10吨中频炉技术参数英文翻译对照

化工设备常用词汇和缩写中英文对照缩写/ 英文/中文AB Anchor Bolt 地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium 铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会ASME American Society of Mechanical Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure 大气压Auto Automatic 自动Aux Auxiliary 辅助设备、辅助的A vail A vailable 有效的、可用的A vg A verage 平均A W Arc welding 电弧焊A W Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规A WS(A WI) American Welding Society(Institute) 美国焊接学会BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距BC Bolt circle 螺栓中心圆BD Blow down 放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在…之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit 界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表Bskt Basket 筐BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly V alve 碟阀BW Brine V ater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost，Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate 冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Compn Composition 组分Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure 压力中心Cpl Coupling 管箍Cplg Coupling 联轴节CR Chloroprene Rubber 氯丁橡胶CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒D Density 密度Dbl Double 二倍、双DEDD Detail Engineering Design Data 详细工程设计数据Def Definition 定义Deg Degree 度、等级Dept Department 部门Des Design 设计Det Detail 详细Detn Determination 确定、决定Dev Deviation 偏差Dev Device 装置DF Design Formula 设计公式Df Deflection 偏斜Dia Diameter 直径Diag Diagram 图Dim Dimension 尺寸Dir Direction 方向Disch Discharge 排出、出口Distr Distribution 分布Div Division 部分、区分DL Dead load 静载荷、自重Doc Document 文件、资料DP Design Pressure 设计压力DP Differential Pressure 压差、分压Dr Drill 钻孔Dr Drive 驱动DW Dead weight 静重、自重DW Demineralized Water 脱盐水Dwg Drawing 图E East 东EC Elasticity Coefficient 弹性系数Ecc Eccentric 偏心EF Electric Furnace 电炉Eff Efficiency 效率eg exempli gratia 例如EHP Effective Horsepower 有效功率EJ Expansion joint 膨胀节EL Elevation 标高Elb Elbow 弯头Elec Electric 电的Elem Element 元素、元件Ellip Ellipsoidal 椭球的、椭圆的Emer、Emerg Emergency 事故、紧急Encl Enclosure 密封、封闭Engrg、Eng Engineering 工程、设计EP Explosion Proof 防爆Eq Equipment 设备Eq Equation 公式、方程式Eq Equivalent 当量ES Electrostatic 静电EST Estimate 估计ESW Electro-Slag Welding 电渣焊ET Eddy Current Examination 涡流检验etc et cetera (and so on) 等等Evap Evaporate 蒸发Ex Example 例如Ex Excess 过剩、超过Exam Examination 检验Exh Exhaust 废气、排气Exp Expansion 膨胀Exptl Experimental 实验的Ext External 外部Ext Extreme 极端的FAO Finish All Over 全部加工FAX Facsimile 传真FB Flat Bar 扁钢FCA W Flux Cored Arc Welding 熔剂芯弧焊（手工焊）Fdn Foundation 基础FDW Feed Water 给水FF Flat Face 平面F/F Field Fabricated 现场制造Fig Figure 图Fin Finish 加工、完成FL Full Load 满载Flex Flexible 挠性Flg Flange 法兰FOB Free On Board 离岸价格FOC Free Of Charge 免费Forg Forging 锻件FOS Factor Of Safety 安全系数FREQ Frequency 频率FST Forged Steel 锻钢Ft Feet 英尺Ftg Fitting 管件、装配F.V. Full V acuum 全真空FW Fresh Water 新鲜水FW Field Weld 现场焊接FW Fillet Weld 角焊缝GA General A verage 平均值Gal Gallon 加仑Gen General 一般、总的Genr Generator 发电机、发生器GF Groove Face 槽面Gl Glass 玻璃GL Ground Level 地面标高GMA W Gas Metal Arc Welding 气体保护金属极电弧焊Gnd Ground 接地、地面Govt Government 政府GP General Purpose 一般用途、通用Gr Grade 等级Gr Gravity 重力Grd Ground 地面Grp Group 分组、类Gr- wt Gross weight 总重、毛重HB Brinell Hardness 布氏硬度HC Hydrocarbon 烃类HC High Capacity 大容量HD Head 压头Hex Hexagon 六角HH Hand Hole 手孔Hor Horizontal 水平、卧式hp Horsepower 马力HP High Pressure 高压HR Rockwell Hardness 洛氏硬度HR(hr) Hour 小时HRC Rockwell C Hardness C级洛氏硬度HS High Pressure Steam 高压蒸汽HS Shore Scleroscope Hardness 肖氏硬度HSC High Pressure Condensate 高压蒸汽凝液HT High Temperature 高温HT Heat Treatment 热处理HT Hydrostatic Test 水压试验HV V ickers Hardness 维氏硬度Hvy Heavy 重的、重型的HW Hot Water 热水ICW Inter Cooling Water 中间冷却水ID Inside Diameter 内径IF Interface 交接面Illus Illustration 说明、图解IN Inlet 进口in Inch 英寸incl Including 包括Ind Indicate 指示Ins Insulation 保温INSP Inspection 检验Instl Installation 安装Int Internal 内部的Int Intermediate 中间的Intmt Intermittent 间歇的、间断的I/O Input/Output 输入/输出Jt Joint 连接、接头KG Kilogram 公斤KW(kw) Kilowatt 千瓦LAS Low Alloy Steel 低合金钢lb pound 磅LC Level Control 液位控制器Leng Length 长度LF Female Face 凹面Lg Long 长的LG Level Glass 液位计LH Left Hand 左手Lin Linear 线性的Liq Liquid 液体Lj Lap joint 搭接LJ Lapped Joint 松套LM Male Face 凸面LMTD Logarithmic Mean Temperature Difference 对数平均温差LN Liquid Nitrogen 液氮LN Level Normal 正常液位Lng Lining 衬里LNG Liquefied Natural Gas 液化天然气Lo Lubrication oil 润滑油Lo Low 低LOA Length Over-All 全长\总长LOC Location 位置Log Logarithm(to the base 10) 对数（以10为底）Long Longitudinal 纵向LP Low Pressure 低压LPG Liquefied Petroleum Gas 液化石油气LT Low Temperature 低温LT Leak Testing 气密试验Ltd Limited 有限Ltr Letter 字母、信Lub Lubricate 润滑LW Lap Welding 搭接焊LWN Long Welding Neck 对焊长颈LWS Longitudinal Welded Seam 纵向焊缝M(m) Meter 米、公尺Mach Machine 机器Maint Maintenance 维修Mat(Mat’l) Material 材料MAWP Maximum Allowable Working Pressure 最大允许工作压力Max Maximum 最大MDMT Min. Design Metallic Temperature 最低设计金属温度Mech Mechanical 机械的Mfd Manufactured 制造的Mfr Manufacturer 制造商MG(mg) Milligram 毫克MH Manhole 人孔MI Melt Index 熔融指数MIG Metal Inert Gas Arc Welding 熔化极惰性气体保护焊Min Minimum 最小MIN(min) Minute 分钟MJG Metallic Jacketed Gasket金属包复垫片Mk Mark 标志ml Milliliter 毫升mm Millimeter 毫米MP Medium Pressure 中压MPC Maximum Permissible Concentration 最大许用浓度MS Medium Pressure Steam 中压蒸汽MS Medium Steel 中碳钢MSL Mean Sea Level 平均海平面MT Magnetic Particle Examination 磁粉检测MTD Mean Temperature Difference 平均温差Mtd Mounted 安装、装配MTR Material Testing Report 材料试验报告MU Measurement Unit 测量单位MV Mean V alue 平均值MW Mineral Wool 矿渣棉N North 北NA Not Applicable 不适用的NA T Natural 天然的Natl National 国家的NC America National Coarse Thread 美制粗牙螺纹NDT Nondestructive Testing 无损检验Neg Negative 负NF American National Fine