各种制式螺纹攻牙钻孔径和滚造径对照表，太全了金属加工2015-10-17 关注作者原文地址本表所推选钻头孔径，是针对攻牙加工时，能够很容易的了解钻头直径；而依据市售之标准钻头所选定的。
在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸，精度有很大影响，所以使用本表之钻孔径，若有不当之处，应实际状况适当的变更钻头直径，本表依据2级牙制订。
公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.670 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M20×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376 M22×1.0 21.00 21.153 20.917 M24×2.0 22.00 22.210 21.835 M24×1.5 22.50 22.676 22.376 M24×1.0 23.00 23.153 22.917 M25×2.0 23.00 23.210 22.835 M25×1.5 23.50 23.676 23.376 M25×1.0 24.00 24.153 23.917 M26×1.5 24.50 24.676 24.376 M27×2.0 25.00 25.210 24.835 M27×1.5 25.50 25.676 25.376 M27×1.0 26.00 26.153 25.917 M28×2.0 26.00 26.210 25.835 M28×1.5 26.50 26.676 26.376 M28×1.0 27.00 27.153 26.917 M30×3.0 27.00 27.252 26.752 M30×2.0 28.00 28.210 27.835 M30×1.5 28.50 28.676 28.376 M30×1.0 29.00 29.153 28.917 M32×2.0 30.00 30.210 29.835 M32×1.5 30.50 30.676 30.376 M33×3.0 30.00 30.252 29.752 M33×2.0 31.00 31.210 30.835 M33×1.5 31.50 31.376 31.376 M35×1.5 33.50 33.676 33.376 M36×3.0 33.00 33.252 32.752 M36×2.0 34.00 34.210 33.835 M36×1.5 34.50 34.676 34.376 美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642NO.8-32(4.166) 3.40 3.530 3.302NO.10-24(4.826) 3.90 3.962 3.682NO.12-24(5.846) 4.50 4.597 4.3441/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3071 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339 PT1-1/2 -11 43.40 44 43.869 44.232 Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82公制螺纹规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425 美制粗螺纹规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76本表所推选钻头孔径,是针对攻牙加工时,能够很容易的了解钻头直径;而依据市售之标准钻头所选定的.在使用钻头的情况下,由于钻头的形状及尺寸,精度,被钻孔之材质等,对于所钻孔的尺寸,精度有很大影响,所以使用本表之钻孔径,若有不当之处,应实际状况适当的变更钻头直径,本表依据2级牙制订.公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106 M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.670 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M20×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.376 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826) 3.90 3.962 3.682 NO.12-24(5.846) 4.50 4.597 4.344 1/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3077/8 -9 19.50 19.761 19.1771 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/8 -28 8.10 8.2 8.249 8.388PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339PT1-1/2 -11 43.40 44 43.869 44.232Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76来源：直观学机械推荐阅读1.钢价惨烈下跌风暴即将来临?不要以为和你没关系2.世界名刀大全，简直太漂亮了免责声明：本文系网络转载，版权归原作者所有。
