保护装置scrap cutter 废料切刀 scrap press废料冲床seamless forging 无缝锻造separate 分离shave 崩砂 shear angle 剪角sheet loader 薄板装料机 shot 单行程工作shrinkage fit 收缩配合 shutheight 闭合高度sieve mesh 筛孔 sintering of sand铸砂烧贴slide balancer 滑动平衡器 slughole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程 take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机 vibration feeder振动送料机wiring press 嵌线卷边机业务与贸易关连用语accept order 接受订货 account 帐户after service 售后服务 amendment 修正annual sales 年销售额 at sight 见票即付balance 余额 bank draft 汇票bargain goods 廉价品 batch 批次bid 出价 bid sales 投标买卖bill of landing 提单 bills receivable 应收票据brand 品牌 bulk cargo 散装货business transaction 商业交易 buyer 买方carbon copy 打字副本 cargo collection 揽货carton 纸箱 cash in advance 预付现金catalogue 型录 cheque 支票CLF 运费保险费在内价格 claim 索赔clearance goods 清仓品 commision 佣金commission 批发商 complain 抱怨container 货柜 correspondence bank 往来银行cost 成本 cost and freight; C&F 含运费价格custom broker 报关行 customer 客户D/A 承兑交单 D/P 付款交单deferred payment 分期付款 deferred shipment 分期装运delivery on spot 当场交货 delivery time 交期delivery order 交货单 discount 折扣discount on draft 贴现 documentary draft 跟单汇票down payment 订金 enclosure 附件endorsement 背书 enquete 调查exhibition 展览会 export 出口factory visiy 工厂参观 favourable price 合宜价格foreign exchange 外汇 free on board 船上交货价idea price 希望价格 import 进口Japanese Industrial 日本工业规格 invoice 发票L/C 信用状 margin 利润market 市价 net weight 净重no payment 拒绝付款 odd item 零头offer 报价 open account 交互计算order 订单 over looked 疏漏packing 包装 pamphlet 小册子partial shipment 分批装船 patent 专利paying price 合算价格 payment method 付款方式port of destination 目地港 port of trans-shipment转口港price 价格 price decending 减价price rising 涨价 procurement 采办prompt delivery 即时交货 purchase 购入purchasing agent 采购代理商 quotation 报价单rebate 回扣 reference 查询remittance 汇款 repeat order 追加订货request letter 请求函 rumor 风评second hand goods 二手货 shipper 货主shipping 装船 shipping mark 麦头shipment 出货 sold out 卖完sole agent 总代理商 special discount 特别折扣specification 规格 sample order 指样订货standing 信用情形 storage charge 仓租subcontract 外包 subject to final confirmation 有待确认之报价supplier 供应商 T/T 电汇tie-in sale 搭售 trade fair 商展会trans-shipment 转运 transferred 已转运wharf 码头。

机械专业英语词汇ﻫ陶瓷ceｒaｍｉｃsﻫ合成纤维synthｅtic fibreﻫ电化学腐蚀ｅleｃｔroｃｈemicａｌcoｒrｏｓion车架automotivｅcｈassis悬架sｕspeｎsion转向器rｅdｉｒectoｒ变速器spｅｅｄｃhangｅrﻫ板料冲压sheet metal paｒｔsﻫ孔加工ｓｐot facinｇmachｉninｇ车间ｗorkｓhop工程技术人员engineｅrﻫ气动夹紧pnｅｕma lｏcｋﻫ数学模型matｈematicａl mｏdｅｌﻫ画法几何descｒiptｉveｇｅｏmｅｔｒyﻫ机械制图Ｍechａnical drａwiｎg投影proｊｅｃtｉonﻫ视图view剖视图pｒo标准件sｔａndard ｐoｎentﻫ零件图part ｄrawing装配图assemｂｌｙdraｗiｎg尺寸标注ｓｉzｅmarkingﻫ技术要求technｉcal requｉrementsﻫ刚度rigiｄityﻫ内力internal forceﻫ位移dｉｓｐlaｃｅｍeｎｔ截面ｓectiｏn疲劳极限ｆaｔiguｅlimit ﻫ断裂frａｃｔureﻫ塑性变形pｌａsｔic ｄistortioｎﻫ脆性材料bｒittlｅness maｔerｉａlﻫ刚度准则riｇiｄiｔｙcriｔeriｏnﻫ垫圈ｗasher垫片sｐacｅrﻫ直齿圆柱齿轮sｔraｉｇｈｔtｏoｔhｅｄspur gｅarﻫ斜齿圆柱齿轮ｈｅliｃal—ｓpur geａrﻫ直齿锥齿轮strai ｇｈｔｂevｅｌgeaｒ运动简图kｉnemａｔic sketchﻫ齿轮齿条piniｏn and raｃkﻫ蜗杆蜗轮ｗｏrm and ｗorm ｇear虚约束paｓsivｅｃoｎstraｉｎｔ曲柄cｒank摇杆ｒａcｋeｒﻫ凸轮camｓﻫ共轭曲线cｏnjｕｇａｔｅｃuｒveﻫ范成法generation mｅｔｈod ﻫ定义域definitionａl doｍain值域rangｅﻫ导数\\微分differentiａｌcoeffiｃientﻫ求导derｉｖatiｏn ﻫ定积分deｆinite iｎtｅgraｌ不定积分indｅfinite inｔegrａl曲率curvａtuｒｅﻫ偏微分partｉal differentｉalﻫ毛坯rｏuｇh游标卡尺sliｄe ｃaｌiｐｅrﻫ千分尺micrｏmｅter calipers ﻫ攻丝tap二阶行列式sｅcond ｏｒdｅr ｄeｔerminanｔﻫ逆矩阵invｅｒse matriｘ线性方程组lｉneaｒequaｔiｏnｓ概率ｐｒｏｂａbility随机变量randoｍvariabｌeﻫ排列组合permｕtaｔion ａnd binatiｏnﻫ气体状态方程equａtion of state oｆgａs 动能kiｎetiｃenergyﻫ势能potential energｙ机械能守恒consｅrvatiｏｎof mｅchanical energyﻫ动量mｏmeｎtuｍ桁架trussﻫ轴线ａxeｓ余子式cofaｃtorﻫ逻辑电路lｏgic cｉrｃｕｉｔ触发器ｆlｉp—ｆloｐﻫ脉冲波形pｕlse ｓｈape数模diｇital ａnalogy ﻫ液压传动机构fluid dｒｉｖe mechaniｓm机械零件mechａnｉcaｌpaｒts淬火冷却qｕｅnchﻫ淬火hａrdeｎｉngﻫ回火teｍpｅriｎg调质ｈａｒdeninｇand ｔemperｉｎg ﻫ磨粒abrasiｖｅgraiｎﻫ结合剂boｎdingａgent砂轮ｇrindiｎg wｈeｅl后角cｌearａｎｃe aｎgｌｅﻫ龙门刨削plａnｉng主轴spｉndｌe主轴箱headstock卡盘ｃhｕｃkﻫ加工中心mａchｉniｎg cｅntｅr车刀latｈe tool车床ｌatheﻫ钻削镗削bｏreﻫ车削ｔurｎing磨床grinder基准benchｍaｒkﻫ钳工locksｍithﻫ锻forｇeﻫ压模ｓtampｉng焊welｄ拉床broachｉng machine拉孔bｒoaching装配asｓemｂling铸造ｆoｕｎdﻫ流体动力学fluid dynamiｃs流体力学fluiｄmechaniｃs加工machinｉｎgﻫ液压ｈyｄraulic prｅssｕre切线tangent机电一体化mecｈanotronｉｃs mechaｎical—eｌectriｃaｌｉｎteｇraｔionﻫ气压ａir pｒessｕre pｎeumａtic pｒｅsｓuｒe 稳定性stabiｌitｙ介质ｍediｕｍﻫ液压驱动泵fluid cluｔch液压泵hydraｕlｉc puｍpﻫ阀门vａlｖe失效iｎvaｌiｄａtioｎ强度intenｓｉtｙﻫ载荷ｌoadﻫ应力sｔｒｅss安全系数safty faｃｔorﻫ可靠性ｒeliａbility螺纹ｔhｒead螺旋ｈｅlixﻫ键splｉnｅﻫ销ｐinﻫ滚动轴承rolliｎg beariｎg滑动轴承slidinｇbeaｒｉｎg弹簧spriｎgﻫ制动器arreｓtｅr braｋeﻫ十字结联轴节crosｓheａdﻫ联轴器coｕpｌingﻫ链cｈａinﻫ皮带ｓtrapﻫ精加工ｆｉnisｈmachiningﻫ粗加工rough machinｉｎｇﻫ变速箱体gearｂｏx casinｇﻫ腐蚀rustﻫ氧化oxｉｄatiｏnﻫ磨损wear 耐用度dｕrabilｉty随机信号ｒaｎdom signalﻫ离散信号disｃrｅte sｉｇnaｌﻫ超声传感器ultｒaｓoｎｉcｓｅnsorﻫ集成电路intｅgrate cirｃuit 挡板oｒｉfｉcｅplａteﻫ残余应力resｉdｕal stresｓ套筒ｓｌeeve ﻫ扭力torsｉｏnﻫ冷加工colｄmａchｉniｎg电动机eｌecｔroｍｏtorﻫ汽缸cyliｎdｅr过盈配合iｎtｅrfeｒｅnｃe fiｔ热加工ｈotwｏrk摄像头CCD camｅrａ倒角rｏundｉng cｈamfｅｒ优化设计optimal dｅｓignﻫ工业造型设计industｒial moｕlding design有限元fiｎitｅelemｅntﻫ滚齿hobbｉng插齿ｇeａr shａｐingﻫ伺服电机actuaｔiｎg moｔorﻫ铣床milling ｍaｃhine钻床drｉll machine镗床ｂoring ｍachine步进电机steｐpeｒｍotorﻫ丝杠sｃreｗrodﻫ导轨lead rail组件sｕbassemblyﻫ可编程序逻辑控制器Prｏｇrａｍmable LogｉｃControlｌer PLC电火花加工eｌeｃtriｃspａrｋmachｉｎinｇﻫ电火花线切割加工ｅlectrical disｃhａrgｅwiｒe - ｃuttingﻫ相图phase diａｇram 热处理hｅat tｒeatmentﻫ固态相变solid statｅphａｓe changｅs有色金属noｎferrous mｅtalﻫ陶瓷cerａmicsﻫ合成纤维syntｈetｉc fibre电化学腐蚀ｅｌectrochemical corrｏsiｏｎ车架aｕtomotive ｃｈaｓｓisﻫ悬架ｓuspｅnsiｏnﻫ转向器ｒedｉｒeｃtoｒ变速器sｐｅｅd cｈanger板料冲压sheｅt ｍetaｌｐａrtｓﻫ孔加工sｐot facｉng machiｎiｎgﻫ车间worｋshop工程技术人员eｎgｉneｅrﻫ气动夹紧pneuma loｃk数学模型mathemａｔical modelﻫ画法几何ｄescｒiptｉvｅgeometry机械制图Ｍｅchanical draｗiｎg投影ｐrojｅction视图viｅｗ剖视图prｏ标准件standard ｐoｎｅｎｔﻫ零件图part dｒawinｇ装配图assemｂlｙdrａwｉng尺寸标注ｓize mａrkinｇﻫ技术要求teｃhｎｉｃａｌrｅｑuiｒｅmeｎts刚度rigidiｔｙﻫ内力internal fｏrｃｅ位移displaｃement截面sｅcｔiｏn疲劳极限fａtiｇue limiｔﻫ断裂fraｃtuｒeﻫ塑性变形plａstic distorｔion脆性材料brｉｔtleness materiaｌﻫ刚度准则rigidity cｒiterion垫圈ｗａｓｈerﻫ垫片ｓpacer直齿圆柱齿轮sｔrａight toｏｔhed spur gｅaｒ斜齿圆柱齿轮heｌicaｌ-spur gearﻫ直齿锥齿轮ｓtｒａｉgｈt ｂeveｌｇeａr ﻫ运动简图kｉnemａｔｉｃskｅtｃhﻫ齿轮齿条pinioｎａnd rack蜗杆蜗轮ｗorm and ｗorm geａr虚约束pａsｓivｅconstraintﻫ曲柄ｃrank摇杆rａcｋer凸轮cams共轭曲线cｏｎjuｇaｔe ｃurveﻫ范成法ｇeｎeratｉon ｍethｏd ﻫ定义域deｆiniｔiｏｎaｌdｏmａin值域range导数＼\微分differeｎtial coefｆｉｃienｔﻫ求导ｄeriｖａtion ﻫ定积分definite intｅgrａl不定积分ｉnｄefinｉte inｔegral曲率ｃuｒvature偏微分partiａl diffｅrentiａl毛坯ｒoｕgｈﻫ游标卡尺ｓlide caliperﻫ千分尺mｉcromeｔer calｉｐers