DIN 53769-2-1986 玻璃纤维增加塑料管道检验.长期静液压试验
- 格式:pdf
- 大小:429.19 KB
- 文档页数:4
“玻璃纤维”(玻璃纤维增强热固树脂)污水管标准规范该标准以固定代号D3262发行,衔接在固定代号后面的数字指出了该标准最初采用的年份,或现今发行版本的修订年份,或者最后修订的年份。
插入符号后面的数字表示了最后审定批准的年份。
上角标(ϵ)指出了自最后修订或重新核定后的版本变化。
1.前言1.1该规范涉及的机器制造玻璃纤维管长度为8英寸(200mm)至144英寸(3700mm),计划施用于排放卫生污水,雨水,以及工业废料的重力流系统。
玻璃纤维增强热固树脂夹砂管和玻璃纤维增强聚合夹砂管均属于玻璃纤维管。
注解 1—依据该规范的要求,聚合物不包括天然聚合物1.2 该规范适用于大部分埋地应用管道,也可适当地为其它安装工程,比如,顶管安装,现有管道隧道衬砌及管道修复等提供参考。
注解 2—ISO标准具有唯一性1.3 该标准中将以英尺-英寸为基本单位,括号中给出的单位值可作为参考。
1.4 下列安全隐患警告只适用于测试方法部分,即该规范第8部分。
本标准帮助使用者建立了安全与健全的操作规范机制,并于使用前确定了该监管机制的适用性。
2.参考文件2.1 美国材料试验协会标准:3C33 混凝土骨料说明D638 塑料拉伸性能测试方法D695 刚性塑料拉伸性能测试方法D790 非增强与增强塑料电气绝缘材料弯曲性能测试方法D883 塑料相关专用术语D1600 塑料相关缩略词专用术语D2412 以平面负载判定塑料管道外部载荷特性的测试方法D2584 固话强化树脂少时量的检测方法D2992 基于“玻璃纤维”(玻璃纤维增强热固树脂)管材和管件的静水压获取方法D3567 测定“玻璃纤维”(玻璃纤维增强热固树脂)管材和管件尺寸的方法D3681 “玻璃纤维”(玻璃纤维增强热固树脂)管材在偏转条件下耐化学性的测定方法D3892 塑料包装实践方法D4161 关于“玻璃纤维”(玻璃纤维增强热固树脂)管道接头使用灵活弹性密封管件的说明F412 塑料管道系统相关专用术语F477 塑料管道弹性密封管件(垫片)说明2.2 美国自来水协会标准:标准C-950,玻璃纤维增强热固树脂管道3.专用术语3.1 定义:3.1.1 规定—除非另有说明,这些定义的内容均与专用术语D883或专用术语F412保持一致,且缩略语严格按照专用术语D1600的要求进行定义。
ICS Q23中华人民共和国国家标准GB/T 21238-2007玻璃纤维增强塑料夹砂管Glass fiber reinforced plastics mortar pipes(ISO 10639:2004(E),Plastics piping systems for pressure and non -pressure water supply---Glass-reinforced thermosetting plastice(GRP) systemts based on unsaturatedpolyester (UP) resin,NEQ)2007-10-21发布 2008-04-01实施中华人民共和国国家质量监督检验检疫总局中国国家标准化管理委员会目次前言 (I)1 范围………………………………………………………………………………………12规范性引用文件 (1)3术语和定义 (1)4分类和标记 (2)5原材料 (3)6要求………………………………………………………………………………………47卫生性能 (10)8试验方法 (10)9检验规则 (12)10标志、包装、运输和贮存……………………………………………………………14附录A(规范性附录)初始环向拉伸强力度样………………………………………15附录B(规范性附录)长期静水压性能试验及确方法……………………………16试验及确定方法……………………………附录C(规范性附录)长期弯曲应弯Sb17附录D(资料性附录)接头技术要求…………………………………………………20附录E(资料性附录)管件技术要求…………………………………………………23前言本标准对应于ISO 10639:2004《压力和非压力给水塑料管系统——玻璃纤维增强热固性塑料(不饱和聚酯树脂)管》(英文版),与ISO 10639的一致性程度为非等效。
本标准自实施之日起,CJ/T3079-1998《玻璃纤维增强塑料夹砂管》,JC/T838-1998《玻璃纤维缠绕增强热固性树脂夹砂压力管》,JC/T695-1998《离心浇铸玻璃纤维增强不饱和聚酯树脂夹砂管废止。
纤维缠绕增强热固性树脂压力管1 主题内容与适用范围本标准规定了玻璃纤维缠绕增强热固性树脂压力管(代号RTRP-FW,下称压力管)的分类、技术要求、试验方法和检验规则等。
本标准适用于以玻璃纤维及其制品为增强材料,热固性树脂为基体,采用缠绕工艺制成的承受内压的压力管。
2 引用标准GB 1446 纤维增强塑料性能试验方法总则GB 2576 纤维增强塑料树脂不可溶分含量试验方法GB 2577 玻璃增强塑料树脂含量试验方法GB 3854 纤维增强塑料巴氏(巴柯尔)硬度试验方法GB 5349 纤维增强热固性塑料管轴向拉伸性能试验方法GB 5351 纤维增强热固性塑料管短时水压失效压力试验方法GB 5352 纤维增强热固性塑料管平行板外载性能试验方法GB/T 13264 不合格品率的小批计数抽样检查程序及抽样表3 分类压力管应按结构层类别,内衬层基体树脂,压力等级和内压失效环向应力进行分类。
3.1 结构层类别3.1.1 结构层增强材料1—无碱玻璃纤维2—中碱玻璃纤维3—其他纤维3.1.2 结构层基体树脂1—间苯型不饮和聚酯树脂2—邻苯型不饮和聚酯树脂3—双酚A型不饮和聚酯树脂4—对苯型不饮和聚酯树脂5—乙烯基酯树脂6—环氧树脂7—酚醛树脂8—其他树脂3.2 内衬层基体树脂1—间苯型不饮和聚酯树酯2—邻苯型不饮和聚酯树脂3—双酚A型不饮和聚酯树脂4—对苯型不饮和聚酯树脂5—乙烯基酯树脂6—环氧树脂7—酚醛树脂8—基他树脂3.3 压力等级1—0.6MPa2—1.0MPa3—1.6MPa4—2.0MPa3.4 内压失效环向应力1—70MPa2—100MPa3—150MPa4—200MPa5—250MPa3 5 标记示例即表示无碱玻璃纤维缠绕增强间苯型不饮和聚酯树脂管,有乙烯基酯树脂内衬,压力等级为1.0MPa,管的短期内压失效环向应力不小于100MPa。
注:上述分类有各种可能的组合,但不意味任何一种组合都对应一种商品管。
I C S83.120Q23中华人民共和国国家标准GB/T21238-2007玻璃纤维增强塑料夹砂管Glassfiber reinforce dplasticsmortarpipes(ISO10639:2004(E),Plasticspipingsystemsforpressureandnon-pressurewatersupply---Glass-reinforcedthermosetting plastice(GRP)systemtsbasedon unsaturatedpolyester(UP)resin,NEQ)2007-10-21发布2008-04-01实施中华人民共和国国家质量监督检验检疫总局中国国家标准化管理委员会目次前言 (I)1范围 (1)2规范性引用文件 (1)3术语和定义 (1)4分类和标记 (2)5原材料 (3)6要求 (4)7卫生性能 (10)8试验方法 (10)9检验规则 (12)10标志、包装、运输和贮存 (14)附录A(规范性附录)初始环向拉伸强力度样 (15)附录B(规范性附录)长期静水压性能试验及确方法 (16)试验及确定方法 (17)附录C(规范性附录)长期弯曲应弯Sb附录D(资料性附录)接头技术要求 (20)附录E(资料性附录)管件技术要求 (23)前言本标准对应于ISO10639:2004《压力和非压力给水塑料管系统——玻璃纤维增强热固性塑料(不饱和聚酯树脂)管》(英文版),与ISO10639的一致性程度为非等效。
本标准自实施之日起,CJ/T3079-1998《玻璃纤维增强塑料夹砂管》,JC/T838-1998《玻璃纤维缠绕增强热固性树脂夹砂压力管》,JC/T695-1998《离心浇铸玻璃纤维增强不饱和聚酯树脂夹砂管废止。
本标准的附录A附录B和附录C为规范性附录,附录D和附录E为资料性附录。
本标准由中国建筑材料工业协会提出。
本标准由全国纤维增强塑料标准化技术委员会口。
纤维缠绕增强塑料贮罐1 主题内容与适用范围本标准规定了玻璃纤维缠绕增强塑料贮罐(以下简称贮罐)的分类、原材料、技术要求、试验方法、检验规则和产品标志、包装、运输和贮存。
本标准适用于缠绕法制造,在常压下贮存液体的地面立式、卧式圆筒形贮罐。
2 引用标准GB 1447 玻璃纤维增强塑料拉伸性能试验方法GB 1449 玻璃纤维增强塑料弯曲性能试验方法GB 1462 纤维增强塑料吸水性试验方法GB 2577 玻璃纤维增强塑料树脂含量试验方法GB 3854 纤维增强塑料巴氏(巴柯尔)硬度试验方法GB 5349 纤维增强热固性塑料管轴向拉伸性能试验方法GB 5351 纤维增强热固性塑料管短时水压失效压力试验方法GB 8237 玻璃纤维增强塑料(玻璃钢)用液体不饱和聚酯树脂JC/T 277 无碱玻璃纤维无捻粗纱JC/T 278 中碱玻璃纤维无捻粗纱JC/T 281 无碱玻璃纤维无捻粗纱布3 分类3.1 按贮罐安装型式分为立式和卧式两种,其公称直径(内径)和公称容积规格系列见表1。
3.2 按贮存的介质类别分为两类,其代号见表2。
3.3 产品命名及其含义见图1。
表1______________________________________________________________________________ 贮罐型式公称直径系列mm 容积系列m3———————————————————————————————————————立式 600、800、1 000、1 200、1 400、1 600、1 800、 1、2、3、4、5、2 000、2 200、2 400、2 600、2 800、3 000、 6、7、8、9、10、12、16、3 200、3 400、3 600、3 800、4 000 20、25、30、40、50、60、70、80、90、100、120、140、160_______________________________________________________________________________续表1 ———————————————————————————————————————贮罐型式公称直径系列mm 容积系列m3———————————————————————————————————————卧式 600、700、800、900、1 000、1 200、 1、2、3、4、1 400、1 600、1 800、2 000、2 200、 5、6、7、8、9、10、12、2 400、2 600、2 800、3 000、3 200、 16、20、25、30、40、50、60、3 400、3 600、3 800、4 000 70、80、90、100、120 ———————————————————————————————————————注:其他规格可按需方要求制造。
