TRF006—2010—电气强度测试报告
- 格式：doc
- 大小：51.50 KB
- 文档页数：1
□Pass (合格)
□Fail (不合格)
Coakdownoccurred on the insulation of itemduringthe test)
□测试期间,测试部件之间产生电弧(Flashoveroccurred on test partsduringthe test)
Others (其他测试电压):□
Overcurrent relay(过流继电器):□99mA□5mA
Insulation of parts(部件的绝缘):
□Betweenliveparts of different polarity(不同极性带电部件之间)
□Betweenlivepartsand the mounting surface(带电部件与安装表面之间)
□Between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts(压线处电缆的外表面与可触及金属部件之间)
Result(结论)：
Appliance (产品名称):
Photos of sample (样品照片):
Rating (额定参数):
Supplier.(供应商):
ERP No. or new sample
(物料编码或新测试样品):
Quantity of test samples
(测试的样品数量):
Date (日期):
Test mothod (测试标准):Clause10.2.2of IEC 60598-1:2008
□Betweenlivepartsand metal parts of the luminaire(带电部件与灯具可触及金属部件之间)
□Betweenlivepartsand metal parts of the luminaire(带电部件与灯具可触及金属部件之间)
□Between live parts which can become of different polarity through action of a switch(通过开关动作能成为不同极性的带电部件之间)
Test purpose (测试目的):To checkthe itemwhether compliance withthe standard(检查灯具是否符合标准).
Construction(结构):□Class I□Class II□Class III
Test voltage(测试电压):□500V□2U+1000V□4U+2000V□1500V□3000V□3750V
□测试期间没有产生任何击穿和电弧(No flashover or breakdown occurred during the test)
Remarkand photos(备注以及照片):
□Fail (不合格)
Coakdownoccurred on the insulation of itemduringthe test)
□测试期间,测试部件之间产生电弧(Flashoveroccurred on test partsduringthe test)
Others (其他测试电压):□
Overcurrent relay(过流继电器):□99mA□5mA
Insulation of parts(部件的绝缘):
□Betweenliveparts of different polarity(不同极性带电部件之间)
□Betweenlivepartsand the mounting surface(带电部件与安装表面之间)
□Between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts(压线处电缆的外表面与可触及金属部件之间)
Result(结论)：
Appliance (产品名称):
Photos of sample (样品照片):
Rating (额定参数):
Supplier.(供应商):
ERP No. or new sample
(物料编码或新测试样品):
Quantity of test samples
(测试的样品数量):
Date (日期):
Test mothod (测试标准):Clause10.2.2of IEC 60598-1:2008
□Betweenlivepartsand metal parts of the luminaire(带电部件与灯具可触及金属部件之间)
□Betweenlivepartsand metal parts of the luminaire(带电部件与灯具可触及金属部件之间)
□Between live parts which can become of different polarity through action of a switch(通过开关动作能成为不同极性的带电部件之间)
Test purpose (测试目的):To checkthe itemwhether compliance withthe standard(检查灯具是否符合标准).
Construction(结构):□Class I□Class II□Class III
Test voltage(测试电压):□500V□2U+1000V□4U+2000V□1500V□3000V□3750V
□测试期间没有产生任何击穿和电弧(No flashover or breakdown occurred during the test)
Remarkand photos(备注以及照片):
