ASSR-302C-002E中文资料

EFC302门禁控制器2-8门联网门禁控制器EverAccess控制器带有键盘可进行系统管理控制，与PC机进行实时通迅,并具有反潜、门区互锁、多卡开门功能。

该控制器可单独使用也可联网使用，存储高达10W条事件记录。

具有LED指示灯，可方便连接键盘读卡器和细长型读卡器。

门模块组合2门控制器:EFC3024门控制器:EFC302+1×EFM-DR-1A=EFC3046门控制器:EFC302+2×EFM-DR-1A=EFC3068门控制器:EFC302+3×EFM-DR-1A=EFC308门+报警模块组合(报警输入/输出)2路输入/4路输出:EFC3028路输入/8路输出:EFM-AL-1A10路输入/14路输出: EFC302+1×EFM-DR-1A+EFM-AL-1A10路输入/16路输出: EFC302+2×EFM-DR-1A+EFM-AL-1A10路输入/18路输出: EFC302+3×EFM-DR-1A+EFM-AL-1A产品特点：∙Linux嵌入式操作系统，内置数据库引擎∙内置512M大容量存储器∙通过web浏览器远程设置、控制、管理，不需要另外安装任何软件∙通过内置多控制器门禁系统软件可管理31台Flex系列控制器∙SSL数据加密确保通过web浏览器安全访问∙支持网络和USB2.0自动备份、升级∙可连接2-8个读卡器，管理2-8门∙可管理10万张卡片∙支持100万条事件记录∙支持多达2048个门禁管制组和2048种门禁管制计划∙支持多达12种门禁模式∙支持4x4的锁定等级，最多实现4班组x4卡的多卡开门设置∙支持卡片特殊／管制组特殊的门禁模式∙每个门支持独立的10种日子设置（周日至周一和3种自定义日子），每个日子可以划分10个时段，最小单位1分钟∙支持有效期，密码，反潜，首卡等多种属性∙具有反潜、反胁迫、互锁等功能规格参数：操作系统Linux嵌入式基于WEB页面支持设置，监控和管理数据库内置处理器32-bit RISC CPU，200MHz存储器512MNAND Flash，64MDDR SDRAM通讯接口10/100MB以太网最大卡片数量10万最大事件记录100万支持读卡器数量2个(可扩展到8个)连接Flex系列控制器31台控制门数量2门(可扩展到8门)读卡器信号格式维根自适应或RS232卡片密码8 位系统密码8 位设/撤防密码8 位警报输入2-10路可扩展，每路可设为普通报警或火警警报输出2-18路可扩展网络接口100M以太网接口波特率9600 bps可编程时段每个日子可划分10个时段，最小单位1分钟可编程日期3种类型，可达到384种日期类型设置班组2048门区互锁支持多门互锁卡片有效期有反潜有键盘4×4备用电池接口支持多种门禁模式12种多卡开门支持4x4的锁定等级，最多实现4班组x4卡片的多卡开门设置LCD 显示屏带背光，2x9中文，2x18英/俄文实时时钟有蜂鸣器内置门继电器电流5A报警继电器电流2A电压DV12V±15%电流2A温度-10℃～+50℃尺寸300×216×33 mm （长×宽×高）。