Thread 美国细牙螺纹Nip Nipple 螺纹管接头、短节Nom Nominal 名义Nor Normal 正常NOZ Nozzle 接管NPS American Standard Straight Pipe Thread 美国标准直管螺纹NPSHA Net Positive Suction Head A vailable 有效汽蚀裕量NPSHR Net Positive Suction Head Required 要求汽蚀裕量NPT American Standard Taper Pipe Thread 美国标准锥管螺纹NT Net Tonnage 净吨数NTP Normal Temperature and Pressure 标准温度和压力NTS Not To Scale不按比例Num Number 数、编号、号码Obj Object 目标、对象OC Operating Characteristic 操作特性OD Outside Diameter 外径OH Open Hearth 平炉Oper Operating 操作Opp Opposite 对面、相反OR Outside Radius 外半径OR Outside Ring 外环Orien Orientation 方位Ovhd Overhead 高架的、顶部的Oxyg Oxygen 氧P Page 页P Pressure 压力Par Parallel 平行Para Paragraph 节、段Pc Piece 件PE Polyethylene 聚乙烯PFD Process Flow Diagram 工艺流程图Perform Performance 性能PF Power Factor 功率因素PID Piping & Instruments Diagram 管道和仪表流程图Pl Plate 板Pneum Pneumatic 气、气动PO Purchase Order 订货单Port Portable 便携式、轻便Posit Positive 正Posit Position 位置ppb Parts per billion 十亿分之几ppm Parts per million 百万分之几Prod Product 产品Proj Project 项目、工程PS Polystyrene 聚苯乙烯psf Pounds per square feet 磅/平方英尺psi Pounds per square inch 磅/平方英寸PT Liquid Penetrants Examination 液体渗透检测PTFE Polytetrafluoroethylene 聚四氟乙烯PV A Polyvinyl Acetate 聚醋酸乙烯PV AL Polyvinyl Alcohol 聚乙烯醇PVC Polyvinyl Chloride 聚氯乙烯PWHT Post Weld Heat Treatment 焊后热处理QA Quality Assurance 质量保证QC Quality Control 质量控制Qty Quantity 数量Qual Quality 质量R Radius 半径Rad Radial 径向RC Rockwell Hardness 洛氏硬度Recip Reciprocate 往复式Recirc Recirculate 再循环Recom Recommended 建议、推荐Ref Reference 参照、基准Refract Refractory 耐火材料Reg Regulator 调节器Regen Regenerator 再生器、再生塔Reinf Reinforce 加强Rel Relative 相对Rep Report 报告Rep Repeat 重复Reqd Required 要求、需要的REV Revision 修改、版次Rev Review 评论、检查Rev Revolution 旋转、转数RF Raise face 突台面RH Relative Humidity相对湿度RH Right Hand 右手RMS Root Mean Square 均方根ROT Rotating 旋转rpm revolutions per minute 转/分rps revolutions per second 转/秒RT Radiographic Examination 射线照相检验S South 北SA W Submerged Arc Welding 埋弧焊Sc Scale 刻度、比例SC Standard Condition 标准状态（温度压力）SCH Schedule 表号、管厚号、进度Sec Second 秒Sec Section 剖面、节、段Seg Segment 节、段Sep Separator 分离器Seq Sequence 次序、顺序SG Specific Gravity 比重SHP Shaft Horsepower 轴马力SI Standard International 国际单位制Sig Signal 信号Sld Solid 固体SMA W Shield Metal Arc Welding 手工焊Smls Seamless 无缝的SO Slip on 平焊（法兰）Sol Solution 溶液SP Spare parts 备件Sp Special 特殊的、专门的SP Static pressure 静压力Spec Specification 说明、规定SpGr Specific Gravity 比重Sq Square 方形、平方SR Stress Relief 消除应力SS Stainless Steel 不锈钢Sta Station 站STD Standard 标准STDWT Standard Weight 标准重量STL Steel 钢STP Standard Temperature and Pressure 标准温度和压力Suc Suction 吸入Suppl Supplement 补充SW Shop Welding 车间焊接SW Spot Weld 点焊SW Socket Welding 承插焊（法兰）SWP Safety Working Pressure 安全工作压力SYM Symbol 符号、标志SYM Symmetry 对称SYS System 系统T Ton 吨TC Tungsten Carbide 碳化钨Tech Technique 技术TEMA Tubular Exchanger Manufacturers Association 管壳式换热器制造商协会（美国）Temp Temperature 温度Term Terminal 终端、接头Thk Thickness 厚度TIG Tungsten Inert Gas Arc Welding 钨极惰性气体保护焊TL Tangent line 切线Tol Tolerance 公差Tot Total 总Trans Transfer 输送器TW Total Weight 总重TW Tack Welding 定位焊Typ Typical 典型、标准UNC Unified National Coarse Thread 统一标准粗牙螺纹UNF Unified National Fine Thread 统一标准细牙螺纹US Undersize 尺寸过小UT Ultrasonic Examination 超声波探伤UTS Ultimate Tensile Strength 抗拉强度极限V ac V acuum 真空V ap V apor 蒸汽V ar V ariable 变化、变量V el V elocity 速度V ert V ertical 垂直V ol V olume 体积VT Visual Testing 宏观（目测）检查W Watt 瓦WL Welding Line 焊缝线WL Water Line 水线WPS Welding Procedure Specification 焊接工艺规程WP Working Pressure 工作压力WRC Welding Research Committee 焊接研究委员会（美国）WS Water Supply 供水WT Weight 重量W/V Wind V elocity 风速XR X-Ray X射线Yd Y ard 码YP Yield Point 屈服点Yr Year 年。

英文说3吨中频炉3吨中频炉3-ton intermediate frequency furnace由标准配置或加强配置2500KW中频电源1套配3吨中频感应加热炉两台用于铸钢熔炼炉。

designed standard or enhanced set of2500KW intermediate frequency power source,with two3-ton intermediate frequency induction heating furnace for steel melting。

一、3吨中频炉技术参数设备配置(12脉中频炉）设备型号GWT-3/2500技术指标（加强配置）技术指标（标准配置）设备额定功率2500KW1500KW进相电压3*950V3*660V电炉额定电压3200V2500V额定容量3T3T额定温度1600℃1600℃成套配置快速12脉中频电源一套一套西安东新机电制造有限公司作者:康忠波永鑫电炉城站长单：补偿电容柜一套（电容16台）一套（电容12台）中频炉（炉壳Φ1600，感应圈铜管30*60*4）二台二台减速机二台二台水冷电缆四根两根坩埚膜一只一只说明书资料一份一份维修保修期1年1年备注：1）用6相12脉中频电源。

消除了5、7高次谐波，大大减少了电网的谐波干扰。

2）采用全封闭式冷却塔提可提高系统的冷却效果和设备的使用寿命，无须建水池。

3-ton intermediate frequency furnace technical parameters(12pulse)Model GWT-3/2500Index（Enhanced）Index（Standard）西安东新机电制造有限公司作者:康忠波永鑫电炉城站长Rated power2500KW1500KW Phase voltage3*950V3*660V Rated voltage3200V2500V Rated capacity3T3T Rated temperature1600℃1600℃Complete configuratio n：Fast12pulse intermediate frequencypower sourceA set A setCompensation capacitor A set(16Capacitance)A set(12Capacitance) Intermediate frequencyfurnace(furnace shellΦ1600,theInduction coil copper tube30*60*4)Two TwoReducer Two TwoWater cooled cables FOUR Two西安东新机电制造有限公司作者:康忠波永鑫电炉城站长Crucible film One OneInstructions for use One OneWarranty period1year1yearPrice1）6phase12pulse intermediate frequency power source.Eliminate5,7high-order harmonic，and significantly reduces the power grid harmonic interference。

