最新螺丝攻牙钻孔径对照表

螺丝攻牙钻孔径和滚丝径对照表公制粗螺纹美制粗螺纹规格标准径 2级牙钻孔径规格〔UNC〕标准径 2级牙钻孔径最大最小最大最小M1.0×0.25 0.75 0.785 0.729 NO.1-64(1.854) 1.55 1.582 1.425 M1.1×0.25 0.85 0.885 0.829 NO.2-56(2.184) 1.80 1.871 1.695 M1.2×0.25 0.95 0.9850.985 NO.3-48(2.515) 2.10 2.146 1.941M1.4×0.3 1.10 1.142 1.075 NO.4-40(2.845) 2.30 2.385 2.157 M1.6×0.35 1.25 1.321 1.221 NO.5-40(3.175) 2.60 2.697 2.487 M1.7×0.35 1.35 1.421 1.321 NO.6-32(3.505) 2.80 2.895 2.642 M1.8×0.35 1.45 1.521 1.421 NO8-32(4.166) 3.40 3.53 3.302M2.0×0.4 1.60 1.679 1.567 NO.10-24(4.826) 3.90 3.962 3.683 M2.2×0.45 1.75 1.838 1.713 NO.12-24(5.486) 4.50 4.597 4.344 M2.3×0.4 1.90 1.979 1.867 1/4-20 5.10 5.257 4.979M2.5×0.45 2.10 2.138 2.013 5/16-18 6.60 6.731 6.401M2.6×0.45 2.20 2.238 2.113 3/8-16 8.00 8.153 7.798M3.0×0.5 2.50 2.599 2.459 7/16-14 9.40 9.55 9.144M3.0×0.6 2.40 2.440 2.280 1/2-13 10.80 11.023 10.592M3.5×0.6 2.90 3.010 2.850 9/16-12 12.20 12.446 11.989M4.0×0.7 3.30 3.422 3.242 5/8-11 13.60 12.868 13.386M4.0×0.75 3.25 3.326 3.106 3/4-10 16.50 18.840 16.307M4.5×0.75 3.80 3.878 3.688 7/8-9 19.50 19.761 19.177M5.0×0.8 4.20 4.334 4.134 1 22.20 22.606 21.971M5.0×0.9 4.10 4.170 3.930 1-1/8-7 25.00 25.349 24.638M6.0×1.0 5.00 5.153 4.917 1-1/4-7 28.20 28.524 27.813M7.0×1.0 6.00 6.153 5.917 1-3/8-6 30.80 31.115 30.353M8.0×1.25 6.80 6.912 6.647 1-1/2-6 34.00 34.290 33.528M9.0×1.25 7.80 7.912 7.647 1-3/4-5 39.50 39.827 38.964M10×1.5 8.50 8.676 8.376 2-4-1/2 45.20 45.593 44.679M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.835M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 20.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211螺丝攻牙钻孔径和滚丝径对照表公制细螺纹美制细螺纹规格标准径 2级牙钻孔径规格〔UNC〕标准径 2级牙钻孔径最大最小最大最小M1.0×0.2 0.80 0.821 0.783 NO.0-80(1.524) 1.25 1.305 1.182M1.1×0.2 0.90 0.921 0.883 NO.1-72(1.854) 1.55 1.612 1.474M1.2×0.2 1.00 1.021 0.983 NO.2-64(2.184) 1.85 1.912 1.756M1.4×0.2 1.20 1.221 1.183 NO.3-56(2.515) 2.10 2.197 2.025M1.6×0.2 1.40 1.421 1.383 NO.4-48(2.845) 2.40 2.458 2.271M1.7×0.2 1.45 1.500 1.460 NO.5-44(3.175) 2.70 2.740 2.551M1.8×0.2 1.60 1.621 1.583 NO.6-40(3.505) 2.90 3.022 2.820 M2.0×0.25 1.75 1.785 1.729 NO.8-36(4.166) 3.50 3.606 3.404 M2.2×0.25 1.95 1.985 1.929 NO.10-32(4.826) 4.10 4.165 3.963 M2.3×0.25 2.05 2.061 2.001 NO.12-28(5.846) 4.60 4.724 4.496 M2.5×0.35 2.20 2.221 2.121 1/4-28 5.50 5.588 5.360M2.6×0.35 2.20 2.246 2.186 5/16-24 6.90 7.035 6.782M3.0×0.35 2.70 2.721 2.621 3/8-24 8.50 8.636 8.382M3.5×0.35 3.20 3.221 3.121 7/16-20 9.90 10.033 9.729M4.0×0.5 3.50 3.599 3.459 1/2-20 11.50 11.607 11.329M4.5×0.5 4.00 4.099 3.959 9/16-18 12.90 13.081 12.751M5.0×0.5 4.50 4.599 4.459 5/8-18 14.50 14.681 14.351M5.5×0.5 5.00 5.099 4.959 3/4-16 17.50 17.678 17.323M6.0×0.75 5.30 5.378 5.188 7/8-14 20.50 20.675 20.270M6.0×0.5 5.50 5.550 5.400 1-12 23.20 23.571 23.114M7.0×0.75 6.30 6.378 6.188 1-1/8-12 26.50 26.746 26.289M7.0×0.5 6.50 6.550 6.400 1-1/4-12 29.50 29.921 29.464M8.0×1.0 7.00 7.153 6.917 1-3/8-12 32.80 