MAX4359EWG-T中文资料

________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at .
Applications
2-Cell Battery-Operated Systems Portable Electronic Equipment Battery-Powered Instrumentation Digital Scales Strain Gauges Sensor Amplifiers Cellular Phones
Pin Configurations continued at end of data sheet.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. UCSP is a trademark of Maxim Integrated Products, Inc. 1
ELECTRICAL CHARACTERISTICS
(VCC = 1.8V to 5.5V, VEE = VCM = 0, VOUT = VCC/2, RL = 100kΩ connected to VCC/2, TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER Supply Voltage Range Quiescent Supply Current (Per Amplifier) Input Offset Voltage Input Bias Current Input Offset Current Differential Input Resistance Input Common-Mode Voltage Range SYMBOL VCC IQ VOS IB IOS RIN VCM VCC = 1.8V VCC = 5.0V MAX4291 MAX4292/MAX4294 VCC = 5.0V, 0 ≤ VCM ≤ 5.0V VCC = 5.0V, 0 ≤ VCM ≤ 5.0V |VIN+ - VIN-| < 10mV Inferred from CMRR test Tested for 0 ≤ VCM ≤ 1.8V; VCC = 1.8V Common-Mode Rejection Ratio Common-Mode Rejection Ratio CMRR Tested for 0 ≤ VCM ≤ 5.0V, VCC = 5.0V PSRR MAX4291 MAX4292/MAX4294 60 66 77 90 dB 90 100 dB MAX4291 MAX4292/MAX4294 0 50 57 80 dB 80 CONDITIONS Inferred from PSRR test MIN 1.8 100 100 ±400 ±200 ±15 ±1 0.75 VCC TYP MAX 5.5 210 255 ±2500 ±1200 ±60 ±7 UNITS V µA µV nA nA MΩ V

General DescriptionThe MAX4758/MAX4759 quad double-pole/double-throw (DPDT) analog switches operate from a single +1.8V to +5.5V supply. These switches feature low 0.5Ωon-resistance for audio switching and a low 25pF capacitance for data switching.The MAX4758 has eight 0.5Ωon-resistance switches to switch audio signals. The MAX4759 has four 0.5Ωon-resistance switches to route audio signals and four 25pF capacitance switches to route data signals. The MAX4758/MAX4759 have four logic inputs to control the switches in pairs.The MAX4758/MAX4759 are available in a small 36-pin (6mm x 6mm) thin QFN and 36-bump (3mm x 3mm)chip-scale package (UCSP™).ApplicationsFeatures♦Data and Audio Signal Routing♦Low On-Resistance (0.5Ω) Audio Switches ♦0.2ΩOn-Resistance Flatness♦0.1ΩChannel-to-Channel Matching♦Low-Capacitance (25pF) Data Switches (MAX4759)♦0.2ns Skew (MAX4759)♦0.03% THD♦+1.8V to +5.5V Supply Range ♦Rail-to-Rail Signal Handling♦Tiny 36-Bump UCSP (3mm x 3mm)♦36-Pin Thin QFN (6mm x 6mm)MAX4758/MAX4759Quad DPDT Audio/Data Switches in UCSP/QFN________________________________________________________________Maxim Integrated Products1Ordering Information19-3043; Rev 2; 2/05For pricing, delivery, and ordering information,please contact Maxim/Dallas Direct!at 1-888-629-4642, or visit Maxim’s website at .UCSP is a trademark of Maxim Integrated Products, Inc.Functional DiagramsPin Configurations/Truth Table appear at end of data sheet.Speaker-HeadsetSwitchingAudio-Signal Routing Cellular PhonesPDAs/Hand-Held DevicesNotebook Computers USB Signal SwitchingM A X 4758/M A X 4759Quad DPDT Audio/Data Switches in UCSP/QFNABSOLUTE MAXIMUM RATINGSELECTRICAL CHARACTERISTICS(V+ = +2.7V to +5.25V, T A = -40°C to +85°C, unless otherwise noted. Typical values are at V+ = 3V, T A = +25°C.) (Notes 2, 3)Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.(All voltages referenced to GND.)V+, IN_......................................................................-0.3V to +6V COM_, NO_, NC_ (Note 1)...........................-0.3V to (V+ + 0.3V)Continuous CurrentNO_, NC_, COM_ (MAX4758)....................................±300mA NO1–NO4, NC1–NC4, COM1–COM4 (MAX4759).....