公路用玻璃纤维增强塑料管标准下载提示:该文档是本店铺精心编制而成的,希望大家下载后,能够帮助大家解决实际问题。
文档下载后可定制修改,请根据实际需要进行调整和使用,谢谢!本店铺为大家提供各种类型的实用资料,如教育随笔、日记赏析、句子摘抄、古诗大全、经典美文、话题作文、工作总结、词语解析、文案摘录、其他资料等等,想了解不同资料格式和写法,敬请关注!Download tips: This document is carefully compiled by this editor. I hope that after you download it, it can help you solve practical problems. The document can be customized and modified after downloading, please adjust and use it according to actual needs, thank you! In addition, this shop provides you with various types of practical materials, such as educational essays, diary appreciation, sentence excerpts, ancient poems, classic articles, topic composition, work summary, word parsing, copy excerpts, other materials and so on, want to know different data formats and writing methods, please pay attention!公路用玻璃纤维增强塑料管标准解读与应用引言公路建设在现代社会中起着至关重要的作用,而玻璃纤维增强塑料管作为公路建设中的重要材料之一,其质量和标准对公路的建设和运行具有重要影响。
玻璃钢纤维增强塑料夹砂穿套管一.管材形式:玻璃钢纤维增强塑料夹砂管穿套管二.参照规范:GB/T 21238---2007三.检验组批、抽样方法:以相同材料、相同工艺、相同规格的100根FRPM 管为一批(不足100根的也作为一批),随机抽样6根进行外观质量、尺寸、巴氏硬度检验。
四.检测内容4.1 外观质量(归类):FRPM管的内表面应光滑平整,无对使用性能有影响的龟裂、分层、针孔、杂质、贫胶区、气泡和纤维浸润不良等现象;管端面应平齐;边棱应无毛刺;外表面无明显缺陷。
尺寸4.2直径:外径系列应符合表1的规定,内径系列应符合表2的规定4.3 长度:FRPM管的有效长度为3m、4m、5m、6m、9m、10m、12m。
如果需要特殊长度的管,在订货时由供需双方商定。
(看看长度是多少)FRPM管的长度偏差:有效长度的±0.5%。
4.4 管壁厚度:任一截面的管壁平均厚度应不小于规定的设计厚度,其中最小管壁厚度应不小于设计厚度的90%。
(缺少数值)4.5 管壁结构:管壁通常由内衬层、结构层和外表层组成。
内衬层的厚度应不小于1.2mm。
4.6 管端垂直度:管端面垂直度应符合表3的规定。
4.7 巴氏硬度:FRPM管外表面的巴氏硬度应不小于40。
4.8 树脂不可溶成分含量:管壁中树脂的不可溶分量应不小于90%五.初始力学性能测试(按照主控、副控做)5.1 初始环刚度:初始环刚度S0应不小于相应的环刚度等级值SN。
5.2 初始环向拉伸强力Fth:初始环向拉伸强力应根据工程设计来确定,但其最小值根据下式确定:FtL=C1·PN·DN/2当长期静水压设计压力基准实验(HDP)时。
5.3 初始轴向拉伸强力及拉伸断裂应变:a)当管道不承受由管内压直接产生的轴向力或未收到特殊轴向力时,其管壁初始轴向拉伸强力FtL应不小于表6的规定值;管壁轴向拉伸断裂应变应不小于0.25%。
b)当管道承受由管内压产生的轴向力时,其管壁初始轴向拉伸强力FtL应满足式(2)的要求。
玻璃纤维增强塑料外护管技术指标检测方法1 试样检测试样应从室温(23±2)℃下存放16 h后的保温管上切取。
2 表面质量采用外表面无放大目测方法。
外护管颜色应为不饱和聚酯树脂本色或所添加的颜色,检查外护管表面是否有漏胶、纤维外露、气泡、层间脱离、显著性褶皱、色调明显不均等。
3 材料成分应按GB/T 18369、GB/T 18370的规定检测外护管材料中无碱纤维无捻纱、布的主要性能指标,按GB/T 1549的规定检测无碱、中碱玻璃纤维无捻粗纱碱金属氧化物含量,按GB/T 8237的规定检测不饱和聚酯树脂的主要性能指标。
4 密度4.1 密度测试应按GB/T 1463的规定执行。
采用浮力法测定纤维增强塑料外护管材料的密度。
4.2 制取5块试样,质量为1 g~5 g,试样表面应平整光滑。
4.3 采用适当长度的金属丝悬挂试样,金属丝直径小于0.125 mm。
分别称量试样和金属丝的质量,精确到0.1 mg。
将用金属丝悬挂的试样全部浸入量杯内(23±0.5)℃的蒸馏水中,除去试样上的气泡,称量水中的试样质量,精确到0.1 mg。
4.4 根据每次称量的质量数据和蒸馏水密度计算试样材料的密度。
以5块试样密度的算术平均值为测试结果。
4.5 测试仪器:分辨率为0.1 mg的精密天平;精度为±0.5℃的温度计;烧杯或其他容器。
5 拉伸强度5.1 拉伸强度测试应按GB/T 1447的规定执行。
5.2 试样从外护管同一截面上的环向均匀分布位置切取,数量不少于5个,玻璃纤维缠绕的外护管应按纤维方向取样。
试样型式可为哑铃形或长条形,哑铃形试样长度为180 mm、标距为(50±0.5)mm、中间平行段宽度为(10±0.2)mm,长条形试样长度为250 mm、标距为(100±0.5)mm、中间平行段宽度为(25±0.5)mm,试样厚度均为外护管原始厚度。
采用机械加工方法制作。
1 总则1.0.1 为规范石油行业玻璃纤维增强热固性树脂压力管道(简称玻璃钢管道,下同)的施工及验收方法,提高施工技术水平,保证工程质量,制定本规范。
1.0.2 本规范适用于输送介质为液体和气液混合体的埋地和地面敷设及架空安装玻璃钢管道的施工及验收。
1,0.3 玻璃钢管道施工过程中,应遵守国家和地方有关安全、劳动保护、防火、防爆、环境和文物保护等方面的规定。
1.0.4 玻璃钢管道施工及验收除应执行本规范规定外,对已有国家或行业现行标准、规范的管道附属构筑物工程、穿越工程和沟壁支撑工程的施工及验收,以及在特殊地区的施工,尚应执行国家或行业的有关标准和规范的规定。
3 施工的前期准备3.1 技术准备3.1.1 施工单位必须取得设计部门提供的设计文件。
开工前施工:单位应参加设计会审,并自行再次对设计文件进行审查,由设计部门做设计交底,掌握设计要求。
设计文件审查和设计交底应结合现场勘察进行,当发现设计中存在的各类问题时,应及时向设计部门提出变更设计的要求。
3.1.2 施工单位必须编制施工组织设计或施工技术措施,明确施工方案、施工方法,制定技术和质量保证措施或专门的质量计划。
施工组织设计或施工技术措施应报经建设单位审查批准。
3.1.3 按要求准备好现场用质量记录表格。
3.2 现场勘察和放线3.2.1 根据设计图样,施工单位应组织现场勘察,详细了解和掌握管道通过地区的环境条件和土壤条件。
3.2.2 根据施工图样,由施工单位进行测量放线,打管道轴线及两侧定位控制桩,在控制桩上标明桩号、里程和高程。
控制桩应经过复核方可使用,并应及时校核。
3.3 施工用原材料及工具准备3.3.1 施工用管子及管什必须按设计要求订货。
订货合同中应明确规定执行标准、所需产品的规格及类型和数量、树脂类别、管端加工要求、包装要求、供货时间、应提供的产品质量合格证明和验收等内容。
3.3.2 管子及管件等主材和配套材料密封橡胶圈、法兰、阀门等,应于开工前组织拉运至施工现场。
编号中文名称英文名称DIN15551-3-1985 辐射敏感胶卷.硝酸纤维胶卷.术语、特性、用途、贮存Radiation sensitive films; cellulosenitrate film; terminology, properties,utilization, storageDIN 16734-1986 与沥青不相容的人造纤维增强的增塑聚氯乙烯(PVC-P)屋面毡.要求Man-made fibre reinforced plasticizedpolyvinyl chloride (PVC-P) roofingfelt incompatible with bitumen;requirementsDIN 16737-1986 聚氯乙烯(PE-C)制的屋面毡和带编织纤维内衬层的防水薄板材.要求Chlorinated polyethylene (PE-C)roofing felt and waterproofing sheetwith woven fabric inner layer;requirementsDIN 16740-1976 玻璃纤维织物.电气用玻璃纤维织物.交货技术条件Textile glass; textile glass fabrics forelectrical purposes, technical deliveryspecificationsDIN 16741-1976 玻璃纤维织物.电气用带边的玻璃纤维织物带.交货技术条件Textile glass; tapes with edgesconsisting of textile glass fabrics forelectrical purposes, technical deliveryspecificationsDIN 16867-1982 化工管路用玻璃纤维增强式聚酯树脂管道、配件和接头.