外文原文
Study on Human Resource Allocation in Multi-Project Based on the Priority and the Cost of Projects
Lin Jingjing , Zhou Guohua
SchoolofEconomics and management, Southwest Jiao tong University ,610031 ,China
Abstract----This paper put forward the affecting factors of project’s priority. which is introduced into a multi-objective optimization model for human resource allocation in multi-project environment . The objectives of the model were the minimum cost loss due to the delay of the time limit of the projects and the minimum delay of the project with the highest priority .Then a Genetic Algorithm to solve the model was introduced. Finally, a numerical example was used to testify the feasibility of the model and the algorithm.
Index Terms—Genetic Algorithm, Human Resource Allocation, Multi-project’s project’s priority .
1.INTRODUCTION
More and more enterprises are facing the challenge of multi-project management, which has been the focus among researches on project management. In multi-project environment ,the share are competition of resources such as
capital , time and human resources often occur .Therefore , it’s critical to schedule projects in order to satisfy the different resource demands and to shorten the projects’duration time with resources constrained ,as in [1].For many enterprises ,the human resources are the most precious asset .So enterprises should reasonably and effectively allocate each resource , especially the human resource ,in order to shorten the time and cost of projects and to increase the benefits .Some literatures have discussed the resource allocation problem in multi-project environment with resources constrained. Reference [1] designed an iterative algorithm and proposed a mathematical model of the resource-constrained multi-project scheduling .Based on work breakdown structure (WBS) and Dantzig-Wolfe decomposition method ,a feasible multi-project planning method was illustrated , as in [2] . References [3,4] discussed the resource-constrained project scheduling based on Branch Delimitation method .Reference [5] put forward the framework of human resource allocation in multi-project in Long-term ,medium-term and short-term as well as research and development(R&D) environment .Based on GPSS language, simulation model of resources allocation was built to get
the project’s duration time and resources distribution, as in [6]. Reference [7] solved the engineering project’s resources optimization problem using Genetic Algorithms.
These literatures reasonably optimized resources allocation in multi-project, but all had the same prerequisite that the project’s importance is the same to each other .This paper will analyze the effects of project’s priority on human resource allocation ,which is to be introduced into a mathematical model ;finally ,a Genetic Algorithm is used to solve the model.
2.EFFECTS OF PROJECTS PRIORITY ON HUMAN RESOUCE ALLOCATION AND
THE AFFECTING FACTORS OF PROJECT’S PRIORITY
Resource sharing is one of the main characteristics of multi-project management .The allocation of shared resources relates to the efficiency and rationality of the use of resources .When resource conflict occurs ,the resource demand of the project with highest priority should be satisfied first. Only after that, can the projects with lower priority be considered.
Based on the idea of project classification management ,this paper classifies the affecting factors of project’s priority into three categories ,as the project’
s benefits ,the complexity of project management and technology , and the strategic influence on the enterprise’s future development . The priority weight of the project is the function of the above three categories, as shown in
(1). W=f(I,c,s…) (1)
Where w refers to project’s priority weight; I refers to the benefits of the project; c refers to the complexity of the project, including the technology and management;
s refers to the influence of the project on enterprise .The bigger the values of the three categories, the higher the priority is.
3.HUMAN RESOURCE ALLOCATION MODEL IN MULTI-PROJECT
ENVIRONMENT
3.1Problem Description
According to the constraint theory, the enterprise should strictly differentiate the bottleneck resources and the non-bottleneck resources to solve the constraint problem of bottleneck resources .This paper will stress on the limited critical human resources being allocated to multi-project with definite duration times and priority.