化工设备常用词汇和缩写中英文对照缩写/ 英文/中文AB Anchor Bolt 地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium 铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会ASME American Society of Mechanical Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure 大气压Auto Automatic 自动Aux Auxiliary 辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American Welding Society(Institute) 美国焊接学会BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距BC Bolt circle 螺栓中心圆BD Blow down 放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在…之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit 界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表Bskt Basket 筐BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve 碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost，Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate 冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Compn Composition 组分Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure 压力中心Cpl Coupling 管箍Cplg Coupling 联轴节CR Chloroprene Rubber 氯丁橡胶CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒D Density 密度Dbl Double 二倍、双DEDD Detail Engineering Design Data 详细工程设计数据Def Definition 定义Deg Degree 度、等级Dept Department 部门Des Design 设计Det Detail 详细Detn Determination 确定、决定Dev Deviation 偏差Dev Device 装置DF Design Formula 设计公式Df Deflection 偏斜Dia Diameter 直径Diag Diagram 图Dim Dimension 尺寸Dir Direction 方向Disch Discharge 排出、出口Distr Distribution 分布Div Division 部分、区分DL Dead load 静载荷、自重Doc Document 文件、资料DP Design Pressure 设计压力DP Differential Pressure 压差、分压Dr Drill 钻孔Dr Drive 驱动DW Dead weight 静重、自重DW Demineralized Water 脱盐水Dwg Drawing 图E East 东EC Elasticity Coefficient 弹性系数Ecc Eccentric 偏心EF Electric Furnace 电炉Eff Efficiency 效率eg exempli gratia 例如EHP Effective Horsepower 有效功率EJ Expansion joint 膨胀节EL Elevation 标高Elb Elbow 弯头Elec Electric 电的Elem Element 元素、元件Ellip Ellipsoidal 椭球的、椭圆的Emer、Emerg Emergency 事故、紧急Encl Enclosure 密封、封闭Engrg、Eng Engineering 工程、设计EP Explosion Proof 防爆Eq Equipment 设备Eq Equation 公式、方程式Eq Equivalent 当量ES Electrostatic 静电EST Estimate 估计ESW Electro-Slag Welding 电渣焊ET Eddy Current Examination 涡流检验etc et cetera (and so on) 等等Evap Evaporate 蒸发Ex Example 例如Ex Excess 过剩、超过Exam Examination 检验Exh Exhaust 废气、排气Exp Expansion 膨胀Exptl Experimental 实验的Ext External 外部Ext Extreme 极端的FAO Finish All Over 全部加工FAX Facsimile 传真FB Flat Bar 扁钢FCAW Flux Cored Arc Welding 熔剂芯弧焊（手工焊）Fdn Foundation 基础FDW Feed Water 给水FF Flat Face 平面F/F Field Fabricated 现场制造Fig Figure 图Fin Finish 加工、完成FL Full Load 满载Flex Flexible 挠性Flg Flange 法兰FOB Free On Board 离岸价格FOC Free Of Charge 免费Forg Forging 锻件FOS Factor Of Safety 安全系数FREQ Frequency 频率FST Forged Steel 锻钢Ft Feet 英尺Ftg Fitting 管件、装配F.V. Full Vacuum 全真空FW Fresh Water 新鲜水FW Field Weld 现场焊接FW Fillet Weld 角焊缝GA General Average 平均值Gal Gallon 加仑Gen General 一般、总的Genr Generator 发电机、发生器GF Groove Face 槽面Gl Glass 玻璃GL Ground Level 地面标高GMAW Gas Metal Arc Welding 气体保护金属极电弧焊Gnd Ground 接地、地面Govt Government 政府GP General Purpose 一般用途、通用Gr Grade 等级Gr Gravity 重力Grd Ground 地面Grp Group 分组、类Gr- wt Gross weight 总重、毛重HB Brinell Hardness 布氏硬度HC Hydrocarbon 烃类HC High Capacity 大容量HD Head 压头Hex Hexagon 六角HH Hand Hole 手孔Hor Horizontal 水平、卧式hp Horsepower 马力HP High Pressure 高压HR Rockwell Hardness 洛氏硬度HR(hr) Hour 小时HRC Rockwell C Hardness C级洛氏硬度HS High Pressure Steam 高压蒸汽HS Shore Scleroscope Hardness 肖氏硬度HSC High Pressure Condensate 高压蒸汽凝液HT High Temperature 高温HT Heat Treatment 热处理HT Hydrostatic Test 水压试验HV Vickers Hardness 维氏硬度Hvy Heavy 重的、重型的HW Hot Water 热水ICW Inter Cooling Water 中间冷却水ID Inside Diameter 内径IF Interface 交接面Illus Illustration 说明、图解IN Inlet 进口in Inch 英寸incl Including 包括Ind Indicate 指示Ins Insulation 保温INSP Inspection 检验Instl Installation 安装Int Internal 内部的Int Intermediate 中间的Intmt Intermittent 间歇的、间断的I/O Input/Output 输入/输出Jt Joint 连接、接头KG Kilogram 公斤KW(kw) Kilowatt 千瓦LAS Low Alloy Steel 低合金钢lb pound 磅LC Level Control 液位控制器Leng Length 长度LF Female Face 凹面Lg Long 长的LG Level Glass 液位计LH Left Hand 左手Lin Linear 线性的Liq Liquid 液体Lj Lap joint 搭接LJ Lapped Joint 松套LM Male Face 凸面LMTD Logarithmic Mean Temperature Difference 对数平均温差LN Liquid Nitrogen 液氮LN Level Normal 正常液位Lng Lining 衬里LNG Liquefied Natural Gas 液化天然气Lo Lubrication oil 润滑油Lo Low 低LOA Length Over-All 全长\总长LOC Location 位置Log Logarithm(to the base 10) 对数（以10为底）Long Longitudinal 纵向LP Low Pressure 低压LPG Liquefied Petroleum Gas 液化石油气LT Low Temperature 低温LT Leak Testing 气密试验Ltd Limited 有限Ltr Letter 字母、信Lub Lubricate 润滑LW Lap Welding 搭接焊LWN Long Welding Neck 对焊长颈LWS Longitudinal Welded Seam 纵向焊缝M(m) Meter 米、公尺Mach Machine 机器Maint Maintenance 维修Mat(Mat’l) Material 材料MAWP Maximum Allowable Working Pressure 最大允许工作压力Max Maximum 最大MDMT Min. Design Metallic Temperature 最低设计金属温度Mech Mechanical 机械的Mfd Manufactured 制造的Mfr Manufacturer 制造商MG(mg) Milligram 毫克MH Manhole 人孔MI Melt Index 熔融指数MIG Metal Inert Gas Arc Welding 熔化极惰性气体保护焊Min Minimum 最小MIN(min) Minute 分钟MJG Metallic Jacketed Gasket 金属包复垫片Mk Mark 标志ml Milliliter 毫升mm Millimeter 毫米MP Medium Pressure 中压MPC Maximum Permissible Concentration 最大许用浓度MS Medium Pressure Steam 中压蒸汽MS Medium Steel 中碳钢MSL Mean Sea Level 平均海平面MT Magnetic Particle Examination 磁粉检测MTD Mean Temperature Difference 平均温差Mtd Mounted 安装、装配MTR Material Testing Report 材料试验报告MU Measurement Unit 测量单位MV Mean Value 平均值MW Mineral Wool 矿渣棉N North 北NA Not Applicable 不适用的NAT Natural 天然的Natl National 国家的NC America National Coarse Thread 美制粗牙螺纹NDT Nondestructive Testing 无损检验Neg Negative 负NF American National Fine Thread 美国细牙螺纹Nip Nipple 螺纹管接头、短节Nom Nominal 名义Nor Normal 正常NOZ Nozzle 接管NPS American Standard Straight Pipe Thread 美国标准直管螺纹NPSHA Net Positive Suction Head Available 有效汽蚀裕量NPSHR Net Positive Suction Head Required 要求汽蚀裕量NPT American Standard Taper Pipe Thread 美国标准锥管螺纹NT Net Tonnage 净吨数NTP Normal Temperature and Pressure 标准温度和压力NTS Not To Scale 不按比例Num Number 数、编号、号码Obj Object 目标、对象OC Operating Characteristic 操作特性OD Outside Diameter 外径OH Open Hearth 平炉Oper Operating 操作Opp Opposite 对面、相反OR Outside Radius 外半径OR Outside Ring 外环Orien Orientation 方位Ovhd Overhead 高架的、顶部的Oxyg Oxygen 氧P Page 页P Pressure 压力Par Parallel 平行Para Paragraph 节、段Pc Piece 件PE Polyethylene 聚乙烯PFD Process Flow Diagram 工艺流程图Perform Performance 性能PF Power Factor 功率因素PID