EIA-364-35A

PRODUCT SPECIFICATION SPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 Name PRODUCT SPECIFICATION Amended Date 05-29-2003TYPEPLUG&RECEPTACLE Page 1 Sum To 8 PagesA&BTitle USB2.0１．SCOPEThis specification covers performance, methods and quality requirements forUniversal Serial Bus (USB) plug and receptacle connectors. These connectorsare cable mounted plug and printed circuit board mounted receptacle connectors.2. REQUIREMENTS2.1 Design and ConstructionProduct shall be of the design , construction and physical dimensions specifiedThe in applicable product drawing.2.2 Materials and PlatingThey are specified on applicable product drawing.2.3 RatingsA.Voltage: 30 VAC (rms)B.Current: 1.5A per contact, not to exceed 30℃ temperature riseC.Operating temperature: -20℃ to +85℃D.Storage temperature: -25℃ to +85℃E.Nominal Temperature Rating: +20℃2.4 Test Requirements and Procedures SummaryD Amended 05-29-2003Check Director Tab C Amended 10-17-2001A Approved 02-26-2001陈永飞Description DateItem ChangePRODUCT SPECIFICATIONSPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 NamePRODUCT SPECIFICATIONAmended Date05-29-2003Title USB2.0 A&B TYPE PLUG&RECEPTACLE Page 2 Sum To 8 PagesNote:Shall meet visual requirements ,show no physical damage ,and shall meet requiremFigure 1 (conn.)Test DescriptionRequirement ProcedureLow level contact resistance for Lower and Middle stack 30mΩ maximum initial EIA 364-23 Subject mated contacts assembled in housing to 20 mV maximum open circuit at 100 mA maximum. See figure ALow level contact resistance for Upper stack 50mΩ maximum initial EIA 364-23 Subject mated contacts assembled in housing to 20 mV maximum open circuit at 100 mA maximum. See figure AInsulation resistance 1000 MΩ minimum EIA 364 – 21 Test voltage 500±50V/DC between adjacent contacts of mated and unmated connector assemblies.Dielectric withstanding Voltage No flashover&sparkover&excess leakage&breakdownEIA 364 – 20 Test voltage 500V/AC between adjacent contacts of mated and unmated connector assemblies.Vibration , random No discontinuities of 1u s orLonger duration.See Note.EIA 364 – 28A-83 Condition V Test Letter A. Subject mated connectors to 5.35 G's rms. 15 minutes in each of three mutually perpendicular planes ,See Figure B.Physical shock No discontinuities of 1u s or Longer duration.See Note. EIA 364 – 27 Condition H. Subject mated connectors to 30 Gs half-sine shock' pulses of 11 ms duration. three shocks in each direction applied along three mutually perpendicular planes ,18 total shocks ,See Figure C first test setup.Durability Contact Resistance:10 mΩ maximum change from initial value. EIA 364 – 09. 1500cycles insertion/extraction at a maximum rate of 200cycles per hour, then see note. Solderability USB contact solder tails shall pass95% coverage after one hour steam aging as specified in category 2.EIA364--52Cable pull-out Applied a load of 40 Newtons for one minute.EIA364-38 Test condition APRODUCT SPECIFICATION SPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 Name PRODUCT SPECIFICATION Amended Date 05-29-2003 Title USB2.0A&BTYPEPLUG&RECEPTACLE Page 3 Sum To 8 Pages Test Description Requirement ProcedureMating force 35 Newtons maximumEIA 364 – 13 Measure forcenecessary to mate connector Assembliesat maximum rate of 12.5 mm/min.Unmating force 10 Newtons minimumEIA 364 – 13 Measure forcenecessary to unmate connectorassemblies at maximum rate of 12.5mm/min.Thermal shock Contact Resistance:10 mΩ maximumchange from initial value.EIA 364 –32 Test Condition I.10Cycles –55℃ and +85℃,The USBconnectors under test must be mated.Critical Dimension 8 total measurement within tolerance.EIA 364-18Humidity Life Contact Resistance:10 mΩ maximumchange from initial value. The USB connectors under test must betested in accordance with EIA 364 – 31Condition A. method Ш. 168 Hours minimum (seven complete cycles).Temperature life Contact Resistance:10 mΩ maximumchange from initial value. See NoteEIA 364 – 17A-87 Condition 2 MethodA. Subject mated connectors totemperature Life at 85℃ for 250 hoursMixed Flowing Gas See NoteEIA 364-65-92 Class II, Exposures(1)U nmated for 1 day(2)M ated for 10 dayFlammability Require its thermoplastic resin vendorto supply a detailed C of C with eachresin shipment. The C of C shallclearly show the resin’s UL listingnumber, lot number, date code, etc.UL 94 v-0Note:Shall meet visual requirements ,show no physical damage ,and shall meet requirement.Figure 1 (conn.)PRODUCT SPECIFICATION SPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 Name PRODUCT SPECIFICATION Amended Date 05-29-2003 Title USB2.0A&BTYPEPLUG&RECEPTACLE Page 4 Sum To 8 Pages Test Description Requirement ProcedureContact capacitance 2 pF maximum unmated percontact.EIA 364 –30The object of this test is to detail a standardmethod to determine the capacitance betweenconductive elements of a USB connector.Contact current rating 1.5A at 250vAC minimumwhen measured at an ambienttemperature of 25℃, withpower applied to the contacts,the temperature change shallnot exceed +30 at any point inthe USB connector under test.EIA 364 – 70—method BThe object of this test procedure is to detail astandard method to assess the currentcarrying capacity of mated USB connectorcontacts.Differential impedance 90±15%Ω(76.5~~103.5Ω)Connect the Time Domain Reflectometer(TDR). TDR is setup the differential mode.Common mode impedance 30±30%Ω(21~~39Ω)Connect the Time Domain Reflectometer(TDR). TDR is setup the differential mode.Propagation Delay 26ns(maximum for full speed cable)Connect the Time Domain Reflectometer(TDR). TDR is setup the differential mode.Propagation delay skew 100ps/cable(maximum for full speed cable)Connect the Time Domain Reflectometer (TDR). TDR is setup the differential mode.Signal pair attenuation (Maximum) 0.064 MHz 0.08 dB/Cable1. Connect the Network Analyzer output port(port1) to the input connector on theattenuation test fixture(note).2. Connect the series “A” plug of the cable obe tested to the test fixture, leaving theother end open-circuited.3.Calibrate the network analyzer andfixture using the appropriate calibrationstandards over the desired frequencyrange.0.256 MHz 0.11 dB/Cable0.512 MHz 0.13 dB/Cable0.772 MHz 0.15 dB/Cable1.000 MHz 0.20 dB/Cable4.000 MHz 0.39 dB/Cable8.000 MHz 0.57 dB/Cable12.00 MHz 0.67 dB/Cable24.00 MHz 0.95 dB/Cable48.00 MHz 1.35 dB/Cable96.00 MHz 1.90 dB/Cable200.00 MHz 3.2 dB/Cable400.00 MHz 5.8 dB/CableNote: Shall meet visual requirements ,show no physical damage ,and shall meet requirementFigure 1 (conn.)PRODUCT SPECIFICATION SPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 Name PRODUCT SPECIFICATION Amended Date 05-29-2003 Title USB2.0A&BTYPEPLUG&RECEPTACLE Page 5 Sum To 8 Pages 2.5 Product qualification test sequence:Test ExaminationTest Group (a)1 2 3 4 5 6 8Test Sequence (b)Examination 1,10 1,6 1,6 1,9 1,3 1,6 1,3 Low level contactresistance3,7 2,5 2,5Capacitance 2Critical Dimension 2 Insulation resistance 3,7DWV 4,8Vibration 5Physical shock 6Durabillity 4 3 3Mating and unmatingforce2,8Thermal shock 5Humidity 6Temperature life 4Cable pull-out 9Mixed Flowing Gas 4Solderability 2Impedance 2Attenuation 3 Propagation delay 4Skew 5Number of samplesPlug 8pcs 8pcs 8pcs 8pcs 5pcs 5pcs 8pcs socket 8pcs 8pcs 8pcs 8pcs 5pcs 5pcs8pcs3. Sample Selection:Samples shall be prepared in accordance with applicable manufacturers instructions and shall be selected at random form current productions.PRODUCT SPECIFICATIONSPEC.NO. SPEC-USB 2.0Approved Date 02-26-2001 Name PRODUCTSPECIFICATION Amended Date05-29-2003TitleUSB2.0 A&B TYPE PLUG&RECEPTACLEPage 8 Sum To 8 Pages1.0 USB connector termination data:provide the standardized contact terminating assignments by number and electricalvalue for series “A” and series “B” connectors.1.1 USB connector termination assignment:Contact numberSignal nameTypical wiring Assignment1 Vbus Red2 D- White3 D+ Green4 GND Black shell Shield Drain Wire。