ﻫ攻丝tａp二阶行列式sｅcond oｒder determinａnt逆矩阵invｅrse matｒｉx线性方程组linｅar eｑｕatiｏｎs概率probabｉlｉtｙ随机变量raｎｄｏｍｖariａbleﻫ排列组合permｕtatｉon ａnｄｂiｎatｉon气体状态方程eｑuａｔion ｏfｓtate oｆgaｓ动能kineｔic ｅneｒgy势能pｏtｅnｔial enｅrgｙ机械能守恒ｃoｎservatiｏn of ｍechanｉcal energyﻫ动量momenｔumﻫ桁架tｒussﻫ轴线axｅsﻫ余子式cofaｃｔoｒ逻辑电路logic circｕｉtﻫ触发器fｌｉp—flop脉冲波形ｐuｌｓe sｈaｐｅ数模ｄigital ａnalｏgy ﻫ液压传动机构flｕid drｉｖe mechaｎism机械零件mechａnical partsﻫ淬火冷却quenｃｈﻫ淬火hａrdeｎinｇﻫ回火tempeｒｉｎg调质hａrdｅning ａnｄtｅmｐering磨粒abｒasｉｖｅｇｒaiｎﻫ结合剂bonding aｇeｎt砂轮ｇrinding wheelAssｅmｂly line 组装线Ｌａｙout 布置图ﻫCoｎvｅyeｒ流水线物料板ﻫＲivｅｔtaｂle 拉钉机ﻫRivｅｔguｎ拉钉枪Scｒeｗdriver 起子Pneuｍａｔic scrｅｗdｒiver 气动起子woｒkｔａble工作桌ﻫOＯＢA开箱检查fit togeｔｈer组装在一起fａｓtｅn锁紧(螺丝）ﻫｆixture 夹具(治具)ｐaｌlet 栈板barｃｏｄe 条码baｒｃoｄe sｃaｎneｒ条码扫描器ｆusｅtogeｔher 熔合fuse mａcｈinｅ热熔机ﻫrepaiｒ修理ｏperatｏｒ作业员ﻫＱC品管ﻫsuｐerviｓor课长MＥ制造工程师MT制造生技ｃoｓmｅｔicｉｎsｐeｃt 外观检查ﻫinｎer ｐａrts insｐect内部检查ｔｈumb scｒew大头螺丝lbs、iｎch 镑、英寸EMI gａsket 导电条ﻫfront ｐlate 前板ﻫreａr plate后板ﻫｃhassiｓ基座bezel paneｌ面板ﻫpｏｗｅr buｔtoｎ电源按键reseｔｂuttｏn 重置键ﻫHi-potｔest of SＰＳ高源高压测试ﻫVoltagｅsｗitch oｆSＰS 电源电压接拉键ﻫｓhｅet metal pａrtｓ冲件plaｓtic ｐartｓ塑胶件ﻫSOP制造作业程序ﻫmaterial check list 物料检查表ﻫｗorｋcell 工作间trollｅy 台车ｃartoｎ纸箱ﻫsuｂ－liｎe 支线lefｔfoｒk 叉车peｒｓonnel rｅｓource department 人力资源部pｒｏduction ｄｅpaｒtｍenｔ生产部门ﻫpｌanning department企划部ＱC Sｅctｉoｎ品管科ﻫｓtampiｎg fａｃtory冲压厂ﻫpａiｎｔiｎg fａcｔory烤漆厂moｌding factoｒｙ成型厂ﻫｍon eｑｕipｍent常用设备uｎcoｉleｒａｎd stｒaightｅnｅr整平机ﻫpuｎching machiｎe 冲床rｏboｔ机械手ﻫｈydrａulic ｍaｃhiｎe油压机ﻫlａｔhｅ车床ｐlaner |plｅｉn｜刨床ﻫmiｌlｅr铣床grinｄeｒ磨床liｎear cutｔing线切割ｅlectｒical sparkle电火花welｄeｒ电焊机ﻫstａker=ｒevitingｍachiｎe铆合机positiｏｎ职务ﻫpresidｅnt董事长ﻫgｅnｅral ｍanａgｅr总经理ﻫspecial aｓsｉsｔａnt manaｇer特助factｏrｙdirector厂长depaｒtmeｎt direｃtｏr部长deputy mａｎager |=viｃe manaｇer副理seｃtion supervisoｒ课长dｅputyｓecｔiｏn sｕｐervｉsｏr ＝vice sｅctｉon superisoｒ副课长ﻫｇｒoｕp leａdeｒ/ｓｕｐeｒvisｏｒ组长line ｓｕpｅrvisｏｒ线长aｓｓisｔanｔmanａｇer助理toｍｏve, to caｒrｙ, tｏｈandle搬运ﻫbｅput ｉn storａｇe入库pack packing包装ｔo ａｐｐｌｙoｉl擦油ﻫto锉毛刺ﻫfiｎalｉnspｅcｔiｏｎ终检tｏcoｎnect materｉaｌ接料to rｅversｅmatｅriaｌ翻料wet ｓtａｔioｎ沾湿台Tiaｎa天那水cleanｉｎg cloｔh抹布ﻫto load ｍateｒｉａl上料ﻫｔo unｌoad ｍateｒiaｌ卸料ﻫｔo rｅｔurｎmateriａｌ/stoｃk to退料ﻫscｒap ｅd |\\'skr?ｐid|报废ﻫｓcrape 、、v、刮;削ﻫdeficiｅnｔpurcｈase来料不良mａnｕfａcturｅproceduｒe制程deficｉent mａｎufactuｒing procedure制程不良ﻫoxidａｔioｎ｜＼＼' ksi\＼’dｅｉ？n｜氧化ﻫscratcｈ刮伤ﻫdents压痕ｄeｆeｃtivｅupsidｉng dｏｗn抽芽不良defeｃｔive to staｋiｎg铆合不良eｍｂedｄｅd lumｐ镶块ﻫfeediｎg is not in place送料不到位stａmping－mｉssing漏冲pｒodｕction cａｐａcity生产力educａtｉon anｄtraining教育与训练ｐropｏsａｌimprovｅmeｎt提案改善ﻫｓｐａre parts=bｕｆfeｒ备件ﻫfoｒklｉft叉车ﻫtrａiler=ｌong ｖｅhicｌe拖板车pound ｄie合模ﻫdie lockｅr锁模器pressure plate=ｐlate pｉncｈ压板ﻫbolt螺栓adminisｔｒation/geｎerａl ａffairs dept总务部automaｔｉcｓcrewdrｉｖer电动启子thｉckｎesｓgａuge厚薄规ｇaugｅ(oｒjｉg)治具ﻫpowｅr wirｅ电源线ﻫbｕzzｌe蜂鸣器ｄｅfeｃtiveｐroｄuct labｅｌ不良标签ﻫidentifyiｎｇｓheｅt lisｔ标示单ﻫlocatｉon地点prｅseｎt meｍｂers出席人员ｓubject主题ﻫcoｎcｌuｓiｏｎ结论ﻫdｅcｉsion iｔeｍs决议事项ﻫｒespｏnsible departmeｎt负责单位pｒe－ｆixed ｆinishiｎg date预定完成日ﻫapproｖeｄｂy / checked ｂy / prepared by核准/审核/承办ﻫPCE assｅｍbly proｄｕction sｃhedulｅｓhｅet PCE组装厂生产排配表modｅl机锺ﻫwoｒk order工令ﻫrevision版次ﻫｒemark备注pｒoductiｏnｃｏntrol conｆirmaｔion生产确认ﻫchecked by初审ﻫapｐroved bｙ核准ﻫdｅpartment部门ﻫsｔｏck aｇe analｙsiｓｓｈeet 库存货龄分析表ﻫon—hand inventｏｒy现有库存ﻫavaｉlable materiaｌ良品可使用ｏｂsoletｅｍaterial良品已呆滞to bｅｉnspecteｄor ｒｅworkeｄ待验或重工tｏtal合计ﻫcause descripｔioｎ原因说明ﻫpaｒt nｕｍber／P／N 料号ﻫｔype形态iteｍ/group／clａss类别qｕality品质pｒｅpaｒｅｄbｙ制表nｏtes说明ｙｅaｒ-enｄｐhyｓical ｉnvｅntory differenｃe aｎaｌｙｓis sheｅt 年终盘点差异分析表ﻫphysicａl invｅnｔｏry盘点数量ﻫpｈysicaｌcou ｎt quaｎtｉty帐面数量diｆfｅrｅnce ｑｕantｉty差异量ﻫcausｅaｎalysis原因分析rａｗmａｔerials原料matｅrials物料ﻫｆiｎiｓｈｅｄprｏdｕcｔ成品ﻫsemi—fｉnished proｄｕcｔ半成品packiｎg mateｒｉａlｓ包材ﻫgooｄprodｕct／ａcceｐｔeｄgoodｓ/ accｅpted pａrts/ｇｏod parｔs良品dｅfecｔive produｃt／non－goodｐaｒtｓ不良品disｐoｓeｄｇoｏds处理品ﻫwarehoｕse/hub仓库ﻫon ｗay loｃａtion在途仓overseａloｃation海外仓ﻫsparｅｐａrts phｙsical invｅntorｙliｓt备品盘点清单ｓpare moｌds location模具备品仓ﻫｓｋｉｄ/pａｌlet栈板tｏｘmachine自铆机wire EDM线割ﻫＥDM放电机ﻫcoil ｓtocｋ卷料ｓｈeｅt sｔocｋ片料toｌerancｅ工差ﻫscorｅ＝ｇrooｖe压线ﻫｃaｍblocｋ滑块ｐｉlot导正筒tｒim剪外边ﻫpiｅrｃe剪内边dｒａg form压锻差ﻫpocｋet fｏr the ｐuncｈhｅad挂钩槽slug ｈｏle废料孔ﻫｆｅaｔｕre ｄｉｅ公母模eｘpansｉｏn dwg展开图ｒaｄiｕｓ半径ｓhｉm(weｄge）楔子tｏrcｈ－flame cut火焰切割set scｒew止付螺丝ｆorm blocｋ折刀stop ｐin定位销rｏunｄpｉerceｐuｎch＝ｄｉe button圆冲子shape ｐｕｎch=diｅｉnsｅrt异形子sｔock locater bｌoｃk定位块ﻫｕｎdｅr cｕt＝scｒａpｃｈoｐpｅｒ清角ﻫａctｉｖe plate活动板bａffｌe plaｔe挡块cover plａte盖板ﻫmalｅｄie公模ﻫｆemａｌe ｄie母模ｇrｏove puncｈ压线冲子air—cｕsｈioｎｅjｅcｔ—rod气垫顶杆spｒiｎg—bｏｘejｅct－pｌaｔｅ弹簧箱顶板ﻫbusｈiｎg bloｃｋ衬套ﻫｉnsｅrt 入块ﻫclub car高尔夫球车ﻫcaｐaｂiｌｉtｙ能力ﻫｐarame ｔer参数ﻫfaｃｔor系数ﻫphosphaｔｅ皮膜化成ﻫｖisｃosiｔy涂料粘度alkaliｄipping脱脂ﻫmaiｎmａnifold主集流脉ﻫbezel斜视规blankｉｎｇ穿落模ﻫｄeｊectinｇ顶固模demagnｅtizａｔioｎ去磁;消磁ﻫhｉgh-ｓｐeｅdｔｒａnｓmisｓion高速传递ｈｅat dｉｓsｉｐａtｉon热传rａck上料dｅgrｅaｓe脱脂ﻫｒinse水洗alkalinｅｅtch龄咬ﻫdｅｓｍｕｔ剥黑膜D、Ｉ、ｒｉnsｅ纯水次ﻫCｈromaｔe铬酸处理Ａｎｏdiｚe阳性处理ﻫseal封孔reｖiｓｉon版次ﻫpart ｎumbｅr／Ｐ/Ｎ料号good proｄucts良品ｓcraped producｔs报放心品defｅctive ｐroｄuｃｔs不良品ﻫfinishｅdｐrｏｄuctｓ成品ｄispoｓｅd ｐｒoｄｕcｔs处理品bａrcodｅ条码ﻫｆloｗｃhａrt流程表单assembｌy组装ﻫsｔaｍping冲压molding成型ﻫsparｅpartｓ=buffer备品ﻫｃoordinａte座标dismantｌｅｔhe die折模auxｉliaｒy fuｃtion辅助功能poｌｙ-line多义线ｈeater band加热片thermocouｐｌe热电偶saｎd ｂｌasting喷沙ﻫｇriｔ砂砾ﻫｄerusｔing ｍachine除锈机ﻫdeｇaｔe打浇口ｄryer烘干机ﻫｉnduｃtion感应ﻫiｎｄuｃtion ｌight感应光ﻫresponsｅ=rｅaction=ｉnterａctｉon感应rａｍ连杆eｄge fiｎder巡边器ﻫconｃave凸cｏnvex凹ﻫsｈort射料不足nicｋ缺口ｓｐeck瑕疵sｈine亮班ｓpｌay 银纹ﻫｇaｓmark焦痕ﻫdelamｉnａtion起鳞ﻫｃoｌd slｕg冷块bｌush 导色ﻫgougｅ沟槽;凿槽ﻫsatin ｔeｘtｕre段面咬花witｎesｓline证示线ﻫpaｔｅnt专利ﻫｇrit沙砾ﻫgｒaｎuｌe=pｅｕet=grain细粒ﻫgrit ｍaｋer抽粒机cushｉｏｎ缓冲magnalｉｕm镁铝合金ｍaｇnｅsｉｕm镁金mｅtal plaｔe钣金ﻫlａthｅ车miｌl锉ﻫpｌaｎe刨ｇｒinｄ磨ﻫdrilｌ铝boｒiｎg镗blinsｔer气泡ﻫfｉllet镶;嵌边throｕgh－hｏｌe forｍ通孔形式ｖollｅｒｐｉn formalｉtｙ滚针形式ﻫcam drｉvｅr铡楔ﻫshａnk摸柄ｃraｎk ｓｈaft曲柄轴auｇuｌar oｆfset角度偏差ﻫvｅｌｏcｉty速度pｒoduｃtｉｏｎｔｅmｐo生产进度现状ｔｏrqｕe扭矩spline=the multiｐlｅｋeys花键ﻫquenching淬火ﻫtｅmpｅring回火ﻫannealinｇ退火ﻫcarbonｉｚatiｏｎ碳化ﻫtungsｔeｎhigh sｐｅeｄｓteel钨高速得ﻫｍoly high speed steel钼高速得ﻫorganic solvｅnt有机溶剂ﻫbraｃket小磁导ｌｉaiｓｏn联络单ﻫvｏlatiｌｅ挥发性ﻫｒeｓｉｓｔａnce电阻ion离子ﻫtitrａｔor滴定仪ﻫｂeaｃon警示灯coolanｔ冷却液cｒｕsher破碎机阿基米德蜗杆Aｒｃhｉmedeｓwｏrmﻫ安全系数ｓａfeｔyｆactor；factor of sａｆｅtyﻫ安全载荷safe load凹面、凹度ｃoncavｉｔyﻫ扳手ｗreｎch ﻫ板簧flａtｌeaf sｐring半圆键wooｄｒuff keｙﻫ变形defｏrmａtionﻫ摆杆oscillaｔiｎg baｒ摆动从动件osｃillatｉng followｅrﻫ摆动从动件凸轮机构cam with oscillatinｇfollower摆动导杆机构osｃｉlｌatｉng guide—ｂａr mｅchaniｓｍﻫ摆线齿轮cycloidal geａr摆线齿形cｙｃloiｄａｌtooth profile摆线运动规律ｃycloｉdal motion摆线针轮cycloｉdal-pｉn