模具专业英汉词典
模具常用成形方式
accurate die casting 精密压铸
powder forming 粉末成形
calendaring molding 压延成形
powder metal forging 粉末锻造
cold chamber die casting 冷式压铸
precision forging 精密锻造
cold forging 冷锻
press forging 冲锻
compacting molding 粉末压出成形
rocking die forging 摇动锻造
compound molding 复合成形
rotary forging 回转锻造
compression molding 压缩成形
rotational molding 离心成形
dip mold 浸渍成形
rubber molding 橡胶成形
encapsulation molding 注入成形
sand mold casting 砂模铸造
extrusion molding 挤出成形
shell casting 壳模铸造
sinter forging 烧结锻造
forging roll 轧锻
six sides forging 六面锻造
gravity casting 重力铸造
slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形
squeeze casting 高压铸造
hot chamber die casting 热室压铸
swaging 挤锻
hot forging 热锻
transfer molding 转送成形
injection molding 射出成形
warm forging 温锻
investment casting 精密铸造
matched die method 对模成形法
laminating method 被覆淋膜成形
low pressure casting 低压铸造
lost wax casting 脱蜡铸造
matched mould thermal forming 对模热成形模
模具成形不良
aberration 色差
bite 咬入
blacking hole 涂料孔(铸疵) blacking scab 涂料疤
blister 起泡
blooming 起霜
low hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉
bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱
check 细裂痕
checking 龟裂
chipping 修整表面缺陷
clamp-off 铸件凹痕
collapse 塌陷
color mottle 色斑
corrosion 腐蚀
crack 裂痕
crazing 碎裂
crazing 龟裂
deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑
fissure 裂纹
flange wrinkle 凸缘起皱
flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕
haircrack 发裂
haze 雾度
incrustation 水锈
indentation 压痕
internal porosity 内部气孔
mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
orange peel 橘皮状表面缺陷overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀
plate mark 模板印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹
resin wear 树脂脱落
riding 凹陷
sagging 松垂
saponification 皂化
scar 疤痕
scrap 废料
scrap jam 废料阻塞
scratch 刮伤/划痕
scuffing 深冲表面划伤
seam 裂痕
shock line 模口挤痕
short shot 充填不足
shrinkage pool 凹孔
sink mark 凹痕
skin inclusion 表皮折叠
straightening 矫直
streak 条状痕
surface check 表面裂痕
surface roughening 橘皮状表皮皱折 surging 波动
sweat out 冒汗
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹
模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模模具成形不良aberration 色差bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack
裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹
Top Plate 上托板(顶板)
Top Block 上垫脚
Punch Set 上模座
Punch Pad 上垫板
Punch Holder 上夹板
Stripper Pad 脱料背板
Up Stripper 上脱料板
Male Die 公模(凸模)
Feature Die 公母模
Female Die 母模(凹模)
Upper Mold Plate 上模板
Lower Mold Plate 下模板
Die Pad 下垫板
Die Holder 下夹板
Die Set 下模座
Bottom Block 下垫脚
Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板
Inner Stripper 内脱料板
Lower Stripper 下脱料板
Inner Guiding Post 内导柱
Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销
Mould Coil Spring 模具弹簧Lifter Pin 顶料销
Isoheight Sleeve 等高套筒
Pin 销
Lifter Guide Pin 浮升导料销
Guide Pin 导正销
Wire Spring 圆线弹簧
Outer Guiding Post 外导柱
Stop Screw 止付螺丝
Located Pin 定位销
Outer Bush 外导套
Punch 冲头
Insert 入块(嵌入件)
Deburring Punch 压毛边冲子
Groove Punch 压线冲子
Stamped Punch 字模冲子
Round Punch 圆冲子
Special Shape Punch 异形冲子
Bending Block 折刀
Roller 滚轴
Baffle Plate 挡块
Located Block 定位块
Supporting Block for Location 定位支承块Air Cushion Plate 气垫板
Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子
Stiffening Rib Punch Stinger 加强筋冲子
Ribbon Punch 压筋冲子
Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板
Sliding Block 滑块
Sliding Dowel Block 滑块固定块Active Plate 活动板
Lower Sliding Plate 下滑块板Upper Holder Block 上压块
Upper Mid Plate 上中间板
Spring Box 弹簧箱
Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板
Guide Pad 导料块
模具技术用语
各种常用模具成形方式
Accurate Die Casting 精密压铸Powder Forming 粉末成形
Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造
Cold Forging 冷锻
Press Forging 冲锻
Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形
Dip Mold 浸渍成形
Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形
Shell Casting 壳模铸造
Foam Forming 发泡成形
Sinter Forging 烧结锻造
Forging Roll 轧锻
Six Sides Forging 六面锻造
Gravity Casting 重力铸造
Slush Molding 凝塑成形
Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造
Hot Chamber Die Casting 热室压铸
Swaging 挤锻
Hot Forging 热锻
Transfer Molding 转送成形
Injection Molding 射出成形
Warm Forging 温锻
Investment Casting 精密铸造
Matched Die Method 对模成形法
Laminating Method 被覆淋膜成形
Low Pressure Casting 低压铸造
Lost Wax Casting 脱蜡铸造
Matched Mould Thermal Forming 对模热成形模Close Mold 合模
Demould 脱模脱模剂
Mould Unloading 开模
Eject 顶出
Tool Change Retooling Die Changing 换模Mould Clamping 锁模
各式模具分类用语
Bismuth Mold 铋铸模
Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模
Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模
Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具
Chill Mold 冷硬用铸模
Loose Mold 活动式模具
Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具
Manifold Die 分歧管模具
Counter Punch 反凸模
Modular Mold 组合模具
Double Stack Mold 双层模具
Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模
Multi-Gate Mold 复式浇口模具
Expander Die 扩径模
Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模
Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具
Plaster Mold 石膏模
Blank Through Dies 漏件式落料模Porous Mold 通气性模具
Duplicated Cavity Plate 复板模
Positive Mold 全压式模具
Fantail Die 扇尾形模具
Pressure Die 压紧模
Fishtail Die 鱼尾形模具
Profile Die 轮廓模
Flash Mold 溢料式模具
Progressive Die 顺序模
Gypsum Mold 石膏铸模
Portable Mold 手提式模具
Hot-Runner Mold 热流道模具
Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模
Punching Die 落料模
Lancing Die 切口模切缝模
Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模
Runless Injection Mold 无流道冷料模具Sectional Die 对合模具
Segment Mold 组合模
Semi-Positive Mold 半全压式模具Shaper 定型模套
Single Cavity Mold 单腔模具
Solid Forging Die 整体锻模
Split Forging Die 拼合锻模
Split Mold 双并式模具
Sprueless Mold 无注道残料模具Squeezing Die 挤压模
Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模
Swing Die 振动模具
Three Plates Mold 三片式模具Trimming Die 切边模
Unit Mold 单元式模具
Universal Mold 通用模具
Unscrewing Mold 退扣式模具Yoke Type Die 轭型模
模具厂常用之标准零配件
Air Vent Valve 通气阀Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流档板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板
Bottom board 浇注底板Bolster 垫板
Bottom Plate 下固定板Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting lug 铸耳
Cavity 模穴(模仁)
Cavity Retainer Plate 模穴托板Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口
Die Approach 模头料道
Die Bed 型底
Die Block 块形模体
Die Body 铸模座
Die Bush 合模衬套
Die Button 冲模母模
Die Clamper 夹模器
Die Fastener 模具固定用零件
Die Holder 母模固定板
Die Lip 模唇
Die Plate 冲模板
Die Set 冲压模座
Direct Gate 直接浇口
Dog Chuck 爪牙夹头
Dowel 定位梢
Dowel Hole 导套孔
Dowel Pin 合模梢
Dozzle 辅助浇口
Dowel Pin 定位梢
Draft 拔模锥度
Draw Bead 张力调整杆
Drive Bearing 传动轴承
Ejection Pad 顶出衬垫
Ejector 脱模器
Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫
Ejector Pin 顶出梢
Ejector Plate 顶出板
Ejector Rod 顶出杆
Ejector Sleeve 顶出衬套
Ejector Valve 顶出阀
Eye Bolt 环首螺栓
Filling Core 填充型芯椿入蕊
Film Gate 薄膜形浇口
Finger Pin 指形梢
Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针
Flash Gate 毛边形浇口
Flask 上箱
Floating Punch 浮动冲头
Gate 浇口
Gate Land 浇口面
Gib 凹形拉紧楔
Goose Neck 鹅颈管
Guide Bushing 引导衬套
Guide Pin 导梢
