OMRON温度传感器

WiringPrecautions for Safe Use1)The product is designed for indoor use only. Do not use the product outdoors•or in any of the following locations.E Places directly subject to heat radiated from heating equipment.E Places subject to splashing liquid or oil atmosphere.E Places subject to direct sunlight. Places subject to icing and condensation. E Places subject to dust or corrosive gas (in particular, sulfide gas andammonia gas).E Places subject to intense temperature change.E Places subject to vibration and large shocks.2)Use/store within the rated temperature and humidity ranges.Provide forcedcooling if required.3)Install K8AB in a correct direction.4)Be sure to wire properly with correct polarity of terminals.5)Wire the input and output terminals correctly.6)Use this product within the rated load and power supply.7)Be sure that the temperature sensor type and the input type set on K8AB arethe same.8)When extending the lead wires on a thermocouple, be sure to use compensating conductors suitable for the thermocouple type.9)When extending the lead wires on a platinum resistance thermometer, uselead wires with a low resistance (5 ƒ max. per line) and be sure that the resistance is the same for all three lead wires.10)Use the recommended solderless terminals.11)Do not wire the terminals which are not used.12)Make sure that the rated voltage is attained within 1 seconds13)Design system (control panel, etc) considering the 1 second of delay thatK8AB's output to be determined after power ON.14)Make sure that K8AB has 30 minutes or more to warm up after power ON.Turning ON the power before starting monitor to the correct temperature.15)Separate the high-voltage or large-current power lines from other lines, andavoid parallel or common wiring with the power lines when you are wiring to the terminals.16)Allow as much space as possible between K8AB and devices that generatepowerful high frequencies or surge.17)Do not use a microwave receiver near K8AB. Microwave interference mayaffect K8AB.18) A switch or circuit breaker should be provided close to this unit. The switch orcircuit breaker should be within easy reach of the operator, and must be marked as a disconnecting means for this unit.19)Do not use paint thinner or similar chemical to clean with. Use standard gradealcohol.20)Use tools when dismantling parts for disposal.21)Install the K8AB inside a cabinet.22) This is a class A product. In residential area‚ it may cause radio interference,in which case the user may be required to take adequate measures to reduce interference.SpecificationsPower supply voltage Operating frequency Operating valtage rangeOperating frequency rangePower consumption Inrus current Accuracy Relay outputAmbient temperatureAmbient humidity Strage temperature Strage humidity WeightDegree of protection Altitude Installation environmentExternal input Output currentMemory protectionAC100-240V type AC/DC24V type 50-60Hz85 to 110% of the rated voltage 95 to 105% of the rated frequency5VA max.(AC100-240V)4VA max.(AC24V)2W max.(DC24V)15A max.(AC100-240V)10A max.(AC/DC24V)2%FS3A,250VAC/30VDC(resisteve load)1A,250VAC/30VDC(inductive load)Mechanical life 10million times Electorical life 50,000times(N.O) 30,000times(N.C)1c contact -10 to 55•(Avoide freezing or condensation)RH 25 to 85%-25 to 65•RH 25 to 85%Approx.130g IP20Max 2,000mSetup category ‡U ,pollutionDegree 2(as per EN61010-1)Output current:approx.10mAContact input ON :1kƒ max., OFF:100kƒ min.No-contact input ON :residual voltage (NPN) 1.5Vmax.,OFF:leakage current 0.1mA min. EEPROM(non-volatile memory)(endurance:200,000 erase/write cycles)Dimensions (mm)Names of partsSetting rangeSensor input rangeSwitch OperationTime ChartMountingDismountingConnectionsTH11STH12SSolderless terminals Use the small screw driver when you operate the SWs or the Button.OMRON ELECTRONICS LLC.One Commerce Drive Schaumburg, IL 60173-5302 U.S.A Phone 1-847-843-7900 FAX 1-847-843-7787OMRON CANADA INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8, Canada Phone 1-416-286-6465 Fax 1-416-286-6648OMRON EUROPE B.V.Wegalaan 67-69 2132 JD Hoofddorp The Netherlands Phone 31-23-56-81-300 FAX 31-23-56-81-388OMRON ELECTRONICS PTY. LTD. 71 Epping Road, North Ryde, Sydney, N.S.W 2113, Australia Phone 61-2-9878-6377 Fax 61-2-9878-6981OMRON ASIA PACIFIC PTE. LTD.No.438A Alexandra Road #05-05/08(Lobby 2), Alexandra Technopark, Singapore 119967Phone 65-6835-3011 FAX 65-6835-2711OMRON CORPORATIONShiokoji Horikawa, Shimogyo-ku, KYOTO, 600-8530 Japan Phone 81-75-344-7109 FAX 81-75-344-7149Alarm type:Hysteresis 2•(or ßF )Non-failsafe/Failsafe Latch:Holding the relay output until •g latch reset”SV protect mode: In this mode, the changes of SW or R_SWs are • • NOT available. When K8AB comes out from this • •mode, the changes are available.Behavior of LEDs Relay(Failsafe)Relay(Non-failsafe)Alarm, Other errs Source Relay(Latch)Alarm, Other errsSourceSV protect modeSourcePWR_LED Sv protect modeSourceALM_LEDAlarm Source Other errs Lower-limit alarm Upper-limit alarm SV* Other errs:Sensor burnout,Input range over,Setting range over, memory err.* If LATCH_RST or EXTERNAL INPUT has been ON more than 5s, K8AB-TH goes into or comes out from SV protect mode.SWErrors(ALM_LED:flash)Comes out of SV protect mode.A Reset the latch.B Confirm the wiring and parameter settings.C Reset the SOUCE.If K8AB return to normal state, the cause may be the • noise.If not, there is need to replace it.The state of latched output and the state of SV • protect mode are backed up by EEPROM.Trouble shootingFollowing (1)•(3) may occur.(1)Sensor burn out or Senor input range over. (2)Setting range over.(3)Inner error(devices,memories,etc.).O NOF FF O N F OF FF O N F OF F。