wheelﻫ包角angｌｅof conｔａctﻫ保持架cageﻫ背对背安装back—to－ｂaｃk aｒｒangｅmｅntﻫ背锥ｂack ｃone；normal ｃｏｎeﻫ背锥角bａck angｌeﻫ背锥距ｂack cｏnｅｄistａnceﻫ比例尺ｓｃaleﻫ比热容ｓpｅcｉｆｉcｈｅat caｐacｉty闭式链closed kinｅmaticｃhａiｎﻫ闭链机构ｃlosｅd chain mｅｃhａnism臂部ａrm变频器frequenｃy convｅrtersﻫ变频调速freｑueｎcy cｏnｔrol ｏｆmotoｒspｅed变速sｐｅｅｄchangeﻫ变速齿轮chanｇe geａr ｃｈanｇeｗheeｌﻫ变位齿轮modｉfieｄｇearﻫ变位系数ｍodｉficationｃoeｆficieｎtﻫ标准齿轮standard geａｒ标准直齿轮standaｒd spuｒｇｅａr表面质量系数superficial mass facｔoｒﻫ表面传热系数surfaｃe coefficｉeｎt oｆｈｅat tｒaｎsｆerﻫ表面粗糙度surfａｃｅroughneｓsﻫ并联式组合binatiｏn in pａrａllel并联机构paraｌlel mechaｎisｍﻫ并联组合机构parallel bined mｅchａnismﻫ并行工程conｃurrent ｅngｉneeringﻫ并行设计ｃｏnｃurｒｅd deｓigｎ，ＣＤ不平衡相位phase aｎgle oｆｕnbalance不平衡ｉmbalance (or unbalａｎce）ﻫ不平衡量amoｕnｔof uｎｂalanceﻫ不完全齿轮机构intｅrmittent gearｉng波发生器ｗａvｅgenｅrator波数numbｅr of wａvｅsﻫ补偿pensａtion参数化设计ｐarａmetｅｒizaｔioｎdｅｓign，PDﻫ残余应力residual strｅｓsﻫ操纵及控制装置opｅrａtｉon coｎtrol ｄｅｖice槽轮Ｇeneｖa ｗheｅlﻫ槽轮机构Genｅvaｍecｈaｎisｍ；Maｌtesｅcｒossﻫ槽数Gｅnevaｎumｅrａte槽凸轮groove ｃamﻫ侧隙bａcklashﻫ差动轮系diｆｆerentｉal gearｔraiｎ差动螺旋机构ｄiffeｒeｎｔial scｒew mechanismﻫ差速器diffｅrential常用机构ｃｏnｖeｎtｉoｎal ｍｅchaｎiｓm；ｍecｈaｎｉsmｉn ｍon uｓｅ车床lａtｈeﻫ承载量系数ｂearing capacity ｆactｏrﻫ承载能力beariｎg ｃapａcity成对安装pａired moｕntinｇ尺寸系列ｄimeｎｓｉon sｅｒiesﻫ齿槽tooｔh space齿槽宽spacｅwiｄth齿侧间隙backlａshﻫ齿顶高ａｄdendｕm齿顶圆addendｕm ciｒｃle齿根高ｄｅdendum齿根圆dｅｄendｕm cｉrcleﻫ齿厚ｔooｔh thicknｅｓs齿距circｕlａr pitchﻫ齿宽faｃｅｗidｔh齿廓ｔooｔh profilｅ齿廓曲线ｔooth cｕrve齿轮geaｒﻫ齿轮变速箱spｅｅd—ｃhangiｎg geaｒboｘesﻫ齿轮齿条机构pinｉｏn anｄｒackﻫ齿轮插刀pｉnion ｃuｔter；pinｉoｎ－shａp ｅｄshaper cutter齿轮滚刀hob，hobbｉnｇcutterﻫ齿轮机构ｇｅarﻫ齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器geaｒcｏuplingﻫ齿条传动rａck ｇearﻫ齿数toothｎumｂer齿数比geaｒｒａｔｉo齿条ｒａｃk齿条插刀rack cutter；raｃk—shapeｄshapeｒｃutteｒ齿形链、无声链silenｔchain齿形系数foｒmｆaｃｔor齿式棘轮机构tｏoth ratchet mechａnism插齿机ｇｅａr sｈａｐerﻫ重合点coｉncident poiｎtsﻫ重合度contａｃt ratｉｏ冲床pｕncｈ传动比tｒaｎsmisｓｉoｎｒａtio，speeｄraｔｉｏ传动装置gearing；tranｓmissiｏn ｇear传动系统driｖen sｙstｅmﻫ传动角transｍiｓsｉon angｌe传动轴ｔransmｉssｉｏｎshａftﻫ串联式组合bｉnation iｎseｒｉesﻫ串联式组合机构seｒｉes binｅd mecｈanismﻫ串级调速casｃade speｅｄｃｏｎｔｒol创新inｎovatiｏn ｃrｅatiｏnﻫ创新设计crｅatｉon ｄeｓign垂直载荷、法向载荷normａｌloadﻫ唇形橡胶密封lip ruｂｂer seaｌﻫ磁流体轴承ｍagｎｅticｆｌuid bｅarｉｎg从动带轮dｒivｅｎｐulleｙ从动件ｄrｉvｅｎlink，folｌｏwｅｒﻫ从动件平底宽度widｔh oｆｆlａt－face从动件停歇ｆｏlloｗeｒdｗellﻫ从动件运动规律ｆolｌｏweｒmｏtionﻫ从动轮drivｅn gear粗线bold lｉneﻫ粗牙螺纹coarsｅｔhread大齿轮gear wｈｅｅlﻫ打包机paｃkｅr打滑slippingﻫ带传动belt ｄrｉvingﻫ带轮belt ｐullｅy带式制动器band brakeﻫ单列轴承sｉnｇle roｗbearｉng单向推力轴承siｎgle－dirｅcｔｉon thrｕsｔbeａring单万向联轴节singｌe ｕｎiveｒsal ｊｏint单位矢量unit vecｔｏr当量齿轮eｑｕｉvalｅｎt spｕrｇear；virtual gearﻫ当量齿数equivaｌeｎt tｅｅtｈnumber；viｒtuａｌnumｂeｒｏf teｅtｈ当量摩擦系数eｑuivalｅnt cｏeffiｃｉenｔof frictｉonﻫ当量载荷equiｖaｌent loaｄﻫ刀具ｃutｔerﻫ导数ｄerivative倒角chaｍｆｅrﻫ导热性conduｃｔｉonｏf hｅat导程leadﻫ导程角ｌead angleﻫ等加等减速运动规律ｐaraｂｏlic motion；cｏｎｓtaｎt accｅleｒation anｄｄeceleratｉon motionﻫ等速运动规律uｎifｏrm mｏtion；consｔanｔveloｃity ｍｏtiｏｎ等径凸轮ｃonjuｇaｔe yokｅradial camﻫ等宽凸轮coｎsｔaｎt-breａdth camﻫ等效构件equivaleｎt liｎkﻫ等效力equivａleｎt forceﻫ等效力矩eｑuｉvalenｔmｏment oｆfoｒｃｅ等效量ｅquiｖａleｎtﻫ等效质量ｅquivaｌent mａss等效转动惯量ｅquivａlenｔmoment oｆinertｉａ等效动力学模型dynａmicａｌlｙequｉvalenｔｍｏdelﻫ底座ｃｈassｉs低副lｏwer paｉr点划线chain dotｔedｌｉne（疲劳）点蚀pｉttingﻫ垫圈gaｓketﻫ垫片密封gasket sｅal碟形弹簧bｅlleville ｓpriｎgﻫ顶隙bottom cleａraｎceﻫ定轴轮系ordｉnarｙgear tｒaｉn；geａr trａｉn ｗith ｆｉxeｄaxeｓﻫ动力学dynamiｃsﻫ动密封kinｅmatiｃal sealﻫ动能dynamｉc ｅneｒgy动力粘度ｄynaｍｉc vｉｓcoｓity动力润滑dynamic lubricatiｏn动平衡ｄｙnamiｃbalanceﻫ动平衡机dyｎamiｃbａlaｎｃing mａｃhiｎe动态特性dｙnamic cｈaracteriｓticsﻫ动态分析设计ｄynamic anａｌysis design动压力dｙnamic reactｉoｎ动载荷dynamic load端面transverse pｌaｎe端面参数tranｓvｅｒse parametｅrsﻫ端面齿距tｒａnsverseｃirculａr ｐｉtchﻫ端面齿廓traｎsveｒse ｔooth prｏfｉleﻫ端面重合度traｎsverse contaｃt ratioﻫ端面模数transｖerse ｍｏｄuleﻫ端面压力角transvｅrse prｅｓsureａngle锻造foｒｇeﻫ对称循环应力ｓｙｍｍeｔrｙｃｉrculａtｉｎｇstrｅｓsﻫ对心滚子从动件raｄiａl （ｏr in-liｎｅ）rolｌeｒfｏlｌoweｒﻫ对心直动从动件rａｄial (or iｎ-lｉne ) ｔrａｎslaｔinｇfｏlｌｏwerﻫ对心移动从动件ｒａｄial reciprｏcaｔiｎg folｌｏweｒﻫ对心曲柄滑块机构in—linｅslｉder－crank(ｏｒcranｋ-sliｄer）mechａnismﻫ多列轴承mｕlti—row bearingﻫ多楔带ｐｏly V—ｂｅlｔ多项式运动规律polynomｉａl ｍｏｔｉｏｎﻫ多质量转子rotｏr wｉtｈｓevｅral ｍａsｓeｓﻫ惰轮idｌe gｅａr额定寿命rating life额定载荷loａｄratｉngII级杆组ｄyadﻫ发生线genｅratiｎg ｌine发生面generaｔiｎg planｅ法面nｏrｍalｐｌａne法面参数normal paramｅｔerｓﻫ法面齿距normal cirｃular ｐitch法面模数normal ｍｏｄule法面压力角ｎormal ｐｒeｓsure aｎgleﻫ法向齿距normal pitch法向齿廓noｒmａl tｏotｈprｏfileﻫ法向直廓蜗杆ｓtｒaiｇｈt sided normal wｏrｍﻫ法向力ｎｏrmal ｆorｃeﻫ反馈式组合feｅｄback bining 反向运动学invｅｒｓｅ（ｏr backwarｄ）ｋinｅmaｔicｓﻫ反转法ｋｉｎematic invｅrｓｉon反正切Arctanﻫ范成法gｅneratiｎｇｃｕtｔｉng仿形法form ｃｕtｔingﻫ方案设计、概念设计cｏncepｔdesign, ＣＤﻫ防振装置sｈockpｒoof devicｅﻫ飞轮fｌywｈeｅl飞轮矩momeｎｔof flywheel非标准齿轮nonstanｄardｇｅar非接触式密封non-contaｃt seaｌ非周期性速度波动aperiodiｃspeeｄfｌuctuatiｏｎﻫ非圆齿轮noｎ-circular gearﻫ粉末合金powdｅｒｍetalｌuｒgyﻫ分度线ｒeferｅnce line; staｎdaｒdｐitｃh lineﻫ分度圆refｅrｅnce cｉrｃle；ｓtandaｒd （cｕttiｎg)ｐitｃh circlｅ分度圆柱导程角lead aｎｇlｅaｔrｅferenｃｅcyｌinｄｅrﻫ分度圆柱螺旋角helix ａngle at reference ｃylｉｎderﻫ分母dｅnomiｎatｏrﻫ分子n ｕmeratorﻫ分度圆锥ｒeferenｃｅcone；standarｄpｉｔｃh coneﻫ分析法aｎａｌyｔicａｌｍｅtｈｏdﻫ封闭差动轮系ｐlａneｔarｙdiffｅrｅntｉalﻫ复合铰链pｏｕnｄhｉｎgeﻫ复合式组合pound biniｎg复合轮系pｏuｎd （ｏｒbineｄ) geａr train复合平带pound fｌａt belt复合应力bｉnｅｄｓｔｒeｓｓ复式螺旋机构pound screw mechａnism复杂机构pｌｅx mｅchaｎｉsmﻫ杆组Asｓｕr groｕｐ干涉inteｒferencｅﻫ刚度系数stiｆｆnｅss coｅfｆicｉent刚轮rigiｄcｉrculaｒｓpｌine钢丝软轴ｗiｒe ｓoft sｈａft刚体导引机构ｂodｙｇuiｄancｅmｅchaｎisｍ刚性冲击ｒigid imｐulse(shｏｃｋ）ﻫ刚性转子rigiｄrotoｒﻫ刚性轴承rigiｄbeariｎgﻫ刚性联轴器ｒiｇidｃouplingﻫ高度系列heigｈt series 高速带hｉgｈｓpｅed beltﻫ高副ｈiｇhｅr pair格拉晓夫定理Gｒashｏｆf｀s ｌaｗﻫ根切undercuttinｇﻫ公称直径nominal dｉameterﻫ高度系列heighｔsｅriesﻫ功woｒk工况系数aｐpｌｉcatｉｏn ｆａctorﻫ工艺设计tｅchｎologicａl desｉgｎﻫ工作循环图ｗoｒkｉng ｃｙcｌe ｄiaｇrａm工作机构ｏperation ｍｅchaniｓｍ工作载荷extｅrnal ｌoads工作空间workiｎg spａce工作应力woｒkingｓtｒｅss工作阻力ｅfｆectivｅｒesisｔａnce工作阻力矩ｅffeｃｔｉｖe reｓｉｓｔａnce moment公法线mｏn normaｌlineﻫ公共约束ｇeneral coｎstraintﻫ公制齿轮metｒic geａrsﻫ功率powｅｒﻫ功能分析设计fuｎｃtion aｎalyｓes desigｎﻫ共轭齿廓cｏｎｊugate proｆilesﻫ共轭凸轮ｃonjugaｔe cam构件liｎk鼓风机bｌoweｒﻫ固定构件fixed link；frａmｅﻫ固体润滑剂solｉd lｕbrｉcａnt关节型操作器jｏiｎted maｎｉpulator惯性力ineｒtia forcｅﻫ惯性力矩mｏmeｎｔｏf ｉnｅrtia ,ｓｈａkｉｎg momenｔﻫ惯性力平衡bａｌａｎce of shａkｉng ｆorｃeﻫ惯性力完全平衡full balanｃe of sｈaking foｒceﻫ惯性力部分平衡ｐａrtｉal balaｎｃｅｏｆshaking forceﻫ惯性主矩resuｌtant momenｔof ineｒtia惯性主失reｓultant vectｏｒｏf ｉnｅrtia冠轮cｒowｎgearﻫ广义机构genｅｒａｔｉoｎｍecｈanisｍﻫ广义坐标generａlized cooｒｄiｎaｔｅ轨迹生成ｐａth ｇeｎeration轨迹发生器paｔｈgeneｒatｏrﻫ滚刀hob滚道raceｗay滚动体rollｉng ｅｌeｍeｎt滚动轴承rolliｎg beａringﻫ滚动轴承代号ｒｏｌlｉng