±300mA NO5–NO8, NC5–NC8 COM5–COM8 (MAX4759)......±100mA Peak Current NO_, NC_, COM_ (MAX4758)NO1–NO4, NC1–NC4, COM1–COM4 (MAX4759)(pulsed at 1ms, 10% duty cycle)................................±500mA (pulsed at 1ms, 50% duty cycle)................................±400mA Peak Current NO5–NO8, NC5–NC8, COM5–COM8 (MAX4759)(pulsed at 1ms, 10% duty cycle)................................±200mA (pulsed at 1ms, 50% duty cycle)...............................±300mAContinuous Power Dissipation (T A = +70°C)36-Bump UCSP (derate 15.3mW/°C above +70°C)....1221mW 36-Pin Thin QFN (derate 26.3mW/°C above +70°C)...2105mW ESD per Method 3015.7.......................................................±2kV Operating Temperature Range ...........................-40°C to +85°C Junction Temperature......................................................+150°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10s)................................+300°C Bump Temperature (soldering)Infrared (15s)...............................................................+220°C Vapor Phase (60s).......................................................+215°CNote 1:Signals on NO_, NC_, COM_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to maximumcurrent rating.MAX4758/MAX4759Quad DPDT Audio/Data Switches in UCSP/QFN_______________________________________________________________________________________3ELECTRICAL CHARACTERISTICS (continued)M A X 4758/M A X 4759Quad DPDT Audio/Data Switches in UCSP/QFN 4_______________________________________________________________________________________Typical Operating Characteristics(V+ = 3V, T A = +25°C, unless otherwise noted.)design. Thin QFN parts are 100% tested at +85°C and limits across the full temperature range are guaranteed by correla-tion and design.Note 4:R ON and ΔR ON matching specifications are guaranteed by design.Note 5:ΔR ON = R ON(MAX)- R ON(MIN).Note 6:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over thespecified analog signal ranges.Note 7:Guaranteed by design, not production tested.Note 8:Off-isolation = 20log 10[V COM_/ (V NO_ or V NC_)], V COM_= output, V NO_or V NC_= input to off switch.Note 9:Between any two switches.ELECTRICAL CHARACTERISTICS (continued)(V+ = +2.7V to +5.25V, T A = -40°C to +85°C, unless otherwise noted. Typical values are at V+ = 3V, T A = +25°C.) (Notes 2, 3)ON-RESISTANCE vs. V COMV COM (V)R O N (Ω)4.54.03.53.02.52.01.51.00.50.51.01.52.02.5005.0ON-RESISTANCEvs. V COM AND TEMPERATUREV COM (V)R O N (Ω)2.52.01.51.00.50.20.40.60.81.01.21.41.61.82.0003.0ON-RESISTANCEvs. V COM AND TEMPERATUREV COM (V)R O N (Ω)4.54.03.0 3.51.0 1.5 2.0 2.50.50.20.40.60.81.01.21.41.61.82.05.0MAX4758/MAX4759Quad DPDT Audio/Data Switches in UCSP/QFN_______________________________________________________________________________________5ON-RESISTANCE vs. V COMV COM (V)R O N (Ω)4.54.03.0 3.51.0 1.5 2.0 2.50.52345678910105.0ON-RESISTANCEvs. V COM AND TEMPERATUREV COM (V)R O N (Ω)2.52.01.51.00.512345003.0ON-RESISTANCEvs. V COM AND TEMPERATUREV COM (V)R O N (Ω)4.54.03.53.02.52.01.51.00.5123455.0NO/NC OFF-LEAKAGE CURRENTvs. TEMPERATURETEMPERATURE (°C)N O /N C O F F -L E A K A G E C U R R E N T (n A )603510-150.010.11100.001-4085COM ON-LEAKAGE CURRENTvs. TEMPERATURETEMPERATURE (°C)C O M O N -L E A K A G E C U R R E N T (n A )603510-150.010.11100.001-4085CHARGE INJECTION vs. V COMV COM (V)C H A R G E I N J E C T I O N (p C )431220406080100120140160005CHARGE INJECTION vs. V COMV