Guide Post 引导柱
Guide Plate 导板
Guide Rail 导轨
Head Punch 顶头冲孔
Headless Punch 直柄冲头
Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头
Impact Damper 缓冲器
Injection Ram 压射柱塞
Inlay Bush 嵌入衬套
Inner Plunger 内柱塞
Inner Punch 内冲头
Insert 嵌件
Insert Pin 嵌件梢
King Pin 转向梢
King Pin Bush 主梢衬套
Knockout Bar 脱模杵
Land 合模平坦面
Land Area 合模面
Leader Bush 导梢衬套
Lifting Pin 起模顶针起模杆
Lining 内衬
Locating Center Punch 定位中心冲头
Locating Pilot Pin 定位导梢
Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置
Moving Bolster Plate 可动侧模板
One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器Ring Gate 环型浇口
Roller 滚筒
Runner 流道
Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton 骨架
Slag Riser 冒渣口
Slide(Slide Core)滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套
Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Limit Stop Collar 限位套
Stop Pin 止动梢
焊接词典(1) (2009-03-30 10:19:46) 转载 分类:焊接 标签: 文化 一般焊接名词术语 0.焊接学术组织 1.焊接工艺方法 2.工艺参数 3.坡口、焊缝 4.接头 5.电弧、熔池、熔渣 6.焊机 0.焊接学术组织 1001 中国机械工程学会焊接学会 The Welding Institution of The Chinese Mechanical EngineeringSociety 1002 国际焊接学会 International Institute of Welding (IIW) 1.焊接工艺方法 1101 焊接welding 1102 熔焊fusion welding 1103 压焊pressure welding 1104 钎焊brazing; soldering 1105 焊接过程welding process 1106 焊接技术welding technique 1107 焊接工艺welding technology; welding procedure 1108 焊接操作welding operation 1109 焊接顺序welding sequence 1110 熔敷顺序buildup sequence; deposition sequence 1111 焊接方向direction of welding 1112 焊接位置position of welding 1113 焊缝倾角weld slope; inclination of weld axis 1114 焊缝转角weld rotation; angle of rotation 1115 平焊位置flat position of welding 1116 横焊位置horizontal position of welding 1117 立焊位置vertical position of welding 1118 仰焊位置overhead position of welding 1119 平焊downhand welding; flat position welding 1120 横焊horizontal position welding 1121 立焊vertical position welding 1122 仰焊overhead position welding 1123 向下立焊vertical down welding; downward welding in the vertical position 1124 向上立焊vertical up welding;
牛津词典系列 牛津辞典是英国牛津大学出版社出版的多种英语词典的统称,是英国语言词典的代表。牛津词典详细追溯了每个英语词的历史演变(对其最早的出现年代有明确的标注),释义和引证繁富,因而是英语词汇的最高权威。 牛津老大 The Oxford English Dictionary,20 Volume Set《牛津英语大辞典》【查早到1150年(的古旧词)】类似《汉语大词典》 牛津老大:最高级的牛津词典,就是The Oxford English Dictionary(20 Volume Set)简称OED,这是牛津兄弟的老大,也是英语词典界的圣经。它一共有20卷,目前国内书商动辄索价¥20000RMB。这么贵的词典谁会买呢?问得好。其实,没有任何人能够读完这本词典,它的存在更具有象征意义,象征着人类对知识无限的追求。 然而人类的这点成就这一切,在电子时代失去了骇人的体量和质感。OED的光盘版,只需要两张CD-ROM。但凡买过这套电子版的人,无不怨声载道,因为它的接口设计实在太差了。查完一个词之后,居然没有一个后退键。只能用鼠标浏览,但又不支持鼠标右键的COPY和粘贴。总之,如果花钱买来的话,大概会非常痛苦。 顺便说一句,The Oxford English Dictionary(20 Volume Set)有个缩印版,The Compact Oxford English Dictionary,内容跟OED一样,价格只要¥3200,但字体非常恐怖,是把OED四页的内容印到一页上,如果你不想写一部失乐园续集的话,最好还是打消买它的念头。 牛津老二 The New Shorter Oxford English Dictionary,2 Vol.Set《牛津简编英语词典》【查早到17世纪(的古旧词)】类似《辞源》 牛津老二:The New Shorter Oxford English Dictionary (2 Vol. Set),可能是牛津也觉得自己浪费森林太不象话,于是出了一个简编版。不要以为看到Shorter,就真Shorter,其实,这是牛津家族中第二大的词典。两大本3888页的厚度,也够意思了。这本词典在国内由上海外语教育出版社引进第五版。网上可以找到供Mdict词典软件使用的牛津简编词典包。 牛津老三 The New Oxford Dictionary of English《新牛津英语大词典》【查现代的(百科新词)】类似《辞海》 该词典国内已经出版了,双解版名为《新牛津英汉双解大词典》(上海外语教育出版社),在网上也要卖¥315左右。如果OED和SOED侧重词源学,引经据典太多,太学术的话,那么ODE就是给人类预备的。不过这本词典的中文翻译挺讨厌,因为把每个例句都翻译了,包括:“Yes,I will.” 这样的。如果你想拥有一本英英的原版,先不要急着去亚马逊下单,下面有一个终极解决办法,金山词霸2009[牛津版]收录其双解版。 牛津老四 Concise Oxford Dictionary《牛津简明英语词典》【查现代的(英文新词)】类似《现代汉语词典》 该词典是大学级别词典(College Dictionary),中高级用用也足够了,简称COD。由外语教学与研究出版社引进。