The unique dust separating structure, developed by OMRON is a compact and highly efficient FLOW-SENSOR.•A dust-resistant design has been taken into consideration, by the original dust segregation structure, of OMRON.•+/-10% Full-Scale repeatable accuracy achieves consistent air velocity measurement.•Applications include clogged-filter detection and air velocity.Sensor specificationAbsolute maximum ratingOutput characteristicMeasurement condition: Power-supply voltage 3.3VDC, ambient temperature 25°C and dry air.Note:1.Air velocity is the value converted from the mass-flow in OMRON regulation wind tunnel phi48mm.2.The air velocity, set to the Measurement Law, is not shown. Please confirm in a real use environment in use.3.T emperature characteristics:Over ambient temperature range -10 to +60°C: within ±20% F .S. of detected characteristics Of at +25°C.Type D6F-V03A1Flow Range 0 – 3 m/s @ 25°C, 1 atmosphere Case Material Thermoplastic resin GasAirAmbient Temperature -10 to +60°C (with no condensation)Using Humidity Max. 85% RH (with no condensation)Storage Temperature -40 to +80°C (with no condensation)Preservation Humidity Max. 85% RH (with no condensation)Power Supply Voltage 3.15 to 3.45 VDCOutput Signal Analog output 0.5 to 2 VDC (non-linear output)Load resistance min. 10k ΩCurrent Consumption Max. 15mA (No-load, V CC = 3.3 VDC, 25°C)Insulation Resistance20Mohm min. (500VDC, between lead terminal and the case)Dielectric Withstanding Voltage Leakage current is 1mA max. (at 500 VAC, 50/60Hz for one minute).500VAC, 50/60Hz judged at 1mA max. (between the lead terminals and the case)ItemSymbol Rating Unit Power supply voltage V CC 12.0VDC Output voltageV OUT3.0VDCFlow Velocity (m/sec)00.75 1.50 2.25 3.00Output Voltage (VDC)0.50±0.150.70±0.151.11±0.151.58±0.152.00±0.15DimensionsOmron Electronic Components, LLCTerms and Conditions of Sales1.Definitions: The words used herein are defined as follows.(a) Terms:These terms and conditions(b) Seller:Omron Electronic Components LLC and its subsidiaries(c) Buyer:The buyer of Products, including any end user in section III through VI(d) Products:Products and/or services of Seller(e) Including:Including without limitation2.Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's purchase order or other documents which are inconsistent with, or in addition to, these Terms.3.Distributor: Any distributor shall inform its customer of the contents after and includingsection III of these Terms.1.Prices; Payment: All prices stated are current, subject to change without notice by Seller.Buyer agrees to pay the price in effect at time of shipment. Payments for Products received are due net 30 days unless otherwise stated in the invoice. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice.2.Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent toBuyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past due amounts owing to Seller.3.Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximumlegal rate, whichever is less, on any balance not paid within the stated terms.4.Orders: Seller will accept no order less than 200 U.S. dollars net billing.5.Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyershall make remittance to Seller at the then current exchange rate most favorable to Seller; provided that if remittance is not made when due, Buyer will convert the amount to U.S. dollars at the then current exchange rate most favorable to Seller availableduring the period between the due date and the date remittance is actually made.ernmental Approvals: Buyer shall be responsible for all costs involved in obtainingany government approvals regarding the importation or sale of the Products.7.Taxes: All taxes, duties and other governmental charges (other than general real propertyand income taxes), including any interest or penalties thereon, imposed directly orindirectly on Seller or required to be collected directly or indirectly by Seller for themanufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Seller.8.Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,Seller reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Seller may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts.9.Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyerindemnifies Seller fully against all costs or expenses arising in connection therewith. 10.Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting fromcauses beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority.11.Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:(a) All sales and shipments of Products shall be FOB shipping point (unless otherwisestated in writing by Seller), at which point title to and all risk of loss of the Products shall pass from Seller to Buyer, provided that Seller shall retain a security interest in theProducts until the full purchase price is paid by Buyer;(b) Delivery and shipping dates are estimates only; and(c) Seller will package Products as it deems proper for protection against normalhandling and extra charges apply to special conditions.12.Claims: Any claim by Buyer against Seller for shortage or damage to the Productsoccurring before delivery to the carrier must be presented in detail in writing to Seller within 30 days of receipt of shipment.1.Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANYOMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONICCOMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E) SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.Buyer acknowledges that it alone has determined that the Products will meet theirrequirements of the intended use in all cases. Buyer must know and observe allprohibitions of use applicable to the Product/s.e with Attention: The followings are some examples of applications for whichparticular attention must be given. This is not intended to be an exhaustive list of all possible use of any Product, nor to imply that any use listed may be suitable for any Product:(a) Outdoor use, use involving potential chemical contamination or electricalinterference.(b) Use in consumer Products or any use in significant quantities.(c) Energy control systems, combustion systems, railroad systems, aviation systems,medical equipment, amusement machines, vehicles, safety equipment, andinstallations subject to separate industry or government regulations.(d) Systems, machines, and equipment that could present a risk to life or property.3.Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVINGSERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USEWITHIN THE OVERALL EQUIPMENT OR SYSTEM.4.Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZEDVEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY SELLER.5.Programmable Products: Seller shall not be responsible for the Buyer's programming ofa programmable Product.1.Warranty: Seller's exclusive warranty is that the Products will be free from defects inmaterials and workmanship for a period of twelve months from the date of sale by Seller (or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE OF THE PRODUCTS.2.Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the formoriginally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an amount equal to the purchase price of the Product; provided that there shall be noliability for Seller or its affiliates unless Seller's analysis confirms that the Products were handled, stored, installed and maintained and not subject to contamination, abuse,misuse or inappropriate modification. Return of any Products by Buyer must beapproved in writing by Seller before shipment.3.Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FORSPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF THE PRODUCT ON WHICH LIABILITY IS ASSERTED.4.Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and itsemployees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products.1.Intellectual Property: The intellectual property embodied in the Products is the exclusiveproperty of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way without the written permission of Seller. Buyer (at its own expense) shall indemnify and hold harmless Seller and defend or settle any action brought against Seller to the extent that it is based on a claim that any Product made to Buyer specifications infringedintellectual property rights of another party.2.Property; Confidentiality: Notwithstanding any charges to Buyer for engineering ortooling, all engineering and tooling shall remain the exclusive property of Seller. All information and materials supplied by Seller to Buyer relating to the Products areconfidential and proprietary, and Buyer shall limit distribution thereof to its trustedemployees and strictly prevent disclosure to any third party.3.Performance Data: Performance data is provided as a guide in determining suitabilityand does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must correlate it to actual application requirements.4.Change In Specifications: Product specifications and description may be changed at anytime based on improvements or other reasons. It is Seller’s practice to change part numbers when published ratings or features are changed, or when significantengineering changes are made. However, some specifications of the Product may be changed without any notice.5.Errors And Omissions: The information on Seller’s website or in other documentationhas been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.6.Export Controls: Buyer shall comply with all applicable laws, regulations and licensesregarding (a) export of the Products or information provided by Seller; (b) sale ofProducts to forbidden or other proscribed persons or organizations; (c)disclosure to non-citizens of regulated technology or information.1.Waiver: No failure or delay by Seller in exercising any right and no course of dealingbetween Buyer and Seller shall operate as a waiver of rights by Seller.2.Assignment: Buyer may not assign its rights hereunder without Seller's written consent.w: These Terms are governed by Illinois law (without regard to conflict of laws). Federaland state courts in Illinois have exclusive jurisdiction for any dispute hereunder.4.Amendment: These Terms constitute the entire agreement between Buyer and Sellerrelating to the Products, and no provision may be changed or waived unless in writing signed by the parties.5.Severability: If any provision hereof is rendered ineffective or invalid, such provision shallnot invalidate any other provision.Certain Precautions on Specifications and UseOMRON ON-LINEGlobal - USA - Cat. No. J01C-E-01Printed in USAOMRON ELECTRONIC COMPONENTS LLC55 E. Commerce Drive, Suite B Schaumburg, IL 60173847-882-228801/07 Specifications subject to change without noticeComplete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at – under the “About Us” tab, in the Legal Matters section.ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.T o convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.。