bearｉng ideｎtificａtioｎcode滚针ｎeｅdlｅｒoｌler滚针轴承ｎeedle roｌｌer beａrinｇﻫ滚子roｌlerﻫ滚子轴承roｌｌｅrｂearingﻫ滚子半径rａdius of ｒolleｒﻫ滚子从动件roller ｆollowｅr滚子链ｒｏｌlｅrｃhaｉnﻫ滚子链联轴器doublｅｒｏller chain couplingﻫ滚珠丝杆ｂalｌscｒewﻫ滚柱式单向超越离合器rｏller cｌutch过度切割underｃuttingﻫ函数发生器ｆunction ｇeneraｔｏr函数生成fｕnctiｏｎgenerａtion ﻫ含油轴承oiｌbｅarinｇﻫ耗油量oｉl consumptionﻫ耗油量系数oil consumｐtion fａｃtoｒ赫兹公式H、Heｒtz eqｕationﻫ合成弯矩ｒesｕltaｎt bendｉnｇｍoｍentﻫ合力ｒesuｌｔａnt fｏrｃe合力矩ｒｅｓultant ｍomeｎt ｏf forcｅﻫ黑箱blackｂｏｘﻫ横坐标absciｓsa互换性齿轮interｃｈangｅablｅgeａrs花键ｓpliｎeﻫ滑键、导键ｆｅaｔhｅｒｋey滑动轴承slidiｎg bｅaｒing滑动率slｉｄｉng ratioﻫ滑块sliderﻫ环面蜗杆toｒｏid helicoｉds worｍ环形弹簧annｕlar sｐrｉnｇ缓冲装置ｓhocks; sｈoｃk—absorbｅr灰铸铁gｒｅｙcａｓt iron回程ｒｅtｕｒn回转体平衡balａnｃe oｆrotors混合轮系ｐoundｇeａr train积分inｔｅgｒaｔｅ机电一体化系统设计mechanｉｃal-elecｔriｃａlｉｎtegratｉon system ｄeｓigｎ机构mechａniｓmﻫ机构分析aｎａｌysｉｓof meｃhaniｓm机构平衡balaｎcｅof meｃｈaｎismﻫ机构学ｍeｃhanisｍ机构运动设计kinematiｃｄesign of mechanｉsｍ机构运动简图ｋinｅｍａtic sketch of mechanｉｓmﻫ机构综合syｎｔhｅsis oｆmechanｉsm机构组成ｃonsｔitution of ｍｅcｈａnismﻫ机架frame,fiｘｅdｌink机架变换kinemａｔｉc inversiｏn机器machine机器人rｏbｏt机器人操作器mａniｐulａｔor机器人学robｏtiｃｓ技术过程ｔechniquｅprｏｃesｓ技术经济评价tecｈnical and economic evalｕaｔiｏnﻫ技术系统technique ｓystｅm机械mａcｈｉneryﻫ机械创新设计mechanicalｃreatioｎdesｉgn，ＭCＤﻫ机械系统设计mechaniｃal sysｔem ｄesigｎ, MSD机械动力分析ｄynａmic analyｓis oｆmａchinery机械动力设计dynamic dｅsigｎｏf mａcｈｉnｅｒyﻫ机械动力学dynaｍicｓof mａchinｅryﻫ机械得现代设计mｏｄerｎｍａchｉnｅdｅsｉgnﻫ机械系统meｃhａnｉcａl sｙｓtｅｍﻫ机械利益ｍechanical advaｎｔage机械平衡bａlaｎce of ｍachinｅｒyﻫ机械手mａnipulａtoｒ机械设计mａｃhinｅｄeｓiｇn；mecｈaniｃａｌdeｓｉgnﻫ机械特性mｅcｈanical bｅhavioｒ机械调速mｅchaｎiｃal sｐｅed gｏvｅrnors机械效率mecｈanｉcal efficieｎｃyﻫ机械原理ｔheｏry ofｍachiｎes anｄmechanismsﻫ机械运转不均匀系数ｃoefｆicｉent oｆｓpeed flｕctuａtｉon机械无级变速meｃhａniｃａl steplｅssｓpeed chaｎgeｓ基础机构ｆundamｅntal meｃｈａｎｉsｍﻫ基本额定寿命basic rａtinｇlｉfeﻫ基于实例设计cａse-baｓｅd deｓｉgn,CBD基圆base cｉrclｅﻫ基圆半径radius ｏf baｓe cｉrcｌｅ基圆齿距bａse pitｃh基圆压力角presｓｕrｅangle of bａse circlｅ基圆柱base ｃylinder基圆锥base cｏne急回机构quick－retｕrn ｍｅｃhanisｍ急回特性quick—retuｒn characｔeｒistiｃｓ急回系数advancｅ—tｏｒeｔurn-ｔiｍe ratｉo急回运动ｑuick—reｔuｒn mｏtion棘轮ratchｅｔ棘轮机构ratcheｔｍｅchaｎism棘爪pawｌﻫ极限位置extreme (or limiｔiｎg）poｓｉtｉonﻫ极位夹角crａnｋaｎｇlｅbeｔween extreme（or limiting）poｓitions计算机辅助设计putｅr aideｄdesign, ＣAＤ计算机辅助制造puter ａided manuｆａcturｉnｇ，ＣAMﻫ计算机集成制造系统puter iｎtegrａted manｕfacturing ｓystem，CIMSﻫ计算力矩fa ｃｔoｒed moment；calcuｌation moment计算弯矩caｌculａteｄbeｎding momｅnｔﻫ加权系数weigｈｔiｎgｅfficient加速度acｃeleration加速度分析accelｅrａtion analysisﻫ加速度曲线accｅleraｔionｄiａgｒam尖点pｏiｎtiｎg; cuspﻫ尖底从动件kniｆｅ—edge ｆoｌlｏwerﻫ间隙bacｋlash间歇运动机构intermittent mｏtｉｏn meｃhanｉsm减速比reducｔionｒatio减速齿轮、减速装置reｄuctionｇｅar减速器ｓpｅed rｅducｅrﻫ减摩性antｉ—friｃtｉoｎquaｌｉty渐开螺旋面ｉnvoｌｕｔeｈeｌiｃoidﻫ渐开线involｕtｅ渐开线齿廓invｏlｕte pｒoｆｉlｅﻫ渐开线齿轮invｏlute gear渐开线发生线geneｒaｔｉng liｎe ofｉnvolｕｔｅﻫ渐开线方程invｏlute equatiｏnﻫ渐开线函数invｏlｕｔｅfuｎctｉon渐开线蜗杆involuｔｅwoｒmﻫ渐开线压力角ｐrｅｓｓure aｎglｅof ｉnvoｌute渐开线花键involute spｌineﻫ简谐运动ｓimｐle haｒmonic motiｏnﻫ键key键槽keywａy交变应力reｐeatｅd strｅssﻫ交变载荷ｒｅpeaｔed fluctｕaｔing loadﻫ交叉带传动ｃross-belt drive交错轴斜齿轮cｒｏssed helicａｌgearsﻫ胶合ｓcｏrｉｎgﻫ角加速度ａngulaｒaccelerａｔionﻫ角速度ａngular vｅlociｔy角速比aｎｇulａr veloｃity ratio角接触球轴承aｎｇｕlar contact baｌl bｅaｒinｇ角接触推力轴承anguｌar contacｔｔhrust ｂeａringﻫ角接触向心轴承aｎgular coｎｔaｃt radｉal ｂearingﻫ角接触轴承angulａｒcｏnｔact bearing铰链、枢纽hingeﻫ校正平面corｒecｔingｐlanｅ接触应力coｎtact stｒesｓ接触式密封conｔact sｅal阶梯轴mｕltｉ—ｄｉaｍｅｔeｒsｈａftﻫ结构ｓtrｕcｔureﻫ结构设计ｓtruｃtuｒal dｅsign截面sｅｃtioｎ节点ｐitｃh ｐointﻫ节距circular piｔｃh；pitch oｆtｅethﻫ节线piｔｃh lineﻫ节圆pitcｈcirｃlｅﻫ节圆齿厚thｉcknｅss on piｔｃｈcircleﻫ节圆直径pitchｄｉametｅr节圆锥pitchｃoｎe节圆锥角pitｃh conｅangle解析设计analytｉｃａl desiｇn紧边ｔigｈt-sideﻫ紧固件fａstener径节diａｍeｔral piｔｃh径向ｒadiaｌdiｒectionﻫ径向当量动载荷dｙｎamic equｉvalenｔradial ｌoａd径向当量静载荷statｉc equｉvａlenｔrａdial loadﻫ径向基本额定动载荷basiｃdynamｉc radｉal loaｄｒaｔiｎｇﻫ径向基本额定静载荷ｂasic s ｔatic rａdiａl ｌｏad tatiｎg径向接触轴承ｒadｉal contａct bearｉng径向平面radiａｌplanｅﻫ径向游隙ｒａdial ｉｎtｅrnaｌclearanｃe径向载荷radｉal loadﻫ径向载荷系数rａdial loａdｆactor径向间隙clearaｎceﻫ静力stａtｉc ｆorｃｅ静平衡static balanceﻫ静载荷stａｔic lｏad静密封static sｅal局部自由度ｐasｓivｅdeｇree of frｅｅdｏｍﻫ矩阵matｒixﻫ矩形螺纹sqｕaｒe threadeｄfｏｒmﻫ锯齿形螺纹bｕｔtrｅsｓthｒead formﻫ矩形牙嵌式离合器ｓquaｒｅ－ｊａw positiｖe-ｃontacｔｃｌutch绝对尺寸系数aｂｓｏlｕte dimｅnｓioｎal factorﻫ绝对运动ａbｓoluｔe moｔｉｏn绝对速度absoluｔeｖeloｃitｙ均衡装置lｏad ｂａlanｃｉng mechanismﻫ抗压强度prｅsｓion sｔrength开口传动ｏpen—belt drｉvｅﻫ开式链oｐｅn kinematic chain开链机构opｅｎcｈａin mecｈanｉsｍ可靠度degｒee of ｒelｉaｂiliｔyﻫ可靠性ｒelｉａbility可靠性设计relｉability desigｎ，RＤﻫ空气弹簧air sｐｒｉngﻫ空间机构spaｔiａｌmeｃhanism空间连杆机构spaｔial ｌｉnkａｇeﻫ空间凸轮机构spａtial cａｍﻫ空间运动副spaｔial kｉnｅmatｉc pａiｒ空间运动链ｓpatiａl ｋｉneｍatiｃchａin空转ｉdleﻫ宽度系列width seriesﻫ框图ｂloｃk diaｇramﻫ雷诺方程Ｒeｙnolds‘ｓeqｕatｉｏn ﻫ离心力cｅntrifugaｌforce离心应力ｃeｎtｒｉfｕgalｓtrｅssﻫ离合器clｕtcｈﻫ离心密封ceｎtrｉfugal seａl理论廓线pitｃｈcurve理论啮合线tｈeorｅtｉｃaｌline ｏf actionﻫ隶属度ｍeｍbeｒsｈiｐ力fｏｒcｅﻫ力多边形foｒｃe ｐolygonﻫ力封闭型凸轮机构foｒce—ｄrｉve (oｒfoｒｃe－ｃlosｅd) cam meｃhanｉsｍﻫ力矩momeｎtﻫ力平衡eｑuilibrium力偶cｏｕplｅﻫ力偶矩moｍｅｎt of couｐleﻫ连杆conneｃtｉng rod，coｕplerﻫ连杆机构ｌinkaｇe连杆曲线coupler—cuｒve连心线lｉne oｆcenｔersﻫ链chａiｎﻫ链传动装置ｃhain ｇｅarｉngﻫ链轮sｐrockｅt ｓｐｒocket—ｗheel ｓpｒocｋｅｔgear ｃhaiｎwhe ｅｌ联组V带tｉgｈt－up Ｖbｅlt联轴器cｏｕｐlinｇsｈａft ｃoupｌingﻫ两维凸轮two－dｉmensioｎａｌcam临界转速crｉtical speed六杆机构ｓix-bar lｉnｋageﻫ龙门刨床ｄoubleＨaaｓｐlaneｒ轮坯blanｋ轮系ｇear ｔraｉｎﻫ螺杆scrｅw螺距thrｅaｄｐｉtｃｈﻫ螺母ｓｃrewｎuｔ螺旋锥齿轮hｅlical bevel gearﻫ螺钉ｓｃrews螺栓bｏltsﻫ螺纹导程leaｄﻫ螺纹效率scｒeｗeｆficieｎｃyﻫ螺旋传动pｏwer ｓcreｗﻫ螺旋密封spｉrａl seａlﻫ螺纹ｔｈreａd (of a scｒew)ﻫ螺旋副helicaｌpair螺旋机构ｓｃrｅw meｃhanismﻫ螺旋角heｌixａngle螺旋线ｈelｉx ，hｅliｃaｌlineﻫ绿色设计ｇreeｎdeｓigｎdesign for enviroｎmｅntﻫ马耳她机构Ｇeｎevａwheel Geneva gearﻫ马耳她十字Malteｓｅｃｒｏss ﻫ脉动无级变速ｐｕlsａｔiｎg steｐlesｓsｐeed cｈanｇeｓ脉动循环应力flｕctuａtingｃircｕlａtｉｎg stｒess脉动载荷flｕcｔuａtｉｎg load铆钉rivet迷宫密封labyrinth ｓｅaｌﻫ密封ｓeal密封带sｅal ｂeｌtﻫ密封胶seal ｇumﻫ密封元件ｐotted ponｅntﻫ密封装置ｓeaｌｉｎg aｒraｎgemｅｎｔﻫ面对面安装faｃe—to-faｃe ａrr ａngeｍent面向产品生命周期设计ｄesigｎｆor ｐｒoducｔ`s life ｃyｃle，ＤPLCﻫ名义应力、公称应力nominaｌstressﻫ模块化设计modｕlａｒdeｓign, MDﻫ模块式传动系统moduｌar sysｔemﻫ模幅箱morｐhology ｂｏxﻫ模糊集ｆｕzｚy setﻫ模糊评价ｆｕzｚｙevａlｕatiｏnﻫ模数ｍoduｌｅ摩擦fｒiｃtiｏnﻫ摩擦角frictｉｏn angle摩擦力ｆｒiｃtion foｒｃe摩擦学设计tribｏlogy desigｎ, ＴDﻫ摩擦阻力fｒictional ｒesistaｎｃe摩擦力矩frｉｃtioｎmoｍent摩擦系数coeｆｆiciｅｎt of frｉctｉｏn摩擦圆friｃtion circle磨损ａbrasion wｅar；sｃrａtchinｇ末端执行器end－effectoｒ目标函数objective funｃtiｏn耐腐蚀性corroｓion rｅsistaｎce ﻫ耐磨性wear resiｓｔaｎce挠性机构mｅｃhaｎism with flexiｂle eleｍｅｎtsﻫ挠性转子flexｉｂlｅrotoｒ内齿轮intｅrnal gearﻫ内齿圈ｒinｇgearﻫ内力inｔｅrnal forceﻫ内圈iｎner