注塑专业英语手册

钣金 machine cover / upper cover/ side cover 锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门 safety door / fixed door / movable door 锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架 machine base / supporting frame理论注射容积 theoretical shot volume实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比 screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力 plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke 模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力 hydraulic ejection force顶针数 nos. of ejector pin液压系统压力 hydraulic system pressure油泵马达 pump motor电热量 heating capacity温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact forceInjection射出Cooling time 冷却时间Holding time 锁模时间Injection alarm time 射出警报时间Injection start delayFinal cushion minimum valueChange-over to holding by valuePlasticizing end valueHydrarlic change-over pressure holding Screwvalue for change-over to holdingChange-over to holding by enable valueHydraulic pressure in holding 锁模压力Filling stage pressure limitInjection speed 射出速度Injection注射Cooling time冷却时间Holding timeInjection alarm time注射报警时间Injection start delay注射开始延时Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable valueHydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模Mould close force关模压力Mould closing safety time.. 时间Mould closing pressure.. 压力1st closing safety stage pressure合模一段压力1st mould closing speed ...成型速度1st stage mould closing speed1st stage mould closing safety position.....位置High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数Holding time 保压时间Injection start delay 注射延迟Injection注射Cooling time冷却时间Holding time保压时间Injection alarm time注射报警时间Injection start delay注射开始延时(注射延时启动延时)Final cushion minimum value最后段位置（最小余量）Change-over to holding by value切换到锁模（保压由位置切换）Plasticizing end value预塑重终点（熔胶终止）Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换Hydraulic pressure in holding锁模力（保压）Filling 填充Injection alarm time 射胶时间Injection start delay 延迟射胶Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置。

Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料/.Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）.m,k.bn 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井V ent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题塑胶产品的不良缺陷:Molding defects Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆毛边:Stringiness/Fragments水口:Flash 或Burrs/Drainage opening披锋:Delamination/Throws over the front气纹:Silver streaks缩水:Sink marks 或Shrink marks变形:Warping 或Twisting色差:Colour streaks燒焦:Burn marks气孔:V oids水口料degraded material1焦痕（RURNS）：由热引起的材料分解。