COM (V)C H A R G E I N J E C T I O N (p C )4321102030405060005SUPPLY CURRENT vs. SUPPLY VOLTAGEM A X 4758 t o c 11SUPPLY VOLTAGE (V)S U P P L Y C U R R E N T (n A )5.55.02.0 2.5 3.0 4.03.5 4.50.51.01.52.02.53.03.54.01.5 6.0Typical Operating Characteristics (continued)(V+ = 3V, T A = +25°C, unless otherwise noted.)M A X 4758/M A X 4759Quad DPDT Audio/Data Switches in UCSP/QFN 6_______________________________________________________________________________________Typical Operating Characteristics (continued)(V+ = 3V, T A = +25°C, unless otherwise noted.)LOGIC THRESHOLD vs. SUPPLY VOLTAGEM A X 4758 t o c 13SUPPLY VOLTAGE (V)L O G I C T H R E S H O L D (V )5.04.54.03.53.02.52.00.40.81.21.62.001.55.5V IHV ILTURN-ON/OFF TIMES vs. SUPPLY VOLTAGESUPPLY VOLTAGE (V)t O N /t O F F (n s )5.04.52.02.53.03.54.0102030405060708001.55.5TURN-ON/OFF TIMES vs. SUPPLY VOLTAGESUPPLY VOLTAGE (V)t O N /t O F F (n s )5.04.52.02.53.03.54.0102030405060708001.55.5TURN-ON/OFF TIMES vs. TEMPERATURETEMPERATURE (°C)t O N /t O F F (n s )603510-151020304050600-4085TURN-ON/OFF TIMES vs. TEMPERATURETEMPERATURE (°C)t O N /t O F F (n s )603510-1510203040506070-4085SUPPLY CURRENT vs. TEMPERATURETEMPERATURE (°C)S U P P L Y C U R R E N T (n A )603510-150.11010000.001-4085MAX4758/MAX4759Quad DPDT Audio/Data Switches in UCSP/QFN_______________________________________________________________________________________7SKEW vs. SUPPLY VOLTAGESUPPLY VOLTAGE (V)S K E W (p s )5.04.54.03.53.02.52.010020030040050060001.55.5SKEW vs. TEMPERATURETEMPERATURE (°C)S K E W (p s )603510-151002003004005006000-4085FREQUENCY RESPONSEFREQUENCY (MHz)O N -L O S S (d B )1000.011-120-100-80-60-40-20020-1400.0001FREQUENCY RESPONSEFREQUENCY (MHz)O N -L O S S (d B )1000.011-120-100-80-60-40-20020-1400.0001TOTAL HARMONIC DISTORTIONvs. FREQUENCYFREQUENCY (Hz)T HD (%)10k1k 1000.010.110.00110100kTOTAL HARMONIC DISTORTIONvs. FREQUENCYFREQUENCY (Hz)T H D (%)10k1k 1000.110100k10.01Typical Operating Characteristics (continued)(V+ = 3V, T A = +25°C, unless otherwise noted.)M A X 4758/M A X 4759Quad DPDT Audio/Data Switches in UCSP/QFN 8_______________________________________________________________________________________MAX4758/MAX4759Quad DPDT Audio/Data Switches in UCSP/QFN_______________________________________________________________________________________9Detailed DescriptionThe MAX4758/MAX4759 quad DPDT analog switches operate from a single +1.8V to +5.5V supply. These devices are fully specified for +3V applications.The MAX4758/MAX4759 (switches 1–4) have a guaran-teed 0.5Ωon-resistance, making them ideal for audio switching applications. The MAX4759 also includes four single-pole/double-throw (SPDT) switches (switches 5–8) that have a guaranteed 0.2Ωon-resistance, a low 25pF capacitance, 0.2ns change in skew making them ideal for either data or audio switching applications.These switches have four logic inputs to control two switches in pairs.Applications InformationDigital Control InputsThe MAX4758/MAX4759 logic inputs accept up to +5.5V regardless of the supply voltage. For example,with a +3.3V supply, IN_ can be driven low to GND and high to +5.5V, which allows mixed logic levels in a sys-tem. Driving the control logic inputs rail-to-rail also mini-mizes power consumption. For a +3V supply voltage,the logic thresholds are 0.5V (low) and 1.4V (high).Analog Signal LevelsAnalog signal inputs over the full voltage range (0V to V+)are passed through the switch with minimal change in