最大最小最大最小最大最小规格精度最大最小最大最小最大最小最大最小规格精度最大最小M1.0×0.20.800.8210.783M1.0×0.250.750.7850.729(螺丝牙外径）硬材软材M1.1×0.20.900.9210.883M1.1×0.250.850.8850.829No.0-80(1.524) 1.25 1.305 1.182 # 1 -64G5 1.76 1.68 2.65 2.6M1.2×0.2 1.00 1.0210.983M1.2×0.250.950.9850.929No.1-72(1.854) 1.55 1.612 1.474 #2 -56G4 2.04 1.96 3.25 3.2M1.4×0.2 1.20 1.221 1.183M1.4×0.3 1.10 1.142 1.075No.2-64(2.184) 1.85 1.912 1.756 # 3-48G4 2.35 2.25 3.75 3.7M1.6×0.2 1.40 1.421 1.383M1.6×0.35 1.25 1.321 1.221No.3-56(2.515) 2.1 2.197 2.025 #4 -40G5 2.64 2.54 5.15M1.7×0.2 1.50 1.521 1.483M1.7×0.35 1.35 1.421 1.321No.4-48(2.845) 2.4 2.458 2.271 #5 -40G5 2.97 2.87 6.6 6.5M1.8×0.2 1.60 1.621 1.583M1.8×0.35 1.45 1.521 1.421No.5-44(3.175) 2.7 2.74 2.551 #6 -32G53.22 3.1187.9M2.0×0.25 1.75 1.785 1.729M2.0×0.4 1.60 1.679 1.576No.6-40(3.505) 2.9 3.022 2.82 #8 -32G63.89 3.789.49.3M2.2×0.25 1.95 1.985 1.929M2.2×0.45 1.75 1.838 1.713No.8-36(4.166) 3.5 3.606 3.404 #10 -24G6 4.44 4.310.710.5M2.3×0.25 2.05 2.085 2.029M2.3×0.4 1.90 1.979 1.867No.10-32(4.826) 4.1 4.165 3.963 #12 -24G65.07 4.9612.312M2.5×0.35 2.20 2.221 2.121M2.5×0.45 2.10 2.138 2.013No.12-28(5.846)4.6 4.724 4.496 1/4" -20G75.86 5.7313.713.5M2.6×0.35 2.20 2.321 2.221M2.6×0.45 2.20 2.238 2.1132001/4/28 5.5 5.588 5.36 5/16" -18G77.387.2316.716.5M3.0×0.35 2.70 2.721 2.621M3.0×0.5 2.50 2.599 2.4595/16 -24 6.97.035 6.782 3/8" -16G78.898.7219.519.3M3.5×0.35 3.20 3.221 3.121M3.5×0.6 2.90 3.010 2.8502003/8/248.58.6368.382 7/16" -14G810.410.0222.422M4.0×0.5 3.50 3.599 3.459M4.0×0.7 3.30 3.422 3.2427/16 -209.910.0339.729 1/2" -13G811.9211.72524.8M4.5×0.5 4.00 4.099 3.959M4.5×0.75 3.80 3.878 3.6881/2-2011.511.60711.32928.328M5.0×0.5 4.50 4.599 4.459M5.0×0.8 4.20 4.334 4.1349/16 -1812.913.08112.751 0 -80G5 1.45 1.39M5.5×0.5 5.00 5.099 4.959M6.0×1.0 5.00 5.153 4.9175/8一1814.514.68114.351 1 -72G5 1.7711.7M6.0×0.75 5.30 5.378 5.188M7.0×1.0 6.00 6.153 5.9173/4一1617.517.67817.3232 -64G4 2.06 1.98M6.0×0.5 5.50 5.599 5.459M8.0×1.25 6.80 6.912 6.6477/8一1420.520.67520.27 3 -56G4 2.37 2.29M7.0×0.75 6.30 6.378 6.188M9.0×1.257.807.9127.6471一1223.223.57123.114 4 -48G5 2.68 2.59M7.0×0.5 6.50 6.599 6.459M10×1.58.508.6768.3761-1/8-1226.526.74626.289 5 -44G5 2.99 2.9标准径钻孔径M8.0×1.07.007.153 6.917M11×1.59.509.6769.3761-1/4-1229.529.92129.464 6 -40G5 3.29 3.19最大最小M8.0×0.757.307.3787.188M12×1.7510.3010.44110.1061-3/8-1232.833.09632.639 8 -36G5 3.91 3.81M8.0×0.57.507.5997.459M14×2.012.0012.21011.8351-1/2-123636.27135.81410 -32G6 4.53 4.44 6.5 6.632 6.49M9.0×1.08.008.1537.917M16×2.014.0014.21013.835 12 -28G65.135.038.58.6378.495 M9.0×0.758.308.3788.188M18×2.515.5015.74415.294 