ring能量eｎergyﻫ能量指示图ｖiｓcｏｓｉtyﻫ逆时针counterclockwｉsｅ（or anticlockｗisｅ）ﻫ啮出eｎgagiｎg－out啮合engageｍｅｎt，ｍesｈ，ｇｅarｉng啮合点contacｔpｏinｔsﻫ啮合角ｗｏrkiｎg prｅsｓuｒe anglｅﻫ啮合线linｅof aｃtiｏｎﻫ啮合线长度lenｇtｈof ｌinｅof ａctiｏｎ啮入ｅｎgagｉnｇ—iｎﻫ牛头刨床shapｅr凝固点frｅeｚing poｉnt；sｏlidifyｉnｇpｏintﻫ扭转应力torｓion strｅss扭矩mｏmeｎｔｏf ｔorqueﻫ扭簧ｈeｌical ｔorｓｉon spring诺模图NomｏgramＯ形密封圈密封O rｉｎg seal盘形凸轮disｋcamﻫ盘形转子disk—likｅrotoｒ抛物线运动ｐaraboｌic mｏtionﻫ疲劳极限fatｉguｅlimitﻫ疲劳强度fａtigue stｒeｎgｔh偏置式offｓeｔﻫ偏(心）距ｏffset ｄistance偏心率ｅｃceｎtｒiciｔy ｒatioﻫ偏心质量eccentric massﻫ偏距圆oｆfset ciｒcｌeﻫ偏心盘eccentrｉc偏置滚子从动件oｆfsｅｔrolleｒｆｏllｏｗerﻫ偏置尖底从动件ｏffsｅtｋｎifｅ—edｇe fｏlloｗerﻫ偏置曲柄滑块机构ofｆsｅtｓlider—cｒａｎk mechａnｉsm拼接matchinｇ评价与决策evaluation ａｎd decｉsioｎ频率ｆrequencyﻫ平带ｆlat ｂelｔ平带传动flat belt drivingﻫ平底从动件ｆlat-face ｆoｌlowerﻫ平底宽度facｅwiｄtｈﻫ平分线ｂisｅcｔor平均应力ａveraｇe ｓtrｅssﻫ平均中径meａn scrｅw ｄｉａmeterﻫ平均速度averａge velocitｙﻫ平衡baｌanｃeﻫ平衡机balancｉng mａcｈineﻫ平衡品质ｂalancinｇｑuaｌｉtyﻫ平衡平面ｃorrecｔiｎｇplａnｅﻫ平衡质量bａlancinｇmａsｓﻫ平衡重ｃouｎterwｅigｈtﻫ平衡转速bａｌancing ｓpeeｄ平面副ｐlａnａr ｐaｉｒ, flat paiｒﻫ平面机构planar mechaｎｉsmﻫ平面运动副planaｒkｉｎｅmａtｉｃpaｉrﻫ平面连杆机构plaｎar linkａｇeﻫ平面凸轮pｌanaｒcａmﻫ平面凸轮机构planar ｃaｍmechanｉｓm平面轴斜齿轮ｐaraｌｌeｌheliｃal ｇeaｒｓﻫ普通平键paｒalｌel keyﻫ其她常用机构otｈeｒｍｅchanisｍiｎmon use ﻫ起动阶段ｓｔａrｔing period启动力矩sｔａrtｉnｇｔｏrｑue气动机构pｎeｕmaｔiｃmｅｃhaniｓm奇异位置singulａr poｓitioｎ起始啮合点initｉal ｃonｔact，beｇinninｇoｆcontaｃt气体轴承gａs beａrｉng千斤顶jaｃｋﻫ嵌入键sunk key强迫振动foｒced vibrａtｉｏn切齿深度depth ｏf cutﻫ曲柄craｎk曲柄存在条件Grashoｆf`ｓｌａw曲柄导杆机构ｃrank shａper (guiｄe-bａｒ）mechanism曲柄滑块机构sliｄer－crank (ｏｒcｒanｋ-slｉder) mechanismﻫ曲柄摇杆机构cｒaｎk-rocｋer ｍｅｃｈanismﻫ曲齿锥齿轮spirａl beｖel geａr 曲率curvature曲率半径ｒadｉｕs of ｃuｒvatｕreﻫ曲面从动件ｃurvｅd-shoe followeｒ曲线拼接cuｒvｅｍatchingﻫ曲线运动curｖilｉnｅar motionﻫ曲轴craｎk ｓｈaｆtﻫ驱动力drｉviｎg forｃeﻫ驱动力矩drｉviｎg momenｔ(tｏrque）ﻫ全齿高whｏｌe dｅｐｔｈ权重集ｗeighｔｓeｔs球ｂallﻫ球面滚子coｎvｅx rolｌｅrﻫ球轴承ball beａrｉｎgﻫ球面副spｈｅrｉc pair球面渐开线spｈeｒｉcal invoｌutｅﻫ球面运动spherical motioｎ球销副spｈere—pin paｉr球坐标操作器polar coorｄｉnａte mａｎｉｐulａtorﻫ燃点spontaneous ｉgｎitｉｏn热平衡hｅat ｂalａｎｃe；thermal equｉｌiｂrｉum ﻫ人字齿轮hｅrrｉnｇbｏｎe ｇear冗余自由度rｅdundaｎt dｅgｒｅe of freｅｄoｍ柔轮flｅxsplｉneﻫ柔性冲击flexible imｐulｓe; soft shocｋﻫ柔性制造系统fｌeｘiｂle manufactuｒｉng system；FMSﻫ柔性自动化flexible automationﻫ润滑油膜lｕbｒiｃａnt ｆilｍ润滑装置ｌｕｂricａtioｎdeｖicｅﻫ润滑lubricationﻫ润滑剂lubｒiｃaｎtﻫ三角形花键ｓeｒration ｓpline三角形螺纹V ｔｈreaｄsｃreｗ三维凸轮thｒee-diｍｅnｓioｎａl ｃａm三心定理Ｋｅnnedy`s theoremﻫ砂轮越程槽ｇrinｄiｎgｗhｅeｌｇroｏveﻫ砂漏hour-glass少齿差行星传动plaｎｅtaryｄrｉve with smalｌtｅethｄｉffereｎce设计方法学desｉgn mｅｔhoｄology设计变量dｅsigｎｖａｒｉable设计约束ｄｅsign coｎsｔｒaintｓﻫ深沟球轴承dｅep grｏove ball bｅａｒｉngﻫ生产阻力proｄuctivｅreｓiｓtａnｃｅ升程rｉｓe升距lift实际廓线ｃam ｐrｏｆileﻫ十字滑块联轴器double slider couｐlinｇ; Ｏldham‘s couplingﻫ矢量vｅｃｔorﻫ输出功oｕtpｕt woｒｋﻫ输出构件o ｕｔput lｉｎkﻫ输出机构ｏutpuｔmechanism输出力矩outpｕt toｒque输出轴outｐutｓhaft输入构件ｉｎput liｎkﻫ数学模型ｍａthematic ｍｏdelﻫ实际啮合线actｕal line oｆaｃtiｏn双滑块机构ｄoubｌｅ—sliｄer mechａniｓm，ellｉpsogｒａpｈﻫ双曲柄机构douｂle crank ｍecｈanism双曲面齿轮hyperboloｉｄgｅａrﻫ双头螺柱studsﻫ双万向联轴节ｃonstａｎt-ｖelocity （or double) unｉveｒsａl joiｎtﻫ双摇杆机构doubｌe rockerｍechaｎiｓm双转块机构Oｌdｈａm coupｌingﻫ双列轴承ｄouｂlｅrow bearingﻫ双向推力轴承double-dｉrｅｃtion thrusｔbｅarｉｎgﻫ松边slaｃk-sｉdeﻫ顺时针clockwiｓｅﻫ瞬心inｓtantａｎeouｓｃenter死点deａd poinｔﻫ四杆机构four—bａｒlinkagｅﻫ速度ｖeｌoｃiｔyﻫ速度不均匀( 波动）系数coefficｉent of spｅed flucｔｕation速度波动speeｄｆluｃtuａtion速度曲线veｌocity diａgｒaｍ速度瞬心instanｔａｎeｏus cｅnter ｏf veloｃｉty塔轮sｔep pulley踏板ｐedal台钳、虎钳ｖice太阳轮sun gｅaｒ弹性滑动elａｓticity sliｄing motioｎﻫ弹性联轴器elａstｉc coupling fｌｅxibｌe coｕｐliｎg弹性套柱销联轴器rｕbber－ｃusｈioned sleeve beａring coｕpliｎg套筒sleeｖe梯形螺纹acme threａd foｒmﻫ特殊运动链ｓpｅcial kinemaｔic chainﻫ特性chａracｔeristicsﻫ替代机构ｅｑuivａｌent mechaniｓｍ调节ｍodｕlａtｉｏn，regulａtion调心滚子轴承self-aligning roｌleｒbearｉng调心球轴承self—aliｇnｉng ｂaｌl bｅariｎgﻫ调心轴承selｆ-aligning beaｒinｇ调速ｓpｅeｄｇovｅrniｎｇ调速电动机aｄjuｓtaｂle sｐeedｍｏtｏrｓﻫ调速系统speed control systeｍ调压调速variabｌe voｌtａge ｃｏntrol调速器ｒegulator，goｖｅｒｎorﻫ铁磁流体密封ferrofluid sｅａl停车阶段stoppiｎg pｈａse停歇dwelｌ同步带synchrｏnous belt同步带传动syncｈronｏｕs belt ｄriｖｅﻫ凸得,凸面体ｃonvexﻫ凸轮camﻫ凸轮倒置机构inversｅcａｍmeｃｈａnismﻫ凸轮机构cam,caｍｍechanｉｓｍ凸轮廓线cam prｏfile凸轮廓线绘制lａyｏut of cａｍｐrｏfile。

机械类翻译参考词汇表表一3dnow!(3d no waiting)alu(arithmetic logic unit，算术逻辑单元)agu(address generation units，地址产成单元)bga(ball grid array，球状矩阵排列)bht(branch prediction table，分支预测表)bpu(branch processing unit，分支处理单元)brach pediction(分支预测)cmos: complementary metal oxide semiconductor，互补金属氧化物半导体cisc(complex instruction set computing，复杂指令集计算机)clk(clock cycle，时钟周期)cob(cache on board，板上集成缓存)cod(cache on die，芯片内集成缓存)cpga(ceramic pin grid array，陶瓷针型栅格阵列)cpu(center processing unit，中央处理器)data forwarding(数据前送)decode(指令解码)dib(dual independent bus，双独立总线)ec(embedded controller，嵌入式控制器)embedded chips(嵌入式)epic(explicitly parallel instruction code，并行指令代码)fadd(floationg point addition，浮点加)fcpga(flip chip pin grid array，反转芯片针脚栅格阵列)fdiv(floationg point divide，浮点除)femms：fast entry/exit multimedia state，快速进入/退出多媒体状态fft(fast fourier transform，快速热欧姆转换)fid(fid：frequency identify，频率鉴别号码)fifo(first input first output，先入先出队列)flip-chip(芯片反转)flop(floating point operations per second，浮点操作/秒)fmul(floationg point multiplication，浮点乘)fpu(float point unit，浮点运算单元)fsub(floationg point subtraction，浮点减)gvpp(generic visual perception processor，常规视觉处理器)hl-pbga: 表面黏著，高耐热、轻薄型塑胶球状矩阵封装ia(intel architecture，英特尔架构)icu(instruction control unit，指令控制单元)id：identify，鉴别号码idf(intel developer forum，英特尔开发者论坛)ieu(integer execution units，整数执行单元)imm: intel mobile module，英特尔移动模块instructions cache，指令缓存instruction coloring(指令分类)ipc(instructions per clock cycle，指令/时钟周期)isa(instruction set architecture，指令集架构)kni(katmai new instructions，katmai新指令集，即sse)latency(潜伏期)ldt(lightning data transport，闪电数据传输总线)local interconnect(局域互连)mesi(modified，exclusive，shared，invalid：修改、排除、共享、废弃) mmx(multimedia extensions，多媒体扩展指令集)mmu(multimedia unit，多媒体单元)mflops(million floationg point/second，每秒百万个浮点操作)mhz(million hertz，兆赫兹)mp(multi-processing，多重处理器架构)mps(multiprocessor specification，多重处理器规范)msrs(model-specific registers，特别模块寄存器)naoc(no-account overclock，无效超频)ni：non-intel，非英特尔olga(organic land grid array，基板栅格阵列)ooo(out of order，乱序执行)pga: pin-grid array(引脚网格阵列)，耗电大post-riscpr(performance rate，性能比率)psn(processor serial numbers，处理器序列号)pib(processor in a box，盒装处理器)ppga(plastic pin grid array，塑胶针状矩阵封装)pqfp(plastic quad flat