33.096 32.639M8.0×0.75 7.30 7.378 7.188 1-1/2-12 36.00 36.271 35.814M8.0×0.5 7.50 7.520 7.400M9.0×1.0 8.00 8.153 7.917M9.0×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188. .M12×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.400M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.676 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M22×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M30×1.0 29.00 29.153 28.917. v .M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.676 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376螺丝攻牙钻孔径和滚丝径对照表公制挤压丝攻钻孔径美制挤压丝攻钻孔径规格精度等级规格〔UNC〕精度等级G4-G6 G7-G8 G9 G4-G6 G7-G8 G9M1.0×0.25 0.86 0.88 － NO.2-56UNC 1.94 －－M1.1×0.25 0.96 0.98 － NO.3-48 2.23 －－M1.2×0.25 1.06 1.08 － NO.4-40 2.50 －－M1.4×0.3 1.24 1.25 － NO.5-40 2.83 －－M1.6×0.35 1.41 1.43 － NO.6-32 3.07 －－M1.7×0.35 1.51 1.53 － NO.8-32 3.73 3.77 －M1.8×0.35 1.61 1.63 － NO.10-24 4.24 4.3 －M2.0×0.4 1.78 1.80 － NO.12-24 4.90 4.96 －M2.2×0.45 1.95 1.98 － 1/4-20 － 5.72 －M2.3×0.4 2.08 2.10 － 5/16-18 － 7.24 －M2.5×0.45 2.25 2.28 － 3/8-16 － 8.74 8.81M2.6×0.45 2.35 2.38 － 7/16-14 － 10.20 10.30 M3.0×0.5 2.73 2.75 － 1/2-13 － 11.27 11.82M3.5×0.6 3.17 3.20 － NO.2-64UNF 1.97 －－M4.0×0.7 3.62 3.65 3.69 NO.3-56 2.27 －－M5.0×0.8 4.56 4.60 4.64 NO.4-48 2.56 －－M6.0×1.0 5.45 5.50 5.55 NO.5-44 2.86 －－M7.0×1.0 6.45 6.50 6.55 NO.6-40 3.16 －－M8.0×1.25 7.31 7.38 7.44 NO.8-36 3.78 －－M10×1.5 9.18 9.25 9.32 NO.10-32 4.39 4.43 －M10×1.25 9.31 9.38 9.44 NO.12-28 4.99 5.04 －M12×1.75 11.04 11.12 11.21 1/4-28 5.85 5.90 －M12×1.25 11.31 11.38 11.44 5/16-24 7.36 7.41 － 3/8-24 － 9.00 －. .7/16-20 － 10.48 10.541/2-20 － 12.07 12.13美制特细螺纹英制电器螺纹规格标准径 2级牙钻孔径规格钻孔径最大最小NO.12-32 4.70 4.826 4.623 2BA 4.0-4.21/4 -32 5.60 5.690 5.486 3BA5/16 -32 7.10 7.264 7.087 4BA 3.0-3.23/8 -32 8.70 8.865 8.661 5BA 2.7-2.87/16 -28 10.20 10.338 10.135 6BA 2.4-2.51/2 -28 11.80 11.938 11.7099/16 -24 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028螺丝攻牙钻孔径和滚丝径对照表英制螺纹公制螺纹针车用螺纹规格(UNEF) 钻孔径规格滚丝径规格滚丝径硬材软材W 1/8 - 40 2.65 2.60 M3×0.5 2.63-2.60 SM1/8-40 2.735-2.688W 5/32 - 32 3.25 3.20 M3.0×0.6 2.56-2.53 SM1/8-44 2.769-2.722W 3/16 - 24 3.75 3.70 M3.5×0.6 3.06-3.03 SM9/64-40 3.128-3.083 W 1/4 - 20 5.10 5.00 M4.0×0.7 3.49-3.45 SM11/64-40 3.855-3.805 W 5/16 - 18 6.60 6.50 M4.0×0.75 3.45-3.41 SM3/16-32 4.205-4.155 W 3/8 - 16 8.00 7.90 M4.5×0.75 3.96-3.92 SM3/16-28 4.143-4.093 W 7/16 - 14 9.40 9.30 M5.0×0.8 4.43-4.38 SM7/32-32 5.003-4.955 W 1/2 - 12 10.70 10.50 M5.0×0.9 4.36-4.31 SM15/64-28 5.325-5.570 W 9/16 - 12 12.30 12.00 M6.0×1.0 5.30-5.25 SM1/4-40 5.890-5.735 W 5/8 - 11 13.70 13.50 M7.0×1.0 6.30-6.25 SM1/4-28 5.721-5.366 W 3/4 - 10 16.70 16.50 M8.0×1.0 7.28-7.23 SM9/32-28 6.508-6.648 W 7/8 - 9 19.50 19.30 M8.0×1.25 7.12-7.07 SM11/32-28 8.092-8.432 W1 - 8 22.40 22.00 SM3/8-28 8.880-8.015W 1-1/8 - 7 25.00 24.80 SM7/16-28 10.466-10.401W 1 - 1/4 - 7 28.30 28.00 SM7/16-16 10.037-9.967SM1/2-20 11.819-11.749. v .SM9/26-20 