交货技术条件Glass fibre reinforced polyester resin(UP-GF) pipes, fittings and joints foruse in chemical pipelines; Technicaldelivery conditionsDIN16868-1-1994 玻璃纤维增强式不饱和聚酯树脂(UP-GF)管材.第1部分:缠绕式和填充式.尺寸Glass fibre reinforced unsaturatedpolyester resin (UP-GF) pipes - Part 1:Wound, filled; dimensionsDIN16868-2-1994 玻璃纤维增强式不饱和聚酯树脂(UP-GF)管材.第2部分:缠绕式和填充式.一般质量要求、检验Glass fibre reinforced unsaturatedpolyester resin (UP-GF) pipes - Part 2:Wound, filled; General qualityrequirements, testingDIN16869-1-1995 离心浇注玻璃纤维增强聚脂树脂管(VP-GF).第1部分:尺寸Centrifugally cast filled glass fibrereinforced unsaturated polyester resin(UP-GF) pipes - Part 1: DimensionsDIN16869-2-1995 离心浇注玻璃纤维增强聚脂树脂管(VP-GF).第2部分:一般质量要求、检验Centrifugally cast filled glass fibrereinforced unsaturated polyester resin(UP-GF) pipes - Part 2: Generalquality requirements, testingDIN16870-1-1987 纺织玻璃纤维增强环氧树脂管.尺寸Wound glass fibre reinforced epoxyresin pipes; dimensionsDIN 16871-1982 离心铸塑玻璃纤维增强环氧树脂管.尺寸Centrifugally cast glass fibrereinforced epoxy resin (EP-GF) pipes;DimensionsDIN 16872-1993 热塑性塑料管道用管接头组件.玻璃纤维增强的聚酯树脂(UP-GE)法兰.Pipe joints assemblies for pipelines ofthermoplastics; glass fibre reinforced尺寸polyester resin (UP-GF) flanges;dimensionsDIN 16944-1988 玻璃纤维增强的反应型树脂模塑材料.试验方法Glass fibre reinforced reaction resinmoulding materials; test methodsDIN 16964-1988 绕制玻璃纤维增强聚酯树脂管.一般质量要求和试验Wound glass fibre reinforced polyesterresins (UP-GF) pipes; general qualityrequirements and testingDIN16965-1-1982 绕制玻璃纤维增强聚酯树脂管(UP-GF).A型管.尺寸Wound glass fibre reinforced polyesterresin (UP-GF); pipes, Type A pipes,dimensionsDIN16965-2-1982 绕制玻璃纤维增强聚脂树酯管.B型管.尺寸Wound glass fibre reinforced polyesterresin (UP-GF); pipes, Type B pipes,dimensionsDIN16965-4-1982 纺织玻璃纤维增强聚脂树酯管.管、D管型.尺寸Wound glass fibre reinforced polyesterresin (UP-GF); pipes, Type D pipes,dimensionsDIN16965-5-1982 纺织玻璃纤维增强聚脂树酯管.管、E管型.尺寸Wound glass fibre reinforced polyesterresin (UP-GF); pipes, Type E pipes,dimensionsDIN16966-1-1988 玻璃纤维增强聚酯树脂(UP-GF)异型件和连接件.第1部分:一般质量要求和检验Glass fibre reinforced polyester resin(UP-GF) pipe fittings and jointassemblies; fittings; general qualityrequirements and testingDIN16966-2-1982 玻璃纤维增强式聚酯树脂管道配件和接头.弯管.尺寸Glass fibre reinforced polyester resin(UP-GF) pipe fittings and joints;Elbows, DimensionsDIN16966-4-1982 玻璃纤维增强聚酯树脂管(UP-GF)管件和接头.三通喷管嘴尺寸Glass fibre reinforced polyester resin(UP-GF) pipe fittings an joints; Tees,Nozzles, DimensionsDIN16966-5-1982 玻璃纤维增强聚酯树脂管(UP-GF)管件和接头.缩径管.尺寸Glass fibre reinforced polyester resin(UP-GF) pipe fittings and joints;Reducers, DimensionsDIN16966-6-1982 玻璃纤维增强聚酯树管(UP-GF)管件和接头组件.卡圈、法兰、密封圈、尺寸Glass fibre reinforced polyester resin(UP-GF) pipe fittings and jointassemblies; collars, flanges, joint rings,dimensionsDIN16966-7-1995 玻璃纤维增强聚酯树脂管道连接件及其组件.第7部分:套筒、法兰、法兰连接和对接件.一般质量要求和试验方法Pipe joints and their elements of glassfibre reinforced polyester resins - Part7: Bushings, flanges, flanged and buttjoints; general quality requirementsand test methodsDIN16966-8-1982 玻璃纤维增强聚酯管(UP-GF)管件和接头.层压塑料接头.尺寸Glass fibre reinforced polyester resin(UP-GF) pipe fittings and joints;Laminated joints; DimensionsDIN16967-2-1982 玻璃纤维增强环氧树脂(EP-GF)管件和接头.弯管、三通管、尺寸Glass fibre reinforced epoxy resin(EP-GF) pipe fittings and joints;Elbows, Tees, DimensionsDIN18089-1-1984 防火隔板.防火门填料.矿物纤维板(毡).定义、名称、要求、检验Fire barriers; fillers for fire-doors;mineral fibre boards (felts); definition,designation, requirements, testsDIN 18191-1980 作沥青路衬底的机织玻璃纤维织物Woven glass fabric as inlay bituminoussheetingDIN 18192-1985 作沥青和聚合物沥青薄板镶嵌物的粘合聚酯纤维毡.概念、标志、要求和试验Bonded polyester fleece used as aninlay for bitumen and polymer bitumensheeting; concept, designation,requirements, testingDIN18204-1-2007 用纺织物和塑料薄膜(篷帐布)制造的建筑物和帐篷罩部件.第1部分:涂聚氯乙烯(PVC)的聚酯基底纤维Components for enclosures made oftextile fabrics and plastic films(awnings) for structures and tents -Part 1: PVC coated polyester basefabricDIN18820-1-1991 承载构件用玻璃纤维增强非饱和聚酯树脂和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第1部分:结构、制造和特Laminates of textile glass-reinforcedunsaturated polyester and phenacrylicresins for load-bearing structuralmembers (GF-UP, GF-PHA); structure,manufacture and characteristicsDIN18820-2-1991 承载构件用玻璃纤维增强式非饱和聚酯和苯酚树脂制层压塑料(GF-UP.GF-PHA).