a horizon a 层位 a lineation a 线理 a twin a 双晶 aa lava 块熔岩 aalenian stage 阿林阶abandon 废弃abandoned mine 废弃的矿山abandoned well 废孔abatis 通风隔墙 abdomen 腹部 abdominal appendage 腹肢abdominal cavity 腹腔abdominal fin 腹 abductor 外展肌 abductor muscle 外展肌abernathyite 水砷钾铀矿aberration 象差 abichite 光线矿abiogenesis 自然发生abiogeny 自然发生 abiotic factor 非生物因素 ablation 剥蚀 ablation breccia 剥蚀角砾岩 ablation moraine 消融碛 ablation skin 熔蚀皮 ablation till 消融碛 ablykite 阿布石 abnormal 异常的 abnormal interference color 异常干涉色 abnormal metamorphism 异常变质酌 abolition 废除 abrade 剥蚀 abrasion 海蚀 abrasion platform 磨蚀台地 abrasion surface 浪蚀面 abrasion terrace 磨蚀阶地 abrasionn test 磨耗试验 abrasive 磨料;海蚀的
abrazite 多水高岭土 absarokite 正边玄武岩 absite 钍钛铀矿 absolute age 绝对年龄 absolute black body 绝对黑体 absolute chronology 绝对年代学 absolute dating 绝对年代测定 absolute geopotential 绝对重力势absolute porosity 绝对孔隙率 absolute pressure 绝对压力 absolute structure 绝对构造 absorbed water 吸附水 absorbent 吸收剂 absorber 吸收器 absorbing well 吸水井 absorption 吸收 absorption axis 吸收轴 absorption border 融蚀缘 absorption curve 吸收曲线 absorption edge 吸收端 absorption factor 吸收率 absorption spectrum 吸收光谱 absorptive capacity 吸收率 absorptivity 吸收性 abukumalite 铋磷灰石 abundance 丰度 abundance of elements 元素丰度 abundance of isotopes 同位素丰度 abundance ratio of isotopes 同位素相对丰度 abysmal deposits 深海沉积物 abyss 深海
A Type Wooden Ladder A字木梯A-frame A型骨架 A-truss A型构架 Abandon 废弃 Abandoned well 废井Aberration of needle 磁针偏差Abnormal pressure 异常压力abnormally high pressure 异常高压Abort 中止 abrasion 磨损 Abrasion surface 浪蚀面abrasive cut-off machine 磨切机Abrasive Cutting Wheel 拮碟abrasive grinding machine 研磨机Abrasive Grinding Wheel 磨碟abrasive particle 磨料颗粒Absolute address 绝对地址Absolute altitude 绝对高度Absolute damping 绝对阻尼Absolute deviation 绝对偏差Absolute flying height 绝对航高Absolute gravity 绝对重力absolute permeability 绝对渗透率absolute porosity 绝对孔隙率absolute temperature 绝对温度absorbability 吸收性;吸附性absorption 吸收 abutment 桥墩 abutting end 邻接端acceleration 加速acceleration lane 加速车道 Acceleration of gravity 重力加速度 acceleration pedal 加速器踏板 accelerator 催凝剂;加速器;催化剂 acceptance criteria 接受准则 access 通路;通道 access door 检修门;通道门 access lane 进出路径 access panel 检修门 access point 入口处;出入通道处 access ramp 入口坡道;斜通道 access road 通路;通道 access shaft 竖井通道 access spiral loop 螺旋式回旋通道 access staircase 通道楼梯 access step 出入口踏步 access tunnel 隧道通道 accessible roof 可到达的屋顶 accessory 附件;配件 accident 事故;意外 accidental collapse 意外坍塌 accommodate 装设;容纳 accredited private laboratory 认可的私人 实验室 accumulator 储压器;蓄电池 accuracy limit 精度限制 acetylene cylinder 乙炔圆筒 Acetylene Hose 煤喉 Acetylene Regulator 煤表 acid plant 酸洗设备;酸洗机 acid pump 酸液泵 acid tank 酸液缸 acidic rock 酸性岩 acoustic couplant 声耦合剂 acoustic coupler 声音藕合器;音效藕合 器 acoustic lining 隔音板 acoustic screen 隔声屏 Acoustic wave 声波 acrylic paint 丙烯漆料(压克力的油漆) acrylic sheet 丙烯胶片(压克力的胶片) active corrosion 活性腐蚀 active earth pressure 主动土压力 active fault 活断层 active oxidation 活性氧化 actual plot ratio 实际地积比率 actuator 促动器;唧筒;激发器 adapt 改装 adaptor 适配器;承接器;转接器; addition 增设;加建 additional building works 增补建筑工程 additional horizontal force 额外横向力 additional plan 增补图则(附加的平面图) additional vent 加设通风口 additive 添加剂 Address 地址 adhesive 黏结剂;胶黏剂 adhesive force 附着力 Adhesive Glue 万能胶 Adhesive Reflective Warning Tape 反光 警告贴纸 adit 入口;通路;坑道口 adjacent construction 相邻建造物 adjacent level 相邻水平 adjacent site 相邻基地 adjacent street 相邻街道 adjoining area 毗邻地区 adjoining building 毗邻建筑物 adjoining land 毗邻土地 adjoining structure 毗邻构筑物 adjustable 可调校 Adjustable Wrench Spanner 昔士 adjuster 调节器 adjustment 调校;调整 Administrative Lawsuit 行政诉讼 Administrative Remedy 行政救济 admixture 掺合剂;外加剂 advance directional sign 前置指路标志; 方向预告标志 advance earthworks 前期土方工程 advance warning sign 前置警告标志 advance works 前期工程 aeration 曝气 aeration tank 曝气池 aerial 天线 Aerial mapping 航空测图 aerial photograph 航测照片 Aerial photography 航照定位 aerial rapid transit system 高架快速运输 系统 1 / 60