13.400-13.425英制管螺纹英制管螺纹美制管螺纹规格标准径钻孔径规格标准径有交牙部之长度〔最小〕中之毋螺牙内径标准长度〔最小〕中之毋螺牙内径规格钻孔径最大最小使用绞刀时不用绞刀时 NPT NPS使用绞刀时不用绞刀时PS 1/16 - 28 6.50 6.632 6.490 PT 1/16 - 28 6.10 6.20 6.244 6.384 1/16 - 27 6.10 6.25 6.35PS 1/8 - 28 8.50 8.637 8.495 PT 1/8 - 28 8.10 8.20 8.249 8.388 1/8 - 278.33 8.43 8.74PS 1/4 - 19 11.40 11.549 11.341 PT 1/4 - 19 10.70 11.00 10.962 11.174 1/4 - 18 10.72 11.13 11.13PS 3/8 - 19 15.00 15.054 14.846 PT 3/8 - 19 14.20 14.50 14.448 14.658 3/8 - 18 14.27 14.27 14.68PS 1/2 - 14 18.50 18.773 18.489 PT 1/2 - 14 17.60 18.00 17.979 18.263 1/2 - 14 17.48 17.86 18.26PS 3/4 -14 24.00 24.259 23.975 PT 3/4 - 14 23.00 23.50 23.378 23.663 3/4 - 14 22.63 23.01 23.42PS 1 - 11 30.20 30.471 30.111 PT 1- 11 29.00 29.50 29.459 29.822 1 - 11-1/2 28.58 28.98 29.36PS 1-1/4 - 11 38.80 39.132 38.772 PT 1-1/4 - 11 37.50 38.00 37.976 38.339 1-1/4-11-1/2 37.31 37.69 38.10PS 1-1/2 - 11 44.80 45.025 44.665 PT 1-1/2 - 11 43.40 44.00 43.869 44.232 1-1/2-11-1/2 43.66 44.04 44.45PS 2 - 11 56.50 56.836 56.476 PT 2 - 11 54.90 55.50 55.412 55.844 2 - 11 - 1/2 55.58 55.96 56.36。

螺丝攻牙钻孔径和滚造径对照表本表所推选之钻头孔径，是针对攻牙加工时，能够很容易的了解钻孔直径；而依抿市售之标准钻头所选定的，在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸、精度有很大的影响，所以使用本表之钻孔径，若有不当之处，应视实际壮况适当的变更钻头直径，本表是依据2级牙最大最小最大最小G4-G6G7-G8G9G4-G6G7-G8G9硬材软材M1.0*0.250.750.7850.729M12*1.011.0011.15310.917M1.0*0.250.860.88-No 2 - 56UNC 1.94--W1/8 - 40 2.65 2.60M1.1*0.250.850.8850.829M12*0.511.5011.52011.400M1.1*0.250.960.98-No 3 - 48 2.23--W5/32 - 32 3.25 3.20M1.2*0.250.950.9850.929M14*1.512.5012.67612.376M1.2*0.25 1.06 1.08-No 4 - 40 2.50--W3/16 - 24 3.75 3.70M1.4*0.30 1.00 1.142 1.075M14*1.013.0013.15312.917M1.4*0.30 1.24 1.25-No 5 - 40 2.83--W1/4 - 20 5.10 5.00M1.6*0.35 1.25 1.321 1.221M15*1.513.5013.67613.376M1.6*0.35 1.41 1.43-No 6 - 32 3.07--W5/16 - 18 6.60 6.50M1.7*0.35 1.35 1.421 1.321M15*1.014.0014.15313.917M1.7*0.35 1.51 1.53-No 8 - 32 3.73 3.77-W3/8 - 168.007.90M1.8*0.35 1.45 1.521 1.421M16.1.514.5014.67614.376M1.8*0.35 1.61 1.63-No10 - 24 4.24 4.30-W7/16 - 149.409.30M2.0*0.40 1.60 1.679 1.567M16*1.015.0015.15314.917M2.0*0.40 1.78 1.80-No12 - 24 4.90 4.96-W1/2 - 1210.7010.50M2.2*0.45 1.75 1.838 1.713M17*1.515.5015.67615.376M2.2*0.45 1.95 1.98-1/4 - 20- 5.72-W9/16 - 1212.3012.00M2.3*0.40 1.90 1.979 1.867M17*1.016.0016.15315.917M2.3*0.40 2.08 2.10-5/16 - 18-7.24-W5/8 - 1113.7012.50M2.5*0.45 2.10 2.138 2.013M18*2.016.0016.21015.835M2.5*0.45 2.25 2.28-3/8 - 16-8.748.81W3/4 - 1016.7013.50M2.6*0.45 2.20 2.238 2.113M18*1.516.5016.67616.976M2.6*0.45 2.35 2.38-7/16 - 14-10.2010.30W7/8 - 919.5016.50M3.0*0.50 2.50 2.599 2.459M18*1.017.0017.15316.917M3.0*0.50 2.73 2.75-1/2 - 13-11.2711.82W1 - 822.4019.30M3.0*0.60 2.40 2.440 2.280M20*2.018.0018.21017.835M3.5*0.60 3.17 3.20-No 2 - 64UNF 1.97--W1-1/8 - 725.0024.80M3.5*0.60 2.90 3.010 2.850M20*1.518.5018.67618.376M4.0*0.70 3.62 3.65 3.69No 3 - 56 2.27--W1-1/4 - 728.3028.00M4.0*0.70 3.30 3.422 