参考标准：IEC60950/EN60950/UL60950/GB4943、IEC60332/GB/T18380、UL1581
30
环保要求
本技术要求数据线所有组成材料符合ROHS要求,Reach要求.
外背jacket无断裂；
连接器与线缆无分离；
芯线端点无脱离连接器；
电气性能正常；
导通阻抗符合规格要求，并记录实际值
EIA 364-41
6
滚筒跌落
跌落高度1米，跌落次数150次，每50检查一次，跌落速度参考值10-12次/分次（以跌落在滚筒铁板中心位置为准）
测试完成线缆无损坏，松脱；
连接器可以无明显尺寸变化；
修订履历
版本
修订内容
日期
修/制订者
审核
批准
A/0
新制订
2017-03-03
Peter
Mils
YANG
可靠性测试规范：
Test condition
Temperature：15℃ to 35℃
Air pressure ：86 to106 kPa
Relativehumidity：25% to 85%
NO
Test description
29
阻燃要求
VW-1（北美）,满足IEC60332或GB/T18380电缆在火焰条件下的燃烧试验标准（欧洲、国内）。
参考标准：IEC60950/EN60950/UL60950/GB4943、IEC60332/GB/T18380、UL1581
满足IEC60332或GB/T18380电缆在火焰条件下的燃烧试验标准（欧洲、国内）。
Micro USB插拔耐久测试前后：拔出力大于等于8N，小于等于20N
EIA364-13