专业英语词典网址大全 (https://www.doczj.com/doc/47997363.html,) 综合类 1. https://www.doczj.com/doc/47997363.html,/ (词霸在线------含多部专业词典) 2. https://www.doczj.com/doc/47997363.html,/ 英-英 (可以下载声音文件!!!) 3. https://www.doczj.com/doc/47997363.html,/ 词汇搜索引擎 4. https://www.doczj.com/doc/47997363.html,/zzjdict/ 郑州大学在线英汉-汉英科技大词典 5. https://www.doczj.com/doc/47997363.html,/default.asp 英汉-汉英翻译语料库 6. https://www.doczj.com/doc/47997363.html,/ 英-英,含大量图片 7. https://www.doczj.com/doc/47997363.html,/reference/ 美国最大的免费在线参考网站。 下有Columbia Encyclopedia, Roget's Thesauri, American Heritage Dictionary, Columbia History of English and American Literature等众多参考词典。更新快,内容丰富。 8. https://www.doczj.com/doc/47997363.html,/ 最常用的提问网站,可以通过查询分类查找问题答案,也可上帖提问。 生命科学类 1. https://www.doczj.com/doc/47997363.html,/search/dict-search.html (life science dictionary) 2. https://www.doczj.com/doc/47997363.html,/glossary/glossary.html 包括Biochemistry, Botany, Cell Biology, Ecology, Geology, Life History, Phylogenetics, Zoology 3. https://www.doczj.com/doc/47997363.html,/dictionary.asp 4. https://www.doczj.com/doc/47997363.html,/facu ... /BioBookglossA.html On-Line Biology Book: GLOSSARY 5. 基因专业词汇(可以下载声音文件的!!!!!!!) https://www.doczj.com/doc/47997363.html,/Terms/Glossary/findterm.htm 6. 细胞与分子生物学词典(第三版) https://www.doczj.com/doc/47997363.html,/dictionary/
阀门材质材料英汉术语词典(2009/07/18 14:52) 目录:公司动态 浏览字体:大中小阀门材质材料英汉术语词典 阀门材质-钢铁材料 copper 合金 cast steel 铸钢 Steel Casting iron 碳素钢铸件 Fine Steel Casting iron 优质碳素钢 Stainless steel 不锈钢 Stainless acid-resisting steel 不锈耐酸钢 Chromium-molybdenum steel 铬钼钢 Chrominm-molybdenum-vanadium steel 铬钼钒钢 Spring steel 弹簧钢 Chromium stainless steel 铬不锈钢 Gray Cast iron 灰铸铁 nodular cast iron 球墨铸铁 Ductile Cast iron 球墨铸铁 Chromel alloy 镍铬合金 Hayne's alloy 钴铬钨合金 High tem perature steel 高温钢 Low tem perature steel 低温钢 Monel 蒙乃尔合金 bar 棒材 billet 方钢,钢方坯 bloom 钢坯,钢锭 section 型材 steel ingot 钢锭
阀门材质-有色金属材料 bronze 青铜 brass 黄铜 Pure cupper 纯铜 Cuprum alloy 铜合金 Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Pure aluminum 纯铝 阀门材质-塑料材料 Nylon 尼龙塑料Polytetrafluoroethylene 聚四氟乙烯 阀门材质-橡胶材料 CHR rubber 氯晴橡胶 Buna-N rubber 丁晴橡胶 Rubbeer graphite board 橡胶石墨板Fluorous rubber 氟橡胶 阀门材质-其他材料 Expanded graphite 柔性石墨Stainless and Graphite 不锈钢/石墨stock 原料 Ceramic metal 陶瓷金属 阀门产品种类术语-valve英汉互译词典阀门 valve 通用阀门 General valve 球阀 Ball valve 槽车球阀 Tank Lorry Ball Valves
陕西中北中等专业学院 焊接技术应用专业人才培养方案 一、专业名称 专业名称:焊接技术应用 专业代码:052200 二、入学要求(招生对象) 中等职业学校学历教育入学要求一般为初中毕业或具有同等学历者。 三、修业年限 中等职业学校学历教育修业3年。 四、职业面向 等全方面发展的,掌握焊接技术与工程专业必备的基科学技术极大地推动了社会经济的发展,尤其是我国制造业的发展.焊接技术是制造业中的一项重要工艺,同时还作为一项新型技术在各个领域内广泛应用,发挥着不容小觑的作用.焊接技术的优劣与产品的质量和性
能有着直接联系,焊接技术的发展程度已成为多个国家机械制造水平的重要评价标准之一。 五、培养目标与培养规格 (一)、培养的目标 本专业培养拥护党的基本路线,德、智、体、美础理论知识和专业知识,具备从事焊接专业领域实际工作的综合能力和主要技能,能够胜任焊条电弧焊、氩弧焊、CO2气体保护焊、气焊、气割、碳弧气刨、及各种自动化焊接方法的施焊操作;焊接结构生产工艺的实施,焊接设备维修及管理,焊接质量检验等工作的中级焊接技术应用型人才。 (二)、培养规格 本专业培养的毕业生应具有以下知识结构和能力要求(职业素质、专业知识、专业能力)。 1.职业素质 1).具有良好的职业道德,能自觉遵守行业法规、规范和企业规章制度。 2).具有创新精神和服务意识。 3).具有人际交往与团队协作能力。 4).具备获取信息、学习新知识的能力。 5).具有借助词典阅读外文技术资料的能力。 6).具有一定的计算机操作能力。