package，塑料方块平面封装)raw(read after write，写后读)register contention(抢占寄存器)register pressure(寄存器不足)register renaming(寄存器重命名)remark(芯片频率重标识)resource contention(资源冲突)retirement(指令引退)risc(reduced instruction set computing，精简指令集计算机)sec: single edge connector，单边连接器shallow-trench isolation(浅槽隔离)simd(single instruction multiple data，单指令多数据流)sio2f(fluorided silicon oxide，二氧氟化硅)smi(system management interrupt，系统管理中断)smm(system management mode，系统管理模式)smp(symmetric multi-processing，对称式多重处理架构)soi: silicon-on-insulator，绝缘体硅片sonc(system on a chip，系统集成芯片)spec(system performance evaluation corporation，系统性能评估测试)sqrt(square root calculations，平方根计算)sse(streaming simd extensions，单一指令多数据流扩展)superscalar(超标量体系结构)tcp: tape carrier package(薄膜封装)，发热小throughput(吞吐量)tlb(translate look side buffers，翻译旁视缓冲器)uswc(uncacheabled speculative write combination，无缓冲随机联合写操作)valu(vector arithmetic logic unit，向量算术逻辑单元)vliw(very long instruction word，超长指令字)vpu(vector permutate unit，向量排列单元)vpu(vector processing units，向量处理单元，即处理mmx、sse等simd指令的地方)表二Acetyl||乙酰Acid-proof paint||耐酸涂料, 耐酸油漆Acrylic fiber||丙烯酸纤维Acrylic resin||丙烯酸树脂Active filler||活性填料Adapter assembly||接头组件Addition polyimide||加成型聚酰亚胺Addition polymer||加聚物Adjusting valve||调整阀，调节阀Adhersion assembly||粘合装配Adhersion bond||胶结Adjustable-bed press||工作台可调式压力机Adjuster shim||调整垫片Adjusting accuracy||调整精度，调校精度Admissible error||容许误差Admissible load||容许载荷Adsorbed layer||吸附层Advanced composite material||先进复合材料，高级复合材料Advanced development vehicle||试制车，预研样车AE(Automobile Engineering)||汽车工程技术Aeolotropic material||各向异性材料Aerated plastics||泡沫塑料, 多孔塑料Aerodynamic body||流线型车身Aft cross member||底盘/车架后横梁Air bleeder||排气孔Air clamp||气动夹具Air deflector||导流板;导风板，气流偏转板Air intake manifold||进气歧管Air servo||伺服气泵Air-tight joint||气密接头All-plastic molded||全塑模注的All polyster seat||全聚酯座椅Alligatoring||龟裂，涂膜皱皮,表面裂痕Amino resin||氨基树脂Angular test||挠曲试验Anti-chipping primer||抗破裂底漆(底层涂料)Apron||防护挡板Aramid fibre composites||芳胺纤维复合材料Assembly drawing||装配图Assembly jig||装配夹具Assembly part||装配件，组合件Autoclave forming||热压罐成型Autocorrection||自动校正Automatic compensation||自动补偿Automatic feed||自动进料Automobile instrument||汽车仪表板Automotive transmission||汽车传动装置，汽车变速器Auxiliary fasia console||副仪表板Axial strain||轴向应变Axle bushing||轴衬Axle fairing||底盘车桥整流罩A Stage||A 阶段(某些热固性树脂聚合作用的初期阶段)AAC(Auxiliary Air Control)||辅助空气控制ABC(Active Body Control)||主动式车身控制装置Abherent||阻粘剂Ability meter||测力计，性能测试仪ABL (Ablative)||烧蚀剂Ablation||烧蚀Ablative composite material||烧蚀复合材料Ablative insulative material||烧蚀绝热材料Ablative polymer||烧蚀聚合物Ablative prepreg||烧蚀性预浸料Ablative resistance||耐烧蚀性ABR(Acrylate Butadience Rubber)||丙烯酸丁二烯橡胶Abradant material||研磨材料，磨料Abrade||研磨;用喷砂清理Abrasion||磨耗Abrasion coefficient||磨耗系数Abrasion loss||磨耗量，磨损量Abrasion performance||磨耗性Abrasion-proof material||耐磨材料Abrasion resistant paint||耐磨涂料Abrasion test||磨损试验Abrasive blast system||喷砂清理系统Abrasive cloth||砂布</P< p>表三PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号表四A.1. abrasive tooth wear 齿面研磨磨损2. absolute tangential velocity 绝对切向速度3. accelerometer 加速表4. addendum 齿顶高5. addendum angle 齿顶角6. addendum circle 齿顶圆7. addendum surface 上齿面8. adhesive wear 粘着磨损9. adjustability 可调性10. adjustability coefficients 可调系数11. adjusting wedge 圆盘端铣刀的可调型楔块12. allowable stress 允许应力13. alternate blade cutter 双面刀盘14. angular backlash 角侧隙15. angular bevel gears 斜交锥齿轮16. angular displacement 角移位17. angular pitch 齿端距18. angular testing machine 可调角度试验机19. approach action 啮入20. arbor 心轴21. arbor distance 心轴距22. arc of approach 啮入弧23. arc of recess 啮出弧24. attraction 收紧25. average cutter diameter 平均刀尖直径26. axial displacement 轴向位移27. axial factor 轴向系数28. axial locating surface 轴向定位面29. axial pitch 轴向齿距30. axial plane 轴向平面31. axial rakeangle 轴向前角32. axial thrust 轴向推力33. axle testing machine 传动桥试验机B.1. back angle 背锥角2. Back angle distance 背角距(在背锥母线方向)3. Back cone 背锥4. Back cone distance 背锥距5. Back cone element 背锥母线6. Backlash 侧隙7. Backlash tolerance 侧隙公差8. Backlash variation 侧隙变量9. Backlash variation tolerance 侧隙变量公差10. Bandwidth 频带宽11. Base circle 基圆12. Base diameter 基圆直径13. Base pitch 基节14. Base radius 基圆半径15. Base spiral angle 基圆螺旋角16. Basic rack 基本齿条17. Bearing 轴承18. Bearing preload 轴承预负荷19. Bearing spacing/spread 轴承间距20. Bending fatigue 弯曲疲劳21. Bending stress 弯曲应力22. Bevel gears 锥齿轮23. Bias 对角接触24. Bias in 内对角接触25. Bias out 外对角接触26. Blade angle 刀齿齿廓角27. Blade edge radius 刀尖圆角半径28. Blade letter 刀尖凸角代号29. Blade life 刀尖寿命30. Blade point width 刀顶宽31. Blank offset 毛坯偏置距32. Bland position 毛坯位置33. Bottom land 齿槽底面34. Boundary lubrication 界面润滑35. Breakage 破裂36. Bridged contact pattern 桥型接触斑点37. Broach 拉刀38. Burnishing 挤齿C.1. Case crushing 齿面塌陷2. CBN 立方氮化硼3. chamfer 倒角4. chordal addendum 弦齿高5. chordal thickness 弦齿厚6. chuck 卡盘7. circular broach 圆拉刀8. circular face-mill 圆盘端面铣刀9. circular peripheral-mill 圆盘铣刀10. circular pitch 周节11. circular thickness 弧齿厚12. circular thickness factor 弧齿厚系数13. clearance 顶隙14. clearance angle 后角15. coarse pitch 大节距16. coast side 不工作齿侧17. combination 组合18. combined preload 综合预负荷19. complementary crown gears 互补冠状齿轮20. completing cycle 全工序循环21. composite action 双面啮合综合检验误差22. compressive stress 压应力23. concave side 凹面24. concentricity 同心度25. concentricity tester 同心度检查仪26. cone distance 锥距27. cone element 锥面母线28. conformal surfaces 共型表面29. coniskoid 斜锥齿轮30. conjugate gears 共轭齿轮31. conjugate racks 共轭齿条32. contact fatigue 接触疲劳33. contact norma 接触点法线34. contact pattern (tooth contact pattern) 轮齿接触斑点35. contact ratio 重合度36. contact stress 接触应力37. continuous index 连续分度38. control gear 标准齿轮，检验用齿轮39. convex side 凸面40. coolant 冷却液41. corrosive wear 腐蚀性磨损42. corrugated tool 阶梯刨刀43. counter forma surfaces 反法向表面44. cradle 摇台45. cradle test roll 摇台角46. cross 大小端接触47. crossing point 交错点48. crown 齿冠49. crown circle 锥齿轮冠圆50. crowned teeth 鼓形齿51. crown gear 冠轮52. crown to back (轮冠距)轮冠至安装定位面距离53. crown to crossing point 轮冠至相错点距离54. cutter 刀盘55. cutter axial 刀盘的轴向位置56. cutter axial plane 刀盘轴向平面57. cutter axis 刀盘轴线58. cutter diameter 刀盘直径59. cutter edge radius 刀刃圆角半径60. cutter head 刀盘体61. cutter number 刀号62. cutter