3.242M20*1.019.0019.15318.917M5.0*0.80 4.56 4.60 4.64No 4 - 48 2.56--M4.0*0.75 3.25 3.326 3.106M22*2.020.0020.21019.835M6.0*1.00 5.45 5.50 5.55No 5 - 44 2.66--M4.5*0.75 3.80 3.878 3.688M22*1.520.5020.67620.376M7.0*1.00 6.45 6.50 6.55No 6 - 40 3.16--M5.0*0.80 4.20 4.334 4.134M22*1.021.0021.15320.917M8.0*1.257.317.387.44No 8 - 36 3.78--M5.0*0.90 4.10 4.170 3.930M24*2.022.0022.21021.835M10*1.509.189.259.32No 10- 32 4.39 4.43-M6.0*1.00 5.00 5.153 4.917M24*1.522.5022.67622.376M10*1.259.319.389.44No 12 -28 4.99 5.04-M7.0*1.00 6.00 6.153 5.917M24*1.023.0023.15322.917M12*1.7511.0411.1211.211/4 -28 5.85 5.90-SM1/8 - 40 2.735 - 2.688M8.0*1.25 6.80 6.912 6.647M25*2.023.0023.21022.835M12*1.2511.3111.3811.445/16 -247.367.41-SM1/8 - 44 2.769 - 2.722M9.0*1.257.807.9127.647M25*1.523.5023.67623.3763/8 -24-9.00-SM9/64 - 40 3.128 - 3.083M10*1.508.508.6768.376M25*1.024.0024.15323.9177/16 -20-10.4810.54SM11/64 - 40 3.855 - 3.805M11*1.509.509.6769.376M26*1.524.5024.67624.3761/2 -20-12.0712.13SM3/16 - 32 4.205 - 4.155M12*1.7510.3010.44110.160M27*2.025.0025.21024.835SM3/16 - 28 4.143 - 4.093M14*2.0012.0012.21011.835M27*1.525.5025.67625.376SM7/32 - 32 5.003 - 4.955M16*2.0014.0014.21013.835M27*1.026.0026.15325.917SM15/64 - 28 5.325 - 5.570M18*2.5015.5015.74415.294M28*2.026.0026.21025.835SM1/4 - 40 5.890 - 5.735M20*2.5017.5017.74417.294M28*1.526.5026.67626.376SM1/4 - 28 5.721 - 5.366M22*2.5019.5019.74419.294M28*1.027.0027.15326.917最大最小SM9/32 - 28 6.508 - 5.648M24*3.0021.0021.25220.752M30*3.027.0027.15226.752最大最小PS 1/16 - 28 6.50 6.632 6.490SM11/32 - 288.092 - 8.432M27*3.0024.0024.25223.752M30*2.028.0028.21027.835No 1-64(1.854) 1.55 1.582 1.425PS 1/8 - 288.508.6378.495SM3/8 - 288.880 - 8.015M30*3.5026.5026.77126.211M30*1.528.5028.67628.376No 2-56(2.184) 1.80 1.871 1.695PS 1/4 - 1911.4011.54911.341SM7/16 - 2810.466 - 10.401M30*1.029.0029.15328.917No 3-48(2.515) 2.10 2.146 1.941PS 3/8 - 1915.0015.05414.846SM7/16 - 1610.037 - 9.967M32*2.030.0030.21029.835No 4-40(2.845) 2.30 2.385 2.157PS 1/2 - 1418.5018.77318.489SM1/2 - 2011.819 - 11.749M32*1.530.5030.67630.376No 5-40(3.175) 2.60 2.697 2.487PS 3/4 - 1424.0024.25923.975SM9/16 - 2013.400 - 13.425最大最小M33*1.030.0030.25229.752No 6-32(3.505) 2.80 2.895 2.642PS 1 - 1130.2030.47130.111M1.0*0.20.800.8210.783M33*2.031.0031.21030.835No 8-32(4.166) 3.40 3.530 3.302PS 1-1/4 - 1138.8039.13238.772M1.1*0.20.900.9210.883M33*1.531.5031.67631.376No 10-24(4.826) 3.90 3.962 3.683PS 1-1/2 - 1144.8045.02544.665M1.2*0.2 1.00 1.0210.983M35*1.533.5033.67633.376No 12-24(5.486) 4.50 4.597 4.344PS 2 - 1156.5056.83656.476M1.4*0.2 1.20 1.221 1.183M36*3.033.0033.25232.752 1/4 - 20 5.10 5.257 4.979M1.6*0.2 1.40 1.421 1.383M36*2.034.0034.21033.835 5/16 - 18 6.60 6.731 6.401M1.7*0.2 1.45 1.500 1.460M36*1.534.5034.67634.376 3/8 - 168.008.1537.798M3*0.5 2.63 - 2.60M1.8*0.2 1.60 1.621 1.583 7/16 - 149.409.5509.144M3.0*0.6 2.56 - 2.50M2.0*0.25 1.75 1.785 1.7291/2 - 1310.8011.02310.592M3.5*0.6 