• Packaged as 8 pin SOIC• Quick turn frequency programming allows samples in one to three days• Replaces nearly any crystal or oscillator • ICS300 produces up to 100 MHz at 3.3V, ICS301 produces up to 200 MHz at 3.3V ICS302 accepts up to 125 MHz clock input • Easy to cascade with ICS5xx series • Input crystal frequency of 5 - 27 MHz • Input clock frequency of 2 - 125 MHz • Low jitter - 50 ps one sigma• Compatible with all popular CPUs • Duty cycle of 45/55• Operating voltages of 3.0 to 5.5V• Full CMOS level outputs with 25mA drive capability at TTL levels• Tri-state output + PLL power down pin • Advanced, low power CMOS processThe ICS300 and ICS301 QTClocks™ generate a high quality, high frequency clock output and a reference from a low frequency crystal or clock input. They are designed to replace crystals and crystal oscillators in most electronic systems. The ICS302 can accept a higher frequency clock input to generate up to 200 MHz. The devices contain a One Time Programmable (OTP) ROM which is factory programmed with the PLL divider values to output a broad range of frequencies, from 6 to 200 MHz, allowing customer requests for different frequencies to be shipped in 1-3 days. UsingPhase-Locked-Loop (PLL) techniques, the devices run from a standard fundamental mode,inexpensive crystal, or clock. They are smaller and less expensive than one oscillator.Block DiagramDescriptionFeaturesCLKCrystal or clock inputREFPin AssignmentsX1/ICLKVDD GND REF X2PDTS DC CLKPin DescriptionsKey: I = Input, O = output, P = power supply connectionREF Clock OptionsExternal Components / Crystal SelectionThe ICS300/301/302 requires a 0.01µF decoupling capacitor to be connected between VDD and GND. It must be connected close to the ICS300/301/302 to minimize lead inductance. No external power supply filtering is required for this device. A 33Ω terminating resistor can be used next to the CLK and REF pins. The total on-chip capacitance is approximately 16 pF, so a parallel resonant, fundamental mode crystal should be used. For crystals with a specified load capacitance greater than 16 pF, crystal capacitors can be connected from each of the pins X1 and X2 to Ground. The value (in pF) of these crystal caps should be = (C L -16)*2, where C L is the crystal load capacitance in pF. These external capacitors are only required for applications where the exact frequency is critical. For a clock input, connect to X1/ICLK and leave X2 unconnected (no capacitors on either).Device ConfigurationThe specification is complete when the ICS300/301/302 QTClock Order Form accompanies this data sheet. The order form lists the input, REF, and CLK actual frequencies, as well as any other available options. This unique configuration is given a two character alphanumeric programming code, which must be specified when referring to samples.ICLK VDD GND REFPDTS DC CLKGNDElectrical SpecificationsWhile the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Inc. (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments.8 pin SOICOrdering InformationQTClock is a trademark of ICS xx represents a 2 character alphanumeric programming code assigned by the factory, which indicates the output frequencies on CLK and REF. All samples are shipped with an ICS300/301/302 order form describing the characteristics of the device.A1Package Outline and Package Dimensions(For current dimensional specifications, see JEDEC Publication No. 95.)。

Optoway TRS-3020G************************************************************************************************************************************************************************************************************************************************************************************************************************************************OPTOWAY TECHNOLOGY INC. No .38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303Tel: 886-3-5979798 Fax: 886-3-59797371TRS-3020G / TRS-3020TG / TRS-3020FG5V / 1310 nm / 155 Mbps RoHS Compliant Optical Single-Mode Transceiver************************************************************************************************************************************************************************FEATURESl Duplex SC Single Mode Transceiver: TRS-3020G l Duplex ST Single Mode Transceiver: TRS-3020TG l Duplex FC Single Mode Transceiver: TRS-3020FG l Distance up to 20 kml Industry Standard 1 x 9 Footprint l Single +5 V Power Supply l RoHS Compliant l 0 to 70o C Operatingl PECL Signal Detection Outputl LED Multisourced 1 x 9 Transceiver Interchangeable l Wave Solderable and Aqueous Washablel Class 1 Laser International Safety Standard IEC-60825 CompliantAPPLICATIONSl ATM 155 Mbps Linksl SONET/SDH Equipment Interconnect l Fast Ethernet 100 Mb/s LinksDESCRIPTIONThe TRS-3020G series single mode transceivers is low power, high performance module for bi-directional serial optical data communications such as SONET OC-3 / SDH STM-1 and Fast Ethernet. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry.LASER SAFETYThis single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.ORDER INFORMATIONP/No. Bit Rate (Mb/s) SONET/SDH Distance (km) Wavelength (nm) Voltage(V) PackageTemp.(o C)TX Power (dBm) RX Sens. (dBm) RoHS Compliant TRS-3020G15520131051X9 SC/ST/FC 0 to 70-7 to -18 -32 YAbsolute Maximum RatingsParameterSymbol Min Max Units NotesStorage Temperature Tstg -40 85 o COperating Temperature Topr 0 70 o C TRS-3020GSoldering Temperature --- 260 o C 10 seconds on leads only Power Supply Voltage Vcc 0 6 V Input Voltage --- GND Vcc V Output CurrentIout30mARecommended Operating ConditionsParameterSymbol Min Typ Max Units Power Supply Voltage Vcc 4.75 5 5.25 V Operating Temperature Topr 0 70 oC / TRS-3020GData Rate155 Mb/s Power Supply CurrentIcc240mATransmitter Specifications (0o C < Topr < 70o C, 4.75V < Vcc < 5.25V)Parameter Symbol Min Typ Max Units NotesOpticalOptical Transmit Power Po -18 --- -7 dBm 1Output Center Wavelength λ1261 1310 1360 nmOutput Spectrum Width ∆λ--- --- 7.7 nm RMS (σ)Extinction Ratio E R8.2 --- --- dBOutput Eye Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957Optical Rise Time t r 2 ns 10% to 90% Values Optical Fall Time t f 2 ns 10% to 90% Values Relative Intensity Noise RIN -116 dB/HzTotal Jitter TJ 1 ns 2ElectricalData Input Current – Low I IL-350 µAData Input Current – High I IH350 µADifferential Input Voltage V IH - V IL300 mVData Input Voltage – Low V IL - V CC-2.0 -1.58 V 3Data Input Voltage -- High V IH - V CC-1.1 -0.74 V 3Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber.2. Measured with a 223-1 PRBS with 72 ones and 72 zeros.3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs.Receiver Specifications(0o C < Topr < 70o C, 4.75 V < Vcc < 5.25V)Parameter Symbol Min Typ Max Units NotesOpticalSensitivity--- --- --- -32 dBm 1 Maximum Input Power Pin -3 --- dBmSignal Detect -- Asserted Pa --- --- -32 dBm Transition: low to high Signal Detect -- Deasserted Pd -47 --- --- dBm Transition: high to low Signal detect -- Hysteresis 1.0 --- 4.0 dBWavelength of Operation 1100 --- 1600 nmElectricalData Output Voltage – Low V OL - V CC-2.0 -1.58 V 2Data Output Voltage – High V OH - V CC-1.1 -0.74 V 2Signal Detect Output Voltage -- Low V OL - V CC-2.0 -1.58 VSignal Detect Output Voltage -- High V OH - V CC-1.1 -0.74 VNotes: 1. Minimum sensitivity and saturation levels at BER=1E-10 for a 223-1 PRBS with 72 ones and 72 zeros.2. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs.*********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303Tel: 886-3-5979798 Fax: 886-3-5979737CONNECTION DIAGRAMReceiver Signal Ground 1 (Rx GND)Receiver Data Out 2 (RD+) N/CReceiver Data Out Bar 3 (RD−)Signal Detect 4 (SD)Receiver Power Supply 5 (Rx Vcc) TOP VIEWTransmitter Power Supply 6 (Tx Vcc)Transmitter Data In Bar 7 (TD−)Transmitter Data In 8 (TD+) N/CTransmitter Signal Ground 9 (Tx GND)OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737*********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303Tel: 886-3-5979798 Fax: 886-3-5979737。