7).具有安全文明生产、节能环保和遵守操作规程的意识。 8).具有控制焊接质量意识。 2、专业知识 1)具有一定的社会科学和人文知识; 2)具有本专业必需的焊接技术基础理论知识; 3)具有供配电技术的基础知识; 4)具有焊接施工与维护的基本知识; 3、专业能力 1).具备识读焊接装配图、绘制简单零件图的能力,具备利用计算机处理图样的能力。 2).掌握金属材料及热处理的基础知识。 3).具备焊接冶金的基础知识,掌握金属材料的焊接性能。 4).掌握常用焊接方法和焊接设备的基本知识。 5).具备选择并实施焊接工艺的能力。 6).掌握普通焊接的操作技能,并取得焊工(中级)职业资格证书。 7).具备选择检验部位、检验方法及分析和处理焊接缺陷的基本能力。 8).具备从事焊接设备及焊接材料营销与售后服务的能力。 9).具备使用与维护的焊接设备能力。 10).具备焊接生产管理与组织的基本知识。 六、课程设置 1.公共基础课
n-well diode n阱二极管 nack (negative acknowledgement) 否定应答 name server 名称服务器 nano- (n) 毫微:纳 nanobot毫微瓦,纳级泥塞 nanocode纳代码 nanoinstruction纳指令 nanometer (nm) 毫微米 nanophase materials 纳相材料 nanosecond (ns) 毫微秒 nanotechnology 纳(10-9 ) 技术 narrow band 窄频带 narrow-band amplifier 窄频放大器 narrow-band axis 窄频轴 narrow-band filter 窄频带滤波器 national ISDN-1 国家综合业务数字网-1 national center for supercomputing applications (NCSA) 国家超级计算应用中心, 国家计算中心 national society of cable television engineers (nscte) 国家有线电视工程师协会 nationwide paging network 全球寻呼网络 natural air cooling 自然空气冷却 natural frequency 自然频率 natural glitch filter 自然干扰过滤器 natural oscillation 自然振荡 navigation 导引;导航 navigation software 导引软体;导航软体 near infrared 近红外线 near video on demand (NVOD) 近似视频点播,仿视频点播 near-body capacitance 近体电容 near-end crosstalk 近端交越干扰 near-letter quality 接近优质字符 near-letter-quality printing 接近优质字符打印 nearly instantaneous companded audio multiplexing(NICAM) 近瞬时压缩扩展音频多工技术;丽音广播系统 negate 否定;非 negation 否定;非 negative acknowledge character 否认字符 negative bias 负偏压 negative charge 负电荷 negative electrode 负电极 negative feedback 负反馈 negative gate drive 非门驱动 negative ion 负离子 negative logic 负逻辑
隧道专业英汉词典
十、隧道专业汉英英汉常用词汇
汉英部分 20号钢筋混凝土M 20 reinforced concrete H橡皮H-shaped rubber n值n-value T形钢板T-steel plate U形钢支撑U-shaped steel support X射线结构分析x-ray analysis of fabric; x-ray structure analysis A 安全safety 安全灯safety lamp 安全等级safety class 安全检查safety inspection 安全屏蔽safety screening 安全设备safety device; safety equipment 安全设施safety device; safety equipment 安全通道safety pathway; safety walkway 安全通路safety pathway; safety walkway 安全卫生管理体制safety and health control system 安全系数safety factor 安全巡查safety patrol 安全巡检safety patrol 安全巡逻车safety patrol car 安全闸emergency lock 安全炸药safety explosive; permitted explosive 安全装置safety apparatus; safety device 安装功率installed power 安装孔洞installation recess 安装图installation diagram; assembly diagram 安装位置installation place; mounting position 暗沟underdrain; blind ditch; blind drain 暗榫式对接straight joint 暗挖法under-cutting method; mining method 奥陶纪Ordovician B 扒碴机gathering loader 扒斗铲泥机slusher 白垩纪Cretaceous 白色涂料white plastering
桥梁与隧道工程专业本科生求职信 桥梁与隧道工程专业本科生求职信 尊敬的领导: 您好! 衷心地感谢您在百忙之中垂阅此信,为一位满腔热情的大学生开启了一扇希望之门!怀着对贵公司积极进取精神的敬慕和对美好未来的憧憬,谨向贵公司发出这封求职信,请允许我毛遂自荐。很荣幸您能在百忙之中翻阅我的求职信。 我能够给贵公司写出我的求职信,那我就已经做好了心理准备,既有不被录取的心理准备,也有将要被录取的心理准备,这样才不会失去常态,时刻做到心中有数。 我是一名20XX届本科生,就读于教育部直属重点大学-----xx 交通大学,我的姓名是xx,所读专业是桥梁与隧道工程、在校期间我刻苦学习,严格遵守学校的规章制度,社会公德,尊敬师长,团结同学乐于助人,在德,智,体,美,劳方面得到全面发展、通过我的努力,我在专业课的学习上每年获得学校的奖学金,凭着优异的成绩进入了学校的辅修专业课程《心得体会计算机网络》的学习,同样以优良的成绩圆满毕业,能连接局域网及interne的接入、在校期间我还利用业余时间学习了许多计算机知 识,word,autocad,photoshop,及c语言,汇编语言,html等都得以学习和掌握、特别是对word,autocad的应用分熟练、我已经具备
了计算机操作的基本能力,并且坚信会在计算机应用及编程方面创造出一片蔚蓝的天空、 英语是我擅长的科目之一,通过了全国大学英语四级考试,我在英语阅读与写作上更显优势,借助词典能阅读翻译专业型英文资料,总之我有着相当的英语水平、 平时我的课余活动也分广泛,乒乓球,篮球,羽毛球等球类运动都是我的爱好,还喜欢阅读书籍,这主要是为了培养艺术能力,有艺术才会树立好形象,才能用计算机设计出代表个人,企事业单位的好标志、最后,请领导核实我的情况,相信我,我会在您给我提供的舞台上献上最美的舞姿,希望领导接纳我,我愿我一生的勤勉报答贵单位!我愿与您携手共进!再次感谢您对我的关注、 我相信虽然我是迎接毕业生,工作总结 但是我有着初生牛犊不怕虎的精神,我可以没有任何压力的投入到工作中去,我也可以没有那些已婚人员的浮躁心理,我所做的就是要做好工作,没有任何的杂念。 我也希望贵公司能够看到我想加入到贵公司的迫切之心,如果我加入贵公司,我一定会在公司给我的小小平台上做出自己的最大努力,在公司的工作岗位上发光发热。 如果贵公司不录取我,只能说明我的能力达不到贵公司的要求,我会在以后的生活学习中继续努力的,我相信我会做好的。 此致 敬礼!