1/4" -28G765.9111.411.54911.341M10×1.258.808.9128.647M20×2.517.5017.74417.294 5/16" -24G77.537.421515.05414.846M10×1.09.009.1538.917M22×2.519.5019.74419.294最大最小 3/8" -24G79.18.9918.518.77318.489M10×0.759.309.3789.188M24×3.021.0021.25220.752No.12-32 4.7 4.826 4.623 7/16" -20G810.6210.482424.25923.975M10×0.59.509.5999.459M27×3.024.0024.25223.7521/4 -32 5.6 5.69 5.486 1/2" -20G812.212.0630.230.47130.111M11×1.010.0010.1539.917M30×3.526.5026.77126.2115/16 -327.17.2647.08738.839.13238.772M11×0.7510.3010.37810.188M33×3.529.5029.77129.2113/8 -328.78.8658.66144.845.02544.665M12×1.510.5010.67610.376M36×4.032.0032.27031.6707/16 -2810.210.33810.13556.556.83656.476M12×1.2510.8010.91210.647M39×4.035.0035.27034.6701/2一2811.811.93811.709M12×1.011.0011.15310.9179/16 -2413.213.38613.132规格精度最大最小M12×0.511.5011.59911.4595/8一2414.814.98614.732M1.0×0.25G40.920.89M14×1.512.5012.67612.3763/7一2017.817.95817.678M1.2×0.25G4 1.12 1.09标准径M14×1.013.0013.15312.917最大最小7/8一502121.13320.853M1.4×0.30G4 1.3 1.26M15×1.513.5013.67613.376(螺丝牙外径）1一202424.30824.028M1.6×0.35G4 1.47 1.42M15×1.014.0014.15313.917No.1 -64(1.854) 1.55 1.582 1.425M1.7×0.35G4 1.57 1.52PT 1/16 - 28 6.1 6.2 6.244 6.384M16×1.514.5014.67614.376No.2 -56(2.184) 1.8 1.871 1.695M1.8×0.35G4 1.67 1.62PT 1/8 - 288.18.28.2498.388M16×1.015.0015.15314.917No.3 -48(2.515) 2.1 2.146 1.941M2.0×0.40G4 1.84 1.79PT 1/4 - 1910.71110.96211.174M17×1.515.5015.67615.376No.4 -40(2.845) 2.3 2.385 2.157M2.2×0.45G5 2.04 1.97PT 3/8 - 1914.214.514.44814.658M17×1.016.0016.15315.917No.5 -40(3.175) 2.6 2.697 2.487规格标准径最大最小M2.3×0.40G4 2.14 2.09PT 1/2 - 1417.61817.97918.263M18×2.016.0016.21015.835No.6 -32(3.505) 2.8 2.895 2.642SM1/16 - 80 1.25 1.281 1.211M2.5×0.45G5 2.34 2.27PT 3/4 - 142323.523.37823.663M18×1.516.5016.67616.376No.8 -32(4.166) 3.4 3.53 3.302SM5/64 - 64 1.55 1.593 1.513M2.6×0.45G5 2.44 2.37PT 1- 112929.529.45929.822M18×1.017.0017.15316.917No.10-24(4.826) 3.9 3.962 3.683SM3/32 - 56 1.90 1.936 1.841M3.0×0.50G5 2.82 2.75PT 1-1/4 - 1137.53837.97638.339M20×2.018.0018.21017.835No.12-24(5.486) 4.5 4.597 4.344SM3/32 -100 2.10 2.156 2.081M3.5×0.60G5 3.27 3.19PT 1-1/2 - 1143.44443.86944.232M20×1.518.5018.67618.3761/4 --20(6.35) 5.1 5.257 4.979SM1/8 - 32 2.30 2.393 2.233M4.0×0.70G6 3.72 3.65PT 2 - 1154.955.555.41255.844M20×1.019.0019.15318.9175/16 -18(7.93) 6.6 6.731 6.401SM1/8 - 40 2.50 2.551 2.421M5.0×0.80G6 4.67 4.59M22×2.020.0020.21019.8353/8—16(9.52)88.1537.798SM1/8 - 44 2.50 2.605 2.485M6.0×1.0G7 5.59 5.49M22×1.520.5020.67620.3767/16—14(11.11)9.49.559.144SM1/8 - 48 2.60 2.657 2.547M7.0×1.0G7 6.59 