3.06 - 3.03M2.2*0.25 1.95 1.985 1.929 9/16 - 1212.2012.44611.989使用绞刀时不使用绞刀时M4.0*0.7 3.49 - 3.45M2.3*0.25 2.05 2.610 2.0015/8 - 1113.6012.86813.386PT 1/16 - 28 6.10 6.20 6.244 6.384M4.0*0.75 3.45 - 3.41M2.5*0.35 2.20 2.221 2.121最大最小 3/4 - 1016.5018.84016.307PT 1/8 - 288.108.208.2498.388M4.5*.75 3.96 - 3.92M2.6*0.35 2.20 2.246 2.186No 0-80(1.524) 1.25 1.305 1.182 7/8 - 919.5019.76119.177PT 1/4 - 1910.7011.0010.96211.174M5.0*0.8 4.43 - 4.38M3.0*0.35 2.70 2.721 2.621No 1-72(1.854) 1.55 1.612 1.474 1 - 822.2022.60621.971PT 3/8 - 1914.2014.5014.44814.658M5.0*0.9 4.36 - 4.31M3.5*0.35 3.20 3.221 3.121No 2-64(2.184) 1.85 1.912 1.756 1-1/8 - 725.0025.34924.638PT 1/2 - 1417.6018.0017.97918.263M6.0*1.0 5.30 - 5.25M4.0*0.5 3.50 3.599 3.459No 3-58(2.515) 2.10 2.197 2.025 1-1/4 - 728.2028.52427.813PT 3/4 - 1423.0023.5023.37823.663M7.0*1.0 6.30 - 6.25M4.5*0.5 4.00 4.099 3.959No 4-48(2.845) 2.40 2.458 2.271 1-3/8 - 630.8031.11530.353PT 1 - 1129.0029.5029.45929.822M8.0*1.07.28 - 7.23M5.0*0.5 4.50 4.599 4.459No 5-44(3.175) 2.70 2.740 2.551 1-1/2 - 634.0034.29033.528PT 1-1/4 - 1137.5038.0037.97638.339M8.0*1.257.12 - 7.07M5.5*0.5 5.00 5.099 4.959No 6-40(3.506) 2.90 3.022 2.820 1-3/4 - 539.5039.82738.964PT 1-1/2 - 1143.4044.0043.86944.232M6.0*0.75 5.30 5.378 5.188No 8-36(4.166) 3.50 3.606 3.404 2 - 4-1/245.2045.59344.679PT 2 - 1154.9055.5055.41255.844M6.0*0.5 5.50 5.550 5.400No 10-32(4.826) 4.10 4.165 3.963M7.0*0.75 6.30 6.378 6.188No 12-28(5.846) 4.60 4.724 4.496M7.0*0.5 6.50 6.550 6.4001/4 - 28 5.50 5.588 5.360M8.0*1.07.007.153 6.9175/16 - 24 6.907.035 6.782M8.0*0.757.307.3787.1883/8 - 248.508.6368.382最大最小M8.0*0.57.507.5207.4007/16 - 209.9010.0339.729No 12 - 32 4.700 4.826 4.623使用绞刀时不使用绞刀时2BA 4.0 - 4.2M9.0*1.08.008.1537.9171/2 - 2011.5011.60711.3291/4 - 32 5.600 5.690 5.4861/16 - 27 6.10 6.25 6.353BA M9.0*0.758.308.3788.1889/16 - 1812.9013.08112.7515/16 - 327.1007.2647.0871/8 - 278.338.438.744BA 3.0 - 3.2M10*1.258.808.9128.6475/8 - 1814.5014.68114.3513/8 - 328.7008.8658.6611/4 -1810.7211.1311.135BA 2.7 - 2.8M10*1.09.009.1538.9173/4 - 1617.5017.67817.3237/16 - 2810.20010.33810.1353/8 -1814.2714.2714.686BA 2.4 - 2.5M10*0.759.309.3789.1887/8 - 1420.5020.57520.2701/2 - 2811.80011.93811.7091/2 -1417.4817.8618.26M10*0.59.509.5209.400 1 - 1223.2023.57123.1149/16 - 2413.20013.38613.1323/4 -1422.6323.0123.42M11*1.010.0010.1538.9171-1/8 - 1226.5026.74626.2895/8 - 2414.80014.98614.732 1 -11-1/228.5828.9829.36M11*0.7510.3010.37810.1881-1/4 - 1229.5029.92129.4643/4 - 2017.80017.95817.6781-1/4-11-1/237.3137.6938.10M12*1.5010.5010.67610.3761-3/8 - 1232.8033.09632.6397/8 - 2021.00021.13320.8531-1/2-11-1/243.6644.0444.45M12*1.2510.8010.91210.6471-1/2 - 1236.0036.27135.814 1 - 2024.00024.30824.028 2 -11-1/255.5855.9656.36规格钻孔径规格滚造径英制电器螺纹公制螺纹规格滚造径2级牙钻孔径NPT英 制 管 螺 纹英 制 管 螺 纹规格标准径有效牙部之长度（最小）中之毋螺牙内径标准长度（最小）中之毋螺牙内径规格(UNC)标准径规格标准率规格(UNF)标准径2级牙钻孔径规格2级牙钻孔径规格(UNC)标准径2级牙钻孔径注:迫牙丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质,硬度,形状,尺寸等之影响,多少会有所变动,因此于参考上表之同时,亦精增减若干。