on-resistance (see the Typical Operating Characteristics ).The switches are bidirectional so NO_, NC_, and COM_can be either inputs or outputs.Power-Supply BypassingPower-supply bypassing improves noise margin and prevents switching noise from propagating from the V+supply to other components. A 0.1µF capacitor connect-ed from V+ to GND is adequate for most applications.Power-Supply SequencingCMOS devices require proper power-supply sequenc-ing. Always apply V+ before the analog signals, espe-cially if the input signal is not current limited. If sequencing is not possible, and the input signal is not current limited to less than 20mA, add a small-signal diode (Figure 1). Adding the diode reduces the analog range to a diode drop (0.7V) below V+ and increases the on-resistance slightly. The maximum supply voltage must not exceed +6V at any time.UCSP Applications InformationFor the latest application details on UCSP construction,dimensions, tape carrier information, PCB techniques,bump-pad layout, and recommended reflow tempera-ture profile, as well as the latest information on reliability testing results, go to the Maxim website at /ucsp for the Application Note, “UCSP—A Wafer-Level Chip-Scale Package”.Figure 1. Overvoltage Protection Using an External Blocking DiodeM A X 4758/M A X 4759Quad DPDT Audio/Data Switches in UCSP/QFN 10______________________________________________________________________________________Timing Circuits/Timing DiagramsFigure 2. Switching TimeFigure 3. Break-Before-Make IntervalMAX4758/MAX4759______________________________________________________________________________________11Timing Circuits/Timing Diagrams (continued)Figure 4. Input/Output Skew Timing DiagramFigure 5. Charge InjectionM A X 4758/M A X 475912______________________________________________________________________________________Figure 6. On-Loss, Off-Isolation, and CrosstalkTiming Circuits/Timing Diagrams (continued)Figure 7. Channel On-/Off-CapacitanceTypical Operating CircuitMAX4758/MAX4759______________________________________________________________________________________13Pin Configurations/Truth TablesChip InformationTRANSISTOR COUNT: 1432 PROCESS: CMOSM A X 4758/M A X 475914______________________________________________________________________________________Package Information(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to /packages .)MAX4758/MAX4759 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses areimplied. Maxim reserves the right to change the circuitry and specifications without notice at any time.Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________15©2005 Maxim Integrated Productsis a registered trademark of Maxim Integrated Products, Inc. Package Information (continued)(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to /packages.)Revision HistoryPages changed at Rev 2: 1, 3, 4, 9, 15。

MAX809 Series,MAX810 SeriesVery Low Supply Current3−Pin MicroprocessorReset MonitorsThe MAX809 and MAX810 are cost−effective system supervisor circuits designed to monitor V CC in digital systems and provide a reset signal to the host processor when necessary. No external components are required.The reset output is driven active within 10 m sec of V CC falling through the reset voltage threshold. Reset is maintained active for a timeout period which is trimmed by the factory after V CC rises above the reset threshold. The MAX810 has an active−high RESET output while the MAX809 has an