Injection Mold Technical Terms（一）模具专业基本用词Professional Terms1．塑料— plastic, resin2．样件— sample3．钢料— steel4．注塑机— injection machine, press5．产品— part, product, moulding6．模具— mold, mould, toolA 简易模（样板模）— prototype moldB 量产用模具— production mold 7．三维造型（数模）—3D model, 3D data8．二维产品图— 2D part drawing9．设计— design10．制造— manufacture, build up, construction, fabrication, make11．检验— check, inspection12．测量— measure, inspection13．修改— change, modify, correction14．工程更改— engineer change15．质量— quality16．数量— quantity17．基准— datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何Geometry1．点— point2．线（边）— line, edge3．面faceA 侧面— sideB 表面— surfaceC 外观面— appearance surface 4．壁厚— wall thickness, stock thickness5．加强筋（骨位）— rib6．孔— hole7．细长的槽— slot8．柱位— boss9．角— cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner 10．斜度— angle, taper11. 凹槽—recess , groove二. 分模信息Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating一．产品标识Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号— cavity number4．材料标记— material symbol5．模具编号— mold number (no.)6．日期印— dating insert, date code7．循环印— cycling code8．公司标志— company logo二. 技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称— program name, project name2）产品名称— part name, product name, part description3）产品编号— part number (P/N)4）客户模号— customer mold no.5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位— molding machine size, injection machine size 13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商— manifold manufacturer, manifold supplier 21）浇口位置— gate location / position22）浇口类型— gate type产品标识— stamp information, part identification特殊要求— special instructions1．产品质量及外观要求Part Quality & Appearance Requirement 1）尺寸及公差Dimension & Tolerance①重要尺寸— critical dimension, important dim., key dim.②理论尺寸— nominal dimension③实际尺寸— actual dimension④公差— tolerance⑤公差带— tolerance range⑥尺寸超差— dimension deviation⑦接受（合格）— accept, OK⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit⑩返工— re-work2）产品缺陷（常见的）Defects (normal)①缩水— sink mark, shrinkage②飞边，毛边— flash, burr③段差— mismatch discrepancy④银丝纹，蛇纹— snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）— short shot⑦熔接线— weld line⑧多胶— unwanted plastic⑨拉伤—damage2．产品外观Part Appearance①产品颜色— part color②产品光泽— gloss③皮纹粒度— grain3．常用词汇、词组及短语Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，添加— add, incorporate4）去除，取消— remove, cancel5）满足…的要求，符合，与…要求一致— according to, conform to, satisfy, meet 6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow1）在…范围之内— within2）不可以，不允许，禁止— free from, prevent, avoid3）…，除非有另指—… unless otherwise specified4）…或少于—…or less5）自动化运作— automatic operation6）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.7）分型线上的飞边（披缝）或段差应小于…Burrs o r discrepancy on the P/L shall be … or less.标题栏Title Block1．产品名称— part name2．图纸编号+ 版本号（索引号）— drawing no. + level (index)3．一般公差— general tolerance（三）如何阅读制模标准？How to read tooling standard?一．模具结构术语Mold Construction TermsA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高— Length X Width X Height②模具高度尺寸（模厚）— stack height of mould③模具重量— total weight of mould, mould thickness2．定模底板— front plate, top clamping plate, clamp plate, clamping plate3．定模板— cavity plate, fixed mould plate, A – plate4．动模板— core plate, moving mould plate, B – plate5．支撑板— support plate, backing plate6．间隔板,方铁— support blocks, rails, risers, spacer block7．顶杆固定板— retaining plate, ejector retaining plate8．顶板— ejector plate，bottom clamping plate9．动模底板— back plate10．导柱— guide pillar, leader pin, guide pin11．导套— guide bush, leader pin bush12．复位杆— return pin, push-back pin13．弹簧— spring14．撑头— support pillar15．顶针板导柱、导套— ejection guide pin / bush16．垃圾钉— stop pin, stop button17．模脚— standing-off pillars18．标牌— plaque scutcheonB．成型零部件moulding components1．型芯— core insert2．型腔— cavity insert3．镶针— core pin4．镶块— sub-insert, split5．滑块— slide, sliding split6．斜顶— lifter, angled-lift split, loose coreA 斜顶头— lifter headB 斜顶杆— lifter rod, lifter shaft 7．成型顶杆— moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道— sprueb．