商品选择......................160共通注意事项..................190技术指南......................467用语说明. (471)相关信息⏽数字温控器 基本型E5CN/E5CN-U(48×48mm)48mm见方的通用温控器经改良更新，功能/性能大大提升。

提高了指示精度，还新增了预防保护功能，产品进一步升级•指示精度 热电偶输入 ±0.3％PV(以往产品 ±0.5％PV) Pt输入 ±0.2％PV(以往产品 ±0.5％PV) 模拟量输入 ±0.2％FS(以往产品 ±0.5％FS)•将模拟量输入型和电流输出型作为新机型添加到E5CN-U型(插入型)中•添加PV/SV状态显示功能，温控器状态(自动/手动、RUN/STOP、报警发生)一目了然，可交替显示PV/SV•添加控制输出ON/OFF计数功能，可预防保护温控器内部继电器主要输入输出功能48×48mmE5CN 48×48mm E5CN-U关于操作请参阅第532页。

提供本手册作为产品选择的指南。

有关注意事项等使用时必须了解的内容，请务必阅读下列用户手册。

“E5CN/E5AN/E5EN型 数字温控器 用户手册”“E5CN/E5AN/E5EN型 数字温控器 通信手册”PDF版用户手册可从以下网站下载。

E5CN/E5CN-U⏽产品系列注.1点控制输出型(1点、2点辅助输出)或2点控制输出型可以用于加热/冷却控制。

型号结构型号标准E5CN-□□□□□□□□-□-□──────────①②③④⑤⑥⑦⑧⑨⑩注.并非所有按上述型号标准构成的机型均可制造。

订购时请参考“种类”(235～241页)进行选择。

*1.辅助输出是指可输出报警或简易运算结果的触点输出。

*2.高寿命继电器输出在闭路、断路时通过三端双向开关进行开闭，因此连接DC负载时输出不能OFF。

欧姆龙电子温控器常见问题温控器选型要素有那些？：①外型大小：一般为面板尺寸，开孔尺寸略小以E5□N为例：□中A表示面板尺寸为96×96 mm；开孔尺寸为92×92mmB表示面板尺寸为72×72 mm；开孔尺寸为68×68mm C表示面板尺寸为48×48 mm；开孔尺寸为45×45mm E表示面板尺寸为48×96 mm；开孔尺寸为45×92mm G表示面板尺寸为48×24mm；开孔尺寸为45×22.2mm ②输入类型：铂电阻，热电偶，热敏电阻，模拟量信号（4－20mA，0－10V等）③输出类型：继电器，SSR，集电极，电压（DC12V/24V），线性模拟量（4－20mA，0－10V等）④报警点个数⑤是否需要其他功能：通讯、事件输入、传送输出⑥安装方式：面板安装、导轨安装EJ1和G3ZA进行通讯，但是CX-THERMO无法识别G3ZA是为什么？：请按照如下5步操作：①EJ1的SW2-7开关要设置成ON；②通讯电缆是否使用EJ1C-CBLA050；③G3ZA的SW2设置成3；④CX-THERMO里面要先执行“RESET UNITCONFIG URATION”,然后再“SOFTWARE RESET”；温控器一上电℃闪烁，这是什么原因？如何消除？：主要是因为以下原因：①温控器使用了PID控制标准控制，并且ST功能设置为On了；以下情况会ST整定a．当前值和设定值的差值超出ST稳定状态范围；b．温控器断电上电。