active−low RESET output. Both devices are available in SOT−23 and SC−70 packages.The MAX809/810 are optimized to reject fast transient glitches on the V CC line. Low supply current of 0.5 m A (V CC= 3.2 V) makes these devices suitable for battery powered applications.Features•Precision V CC Monitor for 1.5 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies•Precision Monitoring V oltages from 1.2 V to 4.9 V Availablein 100 mV Steps•Four Guaranteed Minimum Power−On Reset Pulse Width Available (1 ms, 20 ms, 100 ms, and 140 ms)•RESET Output Guaranteed to V CC = 1.0 V.•Low Supply Current•Compatible with Hot Plug Applications•V CC Transient Immunity•No External Components•Wide Operating Temperature: −40°C to 105°C•Pb−Free Packages are AvailableTypical Applications•Computers•Embedded Systems•Battery Powered Equipment•Critical Microprocessor Power Supply MonitoringV CCFigure 1. Typical Application DiagramSee general marking information in the device marking section on page 8 of this data sheet.DEVICE MARKING INFORMATIONSee detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet.ORDERING INFORMATIONPIN DESCRIPTIONPin No.Symbol Description1GND Ground2RESET (MAX809)RESET output remains low while V CC is below the reset voltage threshold, and for a reset timeoutperiod after V CC rises above reset threshold2RESET (MAX810)RESET output remains high while V CC is below the reset voltage threshold, and for a reset timeoutperiod after V CC rises above reset threshold3V CC Supply Voltage (Typ)ABSOLUTE MAXIMUM RATINGSRating Symbol Value Unit Power Supply Voltage (V CC to GND)V CC−0.3 to 6.0V RESET Output Voltage (CMOS)−0.3 to (V CC + 0.3)V Input Current, V CC20mA Output Current, RESET20mAdV/dt (V CC)100V/m secThermal Resistance, Junction−to−Air (Note 1)SOT−23SC−70R q JA301314°C/WOperating Junction Temperature Range T J−40 to +105°C Storage Temperature Range T stg−65 to +150°C Lead Temperature (Soldering, 10 Seconds)T sol+260°C ESD ProtectionHuman Body Model (HBM): Following Specification JESD22−A114 Machine Model (MM): Following Specification JESD22−A1152000200VLatchup Current Maximum Rating: Following Specification JESD78 Class IIPositiveNegative I Latchup200200mAStresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.1.This based on a 35x35x1.6mm FR4 PCB with 10mm2 of 1 oz copper traces under natural convention conditions and a single componentcharacterization.2.The maximum package power dissipation limit must not be exceeded.P D+T J(max)*T Aq JAwith T J(max) = 150°CELECTRICAL CHARACTERISTICS T A = −40°C to +105°C unless otherwise noted. Typical values are at T A = +25°C. (Note 3) Characteristic Symbol Min Typ Max Unit V CC RangeT A = 0°C to +70°CT A = −40°C to +105°C 1.01.2−−5.55.5VSupply CurrentV CC = 3.3 VT A = −40°C to +85°CT A = 85°C to +105°C V CC = 5.5 VT A = −40°C to +85°CT A = 85°C to +105°C I CC−−−−0.5−0.8−1.22.01.82.5m AReset Threshold (V in Decreasing) (Note 4)V TH V MAX809SN490T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 4.834.784.664.9−−4.975.025.14MAX8xxLTR, MAX8xxSQ463T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 4.564.504.404.63−−4.704.754.86MAX809HTRT A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 4.484.434.324.55 4.624.674.78MAX8xxMTR, MAX8xxSQ438T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 4.314.274.164.38 4.454.494.60MAX809JTR, MAX8xxSQ400T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 3.943.903.804.00−−4.064.104.20MAX8xxTTR, MAX809SQ308T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 