螺丝攻牙钻孔径和滚丝径对照表螺丝攻牙钻孔径和滚丝径对照表公制粗螺纹美制粗螺纹规格标准径2级牙钻孔径规格（UNC）标准径2级牙钻孔径最大最小最大最小M1.0×0.25 0.75 0.785 0.729NO.1-64(1.854) 1.55 1.582 1.425M1.1×0.25 0.85 0.885 0.829NO.2-56(2.184) 1.80 1.871 1.695M1.2×0.25 0.95 0.985 0.985NO.3-48(2.515) 2.10 2.146 1.941M1.4×0.3 1.10 1.142 1.075NO.4-40(2.845) 2.30 2.385 2.157M1.6×0.35 1.25 1.321 1.221NO.5-40(3.175) 2.60 2.697 2.487M1.7×0.35 1.35 1.421 1.321NO.6-32(3.505) 2.80 2.895 2.642M1.8×0.35 1.45 1.521 1.421NO8-32(4.166) 3.40 3.53 3.302M2.0×0.4 1.60 1.679 1.567NO.10-24(4.826) 3.90 3.962 3.683M2.2×0.45 1.75 1.838 1.713NO.12-24(5.486) 4.50 4.597 4.344M2.3×0.4 1.90 1.979 1.867 1/4-20 5.10 5.257 4.979M2.5×0.45 2.10 2.138 2.013 5/16-18 6.60 6.731 6.401M2.6×0.45 2.20 2.238 2.113 3/8-16 8.00 8.153 7.798M3.0×0.5 2.50 2.599 2.459 7/16-14 9.40 9.55 9.144M3.0×0.6 2.40 2.440 2.280 1/2-13 10.80 11.023 10.592M3.5×0.6 2.90 3.010 2.850 9/16-12 12.20 12.446 11.989M4.0×0.7 3.30 3.422 3.242 5/8-11 13.60 12.868 13.386M4.0×0.75 3.25 3.326 3.106 3/4-10 16.50 18.840 16.307M4.5×0.75 3.80 3.878 3.688 7/8-9 19.50 19.761 19.177M5.0×0.8 4.20 4.334 4.134 1 22.2022.606 21.971M5.0×0.9 4.10 4.170 3.930 1-1/8-7 25.00 25.349 24.638M6.0×1.0 5.00 5.153 4.917 1-1/4-7 28.20 28.524 27.813M7.0×1.0 6.00 6.153 5.917 1-3/8-6 30.80 31.115 30.353M8.0×1.25 6.80 6.912 6.647 1-1/2-6 34.00 34.290 33.528M9.0×1.25 7.80 7.912 7.647 1-3/4-5 39.50 39.827 38.964M10×1.5 8.50 8.676 8.376 2-4-1/2 45.20 45.593 44.679M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.835M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 20.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211螺丝攻牙钻孔径和滚丝径对照表公制细螺纹美制细螺纹规格标准径2级牙钻孔径规格（UNC）标准径2级牙钻孔径最大最小最大最小M1.0×0.2 0.80 0.821 0.783 NO.0-80(1.524) 1.25 1.305 1.182M1.1×0.2 0.90 0.921 0.883 NO.1-72(1.854) 1.55 1.612 1.474M1.2×0.2 1.00 1.021 0.983 NO.2-64(2.184) 1.85 1.912 1.756M1.4×0.2 1.20 1.221 1.183 NO.3-56(2.515) 2.10 2.197 2.025M1.6×0.2 1.40 1.421 1.383 NO.4-48(2.845) 2.40 2.458 2.271M1.7×0.2 1.45 1.500 1.460NO.5-44(3.175) 2.70 2.740 2.551M1.8×0.2 1.60 1.621 1.583NO.6-40(3.505) 2.90 3.022 2.820M2.0×0.25 1.75 1.785 1.729NO.8-36(4.166) 3.50 3.606 3.404M2.2×0.25 1.95 1.985 1.929NO.10-32(4.826) 4.10 4.165 3.963M2.3×0.25 2.05 2.061 2.001NO.12-28(5.846) 4.60 4.724 4.496M2.5×0.35 2.20 2.221 2.121 1/4-28 5.50 5.588 5.360M2.6×0.35 2.20 2.246 2.186 5/16-24 6.90 7.035 6.782M3.0×0.35 2.70 2.721 2.621 3/8-24 8.50 8.636 8.382M3.5×0.35 3.20 3.221 3.121 7/16-20 9.90 10.033 9.729M4.0×0.5 3.50 3.599 3.459 1/2-20 11.50 11.607 11.329M4.5×0.5 4.00 4.099 3.959 9/16-18 12.90 13.081 12.751M5.0×0.5 4.50 4.599 4.459 5/8-18 14.50 14.681 14.351M5.5×0.5 5.00 5.099 4.959 3/4-16 17.50 17.678 17.323M6.0×0.75 5.30 5.378 5.188 7/8-14 20.50 20.675 20.270M6.0×0.5 5.50 5.550 5.400 1-12 23.20 23.571 23.114M7.0×0.75 6.30 6.378 6.188 1-1/8-12 26.50 26.746 26.289M7.0×0.5 6.50 6.550 6.400 1-1/4-1229.50 