To simplify the problem, we suppose that that three exist
文献信息： 文献标题：The Existing Approaches to Sexuality Education Targeting Children: A Review Article（针对儿童的性教育的现有方法：综述文章）国外作者：Ganji J, Emamian M H, Maasoumi R, et al 文献出处：《Iranian Journal of Public Health》,2017 , 46 (7) :890-898 字数统计：英文2177单词，12737字符；中文3949汉字 外文文献： The Existing Approaches to Sexuality Education Targeting Children: A Review Article Abstract Background:We aimed to assess what is already known about sexuality education (SE)-related policy or practical issues using review methods to search and critically appraise the existing SE approaches targeting children under age 12 yr. Methods: We completed the data collection by an extensive search of the English and Persian published and unpublished literature, evidence from experts in the topic, and by searching citations. The MeSH-terms were sexuality and training, sexuality education and programs or approaches, sexuality and children, sexuality education and parents, sex or sexuality education, sex education and parents or caregivers. A systematic search of medical and health-related databases, the Cochrane Library and Web of Science was undertaken for the years 1970–2015 together with citation searching, reference list checking and recommendations from stakeholders to identify evidence for SE. Results: According to the inclusion criteria, 20 documents were identified. They were synthesized into three main categories as sexuality-related knowledge, attitudes, and parents' skills to manage children's sexual behavior and related education. Employed approaches to children's sexuality were reported to be effective in
forced concrete structure reinforced with an overviewRein Since the reform and opening up, with the national economy's rapid and sustained development of a reinforced concrete structure built, reinforced with the development of technology has been great. Therefore, to promote the use of advanced technology reinforced connecting to improve project quality and speed up the pace of construction, improve labor productivity, reduce costs, and is of great significance. Reinforced steel bars connecting technologies can be divided into two broad categories linking welding machinery and steel. There are six types of welding steel welding methods, and some apply to the prefabricated plant, and some apply to the construction site, some of both apply. There are three types of machinery commonly used reinforcement linking method primarily applicable to the construction site. Ways has its own characteristics and different application, and in the continuous development and improvement. In actual production, should be based on specific conditions of work, working environment and technical requirements, the choice of suitable methods to achieve the best overall efficiency. 1、steel mechanical link 1.1 radial squeeze link Will be a steel sleeve in two sets to the highly-reinforced Department with superhigh pressure hydraulic equipment (squeeze tongs) along steel sleeve radial squeeze steel casing, in squeezing out tongs squeeze pressure role of a steel sleeve plasticity deformation closely integrated with reinforced through reinforced steel sleeve and Wang Liang's Position will be two solid steel bars linked Characteristic: Connect intensity to be high, performance reliable, can bear high stress draw and pigeonhole the load and tired load repeatedly.
外文文献翻译 2.5.1译文：看电影的艺术 1930年代中期，沃尔特·迪斯尼才明确以动画电影娱乐观众的思想，动画片本身才成为放映主角（不再是其他剧情片的搭配）。于1937年下半年首映的动画片《白雪公主与七个小矮人》为动画片树立了极高的标准，至今任然指导着动画艺术家们。1940年，这一年作为迪斯尼制片厂的分水岭，诞生了《木偶奇遇记》和《幻想曲>。这些今天成为经典的作品在接下来的二十年中被追随效仿，产生了一系列广受欢迎的动画娱乐作品。包括《小飞象》，《灰姑娘》，《爱丽丝漫游仙境》，《彼得·潘》，《小姐与流浪儿》，他们的故事通常源自广为人知的文学故事。这些影片最不好的地方在于它们似乎越来越面向小观众。 在1966年第四你去死后，他的制片厂继续制作手绘动画影片，但是创作能量衰减，公司转而专注于著作真人是拍电影。然而1989年，对于我们所有孩子来说，动画《小美人鱼》赋予了迪士尼新的生命活力（就像animation这个词本身的定义一样——使有生命活力），从该片开始，出现了一系列令人惊叹不已的音乐动画片。两年后，《美女与野兽》问世，塔尔在制作过程中利用了计算机作为传统手绘技术的辅助手段，这部影片获得了奥斯卡最佳电影奖提名，它是第一部获此殊荣的动画片。更好的还在后面，就想着两部影片一样，后面紧接着出现的众多优秀作品——包括《狮子王》，《阿拉丁》，《花木兰》——延续了迪士尼的经典传统：大胆醒目的视觉效果、精致的剧本，以及我们在所有伟大的电影中，不管是动画还是其他类型中都能找到的普适性主题和出乎意料之处。迪士尼的新版《幻想曲》，又被称为《幻想曲2000》，把原版中的部分片段与新的创作部分糅合在一起。（而且，按照迪士尼管理层的说法，该片是首部在IMAX巨幕影院首映的剧情长片。） 亨利·塞利克执导了蒂姆·波顿出品的两部影片，即《圣诞惊魂夜》和《飞天巨桃历险记》——前者是一部完全原创的定格动画，影片画面有时渗透着无限的恐惧，后者改编自罗纳德·达尔的畅销儿童书，该影片以真人实景拍摄开始。《飞天巨桃历险记》对暴力画面和重大恐惧（比如说，离弃）的表达和处理毫无掩饰，表达的真实感受对成人来说和对儿童一样生动鲜明，而蒂姆·波顿的影片《僵尸新娘》，仅仅从名字上就已经显示出影片内容和该幽默表达的“成人”特
Inventory management Inventory Control On the so-called "inventory control", many people will interpret it as a "storage management", which is actually a big distortion. The traditional narrow view, mainly for warehouse inventory control of materials for inventory, data processing, storage, distribution, etc., through the implementation of anti-corrosion, temperature and humidity control means, to make the custody of the physical inventory to maintain optimum purposes. This is just a form of inventory control, or can be defined as the physical inventory control. How, then, from a broad perspective to understand inventory control? Inventory control should be related to the company's financial and operational objectives, in particular operating cash flow by optimizing the entire demand and supply chain management processes (DSCM), a reasonable set of ERP control strategy, and supported by appropriate information processing tools, tools to achieved in ensuring the timely delivery of the premise, as far as possible to reduce inventory levels, reducing inventory and obsolescence, the risk of devaluation. In this sense, the physical inventory control to achieve financial goals is just a means to control the entire inventory or just a necessary part; from the perspective of organizational functions, physical inventory