parallel 刀盘平垫片63. cutter point diameter 刀尖直径64. cutter point radius 刀尖半径65. cutter point width 刀顶距66. cutter spindle 刀盘主轴67. cutter spindle rotation angle 刀盘主轴转角68. cutting distance 切齿安装距69. C.V. testing mashing 常速试验机70. cyclex 格里森粗铣精拉法圆盘端铣刀71. cylindrical gears 圆柱齿轮D.1. Datum tooth 基准齿2. Debur 去毛刺3. Decibel (CB) (噪音)分贝4. Decimal ratio 挂轮比值5. Dedendum 齿根高6. Dendendum angle 齿根角7. Dedendum surface 下齿面8. Deflection 挠曲9. Deflection test 挠曲试验10. Deflection testing machine 挠曲试验机11. Depthwise taper 齿高收缩12. Design data sheet 设计数据表13. Destructive pitting 破坏性点蚀14. Destructive wear 破坏性磨损15. Developed setting 试切调整16. Dial indicator 度盘式指示表17. Diametral pitch 径节18. Diamond 菱形接触19. Dinging ball check 钢球敲击检查20. Disc-mill cuter 盘铣刀21. Dish angle 凹角22. Displacement 位移23. Displacement error 位移误差24. Double index 双分度25. Double roll 双向滚动26. Down roll 向下滚动27. Drive side 工作齿侧28. Duplete 双刃刀29. Duplex 双重双面法30. Duplex helical 双重螺旋法(加工方法之一)31. Duplex spread blade 双重双面刀齿(加工/磨齿方法)32. Duplex taper 双重收缩齿33. Durability factor 耐久系数34. Dynamic factor 动载荷系数E。

英语中机械加工常用术语抛光polishing安装to assemble扳手wrench半机械化semi-mechanization; semi-mechanized半自动滚刀磨床semi-automatic hob grinder半自动化semi-automation; semi-automatic备件spare parts边刨床side planer变速箱transmission gear柄轴arbor部件units; assembly parts插床slotting machine拆卸to disassemble超高速内圆磨床ultra-high-speed internal grinder车床lathe; turning lathe车刀lathe tool车轮车床car wheel lathe车削turning车轴axle衬套bushing 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动899Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具900Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心901Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器902Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手903。

机械工程学专业词汇英语翻译(F)2flowage 蠕变fluctuating liquid drop 振荡液滴fluctuating load 变动载荷fluctuating stress 变应力fluctuation 起伏fluctuation velocity 脉动速度flue gas 烟气fluid 铃fluid clutch 液压离合器fluid dynamics 铃动力学fluid element 铃元fluid filament 细水流量fluid film 铃膜fluid flow 铃怜fluid flow efficiency 怜效率fluid flow physics 铃怜物理fluid friction 铃摩擦fluid friction damping 液体摩擦阻尼fluid kinematics 铃运动学fluid line 铃线fluid lubrication 铃润滑fluid mechanics 铃力学fluid motion 铃运动fluid phase 液相fluid plastic 猎塑料fluid pressure 铃压力fluid surface 伶fluid type instability 铃型不稳定性fluid wave 铃波fluidal 铃的fluidal structure 疗结构fluidic 铃的fluidic element 铃元fluidity 怜性fluidity coefficient 寥fluidization 连化fluidized bed 怜床flume 水沟道flute type deformation 槽型形变flutter 颤振flutter of aerofoil 机翼颤振flux 通量flux density 通量密度flux equilibrium 通量平衡flux of force 力线通量flux peak 通量flying height 飞行高度flying range 航程flying speed 飞行速度flywheel 惯性轮flywheel effect 飞轮效应flywheel fan 飞轮风扇flywheel moment 飞轮力矩foam 泡沫foaming 发泡focal length 焦距focal length ratio 焦距比focal plane 焦面focus of earthquake 震源fokker planck collision term 福克尔普朗克碰撞项fokker planck equation 福克尔普朗克方程folded plate structure 折板结构folded system 折板结构folding 弯曲folding strength 曲折强度folding test 曲折试验follow rest 移动中心架following 追踪following wake 伴流foot 底座force 力force analysis 受力分析force coefficient 力系数force constant 力常数force couple 力偶force density 力密度force dependent on position 与位置依赖的力force dependent on velocity 与速度依赖的力force diagram 力图force distribution 力分布force feed 压力进给force field 力场force free 未受力酌的force function 力函数force in member 构件力force in the bar 杆内酌力force of attraction 引力force of gravity 重力force of inertia 惯性力force of repulsion 斥力force operator 力算符force pipe 压力管force polygon 力多边形force polygon rule 力多边形法force pump 压力泵force sensing of robot 机扑的力感度force sensor 力传感器force system 力系force system of equal effect 等效力系force triangle 力三角形force unbalance 力不平衡force vector 力矢量force voltage analogy 力电压模拟forced circulation 强制循环forced convection 强制对流forced convection air cooler 强制对琳气冷却器forced diffusion 强制扩散forced draught 强制通风forced emission 受迫发射forced oscillations 受迫振荡forced regular precession 强迫规则旋进forced ventilation 强迫通风forced vibration 受迫振荡forced vortex 强制旋涡forced wave 强制波forcing screw 加压螺钉foreshock 前震form drag 形阻力form of bifurcation 分叉形状form of energy 能量形式form of oscillations 振荡形式form of vibrations 振荡形式form resistance 形阻力formation energy 形成能formation enthalpy 形成焓formation entropy 形成熵formation heat 形成热formation of eddy 涡旋形成formation of thermal cracks 热裂形成formation of vortices 涡旋形成formation of waves 波的形成forming 成形forward difference 前向差分forward direction 正向forward movement 前向运动forward scattering 前方散射forward scattering angle 前方散射角forward scattering peak 前方散射峰forward speed 前进速度forward velocity 前进速度forward wave 前向波foucault gyrocompass 傅科陀螺仪foucault pendulum 傅科摆foucault pendulum experiment 傅科摆实验foundation slab 基础底板fountain effect 喷注效应four dimensional force 四维力four dimensional velocity 四维速度four dimensional wave vector 四维波矢量fourier component 傅里叶分量fourier expansion 傅里叶展开fourier integral 傅里叶积分fourier law 傅里叶定律fourier series 傅里叶级数fourier transform 傅里叶变换fourier transformation 傅里叶变换fractional fissure 断裂纹fractural cleavage 破劈理fracture 断裂fracture appearance 断口外观fracture condition 断裂条件fracture criterion 断裂准则fracture dynamics 断裂动力学fracture face 破坏面fracture load 断裂载荷fracture mechanics 断裂力学fracture strain 断裂应变fracture surface 破坏面fracture test 断裂试验fracture toughness 断裂韧性fracturing load 断裂载荷fragility 易碎性fragment 碎片fragmentation 破碎frame 框架frame of reference 参考系frame structure 框架结构framework 框架framework method 框架法framing index 照准标志free air effect 自由空气效应free air overpressure 自由大气超压free body 自由体free boundary 自由边界free boundary flow 自由边界流free convection 自由对流free edge 自由边free end 自由端free energy 自由能free energy density 自由能密度free energy function 自由能函数free enthalpy 自由焓free fall 自由下降free fall apparatus 自由降落装置free fall trajectory 自由降落轨道free fall weir 自两溢吝free falling body 自由落体free flight 自由飞行free flow 自由怜free head 自由水头free internal rotation 自由内转动free jet 自由射流free jet wind tunnel 自由喷射风洞free length 自由长度free mass point 自由质点free meander 自由曲流free molecule flow 自由分子流free motion 自由运动free oscillation 自由振荡free outflow 自由瘤free path 自由程free pendulum 自由摆free period 自由周期free plastic flow 自由塑性怜free regular precession 自由规则旋进free rotation 自由旋转free rotor 自由转子free rotor gyroscope 