第2部分:标准层压塑料的物理参数Laminates of textile glass-reinforcedunsaturared polyester and phenolicresins for load-bearing structuralmembers (GF-UP, GF-PHA); physicalparameters for standard laminatesDIN18820-3-1991 承载构件用玻璃纤维增强非饱和聚酯树脂和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第3部分:承载层压塑料的Laminates of textile glass-reinforcedunsaturated polyester and phenacrylicresins for load-bearing structuralmembers (GF-UP, GF-PHA);protective measures for load-bearinglaminatesDIN18820-4-1991 承载构件用玻璃纤维增强非饱和聚脂树酯和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第4部分:试验和质量控制Laminates of textile glass-reinforcedunsaturated polyester and phenacrylicresins for load-bearing structuralmembers (GF-UP, GF-PHA); tests andquality controlDIN19850-1-1996 污水管道用纤维水泥管和配件件.第1部分:管,支管和弯头尺寸Fibre cement pipes and fittings forsewers - Part 1: Dimensions of pipes,branches and bendsDIN19850-2-1996 纤维水泥污水管和接头.第2部分:接头尺寸Fibre cement pipes and fittings forsewers - Part 2: Dimensions of jointsDIN 2103-1993 办公室机器.油墨带.纺织纤维油墨带Office machines; inked ribbons; wovenfabric ribbonsDIN 28018-2006 玻璃纤维衬钢的压力容器.设备用0.063-10立方米的生产设备用容器Pressure vessels, glass lined steel -Vessels for production plants 0,063m<(hoch)3> up to 10 m<(hoch)3>DIN 28019-2006 玻璃纤维衬钢的压力容器.12.5-125立方米的储存用容器Pressure vessels, glass lined steel -Vessels for storage 12,5 m<(hoch)3>up to 125 m<(hoch)3>DIN28091-2-1995 密封板的交货技术条件.第2部分:纤维基密封材料.要求和试验Technical delivery conditions forgasket sheets - Part 2: Fibre-basedgasket materials (FA); requirementsand testingDIN28136-11-1989 搅拌器.第11部分:玻璃纤维衬里的CE 型公称容量为4000 升更换用刚制搅拌器顶盖喷嘴的位置和尺寸Agitator vessels; position and sizes ofcover nozzles for glass lined steelagitator vessels, type CE, with anominal volume of 4000 litres forreplacement purposesDIN28145-6-1979 玻璃纤维衬里搅拌容器用焊接件.第6部分:支架Parts welded to glass lined agitatorvessels; bracketDIN 29505-1987 航空航天.纤维增强的塑料构件.图纸和零件清单的说明Aerospace; components of fibrereinforced plastics; indications indrawings and parts listsDIN 29965-1992 航空航天.碳纤维.碳纤维素长丝纱.技术规范Aerospace; carbon fibres; carbon fibrefilament yarns; technical specificationDIN 29971-1991 航空航天.不定向碳纤维环氧树脂薄板和预浸渍带.技术规范Aerospace; unidirectional carbonfibre-epoxy sheet and tape prepreg;technical specificationDIN 3068-1972 钢丝绳.6×24标准加7纤维芯的圆形绞股钢丝绳Steel wire ropes; round strand rope 6 ×24 Standard + 7 fibre coresDIN3535-5-1993 煤气供气密封件:煤气管件和煤气设备用橡胶、软木和合成纤维制密封材料.安全性试验要求Sealants for gas supply; sealingmaterials of rubber, cork and syntheticfibres for gas armatures and gasappliances; safety requirements, testsDIN3535-6-1999 供气用密封垫.第6部分:气阀、煤气设备和煤气主管道用基于合成纤维、石墨或聚四氟乙烯的密封垫材料Gaskets for gas supply - Part 6: Gasketmaterials based on synthetic fibres,graphite or polytetrafluoroethylen(PTFE) for gas valves, gas appliancesand gas mainsDIN40604-1-1965 硬化纤维.第1部分:板材、薄板材、条材、带材Vulcanized Fibre; Panels (Sheets),Sheeting, Strips, TapesDIN40604-2-1967硬化纤维.第1部分:管材和棒材Vulcanized fibre; tubes and rodsDIN40763-1-1988 镍镉蓄电池.带纤维结构板的电池.塑料容器电池.标称容量、主要尺寸Nickel-cadmium-batteries; cells withfibre structured plates; cells in plasticcontainers; nominal capacities, maindimensionsDIN40763-2-1990 镍镉蓄电池.带纤维结构板的电池.塑料容器电池.放电电流、最终放电电压、放电时间Nickel-cadmium batteries; cells withfibre structured plates; cells in plasticcontainers; discharge current, finaldischarge voltages, discharge timeDIN4102-17-1990 建筑材料和构件的防火性能.第17部分:矿物纤维绝缘材料熔点的测定.概念、要求和检验Fire behaviour of building materialsand elements; determination of meltingpoint of mineral fibre insulatingmaterials; concepts, requirements andtestingDIN 4195-1976 筛底.丝或化学纤维纺织布.尺寸Screening surfaces; woven filament cloth of silk or man-made fibers, dimensionsDIN 52141-1980 用做屋顶和防水板防护层的玻璃纤维毛状衬料.定义、名称、要求Glass fibre fleece as layer for roof andwater-proof sheeting; definition,designation, requirementsDIN 52142-1978 卷铺屋面料和防水屋面料的载体材料玻璃纤维网.试验程序Glass fibre mat as carrier material forroll roofing and waterproofing; testproceduresDIN 52187-1979 木材的检验.顺纤维方向的极限剪切强度的测定Testing of wood; determination ofultimate shearing stress parallel tograinDIN 52271-1981 矿物纤维绝缘材料的检验.高温性能Testing of mineral fibre insulatingmaterials; Behaviour at elevatedtemperaturesDIN 52274-1986 矿物纤维绝缘材料检验.断裂强度.垂直于绝缘层面的层间抗拉强度测定Testing of mineral fibre insulatingmaterials; determination ofinterlaminar tensile strengthperpendicular to plane of insulatinglayerDIN52275-2-1978 矿物纤维绝缘材料的检验.测定直线尺寸和体密度.管壳Testing of mineral fibrous insulatingmaterials; determination of lineardimensions and bulk density, casingsDIN 52316-1970 玻璃的检验.连续玻璃纤维长丝粗纱的刚性测定Testing of glass; determination ofstiffness of continuous filament glassfibre rovingsDIN 53133-2006 纸板的试验.测定胶粘合波纹纤维板的耐水性Testing of board - Determination ofwater resistance of glue bond ofcorrugated fibreboardDIN 53178-1969 色漆、清漆和类似涂料的检验.喷漆中硝化纤维含量的测定Testing of paints, varnishes and similarproducts; determination of nitrocellulose content of lacquersDIN 53390-1988 玻璃纤维增强塑料的检验.