可以采取以下方案：②如果不想PID参数因为现场环境值和设定值变化而变化的话，在初始菜单中，将ST置为Off即可；③到高级功能菜单里面把ST稳定状态范围调节到客户要求范围内。

温控器有的菜单选不到，是怎么回事？：主要有以下几种原因：①是否设置了菜单保护；②相应功能是否使能，例如：P,I,D三个参数一定要设置成PID控制才能选到；③相应功能硬件是否配置，例如：通讯菜单一定要配置了通讯模块才能选到；④使用的是E5_N（第二代、第三代）或者是E5_R的温控器。

OMRON温控仪参数设定方法OMRON E5CN 温控表参数设定方法仪面板（E5CN ）如图：一．参数设置等级操作：1. 按“”键3秒以上，进入参数设置等级。

显示：2. 按“”键，切换参数代码，可循环显示。

显示：3. 按“”或“”键，修改参数设定值。

4. 按“”键3秒以上，返回正常控制模式。

显示：二．报警值设置操作：1. 按“”键，进报警值设定，可循环显示。

显示：温度实际值设定值向上向模式等级状态2.按“”键，设定报警1（）温度值。

显示：3.按“”或“”键，修改报警输出设定值。

4.按“”键，设定报警2（）温度值。

显示：5.按“”或“”键，修改报警输出设定值。

6.按“”键，返回正常控制模式。

显示：三．自整定操作：按“”键，进入自整定设置操作。

显示：按“”键，将“”改为“”。

显示：按“”键，开始自整定，设定温度值闪烁显示。

显示：注意：此操作应在参数全部设定完成后，加热到实际温度与设定温度值基本相同后开始，否则，自整定结果不准确，在此过程中，禁止对温控表进行其他操作，实际温度值会有较大波动，属正常现象，待设定值停止闪烁后，自整定即完成，自动恢复正常控制模式。

四．参数功能及设定值：按“”键3秒以上参数功能设定值温度传感器输入型号0：代表传感器型号pt100按“”键温度显示单位C：代表摄式度；F：代表华式度按“”键最高上限温度报警值高于正常设定值20%-25%此值到达温控器停止输出并报警按“”键最低下限温度报警值按“”键PID控制*关键参数，禁止随意修改*PID：自动控制方式；ONOFF：开关控制方式按“”键温度控制方式Stnd：标准控制；H-C：热或冷控制按“”键自整定功能开关ON：开；OFF：关按“”键控制周期2：加热周期为2秒钟*关键参数，禁止随意修改*按“”键控制方向OR-r:加热；OR-d:冷却按“”键报警方式1类型8：温度上限值报警*除杀菌温度外，其他可不设定*按“”键报警方式2类型8：温度上限值报警*关键参数，禁止随意修改*按“”键3秒以上，返回正常控制模式。