“水护卫”HG – 302 游泳池水质监控仪技师手册操作和维修保养指南蓝典科技有限公司目录第1章前言 31.1 拟定用途 31.2 安全注意事项 31.3 各章综述 4 第2章综述 52.1 水池化学综述 52.2 水护卫解决方案 52.3 特点和模块 52.3.1 标准模块 52.3.2 可选模块 62.3.3 远程读数和控制 62.4 系统部件7 第3章安装93.1 选择位置93.2 场地要求和安装93.2.1 机械安装要求93.2.2 机械安装93.3 管路要求和安装113.3.1 管路连接113.4 电力要求和安装123.4.1 连接电力电源123.4.2 连接相关电源123.5 与配制系统间的连线13 第4章首次操作和校准144.1 安装传感器144.2 安装试剂154.3 首次菜单设置174.3.1 水护卫控制面板174.3.2 液晶显示194.3.3 菜单194.3.4 配置设置214.4 校准234.4.1 氯含量校准234.4.2 pH值校准244.4.3 氧化还原剂校准264.4.4 温度校准274.5 技师菜单设置284.6 校准和初始操作检验单30 第5章常规运行和维护325.1 监视水护卫报警335.2 更换试剂345.3 清洁过滤器355.4 故障排除365.4.1 无流量375.4.2 无试剂375.4.3 单元不干净385.4.4 氯含量<0.1 395.4.5 更换灯光405.5 更换部件415.5.1 更换传感器415.5.2 更换流量开关425.5.3 更换试剂虹吸管435.5.4 更换试剂泵435.5.5 更换比色计模块435.5.6 更换比色计电磁阀445.5.7 更换控制面板模块455.5.8 更换I/O模块465.5.9 更换pH值、氧化还原剂和温度模块465.5.10 更换比色模块465.5.11 模块软件升级46 第6章附录A：继电器、菜单和报警476.1 继电器476.2 操作员菜单486.3 技师菜单496.4 报警506.5 技术规格51 第7章附录B：设置比例控制及举例说明547.1 比例控制综述547.2 设置比例因数557.3 设置泵的周期577.4 逐步比例设定577.5 氯含量首次平均设定值597.6 pH首次平均设定值59 第8章其它事项60 第9章HG-302的订购代码61 第10章备件62第1章：前言1.1拟定用途本手册为安装和保养“水护卫”HG-302水质控制器的技师而配备。