单向玻璃纤维增强层压塑料圆棒的弯曲试验Testing of glass fibre reinforcedplastics; bending test on unidirectionalglass fibre reinforced laminated plastics in the form of round barsDIN 53393-1976 玻璃纤维增强塑料的检验.受化学制品作用的性能Testing of Textile Glass-reinforcedPlastics; Behaviour to the Effect ofChemicalsDIN53766-1-1991 玻璃纤维增强塑料器具和容器的检验.粘合强度的测定Testing of glass fibre reinforcedplastics apparatus and containers;determination of adhesive strengthDIN53769-1-1988 玻璃纤维增强塑料管道检验.第1部分:B型管道配件纵向剪切强度的测定Testing of glass fibre reinforcedplastics pipes; determination of thelongitudinal shear strength of type Bpipe fittingsDIN53769-2-1986 玻璃纤维增加塑料管道检验.长期静液压试验Testing of glass fibre reinforcedplastics pipes; long-term hydrostaticpressure testDIN53769-3-1988 玻璃纤维增强塑料管试验.管子短时间和长时间最大压力试验Testing of glass fibre reinforcedplastics pipes; determination of initialand long-term ring stiffnessDIN53769-6-1989 玻璃纤维增强塑料管道检验.第6部分:受内压脉动作用的管道和配件Testing of glass fibre reinforcedplastics pipes; Testing of pipes andfittings under pulsating internalpressureDIN 53805-1980 纺织品的试验.短纤维长度的测定.术语和一般原则Testing of textiles; determination of thelength of staple fibres; terminologyand general principlesDIN 53806-1970 纺织品的试验.根据精梳纤维长度测量方法测定棉纤维长度Testing of textiles; determination offibre length of cotton according to thecomb staple methodDIN53808-1-2003 纺织品的检验.用单纤维测量法测定纤维长度Testing of textiles - Determination oflength of fibres by measuring ofindividual fibresDIN 53811-1970 纺织品的试验.从显微投影的纵视图中测定纤维的直径Testing of textiles; determination of thediameter of fibres from longitudinalview by microscope projectionDIN 53814-1974 纺织品的检验.纤维和纱段吸湿能力的测定Testing of textiles; determination ofwater retention power of fibres andyarn cuttingsDIN53830-4-1981 纺织品的检验.单根纱线和合股线的线密度的测定.弹性纱线.包括由弹性纤维纺成的包芯纱线.用分段法Testing of textiles; determination oflinear density of single and plied yarns;elasto-yarns including core spun yarnsfrom elastofibres; short length methodDIN53843-2-1988 纺织品的检验.第2部分:纺织纤维的环状拉力试验Testing of textiles; loop tensile test forstaple fibresDIN 纺织品试验.纤维转移倾向的测定.转Testing of textiles - Determination of53865-1998 筒缩绒法fibre migration tendency -Tumble-methodDIN 53941-1983 纺织品的检验.棉纤维马克隆尼值(Micronaire-Wert)的测定Testing of textiles; determination ofmicronaire value of cotton fibresDIN53943-1-1986 纺织品检验.棉纤维的成熟期.第1部分:概念Testing of textiles; cotton fibrematurity; conceptsDIN53943-2-1978 纺织品的检验.第2部分:通过苛性钠溶液的膨胀处理并采用显观法对棉纤维的成熟度的测定Testing of textiles; state of maturity ofcotton fibres, microscopic method,swelling in caustic soda solutionDIN53943-3-1983 纺织品的试验.棉纤维的成熟情况.百分比成熟度的测定.用偏光显微镜的显微镜检验法Testing of textiles; cotton fibrematurity; determination of the percentmaturity; microscopic method using apolarisation microscopeDIN 53944-1993 纺织品的试验.棉纤维计量长度和均匀度的测定Testing of textiles; determination ofgauge length and eveness of cottonDIN 54200-1974 纺织品的检验.用溶解法测定纤维混纺成分的定量测定.原理及应用范围Testing of textiles; quantitativeanalysis of fibre mixtures by means ofsolvent method, basis and field ofapplicationDIN 54201-1975 纺织品的检验.纤维混纺织物的定量分析,一般操作方法Testing of textiles; quantitativeanalysis of fibre mixtures, directionsfor the workDIN 54204-1975 纺织品的检验.羊毛和其它纤维二元混合织物的定量分析.氢氧化钾溶液法Testing of textiles; quantitativeanalysis of binary mixtures, wool withother fibres, potassium hydroxidesolution methodDIN 54205-1975 纺织品试验.二元混合物成份的定量分析.天然或再生纤维素纤维与聚酯纤维.硫酸法Testing of textiles; quantitativeanalysis of binary mixtures, natural orregenerated cellulose fibres withpolyester fibres, sulphuric acid methodDIN 54206-1975 纺织品试验.二元混合物成份的定量分析.蛋白质纤维与其它纤维.次氯酸盐法Testing of textiles; quantitativeanalysis of binary mixtures, proteinfibres with other fibres, hypochloritemethodDIN 54208-2001 纺织品的试验.二元混合物的定量分析.含有其它纤维特别是棉花的再生纤维素纤维.甲酸/氯化锌法Testing of textiles - Quantitativeanalysis of binary mixtures -Regenerated cellulose fibres with otherfibres, especially cotton; Formicacid/zinc chloride methodDIN 54210-1975 纺织品的检验..醋酯纤维素纤维与其它纤维二元混合织物的定量分析.丙酮法Testing of textiles; quantitativeanalysis of binary mixtures, acetatefibres with other fibres, acetonemethodDIN 纺织品的检验.三醋酸短纤维与其它Testing of textiles; quantitative54211-1975 纤维二元混合织物的定量分析.二氯甲烷法analysis of binary mixtures, triacetate fibres with other fibres, dichlormethane (methylene chloride) methodDIN 54212-1975 纺织品的检验.酪蛋白纤维与其它纤维二元混合织物进行定量分析.胰蛋白酶法Testing of textiles; quantitativeanalysis of binary mixtures, caseinfibres with other fibres, trypsin methodDIN 54215-1977 纺织品的检验.聚丙烯纤维与其它纤维二元混合物定量分析.混合二甲苯法Testing of textiles; quantitativeanalysis of binary mixtures,polypropylene fibres with other fibres,xylol methodDIN 54216-1975 纺织品的检验.