Piping & Instruments Diagram 管道和仪表流程图Pl Plate 板Pneum Pneumatic 气、气动PO Purchase Order 订货单Port Portable 便携式、轻便Posit Positive 正Posit Position 位置ppb Parts per billion 十亿分之几ppm Parts per million 百万分之几Prod Product 产品Proj Project 项目、工程PS Polystyrene 聚苯乙烯psf Pounds per square feet 磅/平方英尺psi Pounds per square inch 磅/平方英寸PT Liquid Penetrants Examination 液体渗透检测PTFE Polytetrafluoroethylene 聚四氟乙烯PV A Polyvinyl Acetate 聚醋酸乙烯PV AL Polyvinyl Alcohol 聚乙烯醇PVC Polyvinyl Chloride 聚氯乙烯PWHT Post Weld Heat Treatment 焊后热处理QA Quality Assurance 质量保证QC Quality Control 质量控制Qty Quantity 数量Qual Quality 质量R Radius 半径Rad Radial 径向RC Rockwell Hardness 洛氏硬度Recip Reciprocate 往复式Recirc Recirculate 再循环Recom Recommended 建议、推荐Ref Reference 参照、基准Refract Refractory 耐火材料Reg Regulator 调节器Regen Regenerator 再生器、再生塔Reinf Reinforce 加强Rel Relative 相对Rep Report 报告Rep Repeat 重复Reqd Required 要求、需要的REV Revision 修改、版次Rev Review 评论、检查Rev Revolution 旋转、转数RF Raise face 突台面RH Relative Humidity 相对湿度RH Right Hand 右手RMS Root Mean Square 均方根ROT Rotating 旋转rpm revolutions per minute 转/分rps revolutions per second 转/秒RT Radiographic Examination 射线照相检验S South 北SAW Submerged Arc Welding 埋弧焊Sc Scale 刻度、比例SC Standard Condition 标准状态（温度压力）SCH Schedule 表号、管厚号、进度Sec Second 秒Sec Section 剖面、节、段Seg Segment 节、段Sep Separator 分离器Seq Sequence 次序、顺序SG Specific Gravity 比重SHP Shaft Horsepower 轴马力SI Standard International 国际单位制Sig Signal 信号Sld Solid 固体SMAW Shield Metal Arc Welding 手工焊Smls Seamless 无缝的SO Slip on 平焊（法兰）Sol Solution 溶液SP Spare parts 备件Sp Special 特殊的、专门的SP Static pressure 静压力Spec Specification 说明、规定SpGr Specific Gravity 比重Sq Square 方形、平方SR Stress Relief 消除应力SS Stainless Steel 不锈钢Sta Station 站STD Standard 标准STDWT Standard Weight 标准重量STL Steel 钢STP Standard Temperature and Pressure 标准温度和压力Suc Suction 吸入Suppl Supplement 补充SW Shop Welding 车间焊接SW Spot Weld 点焊SW Socket Welding 承插焊（法兰）SWP Safety Working Pressure 安全工作压力SYM Symbol 符号、标志SYM Symmetry 对称SYS System 系统T Ton 吨TC Tungsten Carbide 碳化钨Tech Technique 技术TEMA Tubular Exchanger Manufacturers Association 管壳式换热器制造商协会（美国）Temp Temperature 温度Term Terminal 终端、接头Thk Thickness 厚度TIG Tungsten Inert Gas Arc Welding 钨极惰性气体保护焊TL Tangent line 切线Tol Tolerance 公差Tot Total 总Trans Transfer 输送器TW Total Weight 总重TW Tack Welding 定位焊Typ Typical 典型、标准UNC Unified National Coarse Thread 统一标准粗牙螺纹UNF Unified National Fine Thread 统一标准细牙螺纹US Undersize 尺寸过小UT Ultrasonic Examination 超声波探伤UTS Ultimate Tensile Strength 抗拉强度极限Vac Vacuum 真空Vap Vapor 蒸汽Var Variable 变化、变量Vel Velocity 速度Vert Vertical 垂直V ol Volume 体积VT Visual Testing 宏观（目测）检查W Watt 瓦WL Welding Line 焊缝线WL Water Line 水线WPS Welding Procedure Specification 焊接工艺规程WP Working Pressure 工作压力WRC Welding Research Committee 焊接研究委员会（美国）WS Water Supply 供水WT Weight 重量W/V Wind Velocity 风速XR X-Ray X射线Yd Yard 码YP Yield Point 屈服点Yr Year 年。

电力术语中英文对照目录一、集控运行常用设备和术语缩写 (2)（一）锅炉部分 (2)（二）汽机部分 (4)（三）DEH部分 (5)（四）电气部分 (6)（五）系统分类 (6)（六）阀门 (7)（七）其它 (8)二、电厂术语——锅炉部分 (10)三、电厂术语——汽轮机部分 (27)四、电厂术语——电气专业 (59)五、电厂术语——电厂化学 (87)六、电厂术语——仪表与控制 (106)七、电厂术语——燃料 (126)八、电厂术语——综合管理部分 (136)九、电厂术语——脱硫 (165)一、集控运行常用设备和术语缩写（一）锅炉部分1、通用及煤粉炉FDF (forced draft fan)——送风机IDF (induced draft fan)——引风机PAF (primary air fan)——一次风机SAF (seal air fan)——密封风机DETF (flame detector fan)——火检风机APH (air preheater)——空气预热器DRUM (drum)——汽包ECON (economizer)——省煤器SH (superheater)——过热器CSH (ceiling superheater)——顶棚过热器PSH (platen superheater)——屏式过热器RSH (radiation superheater)——辐射过热器LSH (low temperature superheater)——低温过热器HSH (high temperature superheater)——高温过热器RH (reheater) ——再热器LRH (low temperature reheater)——低温再热器HRH (high temperature reheater)——高温再热器PRH (platen temperature reheater)——屏式再热器CB (coal bin)——煤仓SCB(side coal bin)——侧煤仓MILL (mill)——磨煤机FEED (coal feeder)——给煤机PCC (pulverized-coal collector)——细粉分离器MILLS (mill separator)——粗粉分离器PEF (powder exhaust fan)——排粉风机PCF(pulverized coal feeder)——给粉机HPA (heat primary air )——热一次风CPA (cold primary air )——冷一次风SECA (secondary air)——二次风TA (tertiary air)——三次风SA (seal air)——密封风AR (air register)——风门OILP (oil pistol)——油枪IGNT (ignition) ——点火枪FULP (fuel pump)——燃油泵FLTK (flash tank)——扩容器FURN(furnace) ——煤粉炉炉膛2、流化床锅炉HPCB（high-pressure centrifugal blower）——高压流化风机CFBB（Circulating Fluidized-bed Boiler）——循环流化床炉膛CYCS（cyclone separator）——旋风分离器UBF(U-type back-feeder) ——U形返料器ASHC(ash cooler) ——冷渣器3、余热锅炉CVB(convection bank) ——对流管束SWS(steam/water separator) ——汽水分离器WJP（Water jet pump）——射水泵WH(water heater) ——热水器EVP(evaporator) ——蒸发器OEJ（oil ejector）——注油器OFT（oil filter）——滤油器OCL（oil cooler）——冷油器窑头余热锅炉AQCB(此处AQC指air quenching cooler，为篦冷机，不是窑头的意思，但行业习惯称窑头余热炉为AQC炉)窑尾余热锅炉SPB(此处SP指suspension preheater，为悬浮预热器，不是窑尾的意思，但行业习惯称窑尾余热炉为SP炉)（二）汽机部分HP (high pressure cylinder) ——高压缸IP (intermediate pressure cylinder) ——中压缸LP (low pressure cylinder) ——低压缸DEA (deaerator) ——除氧器COND (condenser) ——凝汽器HPH (high pressure heater) ——高压加热器LPH (low pressure heater) ——低压加热器SSH (shaft seal heater) ——轴封加热器MFP (motor-driven feed pump) ——电动给水泵SFP (steam feed pump) ——汽动给水泵V ACP (vacuum pump) ——真空泵CEP (Condensate extraction pump) ——凝结水泵DRNP (drain pump) ——疏水泵CIRP (circulating pump) ——循环泵LIFTP (lift pump) ——顶轴油泵LUBOP (lubricating oil pump) ——润滑油泵DCOP——直流润滑油泵ACOP——交流润滑油泵HPOP——高压启动油泵MAINOP——主油泵EHP——EH油泵OTANK (oil tank) ——油箱WTANK (water tank) ——水箱HEADER——联箱SSF (shaft seal fan) ——轴封风机IFF (induced-fume fan) ——排烟风机AIRCMP(air compressing engine) ——空气压缩机（三）DEH部分TV——高压缸主汽门GV——高压缸调节门RV——中压缸主汽门IV——中压缸调节门LV——低压缸调节门（四）电气部分GEN (generator) ——发电机XFORM (transformer) ——变压器BUS (bus bar) ——母线BRK (circuit breaker) ——断路器SWITCH (isolating switch) ——隔离开关EXCT (exciter) ——励磁机PEXCT (pilot exciter) ——副励磁机（五）系统分类feed water system ——给水系统water-steam