3.043.002.923.08−−3.113.163.24MAX8xxSTR, MAX8xxSQ293T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 2.892.852.782.93−−2.963.003.08MAX8xxRTR, MAX8xxSQ263T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 2.592.562.492.63−−2.662.702.77MAX809SN232, MAX809SQ232T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 2.282.252.212.32−−2.352.382.45MAX809SN160T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 1.581.561.521.60−−1.621.641.68MAX809SN120, MAX8xxSQ120T A = +25°CT A = −40°C to +85°C T A = +85°C to +105°C 1.181.171.141.20−−1.221.231.263.Production testing done at T A = 25°C, over temperature limits guaranteed by design.4.Contact your ON Semiconductor sales representative for other threshold voltage options.ELECTRICAL CHARACTERISTICS(continued) T A = −40°C to +105°C unless otherwise noted. Typical values are atT A = +25°C. (Note 5)Characteristic Symbol Min Typ Max Unit Detector Voltage Threshold Temperature Coefficient−30−ppm/°C V CC to Reset Delay V CC = V TH to (V TH − 100 mV)−10−m secReset Active TimeOut Period (Note 6) MAX8xxSN(Q)293D1MAX8xxSN(Q)293D2MAX8xxSN(Q)293D3MAX8xxSN(Q)293t RP1.020100140−−−−3.366330460msecRESET Output Voltage Low (No Load) (MAX809)V CC = V TH − 0.2 V1.6 V v V TH v2.0 V, I SINK = 0.5 mA2.1 V v V TH v 4.0 V, I SINK = 1.2 mA4.1 V v V TH v 4.9 V, I SINK = 3.2 mAV OL−−0.3VRESET Output Voltage High (No Load) (MAX809)V CC = V TH + 0.2 V1.6 V v V TH v2.4 V, I SOURCE = 200 m A2.5 V v V TH v 4.9 V, I SOURCE = 500 m AV OH0.8 V CC−−VRESET Output Voltage High (No Load) (MAX810)V CC = V TH + 0.2 V1.6 V v V TH v2.4 V, I SOURCE = 200 m A2.5 V v V TH v 4.9 V, I SOURCE = 500 m AV OH0.8 V CC−−VRESET Output Voltage Low (No Load) (MAX810)V CC = V TH − 0.2 V1.6 V v V TH v2.0 V, I SINK = 0.5 mA2.1 V v V TH v 4.0 V, I SINK = 1.2 mA4.1 V v V TH v 4.9 V, I SINK = 3.2 mAV OL−−0.3V5.Production testing done at T A = 25°C, over temperature limits guaranteed by design.6.Contact your ON Semiconductor sales representative for timeout options availability for other threshold voltage options.TYPICAL OPERATING CHARACTERISTICS0.50.40.30.20.10S U P P L Y C U R R E N T (m A )0.60.250.150.0500.35S U P P L Y C U R R E N T (m A )−50−2502550TEMPERATURE (°C)S U P P L Y C U R R E N T (m A )75100−50−2502550TEMPERATURE (°C)100Figure 6. Supply Current vs. Temperature(No Load, MAX809)Figure 7. Supply Current vs. Temperature (NoLoad, MAX810)750.100.200.30TYPICAL OPERATING CHARACTERISTICS252015105.00−50−25255075TEMPERATURE (°C)O U T P U T V O L T A G E V C C (m V )30100250−50−252575125TEMPERATURE (°C)125P O W E R −D O W N R E S E T D E L A Y (m s e c )125−50−2502550TEMPERATURE (°C)N O R M A L I Z E D P O W E R −U P R E S E T T I M E O U T0.70.80.91.21.375100Figure 10. Power−Down Reset Delay vs.Temperature and Overdrive (V TH = 1.2 V)Figure 11. Power−Down Reset Delay vs.Temperature and Overdrive (V TH = 4.9 V)Figure 12. Normalized Power−Up Reset vs.Temperature10050751.01.110050APPLICATIONS INFORMATIONV CC Transient RejectionThe MAX809 provides accurate V CC monitoring and reset timing during power−up, power−down, and brownout/sag conditions, and rejects negative−going transients (glitches) on the power supply line. Figure 13shows the maximum transient duration vs. maximum negative excursion (overdrive) for glitch rejection. Any combination of duration and overdrive which lies under the curve will not generate a reset signal. Combinations above the curve are detected as a brownout or