聚氯乙烯纤维与其它纤维二元混合织物的定量分析.二硫化碳/丙酮法Testing of textiles; quantitativeanalysis of binary mixtures, polyvinylchloride fibres with other fibres,carbon disulphide/acetone methodDIN 54217-1975 纺织品的检验.丙烯酸纤维、改良丙烯酸纤维及某些聚氯乙烯纤维与其它纤维二元混合织物的定量分析.二甲基甲酰Testing of textiles; quantitativeanalysis of binary mixtures, acrylic,modacrylic and certain polyvinylchloride fibres with other fibres,dimethyl formamide methodDIN 54218-1975 纺织品的检验.醋酸纤维与聚氯乙烯纤维二元混合物的定量分析.醋酸法Testing of textiles; quantitativeanalysis of binary mixtures, acetatefibres with polyvinyl chloride fibres,acetic acid methodDIN 54220-1975 纺织品的检验.聚酰胺66纤维或聚酰胺6纤维与其它纤维二元混合织物的定量分析.甲酸法Testing of textiles; quantitativeanalysis of binary mixtures, polyamide6 6 or polyamide 6 fibres with otherfibres, formic acid methodDIN 54221-1975 纺织品的检验.聚酰胺66纤维或聚酰胺6纤维与其它纤维二元混合织物的定量分析.盐酸法Testing of textiles; quantitativeanalysis of binary mixtures, polyamide6 6 or polyamide 6 fibres with otherfibres, hydrochloric acid methodDIN54270-1-1976 纺织品的检验.第1部分:纤维素极限粘度测定原则Testing of textiles; determination of thelimit-viscosity of celluloses, principlesDIN54270-2-1977 纺织品的检验.用氢氧化铜乙二氨溶液法测定纤维素的极限粘度Testing of textiles; determination of thelimit-viscosity of celluloses,Cuen-procedureDIN54270-3-1977 纺织品的检验.第3部分:纤维素极限粘度的测定.EWNN<(指数)mod(NaCl)>程序Testing of textiles; determination of thelimit-viscosity of celluloses,EWNN<(Index)mod(NaCl)>-procedureDIN54270-4-1977 纺织品的检验.用硝酸盐法测定纤维素的极限粘度Testing of textiles; determination of thelimit-viscosity of celluloses, nitrateprocedureDIN 54274-1983 纺织品试验.对聚酰胺纤维中氨端基进行定量测Testing of textiles; quantitativeanalysis of amino end groups inpolyamide fibresDIN 54275-1977 纺织品的检验.用外推法测定纤维材料的pH值Testing of textiles; determination of thepH value of fibre materials, method ofextrapolationDIN 54282-1971 纺织品的检验.醋酸纤维或三醋酸纤维中醋酸含量的测定Testing of textiles; determination ofcontent of acetic acid of acetate ortriacetate fibresDIN 54288-1977 纺织品试验.粘胶纤维中硫的定量测定Testing of textiles; quantitativedetermination of sulfur in viscosefibresDIN 54500-2004 纸的检验.与密度相关的纤维及纸的光散射和吸光系数的测定Testing of paper - Determination of thedensity-related light-scattering andabsorption coefficients of paper andfibre materialsDIN 54813-1994 塑料检验.纺织玻璃纤维增强的聚酯树脂塑料的连接试验.用弯曲剪切试验测定断裂负荷Testing of plastics; testing of joints oftextile glass reinforced polyesterresins; determination of the breakingload by the bending shear testDIN55428-1-1998 包装材料.硬质纤维板.第1部分:要求和试验Packaging materials - Solid fibreboard- Part 1: Requirements, testingDIN55428-2-1998 包装材料.硬质纤维板.第2部分:湿强度.要求和试验Packaging materials - Solid fibreboard- Part 2: Wet strength; requirements,testingDIN55429-2-1987 包装.纸板、硬纤维板或波纹板制箱子.尺寸、极限偏差、尺寸检验Packaging; boxes manufactured fromboard, solid fibre-board or corrugatedboard; dimensions, limit deviations,testing of dimensionsDIN55483-1-1984 包装用橡胶纤维和/或动物纤维.第1部分:要求、检验Rubberized fibre and/or hair forpackaging; requirements, testingDIN55511-1-1984 包装方法.可调整到600mm×400mm、用硬纤维板和波纹板制成的包装箱.带底和折板顶盖的可折叠箱Means of packaging; boxesmanufactured from solid fibre-board orcorrugated board, adjusted to 600 mm400 mm (area module); folding boxeswith bottom and top flapsDIN55511-3-1984 包装方法.可调整到600mm×400mm、用硬纤维板和波纹板制成的包装箱.伸缩式包装箱Means of packaging; boxesmanufactured from solid fibre-board orcorrugated board, adjusted to 600 mm400 mm (area module); telescopeboxesDIN 55952-1981 油漆和清漆的粘合剂.纤维素醚.试验Binders for paints and varnishes;cellulose ethers; testingDIN 油漆和清漆.有机酸纤维素酯.试验Binders for paints and varnishes;55953-1981 cellulose esters of organic acids;testingDIN57441-2-1982 标称电压>1KV系统用有机材料绝缘子试验.带玻璃纤维芯子的户外链式绝缘子的试验(VDE规范)Tests on insulators of organic materialfor systems with nominal voltagesgreater than 1 kV; tests on outdoorcomposite insulators with fibre glasscore [VDE Guide]DIN58140-1-1986纤维光学.术语和符号Fibre optics; terms and symbolsDIN58140-2-1986 纤维光学.纤维光学元件的分类Fibre optics; classification of fibreoptic elementsDIN58141-4-1990 光学纤维元件的检验.光导纤维的直径和厚度的测定Testing of fibre optic elements;determination of diameters andthicknesses of optical fibresDIN58141-5-1993 光纤元件的检验.光导体和图象导体纤维折断率的测定Testing of fibre optic elements;determination of the rate of brokenfibres of light and image conductorsDIN58141-7-1990 光学纤维元件的检验.纤维光缆抗拉载荷的测定Testing of fibre optic elements;determination of tensile load of fibreoptic cablesDIN58141-9-1995 纤维光学元件的检验.第9部分:光学纤维的圆度和同心度偏差的测定Testing of fibre optic elements - Part 9:Determination of deviation of theroundness and the concentricity ofoptical fibresDIN58906-1-2000 止血学.