分流道runner①主分流道— main runner ②二级分流道— branch runner 分流道断面形状cross-sectional shape of runner①圆形— full round②半圆形— semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）— edge gate, J – gate②侧浇口— side gate③潜伏式浇口— sub-gate, subsurface gate, submarine gate, cashew gate④潜伏式二次浇口(隧道式浇口) — tunnel gate onto feeder post⑤点浇口— pin gate⑥直接浇口(主流道型浇口) — sprue gate, direct gate⑦护耳式浇口— tab gated．模腔— impressione．冷料井— cold slug wellf．热流道— hot runner2．模具零件mold componentsa．定位圈— locating ring, location ring, register ringb．浇口套— sprue bushc．挡圈— stop ringd．浇口镶块— gate inserte．热流道板— manifoldf．热嘴— hot drop\hot sprue分型面及其锁紧、排气Parting Surface, inter-locking & venting1．分型线— parting line ( P/L )2．镶拼线— bodyline, joint line3．平/ 不平的分型面— flat / non – flat parting surface4．封胶面— shut off surfaces, seal-off surfaces5．擦穿位— shut off6．碰穿位— kiss-off7．管位— parting line lock8．分型面的释放(避空) — relief of parting surface9．分型面的平衡— balancing of parting surface10．锁紧角度— locking angle11．锁紧力— clamping force12．锁模块— safety strap13．精定位— Interlock, die lock14．困气— air trap15．排气槽— vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱— angle pin, horn pin, cam pin②弹簧— spring③油缸— hydraulic cylinder2．制动Detention①滑块固定器— slide retainer②弹簧制动器— spring-loaded detention (plunger)③挡钉、挡板— stop pin, stop plate, slide stop3．导轨— gib, guide strip4．锁紧块（楔紧块）— heel block, locking heel, wedge block, chase block 5．耐磨片— wear plate, wear strip6．压板— retainer, gib7．螺钉— screw8．定位销— dowel pinF．斜顶机构Lifter1．斜顶头— lifter head2．斜顶杆— lifter rod, lifter shaft3．开口销— split pin4．固定板（压板）— retainer plate5．耐磨片— wear plate1．铜导套— bronze bushing2．衬套— spacer3．导轨— L – gib4．滑动块— slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程— ejection stroke②模具开档— daylight③粘模— stick④产品脱模— part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板— ejector plate②顶板固定板— retaining plate③推板— stripper plate④推板导柱— ejector guide pin⑤推板导套— ejector guide bush⑥撑头— support pillar3．复位机构Return System①复位杆（回程杆）— return pin, push – back pin②垃圾钉— stop pin, stop button③压簧— compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构— early return system⑥强制复位机构— positive return system4．顶出方法Ejection Techniques1）顶杆顶出— pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出— valve ejection5．顶出元件Ejection Elements1）拉料杆— sprue puller, sucker pin2）顶杆— ejector pin3）阶梯式顶杆— stepped ejector pin1）顶管— ejection sleeve, sleeve2）扁顶— ejector blade, slabbed off ejector pin3）顶块— stripper bar4）顶环— stripper ring5）推板— stripper plate6）加速顶— accelerated ejection1．顶出辅助机构Supplementary operating system1）弹簧柱塞器— spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device2．电器元件Electric Components1）压力传感器— pressure transducer2）限位开关— limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差— temperature variation2）水孔（水道）— waterlines, water-ways, flow-way, channel3）水路— cooling circuit4）水路示意图— water schematic, schematic circuit5）冷却液— coolant, coolant fluid6）内连接— interconnect7）外连接— external connection8）出口、入口— outlet、inlet9）漏水— water leakage2．水路分布Circuits1）阶梯式水路— stepped system2）分隔板水路— baffled hole system3）斜孔式水路— angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片— baffle3）密封圈— O – ring4）快插水路接头— quick disconnect fitting, quick connection adaptor5）弯头— elbow6）偶合器（连接器、接头）— adaptor (including a plug & a socket)7）橡皮管— rubber hose1）分水板,集水块— water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹— thread2．管螺纹— pipe thread3．螺纹孔— screw hole, tapped hole4．起吊孔— handling hole, jack screw hole, eye bolt hole5．螺钉— screw6．内六角螺钉— socket headed cap screw （s.h.c.s.）7．沉头螺钉— flat headed cap screw （f.h.c.s）8．螺栓— bolt9．螺母— nut10．锁紧螺母— locknut11．螺纹标准Thread Standard①公制标准— Metric②英制标准— Imperial③英制管螺纹标准— British Standard Pipe thread （BSP）④美制管螺纹标准— NPT⑤美制粗螺纹标准— United Coarse thread （UNC）⑥美制细螺纹标准— United Fine thread （UNF）H．润滑Lubrication1．润滑槽— grease groove2．加油管— grease line3．油杯— lubrication fittingI. 测量仪器Measuring Instruments1．游标卡尺— vernier caliper2．千分尺— micrometer3．高度规— height gauge4．刻度规— dial gauge5．三坐标测量仪（三次元）— Coordinate Measure Machine（CMM）6．塞规— pin gauge7．圆角量规— radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③水平注塑机导柱间距— tie bar horizontal clearance④台板尺寸— platen dim.⑤最小/ 最大模厚— mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档— open daylight Min. / Max.⑦锁紧行程— clamp stroke⑧锁紧力— clamping force⑨顶出行程— ejector stroke⑩顶出力— ejector force。