control, warehouse management is mainly the responsibility of The broad inventory control is the demand and supply chain management, and the whole company's responsibility. Why until now many people's understanding of inventory control, limited physical inventory control? The following two reasons can not be ignored: First, our enterprises do not attach importance to inventory control. Especially those who benefit relatively good business, as long as there is money on the few people to consider the problem of inventory turnover. Inventory control is simply interpreted as warehouse management, unless the time to spend money, it may have been to see the inventory problem, and see the results are often very simple procurement to buy more, or did not do warehouse departments . Second, ERP misleading. Invoicing software is simple audacity to call it ERP, companies on their so-called ERP can reduce the number of inventory, inventory control, seems to rely on their small software can get. Even as SAP, BAAN ERP world, the field of
土木工程毕业设计外文文献翻译修订版 IBMT standardization office【IBMT5AB-IBMT08-IBMT2C-ZZT18】
外文文献翻译 Reinforced Concrete （来自《土木工程英语》） Concrete and reinforced concrete are used as building materials in every country. In many, including the United States and Canada, reinforced concrete is a dominant structural material in engineered construction. The universal nature of reinforced concrete construction stems from the wide availability of reinforcing bars and the constituents of concrete, gravel, sand, and cement, the relatively simple skills required in concrete construction, and the economy of reinforced concrete compared to other forms of construction. Concrete and reinforced concrete are used in bridges, buildings of all sorts underground structures, water tanks, television towers, offshore oil exploration and production structures, dams, and even in ships. Reinforced concrete structures may be cast-in-place concrete, constructed in their final location, or they may be precast concrete produced in a factory and erected at the construction site. Concrete structures may be severe and functional in design, or the shape and layout and be whimsical and artistic. Few other building materials off the architect and engineer such versatility and scope. Concrete is strong in compression but weak in tension. As a result, cracks develop whenever loads, or restrained shrinkage of temperature changes, give rise to tensile stresses in excess of the tensile strength of the concrete. In
专业资料 学院： 专业：土木工程 姓名： 学号： 外文出处：Structural Systems to resist (用外文写) Lateral loads 附件：1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并
不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。 抗弯矩框架 抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。 我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。 支撑框架 支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。
Animation Animation is the rapid display of a sequence of images of 2-D or 3-D artwork or model positions to create an illusion of movement. The effect is an optical illusion of motion due to the phenomenon of persistence of vision, and can be created and demonstrated in several ways. The most common method of presenting animation is as a motion picture or video program, although there are other methods. Early examples An Egyptian burial chamber mural, approximately 4000 years old, showing wrestlers in action. Even though this may appear similar to a series of animation drawings, there was no way of viewing the images in motion. It does, however, indicate the artist's intention of depicting motion. Early examples of attempts to capture the phenomenon of motion drawing can be found in paleolithic cave paintings, where animals are depicted with multiple legs in superimposed positions, clearly attempting to convey the perception of motion. Five images sequence from a vase found in Iran A 5,000 year old earthen bowl found in Iran.It has five images of a goat painted along the sides. This has been claimed to be an example of early animation. However, since no equipment existed to show the images in motion, such a series of images cannot be called animation in a true sense of the word. A Chinese zoetrope-type device had been
本科毕业设计 外文文献及译文 文献、资料题目：Designing Against Fire Of Building 文献、资料来源：国道数据库 文献、资料发表（出版）日期：2008.3.25 院（部）：土木工程学院 专业：土木工程 班级：土木辅修091 姓名：武建伟 学号：2008121008 指导教师：周学军、李相云 翻译日期： 20012.6.1
外文文献: Designing Against Fire Of Buliding John Lynch ABSTRACT: This paper considers the design of buildings for fire safety. It is found that fire and the associ- ated effects on buildings is significantly different to other forms of loading such as gravity live loads, wind and earthquakes and their respective effects on the building structure. Fire events are derived from the human activities within buildings or from the malfunction of mechanical and electrical equipment provided within buildings to achieve a serviceable environment. It is therefore possible to directly influence the rate of fire starts within buildings by changing human behaviour, improved maintenance and improved design of mechanical and electrical systems. Furthermore, should a fire develops, it is possible to directly influence the resulting fire severity by the incorporation of fire safety systems such as sprinklers and to provide measures within the building to enable safer egress from the building. The ability to influence the rate of fire starts and the resulting fire severity is unique to the consideration of fire within buildings since other loads such as wind and earthquakes are directly a function of nature. The possible approaches for designing a building for fire safety are presented using an example of a multi-storey building constructed over a railway line. The design of both the transfer structure supporting the building over the railway and the levels above the transfer structure are considered in the context of current regulatory requirements. The principles and assumptions associ- ated with various approaches are discussed. 1 INTRODUCTION Other papers presented in this series consider the design of buildings for gravity loads, wind and earthquakes.The design of buildings against such load effects is to a large extent covered by engineering based standards referenced by the building regulations. This is not the case, to nearly the same extent, in the