system ——汽水系统desuperheater system ——减温水系统combustion system ——燃烧系统extraction steam system ——抽汽系统heat supply system ——热网系统lubricating oil system——润滑油系统fuel oil system——燃油系统soot blower system——吹灰系统ignition system——点火系统powder manufacturing system——制粉系统drain system——疏水系统wind-fume system——风烟系统blowdown system——排污系统condensate system——凝结水系统deaerator system——除氧器系统turbine body——汽轮机本体by-pass system——旁路系统cooling water system——冷却水系统circulation water system——循环水系统vacuum system——真空系统（六）阀门shutoff valve——截止阀check valve——单向阀motorized valve——电动阀magnetic valve——电磁阀pneumatic positioner valve——气动阀flapper valve——挡板阀steam converter valve——减温减压阀fast valve——快关阀blow down valve——吹扫阀blow down valve——排污阀（七）其它CCS(coordinated control system) ——协调控制系统SIS(supervision & information system) ——监控信息系统MIS(management information system) ——管理信息系统BF(MODE)(borler follow mode) ——锅炉跟随方式TF(MODE)(turbine follow mode) ——汽轮机跟随方式CCS(MODE)(coordinated control mode) ——协调控制方式Manual Mode——手动方式BASE MODE——基本（手动）方式ULD(unit load demand) ——机组负荷指令ADS(automatic dispatch system) ——自动调度系统UM(unit master) ——单元机组主控制器BM&TM(boiler master & turbine master) ——锅炉主控制器和汽轮机主控制器BCS(boiler control system) ——锅炉控制系统TCS(turbine control system) ——汽轮机控制系统RB(run back) ——负荷返回RD(run down) ——强迫降负荷（迫降负荷）RU(run up) ——强迫升负荷（迫升负荷）FCB(fast cut back) ——快速减负荷AGC(automatic generation control) ——自动发电控制MFT(master fuel trip) ——主燃料跳闸CP MODE(constan pressure mode) ——定压方式VP MODE(variable pressure mode) ——滑压方式MCR(maximum continuous rating) ——最大连续出力ECR(economic continuous rating)——经济连续出力B-MCR(boiler maximum continuous rating) ——锅炉最大连续出力T-MCR(turbine maximum continuous rating) ——汽轮机最大连续出力MCS(modulating control system) ——模拟量控制系统FSSS(furnace safeguard supervisory system) ——炉膛安全监控系统BMS(burner management system) ——燃烧器管理系统SCS(sequential control system) ——顺序控制系统ECS(electric control system) ——电气控制系统DEH(digital electric-hydraulic control system) ——数字电液控制系统OPC(over speed control) ——超速控制AST(autostop trip) ——自动停机遮断ETS(emergence trip systems) ——危急遮断系统ATC(automatic turbine control) ——自动汽轮机程序控制TSI(turbine supervisory instrumentation) ——汽轮机监视系统PLC(programmable logic controller) ——可编程逻辑控制器SCR（selective catalytic reduction）——选择性催化还原法二、电厂术语——锅炉部分1．临界压力锅炉supercritical pressure boiler2. 亚临界压力锅炉subcritical pressure boiler3. 超高压锅炉super-high pressure boiler4. 蒸汽锅炉steam boiler5. 蒸汽发生器steam generator6. 液态排渣锅炉wet bottom boiler7. 固态排渣锅炉dry bottom boiler8. 燃煤锅炉coal-fired boiler9. 燃气锅炉Gas-fired boiler10.燃油锅炉oil-fired boiler11.自然循环锅炉natural circulation boiler12.汽包（锅筒）锅炉drum boiler13.强制循环锅炉controlled circulation boiler14.直流锅炉once-through boiler15.复合循环锅炉combined circulation boiler16.旋风炉cyclone furnace boiler17.沸腾炉fluidized bed combustion(FBC)boiler18.循环硫化床circulating fluidized bed combustion(FBC)boiler19.增压循环硫化床锅炉pressurized circulating fluidized bed combustion(PCFBC) boiler20.链条锅炉chain-grate boiler21.热水锅炉hot-water boiler22.废热（余热）锅炉water-heat boiler, heat recover steam generator(HRSG)23.启动锅炉start-up boiler24.厂用锅炉auxiliary boiler25.垃圾焚烧锅炉refuse-fired boiler, refuse incinerator27.露天锅炉outdoor boiler28.单炉膛锅炉single furnace boiler29.双炉膛锅炉twin furnace boiler30.W火焰锅炉W-flame boiler, vertical-fired boiler31.L火焰锅炉L-shape furnace boiler32.塔式锅炉tower boiler33.箱式锅炉box-type boiler34．炉墙furnace wall35. 汽包（锅筒）drum36.封头head37.汽包封头drum end plate, drum head38.下降管downcomer39.集中下降管centralized downcomer40.分散下降管distributed downcomer41.上升管riser42.管束（排）tube bundle43.管屏tube platen44.省煤器管economizer tube45.过热器管superheated tube46.再热器管reheater tube47.蛇形管coil48.吊挂管supporting tube49.引入管inlet pipe50.引出管outlet pipe51.饱和蒸汽管saturated steam pipe52.水冷壁管water wall tube53.鳍片管finned tube, fin tube, gilled tube54.内螺纹管rifled tube, grooved tube55.吸潮管moisture absorption piping56.水冷壁water wall57.膜式水冷壁membrane wall58.内螺纹水冷壁rifled tube water wall59.联箱header60.集汽联箱steam header61.卫燃带bailey wall, refractory belt62包墙管（包覆管）wall enclosure tube63.防渣管（弗斯顿管）slag screen, feston tube64.锅炉本体boiler proper65.锅炉机组boiler unit66.锅炉构架boiler structure67.炉膛boiler framework68.燃烧器furnace69.直流式燃烧器direct-flow burner70.旋流式燃烧器turbulent burner71.低NOX燃烧器low NOX burner72.摇摆式燃烧器tilting burner73.缝隙式燃烧器split burner74.燃烧室combustion chamber75.油枪oil gun torch76.风门damper77.一次风primary air78.二次风secondary air79.三次风tertiary air80.煤粉管道pulverized coal piping81.管板tube plate82.沸点boiling temperature83.过热器superheater84.前屏过热器front platen superheater85.后屏过热器rear plate superheater86.对流过热器convection superheater87.辐射过热器radiant superheater88.屏式过热器plate superheater89.顶棚过热器ceiling superheater90.包墙过热器wall enclosure superheater91.前包墙过热器front wall enclosure superheater92.后包墙过热器rear wall enclosure superheater93.侧包墙过热器side wall enclosure superheater94.吹灰器soot blower95.转动式吹灰器rotary soot bolwer96.伸缩式吹灰器retractable soot blower97.受热面积heating surface area, heat absorption area98.炉膛容积furnace volume99.炉膛热负荷furnace heat release rate, furnace heating absorption rate 100.汽水分离器steam separator, moisture separator101.起动分离器starting separator102.再循环管recirculating piping103.暖风器steam air heater104.再热器reheater105.再热器冷段primary reheater106.再热器热段final reheater107.顶棚ceiling108.省煤器economizer109.管式省煤器tube economizer110.管式空气预热器tubular air preheater111.回转式（再生式）空气预热器regenerative air preheater, rotary air preheater112.板式空气预热器plate air preheater113.空气预热器air preheater114.三分仓空气预热器trisector regenerative air preheater115.漏风系数air leakage coefficient116.漏风率air leakage ratio117.漏风系统air leakage system118.漏风试验air leakage test119.安全门safety valve120.安全门开启压力opening pressure of safety valve121.安全门回座压力safety valve reseating pressure122.安全门压力整定试验pressure setting test of safety valve123.