纤维蛋白原浓度测定.第1部分:按测定条款中规定的可凝固的纤维蛋白原的参考测量方法Haemostaseology - Determination offibrinogen concentration - Part 1:Reference measurement procedure forthe determination of clottablefibrinogen as described by ClaussDIN60001-1-2001 纺织纤维.第1部分:天然纤维和字母代码Textile fibres - Part 1: Natural fibresand letter codesDIN60001-2-1990 纺织纤维.第2部分:纤维形状和生产方式Textile fibres; forms of fibres andmanufacturingDIN 60005-2006 纺织吊索.安全.人造纤维一次性单层机织吊索Textile slings - Safety - Disposable flatwoven slings, made of man-madefibresDIN60011-1958亚麻纤维.加工阶段flax fibre; processing phasesDIN 60021-1975 纤维初加工产品和前纺工程产品.术语和定义Products of fibre preparing andpreparatory spinning, terms anddefinitionsDIN 60105-1983 用韧皮纤维纺织法纺制的纱线Yarns produced on bast fibre spinningsystemsDIN 硬纤维纱线Hard fibre yarns60150-1984DIN 60910-1985 纺织纤维和纱线的线性密度.得可萨斯(Tex)体系的换算表Linear densities of textile fibres andyarns; conversion tables for the TexsystemDIN 6141-2000 包装材料.纤维板带盖桶.钢制的底和盖Packaging - Fibreboard drums -Bottom and lid made of steelDIN 61850-1976 纺织玻璃纤维产品和辅助产品.术语和定义Textile glass products and auxiliaryproducts; terms and definitionsDIN61853-1-1987 纺织玻璃纤维.增强塑料用的玻璃纤维毡片.交货技术条件Textile glass; textile glass mats forplastics reinforcement; technicaldelivery conditionsDIN61853-2-1987 纺织玻璃纤维.增强塑料用的玻璃纤维毡片.分类和用途Textile glass; textile glass mats forplastics reinforcement; classificationand applicationDIN61854-1-1987 玻璃纤维织物.塑料增强用的纺织玻璃纤维织物.纺织玻璃长丝织物和纺织粗纱.交货技术条件Textile glass; woven glass fabrics forplastics reinforcement; woven glassfilament fabric and woven roving;technical delivery conditionsDIN61854-2-1987 玻璃纤维织物.塑料增强用的纺织玻璃纤维织物.纺织玻璃长丝织物和纺织粗纱.类型Textile glass; woven glass fabrics forplastics reinforcement; woven glassfilament fabric and woven roving;typesDIN 64165-1977 纺织纤维预梳用的粗梳机.术语、定义和结构原理Carding willow for fibre-preparing;terms and definitions, principles ofconstructionDIN 65060-1991 航空航天.玻璃纤维织物.增强塑料材料用玻璃纤维丝粗纱.技术规范Aerospace; textile glass; textile glassfilament rovings for reinforcement ofplastics; technical specificationDIN 65065-1979 航空航天.纤维增强树脂.技术规范Aerospace; resins for fiber reinforced,technical specificationDIN 65066-1991 航空航天.纺织玻璃纤维.玻璃长丝纱织物.技术规范Aerospace; textile glass; woven glassfilament fabric; technical specificationDIN65067-1-1980 航空航天.具有纤维增强塑料覆盖层(FK)的夹层结构.技术规范Aerospace; sandwich structures withtop layers of fibre reinforced plastics,technical specificationDIN65071-1-1992 航空和航天.纤维增强模塑材料.单向缠绕的纱和粗纱试验板的制备Aerospace; fibre reinforced mouldingmaterials; preparation of test panels ofunidirectional wound yarns androvingsDIN65071-2-1992 航空航天.纤维增强模塑材料.平面增强织物试验板的制备Aerospace; fibre reinforced mouldingmaterials; preparation of test panels ofplain reinforcing fibre productsDIN65071-3-1993 航空和航天.纤维增强模塑材料.蜂窝状预浸渍夹层试验板的制备Aerospace; fibre reinforced mouldingmaterials; preparation ofhoneycomb/prepreg sandwich test panelsDIN 65090-1979 航空航天.用E型玻璃制成的玻璃纤维和预浸玻璃长丝织物(预浸渍体).技术规范条件Aerospace; textile glass,preimpregnated filament glass clothfrom E-glass (Prepreg), technicalspecificationsDIN 65116-1980 航空和航天.硼纤维增强的模塑材料.层压试件的制备Aerospace; boron fibre reinforcedmouldings, preparation of testlaminatesDIN 65117-1980 航空和航天.预浸渍单向硼纤维层(BFK-浸渍体),尺寸、质量Aerospace; preimpregnatedunidirectional boron fibres(BFK-prepreg), dimensions, massesDIN 65142-1989 航空航天.预浸渍的纤维薄板和纤维带(预浸渍的).粘接强度的测定Aerospace; preimpregnated fibre sheetand tape (prepreg); determination ofbond strengthDIN65146-2-1991 航空航天.预浸渍的碳纤维长丝织物和环氧树脂.技术规范Aerospace; preimpregnated wovenfabric of carbon filament yarn andepoxy resin; technical specificationDIN65147-1-1987 航空航天.碳素纤维.碳素纤维长丝织物.尺寸、质量Aerospace; carbon fibres; fabric ofcarbon fibre filament yarn;dimensions, massesDIN65147-2-1987 航空航天.碳纤维.碳纤维长丝织物.技术规范Aerospace; carbon fibres; fabric ofcarbon fibre filament yarn; technicalspecificationDIN 65148-1986 航空航天.纤维增强塑料的试验.用拉伸试验测定中层间的抗剪强度Aerospace; testing of fibre-reinforcedplastics; determination of interlaminarshear strength by tenside testDIN 65184-1993 航空航天.碳纤维.高性能碳纤维素长丝纱.尺寸和质量Aerospace; carbon fibres; highperformance carbon fibre filamentyarns; dimensions, massesDIN 65375-1989 航空航天.纤维增强的塑料.单向层压板的试验.与纤维方向垂直的压力试验Aerospace; fiber reinforced plastics;testing of unidirectional laminates;compression test transverse to fiberdirectionDIN 65378-1989 航空航天.纤维增强的塑料.单向层压板的检验.与纤维方向垂直的拉伸试验Aerospace; fiber reinforced plastics;testing of unidirectional laminates;tensile test transverse to fiber directionDIN 65382-1988 航空航天.塑料用加强纤维.浸渍纱线试样的拉力试验Aerospace; reinforcement fibres forplastics; tensile test of impregnatedyarn test specimensDIN 65383-1997 航空航天.