29.921 29.464M8.0×1.0 7.00 7.153 6.917 1-3/8-12 32.80 33.096 32.639M8.0×0.75 7.30 7.378 7.188 1-1/2-12 36.00 36.271 35.814M8.0×0.5 7.50 7.520 7.400M9.0×1.0 8.00 8.153 7.917M9.0×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188M12×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647M12×0.5 11.50 11.520 11.400 M14×1.5 12.50 12.676 12.376 M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.676 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M22×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376 M22×1.0 21.00 21.153 20.917M24×1.5 22.50 22.676 22.376 M24×1.0 23.00 23.153 22.917 M25×2.0 23.00 23.210 22.835 M25×1.5 23.50 23.676 23.376 M25×1.0 24.00 24.153 23.917 M26×1.5 24.50 24.676 24.376 M27×2.0 25.00 25.210 24.835 M27×1.5 25.50 25.676 25.376 M27×1.0 26.00 26.153 25.917 M28×2.0 26.00 26.210 25.835 M28×1.5 26.50 26.676 26.376 M28×1.0 27.00 27.153 26.917 M30×3.0 27.00 27.252 26.752 M30×2.0 28.00 28.210 27.835 M30×1.5 28.50 28.676 28.376 M30×1.0 29.00 29.153 28.917 M32×2.0 30.00 30.210 29.835 M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.676 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376螺丝攻牙钻孔径和滚丝径对照表公制挤压丝攻钻孔径美制挤压丝攻钻孔径规格精度等级规格（UNC）精度等级G4-G6 G7-G8 G9 G4-G6 G7-G8 G9M1.0×0.25 0.86 0.88 －NO.2-56UNC 1.94 －－M1.1×0.25 0.96 0.98 －NO.3-48 2.23 －－M1.2×0.25 1.06 1.08 －NO.4-40 2.50 －－M1.4×0.3 1.24 1.25 －NO.5-40 2.83 －－M1.6×0.35 1.41 1.43 －NO.6-32 3.07 －－－M1.8×0.35 1.61 1.63 －NO.10-24 4.24 4.3 －M2.0×0.4 1.78 1.80 －NO.12-24 4.90 4.96 －M2.2×0.45 1.95 1.98 －1/4-20 －5.72 －M2.3×0.4 2.08 2.10 －5/16-18 －7.24 －M2.5×0.45 2.25 2.28 －3/8-16 －8.74 8.81 M2.6×0.45 2.35 2.38 －7/16-14 －10.20 10.30M3.0×0.5 2.73 2.75 －1/2-13 －11.27 11.82M3.5×0.6 3.17 3.20 －NO.2-64UNF 1.97－－M4.0×0.7 3.62 3.65 3.69 NO.3-56 2.27 －－M5.0×0.8 4.56 4.60 4.64 NO.4-48 2.56 －－－M7.0×1.0 6.45 6.50 6.55 NO.6-40 3.16 －－M8.0×1.25 7.31 7.38 7.44 NO.8-36 3.78 －－M10×1.5 9.18 9.25 9.32 NO.10-32 4.394.43 －M10×1.25 9.31 9.38 9.44 NO.12-28 4.99 5.04 －M12×1.75 11.04 11.12 11.21 1/4-28 5.85 5.90 －M12×1.25 11.31 11.38 11.44 5/16-24 7.36 7.41 －3/8-24 －9.00 －7/16-20 －10.48 10.541/2-20 －12.07 12.13美制特细螺纹英制电器螺纹规格标准径2级牙钻孔径规格钻孔径最大最小NO.12-32 4.70 4.826 4.623 2BA 4.0-4.2 1/4 -32 5.60 5.690 5.486 3BA5/16 -32 7.10 7.264 7.087 4BA 3.0-3.2 3/8 -32 8.70 8.865 8.661 5BA 2.7-2.8 7/16 -28 10.20 10.338 10.135 6BA 2.4-2.51/2 -28 11.80 11.938 11.7099/16 -24 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028螺丝攻牙钻孔径和滚丝径对照表英制螺纹公制螺纹针车用螺纹规格(UNEF) 钻孔径规格滚丝径规格滚丝径硬材软材W 1/8 - 40 2.65 2.60 M3×0.5 2.63-2.60SM1/8-40 2.735-2.688W 5/32 - 32 3.25 3.20 M3.0×0.6 2.56-2.53 SM1/8-44 2.769-2.722W 3/16 - 24 3.75 3.70 M3.5×0.6 3.06-3.03 SM9/64-40 3.128-3.083W 1/4 - 20 5.10 5.00 M4.0×0.7 3.49-3.45 SM11/64-40 3.855-3.805W 5/16 - 18 6.60 6.50 M4.0×0.75 3.45-3.41 SM3/16-32 4.205-4.155W 3/8 - 16 8.00 7.90 M4.5×0.75 3.96-3.92 SM3/16-28 4.143-4.093W 7/16 - 14 9.40 9.30 M5.0×0.8 4.43-4.38 SM7/32-32 5.003-4.955W 1/2 - 12 10.70 