power−down.Typically, transient that goes 100 mV below the reset threshold and lasts 5.0 m s or less will not cause a reset pulse.Transient immunity can be improved by adding a capacitor in close proximity to the V CC pin of the MAX809.Figure 13. Maximum Transient Duration vs.Overdrive for Glitch Rejection at 25°CV CC1011060M A X I M U M T R A N S I E N T D U R A T I O N (m s e c )RESET COMPARATOR OVERDRIVE (mV)410160210260310360RESET Signal Integrity During Power−DownThe MAX809 RESET output is valid to V CC = 1.0 V .Below this voltage the output becomes an “open circuit” and does not sink current. This means CMOS logic inputs to the Microprocessor will be floating at an undetermined voltage.Most digital systems are completely shutdown well above this voltage. However, in situations where RESET must bemaintained valid to V CC = 0 V , a pull−down resistor must be connected from RESET to ground to discharge stray capacitances and hold the output low (Figure 14). This resistor value, though not critical, should be chosen such that it does not appreciably load RESET under normal operation (100 k W will be suitable for most applications).Figure 14. Ensuring RESET Valid to V CC = 0 VProcessors With Bidirectional I/O PinsSome Microprocessor’s have bidirectional reset pins.Depending on the current drive capability of the processor pin, an indeterminate logic level may result if there is a logic conflict. This can be avoided by adding a 4.7 k W resistor in series with the output of the MAX809 (Figure 15). If there are other components in the system which require a reset signal, they should be buffered so as not to load the reset line.If the other components are required to follow the reset I/O of the Microprocessor, the buffer should be connected as shown with the solid line.Figure 15. Interfacing to Bidirectional Reset I/OBUFFERED RESETORDERING, MARKING AND THRESHOLD INFORMATIONPart Number V TH*(V)Timeout*(ms)Description Marking Package Shipping†MAX809SN160T1 1.60140−460Push−Pull RESET SAA SOT23−33000 / Tape & ReelMAX809SN160T1G 1.60140−460SAA SOT23−3(Pb−Free)MAX809SN232T1 2.32140−460SQP SOT23−3MAX809SN232T1G 2.32140−460SQP SOT23−3(Pb−Free)MAX809RTR 2.63140−460SPS SOT23−3MAX809RTRG 2.63140−460SPS SOT23−3(Pb−Free)MAX809STR 2.93140−460SPT SOT23−3MAX809STRG 2.93140−460SPT SOT23−3(Pb−Free)MAX809TTR 3.08140−460SPU SOT23−3MAX809TTRG 3.08140−460SPU SOT23−3(Pb−Free)MAX809JTR 4.00140−460SPR SOT23−3MAX809JTRG 4.00140−460SPR SOT23−3(Pb−Free)MAX809MTR 4.38140−460SPV SOT23−3MAX809MTRG 4.38140−460SPV SOT23−3(Pb−Free)MAX809HTR 4.55140−460SBD SOT23−3MAX809HTRG 4.55140−460SBD SOT23−3(Pb−Free)MAX809LTR 4.63140−460SPW SOT23−3MAX809LTRG 4.63140−460SPW SOT23−3(Pb−Free)MAX809SN490T1 4.90140−460SBH SOT23−3MAX809SN490T1G 4.90140−460SBH SOT23−3(Pb−Free)MAX809SN120T1G 1.20140−460SSO SOT23−3(Pb−Free)MAX809SN293D1T1G 2.931−3.3SSP SOT23−3(Pb−Free)MAX809SN293D2T1G 2.9320−66SSQ SOT23−3(Pb−Free)MAX809SN293D3T1G 2.93100−330SSR SOT23−3(Pb−Free)MAX809SQ120T1G 1.20140−460ZD SC70−3(Pb−Free)MAX809SQ232T1G 2.32140−460ZE SC70−3(Pb−Free)MAX809SQ263T1G 2.63140−460ZF SC70−3(Pb−Free)MAX809SQ293T1G 2.93140−460ZG SC70−3(Pb−Free)MAX809SQ308T1G 3.08140−460ZH SC70−3(Pb−Free)MAX809SQ400T1G 4.00140−460SZ SC70−3(Pb−Free)MAX809SQ438T1G 4.38140−460ZI SC70−3(Pb−Free)MAX809SQ463T1G 4.63140−460ZJ SC70−3(Pb−Free)MAX809SQ293D1T1G 2.931−3.3ZK SC70−3(Pb−Free)MAX809SQ293D2T1G 2.9320−66ZL SC70−3(Pb−Free)MAX809SQ293D3T1G 2.93100−330ZM SC70−3(Pb−Free)†For information on tape and reel specifications,including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.