安全门动作压力safety valve operating pressure124.饱和蒸汽安全门saturated steam safety valve125. 过热蒸汽安全门superheated steam safety valve126.再热蒸汽安全门reheated steam safety valve127.防暴门explosion vent128.检查孔inspection hole129.事故喷水阀emergency water spray valve130.汽包事故放水阀emergency drum drain valve 131.三通阀three-way valve132.反冲洗阀back wash valve133.取样阀sampling valve134.插板gate135.给水大旁路门feedwater overall bypass valve 136.给水小旁路门feedwater individual bypass valve 137.大板梁plate girder, upper beam138.外护板outer casing139.锅炉排污blowdown140.定期排污扩容器intermittent blowdown flash tank 141.连续排污扩容器continuous blowdown flash tank 142.灰斗ash hopper143.冷灰斗bottom ash hopper, furnace hopper144.混合器mixer145.齿圈（大牙轮）ring gear, geared ring146.空调器air conditioner147.空气压缩机air compressor148.给煤机coal feeder149.皮带式给煤机belt coal feeder150.刮板式给煤机scraper coal feeder151.叶轮式给煤机paddle coal feeder152.给粉机pulverizer coal feeder153.磨煤机coal pulverizer, coal mill154.钢球磨煤机tube mill155.中速辊式磨煤机roller mill, bowl mill, disk roll mill 156.双进双出钢求磨煤机double inlet and outlet tube mill 157.中速磨煤机medium speed mill158.风扇磨煤机beater wheel mill, beater mill159.排粉风机pulverized coal exhauster160.一次风机primary air fan161. 烟气再循环风机gas recirculation fan162.送风机forced draft fan, force fan163.引风机induced draft fan, induced fan164.离心风机centrifugal fan165.轴流风机axial-flow fan166.双速风机double speed fan167.轴流静叶可调风机adjustable static-blade axial-flow fan fixed pitch axial-flow fan168.轴流动叶可调风机adjustable moving-blade axial-flow fan variable pitch axial-flow fan169.原煤斗raw coal bunker, raw coal silo170.煤粉仓pulverized coal bunker171.输粉机pulverized coal conveyer172.刮板输粉机scraper pulverized coal conveyer 173.螺旋输粉机pulverized coal screw conveyer174.粗粉分离器classifier175.细粉分离器（旋风分离器）cyclone separator 176.锁气器air lock, flap177.减速机speed reduce178.看火孔observation hole179.人孔门man hole180.重油泵heavy oil pump181.重油加热器heavy oil heater182.汽-汽热交换器biflux183.煤气罐gas tank184.膨胀补偿节expansion joint185.直吹式制粉系统direct firing pulverizing system 186.中贮式制粉系统bin storage type pulverizing system 187.锅炉效率boiler efficiency188.锅炉热力计算boiler thermodynamic calculation 189.锅炉空气动力计算boiler aerodynamic calculation 190.锅炉水循环计算boiler water circulation calculation 191.锅炉水力计算boiler hydrodynamic calculation 192.锅炉强度计算boiler strength calculation193.锅炉热平衡boiler heat balance calculation 194.正平衡法direct balance method195.反平衡法indirect balance method196.过剩空气系数excess air coefficient197.排烟温度flue gas temperature198.单位蒸量specific evaporation199.低温腐蚀low temperature corrosion200.高温腐蚀high temperature corrosion201.结渣lagging202.结垢腐蚀deposit corrosion203.飞灰磨损fly ash erosion204炉膛负压furnace draft205.最高允许温度maximum permissible temperature 206.炉膛正压furnace pressure207.水循环water circulation208.循环倍率circulation ratio209.除尘器dust collector, precipitator210.静电除尘器electrostatic precipitator211.整流装置rectifying device212.锤打装置rapping gear213.含尘浓度dust loading concentration214.煤灰细度dust fineness215.除尘效率dust collection efficiency216.干式除尘器dry dust collector217.湿式除尘器wet dust collector, scrubber218.文丘里除尘器venture scrubber219.布袋除尘器fabric filter, bag house220.钢珠除尘装置shot-cleaning device221.水膜式除尘器centrifugal scrubber222.灰渣泵ash pump, slag pump223.轴封泵shaft sealing pump224.灰浆泵ash slurry pump225.除尘水泵dedusting pump226.回收水池water recovery pond227.清水池clean water pond228.灰浆池ash slurry pond229.油泵坑oil pump pit230.灰库ash silo231.灰场ash yard232.灰坝ash yard dam233.耐火砖firebrick234.保温材料heat-insulating material235.干式除灰（气力除灰）pneumatic pressure ash handling 236.水力除灰hydraulic ash handling237.正压气力除灰pneumatic pressure ash handling 238.负压气力除灰pneumatic pressure ash handling 239.仓式泵fluidizing transporter240.空气斜槽airslide, air gravity conveyor241.灰渣分除bottom and fly ash separate handling 242.灰渣混除bottom and fly ash mixed handling 243.灰渣利用bottom and fly ash recovery244.排渣槽bottom ash hopper245.埋刮板捞渣机submerged slag conveyor246.螺旋式捞渣机screw slag conveyor247.碎渣机clinker grinder, slag crusher248.振动筛vibrating screen249.稳燃器flame stabiliaer250.燃烧器蜗壳burner spiral case251.雾化器atomization252.机械雾化mechanical atomization253.蒸汽雾化steam atomization254.空气雾化air atomization255.气固两相流动gas-solid two-phase flow256.闭路循环closed cycle257.蒸汽带水carryoery258.炉膛灭火boiler flame failure, boiler flame blackout259.稳定燃烧stable combustion260.压力容器pressure vessel261.支吊架supports and hangers262.原煤管道raw coal piping263.风道air duct264.热风道hot air duct265.冷风道cold air duct266.穿墙套管wall-through bushing, wall-bushing 267.伸缩节expansion joint268.送粉管道pulverized coal feed piping269.燃油管道fuel oil piping270.风管道air piping271.一次风管道primary air piping272.二次风管道secondary air piping273.落粉管pulverized coal chute274.除灰管道ash piping275.烟道gas dust, gas pass276.尾部烟道convection flue gas pass277.煤气管gas piping278.连续排污管continuous blowdown piping 279.烟囱chimney, stack280.多管式烟囱multi-flue chimney281.燃烧combustion282.四角喷射燃烧corner firing283.燃烧速度combustion rate284.机械未完全燃烧热损失heat loss due to mechanical incomplete combustion285化学未完全燃烧热损失heat loss due to chemical incomplete combustion286.灰渣热损失heat loss due to sensible heat in refuse287.排烟热损失heat loss due to flue gas288.散热损失heat loss due to radiation289.热损失heat loss290.火焰flame291.不稳定燃烧instable combustion292.负压燃烧balance draft combustion293.微负压燃烧pressurized combustion294.炉膛容积热负荷furnace volume heat release rate295.炉膛温度furnace temperature296.锅炉水循环boiler water circulation297.偏离泡核沸腾departure from nucleate boiling(DNB)298.水压试验hydraulic test299.汽水共沸priming300.点火ignition301.点火准备ignition preparation302.着火点firing point, ignition temperature303.折焰角nose304.飞灰fly ash305.煤粉细度fineness of pulverized coal306.灰ash307.灰的熔化点ash fushion temperature, ash fushion point, ash melting point308.可磨系数grindability index309.最大蒸发量maximum evaporation310.锅炉热平衡boiler heat balance311.