Absorber Circuit ——吸收电路 AC/AC Frequency Converter ——交交变频电路 AC power control ——交流电力控制 AC Power Controller ——交流调功电路 AC Power Electronic Switch ——交流电力电子开关 Ac V oltage Controller ——交流调压电路 Asynchronous Modulation ——异步调制 Baker Clamping Circuit ——贝克箝位电路 Bi-directional Triode Thyristor ——双向晶闸管 Bipolar Junction Transistor-- BJT ——双极结型晶体管Boost-Buck Chopper ——升降压斩波电路 Boost Chopper ——升压斩波电路 Boost Converter ——升压变换器 Bridge Reversible Chopper ——桥式可逆斩波电路 Buck Chopper ——降压斩波电路 Buck Converter ——降压变换器 Commutation ——换流 Conduction Angle ——导通角 Constant V oltage Constant Frequency --CVCF ——恒压恒频Continuous Conduction--CCM ——(电流)连续模式 Control Circuit ——控制电路 Cuk Circuit ——CUK斩波电路 Current Reversible Chopper ——电流可逆斩波电路Current Source Type Inverter--CSTI ——电流(源)型逆变电路Cycloconvertor ——周波变流器 DC-AC-DC Converter ——直交直电路 DC Chopping ——直流斩波 DC Chopping Circuit ——直流斩波电路 DC-DC Converter ——直流-直流变换器 Device Commutation ——器件换流 Direct Current Control ——直接电流控制 Discontinuous Conduction mode ——(电流)断续模式displacement factor ——位移因数 distortion power ——畸变功率 double end converter ——双端电路 driving circuit ——驱动电路 electrical isolation ——电气隔离 fast acting fuse ——快速熔断器 fast recovery diode ——快恢复二极管
A Type Wooden Ladder A字木梯 A-frame A型骨架 A-truss A型构架 Aandon 废弃 Abandoned well 废井 Aberration of needle 磁针偏差Abnormal pressure 异常压力abnormally high pressure 异常高压Abort 中止 abrasion 磨损 Abrasion surface 浪蚀面 abrasive cut-off machine 磨切机Abrasive Cutting Wheel 拮碟abrasive grinding machine 研磨机Abrasive Grinding Wheel 磨碟abrasive particle 磨料颗粒Absolute address 绝对地址Absolute altitude 绝对高度Absolute damping 绝对阻尼Absolute deviation 绝对偏差Absolute flying height 绝对航高Absolute gravity 绝对重力 absolute permeability 绝对渗透率absolute porosity 绝对孔隙率absolute temperature 绝对温度absorbability 吸收性;吸附性absorption 吸收 abutment 桥墩 abutting end 邻接端 acceleration 加速 acceleration lane 加速车道Acceleration of gravity 重力加速度acceleration pedal 加速器踏板accelerator 催凝剂;加速器;催化剂acceptance criteria 接受准则access 通路;通道 access door 检修门;通道门access lane 进出路径 access panel 检修门 access point 入口处;出入通道处access ramp 入口坡道;斜通道access road 通路;通道 access shaft 竖井通道 access spiral loop 螺旋式回旋通道access staircase 通道楼梯 access step 出入口踏步 access tunnel 隧道通道 accessible roof 可到达的屋顶 accessory 附件;配件 accident 事故;意外 accidental collapse 意外坍塌accommodate 装设;容纳 accredited private laboratory 认可的私人实验室 accumulator 储压器;蓄电池 accuracy limit 精度限制 acetylene cylinder 乙炔圆筒 Acetylene Hose 煤喉 Acetylene Regulator 煤表 acid plant 酸洗设备;酸洗机 acid pump 酸液泵 acid tank 酸液缸 acidic rock 酸性岩 acoustic couplant 声耦合剂 acoustic coupler 声音藕合器;音效藕合器acoustic lining 隔音板 acoustic screen 隔声屏 Acoustic wave 声波 acrylic paint 丙烯漆料(压克力的油漆) acrylic sheet 丙烯胶片(压克力的胶片) active corrosion 活性腐蚀 active earth pressure 主动土压力 active fault 活断层 active oxidation 活性氧化 actual plot ratio 实际地积比率 actuator 促动器;唧筒;激发器 adapt 改装 adaptor 适配器;承接器;转接器;addition 增设;加建 additional building works 增补建筑工程additional horizontal force 额外横向力additional plan 增补图则(附加的平面图) additional vent 加设通风口 additive 添加剂 Address 地址 adhesive 黏结剂;胶黏剂 adhesive force 附着力 Adhesive Glue 万能胶
