zemax常用评价函数操作数

Operand Definitions ZEMAX supports optimization operands which are used to define the merit function. Each operand may be assigned a weight which indicates the relative importance of that operand, as well as a target, which is the desired value for that operand. The operands are listed below.

ABSO: Absolute value 绝对值 ACOS: Arccosine AMAG: Angular magnification 角放大率 ANAR: Angular aberration ASIN: Arcsine ASTI: Astigmatism 初级像散 ATAN: Arctangent AXCL: Axial color BLNK: Blank BSER: Boresight Error COGT: Conic greater than COLT: Conic less than COMA: Coma 初级彗差 CONF: Configuration # CONS: Constant 常量 COSI: Cosine COVA: Conic value CTGT: Center thickness greater than 中心厚度(间隔)大于 CTLT: Center thickness less than 中心厚度(间隔)小于 CTVA: Center thickness value 中心厚度(间隔)等于 CVGT: Curvature greater than 曲率大于 CVLT: Curvature less than 曲率小于 CVOL: Cylinder volume CVVA: Curvature value 曲率等于 DENC: Diffraction encircled energy DENF: Diffraction encircled energy fraction DIFF: Difference DIMX: Distortion max 最大畸变 DISC: Distortion calibrated DISG: Generalized distortion DIST: Distortion 畸变 DIVI: Division DLTN: Delta N DMFS: Default merit function start 默认评价函数起始点 DMGT: Diameter greater than 直径大于 DMLT: Diameter less than 直径小于 DMVA: Diameter value 直径值 DXDX: Derivative Dx/Dx DXDY: Derivative Dx/Dy DYDX: Derivative Dy/Dx DYDY: Derivative Dy/Dy EFFL: Effective focal length 有效焦距 EFLX: Effective focal length x x方向焦距 EFLY: Effective focal length y y方向焦距 ENDX: End execution ENPP: Entrance pupil position 入瞳位置 EPDI: Entrance pupil diameter 入瞳直径 EQUA: Equal ETGT: Edge thickness greater than 边缘厚度大于 ETLT: Edge thickness less than 边缘厚度小于 ETVA: Edge thickness value 边缘厚度等于 EXPP: Exit pupil position 出瞳位置 FCGS: Field curvature, generalized, sagittal FCGT: Field curvature, generalized, tangential FCUR: Field curvature 场曲 FICL: Fiber coupling efficiency FOUC: Foucault analysis GBW0: Gaussian beam waist 0 GBWA: Gaussian beam size GBWD: Gaussian beam divergence GBWZ: Gaussian beam z position GBWR: Gaussian beam phase radius GCOS: Glass relative cost GENC: Geometric encircled energy GLCA: Global coordinate x normal GLCB: Global coordinate y normal GLCC: Global coordinate z normal GLCX: Global coordinate x coordinate GLCY: Global coordinate y coordinate GLCZ: Global coordinate z coordinate GMTA: Geometric MTF average 几何平均MTF GMTS: Geometric MTF sagittal 几何弧矢MTF GMTT: Geometric MTF tangential几何子午MTF GPIM: Ghost Pupil Image GRMN: Gradient minimum index GRMX: Gradient maximum index GTCE: Glass Thermal Coefficient of Expansion HHCN: Tests for hyper-hemisphere conditions IMAE: Image analysis efficiency INDX: Index of refraction InGT: Index greater than折射率大于 InLT: Index less than 折射率小于 InVA: Index value 折射率等于 ISFN: Image space F/# 像方F数 LACL: Lateral color LINV: Lagrange invariant LPTD: LightPath Delta MAXX: Maximum MCOG: Multi-configuration operand greater than MCOL: Multi-configuration operand less than MCOV: Multi-configuration operand value MINN: Minimum MNAB: Minimum Abbe 最小阿贝数 MNCA: Minimum center thickness air最小中心间隔（空气） MNCG: Minimum center thickness glass最小中心厚度（玻璃） MNCT: Minimum center thickness 最小中心厚度（间隔） MNCV: Minimum curvature 最小曲率半径 MNDT: Minimum diameter to thickness ratio最小通光直径与厚度之比 MNEA: Minimum edge thickness air最小边缘间隔（空气） MNEG: Minimum edge thickness glass最小边缘厚度（玻璃 MNET: Minimum edge thickness最小边缘厚度（间隔） MNIN: Minimum index最小折射率 MNPD: Minimum partial dispersion MNSD: Minimum semi-diameter MSWA: MTF square wave average MSWS: MTF square wave sagittal MSWT MTF square wave tangential MTFA: MTF average 平均MTF MTFS: MTF sagittal 弧矢MTF MTFT: MTF tangential 子午MTF MXAB: Maximum Abbe 最大阿贝数 MXCA: Maximum center thickness air 最大中心间隔（空气） MXCG: Maximum center thickness glass最大中心厚度（玻璃） MXCT: Maximum center thickness 最大中心厚度（间隔） MXCV: Maximum curvature 最大曲率半径 MXDT: Maximum diameter to thickness ratio最大通光直径与厚度之比 MXEA: Maximum edge thickness air 最大边缘间隔（空气） MXEG: Maximum edge thickness glass 最大边缘厚度（玻璃） MXET: Maximum edge thickness 最大边缘厚度（间隔） MXIN: Maximum index 最大折射率 MXPD: Maximum partial dispersion MXSD: Maximum semi-diameter 最大半口径 NPXG: Non-sequential object position x greater than NPXL: Non-sequential object position x less than NPXV: Non-sequential object position x value NPYG: Non-sequential object position y greater than NPYL: Non-sequential object position y less than NPYV: Non-sequential object position y value NPZG: Non-sequential object position z greater than