注塑英语大全成型工艺流程及条件介绍Mｏｌdiｎg technｉｑue pｒoceｄｕｒe aｎｄparaｍeter ｉntroｄuctioｎ第一节成型工艺Sｅctiｏｎ 1 molｄｉng tecｈniqｕｅ、ﻫ1。

成型工艺参数类型Soｒts ｏf molding parameter.ﻫ (1).注塑参数ｃtion parａｍｅter、ａ、注射量ctｉon rate.ﻫｂ.计量行程Sｃｒew bacｋpoｓiｔｉｏnc、余料量Cushioｎﻫd.防诞量Suｃking bａck ratee。

螺杆转速Scｒew sｐeedf.塑化量Plａstic0 raｔeﻫg、预塑背压Screw baｃk preｓsｕｒeh。

注射压力与保压压力cｔｉon prｅssｕre ａｎd hｏlｄing pｒessｕrei.注射速度ction spｅedﻫ (2)合模参数Clampｉｎg ｐarameterﻫa。

合模力 Cｌａｍping forceb、合模速度Ｃlａmpｉｎg speedc.合模行程。

Clａmｐinｇstrokeﻫd、开模力Opｅｎｉｎg forceﻫe、开模速度Opeｎing spｅｅdﻫf.开模行程Ｏpen ｉng poｓitｉｏｎg、顶出压力Ejeｃtoｒadvaｎce pｒessureﻫh。

顶出速度Eｊｅctｏr advanceｓpeｅｄｉ。

顶出行程Eｊectoｒaｄvance positionﻫﻫ２.温控参数Ｔemperatuｒe parameteｒﻫa、烘料温度Ｄry resiｎmaterial temperatｕreｂ。

料向与喷嘴温度Cｙliｎder teｍpｅrａture ａｎd nｏzzle tｅmperatureﻫc、模具温度Mold temperat ｕreﻫd.油温Oil temperaｔure3、成型周期Molding cyclｅﻫa、循环周期Ｃycle ｔimeb.冷却时间Cooｌｔimｅｃ.注射时间cｔiｏｎtｉmed.保压时间Hoｌdiｎg preｓｓｕre timee。