OMRON温控仪参数设定方法
首先，打开OMRON温控仪的电源，并确保温控仪处于停止状态。

1.设定温度范围：
根据实际需求，在控制面板上选择温度范围。

通常情况下，温控仪可以设置的温度范围为0-400℃，可以通过操作键或旋钮进行设定。

2.设定控制模式：
3.设定控制参数：
在PID控制模式下，需要设定三个参数：比例系数（P）、积分时间（I）和微分时间（D）。

这些参数的设定需要依据所控制的温度系统的特性进行调整。

一般情况下，先设定P值，然后根据调节机制对I和D进行适当的调整。

参数设定过程中可以通过观察实际温度和设定温度的变化来进行优化。

4.设定报警功能：
5.设定通信功能：
部分OMRON温控仪支持通信功能，可以通过RS485、RS232等接口与其他设备进行数据交换和远程监控。

如果需要使用通信功能，需要按照温控仪的说明文档设置通信参数，例如波特率、数据格式等。

6.设定阻抗检测功能：
7.设定其他功能：
在所有参数设定完成后，按照操作说明将设定的参数保存并生效。

之后，OMRON温控仪即会按照所设定的参数进行控制。

需要注意的是，不同型号和版本的OMRON温控仪的参数设定方法可能会有所不同，因此在进行参数设定之前，应仔细阅读设备的使用手册和技术说明书，并按照说明进行操作。

此外，由于温度参数设定涉及到实际工业控制系统，建议在设定之前进行充分的调试和测试，以确保设定的参数能够有效控制温度系统。

omron传感器工作原理Omron传感器是工业自动化领域中的一种重要设备，它们被广泛应用于各种工业应用中，如机器人、自动化生产线、安全控制等。

Omron传感器的工作原理是什么？本文将详细介绍Omron传感器的工作原理，帮助读者更好地理解其工作特性。

一、什么是Omron传感器？Omron传感器是日本Omron公司生产的各种类型传感器，包括光电传感器、距离传感器、压力传感器、温度传感器等。

这些传感器具有不同的功能和应用范围，被广泛应用于各种工业设备和系统中。

1. 光电传感器：光电传感器是基于光电效应工作的。

它包括一个光源（如发光二极管）和一个光接收器（如光敏电阻）。

当光源发出光时，光线会照射到光接收器上，导致其电阻值发生变化，从而产生一个电信号。

根据电阻值的变化，光电传感器可以检测物体的存在、移动或颜色等。

2. 距离传感器：距离传感器基于超声波或激光测距原理。

它通过发出超声波或激光光束，测量反射时间或光程来计算物体之间的距离。

距离传感器可以用于控制自动对焦、调节屏幕亮度、检测物体移动等。

3. 压力传感器：压力传感器通过测量物体施加在传感器上的压力来工作。

它们通常使用应变片或压电材料来感应压力，并将压力转换为电信号。

压力传感器可以用于测量气体或液体的压力、温度和粘度等。

4. 温度传感器：温度传感器通过测量物体的温度来工作。

它们通常使用热电偶、热电阻或半导体材料来感应温度变化，并将温度转换为电信号。

温度传感器可以用于控制系统温度、检测过热等。

三、Omron传感器的应用1. 机器人控制：Omron传感器被广泛应用于机器人控制中，如视觉传感器用于识别物体、距离传感器用于避障等。

这些传感器使得机器人能够更加智能和灵活地执行任务。

2. 自动化生产线：Omron传感器被广泛应用于自动化生产线中，如光电传感器用于检测物体的位置和颜色、压力传感器用于控制生产线的速度等。

3. 安全控制：Omron传感器也被广泛应用于安全控制中，如温度传感器用于检测过热、烟雾探测器用于检测烟雾和气体等。

MEMS Thermal SensorsD6TContactless measurementcreating energy-efficient and comfortable living spacesMEMS Thermal Sensors D6THigh Accuracy, Smaller Footprint, East to Work WithOMRON's unique MEMS technology allows combining thermopile elements and ASICs into one package resulting to ultra-compact footprint.Infrared rayAchieving the highest level of SNR* in the world ** SNR: Signal-to-Noise Ratio. Compares the level of a signal to the level of background noise *2 As of December 2017, according to OMRON researchConverts sensor signal to digital temperature output allowing easy use of microcontrollerSpace-saving design,well-suited for embedded applicationsEasy connectionCompact sizeSilicon lens far-infrared focusingDetection principleThermopileHot junctionInfrared ray Cold junctionMEMS Thermal (IR* sensor) measures the surface temperature of objects without touching them when the thermopile element absorbs the amount of radiant energy from the object.*IR: Infrared RayLow noiseCross-section view of D6T sensorThe sensor utilizes the seebeck effect in which thermoelectric force is generated due to the temperature difference that occurs 3Detection results of temperature distribution5MEMS Thermal Sensors D6TObject DetectionD6T sensors can detect objects by pinpointing the target object temperature.6D6T sensor meets customer needs byproviding a wide range of application support from home appliances to industrial use.D6T sensors let you measure temperature without the need to physically touch the object.This allows measuring temperature where it was not possible for contact thermal sensors due to space shortage.The sensors can be used in a wide range of applications including FEMS (Factory EnergyManagement System).7MEMS Thermal Sensors D6TComparison with Pyroelectric SensorAble to detect human (object) motionUnable to detect stationary human (object) presenceAble to detect human (object) motionAble to detect both stationary and motion state of humans (objects).Both the pyroelectric sensor and non-contact MEMS thermal sensor can detect even the slightest amount of radiant energy from objects such as infrared radiation and convert them into temperaturereadings. However, unlike pyroelectric sensor that relies on motion detection, non-contact MEMS thermal sensor is able to detect the presence of stationary humans (or objects).Converts temperature readings only when detecting “temperature changes in the radiant energy” in its field of view.Converts temperature readings by “continuously detecting the temperature of radiant energy” in its field of view8X = 58.0°Y = 58.0°X = 111cmY = 111cmX = 222cmY = 222cmX = 333cmY = 333cmX = 47cmY = 47cmX = 94cmY = 94cmX = 141cmY = 141cmX = 103cmY = 10cmX = 206cmY = 20cmX = 309cmY = 30cmX = 81cmY = 84cmX = 162cmY = 169cmX = 244cmY = 253cmX = 200cmY = 200cmX = 400cmY = 400cmX = 600cmY = 600cm1(1x1)8(1x8)16(4x4)X = 26.5°Y = 26.5°X = 54.5°Y = 5.5°X=44.2°Y=45.7°1024(32x32)X=90.0°Y=90.0°Viewing Angle and Measurement AreaChoose your preferred sensor viewing angle to meet your application needs.* The sizes of measurement area indicated above are for reference only.* The size of measurement area changes according to sensor mounting angle.DistanceNumber ofelementsAppearanceSize ofmeasurementareaDistance 1mDistance 2mDistance 3mNumber ofelementsX-directionY-directionDistance Distance Distance910D 6THigh Sensitivity Enables Detection of Stationary Human Presence•OMRON’s unique MEMS and ASIC technology achieve a high SNR.•Superior noise immunity with a digital output.•High-precision area temperature detection with low cross-talk field of view characteristics.Ordering InformationThermal SensorsAccessories (Sold separately)Model Number Legend(1) Number of elements 44L : 16 (4 ✕ 4)8L : 8 (1 ✕ 8)1A : 1 (1 ✕ 1)32L : 1024 (32 ✕ 32)(2) Viewing angle06: X direction=44.2°, Y direction=45.7°09: X direction=54.5°, Y direction=5.5°01: X direction, Y direction=58.0°02: X direction, Y direction=26.5°01A : X direction, Y direction=90.0°(3) Special Functions H : High-temperature type Non-display : Standard sensorRoHS CompliantRefer to Safety Precautions on page 17.Type Model Cable HarnessD6T-HARNESS-0211D6TMEMS Thermal SensorsD 6TRatings, Specifications, and FunctionsRatingsCharacteristicsFunctions*1.Refer to Field of View Characteristics .*2.Refer to Object Temperature Detection Range .*3.Reference data*4.Taken to be the average value of the central 4 pixels.ItemModelD6T-44L-06/06HD6T-8L-09/09HD6T-1A-01D6T-1A-02D6T-32L-01A Power supply voltage 4.5 to 5.5 VDC Storage temperature range -10 to 60°C -20 to 80°C-20 to 80°C-40 to 80°C -20 to 80°C (with no icing or condensation)Operating temperature range 0 to 50°C 0 to 60°C 0 to 60°C-40 to 80°C -10 to 70°C (with no icing or condensation)Storage humidity range 85% max.95% max.95% max.95% max.95% max.(with no icing or condensation)Operating humidity range20% to 85%20% to 95%20% to 95%20% to 95%20% to 95%(with no icing or condensation)Item Model D6T-44L-06/06H D6T-8L-09/09H D6T-1A-01D6T-1A-02D6T-32L-01AView angle *1X direction 44.2°54.5°58.0°26.5°90°Y direction45.7°5.5°58.0°26.5°90°Object temperature output accuracy *2Accuracy 1±1.5°C max.Measurement conditions: Vcc = 5.0 V (1) Tx = 25°C, Ta = 25°C (2) Tx = 45°C, Ta = 25°C (3) Tx = 45°C, Ta = 45°CWithin ±3.0°CMeasurementconditions: Vcc = 5.0 V Tx = 25°C, Ta = 25°C Central 16-pixel area Accuracy 2±3.0°C max.Measurement conditions: Vcc = 5.0 V (4) Tx = 25°C, Ta = 45°C Within ±5.0°C Measurementconditions: Vcc = 5.0 V Tx = 80°C, Ta = 25°C Central 16-pixel areaCurrent consumption5 mA typical3.5 mA typical19 mA typicalItemModelD6T-44L-06/06H D6T-8L-09/09H D6T-1A-01D6T-1A-02D6T-32L-01A Object temperature detection range *25 to 50°C/5 to 200°C 5 to 50°C/5 to 200°C 5 to 50°C -40 to 80°C 0 to 200°C Reference temperature detection range *25 to 45°C5 to 45°C5 to 45°C-40 to 80°C0 to 80°COutput specifications Digital values that correspond to the object temperature (Tx) and reference temperature(Ta) are output from a serial communications port.Output formBinary code (10 times the detected temperature (°C))Communications formI2C compliant Temperature resolution (NETD) *30.06°C0.03°C0.02°C0.06°C0.33°C *412D6TMEMS Thermal SensorsD 6TObject Temperature Detection RangeD6T-44L-06, D6T-8L-09, D6T-1A-01D6T-44L-06H, D6T-8L-09HD6T-1A-02D6T-32L-01AConnectionsThermal Sensor Configuration Diagram<D6T-8L-09/09H>Note:The D6T-44L-06/06H has pixels 0 to 15.The D6T-1A-01/02 has pixel 0.The D6T-32L-01A has pixel 0 to 1023.Terminal Arrangement: Object temperature detection range5101520253035404550-10020406080100120140160180200Object temperature Tx (°C)R e f e r e n c e t e m p e r a t u r e T a (°C )Object temperature Tx (°C)R e f e r e n c e t e m p e r a t u r e Ta (°C ): Object temperature detection range-10102030405060708090-10020406080100120140160180200Terminal NameFunctionRemarks1GND Ground2VCC Positive power supply voltage input 3SDA Serial data I/O line Connect the open-drain SDA terminal to a pull-up resistor.4SCLSerial clock inputConnect the open-drain SCL terminal to a pull-up resistor.13D6TMEMS Thermal SensorsD 6TField of View CharacteristicsD6T-44L-06/06HField of view in X Directionence, the angular range where the Sensor output is 50% or higher whenthe angle of the Sensor is changed is defined as the view angle.X directionY direction++−−P0P4P1 P5P2 P6P3P7D6T-8L-09/09HField of view in X DirectionField of view in Y DirectionDetection Area for Each PixelNote:Definition of view angle: Using the maximum Sensor output as a refer-ence, the angular range where the Sensor output is 50% or higher whenthe angle of the Sensor is changed is defined as the view angle.14D6TMEMS Thermal SensorsD 6TD6T-1A-01Field of view in X DirectionField of view in Y DirectionDetection Area for Each PixelD6T-1A-02Field of view in X DirectionField of view in Y DirectionNote:Definition of view angle: Using the maximum Sensor output as a refer-ence, the angular range where the Sensor output is 50% or higher when the angle of the Sensor is changed is defined as the view angle.D6T-32L-01AField of view in X DirectionField of view in Y DirectionDetection Area for Each PixelNote:Definition of view angle: Using the maximum Sensor output as a refer-ence, the angular range where the Sensor output is 50% or higher when the angle of the Sensor is changed is defined as the view angle.15D6TMEMS Thermal SensorsD 6TDimensions (Unit: mm)Note:Unless otherwise specified, a tolerance of ±0.3 mm applies to all dimensions.D6T-44L-06/06HSupporting and Mounting Area (Shaded Portion)Top ViewNote:Due to insulation distance limitations, donot allow metal parts to come into contactwith the Sensor.D6T-8L-09/09HSupporting and Mounting Area (Shaded Portion)Note:Due to insulation distance limitations, donot allow metal parts to come into contact with the Sensor.16D6TMEMS Thermal SensorsD 6TD6T-1A-01/02Supporting and Mounting Area (Shaded Portion)Top Viewmetal parts to come into contact with the Sensor.17D6TMEMS Thermal SensorsD 6TSafety Precautions●Installation•The Sensor may not achieve the characteristics given in this datasheet due to the ambient environment or installation loca-tion. Before using the Sensor, please acquire an adequate understanding and make a prior assessment of Sensor char-acteristics in your actual system.●Operating Environment•Do not use the Sensor in locations where dust, dirt, oil, and other foreign matter will adhere to the lens. This may prevent correct temperature measurements.•Do not use the Sensor in any of the following locations.•Locations where the Sensor may come into contact with water or oil •Outdoors•Locations subject to direct sunlight.•Locations subject to corrosive gases (in particular, chlo-ride, sulfide, or ammonia gases).•Locations subject to extreme temperature changes •Locations subject to icing or condensation.•Locations subject to excessive vibration or shock.●Noise Countermeasures•The Sensor does not contain any protective circuits. Never subject it to an electrical load that exceeds the absolute maxi-mum ratings for even an instance. The circuits may be dam-aged. Install protective circuits as required so that the absolute maximum ratings are not exceeded.•Keep as much space as possible between the Sensor anddevices that generates high frequencies (such as high-frequency welders and high-frequency sewing machines) or surges.•Attach a surge protector or noise filter on nearby noise-generating devices (in particular, motors, transformers, solenoids, magnetic coils, or devices that have an inductance component).•In order to prevent inductive noise, separate the connector of the Sensor from power lines carrying high voltages or large currents. Using a shielded line is also effective.•If a switching requlator is used, check that malfunctions will not occur due to switching noise from the power supply.●Handling•This Sensor is a precision device. Do not drop it or subject it to excessive shock or force. Doing so may damage the Sensor or change its characteristics. Never subject the connector to unnecessary force. Do not use a Sensor that has been dropped.•Take countermeasures against static electricity before you handle the Sensor.•Turn OFF the power supply to the system before you install the Sensor. Working with the Sensor while the power supply is turned ON may cause malfunctions.•Secure the Sensor firmly so that the optical axis does not move.•Install the Sensor on a flat surface. If the installation surface is not even, the Sensor may be deformed, preventing correct measurements.•Do not install the Sensor with screws. Screws may cause the resist to peel from the board. Secure the Sensor in a way that will not cause the resist to peel.•Always check operation after you install the Sensor.•Use the specified connector (GHR-04 from JST) and connect it securely so that it will not come off. If you solder directly to the connector terminals, the Sensor may be damaged.•Make sure to wire the polarity of the terminals correctly. Incor-rect polarity may damage the Sensor.•Never attempt to disassemble the Sensor.•Do not use the cable harness to the other product.Precautions for Correct Use18Terms and Conditions AgreementRead and understand this catalog.Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments.Warranties.(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanshipfor a period of twelve months from the date of sale by Omron (or such other period expressed in writingby Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUTNON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A P ARTICULAR PURPOSE OF THEPRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILLSUITABL Y MEET THE REQUIREMENTS OF THEIR INTENDED USE.Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) thenon-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase priceof the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty.See /global/ or contact your Omron representative for published information.Limitation on Liability; Etc.OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.Suitability of Use.Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicablethird party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product withrespect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.NEVER USE THE PRODUCT FOR AN APPLICA TION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERL Y RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.Programmable Products.Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.Performance Data.Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.Change in Specifications.Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practiceto change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product.Errors and Omissions.Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.19• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms.OMRON CorporationElectronic and Mechanical Components CompanyRegional ContactCat. No. A274-E1-020519(0318)Americas Europehttps:/// http://components.omron.eu/ Asia-Paci ic China https://.sg/ https:///Korea Japanhttps://www.omron-ecb.co.kr/ https://www.omron.co.jp/ecb/In the interest of product improvement, specifications are subject to change without notice.© OMRON Corporation 2018-2019 All Rights Reserved.。

1、日本(OMRON)欧姆龙OMRON欧姆龙集团始创于1933年，目前拥有近87年历史。

现有员工32583人，全球营业额6272亿日元，产品品种达几十万种，涉及工业自动化控制系统、电子元器件、汽车电子、社会系统以及健康医疗设备等广泛领域。

为了适应时代的发展，在公司成立50周年纪念时，公司名称与品牌名称实现了统一，改为“欧姆龙集团(株式会社)”。

创造社会需求，构筑“安心”，“安全”，“环保”“健康”的社会，是欧姆龙集团的发展目标。

2、德国(KROHNE)科隆德国KROHNE公司一直是国际测量领域的先驱，拥有先进技术和丰富的应用经验，使其能够根据市场的要求不断创新，从而提供给全球用户可靠、便捷、先进的测量仪器。

近百年来，KROHNE所研发的一系列新产品，不仅创造出多项世界第一，而且还成为测量领域里的标竿，引导着全球测量仪器的变革和发展。

3、美国(banner)邦纳BANNER始建于1966年，目前有54周年历史。

总部位于美国的明尼苏达州，是全球顶尖的自动化技术专家和整体解决方案提供者。

公司拥有22,000多种产品，具有最为齐全的产品线，经过40多年的发展，现已成为全球最大的光电传感器、测量检测、视觉传感器和机床安全产品的专业制造商之一。

丰富完整的产品选择、迅速的交货期、强大的技术支持以及同行业中首屈一指的研发能力保证了BANNER在同行业中的领军地位。

4、德国(IFM)易福门IFM是德国的一个工控品牌。

1969年德国易福门IFM这家家族企业发明了基于薄膜技术的电感式接近传感器，经过51年的发展从此走上了成功的道路。

今天，“efector”品牌成为了位置与流体传感器、物体识别、诊断和识别系统的代名词，而“ecomat”品牌则是网络和控制系统的杰出结果公司在全球70多个国家拥有5200多名员工，主要为机械制造等行业提供研发和销售服务，用户超过约10万家。