6.49M22×1.021.0021.15320.9171/2—13(12.7)10.811.02310.592SM9/64 - 32 2.70 2.79 2.630M8.0×1.25G77.497.36M24×2.022.0022.21021.8359/16—12(14.28)12.212.44611.989SM9/64 - 40 2.90 2.948 2.818M10×1.50G79.349.22M24×1.522.5022.67622.3765/8—11(15.87)13.612.86813.386 SM11/64 -32 3.50 3.584 3.424M10×1.25G79.499.35M24×1.023.0023.15322.9173/4—10(19.05)16.518.8416.307 SM11/64 -40 3.70 3.742 3.612M12×1.75G811.2311.09 6.7 6.843 6.561M25×2.023.0023.21022.8357/8—9(22.22)19.519.76119.177SM3/16 - 24 3.60 3.658 3.498M12×1.25G911.511.368.78.8488.566M25×1.523.5023.67623.3761—8(25.4)22.222.60621.971SM3/16 - 28 3.80 3.844 3.68411.711.8911.445M25×1.024.0024.15323.9171-1/8-7(28.57)2525.34924.638SM3/16 - 32 3.90 3.98 3.82015.215.39514.95M26×1.524.5024.67624.3761-1/4-728.228.52427.813SM3/16 - 40 4.05 4.138 4.0081919.17218.631M27×2.025.0025.21024.8351-3/8-630.831.11530.353SM7/32 - 32 4.70 4.774 4.6142121.12850.587M27×1.525.5025.67625.3761-1/2-63434.2933.528SM15/64 -28 5.00 5.055 4.87524.524.65824.117M27×1.026.0026.15325.9171-3/4-539.539.82738.964SM1/4 - 24 5.20 5.266 5.08628.228.41827.877M28×2.026.0026.21025.835 2 -4-1/245.245.59344.679SM1/4 - 28 5.40 5.452 5.27230.630.93130.291M28×1.526.5026.67626.376SM1/4 - 40 5.60 5.726 5.59635.235.59238.952M28×1.027.0027.15326.917SM9/32 - 20 5.70 5.824 5.63439.229.59238.952M30×3.027.0027.25226.752SM9/32 - 286.20 6.256 6.0664545.48544.845M30×2.028.0028.21027.835最大最小SM5/16 - 18 6.30 6.444 6.2545151.42850.788M30×1.528.5028.67628.376No.12-32 4.7 4.826 4.623SM5/16 - 24 6.80 6.864 6.674使用绞刀时不用绞刀时5757.29656.656M30×1.029.0029.15328.9171/4 -32 5.6 5.69 5.486SM5/16 - 28 6.907.05 6.8601/16 -27 6.1 6.25 6.35M32×2.030.0030.21029.8355/16 -327.17.2647.087SM11/32 -287.707.8437.6531/8一278.338.438.74M32×1.530.5030.67630.3763/8 -328.78.8658.661SM3/8 - 187.908.0537.8431/4一1810.7211.1311.13英 制 电 器 螺 纹W1 -8W1-1/8 -7W1-1/4 -7螺丝攻牙钻孔径对照表本表依据2级牙制定，由于钻头的形状，精度及被加工材质等对钻孔尺寸精度有很大影响，若有不当之处，应视实际状况适当变更钻头直径PF 2-11钻孔径规格W1/8 -40W5/32 -32W3/16 -24W1/4 -20W5/16 -18W3/8 -16W7/16 -14W1/2 -12W9/16 -12W5/8 -11W3/4 -10W7/8 -9PF 1-11PF 11/8-11PF 11/2-11PF 13/4-11PF 3/8-19PF 1/2-14PF 5/8-14PF 3//4-14PF 7/8-14标准径PF 规格新规格G PF 1/16 - 28PF 1/8-28PF 1/4-19英制螺纹不用绞刀时有交牙部之长度（最小）中之毋螺牙内径公制细螺纹美制粗牙螺纹规格（UNC)规格标准径2级牙钻孔径公制粗螺纹标准径2级牙钻孔径美制特细牙螺纹UNF PS 1/2 - 14PS 3/4 -14PS 1 - 11PS 1-1/4 - 11PS 1-1/2 - 11PS 规格新规格Rp PS 1/16 - 28PS 1/8 - 28PS 1/4 - 19规格（UNFF)规格标准径2级牙钻孔径公制迫牙丝攻钻孔径美制迫牙丝攻钻孔径标准径2级牙钻孔径N P TN P S2级牙钻孔径标准径规格（UNF)规格标准径美制管螺纹钻孔径最大最小针车用螺纹美制特粗螺纹UNC美制细牙螺纹规格 （UNF)标准径2级牙钻孔径PT 规格新规格Rc标准长度（最小）中之毋螺牙内径使用绞刀时PS 2 - 11PS 3/8 - 19PF 11/4-11英制管螺纹滚造径4.0-4.2规格2BA 3BA3.0-3.22.7-2.82.4-2.54BA 5BA 6BA。