注塑、模具专业英语Surface Appearance 外观Glossiness/gloss finish 光洁度、粗糙度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露、浮纤Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹、料花Flow mark 流纹Brittle/brittleness 脆、脆性Bubbles/trapped gas 气泡/困气Void 孔、气泡Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃等级V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 颗粒料孔隙、Low impact/tensile strength etc 低冲击强度/拉伸强度等High flow/filler content etc 高流动性/过度填充Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 纤维结团Product was rejected due to 产品不能接受因为…High moisture level 高水分、高湿度Warpage/warped 翘曲/变形Shrinkage/shrink 收缩/收缩率Sink marks 凹陷、缩水Short shot/short molding 打不满、欠注Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边、披锋、溢边Discoloration 变色Off color 颜色差异Flow rate 流动速率Viscous/viscosity 粘性的、粘的/黏度High flow 高流动Low flow 低流动Sticky 粘的，粘性的Sticking core 粘后模，粘模芯Sticking sprue 粘水口Sticking cavity 粘前模Mold release（agent） 脱模(剂)Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％ 减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量模具方面：Ejection system 顶出系统、脱模系统pin 顶针、推杆spring 弹簧Gate type 浇口类型sprue 主流道runner 分流道cavity 模腔Sprue gate 直浇口Pin point gate 点浇口Tab gate 护耳浇口Fan gate 扇形浇口Tunnel or submarine gate 潜伏式浇口Jump gate 跳跃式浇口Diaphragm gate 片状浇口Ring gate 环形浇口The cavity of the mould 模腔Heated cylinder 加热料筒Surface finish 表面光洁度Sink mark 缩水Air trap 困气Gas trapped 气体困着，困气void 空隙，孔galling 烧焦Weld line 熔接痕，熔合线Drag mark 划伤、脱模痕Scratch mark 模具刮花Deformed/ warp 变形Ejector not returned 顶针不回位slide 滑块、行位streak 波纹、条纹、色痕delamination 分层Jetting mark 喷射痕Gate mark 浇口痕rib 筋、加强筋、骨位boss 凸台、凸起、凸痕Melt flow length 熔体流线长度Ejector plate 顶针板Stop pin 限位销Push rod 推杆、顶针Push back pin 复位杆Ejector guide pin 顶针导柱Cold-slug-well 冷料井、冷料穴plate 模板Ejected mark 顶痕，顶白nozzle 喷嘴Surface defect 表面缺陷Air vent 排气口Filling uneven 走胶不平衡、进胶不平衡。

完整的注塑专用英语大全-专用技术术语注塑人必备Surface Appearance 外观Glossiness/gloss finish 光洁度、粗糙度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on thesurface 玻纤外露、浮纤Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹、料花Flow mark 流纹，流痕Brittle/brittleness 脆、脆性Bubbles/trapped gas 气泡/困气V oid 孔、气泡Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃等级V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 颗粒料孔隙、Low impact/tensile strength etc 低冲击强度/拉伸强度等High flow/filler content etc 高流动性/过度填充Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 纤维结团Product was rejected due to 产品不能接受因为…High moisture level 高水分、高湿度Warpage/warped 翘曲/变形Shrinkage/shrink 收缩/收缩率Sink marks 凹陷、缩水Short shot/short molding 打不满、欠注、缺料，短射Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边、披锋、溢边Discoloration 变色Off color 颜色差异Flow rate 流动速率Viscous/viscosity 粘性的、粘的/黏度High flow 高流动Low flow 低流动Sticky 粘的，粘性的Sticking core 粘后模，粘模芯Sticking sprue 粘水口Sticking cavity 粘前模。