Commercial Buildings Abstract: A guide and general reference on electrical design for commercial buildings is provided. It covers load characteristics; voltage considerations; power sources and distribution apparatus; controllers; services, vaults, and electrical equipment rooms; wiring systems; systems protection and coordination; lighting; electric space conditioning; transportation; communication systems planning; facility automation; expansion, modernization, and rehabilitation; special requirements by occupancy; and electrical energy management. Although directed to the power oriented engineer with limited commercial building experience, it can be an aid to all engineers responsible for the electrical design of commercial buildings. This recommended practice is not intended to be a complete handbook; however, it can direct the engineer to texts, periodicals, and references for commercial buildings and act as a guide through the myriad of codes, standards, and practices published by the IEEE, other professional associations, and governmental bodies. Keywords: Commercial buildings, electric power systems, load characteristics 1. Introduction 1.1 Scope This recommended practice will probably be of greatest value to the power oriented engineer with limited commercial building experience. It can also be an aid to all engineers responsible for the electrical design of commercial buildings. However, it is not intended as a replacement for the many excellent engineering texts and handbooks commonly in use, nor is it detailed enough to be a design manual. It should be considered a guide and general reference on electrical design for commercial buildings. 1.2 Commercial Buildings The term “commercial, residential, and institutional buildings”as used in this chapter, encompasses all buildings other than industrial buildings and private dwellings. It includes office and apartment buildings, hotels, schools, and churches, marine, air, railway, and bus terminals, department stores, retail shops, governmental buildings, hospitals, nursing homes, mental and correctional institutions, theaters, sports arenas, and other buildings serving the public directly. Buildings, or parts of buildings, within industrial complexes, which are used as offices or medical facilities or for similar nonindustrial purposes, fall within the scope of this recommended practice. Today’s commercial buildings, because of their increasing size and complexity, have become more and more dependent upon adequate and reliable electric systems. One can better understand the complex nature of modern commercial buildings by examining the systems, equipment, and facilities listed in 1.2.1. 1.2.2 Electrical Design Elements In spite of the wide variety of commercial, residential, and institutional buildings, some electrical design elements are common to all. These elements, listed below, will be discussed generally in this section and in detail in the remaining sections of this recommended practice. The principal design elements considered in the design of the power, lighting, and auxiliary systems include: 1) Magnitudes, quality, characteristics, demand, and coincidence or diversity of loads and load factors 2) Service, distribution, and utilization voltages and voltage regulation 3) Flexibility and provisions for expansion
（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：
英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the
外文原文 Study on Human Resource Allocation in Multi-Project Based on the Priority and the Cost of Projects Lin Jingjing , Zhou Guohua SchoolofEconomics and management, Southwest Jiao tong University ,610031 ,China Abstract----This paper put forward the affecting factors of project’s priority. which is introduced into a multi-objective optimization model for human resource allocation in multi-project environment . The objectives of the model were the minimum cost loss due to the delay of the time limit of the projects and the minimum delay of the project with the highest priority .Then a Genetic Algorithm to solve the model was introduced. Finally, a numerical example was used to testify the feasibility of the model and the algorithm. Index Terms—Genetic Algorithm, Human Resource Allocation, Multi-project’s project’s priority . 1.INTRODUCTION More and more enterprises are facing the challenge of multi-project management, which has been the focus among researches on project management. In multi-project environment ,the share are competition of resources such as capital , time and human resources often occur .Therefore , it’s critical to schedule projects in order to satisfy the different resource demands and to shorten the projects’duration time with resources constrained ,as in [1].For many enterprises ,the human resources are the most precious asset .So enterprises should reasonably and effectively allocate each resource , especially the human resource ,in order to shorten the time and cost of projects and to increase the benefits .Some literatures have