(表记录的)插入修改添加删除InsertModify, updateAddDelete (拨号后)拨号音不断 Non-stop Dial Tone (程序,进程)调度 Dispatch (程序安装的)序列号 Serial Number SN (单板)不在位 Not-in-position (单板等)插入/拔出 Plug/Unplug (发货)附件,辅助设备 Accessories (话务员)为分机用户代拨外线 Dial Out For An Extension (话务员帮)接通(电话) Put Through (计算机上)主板,母板 Mother-Board (界面)刷新 Refresh (开局)调测现场 Commissioning Site (判定)门限 Threshold (软件)补钉 Patch (试运行前的)开通调测 Commissioning PG (相)邻(信)道干扰 Adjacent-channel interference (移动电话)交接,越区切换 Handover (用户线)主配线架 Main Distribution Frame MDF (中继的)监听、插入及强拆 Monitor, Intrusion and Forced Release 1800MHz频段的数字蜂窝系统 Digital Cellular System at 1800MHz DCS1800 2B1Q线路码 Two Binary-To-One Quaternary Line Code 2B1Q 2M数字分支板 2Mb/s Digital Branching Board DB2M 3 型不对称数字用户线 ADSL-3 3阶高密度双极性码 High Density Bipolar of Order 3 HDB3 50W粗缆10Mb/s基带以太网 10Base 5 50W细缆10Mb/s基带以太网 10Base 2 500伏兆欧表(测绝缘电阻用 500V Meg-ohmmeter (used to measure the insulation resistance) 5合1拼板 5 In 1 Board a. (窗口)缩放 b. 放大 c. 缩小 d.最大化 e.最小化 ZoomZoom inZoom outMaximizeMinimize a.板,祼板 b.板卡,单板 BoardCard a.本地网 b.本地通讯网 c.局域网 Local NetworkLocal Communication NetworkLocal Area Network LNLCNLAN a.本局(交换局) b.本局(交换、传输等通用) Home exchangeHome office a.处理(呼叫,通信) b.处理(问题、意外) c.对待 ProcessingHandlingTreatment a.单选框 b.复选框 c.组合框 Button boxCheck boxCombo box a.对话处理 b.会话处理 Dialogue HandlingSession processing DHA a.对接 b.互通 InterconnectionInterworking a.高清晰度电视 b.高分辩率电视 High Definition TelevisionHigh Resolution Television HDTV a.挂起 b.恢复(被挂起的) SuspendResume RES a.火线 b.零线 Live LineZero Line a.局(交换) b.局(交换、传输等通用) ExchangeOffice a.可选的 b.必选的 c.必须的,必须遵循的,强制性的 OptionalCompulsoryMandatory a.拉手条(单板) b.空面板(单板) Handle BarBlank Panel a.配件 b.部件 c.组件 d.附件 e.备件 FittingsPartsComponentsAccessoriesSpare Parts a.配置 b.分配 c.指配(几个词在不同产品可能用法不一样) ConfigurationAllocation, DistributionProvisioning, Assignment a.起始 b.终止 StartEnd POI a.试运行 b.割接 Trial RunCut-over a.双绞线 b.非屏蔽双绞线 c.屏蔽双绞线 d.同轴电缆 e.同轴细缆 f.同轴粗缆 Twisted PairUnshielded Twisted PairShielded Twisted PairCoaxial cable Thicknet (cable) UTPSTP a.文件服务器 b.应用程序服务器 c.列表服务器 File ServerApplication ServerList Server FNS a.优先(用户) b.普通 c.立即 Prior OrdinaryImmediate a.增殖业务 b.新业务 Value Added Service (VAS)New Service A/B线 A Wire/B Wire AB04 A/B线中继 A Wire/B Wire Trunk ABT A/D,D/A混合转换器 A/D And D/A Combined Converter ADSL-高速因特网接入 ADSL-High-Speed Internet Access ASIC及专用电路芯片 ASIC And Special Chips ATM 适配层 ATM Adaptation Layer AAL A通道 A channel BCCH(频率)分配 BCCH Allocation BA BNC T型接头 BNC T Connector BNC同轴插拔头 BNC Connector BNC同轴插拔头(阳) BNC Male Connector BNC同轴插拔头(阴) BNC Female Connector BNC终接器 BNC Terminator BSS操作维护应用部分 BSS Operation and Maintenance Application Part BSSOMAP BTS的站址管理 BTS Address Management BTSM BTS管理 Base Transceiver Station Management BTSM B通道顺序号 B channel sequence number BSN B型机机柜 C&C08 B Cabinet CAMEL应用部分 CAMEL Application Part CAP CATV相关配件 CATV Related Fittings D-Link 说明书 D-link Specifications D-Link 网络驱动软盘 D-link Network Drive Floppy Disk D通道链路接入协议 Link Access Protocol for D channel LAPD