自由转子陀螺仪free running oscillator 自激振荡器free space 自由空间free space propagation 自由空间传播free spinning 旋转free spinning tunnel 旋转竖直风洞free stream 自由怜free stream mach number 自由另赫数free stream velocity 自由怜速度free surface 自由面free surface flow 自由表面怜free surface of water 自由水面free surface vortex 自由面涡free surface wave 自由表面波free time of flight 自由飞行时间free torsion 自由扭转free vector 自由矢量free vibration 自由振荡free volume 自由体积free volume theory 自由体积理论free vortex 自由涡free vortex system 自由涡恋free wave 自由波freedom of motion 运动的自由度freely supported 自由支承的freezing 凝固freezing method 冻结方法freezing point 凝固点freezing temperature 冻结温度freighter 运输机frequency 频率frequency analysis 频率分析frequency analyzer 频率分析器frequency characteristic 频率特性frequency conversion 频率转换frequency distribution 频率分布frequency division 分频frequency domain 频率范围frequency domain method 频域法frequency drift 频率偏移frequency factor 频率因数frequency instability 频率不稳定性frequency jumping 频率跃变frequency meter 频率计frequency method 频率法frequency modulation 频率灯frequency of fadings 衰减频率frequency of ripple 脉动频率frequency parameter 频率参数frequency range 频率范围frequency response 频率响应frequency spectrum 频谱frequency stability 频率稳定度frequency standard 频率标准frequency synthesis 频率合成fresh water 淡水fresh wind 清风friability 易碎性friction 摩擦friction angle 摩擦角friction brake 摩擦闸friction circle 摩擦圆friction coefficient 摩擦系数friction cone 摩擦圆锥friction constant 摩擦常数friction damper 摩擦减震器friction depth 摩擦深度friction drag 摩擦阻力friction drum 摩擦滚筒friction factor 摩擦系数friction gage 摩擦压力计friction head 摩擦水头friction layer 摩擦层friction moment 摩擦力矩friction of motion 运动摩擦friction of rest 静摩擦friction pendulum 摩擦摆friction resistance 摩擦阻力friction roller 摩擦轮friction shock absorber 摩擦式减振器friction spring 摩擦弹簧friction stress 摩擦应力friction surface 摩擦面friction tensor 摩擦应力张量friction term 摩擦项friction velocity 摩擦速度frictional compensation 摩擦补偿frictional error 摩擦误差frictional force 摩擦力frictional heat 摩擦热frictional loss 摩擦损耗frictional oscillation 摩擦振荡frictional ratio 摩擦比frictional resistance 摩擦阻力frictional work 摩擦功frictionless 无摩擦的frictionless instability 非粘性粱稳定性friedrich diagram 弗里德利希示意图fringe density 条纹密度front 锋面front of the detonation wave 爆震波波前front wave 锋面波front wing 前翼frontal drag 迎面阻力frontal edge 前缘frontal resistance 迎面阻力froude pendulum 弗劳德摆frozen equilibrium 冻结平衡frozen flow 冻结怜frozen in degree of freedom 冻结自由度frozen in field lines 冻结力线frozen in magnetic field 冻结磁场frozen soil 冻土fuel 燃料fulcrum 支点fulcrum of suspension 悬挂点full flow 总量full load 全负荷full power 全功率full scale 实际缩尺full sphere 实心球full wave 全波fully developed turbulence 完全发达湍流fully elastic 完全弹性的fully elastic torsion 完全弹性扭转fully ionized plasma 完全电离等离子体fully plastic 完全塑性的fully plastic torsion 完全塑性扭转fume 烟雾function of bounded variation 有界变分函数function of strain 应变函数functional determinant 函数行列式functional equation 函数方程functional model 函数模型functional similarity 函数相似functional simulation 函数模拟fundamental equation 基本方程fundamental frequency 基频fundamental harmonic 基谐波fundamental matrix 基本矩阵fundamental oscillation 基本振动fundamental resonance 基频谐振fundamental tensor 基本张量fundamental vibration 基本振动fundamental wave 基波fundamental wavelength 基波长funicular polygon 肃边形funnel viscometer 漏斗形粘度计fuzzy optimization 模糊优化fuzzy random vibration 模糊随机振动。

机械类英语翻译3D coordinate measurement 三次元量床 boring machine 搪孔机 cncmilling machine CNC铣床 contouring machine 轮廓锯床 copy grinding machine 仿形磨床 copy lathe 仿形车床 copy milling machine 仿形铣床 copy shaping machine 仿形刨床 cylindrical grinding machine 外圆磨床 die spotting machine 合模机 drilling machine ?孔机 engraving machine 雕刻机engraving E.D.M. 雕模放置加工机 form grinding machine 成形磨床 graphite machine 石墨加工机 horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心 internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机 jig grinding machine 冶具磨床 lap machine 研磨机 machine center 加工制造中心 multi model miller 靠磨铣床NC drilling machine NC钻床 NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程式制作系统 planer 龙门刨床 profile grinding machine 投影磨床 projection grinder 投影磨床 radial drilling machine 旋臂?床 shaper 牛头刨床 surface grinder 平面磨床 try machine 试模机 turret lathe 转塔车床 universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心 wire E.D.M. 线割放电加工机Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码 barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表 work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门 planning department企划部 QC Section 品管科stamping factory冲压厂 painting factory烤漆厂molding factory成型厂common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手hydraulic machine油压机 lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花 welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理 special assistant manager特助 factory director厂长department director部长 deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长 line supervisor线长assistant manager助理to move, to carry, to handle搬运 be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料 to reverse material 翻料 wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料 scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化 scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良 embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件forklift叉车trailer=long vehicle拖板车下面是赠送的保安部制度范本,不需要的可以编辑删除!!!!谢谢!保安部工作制度一、认真贯彻党的路线、方针政策和国家的法津法觃,按照####年度目标的要求,做好####的安全保卫工作,保护全体人员和公私财物的安全,保持####正常的经营秩序和工作秩序。

机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering人体尺寸 human dimension人体测量学 anthropometry; anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor 正反器；触发器；复振器 flip-flop 正反馈；正回输 positive feedback 正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation 正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.) 光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator 多边形力学；力多边形 polygon of force 字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion 夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.) 系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers 拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment 表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism 扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan。