DIN571六角头木螺钉

钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8 公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

1、公制计量：（10进制）1m =100 cm=1000 mm2、英制计量：（8进制）1英寸=8英分1英寸=25.4 mm 3/8¢¢×25.4 =9.523、1/4¢¢以下的产品用番号来表示其称呼径，如：4#，5#，6#，7#，8#，10#，12#螺纹一、螺纹是一种在固体外表面或内表面的截面上，有均匀螺旋线凸起的形状。

德国标准1997年1月铁路车辆用螺栓、螺钉和螺母一览表DIN 25200ICS 21.060.10; 21.060.20 替换1986年11月的版本主题词：铁路车辆、螺栓（螺钉）、螺母、连接件前言本标准由FB1“部件、半成品和基本准则”委员会下属的AA 1.1“连接件”工作委员会制定。

这次新版对1986年11月的版本做了大规模的修改，因为过渡到欧洲标准需要取消各个成员国的国家标准。

只要在编辑定稿日期之前这些被取消的标准仍然有效，相应的欧洲标准也做了引用。

因为根据“连接件方面的国际标准作为欧洲标准制定”这一原则性规定，另外需要制定相应的DIN/ISO标准。

除尺寸上个别方面需要调适外，采用了DIN ISO 272规定的扳手开口度（例外情况：DIN 571——六角木螺钉和DIN 929——六角焊接螺母）。

附录A和B都是资料性附录。

修改与1986年11月的版本相比，这次版本做了下列修改：a) 取消了以下标准而没有制定相应的替代标准：DIN 558、DIN 601、DIN 917、DIN 935、DIN 970、DIN 971-2、DIN 972、DIN 979和DIN 5586。

b) 用DIN-EN-或DIN-ISO-标准替换了以下标准：DIN 439-2、DIN 931、DIN 933、DIN 934、DIN 960、DIN 961、DIN 965、DIN 966、DIN 971-1、DIN 7881、DIN 7982、DIN 7983和DIN 7985。

c) 引用了下列标准：DIN 24014、DIN EN 24017、DIN EN 24032、DIN 24035、DIN EN 28673、DIN EN 28675、DIN EN 28676、DIN EN 28765、DIN EN ISO 7045、DIN EN ISO 7046-2、DIN EN ISO 7047、DIN ISO 7049、DIN ISO 7050和DIN ISO 7051。

常用螺栓的标准及规格表国家标准规定了螺纹规格为M3~M64,A和B级的六角头螺栓.A级用于D<=24和L<=10D或L<=150mm(按较小值)的螺栓;B级用于D>24或L>10D或L>150(按较小值)的螺栓外六角螺栓尺寸规格(如图)钢构造连接用螺栓性能等级分、、、、、、、、等10余个等级，其中级及以上螺栓材质为低碳合金钢或中碳钢并经热处理〔淬火、回火〕，通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两局部数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为；3、螺栓材质的公称屈从强度达400×0.6=240MPa级性能等级级高强度螺栓，其材料经过热处理后，能到达：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为；3、螺栓材质的公称屈从强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，一样性能等级的螺栓，不管其材料和产地的区别，其性能是一样的，设计上只选用性能等级即可。

常用螺丝规格表强度等级所谓级和级，是指螺栓的抗剪切应力等级为和10.9Gpa ，8.8 公称抗拉强度800N/MM2 公称屈从强度640N/MM2一般的螺栓是用"X.Y"表示强度的，，X*100=此螺栓的抗拉强度，，X*100*〔Y/10〕=此螺栓的屈从强度〔因为按标识规定：屈从强度/抗拉强度=Y/10〕。

如级那么此螺栓的抗拉强度为：400MPa 屈从强度为：400*8/10=320MPa另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米〔m〕、厘米〔cm〕、毫米〔mm〕等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸〔inch〕，相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

1、公制计量：（10进制）1m =100 cm=1000 mm2、英制计量：（8进制）1英寸=8英分 1英寸=25.4 mm 3/8￠￠×25.4 =9.523、1/4￠￠以下的产品用番号来表示其称呼径，如：4#， 5#， 6#， 7#， 8#， 10#， 12#螺纹一、螺纹是一种在固体外表面或内表面的截面上，有均匀螺旋线凸起的形状。

螺栓性能等级的含义默认分类2009-10-23 15:06 阅读440 评论0 字号：大大中中小小钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8 公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

常用螺栓的标准及规格表国家标准规定了螺纹规格为 M3~M64,A 和 B 级的六角头螺栓 .A 级用于D<=24 和 L<=10D或 L<=150mm(按较小值 )的螺栓 ;B 级用于 D>24 或 L>10D 或L>150(按较小值 )的螺栓外六角螺栓尺寸规格(如图 )钢构造连结用螺栓性能等级分、、、、、、、、等10 余个等级，此中级及以上螺栓材质为低碳合金钢或中碳钢并经热办理（淬火、回火），通称为高强度螺栓，其他通称为一般螺栓。

螺栓性能等级标号有两部分数字构成，分别表示螺栓资料的公称抗拉强度值和屈强比值。

比如，性能等级级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa 级；2、螺栓材质的屈强比值为；3、螺栓材质的公称折服强度达 400 × =240MPa级性能等级级高强度螺栓，其资料经过热办理后，能达到：1、螺栓材质公称抗拉强度达1000MPa 级；2、螺栓材质的屈强比值为；3、螺栓材质的公称折服强度达1000 × =900MPa级螺栓性能等级的含义是国际通用的标准，同样性能等级的螺栓，不论其资料和产地的区别，其性能是同样的，设计上只采纳性能等级即可。

常用螺丝规格表类规成品外径线径牙距别格最大最小±国标粗牙60°M10M11M12M14M16M18M20国标M10细牙 M1060°M12M12M14M16M18M20类别英制粗牙55°美制粗牙60°美制粗牙60°牙规数格(每英寸)1/8 405/32 323/16 241/4 205/16 183/8 167/16 141/2 129/16 125/8114#405#406#328# 32 10#24 12# 241/4 205/16 183/8 167/16 141/2 139/16 125/8114#485#446#408# 36 10#32 12# 281/4 285/16 243/8 247/16 201/2 209/16 185/818成品外径线径最大最小±成品外径线径类规牙数或牙别格最小±最大数国标7660°232日32制28A24牙18铁16铁14钉1260°10940日32制28AB24牙20铁18铁16钉1660°1412日制木螺2丝60°类别美制铁板 A牙60°美制铁板AB牙60°墙板钉细牙60°墙板钉粗牙60°德标( C/B)钉40°牙成品外径线径规数或格最大最小±牙数2#323#284#245#206#187#168#159#1410#1212#1114#102#323#284#245#206#207#198#1810#1612#141/4146#177#168#1510#126#97#98#910#82强度等级所谓级和级是指螺栓的抗剪切应力等级为和公称抗拉强度800N/MM2 公称折服强度640N/MM2一般的螺栓是用"" 表示强度的，X*100=此螺栓的抗拉强度，X*100* （ Y/10） =此螺栓的折服强度（由于按表记规定：折服强度/ 抗拉强度 =Y/10）===============如级则此螺栓的抗拉强度为： 400MPa折服强度为： 400*8/10=320MPa=================另：不锈钢螺栓往常标为A4-70， A2-70 的样子，意义还有解说胸怀现在世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（ cm）、毫米（ mm ）等，在欧州、我国及日本等东南亚地域使用许多，另一种为英制，计量单位主要为英寸（ inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用许多。

序号中文品名德国标准DIN中国标准GB国际标准ISO英文品名1自攻自钻螺钉多种头型DIN7504GB15856.1-4Self-drilling tapping screws2平垫DIN125-A GB97.1-85ISO7089Plain washers3平垫（带倒角）DIN125-B GB97.2-85ISO7090Mediun washers4平垫DIN126ISO7091Plain washers5重型弹垫DIN127-A GB7244Spring lock washers,tang ends 6标准弹垫DIN127-B GB93-87Spring lock washers,square ends 7内六角扳手DIN911ISO2936Socket wrenches8内六角圆柱头螺钉DIN912GB70-85ISO4762Hexagon socket cap screws9内六角平端紧定螺钉DIN913GB77-85ISO4026Hexagon socket set screws with falt point10内六角尖端紧定螺钉DIN914GB78-85ISO4027Hexagon socket set screws with cone point11内六角圆柱端紧定螺钉DIN915GB79-85ISO4028Hexagon socket set screws with dog point12内六角凹端紧定螺钉DIN916GB80-85ISO4029Hexagon socket set screws with cup point13六角头螺栓）（半牙）DIN931GB5782-86ISO4014Hexagon head screws 14六角头螺栓（全牙）DIN933GB5783-86ISO4017Hexagon head screws15开槽沉头螺钉DIN963GB68-85ISO2009Slottedｃｏｕｎｔersund head screws16开槽半沉头螺钉DIN964GB69-85ISO2010Slotted raisedｃｏｕｎｔersunk oval head screws17十字槽沉头螺钉DIN965GB819-85ISO7046Cross recessedｃｏｕｎｔersunk head screws18十字槽半沉头螺钉DIN966GB820-85ISO7047Cross recessed raised19十字槽盘头自攻螺攻DIN7981GB845-85ISO7049Pan head tapping screws with cross recessed20十字槽沉头自攻螺攻DIN7982GB846-85ISO7050ｃｏｕｎｔersunk flat head tapping screws with cross21十字槽半沉头自攻螺攻DIN7983GB847-86ISO7051Raisedｃｏｕｎｔersunk oval head tapping screws with cross22开槽盘头自攻螺钉DIN7971GB5282-85ISO1481Pan head tapping screws with slot23开槽沉头自攻螺钉DIN7972GB5283-85ISO1482ｃｏｕｎｔersunk flat head tapping screws with slot24开槽半沉头自攻螺钉DIN7973GB5284-85ISO1483Raised sountersunk oval head tapping screws with slot25六角头自攻螺钉DIN7976GB5285-85ISO1479Hexagon tapping screws26十字槽盘头螺钉DIN7985GB818-85ISO7045Pan head screws with cross recessed27内六角沉头螺钉DIN7991ISO10642Hexagon socket coutersunk head screws28六角头尼龙锁紧螺母DIN982GB812-88ISO2982Prevailing rorque type hexagon nuts,heavy type,with nylon29六角头薄型尼龙锁紧螺母DIN985GB889.1-86ISO7040Prevalling torque type hoxagon nuts,heavy type,with nylon30六角盖型尼龙锁紧螺母DIN986GB6172.2-86ISO10511Preailling torque typedomed capnuts with nylonｉｎｓｅｒｔ中德螺丝标准对应表31六角头螺母（1型）DIN934GB6170-86ISO4032Hexagon full nuts 32细牙六角头螺母（1型）DIN934GB6171-86ISO8673Hexagon full nuts 33六角头薄螺母DIN936GB6172.1-86ISO4035Hexagon thin nuts 34六角薄螺母DIN439GB6172-86ISO4035Hexagon thin nuts35开槽半沉头木螺钉DIN95GB101Slotted raised csk head wood screws36开槽半圆头木螺钉DIN96GB99Slotted round head wood screws37开槽沉头木螺钉DIN97GB100Slottedｃｏｕｎｔersunk head wood screws38鞍形弹垫DIN128-A GB7245-87Single coil spring lock washers 39弹簧止动垫圈DIN137-A Curved spring washers40波形弹垫DIN137-B GB955Wave spring washers41T型方颈螺栓DIN186GB37-88T-head blots with square neck 42T型双接头螺栓DIN188T-head bolts with double nip43螺纹圆锥销DIN258ISO8737Taper pins with threaded end44T型头螺栓DIN261T-head bolts45蝶型螺母（美制）DIN315AF Wing nuts America form46蝶型螺母（德制）DIN315DF GB62-88Wing nuts germany form47蝶型螺母（美制）DIN316AF Wing screws America form48蝶型螺母（德制）DIN317DF Wing screws germany form49圆球型盖型螺母DIN319Ball knobs50开槽带孔球面圆柱头蚴钉DIN404GB832-88Slotted capstan screws51开槽长圆柱端紧定螺钉DIN417GB75-85ISO7435Slotted set srews with full dog point52开槽平端紧定螺钉（半牙）DIN427GB73-85ISO2342Slotted set srews with chamfered end53小六角特薄细牙螺母DIN431GB808-88Pip nuts with thread54外舌止动垫圈DIN432GB856-88External tap55小垫圈(用于圆柱头螺钉)DIN433GB848-95ISO7092Washers for cheese head screws 56方斜垫圈（U型）DIN434GB852-88Square taper washers for57方斜垫圈（I型）DIN435GB852-88Square taper washers for58方垫圈DIN436Square washers59开槽凹端紧定螺钉DIN438GB74-85ISO7436Slotted set with cup point60细牙六角薄螺母DIN439GB6173-86ISO8675Hexagon thin nuts61木螺钉专用垫圈DIN440ISO7094Rounds washers for wood constructions62密封帽DIN443Sealing caps,push-in type63活节螺栓B型DIN444GB798-88Eye bolts form B64内舌止动垫圈DIN462Internal tab washers65双耳止动垫圈DIN463GB855-88Washers with two taps66滚花高头螺钉DIN464GB834-88Knurled thumb screws with collar67开槽滚花高头螺钉DIN465Slotted knurled thumb screws with collar68滚花高螺母DIN466GB806-88Knurled thumb nuts with collar 69滚花薄螺母DIN467GB807-88Knurled thumb thin nuts70锁紧垫圈DIN470Sealing washers71轴用弹性垫圈DIN471GB893-86Retaining rings for shafts(external),circlips72孔用弹性垫圈DIN472GB893.86Retaining rings for bores(internal),circlips73方头带垫螺栓DIN478Square head bolts with collar74方头圆柱底端螺栓DIN479Square head bolts with half dog point75方头带垫关圆底端螺栓DIN480Square head bolts with collar,half dog point76T型槽螺母DIN508ISO299T-slot nuts77单头螺柱DIN525Single end studs 78地脚螺栓DIN529GB799-88Masonry bolts79带槽圆螺母DIN546GB817-76Slotted round nuts80端面带孔圆螺母DIN547GB815-88Round nuts with drilled holes in one face81开槽平端紧定螺钉DIN551GB73-85ISO4776Slotted set screws with flat point82开槽锥端紧定螺钉DIN553GB71-85ISO7434Slotted set screws with cone point83六角螺母DIN555ISO4034Hexagon nuts 84方螺母-C DIN557GB39-88Square nuts85六角头螺钉DIN558ISO4018Hexagon screws86六角头圆柱端紧定螺钉DIN561Hexagon set screws with full dog point87薄型方螺母-B DIN562Square nuts without bevel 88六角头木螺钉DIN571GB102-86Hexgon head wood screw89吊环螺钉DIN580GB825-76ISO3266Lifting eye bolts90吊环螺母DIN582Lifting eye nuts91六角头螺栓DIN601ISO4016Hexagon blots92大半圆头方颈螺栓（马车螺栓）DIN603GB14-88ISO8677Mushroom head square neckbolts(carriage bolts)93沉头带插销马车螺栓DIN604Flatｃｏｕｎｔersunk nib bolts94沉头长方颈马车螺栓DIN605Flatｃｏｕｎｔersunk long squareneck bolts95半圆头带插销马车螺栓DIN607Cup head nib bolts96沉头短方颈马车螺栓DIN608Flatｃｏｕｎｔersunk short square neck bolts97六角头精配螺栓（长螺纹）DIN609Hexagon fitted bolts,long thread 98六角头精配螺栓（短螺栓）DIN610Hexagon fitted bolts short thread 99滚花平头螺钉DIN653GB835-88Knurled thumb screws thin type 100半圆头铆钉DIN660GB867-86ISO1051Round head rivets101沉头铆钉DIN661GB869-86ISO1051Contersunk head rivets102半沉头铆钉DIN662ISO1051Raised contersunk head rivets103大扁头铆钉DIN674ISO1051Mushroom head rivets104重型侧面带孔圆螺母DIN703Adjusting rings,heavy range(shafting collars)105侧面带孔圆螺母DIN705GB816-88Adjusting rings,light range(shafting collars)106卡头DIN741Wire rope clips107T型槽螺钉DIN787ISO299T-slot screws108双头螺柱（牙长=2D）DIN835GB900-88Studs-metal(end=2d)109内六角锥型闭锁螺钉DIN906Hexagon socket pipe plugs,conical thread110内六角直型闭锁螺钉DIN908Thread 111外六角锥型闭锁螺钉DIN909Thread112外六角直型闭锁螺钉DIN910Hexagon head screw plugs,cyl.thread113薄型盲螺母DIN917Hexagon cap nuts114开槽小圆柱头螺钉DIN920Slotted short cheese head screws 115开槽大圆柱头螺钉DIN921GB838-88Slotted large cheese head screws116开槽圆柱头轴肩螺钉DIN923GB830-88Slotted pan head screw with shoulder117开槽无头轴肩螺钉DIN927Slotted shoulder screws118焊接方螺母DIN928GB/T13680-92Square weld nuts119焊接六角螺母DIN929GB/T13681-92Hexagon weld nuts120六角头螺母DIN970Hexagon nuts type-1121六角头螺母DIN971Hexagon nuts type-2122细牙六角头螺母（2型）DIN972Hexagon nuts with fine thread123开槽六角螺母DIN935GB6178-86ISO7035Hexagon slotted andｃａｓｔle nuts124六角头开槽薄螺母DIN937GB6181-86ISO7038Hexagon thin slotted and caslte nuts125双头螺距（牙长=1D）DIN938GB897-88Studs metal(end=1d) 126双头螺距（牙长=1.5D DIN939GB898-88Studs metal(end=1.25d)127双头螺距（牙长=1.25D DIN940Studs metal(end=1.5d)128六角头细牙螺栓（全牙）DIN960GB5785-86ISO8765Hexagon head bolts,metric fine pitch thread129六角头细牙螺栓（半牙）DIN961GB8786-86ISO8676Hexagon head bolts,metric fine pitch thread130头部穿孔六角头螺栓DIN962Additional shapes and versions for bolts131牙条（全螺纹）DIN975GB6176-86ISO8674Threaded rods(studdings) 132螺纹销DIN976GB15389-94Threaded pins(stud bolts)133六角头开槽薄螺母2型DIN979Hexagon thin slotted andｃａｓｔle nuts134全金属六角锁紧螺母1型DIN980Prevaillng rorque type hexagon nuts,all metal nuts135圆螺母DIN981GB6184-86ISO7199Locknuts136配合垫片DIN988Shim rings137木材连接用垫片DIN1052Washers for timber connectors 138沉头钢钉DIN1151Round plain head nails139销钉专用垫片A型DIN1440ISO8738Plain washers for clevis pins(A) 140销钉专用垫片DIN1441Plain washers for clevis pins 141带头销钉DIN1444ISO2341Clevis pins with head142圆锥型槽销DIN1471GB/T13829.2ISO8744Grooved pins,taper grooved143圆锥型槽销（半槽）DIN1472GB/T13829.2ISO8745Grooved pins,taper grooved half length144平行槽销（带倒角）DIN1473ISO8740Grooved pins,parallel grooved full length145前端凹槽槽销DIN1474ISO8741Grooved pins,reverve grooved half length146中部凹槽槽销DIN1475ISO8742Grooved pins,center grooved 147圆头槽销DIN1476ISO8746Grooved pins with round head148沉头槽销DIN1477ISO8747Grooved pins withｃｏｕｎｔersunk head149六角螺母棒DIN1479Turnuckles(center parts),made out of hexagon bar150花蓝螺栓DIN1480Turnuckles with eye bolt and hook bolt151弹性圆柱销DIN1481GB879-86ISO8752Spring pins,heavy type 152组合式盖型螺母DIN1587GB802-88Hexagon domed cap nuts153开槽圆螺母(配合沟头扳手)DIN1804Slotted round nuts for hook spammer154圆螺母（带插销孔）DIN1816Round nuts with set holes155盘型弹簧垫圈DIN2093Disc springs156喉箍DIN3017Hose clamps157润滑油嘴（旋扭头）DIN3404Lubricating nipples,button head 158管夹DIN3567Shackles for conduilts159U型螺栓DIN3570Stirrup bolts(U-bolts)160球面垫圈DIN6319GB849-88Spherical washers,conical seats 161圆柱销DIN6325ISO8734Parallel pins162厚六角螺母DIN6330GB56-88Hexagon nuts,1.5d163厚六角法兰面螺母DIN6331GB6177-86Hexagon nuts,1.5d with collar 164长六角螺母DIN6334Hexagon nuts,3d165外齿锁紧垫圈DIN6797-A GB862.1-87External teeth lock washers166内齿锁紧垫圈DIN6797-I GB861.1-87Internal teeth lock washers167外锯齿锁紧垫圈DIN6798-A GB862.2-87External teeth serrated lock washers168内锯齿锁紧垫圈DIN6798-I GB861.2-87Internal teeth serrated lock washers169开口挡圈DIN6799GB896-76Retaining rings for shafts(E-rings),circlips170平键（A型）DIN6885ISO773/2491Parallel keys(form A)171半圆键DIN6888ISO3912Woodruff keys172嵌环（支撑环）DIN6899Thimbles173机器螺钉和垫圈组合件DIN6900Screws and washers assemblies174自攻螺钉和垫圈组合件DIN6901GB9074.1-17Tapping screws and washer assemblies175薄型带孔内六角圆柱螺钉DIN6912GB9074.18-23Hexagon cocket head cap screwswith hole,low head176大六角头螺栓DIN6914Hexagon head bolts with large head177大六角螺母DIN6915Hexagon nuts with large wideth across flat178大垫圈DIN6916Round washers for friction grip bolts179楔型方垫圈DIN6917Spuare taper washers for friction grip bolts on T-180六角法兰面螺母DIN6923GB6187-86ISO4161Hexagon flange nuts181全金属六角锁紧螺母2型DIN6925GB6185.1-2000ISO7042Prevailing torque type hexagonnuts,all metallic nuts182轻型弹性圆柱销DIN7346ISO13337Spring pins,light type183重型弹性圆柱销用垫圈DIN7349Washers for bolts with heavy type spring pinss184ISO公制螺纹螺钉多种头型DIN7500Thread forming screws for ISO-metric thread185开槽切削螺纹螺钉（多种头型）DIN7513Thread cutting screws186十字槽切削螺纹螺钉（多种头型）DIN7516Thread cutting screws crossrecess187T型四爪螺母DIN7965Tee nuts with pronge188钢结构用六角头螺栓连接副DIN7968GB1228/1229/1230Hexagon head fitted bolts forsteel structures189圆柱头螺钉用弹簧垫圈DIN7980ISO8738Spring lock washers for screws with cylindrical heads190薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reduced head191钢结构用垫圈DIN7989GB1230-84Washers for steel structures192钢结构用六角头螺栓DIN7990GB1229-84Hexagon head bolts for steel structures193轴用钢丝挡圈DIN7993GB895.2-86Roundwire snap rings for shafts194十字槽半沉头木螺钉DIN7995GB952-86Cross recessed raisedｃｏｕｎｔersunk head wood screws195十字槽圆头木螺钉DIN7996GB950-86Cross recessed round head wood screws196十字槽沉头木螺钉DIN7997GB951-86Cross recessedｃｏｕｎｔersunk head wood screws197螺纹护套(普通、自锁等)DIN8140Ciolｉｎｓｅｒｔs,coarse,fine thread,silf locking198大外径垫圈DIN9021GB96-85ISO7093Washers,outside diameter appro.3d 199弹簧卡子DIN11024sping cotter for a bolt200平板螺栓DIN13257Belting bolts(elevator bolts)201干壁钉（墙板钉）DIN18182Dry wall screws202环型螺母DIN28129GB63-88Lifting nuts(eye nuts)203圆螺母用止退DIN70952Tab washer for slotted round nuts 204圆锥销DIN1GB117ISO2339Taper pins205圆柱销DIN7GB119-86ISO2339Parallel pins206开槽圆柱头螺钉DIN84GB65-85ISO1207Slotted cheese head screws207开槽盘头螺钉DIN85GB67-85ISO1580Slotted pan head screws208单耳止动垫圈DIN93GB854Tab washers209开口销DIN94GB91ISO1234ｓｐｌｉｔcooter pins。

德国标准和国际标准、中国标准中英文对照表2008-11-22 12:01序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-StandardGB-Standard1 DIN1 圆锥销 taper pins ISO2339 GB1172 DIN7 圆柱销 parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉 slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉 slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈 tab washers GB8546 DIN94 开口销 split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉 slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉 slotted round head wood screws GB999 DIN97 开槽沉头木螺钉 slotted countersunk head wood screws GB10010 DIN125-A 平垫 plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫 plain washers ISO709113 DIN127-A 重型弹垫 spring lock washers,tang ends GB724414 DIN127-B 标准弹垫 spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫 single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈 curved spring washers17 DIN137-B 波形弹垫 wave spring washers GB95518 DIN186 T型方颈螺栓 T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓 T-head bolts with double nip20 DIN258 螺纹圆锥销 taper pins with threaded end ISO873721 DIN261 T型头螺栓 T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母 ball knobs27 DIN404 开槽带孔球面圆柱头螺钉 slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉 slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母 pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈 external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈 square washers36 DIN438 开槽凹端紧定螺钉 slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母 hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母 hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈 rounds washers for wood constructions ISO709440 DIN443 密封帽 sealing caps,push-in type41 DIN444 活节螺栓B 型 eye bolts form B GB798-8842 DIN462 内舌止动垫圈 internal tab washers43 DIN463 双耳止动垫圈 washers with two taps GB855-8844 DIN464 滚花高头螺钉 knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉 slotted knurled thumb screws with collar46 DIN466 滚花高螺母 knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母 knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈 sealing washers49 DIN471 轴用弹性挡圈 retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈 retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓 square head bolts with collar52 DIN479 方头圆柱底端螺栓 square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓 square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母 T-slot nuts ISO29955 DIN525 单头螺柱 single end studs56 DIN529 地脚螺栓 masonry bolts GB799-8857 DIN546 带槽圆螺母 slotted round nuts GB817-7658 DIN547 端面带孔圆螺母 round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉 slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉 slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母 hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉 hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉 hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉 hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉 lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母 lifting eye nuts69 DIN601 六角头螺栓 hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓 flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓 flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓 cup head nib bolts74 DIN608 沉头短方颈马车螺栓 flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹） hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹） hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉 knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉 round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉 contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉 raised contersunk head rivets ISO105181 DIN674 大扁头铆钉 mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母 adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母 adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头 wire rope clips85 DIN787 T型槽螺钉 T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D） studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉 hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉 hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉 hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉 hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手 socket wrenches ISO293692 DIN912 内六角圆柱头螺钉 hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉 hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉 hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉 hexagon socket set screws with dog point ISO4028GB79-8596 DIN916 内六角凹端紧定螺钉 hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母 hexagon cap nuts98 DIN920 开槽小圆柱头螺钉 slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉 slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉 slotted pan head screws with shoulder GB830-88 101 DIN927 开槽无头轴肩螺钉 slotted shoulder screws102 DIN928 焊接方螺母 square weld nuts GB/T13680-92103 DIN929 焊接六角螺母 hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙） hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙） hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母 hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母 hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母 hexagon thin slotted and castle nuts ISO7038 GB6181-86 111 DIN938 双头螺距（牙长=1D） studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D） studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D） studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙） hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙） hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓 additional shapes and versions for bolts117 DIN963 开槽沉头螺钉 slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉 slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉 cross recessed countersunk head screws ISO7046 GB819-85 120 DIN966 十字槽半沉头螺钉 cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母 hexagon nuts type-1122 DIN971 六角头螺母 hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销 threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型） hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型） prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母 locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母 prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母 prevailling torque type hexagon nuts,heavytype ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母 prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片 shim rings133 DIN1052 木材连接用垫片 washers for timber connectors134 DIN1151 沉头钢钉 round plain head nails135 DIN1440 销钉专用垫片A型 plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片 plain washers for clevis pins137 DIN1444 带头销钉 clevis pins with head ISO2341138 DIN1471 圆锥型槽销 grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740 141 DIN1474 前端凹槽槽销 grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销 grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销 grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销 grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒 turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓 turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销 spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母 hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手） slotted round nuts for hook spanner 150 DIN1816 圆螺母（带插销孔） round nuts with set holes151 DIN2093 盘型弹簧垫圈 disc springs152 DIN3017 喉箍 hose clamps153 DIN3404 润滑油嘴（旋扭头） lubricating nipples,button head154 DIN3567 管夹 shackles for conduilts155 DIN3570 U型螺栓 stirrup bolts(U-bolts)156 DIN6319 球面垫圈 spherical washers,conical seats GB849-88157 DIN6325 圆柱销 parallel pins ISO8734158 DIN6330 厚六角螺母 hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母 hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母 hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈 external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈 internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈 external teeth serrated lock washers GB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈 internal teeth serrated lock washers GB861.2-87 165 DIN6799 开口挡圈 retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型） parallel keys(form A ) ISO773/2491167 DIN6888 半圆键 woodruff keys ISO3912168 DIN6899 嵌环（支撑环） thimbles169 DIN6900 机器螺钉和垫圈组合件 screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件 tapping screws and washersassemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉 hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓 hexagon head bolts with large head(friction grip bolts) 173 DIN6915 大六角螺母 hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈 round washers for friction grip bolts175 DIN6917 楔型方垫圈 spuare taper washers for friction grip bolts on T-sections 176 DIN6923 六角法兰面螺母 hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型） prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头） blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉 rivets for brake and clutchlining GB875/975-86180 DIN7343 螺旋夹紧销 spiral pins ISO8750181 DIN7346 轻型弹性圆柱销 spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈 washers for bolts with heavy type spring pinss 183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread 184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess 187 DIN7965 T型四爪螺母 tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副 hexagon head fitted bolts for steelstructures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉 pan head tapping screws with slot ISO1481 GB5282-85 190 DIN7972 开槽沉头自攻螺钉 countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉 raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉 hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈 spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉 pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉 countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉 raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉 hexagon socket head cap screws with，reducedhead198 DIN7985 十字槽盘头螺钉 pan head screws with cross recessed ISO7045 GB818-85 199 DIN7989 钢结构用垫圈 washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓 hexagon head bolts for steel structures GB1229-84 201 DIN7991 内六角沉头螺钉 hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈 roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉 cross recessed raised countersunk head woodscrews GB952-86204 DIN7996 十字槽圆头木螺钉 cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉 cross recessed countersunk head wood screws GB951-86 206 DIN8140 螺纹护套（普通\自锁等） ciol inserts,coarse,fine thread,silf locking 207 DIN9021 大外径垫圈 washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子 spring cotter for a bolt209 DIN13257 平板螺栓 belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉） dry wall screws211 DIN28129 环型螺母 lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈 tab washers for slotted round nuts GB858-88。

德国标准DIN和国际标准、中国国家标准GB中英文对照表德国标准DIN和国际标准、中国国家标准GB中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈sealing washers GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nutsISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nyloninsert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert 132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structuresGB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical headsISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head 198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screwsGB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86 206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

_*常用螺栓的标准及规格表国家标准规定了螺纹规格为M3~M64,A和B级的六角头螺栓.A级用于D<=24和L<=10D或L<=150mm(按较小值)的螺栓;B级用于D>24或L>10D或L>150(按较小值)的螺栓外六角螺栓尺寸规格(如图)钢结构连接用螺栓性能等级分、、、、、、、、等10余个等级，其中级及以上螺栓材质为低碳合金钢或中碳钢并经热处理〔淬火、回火〕，通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两局部数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级级高强度螺栓，其材料经过热处理后，能到达：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区_*别，其性能是相同的，设计上只选用性能等级即可。

常用螺丝规格表类规格牙距成品外径线径类规格牙数成品外径线径(每英别±别±最大最小寸)最大最小1/8405/32323/1624英1/420制5/1618粗3/816牙7/161455°1/212国9/1612标粗5/811牙4#40605#40 6#32°8#32 M10美10#24 M11制12#24 M12粗1/420 M14牙5/1618 M1660°3/816 M187/1614 M201/2139/16125/8114#485#446#40国8#36标10#32细M10美12#28牙M10制1/428粗60M125/1624牙°M1260°3/824 M147/1620 M161/220 M189/1618 M205/818类牙数成品外径线径规格或别最大最小±牙数国标76602°日32制32A28牙24铁18铁16钉146012 10°9日40制32 AB28牙24铁20铁18钉166016 14°12日制木螺丝260°_*类牙数成品外径线径规格或别最大最小±牙数2#323#28美4#24制5#20铁6#18板7#16A8#15牙9#1460°10#1212#1114#102#32美3#284#24制5#20铁6#20板7#19AB8#18牙10#1660°12#141/414墙板6#17钉细7#16牙8#1560°10#12墙板6#9钉粗7#9牙8#960°10#8德标(C/B)钉240°强度等级所谓级和级是指螺栓的抗剪切应力等级为和公称抗拉强度800N/MM2公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*〔Y/10〕=此螺栓的屈服强度〔因为按标识规定：屈服强度/抗拉强度=Y/10〕===============如级那么此螺栓的_*抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米〔m〕、厘米〔cm〕、毫米〔mm〕等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸〔inch〕，相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

常用螺栓的标准及规格表国家标准规定了螺纹规格为M3~M64,A和B级的六角头螺栓.A级用于D<=24和L<=10D或L<=150mm(按较小值)的螺栓;B级用于D>24或L>10D或L>150(按较小值)的螺栓外六角螺栓尺寸规格(如图)钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

常用螺丝规格表强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8 公称抗拉强度800N/MM2 公称屈服强度640N/MM2 一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

【技术工艺】加工用语-中英文对照锻造 forging铸造 casting浇铸 moulding毛坯件 rough下料 cutting material压弯 bending整形 shaping压球 pressing into ball压扁 pressing to be flat敦台加热 heating氧化处理 oxidation processes 氧化皮 oxide film电磁炉 induction cooker电炉 electric furnace钝化处理 passivation成型 moulding机加工 machining工序 process生产工序 process of produceing 不锈钢 stainless steel原材料 raw material车丝 lathe thread搓丝滚丝抛光处理 polishing process抛光 polishing人工抛光 manual polishing机械抛光 machine polishing电解 electroanalysis振动 shaking酸洗套丝钻孔 drilling扩孔 enlarge the hole冲压 press冲压设备 press equipment机床加工 machining数控加工 CNC螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料qww球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国标）ISO(国际标准)DIN （德制）JIS （日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓C级Hexagon head bolts-product grade C六角头螺栓C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉螺栓、螺钉BOLTS & SCREWS德制六角头螺栓HEXAGON HEAD BOLTS DIN931德制六角头螺栓HEXAGON HEAD BOLTS DIN601德制六角头螺钉HEXAGON HEAD SCREWS DIN933德制六角头螺钉HEXAGON HEAD SCREWS DIN558六角头螺栓HEXAGON HEAD BOLTS ISO4014六角头螺钉HEXAGON HEAD SCREWS ISO4017美制六角头螺栓HEX BOLTS IFI C-6(A-6)美制六角头螺钉HEX CAP SCREWS IFI C-10(A-10)吊装螺栓DRAW BOLTS德制圆头方颈螺栓MUSHROOM HEAD SQUARE NECK BOLTS DIN603英制圆头方颈螺栓ROUND HEAD SQUARE NECK BOLTS B.S.美制圆头方颈螺栓ROUND HEAD SQUARE NECK BOLTS IFI C-40德制内六角圆柱头螺钉HEXAGON SOCKET HEAD CAP SCREWS DIN912内六角沉头螺钉HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS DIN7991拇指螺钉THUMB SCREWS IFI J-26内六角平头紧定螺钉HEXAGON SOCKET SET SCREWS WITH FLAT POINT DIN913内六角锥端紧定螺钉HEXAGON SOCKET SET SCREWS WITH CONE POINT DIN914内六角圆柱端紧定螺钉HEXAGON SOCKET SET SCREWS WITH DOG POINT DIN915内六角凹端紧定螺钉HEXAGON SOCKET SET SCREWS WITH CUP POINT DIN 916英制六角螺闩BLACK MILD STEEL HEXAGON BOLTS WITH NUTS B.S.德制吊环螺钉LIFTING EYE BOLTS DIN580德制六角法兰面螺栓HEXAGON FLANGE BOLTS DIN6921美制六角法兰面螺钉HEX FLANGE BOLTS IFI 111 1986 C-28德制钢结构用带螺母的六角头螺栓HEXAGON BOLTS WITH HEXAGON NUTS FOR STEEL STRUCTURES DIN7990钢结构用高强度大六角头螺栓HEXAGON BOLTS WITH LARGE WIDTHS ACROSS FLATS FOR HIGH-TENSILE BOLTING IN STEEL STRUCTURES DIN6914钢结构用高强度大六角螺母HEXAGON NUTS WITH LARGE WIDTHS ACROSS FLATS FOR HIGH-TENSILE IN STEEL STRUCTURES DIN6915钢结构用高强度垫圈WASHERS FOR HIGH-TENSILE BOLTING IN STEEL STRUCTURES DIN6916美制六角结构螺栓HEAVY HEX STRUCTURAL BOLTS IFI E-34结构钢联结件用的高强度螺栓HIGH STRENGTH BOLTS FOR STRUCTURAL STEEL JOINTS ASTM A325 TYPE 1热处理的钢结构螺栓、最小抗拉强度150ksi HEAT-TREATED STEEL STRUCTURAL BOLTS 150ksi MIN. TENSILE STRENGTH A490 TYLPE 1钢结构用扭剪型高强度螺栓连接副SETS OF TORSHEAR TYPE HIGH STRENGTH BOLT HEXAGON NUT AND PLAIN WASHER FOR STEEL STRUCTURES JSS 1109-1981螺杆STUDS DIN B.S. ANSI弯曲螺栓BENT BOLTS IFI 136 1986 C-86-87花兰螺丝TURNBUCKLE WITH HOOK AND EYE DIN1480钢管扣件STEEL PIPESCAFFOLD ISO 4054 JIS A8951六角螺母HEXAGON NUTS德制六角螺母HEXAGON NUTS DIN934德制六角螺母HEXAGON NUTS DIN555英制光六角螺母BRIGHT MILD STEEL HEX NUTS B.S.1083英制六角螺母 HEXAGON NUTS B.S.1768英制六角螺母 HEXAGON NUTS B.S.1769六角螺母HEXAGON NUTS ISO4032六角螺母HEXAGON NUTS ISO4033六角螺母HEXAGON NUTS ISO4034六角螺母HEXAGON NUTS AS1112美制六角螺母和六角锁紧螺母HEAVY HEX NUTS AND HEAVY HEX JAM NUTS IFI D-5(D-6)美制重型六角螺母和重型六角锁紧螺母HEAVY HEX NUTS AND HEAVY HEX JAM NUTS IFI D-14(D-12)美制六角厚螺母HEX THICK NUTS IFI D-8英制六角螺母BLACK MILD STEEL HEX NUTS B.S.916日制六角螺母HEXAGON NUTS B1181-1961 JIS日制六角螺母B1181 JIS六角螺母HEXAGON NUTS UNI 5587德制六角薄螺母CHAMFERED HEXAGON THIN NUTS DIN439六角薄螺母HEXAGON THIN NUTS ISO4035德制六角薄螺母HEXAGON THIN NUTS DIN936方螺母SQUARE NUTS德制方形薄螺母SQUARE THIN NUTS DIN562美制方形机螺钉螺母SQUARE MACHINE SCREWS NUTS IFI D-26英制方螺母SQUARE NUTS B.S.美制方螺母SQUARE NUTS IFI D-3美制重型方螺母HEAVY SQUARE NUTS IFI D-12德制方螺母SQUARE NUTS DIN557英制方螺母SQUARE NUTS B.S.吊环螺母LIFTING EYE NUTS公制外型的吋制螺母METRIC DIMENSIONS NUTS WITH UNC OR BSW THREAD德制吊环螺母LIFTING EYE NUTS DIN582六角法兰面螺母HEXAGON NUTS WITH FLANGE德制六角法兰面螺母HEXAGON NUTS WITH FLANGE DIN6923美制六角法兰面螺母HEX FLANGE NUTS IFI D-21蝶形螺母WING NUTS DIN315德制非金属嵌件六角锁紧螺母PREVAILING TORQUE TYPE HEXAGON THIN NUTS WITH NONMETALLIC INSERT DIN985德制金属嵌件六角锁紧螺母ALL-METAL PREVAILING TORQUE TYPE HEXAGON NUTS DIN980 焊接六角螺母HEXAGON WELD NUTS DIN929六角开槽螺母HEXAGON SLOTTED NUTS六角开槽螺母 HEXAGON SLOTTED NUTS DIN935六角开槽薄螺母 HEXAGON THIN SLOTTED NUTS DIN937六角开槽薄螺母 HEXAGON THIN SLOTTED NUTS DIN979盖形螺母HEXAGON CAP NUTS盖形螺母HEXAGON CAP NUTS DIN917盖形螺母HEXAGON DOMED CAP NUTS DIN986盖形螺母HEXAGON DOMED CAP NUTS DIN1587弹簧垫圈SPRING WASHERS德制弹簧垫圈SPRING LOCK WASHERS DIN127英制弹簧垫圈SPRING LOCK WASHERS B.S.美制弹簧垫圈LOCK WASHERS IFI L-9(K-13)平垫圈PLAIN WASHERS德制垫圈WASHERS (Grade A) DIN125德制垫圈WASHERS (Grade C) DIN126美制平垫圈（窄型）PLAIN WASHERS (NARROW) IFI L-2(K-4)美制平垫圈（宽型）PLAIN WASHERS (WIDE) IFI L-2(K-4)美制淬火垫圈HARDENED STEEL WASHERS ASTM F436开口销SPLIT PINS德制开口销SPLIT PINS DIN94美制开口销COTTER PINS L-38开口销 SPLIT PINS ISO1234英制开口销 COTTER PINS B.S.抽芯铆钉BLIND RIVET抽芯铆钉BLIND RIVET封闭形抽芯铆钉SEALED TYPE ALUMINIUM BLIND RIVET机器螺钉MACHINE SCREWS英制镀锌瓦楞螺闩GALVANIZED ROOFING BOLTS & NUTS B.S.德制瓦楞螺闩ROOFING BOLTS & NUTS德制开槽圆柱头螺钉SLOTTED CHEESE HEAD SCREWS DIN84德制开槽盘头螺钉SLOTTED PAN HEAD SCREWS DIN85美制开槽盘头机螺钉SLOTTED PAN HEAD MACHINE SCREWS IFI I-22(F-24)德制十字槽球面圆柱头螺钉CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985美制十字槽盘头机螺钉CROSS RECESSED PAN HEAD MACHINE SCREWS IFI I-23(F-25)德制开槽沉头螺钉SLOTTED COUNTERSUNK HEAD SCREWS DIN963美制开槽沉头机螺钉SLOTTED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-6(F-8) 德制十字槽沉头螺钉CROSS RECESSED COUNTERSUNK FLAT HEAD SCREWS DIN965美制十字槽沉头机螺钉CROSS RECESSED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-7(F-9)德制开槽半沉头螺钉SLOTTED RAISED COUNTERSUNK HEAD SCREWS DIN964美制开槽半沉头机螺钉SLOTTED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFII-16(F-18)德制十字槽半沉头螺钉CROSS RECESSED RAISE COUNTERSUNK HEAD SCREWS DIN966美制十字槽半沉头机螺钉CROSS RECESSED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFI I-17（F-19）美制开槽扁圆头机螺钉SLOTTED TRUSS HEAD MACHINE SCREWS IFI I-26(F-28)美制十字槽扁圆头机螺钉CROSS RECESSED TRUSS HEAD MACHINE SCREWS IFI I-27(F-29) AT吊装螺栓ACOUSTICAL TOGGLES木螺钉WOOD SCREWS德制开槽半沉头木螺钉SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95美制开槽半沉头木螺钉OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-38(F-58)英制开槽半沉头木螺钉SLOTTED OVAL HEAD WOOD SCREWS B.S.1210德制十字槽半沉头木螺钉CROSS RECESSED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN7995美制十字槽半沉头木螺钉OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-39(F-59)英制十字槽半沉头木螺钉SLOTTED OVAL HEAD WOOD SCREWS B.S.1210德制开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS DIN96英制开槽圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS B.S.1210德制十字槽半圆头木螺钉CROSS RECESSED ROUND WOOD SCREWS DIN7996德制开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97美制开槽沉头木螺钉FLAT COUNTERSUNK HEAD WOOD SCREWS IFI J-36(F-56)英制开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS B.S.1210AE木螺钉ACOUSTICALL EYELAGS德制十字槽沉头木螺钉FLAT COUNTERSUNK HEAD WOOD SCREWS DIN7997美制十字槽沉头木螺钉CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS IFIJ-37(F-57)英制十字槽沉头木螺钉CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS B.S.1210 德制六角头木螺钉HEXAGON HEAD WOOD SCREWS DIN571美制六角头木螺钉HEX LAG SCREWS IFI C-18米字槽双线木螺钉POZIDRIVE TWINFAST WOOD SCREWS B.S.织维板螺钉CHIPBOARD SCREWS HARDENED织维板螺钉CHIPBOARD SCREWS HARDENED大螺距带筋织维板螺钉CHIPBOARD SCREWS WITH RIBS UNDER THE HEAD高低牙加硬螺钉 FERMACELL SCREWS WITH RIBS UNDER THE HEAD自攻螺钉TAPPING SCREWS德制开槽盘头自攻螺钉PAN HEAD TAPPING SCREWS WITH SLOT DIN7971美制开槽盘头自攻螺钉SLOTTED PAN HEAD TAPPING SCREWS IFI H-38(E-34)德制十字槽盘头自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWS DIN7981美制十字槽盘头自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWS IFI H-39(E-35) 德制开槽沉头自攻螺钉COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7972美制开槽沉头自攻螺钉SLOTTED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFIH-24(E-20)德制开槽半沉头自攻螺钉RAISED COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7973美制开槽半沉头自攻螺钉SLOTTED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFIH-32(E-28)德制十字槽半沉头自攻螺钉CROSS RECESSED RAISED COUNTERSUNK HEAD TAPPING SCREWS DIN7983美制十字槽半沉头自攻螺钉CROSS RECESSED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFI H-33(E-39)双线快牙干壁-S型十字槽喇叭头DRY WALL SCREWS TYPE S PHILLIPS RECESSED BUGLEHEAD TWINFAST粗牙干壁螺钉DRY WALL SCREWS德制十字槽沉头自攻螺钉CROSS RECESSED COUNTERSUNK HEAD TAPPING SCREWSDIN7982美制十字槽沉头自攻螺钉CROSS RECESSED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFI H-25(E-21)十字槽扁圆头带垫面自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWS WITH COLLAR DIN968六角头带垫面自攻螺钉HEXAGON WASHER HEAD TAPPING SCREWS DIN6928自钻自攻螺钉SELF-DRILLING TAPPING SCREWS DIN7504螺栓包装PACKING OF BOLTS六角头螺栓 HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓 HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓 HEXAGON HEAD BOLTS ISO4014圆头方颈螺栓 MUSHROOM HEAD SQUARE NECK BOLTS DIN603圆头方颈螺栓 ROUND HEAD SQUARE NECK BOLTS IFI C-40六角螺钉包装>PACKING OF HEXAGON HEAD SCREWS六角头螺钉HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉HEXAGON HEAD SCREWS ISO4017六角头螺钉HEX CAP SCREWS IFI C-10(A-10)内六角螺钉包装PACKING OF HEXAGON SOCKET HEAD CAP SCREWS DIN912内六角沉头螺钉包装PACKING OF HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS DIN7991螺母包装PACKING OF NUTS六角螺母HEXAGON NUTS DIN934，DIN555六角螺母HEXAGON NUTS AS1112，ISO4032六角薄螺母HEXAGON THIN NUTS DIN439六角薄螺母HEXAGON THIN NUTS DIN936尼龙锁紧螺母NYLON JAM NUTS DIN985六角开槽螺母HEX SLOTTED NUTS DIN935方形薄螺母SQUARE THIN NUTS DIN562方螺母SQUARE NUTS DIN557蝶形螺母WING NUTS DIN315六角螺母HEXAGON NUTS DIN5587吊环螺母LIFTING EYE NUTS DIN582六角法兰面螺母HEXAGON NUTS WITH FLANG DIN6923六角螺母HEXAGON NUTS BS1768厚六角螺母HEXAGON THICK NUTS BS1768六角螺母HEXAGON NUTS BS916六角螺母HEXAGON NUTS IFI D-5(D-6)六角锁紧螺母HEX JAM NUTS IFI D-5(D-6)重型六角螺母HEAVY HEX NUTS A325, IFI D-14螺母包装PACKING OF NUTS六角开槽螺母 HEX SLOTTED NUTS DIN937六角盖型螺母 HEXAGON DOMED CAP NUTS DIN1587焊接六角螺母 HEXAGON WEID NUTS DIN929垫圈包装PACKING OF WASHERS垫圈 WASHERS DIN125,DIN126弹簧垫圈 SPRING LOCK WASHERS DIN127弹簧垫圈 LOCK WASHERS IFI L-9(K-13)机螺钉包装PA CKING OF MACHINE SCREWS开槽圆柱头螺钉SLOTTED CHEESE HEAD SCREWS DIN84开槽沉头螺钉SLOTTED COUNTERSUNK HEAD SCREWS DIN963开槽盘头螺钉SLOTTED PAN HEAD SCREWS DIN85十字槽球面圆柱头螺钉CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985自攻螺钉包装PACKING OF TAPPING SCREWS开槽、十字槽沉头自攻螺钉COUNTERSUNK HEAD TAPPING SCREWS DIN7972, DIN7982 开槽、十字槽盘头自攻螺钉PAN HEAD TAPPING SCREWS DIN7971, DIN7981木螺钉包装PACKING OF WOOD SCREWS开槽半沉头木螺钉SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS DIN96开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS B.S.1210开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS B.S.1210六角头木螺钉HEXAGON HEAD WOOD SCREWS DIN571织维板螺钉包装PACKING OF CHIPBOARD SCREWS织维板螺钉CHIPBOARD SCREWS HARDENED双线快牙干壁螺钉DRY WALL SCREWS TWINFAST。

2000年4月7日第一版工厂现有DIN标准目录及与GB国标参考对照表本文件使用说明：1、本文件没有经过编制部门的同意，任何人不得私自更改和删除。

2、本文件中所列相关标准，在总师办均可查到完整的标准原件，欢迎查阅使用。

3、本文件中所列相关标准对照仅供参考。

由于许多DIN 标准无法与GB标准完全等同，所以具体使用中应参阅原标准文件对照选用。

序号D IN标准号中文名称参考GB国标号备注1 DIN 1圆锥销GB117-862 DIN 7 圆柱销GB119-863 DIN13T13 公制ISO螺纹GB196-814 DIN 93 单耳止动垫圈GB854-885 DIN 94开口销GB91-866 DIN 95开槽半沉头木螺钉GB101-867 DIN 101 铆钉技术条件GB116-868 DIN 124 半圆头铆钉GB863.1-869 DIN 125垫片(精制) GB97.1(2)-8510 DIN 126垫片(粗制) GB95-8511 DIN 127弹簧垫圈GB7244-8712 DIN 128 弹簧垫圈（鞍形及波形）GB7246-87 、GB7245-8713 DIN 137 弹簧垫圈（鞍形及波形）GB860-87 、GB955-8714 DIN 258 螺伪锥销GB881-8615 DIN 267 金属连接元件16 DIN 268 切向键及键槽GB1974-8017 DIN 271 切向键及键槽GB1974-8018 DIN 302 沉头铆钉GB866-8619 DIN 315 碟形螺母GB94.1-8720 DIN 431 管螺母GB62-8821 DIN 432外舌止动垫圈GB856-8822 DIN 433垫圈(针对螺栓)23 DIN 434垫圈(矩形,用于U形梁)24 DIN 435垫圈(矩形,用于I形梁)25 DIN 436垫圈(矩形,用于木形梁)26 DIN 439轻型六角螺母GB6174-8627 DIN 440垫圈(用于木结构) GB5287-85(圆孔)28 DIN 442密封盖(压制型)29 DIN 463双耳止动垫圈GB855-8830 DIN 466滚花螺母（高式）GB806-8831 DIN 467滚花螺母（低式）GB807-8832 DIN 471弹性挡圈(轴用) GB894.1(2)-8633 DIN 472弹性挡圈(孔用) GB893.1-8634 DIN 522 金属结构垫圈GB8286-8535 DIN 526 保险帽（与DIN84配用）36 DIN 546 带槽螺母G817-88B37 DIN 547 端面带孔圆螺母GB815-8838 DIN 548 侧面带孔圆螺母GB816-8839 DIN 555螺母(M5～M100×6 C级) GB41-8640 DIN 557 方螺母（C级）41 DIN 562 方螺母（B级薄形）42 DIN 571六角头木螺钉GB102-8643 DIN 582环形螺母GB63-8844 DIN 603大半圆头方颈螺栓GB14-8845 DIN 604沉头带榫螺钉GB11-8846 DIN 625滚动轴承(单列带凹槽) GB176-8247 DIN 660 半圆头铆钉GB867-8648 DIN 661 沉头螺钉49 DIN 662 埋头螺钉50 DIN 674 大扁圆头螺栓GB1011-8651 DIN 675 半埋头螺钉52 DIN 798 锚固用螺母53 DIN 910螺塞54 DIN 912内六角圆头螺钉GB70-8554.1 DIN 913 内六角平端紧定螺钉GB77-8555 DIN 917 六角带帽螺母56 DIN 918 金属连接元件（与ISOB比较）57 DIN 928 方形焊接螺母58 DIN 929 六角焊接螺母GB/T13681-199259 DIN 931 六角螺栓(带柱) GB5782-8660 DIN 933六角螺栓(全螺纹) GB5783-8661 DIN 934六角螺母(A、B级) GB6170-8662 DIN 935T1 六角带槽螺母(A、B级) GB 6178-8663 DIN 935T2 六角带槽螺母(C级) GB 6179-8664 DIN 936 六角薄螺母(A、B级) GB 6172-8665 DIN 937开槽薄螺母GB6181-8666 DIN 938 双头螺柱bm≈1d GB897-8867 DIN 939双头螺柱bm≈1.25d GB898-8868 DIN 946 螺栓、螺母摩擦系数69 DIN 960螺栓GB5782-8670 DIN 963开槽沉头螺钉GB68-8571 DIN 964开槽半沉头螺钉GB69-8572 DIN 971T1 螺母（6、8级）GB6171-8673 DIN 971T2 螺母（10、12级）GB6176-8674 DIN 975螺纹杆75 DIN 979 开槽薄螺母GB6181-8676 DIN 980 螺母77 DIN 982螺母GB41-86、GB6170-8678 DIN 带齿弹性挡圈79 DIN 带齿弹性挡圈80 DIN 985螺母GB6172-8681 DIN 986六角带帽螺母82 DIN 988调整环支撑垫圈GB886-8583 DIN 1143 机械钉84 DIN 1144 平板头钉85 DIN 1151 圆直钉86 DIN 1152 圆直钉87 DIN 1157 装修用钉88 DIN 1158 钩头钉89 DIN 1160 平头钉90 DIN 1163 钉91 DIN 1433无头柱销GB880-8692 DIN 1434小头柱销GB882-8693 DIN 1435小头柱销94 DIN 1436大头柱销95 DIN 1440垫圈（销用中型）GB848-8596 DIN 1441垫圈（粗制）97 DIN 1445 销钉98 DIN 1469 带颈凹口销99 DIN 1471凹口锥销100 DIN 1473凹口柱销101 DIN 1475翼形凹口销102 DIN 1478拉线螺母103 DIN 1479 拉线螺母104 DIN 1480 拉线螺母105 DIN 1481弹性圆柱销（重型）GB879-86 106 DIN 1499张紧套107 DIN 1587 六角带帽螺母GB 802-88 108 DIN 2510 带接口螺母109 DIN 3404平头注油嘴110 DIN 5401球111 DIN 5417开口垫圈112 DIN 5525无头柱销（线路机械用）113 DIN 5526带头柱销（线路机械用）114 DIN 6303 滚花螺母115 DIN 6330 1.5d高六角螺母116 DIN 6331 1.5d高带缘螺母117 DIN 6340 压紧机构用螺母118 DIN 6796 夹紧垫圈119 DIN 6791 圆头带孔铆钉120 DIN 6792 沉头带孔铆钉GB874-86 121 DIN 6797 内、外齿锁紧垫圈GB862.2-87、GB861.1-87 、GB956.1-87 122 DIN 6798锯齿锁紧垫圈GB861.2-87、GB862.2-87 、GB956.2-87 123 DIN 6799保险垫片GB896-86 124 DIN 6880精制楔铁125 DIN 6881 孔用楔键126 DIN 6883 平面楔键127 DIN 6884 钩头楔键128 DIN 6885键及槽GB1095-79 129 DIN 6886键及槽GB1563-79 130 DIN 6887钩头楔键GB1565-79 131 DIN 6888半圆键GB1098-79GB1099-79 132 DIN 6889钩头楔键133 DIN 6902 垫圈134 DIN 6903 垫圈135 DIN 6904 波形弹性垫圈136 DIN 6905 鞍形弹性垫圈GB7245-87 137 DIN 6907 外锯齿锁紧垫圈GB862.2-87 138 DIN 6908 夹紧垫圈139 DIN 6912内六角圆柱头螺钉140 DIN 6913带支撑套的弹簧挡圈141 DIN 6914螺栓（长导杆）142 DIN 6915 螺母143 DIN 6916 垫片144 DIN 6917 方楔形垫片145 DIN 6918 方楔形垫片146 DIN 6923 带法兰螺母147 DIN 6924 锁紧螺母148 DIN 6925 锁紧螺母149 DIN 6926 带法兰锁紧螺母150 DIN 6927 带法兰锁紧螺母GB6187-86 151 DIN 7331 空心销152 DIN 7337 抽心铆钉153 DIN 7338 铆钉GB875-86、GB876-86、GB975-86、GB872-86 154 DIN 7339 空心铆钉GB876-86 155 DIN 7340 管状铆钉GB975-86 156 DIN 7341 无头铆钉GB1016-86 157 DIN 7346弹性圆柱销（轻型）158 DIN 7349垫圈159 DIN 7603密封圈160 DIN 7604螺堵161 DIN 7623空心六角螺栓162 DIN 7793 轴、孔用钢丝挡圈GB895.1-86、GB895.2-86 163 DIN 7933加固支座164 DIN 7965旋入螺母165 DIN 7967保险螺母166 DIN 7980弹簧垫圈GB93-87 167 DIN 7984内六角圆柱头螺钉GB70-85168 DIN 7991内六角沉头螺钉169 DIN 8187滚子链170 DIN 9021垫片GB96-85 171 DIN 9045 张力垫圈172 DIN 00124 插簧173 DIN 22425 三边形螺母174 DIN 71412锥形注油嘴175 DIN 71752 叉头176 DIN 71802角接头组件177 DIN 80705薄螺母178179180181182183184185186187188189190191192193194195196197。

螺栓性能等级的含义螺栓性能等级的含义钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8 公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

螺栓性能等级的含义钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8 公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

1、公制计量：（10进制）1m =100 cm=1000 mm2、英制计量：（8进制）1英寸=8英分 1英寸=25.4 mm 3/8¢¢×25.4 =9.523、1/4¢¢以下的产品用番号来表示其称呼径，如：4#， 5#， 6#， 7#， 8#， 10#， 12#螺纹一、螺纹是一种在固体外表面或内表面的截面上，有均匀螺旋线凸起的形状。

钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa8.8公称抗拉强度800N/MM2 公称屈服强度640N/MM2一般的螺栓是用"X.Y"表示强度的，X*100=此螺栓的抗拉强度，X*100*（Y/10）=此螺栓的屈服强度（因为按标识规定：屈服强度/抗拉强度=Y/10）===============如4.8级则此螺栓的抗拉强度为：400MPa屈服强度为：400*8/10=320MPa=================另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释度量当今世界上长度计量单位主要有两种，一种为公制，计量单位为米（m）、厘米（cm）、毫米（mm）等，在欧州、我国及日本等东南亚地区使用较多，另一种为英制，计量单位主要为英寸（inch），相当于我国旧制的市寸，在美国、英国等欧美国家使用较多。

1、公制计量：（10进制）1m =100 cm=1000 mm2、英制计量：（8进制）1英寸=8英分 1英寸=25.4 mm 3/8￠￠×25.4 =9.523、1/4￠￠以下的产品用番号来表示其称呼径，如：4#， 5#， 6#， 7#， 8#， 10#， 12#螺纹一、螺纹是一种在固体外表面或内表面的截面上，有均匀螺旋线凸起的形状。

【技术工艺】加工用语-中英文对照锻造 forging铸造 casting浇铸 moulding毛坯件 rough下料 cutting material压弯 bending整形 shaping压球 pressing into ball压扁 pressing to be flat敦台加热 heating氧化处理 oxidation processes氧化皮 oxide film电磁炉 induction cooker电炉 electric furnace钝化处理 passivation成型 moulding机加工 machining工序 process生产工序 process of produceing不锈钢 stainless steel原材料 raw material车丝 lathe thread搓丝滚丝抛光处理 polishing process抛光 polishing人工抛光 manual polishing机械抛光 machine polishing电解 electroanalysis振动 shaking酸洗套丝钻孔 drilling扩孔 enlarge the hole冲压 press冲压设备 press equipment机床加工 machining数控加工 CNC螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料qww球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国标）ISO(国际标准)DIN （德制）JIS （日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓 C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓 C级Hexagon head bolts-product grade C六角头螺栓 C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹 C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员 B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉螺栓、螺钉 BOLTS & SCREWS德制六角头螺栓 HEXAGON HEAD BOLTS DIN931德制六角头螺栓 HEXAGON HEAD BOLTS DIN601德制六角头螺钉 HEXAGON HEAD SCREWS DIN933德制六角头螺钉 HEXAGON HEAD SCREWS DIN558六角头螺栓 HEXAGON HEAD BOLTS ISO4014六角头螺钉 HEXAGON HEAD SCREWS ISO4017美制六角头螺栓 HEX BOLTS IFI C-6(A-6)美制六角头螺钉 HEX CAP SCREWS IFI C-10(A-10)吊装螺栓 DRAW BOLTS德制圆头方颈螺栓 MUSHROOM HEAD SQUARE NECK BOLTS DIN603英制圆头方颈螺栓 ROUND HEAD SQUARE NECK BOLTS B.S.美制圆头方颈螺栓 ROUND HEAD SQUARE NECK BOLTS IFI C-40德制内六角圆柱头螺钉 HEXAGON SOCKET HEAD CAP SCREWS DIN912内六角沉头螺钉 HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS DIN7991拇指螺钉 THUMB SCREWS IFI J-26内六角平头紧定螺钉 HEXAGON SOCKET SET SCREWS WITH FLAT POINT DIN913内六角锥端紧定螺钉 HEXAGON SOCKET SET SCREWS WITH CONE POINT DIN914内六角圆柱端紧定螺钉 HEXAGON SOCKET SET SCREWS WITH DOG POINT DIN915内六角凹端紧定螺钉 HEXAGON SOCKET SET SCREWS WITH CUP POINT DIN 916英制六角螺闩 BLACK MILD STEEL HEXAGON BOLTS WITH NUTS B.S.德制吊环螺钉 LIFTING EYE BOLTS DIN580德制六角法兰面螺栓 HEXAGON FLANGE BOLTS DIN6921美制六角法兰面螺钉 HEX FLANGE BOLTS IFI 111 1986 C-28德制钢结构用带螺母的六角头螺栓 HEXAGON BOLTS WITH HEXAGON NUTS FOR STEEL STRUCTURES DIN7990 钢结构用高强度大六角头螺栓 HEXAGON BOLTS WITH LARGE WIDTHS ACROSS FLATS FOR HIGH-TENSILE BOLTING IN STEEL STRUCTURES DIN6914钢结构用高强度大六角螺母 HEXAGON NUTS WITH LARGE WIDTHS ACROSS FLATS FOR HIGH-TENSILE IN STEEL STRUCTURES DIN6915钢结构用高强度垫圈 WASHERS FOR HIGH-TENSILE BOLTING IN STEEL STRUCTURES DIN6916美制六角结构螺栓 HEAVY HEX STRUCTURAL BOLTS IFI E-34结构钢联结件用的高强度螺栓 HIGH STRENGTH BOLTS FOR STRUCTURAL STEEL JOINTS ASTM A325 TYPE 1热处理的钢结构螺栓、最小抗拉强度150ksi HEAT-TREATED STEEL STRUCTURAL BOLTS 150ksi MIN. TENSILE STRENGTH A490 TYLPE 1钢结构用扭剪型高强度螺栓连接副 SETS OF TORSHEAR TYPE HIGH STRENGTH BOLT HEXAGON NUT AND PLAIN WASHER FOR STEEL STRUCTURES JSS 1109-1981螺杆 STUDS DIN B.S. ANSI弯曲螺栓 BENT BOLTS IFI 136 1986 C-86-87花兰螺丝 TURNBUCKLE WITH HOOK AND EYE DIN1480钢管扣件 STEEL PIPESCAFFOLD ISO 4054 JIS A8951六角螺母 HEXAGON NUTS德制六角螺母 HEXAGON NUTS DIN934德制六角螺母 HEXAGON NUTS DIN555六角螺母 HEXAGON NUTS ISO4032六角螺母 HEXAGON NUTS ISO4033六角螺母 HEXAGON NUTS ISO4034六角螺母 HEXAGON NUTS AS1112美制六角螺母和六角锁紧螺母 HEAVY HEX NUTS AND HEAVY HEX JAM NUTS IFI D-5(D-6)美制重型六角螺母和重型六角锁紧螺母 HEAVY HEX NUTS AND HEAVY HEX JAM NUTS IFI D-14(D-12) 美制六角厚螺母 HEX THICK NUTS IFI D-8日制六角螺母 HEXAGON NUTS B1181-1961 JIS日制六角螺母 B1181 JIS六角螺母 HEXAGON NUTS UNI 5587德制六角薄螺母 CHAMFERED HEXAGON THIN NUTS DIN439六角薄螺母 HEXAGON THIN NUTS ISO4035德制六角薄螺母 HEXAGON THIN NUTS DIN936方螺母 SQUARE NUTS德制方形薄螺母 SQUARE THIN NUTS DIN562美制方形机螺钉螺母 SQUARE MACHINE SCREWS NUTS IFI D-26英制方螺母 SQUARE NUTS B.S.美制方螺母 SQUARE NUTS IFI D-3美制重型方螺母 HEAVY SQUARE NUTS IFI D-12德制方螺母 SQUARE NUTS DIN557英制方螺母 SQUARE NUTS B.S.吊环螺母 LIFTING EYE NUTS公制外型的寸制螺母 METRIC DIMENSIONS NUTS WITH UNC OR BSW THREAD德制吊环螺母 LIFTING EYE NUTS DIN582六角法兰面螺母 HEXAGON NUTS WITH FLANGE德制六角法兰面螺母 HEXAGON NUTS WITH FLANGE DIN6923美制六角法兰面螺母 HEX FLANGE NUTS IFI D-21蝶形螺母 WING NUTS DIN315德制非金属嵌件六角锁紧螺母 PREVAILING TORQUE TYPE HEXAGON THIN NUTS WITH NONMETALLIC INSERT DIN985德制金属嵌件六角锁紧螺母 ALL-METAL PREVAILING TORQUE TYPE HEXAGON NUTS DIN980焊接六角螺母 HEXAGON WELD NUTS DIN929六角开槽螺母 HEXAGON SLOTTED NUTS六角开槽螺母 HEXAGON SLOTTED NUTS DIN935六角开槽薄螺母 HEXAGON THIN SLOTTED NUTS DIN937六角开槽薄螺母 HEXAGON THIN SLOTTED NUTS DIN979盖形螺母 HEXAGON CAP NUTS盖形螺母 HEXAGON CAP NUTS DIN917盖形螺母 HEXAGON DOMED CAP NUTS DIN986盖形螺母 HEXAGON DOMED CAP NUTS DIN1587弹簧垫圈 SPRING WASHERS德制弹簧垫圈 SPRING LOCK WASHERS DIN127英制弹簧垫圈 SPRING LOCK WASHERS B.S.美制弹簧垫圈 LOCK WASHERS IFI L-9(K-13)平垫圈 PLAIN WASHERS德制垫圈 WASHERS (Grade A) DIN125德制垫圈 WASHERS (Grade C) DIN126美制平垫圈（窄型） PLAIN WASHERS (NARROW) IFI L-2(K-4)美制平垫圈（宽型） PLAIN WASHERS (WIDE) IFI L-2(K-4)美制淬火垫圈 HARDENED STEEL WASHERS ASTM F436开口销 SPLIT PINS德制开口销 SPLIT PINS DIN94美制开口销 COTTER PINS L-38开口销 SPLIT PINS ISO1234英制开口销 COTTER PINS B.S.抽芯铆钉 BLIND RIVET抽芯铆钉 BLIND RIVET封闭形抽芯铆钉 SEALED TYPE ALUMINIUM BLIND RIVET机器螺钉 MACHINE SCREWS英制镀锌瓦楞螺闩 GALVANIZED ROOFING BOLTS & NUTS B.S.德制瓦楞螺闩 ROOFING BOLTS & NUTS德制开槽圆柱头螺钉 SLOTTED CHEESE HEAD SCREWS DIN84德制开槽盘头螺钉 SLOTTED PAN HEAD SCREWS DIN85美制开槽盘头机螺钉 SLOTTED PAN HEAD MACHINE SCREWS IFI I-22(F-24)德制十字槽球面圆柱头螺钉 CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985美制十字槽盘头机螺钉 CROSS RECESSED PAN HEAD MACHINE SCREWS IFI I-23(F-25)德制开槽沉头螺钉 SLOTTED COUNTERSUNK HEAD SCREWS DIN963美制开槽沉头机螺钉 SLOTTED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-6(F-8)德制十字槽沉头螺钉 CROSS RECESSED COUNTERSUNK FLAT HEAD SCREWS DIN965美制十字槽沉头机螺钉 CROSS RECESSED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-7(F-9)德制开槽半沉头螺钉 SLOTTED RAISED COUNTERSUNK HEAD SCREWS DIN964美制开槽半沉头机螺钉 SLOTTED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFI I-16(F-18)德制十字槽半沉头螺钉 CROSS RECESSED RAISE COUNTERSUNK HEAD SCREWS DIN966美制十字槽半沉头机螺钉 CROSS RECESSED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFI I-17（F-19）美制开槽扁圆头机螺钉 SLOTTED TRUSS HEAD MACHINE SCREWS IFI I-26(F-28)美制十字槽扁圆头机螺钉 CROSS RECESSED TRUSS HEAD MACHINE SCREWS IFI I-27(F-29)AT吊装螺栓 ACOUSTICAL TOGGLES木螺钉 WOOD SCREWS德制开槽半沉头木螺钉 SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95美制开槽半沉头木螺钉 OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-38(F-58)德制十字槽半沉头木螺钉 CROSS RECESSED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN7995美制十字槽半沉头木螺钉 OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-39(F-59)德制开槽半圆头木螺钉 SLOTTED ROUND HEAD WOOD SCREWS DIN96德制十字槽半圆头木螺钉 CROSS RECESSED ROUND WOOD SCREWS DIN7996德制开槽沉头木螺钉 SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97美制开槽沉头木螺钉 FLAT COUNTERSUNK HEAD WOOD SCREWS IFI J-36(F-56)AE木螺钉 ACOUSTICALL EYELAGS德制十字槽沉头木螺钉 FLAT COUNTERSUNK HEAD WOOD SCREWS DIN7997美制十字槽沉头木螺钉 CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS IFI J-37(F-57)德制六角头木螺钉 HEXAGON HEAD WOOD SCREWS DIN571美制六角头木螺钉 HEX LAG SCREWS IFI C-18米字槽双线木螺钉 POZIDRIVE TWINFAST WOOD SCREWS B.S.织维板螺钉 CHIPBOARD SCREWS HARDENED织维板螺钉 CHIPBOARD SCREWS HARDENED大螺距带筋织维板螺钉 CHIPBOARD SCREWS WITH RIBS UNDER THE HEAD高低牙加硬螺钉 FERMACELL SCREWS WITH RIBS UNDER THE HEAD自攻螺钉 TAPPING SCREWS德制开槽盘头自攻螺钉 PAN HEAD TAPPING SCREWS WITH SLOT DIN7971美制开槽盘头自攻螺钉 SLOTTED PAN HEAD TAPPING SCREWS IFI H-38(E-34)德制十字槽盘头自攻螺钉 CROSS RECESSED PAN HEAD TAPPING SCREWS DIN7981美制十字槽盘头自攻螺钉 CROSS RECESSED PAN HEAD TAPPING SCREWS IFI H-39(E-35)德制开槽沉头自攻螺钉 COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7972美制开槽沉头自攻螺钉 SLOTTED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFI H-24(E-20)德制开槽半沉头自攻螺钉 RAISED COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7973美制开槽半沉头自攻螺钉 SLOTTED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFI H-32(E-28)德制十字槽半沉头自攻螺钉 CROSS RECESSED RAISED COUNTERSUNK HEAD TAPPING SCREWS DIN7983 美制十字槽半沉头自攻螺钉CROSS RECESSED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFI H-33(E-39)双线快牙干壁-S型十字槽喇叭头 DRY WALL SCREWS TYPE S PHILLIPS RECESSED BUGLE HEAD TWINFAST 粗牙干壁螺钉 DRY WALL SCREWS德制十字槽沉头自攻螺钉 CROSS RECESSED COUNTERSUNK HEAD TAPPING SCREWS DIN7982美制十字槽沉头自攻螺钉 CROSS RECESSED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFI H-25(E-21) 十字槽扁圆头带垫面自攻螺钉 CROSS RECESSED PAN HEAD TAPPING SCREWS WITH COLLAR DIN968六角头带垫面自攻螺钉 HEXAGON WASHER HEAD TAPPING SCREWS DIN6928自钻自攻螺钉 SELF-DRILLING TAPPING SCREWS DIN7504螺栓包装 PACKING OF BOLTS六角头螺栓 HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓 HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓 HEXAGON HEAD BOLTS ISO4014圆头方颈螺栓 MUSHROOM HEAD SQUARE NECK BOLTS DIN603圆头方颈螺栓 ROUND HEAD SQUARE NECK BOLTS IFI C-40六角螺钉包装 >PACKING OF HEXAGON HEAD SCREWS六角头螺钉 HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉 HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉 HEXAGON HEAD SCREWS ISO4017六角头螺钉 HEX CAP SCREWS IFI C-10(A-10)内六角螺钉包装 PACKING OF HEXAGON SOCKET HEAD CAP SCREWS DIN912内六角沉头螺钉包装 PACKING OF HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS DIN7991螺母包装 PACKING OF NUTS六角螺母 HEXAGON NUTS DIN934，DIN555六角螺母 HEXAGON NUTS AS1112，ISO4032六角薄螺母 HEXAGON THIN NUTS DIN439六角薄螺母 HEXAGON THIN NUTS DIN936尼龙锁紧螺母 NYLON JAM NUTS DIN985六角开槽螺母 HEX SLOTTED NUTS DIN935方形薄螺母 SQUARE THIN NUTS DIN562方螺母 SQUARE NUTS DIN557蝶形螺母 WING NUTS DIN315六角螺母 HEXAGON NUTS DIN5587吊环螺母 LIFTING EYE NUTS DIN582六角法兰面螺母 HEXAGON NUTS WITH FLANG DIN6923六角螺母 HEXAGON NUTS BS1768厚六角螺母 HEXAGON THICK NUTS BS1768六角螺母 HEXAGON NUTS BS916六角螺母 HEXAGON NUTS IFI D-5(D-6)六角锁紧螺母 HEX JAM NUTS IFI D-5(D-6)重型六角螺母 HEAVY HEX NUTS A325, IFI D-14螺母包装 PACKING OF NUTS六角开槽螺母 HEX SLOTTED NUTS DIN937六角盖型螺母 HEXAGON DOMED CAP NUTS DIN1587焊接六角螺母 HEXAGON WEID NUTS DIN929垫圈包装 PACKING OF WASHERS垫圈 WASHERS DIN125,DIN126弹簧垫圈 SPRING LOCK WASHERS DIN127弹簧垫圈 LOCK WASHERS IFI L-9(K-13)机螺钉包装 PA CKING OF MACHINE SCREWS开槽圆柱头螺钉 SLOTTED CHEESE HEAD SCREWS DIN84开槽沉头螺钉 SLOTTED COUNTERSUNK HEAD SCREWS DIN963开槽盘头螺钉 SLOTTED PAN HEAD SCREWS DIN85十字槽球面圆柱头螺钉 CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985自攻螺钉包装 PACKING OF TAPPING SCREWS开槽、十字槽沉头自攻螺钉 COUNTERSUNK HEAD TAPPING SCREWS DIN7972, DIN7982 开槽、十字槽盘头自攻螺钉 PAN HEAD TAPPING SCREWS DIN7971, DIN7981木螺钉包装 PACKING OF WOOD SCREWS开槽半沉头木螺钉 SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95开槽半圆头木螺钉 SLOTTED ROUND HEAD WOOD SCREWS DIN96开槽沉头木螺钉 SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97六角头木螺钉 HEXAGON HEAD WOOD SCREWS DIN571织维板螺钉包装 PACKING OF CHIPBOARD SCREWS织维板螺钉 CHIPBOARD SCREWS HARDENED双线快牙干壁螺钉 DRY WALL SCREWS TWINFAST。