10.50 M5.0×0.9 4.36-4.31 SM15/64-28 5.325-5.570W 9/16 - 12 12.30 12.00 M6.0×1.05.30-5.25 SM1/4-40 5.890-5.735W 5/8 - 11 13.70 13.50 M7.0×1.0 6.30-6.25 SM1/4-28 5.721-5.366W 3/4 - 10 16.70 16.50 M8.0×1.0 7.28-7.23 SM9/32-28 6.508-6.648W 7/8 - 9 19.50 19.30 M8.0×1.25 7.12-7.07 SM11/32-28 8.092-8.432W1 - 8 22.40 22.00 SM3/8-288.880-8.015W 1-1/8 - 7 25.00 24.80 SM7/16-28 10.466-10.401W 1 - 1/4 - 7 28.30 28.00 SM7/16-16 10.037-9.967SM1/2-20 11.819-11.749SM9/26-20 13.400-13.425英制管螺纹英制管螺纹美制管螺纹规格标准径钻孔径规格标准径有交牙部之长度（最小）中之毋螺牙内径标准长度（最小）中之毋螺牙内径规格钻孔径最大最小使用绞刀时不用绞刀时NPT NPS 使用绞刀时不用绞刀时PS 1/16 - 28 6.50 6.632 6.490 PT 1/16 - 28 6.10 6.20 6.244 6.384 1/16 - 27 6.10 6.25 6.35PS 1/8 - 28 8.50 8.637 8.495 PT 1/8 - 28 8.10 8.20 8.249 8.388 1/8 - 27 8.33 8.43 8.74PS 1/4 - 19 11.40 11.549 11.341 PT 1/4 - 19 10.70 11.00 10.962 11.174 1/4 - 18 10.72 11.13 11.13PS 3/8 - 19 15.00 15.054 14.846 PT 3/8 - 19 14.20 14.50 14.448 14.658 3/8 - 18 14.27 14.27 14.68PS 1/2 - 14 18.50 18.773 18.489 PT 1/2 - 14 17.60 18.00 17.979 18.263 1/2 - 14 17.48 17.86 18.26PS 3/4 -14 24.00 24.259 23.975 PT 3/4 - 14 23.00 23.50 23.378 23.663 3/4 - 14 22.63 23.01 23.42PS 1 - 11 30.20 30.471 30.111 PT 1- 11 29.00 29.50 29.459 29.822 1 - 11-1/2 28.58 28.98 29.36PS 1-1/4 - 11 38.80 39.132 38.772 PT 1-1/4 - 11 37.50 38.00 37.976 38.3391-1/4-11-1/2 37.31 37.69 38.10PS 1-1/2 - 11 44.80 45.025 44.665 PT 1-1/2 - 11 43.40 44.00 43.869 44.2321-1/2-11-1/2 43.66 44.04 44.45PS 2 - 11 56.50 56.836 56.476 PT 2 - 11 54.90 55.50 55.412 55.844 2 - 11 - 1/2 55.58 55.96 56.36。

当之处，应视实际状况适当的变更钻头直径。

本表是依据2级牙制订。

注：迫牙丝攻之钻孔径，在上表所列之数
值，由于被加工 材料之材质、硬度、形状
、尺寸等之影响，多少会有所变动，因此
于参考上表之同时，亦请增减若干。

螺纹攻牙钻孔径和滚造径对照表
本表所推选之钻头孔径，是针对攻牙加工时，能够很容易的了解钻孔直径；而依据市售之标准钻头所选定的。

在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸、精度有很大的影响，所以使用本表之钻孔径，若有不。

螺丝攻牙钻孔径和滚造径对照表螺丝攻牙钻孔径和滚造径对照表公制粗螺纹美制粗螺纹规格标准径2级牙钻规格（UN标准2级牙钻最大最小最大最小M1.0×0.25 0.70.70.7NO.1-1.51.5 1.4 M1.1×0.25 0.80.80.8NO.2-1.81.8 1.6 M1.2×0.25 0.90.90.9NO.3-2.12.1 1.9 M1.4×0.3 1.1 1.1 1.0NO.4-2.32.3 2.1 M1.6×0.35 1.2 1.3 1.2NO.5-2.62.6 2.4 M1.7×0.35 1.3 1.4 1.3NO.6-2.82.8 2.6 M1.8×0.35 1.4 1.5 1.4NO8- 3.43.5 3.3 M2.0×0.4 1.6 1.6 1.5NO.1 3.93.9 3.6 M2.2×0.45 1.7 1.8 1.7NO.1 4.54.5 4.3 M2.3×0.4 1.9 1.9 1.81/4- 5.15.2 4.9 M2.5×0.45 2.1 2.1 2.05/16-6.66.7 6.4 M2.6×0.45 2.2 2.2 2.13/8-8.08.17.7 M3.0×0.5 2.5 2.5 2.47/16-9.49.59.1 M3.0×0.6 2.4 2.4 2.21/2-10.11.10. M3.5×0.6 2.9 3.0 2.89/16-12.12.11. M4.0×0.7 3.3 3.4 3.25/8-13.12.13. M4.0×0.75 3.2 3.3 3.13/4-16.18.16. M4.5×0.75 3.8 3.8 3.67/8-9 19.19.19. M5.0×0.8 4.2 4.3 4.1 1 22.22.21. M5.0×0.9 4.1 4.1 3.91-25.25.24. M6.0×1.0 5.0 5.1 4.91-28.28.27. M7.0×1.0 6.0 6.1 5.91-30.31.30. M8.0×1.25 6.8 6.9 6.61-34.34.33. M9.0×1.25 7.87.97.61-39.39.38. M10×1.5 8.58.68.32-4-45.45.44. M11×1.5 9.59.69.3M12×1.75 10.10.10.M14×2.0 12.12.11.M16×2.0 14.14.13.M18×2.5 15.15.15.M20×2.5 17.17.17.M22×2.5 19.19.19.M24×3.0 21.21.20.M27×3.0 24.24.23.M30×3.5 26.26.26.M16丝孔钻14。