超负荷运行overload operation312.正压positive pressure313.负压negative pressure314.理论空气量theoretical air quantity315.过剩空气量excess air quantity316.冷风cold air317.热风hot air318.除渣slag removal319.烟气flue gas320.锅炉上水boiler water filling321.蠕胀爆管tube burst due to creep322.汽包满水overfeed of water into drum323.锅炉灭火boiler fire extinction324.爆燃puff325.爆炸（外爆）explosion326.内爆implosion327.防爆anti-explosion328.煤粉自燃pulverized coal self-ignition, pulverized coal spontaneous combustion329.堵灰ash fouling330.堵煤coal jamming, coal plugging331.燃烧切圆firing tangential circle332.火焰中心flame center333.积粉pulverized coal deposits334.粉灰ash deposits335.飞灰可燃物combustibles in fly ash336.点火用油fuel oil for ignition337.飞灰腐蚀fly ash corrosion338.受热面heating surface339.辐射受热面radiation heating surface340.对流受热面convection heating surface341.尾部受热面rear heat recovery surface342.含氧量oxygen content343.蒸发量evaporation, evaporative capacity 344.切换风air switch-over345.煤耗率coal consumption rate346.入炉煤发热量heating value of the as fired coal 347.停炉boiler shutdown348.熄火fire-off349.灰水回收recovery of ash slurry water350.细灰fine ash351.粗灰coarse ash352.干灰dry ash353.湿灰wet ash354.燃烧系数combustion system, firing system 355.制粉系统coal pulverizing system356.除灰系统ash handling system三、电厂术语——汽轮机部分357.汽轮机steam turbine358.凝汽式汽轮机condensing steam turbine359.背压式汽轮机back pressure turbine360.抽汽式汽轮机steam extraction turbine361.中间再热式汽轮机reheating type steam turbine362.供热式汽轮机steam supply turbine, heat supply turbine, cogeneration turbine363.冲动式汽轮机impulse turbine364.反动式汽轮机reaction turbine365.轴流式汽轮机axial flow turbine366.辐流式汽轮机radial flow turbine367.单轴汽轮机tandem compound turbine, single-shaft turbine368.双轴汽轮机double-shaft turbine, cross compound turbine369.前置式汽轮机topping turbine370.燃气轮机gas turbine371.高压汽轮机high pressure turbine372.中压汽轮机medium pressure turbine373.低压汽轮机low pressure turbine374.超高压汽轮机ultra pressure turbine375.亚临界压力汽轮机subcritical pressure turbine376.超临界压力汽轮机supercritical pressure turbine377.空冷式汽轮机组air cooled turbine unit378.燃气轮机组（装置）gas turbine unit379.高压汽缸high-pressure(HP) cylinder380.中压汽缸intermediate-pressure(IP) cylinder381.低压汽缸low-pressure(LP) cylinder382.内汽缸inner casing383.外汽缸outer casing384.上汽缸upper casing385.下汽缸lower casing386.汽缸法兰螺栓加热装置cylinder flange heating appliance 387.汽缸台板（底板）cylinder sole pin388.汽缸猫爪cylinder claw389.滑销sliding pin390.横销traverse pin391.纵销longitudinal pin392.立销vertical pin393.定位销aligning pin, locating pin394.汽轮机转子turbine rotor395.叶轮blade disc396.叶片blade, bucket397.动叶片moving blade398.静叶片stationary blade399.叶根型式type of blade root400.末级叶片长度length of last stage blade 401.喷嘴室nozzle box402.末级叶片强度last stage blade stress403.排汽室steam exhaust hood404.喷嘴nozzle405.围带shroud ring406.拉筋（拉金）lacing wire407.平衡块balance weight408.固定螺钉dowel409.隔板diaphragm410.隔板套diaphragm sleeve411.隔板汽封diaphragm seal, diaphragm sealing 412.汽封steam seal gland, steam sealing413.迷宫式汽封labyrinth seal414.梳齿式汽封serrate-type steam seal415.汽封套seal bushing416.汽封块seal block417.汽封齿seal tooth418.轴承支架bearing stoll, bearing bracket 419.主轴承箱main bearing box420.滚珠轴承ball bearing421.滚柱轴承roller bearing422.滑动轴承sliding bearing423.推力轴承thrust bearing424.止推环thrust collar425.瓦枕bearing pillow426.锁饼lock427.推力瓦块thrust bearing pad428.主油泵main oil pump429.备用油泵emergency bearing oil pump430.调速油泵regulation oil pump, speed governing oil pump 431.交流润滑油泵AC lube oil pump432.直流润滑油泵DC lube oil pump433.注油器oil injector434.同步器synchronizer435.同步器手轮synchronizer hand wheel436.控制滑阀pilot valve437.随动滑阀servo-valve438.分配滑阀distributing pilot valve, distributor valve 439.中间滑阀intermediate valve440.微分器differentiator441.功率限制器load limiter442.动态校正器dynamic corrector443.滑阀套valve sleeve444.喷油嘴oil nozzle445.弹性调速器flexible governor446.调速器挡块governor stop447.危急遮断器滑阀emergency trip pilot valve448.撞击子ram449.防火滑阀fire protection pilot valve450.延滞滑阀delay pilot valve451.跟踪滑阀follow-up pilot valve452.电-液转换器electro-hydraulic converter, electro-hydraulic transducer453.切换滑阀change-over pilot valve454.危急保安器emergency governor455.危急保安器滑阀emergency governor pilot valve456.超速试验滑阀overspeed test pilot valve457.喷油试验滑阀nozzle test pilot valve458.反馈滑阀feedback pilot valve459.起动排油阀oil drain valve at star-up460.紧急放油阀emergency oil relieve valve461.排油口oil diacharge outlet462.节流滑阀throttle pilot valve463.滑动油阀movable pilot valve464.高压自动关闭器high-pressure automatic closing gear465.中压自动关闭器medium pressure automatic closing gear466.高压油动机（高压伺服马达）high-pressure hydraulic actuator, high-pressure servo-motor467.中压油动机medium-pressure hydraulic actuator, medium-pressure servo-motor468.杠杆lever469.轴shaft470.主轴main shaft471.传动轴(主动轴) driven shaft472.被动轴（从动轴）driven shaft473.小轴axle474.联轴器coupling475.刚性联轴器rigid coupling476.半挠性联轴器semi-flexible coupling477.齿型联轴器serrated coupling478.冷油器oil cooler479.溢油器oil overflow valve480.排油烟机oil-fume extractor, oil fume exhaust481.油烟分离器oil-fume separator482.油净化器oil purifier, oil conditioner483.过滤罐filtering tank484.布袋式过滤器bag filter, fabric filter485.齿轮油泵gear oil pump486.顶轴油泵jacking oil pump487.柱塞式油泵piston type oil pump488.螺杆式油泵worm type oil pump489.盘车装置turning gear490.盘车手轮turning gear hand wheel491.化桩板lagging enclosure492.齿轮gear493.直齿式齿轮spur gear494.斜齿式齿轮helical gear495.伞型齿轮bevel gear496.蜗轮worm wheel497.蜗杆worm stem498.弹簧spring499.密封油箱sealing oil tank500.空气侧交流密封油泵air side AC sealing oil pump 501.空气侧支流密封油泵air side DC sealing oil pump 502.压差阀differential pressure valve503.平衡阀balancing valve504.密封瓦sealing pad505.缓冲油箱buffer oil tank506.高位油箱head oil tank, elevated oil tank507.事故油箱emergency oil tank508.磁性过滤器magnetic filter509.发电机内冷水箱generator inner cooling water tank 510.发电机内冷水泵generator inner cooling water pump 511.离子交换器ion exchanger512.干燥器dryer, drier513.