结构用热固环氧树脂纺织玻璃纤维长丝织物预浸渍品.技术规范Aerospace - Thermosetting epoxywoven glass filament fabricpreimpregnated for structuralapplications - Technical specificationDIN 65453-1993 航空航天.碳纤维和双马来酰亚胺树脂或聚酰亚胺树脂制的预浸渍不定向薄板材Aerospace; preimpregnatedunidirectional sheet of carbon fibresand bismaleinimide- or polyimideresin; technical specificationDIN 65466-1996 航空航天.纤维增强塑料.单向层压制品试验.拉伸剪切强度和剪切模数测定Aerospace - Fibre reinforced plastics -Testing of unidirectional laminates;Determination of shear strength andshear modulus in tensionDIN 65469-1992 航空航天.纤维增强的塑料.单层扁平拉伸样件的拉伸试验Aerospace; fibre-reinforced plastics;tensile test of monolayer flat tensionspecimensDIN 65474-1992 航空航天.纤维增强的塑料.温度锋值试验方法Aerospace; fibre reinforced plastics;thermal-spike test methodDIN 65559-1991 航空航天.纤维增强的塑料.多向层压板的试验.缺口孔抗拉强度的测定Aerospace; fibre reinforced plastics;testing of multidirectional laminates;determination of open-hole tensilestrengthDIN 65560-1991 航空航天.纤维增强的塑料.多向层压板的试验.已填充孔抗压强度的测定Aerospace; fibre reinforced plastics;testing of multidirectional laminates;determination of filled-holecompressive strengthDIN 65561-1991 航空航天.纤维增强的塑料.多向层压板的试验.冲击试验负荷后抗压强度的测定Aerospace; fibre reinforced plastics;testing of multidirectional laminates;determination of compressive strengthafter impact testDIN 65562-1991 航空航天.纤维增强的塑料.多向层压板的试验.支承强度的测定Aerospace; fibre reinforced plastics;testing of multidirectional laminates;determination of bearing strengthDIN 65564-1992 航空航天.增强纤维.用HPLC法对碳素长丝纱、织物和短切原丝的浆成份进行定性测定Aerospace; reinforcement fibres;qualitative determination of sizeconstituents of carbon filament yarns,woven fabrics and chopped strands byHPLCDIN 65565-1992 航空航天.增强纤维.用红外分光法对碳素长丝纱、织物和短切原丝的浆类型进行定性试验Aerospace; reinforcement fibres;qualitative testing of size type ofcarbon filament yarns, woven fabricsand chopped strands by infraredspectroscopyDIN 65566-1992 航空航天.增强纤维.碳素长丝纱、织物和短切原丝的浆含量的测定Aerospace; reinforcement fibres;determination of size content of carbonfilament yarns, woven fabrics andchopped strandsDIN 65567-1992 航空航天.增强纤维.芳族聚酰胺长丝纱,织物和短切原丝的整理剂含量的Aerospace; reinforcement fibres;determination of finish content of。
玻璃纤维增强塑料树脂含量试验方法
玻璃纤维增强塑料(GFRP)是一种由玻璃纤维增强树脂制成的复合材料,它具有轻便、高强度、抗腐蚀等优点,被广泛应用于机械制造、建筑工程、汽车制造等领域。
GFRP的性能与其树脂含量密切相关,因此准确测定GFRP的树脂含量是十分必要的。
下面给出10条关于GFRP树脂含量试验的方法:
1. 树脂含量试验原理法:GFRP材料中的玻璃纤维与树脂含量成反比,利用密度差异测定树脂含量。
2. 树脂溶解法:将GFRP样品浸泡在一定温度下的有机溶剂中,树脂溶解后的残留玻璃纤维重量与样品质量比值即为树脂含量。
3. 树脂燃烧分析法:将GFRP样品燃烧后,测定残留物质重量并减去玻璃纤维含量,得到树脂含量。
4. 热分析法:通过热重分析测定GFRP样品的失重率,计算出树脂含量。
5. 红外光谱法:利用红外光谱技术分析GFRP样品树脂中的各类官能团和化学键,从而确定树脂含量。
6. 树脂抽提法:将GFRP样品加入有机溶剂中,使用超声波辅助抽提树脂,并利用色谱等技术分离和检测树脂含量。
7. 树脂吸收法:将GFRP样品浸泡在有机溶剂中,由树脂吸收溶剂,根据不同溶剂的性质适用于不同的树脂。
8. 树脂漂洗法:用一定体积的溶剂沉淀玻璃纤维,用纯溶剂冲洗玻璃纤维,将纯和残余溶剂对比含量计算树脂含量。
9. 泡沫容量法:用GFRP样品中的树脂充满泡沫塞,测量其容量,由泡沫塞的密度与纤维的密度计算树脂含量。
10. 树脂透明法:GFRP样品通过紫外线透射时,将树脂部分筛选出去,计算诱导透明度来确定树脂含量。
以上10种方法均可用于测量 GFRP 树脂含量,具体应根据实验条件和要求选择适合的方法,以保证试验结果的准确性和可靠性。
玻璃纤维增强塑料外护管技术指标检测方法玻璃纤维增强塑料外护管是一种使用含有玻璃纤维增强材料的塑料制成的管道,具有高强度、耐腐蚀、耐高温等特点,在工业领域得到广泛应用。
为了保证玻璃纤维增强塑料外护管的质量和性能,需要对其进行技术指标检测。
本文将介绍玻璃纤维增强塑料外护管的常见技术指标及相应的检测方法。
一、外观质量检测1.观察表面是否平整,是否有裂纹、气泡等缺陷。
检测方法:目测观察。
2.观察管道的颜色是否均匀,有无色差。
检测方法:目测观察。
二、机械性能检测1.拉伸强度测试。
检测方法:使用拉伸试验机,在标准条件下对管道进行拉伸,测量拉伸强度值。
2.弯曲强度测试。
检测方法:使用弯曲试验机,在标准条件下对管道进行弯曲,测量弯曲强度值。
3.冲击强度测试。
检测方法:使用冲击试验机进行冲击试验,测量冲击强度值。
三、尺寸检测1.外径测量。
检测方法:使用外径测量仪对管道的外径进行测量。
2.壁厚测量。
检测方法:使用壁厚测量仪对管道的壁厚进行测量。
四、热稳定性检测1.热变形温度测试。
检测方法:使用热变形温度仪对管道进行热变形温度测试。
2.长期热稳定性测试。
检测方法:将管道置于高温环境中,观察其变形情况和性能变化。
五、耐腐蚀性检测1.浸泡试验。
检测方法:将管道置于不同的腐蚀介质中,观察其耐腐蚀性能。
2.化学性能测试。
检测方法:使用化学性能测试仪器对管道进行化学性能测试。
六、阻燃性检测1.燃烧实验。
检测方法:使用燃烧实验仪对管道进行阻燃性能测试。
七、水质检测1.饮用水接触试验。
检测方法:将管道接触饮用水,检测饮用水中的有害物质含量。
以上是玻璃纤维增强塑料外护管常见的技术指标和相应的检测方法。
通过对这些技术指标的检测,可以有效判断玻璃纤维增强塑料外护管的质量和性能,以确保其在工业领域的应用效果。
玻璃钢管道技术协议买受人:出卖人:2.3 玻璃纤维增强塑料夹砂管(FRPM)技术要求2.3.1 总则本要求包括供水管道工程中FRPM管材的设计、制造、检测以及管材的运输交货和安装技术服务。
2.3.2 原材料2.3.2.1 增强材料采用无碱玻璃纤维及其制品制造FRPM管。
所采用的无碱无捻玻璃纤维纱应符合GB/T18369的规定。
无碱玻璃纤维制品应符合相应的国家标准或行业标准的规定。
2.3.2.2 树脂(1)不饱和聚酯树脂是玻璃钢管的基体材料,除了高强度的力学性能外,还应具有良好的耐水解性能。
本次招标的玻璃钢管采用的不饱和聚酯树脂应具有质量技术监督部门出具的不饱和聚酯树脂性能指标的检测报告,树脂应符合GB/T8237的规定。
(2)内衬层树脂应采用食品级间苯型不饱和聚树脂,其卫生指标必须满足GB13115的规定,投标人需提供相关部门提供的检验报告。
(2)树脂浇铸体的性能应满足GB/T 21238-2007中5.2.4的要求,并提供合格检验报告。
(3)颗粒材料:颗粒材料的最大粒径不得大于2.5mm和五分之一管壁厚度之间的较小值,其中石英砂的SiO2含量应大于95%,含水量应不大于0.2%,碳酸钙的CaCO3含量应大于98%,含水量应不大于0.2%。
2.3.2.3 密封材料密封材料应选用耐酸、耐碱、耐有机溶剂、耐氧化剂的丁基胶圈或优于丁基胶圈的产品,并保证所选材料对供水水质无污染。
2.3.3 技术要求2.3.3.1 使用年限:不小于50年2.3.3.2 外观质量管道内表明应光滑平整,无对使用性能有影响的龟裂、分层、针孔、杂质、贫胶区、气泡和纤维浸润不良等现象;管端面应平齐;边棱应无毛刺;外表面无明显缺陷。
2.3.3.3 尺寸(1)直径管道公称直径采用DN=500mm和DN=600mm。
内直径最大值和最小值应符合GB/T 21238-2007中6.2.1的规定。
(2)长度管道有效长度采用L=12m。
(3)管壁厚度任一截面的壁厚平均厚度应不小于规定的设计厚度,其中最小管壁厚度应不小于设计厚度的90%,内衬层的厚度应不小于1.2mm。