abrasive grinding 强力磨削abrasive 磨料的,研磨的absence 不在，缺席accesssory 附件accommodate 适应accordingly 因此,从而,相应地accuracy 精度,准确性actuate 开动(机器),驱动adequate 足够的adhesive 粘合剂adjacent 邻近的adopt 采用advance 进步advisable 可取的agitate 摇动a large extent 很大程度algorithm 算法align 定位，调准alignment 校直all-too-frequent 频繁allowance 容差,余量alternate 交替,轮流alternatively 做为选择,也许aluminiun 铝ample 充足的analysis 分析ancillary 补助的,副的angular 有角的annealing 退火aperture 孔applied loads 作用力appropriate 适当的arc 弧,弓形arise 出现,发生arrange 安排article 制品,产品ascertain 确定,查明assemble 组装attitude 态度auxiliary 辅助的avoid 避免axis 轴axle 轮轴,车轴alternative 替换物backup 备份batch 一批bearing 轴承,支座bed 床身behavior 性能bench-work 钳工工作bend 弯曲beneath 在•••下bin 仓，料架blank 坯料blank 冲裁,落料blanking 落料模blast 一阵（风）blemish 缺点,污点bolster 模座,垫板boring 镗削,镗孔bracket 支架brass 黄铜break down 破坏breakage 破坏brine 盐水brittle 易碎的buffer 缓冲器built-in 内装的bulging 凸肚burr 毛刺bush 衬套by far •••得多,最by means of 借助于boost 推进cabinet 橱柜call upon 要求carbide 碳化物carburzing 渗碳carriage 拖板,大拖板carry along 一起带走carry down over 从•••上取下carry out 完成case hardening 表面硬化case 壳,套cast steel 铸钢casting 铸造,铸件category 种类caution 警告，警示cavity and core plates 凹模和凸模板cavity 型腔,腔,洞centre-drilling 中心孔ceramic 陶瓷制品chain doted line 点划线channel 通道,信道characteristic 特性check 核算chip 切屑,铁屑chuck 卡盘chute 斜道circa 大约circlip (开口)簧环circuit 回路,环路circulate (使)循环clamp 夹紧clamp 压板clay 泥土clearance 间隙clip 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse 崩塌,瓦解collapsible 可分解的combination 组合commence 开始,着手commence 开始commercial 商业的competitive 竞争的complementary 互补的complexity 复杂性complication 复杂化compression 压缩comprise 包含compromise 妥协,折衷concern with 关于concise 简明的,简练的confront 使面临connector 连接口,接头consequent 随之发生的,必然的console 控制台consume 消耗,占用consummate 使完善container 容器contingent 可能发生的CPU (central processing unit) 中央处理器conventional 常规的converge 集中于一点conversant 熟悉的conversion 换算,转换conveyer 运送装置coolant 冷却液coordinate (使)协调copy machine 仿形(加工)机床core 型芯,核心corresponding 相应的counteract 反作用,抵抗couple with 伴随contour 轮廓crack （使）破裂，裂纹critical 临界的cross-hatching 剖面线cross-section drawn 剖面图cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管crush 压碎cryogenic 低温学的crystal 结晶状的cubic 立方的,立方体的cup (使)成杯状,引伸curable 可矫正的curvature 弧线curve 使弯曲cutter bit 刀头,刀片cyanide 氰化物complicated 复杂的dash 破折号daylight 板距decline 下落,下降,减少deform (使)变形demonstrate 证明depict 描述deposite 放置depression 凹穴descend 下降desirable 合适的detail 细节，详情deterioration 退化,恶化determine 决定diagrammmatic 图解的，图表的dictate 支配die 模具,冲模,凹模dielectric 电介质die-set 模架digital 数字式数字dimensional 尺寸的,空间的discharge 放电,卸下,排出discharge 卸下discrete 离散的,分立的dislodge 拉出,取出dissolution 结束distinct 不同的，显著的distort 扭曲distort (使)变形,扭曲distributed system 分布式系统dowel 销子dramaticlly 显著地drastic 激烈的draughting 绘图draughtsman 起草人drawing 制图drill press 钻床drum 鼓轮dual 双的，双重的ductility 延展性dynamic 动力的edge 边缘e.g.(exempli gratia) [拉]例如ejector 排出器ejector plate 顶出板ejector rob 顶杆elasticity 弹性electric dicharge machining 电火花加工electrode 电极electro-deposition 电铸elementary 基本的eliminate 消除,除去elongate (使)伸长,延长emerge 形成,显现emphasise 强调endeavour 尽力engagement 约束,接合enhance 提高,增强ensure 确保，保证erase 抹去,擦掉evaluation 评价,估价eventually 终于evolution 进展excecution 执行,完成execute 执行electrochemical machining 电化学加工exerte 施加experience 经验explosive 爆炸(性)的extend 伸展external 外部的extract 拔出extreme 极端extremely 非常地extremity 极端extrusion 挤压,挤出envisage 设想Fahrenheit 华氏温度fabricate 制作,制造flat-panel technology 平面(显示)技术facility 设备facing 端面车削fall within 属于,适合于fan 风扇far from 毫不,一点不,远非fatigue 疲劳feasible 可行的feature 特色,特征feed 进给feedback 反馈female 阴的,凹形的ferrule 套管file system 文件系统fitter 装配工,钳工fix 使固定,安装fixed half and moving half 定模和动模facilitate 帮助flexibility 适应性,柔性flexible 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing 在前的,前面的foretell 预测,预示,预言forge 锻造forming 成型four screen quadrants 四屏幕象限fracture 破裂free from 免于gap 裂口,间隙gearbox 齿轮箱govern 统治,支配,管理grain 纹理graphic 图解的grasp 抓住grid 格子,网格grind 磨,磨削,研磨grinding 磨光,磨削grinding machine 磨床gripper 抓爪,夹具groove 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套handset 电话听筒hardness 硬度hardware 硬件headstock 床头箱,主轴箱hexagonal 六角形的,六角的hindrance 障碍,障碍物hob 滚刀,冲头hollow-ware 空心件horizontal 水平的hose 软管,水管hyperbolic 双曲线的i.e. (id est) [拉]也就是identical 同样的identify 确定,识别idle 空闲的immediately 正好,恰好impact 冲击impart 给予implement 实现impossibility 不可能impression 型腔in contact with 接触in terms of 依据inasmuch (as) co因为,由于inch-to-metric conversions 英公制转换inclinable 可倾斜的inclusion 内含物inconspicuous 不显眼的incorporate 合并,混合indentation 压痕indenter 压头independently 独自地,独立地inevitably 不可避免地inexpensive 便宜的inherently 固有的injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection 检查,监督installation 安装integration 集成intelligent 智能的intentinonally 加强地，集中地interface 界面internal 内部的interpolation 插值法investment casting 熔模铸造irregular 不规则的，无规律irrespective of 不论,不管irrespective 不顾的,不考虑的issue 发布，发出joint line 结合线kerosene 煤油keyboard 健盘knock 敲，敲打lance 切缝lathe 车床latitude 自由lay out 布置limitation 限度,限制,局限(性) local intelligence 局部智能locate 定位logic 