5、瑞士(ABB)ABB是电力和自动化技术领域的全球领导厂商，ABB集团位列全球500强企业。

OMRON温控仪参数设定方法步骤一：了解OMRON温控仪的基本菜单1.“设置”选项：用于设定基本参数和通信设置。

2.“输入”选项：用于设定输入信号类型和测量范围。

3.“输出”选项：用于设定输出信号类型和控制模式。

4.“报警”选项：用于设定报警方式和阈值。

步骤二：设定基本参数在“设置”菜单中，您可以设定一些基本参数，如时间、日期、单位和显示方式等。

这些参数对于正确的温度控制非常重要。

确保您根据您的应用需求正确设定这些参数。

步骤三：设定输入参数在“输入”菜单中，您可以设定温度传感器类型和测量范围。

确保您选择适合您应用的传感器类型，并根据测量物体的温度范围设置测量范围。

如需设定多个输入信号，请重复此步骤。

步骤四：设定输出参数在“输出”菜单中，您可以设定输出信号类型和控制模式。

根据您的设备和应用要求，选择适合的输出信号类型（如电压、电流或继电器）和控制模式（如PID、ON/OFF或时间比例控制）。

确保正确设定输出参数以实现准确的温度控制。

步骤五：设定报警参数在“报警”菜单中，您可以设定报警方式和阈值。

您可以选择报警器类型（如声音或光指示）和报警阈值（如高温或低温）。

确保您根据应用需求适当设定报警参数以确保及时发现温度异常情况。

步骤六：保存和应用参数设定在完成所有参数设定后，确保您保存设置以保证以后能正确应用这些参数。

通常，您可以在“设置”菜单中找到“保存”或“应用”选项。

选择该选项以将参数设定保存到设备中。

步骤七：验证和调整参数设定在正式应用参数设定之前，建议您验证设置的正确性。

将温控仪连接到目标系统并获取实时温度数据。

验证您设置的传感器、控制模式、输出类型和报警参数是否能正确工作。

如果发现问题，您可以返回相应的菜单选项进行调整。

步骤八：常规维护和调整总结：OMRON温控仪具有广泛应用的智能温度控制设备。

通过了解设备的基本菜单选项，正确设定基本参数、输入参数、输出参数和报警参数，您可以实现准确、稳定的温度控制。

欧姆龙pt100选型手册欧姆龙（Omron）是一家全球领先的自动化控制解决方案提供商，其产品广泛应用于工业自动化、医疗设备、家用电器等领域。

其中，欧姆龙PT100温度传感器是一款常用的温度测量设备，本文将为大家介绍欧姆龙PT100选型手册。

一、欧姆龙PT100温度传感器简介欧姆龙PT100温度传感器是一种基于铂电阻原理的温度测量设备，其测量范围通常为-200℃至+600℃。

该传感器具有高精度、稳定性好、抗干扰能力强等特点，广泛应用于工业自动化领域。

二、欧姆龙PT100选型手册内容1. 产品概述：介绍欧姆龙PT100温度传感器的基本参数和特点，包括测量范围、精度、响应时间等。

2. 选型指南：根据不同的应用场景和需求，提供不同型号的PT100传感器的选型建议。

例如，对于高温环境下的应用，建议选择耐高温型PT100传感器；对于需要长期稳定性的应用，建议选择精度高、稳定性好的PT100传感器。

3. 安装指南：介绍PT100传感器的安装方法和注意事项。

包括传感器的安装位置、固定方式、接线方法等。

同时，还提供了一些常见问题的解决方案，帮助用户更好地使用PT100传感器。

4. 技术参数：详细列出了各个型号PT100传感器的技术参数，包括测量范围、精度、响应时间、线性度等。

用户可以根据自己的需求选择合适的型号。

5. 应用案例：提供一些典型的应用案例，展示PT100传感器在不同领域的应用。

例如，工业自动化领域的温度控制、医疗设备领域的体温测量等。

6. 常见问题解答：总结了用户在使用PT100传感器过程中常遇到的问题，并提供了相应的解决方案。

例如，传感器输出信号异常、温度测量不准确等问题的解决方法。

三、欧姆龙PT100选型手册的意义欧姆龙PT100选型手册的发布，对于用户选择合适的PT100传感器具有重要意义。

首先，手册提供了详细的产品参数和技术指标，用户可以根据自己的需求选择合适的型号。

其次，手册提供了安装指南和常见问题解答，帮助用户更好地使用和维护PT100传感器。

OMRON温控器E5CZ调整方法1.前期准备：首先，确保温控器的电源和控制回路断开，防止发生电击事故。

请关闭电源开关，并使用绝缘胶带遮盖其中一侧的端子。

2.连接温度传感器：根据需要检测的温度范围，选择合适的温度传感器，并将其连接到E5CZ的终端4和终端5上。

请注意，如需使用传感器电源时，请将终端5连接到E5CZ的终端2上。

3.设置标定温度：标定温度是控制温度的基准值，根据实际需要设置。

将标定温度设定为所需的温度，按住“set”按钮约2秒，然后进入标定温度设定模式。

4.调整比例系数（比例控制）：在比例控制模式下，E5CZ会根据偏差进行温度控制。

比例系数影响控制器的响应速度和稳定性。

调整步骤如下：a.通过按下“↑”或“↓”按钮进入设定模式。

b. 按住“set”按钮约2秒，进入PID设定模式。

c.按下“→”按钮显示比例系数（P）。

d.使用“↑”或“↓”调整比例系数的值。

较大的比例系数将使控制器对温度的变化更敏感，但也会导致较大的震荡。

5.调整积分时间（积分控制）：在积分控制模式下，E5CZ会根据偏差的积分值进行温度控制。

调整步骤如下：a.通过按下“↑”或“↓”按钮进入设定模式。

b. 按住“set”按钮约2秒，进入PID设定模式。

c.按下“→”按钮显示积分时间（I）。

d.使用“↑”或“↓”调整积分时间的值。

较大的积分时间将使控制器对温度的累积误差有更高的响应，但也可能导致较长的超调时间。

6.调整微分时间（微分控制）：在微分控制模式下，E5CZ会根据偏差的变化率进行温度控制。

调整步骤如下：a.通过按下“↑”或“↓”按钮进入设定模式。

b. 按住“set”按钮约2秒，进入PID设定模式。

c.按下“→”按钮显示微分时间（D）。

d.使用“↑”或“↓”调整微分时间的值。

较大的微分时间将导致控制器对温度变化率更敏感，但可能会增加震荡。

7.调整输出限制（输出限制）：输出限制功能可以调整PWM输出的幅度范围，以控制加热或冷却元件的功率。