*Contact your ON Semiconductor sales representative for other threshold voltage options.ORDERING, MARKING AND THRESHOLD INFORMATIONPart Number V TH*(V)Timeout*(ms)Description Marking Package Shipping†MAX810RTR 2.63140−460Push−Pull RESET SPX SOT23−33000 / Tape & ReelMAX810RTRG 2.63140−460SPX SOT23−3(Pb−Free)MAX810STR 2.93140−460SPY SOT23−3MAX810STRG 2.93140−460SPY SOT23−3(Pb−Free)MAX810TTR 3.08140−460SPZ SOT23−3MAX810TTRG 3.08140−460SPZ SOT23−3(Pb−Free)MAX810MTR 4.38140−460SQA SOT23−3MAX810MTRG 4.38140−460SQA SOT23−3(Pb−Free)MAX810LTR 4.63140−460SQB SOT23−3MAX810LTRG 4.63140−460SQB SOT23−3(Pb−Free)MAX810SN120T1G 1.20140−460SSS SOT23−3(Pb−Free)MAX810SN293D1T1G 2.931−3.3SST SOT23−3(Pb−Free)MAX810SN293D2T1G 2.9320−66SSU SOT23−3(Pb−Free)MAX810SN293D3T1G 2.93100−330SSZ SOT23−3(Pb−Free)MAX810SQ120T1G 1.20140−460ZN SC70−3(Pb−Free)MAX810SQ263T1G 2.63140−460ZO SC70−3(Pb−Free)MAX810SQ293T1G 2.93140−460ZP SC70−3(Pb−Free)MAX810SQ438T1G 4.38140−460ZQ SC70−3(Pb−Free)MAX810SQ463T1G 4.63140−460ZR SC70−3(Pb−Free)MAX810SQ293D1T1G 2.931−3.3ZS SC70−3(Pb−Free)MAX810SQ293D2T1G 2.9320−66ZT SC70−3(Pb−Free)MAX810SQ293D3T1G 2.93100−330ZU SC70−3(Pb−Free)†For information on tape and reel specifications,including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.*Contact your ON Semiconductor sales representative for other threshold voltage options.PACKAGE DIMENSIONSSOT−23 (TO236)CASE 318−08ISSUE AN*For additional information on our Pb−Free strategy and solderingdetails, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.SOLDERING FOOTPRINT*ǒmm inchesǓSCALE 10:1NOTES:1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.2.CONTROLLING DIMENSION: INCH.3.MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEADTHICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL.4.318−01 THRU −07 AND −09 OBSOLETE, NEW STANDARD 318−08.VIEW CDIM A MIN NOM MAX MINMILLIMETERS0.89 1.00 1.110.035INCHES A10.010.060.100.001b 0.370.440.500.015c 0.090.130.180.003D 2.80 2.90 3.040.110E 1.20 1.30 1.400.047e 1.78 1.90 2.040.070L 0.100.200.300.0040.0400.0440.0020.0040.0180.0200.0050.0070.1140.1200.0510.0550.0750.0810.0080.012NOM MAX L1 2.102.40 2.640.0830.0940.104H E0.350.540.690.0140.0210.029MAX809 Series, MAX810 SeriesPACKAGE DIMENSIONSSC−70 (SOT−323)CASE 419−04ISSUE Mǒmm inchesǓSCALE 10:1*For additional information on our Pb−Free strategy and solderingdetails, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.PUBLICATION ORDERING INFORMATION元器件交易网。

Devices offered in this series are as follows:
PART
DESCRIPΒιβλιοθήκη IONMAX463 MAX464 MAX465 MAX466 MAX467 MAX468 MAX469 MAX470
Triple RGB Switch & Buffer Quad RGB Switch & Buffer Triple RGB Switch & Buffer Quad RGB Switch & Buffer Triple Video Buffer Quad Video Buffer Triple Video Buffer Quad Video Buffer
Continuous Power Dissipation (TA = +70°C) 16-Pin Plastic DIP (derate 22.22mW/°C above +70°C) ....1778mW 16-Pin Wide SO (derate 20.00mW/°C above +70°C) .......1600mW
The MAX463–MAX470 series of two-channel, triple/quad buffered video switches and video buffers combines high-accuracy, unity-gain-stable amplifiers with high-performance video switches. Fast switching time and low differential gain and phase error make this series of switches and buffers ideal for all video applications. The devices are all specified for ±5V supply operation with inputs and outputs as high as ±2.5V when driving 150Ω loads (75Ω back-terminated cable).