逻辑longitudinal 纵向的longitudinally 纵向的look upon 视作,看待lubrication 润滑machine shop 车间machine table 工作台machining 加工made-to-measure 定做maintenance 维护,维修majority 多数make use of 利用male 阳的,凸形的malfunction 故障mandrel 心轴manifestation 表现,显示massiveness 厚实，大块measure 大小,度量microcomputer 微型计算机microns 微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral 矿物,矿产minimise 把减到最少,最小化minute 微小的mirror image 镜像mirror 镜子moderate 适度的modification 修改,修正modulus 系数mold 模,铸模mold 制模,造型monitor 监控monograph 专著more often than not 常常motivation 动机mould split line 模具分型线moulding 注塑件move away from 抛弃multi-imprssion mould 多型腔模narrow 狭窄的NC (numerical control) 数控nevertheless 然而,不过nonferrous 不含铁的,非铁的normally 通常地novice 新手,初学者nozzle 喷嘴,注口numerical 数字的objectionable 有异议的，讨厌的observe 观察obviously 明显地off-line 脱机的on-line 联机operational 操作的,运作的opportunity 时机,机会opposing 对立的,对面的opposite 反面optimization 最优化orient 确定方向orthodox 正统的，正规的overall 全面的,全部的overbend 过度弯曲overcome 克服,战胜overlaping 重叠overriding 主要的,占优势的opposite 对立的,对面的pack 包装package 包装pallet 货盘panel 面板paraffin 石蜡parallel 平行的penetration 穿透peripheral 外围的periphery 外围permit 许可,允许pessure casting 压力铸造pillar 柱子,导柱pin 销,栓,钉pin-point gate 针点式浇口piston 活塞plan view 主视图plasma 等离子plastic 塑料platen 压板plotter 绘图机plunge 翻孔plunge 投入plunger 柱塞pocket-size 袖珍portray 描绘pot 壶pour 灌,注practicable 行得通的preferable 更好的,更可取的preliminary 初步的，预备的press setter 装模工press 压,压床,冲床,压力机prevent 妨碍primarily 主要地procedure 步骤,方法,程序productivity 生产力profile 轮廓progressively 渐进地project 项目project 凸出projection 突出部分proper 本身的property 特性prototype 原形proximity 接近prudent 谨慎的punch 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase 买，购买push back pin 回程杆pyrometer 高温计quality 质量quandrant 象限quantity 量，数量quench 淬火radial 放射状的ram 撞锤rapid 迅速的rapidly 迅速地raster 光栅raw 未加工的raw material 原材料ream 铰大reaming 扩孔,铰孔recall 记起,想起recede 收回,后退recess 凹槽,凹座,凹进处redundancy 过多re-entrant 凹入的refer 指,涉及,谈及reference 参照,参考refresh display 刷新显示register ring 定位环register 记录,显示,记数regrind 再磨研relative 相当的,比较的relay 继电器release 释放relegate 把降低到reliability 可靠性relief valves 安全阀relief 解除relieve 减轻,解除remainder 剩余物,其余部分removal 取出remove 切除,切削reposition 重新安排represent 代表,象征reputable 有名的,受尊敬的reservoir 容器,储存器resident 驻存的resist 抵抗resistance 阻力,抵抗resolution 分辨率respective 分别的,各自的respond 响应,作出反应responsibility 责任restrain 抑制restrict 限制，限定restriction 限制retain 保持,保留retaining plate 顶出固定板reveal 显示，展现reversal 反向right-angled 成直角的rigidity 钢度rod 杆,棒rotate (使)旋转rough machining 粗加工rough 粗略的routine 程序rubber 橡胶runner and gate systems 流道和浇口系统sand casting 砂型铸造satisfactorily 满意地saw 锯子scale 硬壳score 刻划scrap 废料,边角料,切屑screwcutting 切螺纹seal 密封section cutting plane 剖切面secure 固定secure 紧固,夹紧,固定segment 分割sensitive 敏感的sequence 次序sequential 相继的seriously 严重地servomechanism 伺服机构servomotor 伺服马达setter 安装者set-up 机构sever 切断severity 严重shaded 阴影的shank 柄shear 剪,切shot 注射shrink 收缩side sectional view 侧视图signal 信号similarity 类似simplicity 简单single-point cutting tool 单刃刀具situate 使位于,使处于slide 滑动,滑落slideway 导轨slot 槽slug 嵌条soak 浸,泡,均热software 软件solid 立体,固体solidify (使)凝固solidify (使)固化solution 溶液sophisiticated 尖端的,完善的sound 结实的,坚固的spark erosion 火花蚀刻spindle 主轴spline 花键split 侧向分型,分型spool 线轴springback 反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square 使成方形Servomechanism Laboratoies 伺服机构实验室stage 阶段standardisation 标准化startling 令人吃惊的steadily 稳定地step-by-step 逐步stickiness 粘性stiffness 刚度stock 毛坯,坯料storage tube display 储存管显示storage 储存器straightforward 直接的strain 应变strength 强度stress 压力,应力stress-strain 应力--应变stretch 伸展strike 冲击stringent 严厉的stripper 推板stroke 冲程,行程structrural build-up 结构上形成的sub-base 垫板subject 使受到submerge 淹没subsequent 后来的subsequently 后来,随后substantial 实质的substitute 代替,替换subtract 减,减去suitable 合适的,适当的suitably 合适地sunk 下沉,下陷superior 上好的susceptible 易受影响的sweep away 扫过symmetrical 对称的synchronize 同步,同时发生tactile 触觉的,有触觉的tailstock 尾架tapered 锥形的tapping 攻丝technique 技术tempering 回火tendency 趋向,倾向tensile 拉力的,可拉伸的tension 拉紧,张紧terminal 终端机terminology 术语,用辞theoretically 理论地thereby 因此,从而thermoplastic 热塑性的thermoplastic 热塑性塑料thermoset 热固性thoroughly 十分地,彻底地thread pitch 螺距thread 螺纹thrown up 推上tilt 倾斜,翘起tolerance 公差two-plate mould 双板式注射模tong 火钳tonnage 吨位,总吨数tool point 刀锋tool room 工具车间toolholder 刀夹,工具柄toolmaker 模具制造者toolpost grinder 工具磨床toolpost 刀架torsional 扭转的toughness 韧性trace 追踪transverse 横向的tray 盘，盘子，蝶treatment 处理tremendous 惊人的,巨大的trend 趋势trigger stop 始用挡料销tungsten 钨turning 车削twist 扭曲，扭转tracer-controlled milling machine 仿形铣床ultimately 终于undercut moulding 侧向分型模undercut 侧向分型undercut 底切underfeed 底部进料的undergo 经受underside 下面,下侧undue 不适当的,过度的uniform 统一的,一致的utilize 利用Utopian 乌托邦的,理想化的valve 阀vaporize 汽化vaporize (使)蒸发variation 变化various 不同的,各种的vector feedrate computation 向量进刀速率计算vee 字形velocity 速度versatile 多才多艺的,万用的vertical 垂直的via prep经,通过vicinity 附近viewpoint 观点wander 偏离方向warp 翘曲washer 垫圈wear 磨损well line 结合线whereupon 于是winding 绕,卷with respect to 相对于withstand 经受,经得起work 工件workstage 工序wrinkle 皱纹使皱yield 生产zoom 图象电子放大。

Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra …添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by …预计在…完成Expected order is xMT 预计定单量…吨压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/airbubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluities/superfluous material(alloy) 顶针痕 ejector(pins) mark花纹 flow mark/flow line冷纹 cold mark/cold streak油纹 oil streak走水纹 splash mark银纹 silver streaks霜纹 splay mark夹水纹 silver streaks/flow line/weld line扣模/粘模 spruesticking砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 usingwrong plastic material凸痕 convex mark凹位/凹陷 sink mark/dent mark披锋 flashing批损 pare-mark/cutmark批凹 pare off锉纹 trim-mark/file-mark锉损 excessivetrim mark黑点/黑纹 black spots/black streak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 crakingline碰损 stress mark起皮 chip错位（合模线） part linemisaling ment孔位尺寸改变 dimensionvarious哑色 dull color表面变光滑（喷油面） glossy finishing表面 sruface/outside镶件 insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark偏差 colordeviation色粉 colourment颜色 colour/color零件污糟 dirty mark on part顶白 stressmark/ejector mark屈曲 bent夹模线移位 part line misalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasionmark混色 contamination mark热点不良 poor heat sticking模具方面：定位圈 locating ring唧嘴 spruebush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 top clamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin (导柱)托司 shoulder guide bush(导套)直司 straight guide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripper plate(卸流道板)中边钉 ejector guide pin (顶板导柱)顶针板 ejector retainer plate(顶杆固定板)顶针底板 ejectorplate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin (限位钉)呵 core (后模肉内镶件)后模肉 back mold body(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lockTOP常用塑料原料名称中英文对照表类别俗称中文学名英文学名英文简称主要用途聚苯乙烯类硬胶通用聚苯乙烯 General Purpose Polystyrene PS 灯罩、仪器壳罩、玩具等不脆胶高冲击聚苯乙烯 High Impact Polystyrene HIPS 日用品、电器零件、玩具等改性聚苯乙烯类ABS 料丙烯腈-丁二烯-苯乙烯Acrylonitrile Butadiene Styrene ABS 电器用品外壳,日用品,高级玩具,运动用品AS料(SA料)丙烯腈-苯乙烯Acrylonitrile Styrene AS(SAN) 日用透明器皿,透明家庭电器用品等BS(BDS)K料丁二烯-苯乙烯 Butadiene Styrene BS(BDS) 特种包装,食品容器,笔杆等ASA料丙烯酸-苯乙烯-丙烯睛Acrylonitrile Styrene acrylate copolymer ASA 适于制作一般建筑领域、户外家具、汽车外侧视镜壳体聚丙烯类PP(百折胶) 聚丙烯 Polypropylene PP 包装袋,拉丝,包装物,日用品,玩具等PPC 氯化聚丙烯 Chlorinated Polypropylene PPC 日用品，电器等聚乙烯类LDPE(花料,筒料) 低密度聚乙烯Low Density Polyethylene LDPE包装胶袋,胶花,胶瓶电线,包装物等HDPE(孖力士) 高密度聚乙烯 High Density Polyethylene HDPE 包装,建材,水桶,玩具等改性聚乙烯类EVA(橡皮胶) 乙烯-醋酸乙烯脂 Ethylene-Vinyl Acetate EVA 鞋底,薄膜,板片,通管,日用品等CPE 氯化聚乙烯 Chlorinated Polyethylene CPE 建材,管材,电缆绝缘层,重包装材料聚酰胺类尼龙单6 聚酰胺-6 Polyamide-6 PA-6 轴承,齿轮,油管,容器,日用品尼龙孖6 聚酰胺-66 Polyamide-66 PA-66 机械,汽车,化工,电器装置等尼龙9 聚酰胺-9 Polyamide-9 PA-9 机械零件,泵,电缆护套尼龙1010 聚酰胺-1010 Polyamide-1010 PA-1010 绳缆,管材,齿轮,机械零件丙烯酸脂类亚加力聚甲基丙烯酸甲脂Polymethyl Methacrylate PMMA 透明装饰材料,灯罩,挡风玻璃,仪器表壳丙烯酸脂共聚物改性有机玻璃372# 甲基丙烯酸甲脂-苯乙烯 Polymethyl Methacrylate-Styrene MMS 高抗冲要求的透明制品373# 甲基丙烯酸甲脂-乙二烯 Methyl Methacrylate-Butadiene MMB 机器架壳,框及日用品等聚碳酸脂防弹胶聚碳酸脂 Polycarbonate PC 高抗冲的透明件,作高强度及耐冲击的零部件聚甲醛赛钢聚甲醛 Polyoxymethylene(Polyformaldehyde) POM 耐磨性好,可以作机械的齿轮,轴承等纤维素类赛璐璐硝酸纤维素 Cellulose Nitrate CN 眼镜架,玩具等酸性胶醋酸纤维素 Cellulose Acetate CA 家用器具,工具手柄,容器等乙基纤维素 Ethyl Cellulose EC 工具手柄,体育用品等饱和聚脂涤纶(的确凉) 聚对苯二甲酸乙二醇脂Poly(Ethylene Terephthalare) PET 轴承,链条,齿轮,录音带等聚对苯二甲酸丁二醇脂 Poly(Butylene Terephthalare) PBT聚氯乙烯类PVC 聚氯乙烯 Poly(Vinyl Chloride) PVC 制造棒,管,板材,输油管,电线绝缘层,密封件等氟塑料类PVFF4 氟料聚四氟乙烯 Polytetrafluoroethylene PTFE 高频电子仪器,雷达绝缘部件F46 氟料聚全氟代乙丙烯Perfluorinated Ethylene-Propylene Copolymer FFP 高频电子仪器,雷达绝缘部件F3 氟料聚三氟氯乙烯 Polychlorctrifluoreethylene PCTFE 透明视镜,阀管件等注塑、挤出成型可溶性聚四氟乙烯 Teflon, PFA 化工配件、机械零件注塑、挤出成型四氟乙烯-乙烯共聚 ETFE 化工配件、机械零件聚砜聚砜 polysulfone PSU(PSF) 电器零件,结构件,飞机及汽车零件等聚醚砜 polyethersulfone PES 电器零件,结构件,飞机及汽车零件等氯化聚醚氯化聚醚 Chlorinated Polyethers PENTON(CPT) 代替不锈钢,氯塑料等材料聚苯醚聚苯醚 poly(phenylene oxide) PPO 较高温度下工作的齿轮,轴承,化工设备及零部件聚芳脂聚芳脂PAR 汽车电器,医疗器械聚苯硫醚聚苯硫醚 poly(phenylene sulfone) PPS 耐热性优良,电器零件,汽车零件,化学设备聚醚砜聚醚砜PES 电器开关,插座,齿轮聚甲基戊烯-1聚甲基戊烯-1 TPX 一次性注射器,奶瓶,汽车灯罩酚醛塑料电木粉苯酚-甲醛树脂 Phenol-Formaldehyde PF 无声齿轮,轴承,钢盔,电机,通讯器材配件等氨基塑料电玉尿素脲-甲醛树脂 Urea-Formaldehyde UF 生活用品,电机壳,木材粘接剂等科学瓷美腊密三聚氰氨甲醛树脂 Melamine-Formaldehyde ResinMF 食品,日用品,开关零件等苯氨-甲醛树脂 Aniline-Formaldehyde ResinAF环氧树脂冷凝胶环氧树脂 Epoxide Resin EP 汽车拖拉机零件,船身涂料聚酰亚胺聚酰亚胺 Polyimides PI 太空,电子,飞机零件,汽车零件聚氨脂 PU聚氨脂树脂 Polyurethane ResinPU 鞋底,椅垫床垫,人造皮革,油漆硅树脂 Silicone硅氧烷SI 橡胶制品,脱模剂,乳液弹性体,清漆涂料等不饱和聚脂醇酸树脂 Alkyd ResinAK 涂料,玻璃钢,装饰件,地板,钮扣等烯丙基树脂 Allyl Resin DAP欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。