冷凝式干燥器condensing type drier514.凝汽器condenser515.多压式凝汽器multi-pressure condenser516.单流程凝汽器single-pass condenser517.双流程凝汽器double-pass condenser518.黄铜管brass tube519.管板tube plate520.凝汽器喉部condenser throat521.热水井hot well522.凝结水泵condensate pump523.泵壳pump casing524.盘根gland packing525.盘根压盖gland top cover526.盘根端盖gland end cover527.填料packing528.轴封抽汽风机shaft seal extraction fan529.轴封抽汽冷却器shaft seal extraction cooler, gland cooler 530.轴封漏汽加热器shaft seal leakage heater531.低压加热器low-pressure feed water heater532.中压加热器media-pressure feed water heater533.高压加热器high-pressure feed water heater534.蒸汽冷却器steam cooler535.疏水冷却器drain water cooler536.汽侧steam side537.水侧water side538.U型管U-tube539.除氧器deaerator540.储水池water storage pond541.卧式除氧器horizontal type deaerator542.立式除氧器vertical type deaerator543.喷雾式除氧器atomizing type deaerator544.淋水盘water spraying tray, sprinkling tray545.除氧水箱deaerated water tank546.稳压水箱surge water tank, stabilizing water tank547.除盐水箱demineralized water tank548.除盐水泵demineralized water pump549.汽动给水泵steam-driven feed water pump550.电动调速给水泵motor-driven variable speed feed water pump 551.前置水泵booster pump552.给水泵feed water pump553.机械密封mechanical seal554.碳精密封环carbon seal ring, carbon packing ring555.动环moving ring556.静环static ring557.平衡盘balancing disc558.液力偶合器hydraulic coupler559.泵轮（主动轮）pump impeller, driving impeller560.涡轮（从动轮）whirling impeller, driven impeller561.勺管scoop tube562.辅助油泵auxiliary oil pump563.疏水泵drain pump564.疏水扩容器drain flash tank565.疏水箱drain tank566.热网加热器heater for heating network, heating network hot water heater567.生水加热器raw water heater568.热网水泵pump for heating network, heating network hot water pump569.生水泵raw water pump570.除尘水泵pump for scrubber, scrubber water pump 571.壳体case, shell572.水室water chamber573.封头end cover574.挡板baffle plate575.导流板guide plate576.射水泵water jet pump577.真空泵vaccum pump578.射水抽气器water jet air ejector579.射汽抽气器steam jet air ejector580.射水池water jet pond581.排水池drain water pond582.工业水泵industrial water pump, service water pump 583.排污泵blowdown pump584.轴流泵axial flow pump585.清水泵clean water pump586.污水泵sewage pump587.排水泵water discharge pump588.立式深井泵vertical deep-well pump589.深井泵deep-well pump590.潜水泵submerged pump591.循环水泵circulating water pump592.清污机trash remover593.混流泵mixed flow pump594.离心泵centrifugal pump595.旋转滤网rotating type screen, screw type strainer 596.胶球泵rubber ball recirculating pump597.收球网ball screen598.装球网ball collector599.管式冷却器tubular cooler, tube type cooler599/1.支撑斜钢supporting wedge600.板式冷却器plate type cooler601.冷却水池cooling water pond602.喷水池spraying water pond603.冷却水塔cooling tower604.自然通风冷却塔natural draft cooling tower 605.逆流式冷却塔reverse flow cooling tower 606.横流式塔transverse flow cooling tower607.机力通风冷却塔mechanical draft cooling tower 608.空气冷却塔air cooling tower609.干式冷却塔dry cooling tower610.分水槽water diversion channel611.竖井shaft, well612.闸板井gate well613.闸门室gate chamber, gate house614.挡风板air baffle plate615.新（主）蒸汽管道main steam piping, live steam piping 616.主蒸汽系统main steam system617.再热蒸汽系统reheat steam syetem618.抽汽系统extraction steam system619.轴封供汽系统shaft seal steam supply system620.轴封shaft seal621.门杆漏汽系统valve lever leakage steam system622.汽缸法兰螺栓加热系统casing flange and bolt heating system 623.真空系统vaccum system624.凝结水系统condensate system625.再热蒸汽管道reheat steam system626.给水系统feed water system627.循环水系统circulating water system628.工业水系统industrial water system, service water system 629.供油系统oil supply system630.密封油系统seal oil system631.厂用蒸汽系统auxiliary steam system632.调速系统speed governing system633.电液调速系统electro-hydraulic speed governing system634.发电机内冷水系统generator inner cooling water system 635.热网系统heating network system636.导汽管steam lead pipe637.连通管inter-connecting pipe638.抽汽管道steam extraction pipe639.抽汽母管steam extraction header640.厂用蒸汽管道plant service steam piping641.厂用蒸汽母管plant service steam header642.蒸汽旁路系统steam bypass system643.蒸汽大旁路single stage steam bypass644.一级蒸汽旁路first stage steam bypass645.二级蒸汽旁路second stage steam bypass646.辅助蒸汽母管auxiliary steam header647.供汽联箱steam header648.回汽联箱return steam header649.供水联箱water supply header650.回水联箱return water header651.门杆漏汽管道valve lever steam leakage piping652.轴封漏汽管道shaft seal leakage steam piping653.抽空气管道air extraction piping654.压缩空气管道compressed air piping655.氢气管道hydrogen piping656.疏水管道drain water piping657.凝结水管道condensate piping658.循环水管道circulating water piping659.工业水管道industrial water piping, service water piping 660.冷却水管道cooling water piping661.给水管道feed water piping662.除盐水管道demineralized water piping663.减温水管道attemperating water piping664.再循环水管道recirculating water piping665.排水管道water discharge piping666.润滑油供油管道lube oil supply piping667.润滑油管lube oil piping668.调速油管governing oil piping669.回油管道return oil piping670.压力油管道pressure oil piping671.密封油管道seal oil piping672.脉动油管pulsating oil piping673.热网水管道heating network water piping674.平衡管balance pipe675.电动主闸门motor-operated main gate valve676.高压主汽门high-pressure main stop valve677.中压主汽门intermediate pressure main stop valve678.旁路门bypass valve679.防腐汽门corrosion-proof valve680.高压调速汽门high-pressure governor valve 681.中压调速汽门medium pressure governor valve 682.对空排汽门atmospheric relief valve683.疏水门drain valve684.调整门adjusting valve685.电动门motor-operated valve686.手动门hand-operated valve687.减温器attemperator, desuperheater688.减压器（阀）pressure reducer(valve)689.减温减压器temperature and pressure reducer 690.抽汽电动门motor-operated steam extraction valve 691.抽汽逆止门extraction check valve692.高压排汽逆止门high-pressure exhaust check valve 693.逆止门check valve, non-return valve694.入口门inlet valve695.出口门outlet valve696.球型阀globe valve697.闸板阀gate valve698.针型阀needle valve699.翻板阀tripper valve。