3.6. 電器性能要求
3.6.1 耐電流耐電壓: 測試參照標準 EIA-364-20B.最大 3.0A, 周圍溫升不超過 30 度, 耐電壓 250 V AC. 3.6.2 低壓電流阻抗: 測試參照標準 EIA-364-23B，應小於 20mΩ.壽命測試後應小於 30mΩ. 3.6.3 絕緣電壓測試: 測試參照標準 EIA-364-20B,漏電流應小於 0.1mA.測試條件如下: A. 電壓: 600V AC at 50HZ. B. 延遲時間: 60 秒
A. 樣品選擇: 樣品需按照隨機從在制產品中抽取,抽取數量 18 個. B. 測試順序: (見下頁) 測試項目 樣本大小 尺寸檢查 端子接觸阻抗測試 絕緣阻抗測試 耐電壓耐電流測試 絕緣電壓測試 高低溫恆溫恆濕測試 溼度測試 耐高溫測試 低溫測試 鹽霧實驗 保持力測試 壽命測試
A 2 1 2
B 2 1,8 2,7 6
4. 質量確認規定
4.1 測試環境:
A. 溫度: 25± 2℃. B. 相對溼度: 30%到 60%.
Greenconn
®
PRODUCT SPECIFICATION
File NO. Date
PS-PHA(B)101 2003/9/26
Page 6/7 Rev. A/0
C. 氣壓: 自然環境
4.2 質量檢查:
Greenconn
A. B.
®
PRODUCT SPECIFICATION
File NO. Date
PS-PHA(B)101 2003/9/26
Page 5/7 Rev. A/0
測試條件: 試驗室溫度 35±2℃,24 小時,5% NaCL 質量濃度. 特殊處理: 端子從鹽水中拿出後,需用清水沖洗,並允許室溫下乾燥 24 小時.

TYPE C数据线规格‎书V1.0关键词：TYPE C、数据线摘要：本文介绍了数‎据线的规格，性能及测试规‎范。

缩略语：1范围标准适用于TYPE A TO C数据线需求‎规格书，未尽规格描述‎以TY PE C协会规范V‎1.1为准。

2编写依据3数据线正常工‎作和存储条件‎3.1数据线应能在‎下列条件下正‎常工作：3.1.1 工作环境温度‎：-20℃～+55℃；（仅作单体验证‎目的，与整机匹配时‎以整机试验环‎境为准）；3.1.2 相对湿度：5%～95%；3.1.3 大气压力：86 kPa～106kPa‎;3.1.4 数据线的存储‎温度：-40℃～+85℃；4数据线主要参‎数4.1数据线连线规‎格详细尺寸以及‎工艺要求以3‎D图档为准1、type C金属插头，要求必须是整‎体拉伸成型，不能是折弯成‎型，不接受接缝；2、金属插头部分‎，要求做不锈钢‎原色，表面喷砂处理‎:50u”~150u”MA TT NICK EL‎PLA TIN‎G OVER ALL3、保证至少3A‎通流能力整条线缆产品‎详细规格（BOM清单, 包括端子图纸‎2D& 可拆解版本的‎3D）要有确认才能‎认可(认证时必须提‎供以上文件)。

4.2线材主体信息‎：4.2.1外观5V/3A A plug TO C plug, cover式‎，白色半雾面,素材细咬花处‎理，MT1100‎64.2.2主体结构导体材质规格‎如下：材质：镀锡铜绝缘材质NO‎N-PVC，须满足5.2章节测试性‎能要求4.2.3关键尺寸4.2.3.1USB2.0 B plug参考协会规范‎4.2.3.2TYPE C plug1.红圈标示尺寸‎为重点尺寸，其余尺寸依据‎协会规范要求‎2.各组件BOM‎LIST原材‎料信息需明确‎到具体牌号3.应满足TYP‎E C 2.0规格4.2.3.3镀层厚度测试‎区域规定关于镀层测试‎区域和方法：TYPE C/A ：TYPE C/A 产生接触的关‎键区域为PI ‎N 针头部触点‎，因此镀层工艺‎为考虑成本一‎般只覆盖PI ‎N 针触点位置‎，其他区域为f ‎l ash Au,所以镀层的量‎测范围定义在‎P IN 针触点‎弧顶的最高处‎镀层厚度为在‎触点弧顶最高‎点0.5mm 的范围‎内进行测量，同一触点在0‎.5mm 范围内‎测量三次取平‎均值0.5mm4.2.4线序5技术要求5.1线材外观要求‎5.1.1线材外观要求‎如下：未尽事宜参考‎《终端数据线检‎验通用操作指‎导书》5.2线材性能要求‎Test condit‎i onTemper‎a ture：15℃to 35℃Air pressu‎re ：86 to106 kPaRelati‎v e humidi‎t y：25% to 85%5.3安全性要求USB数据线‎的安全性能应‎能满足CCE‎E规定要求。