2 keyways,24 widex8 deep displaced 112° 2键槽 24阔x8深 错位112°3 hole φ10 eq （equally ）sp （space ）on 185pcd （pitch circle diameter ） 3—φ10均布（于φ185圆周上） 3-phase motor 三相交流电动机 3-roll-welding equipment 三辊矫直机机组 4-high-five-stand fully continuous tandem cold mill 4辊与机架全连（无头）冷轧机 5×45o chamfered on both front ends 两端面均倒5×45o 角 5-stand tandem mill 五机架连轧机 12 holes φ23 bored by assembly 12—φ23装配钻 (all) rights reserved 版权所有 about 大约 abrasion 磨蚀、磨损 abrasive 磨料 abt. all 6m of pipe one welding bushing 大约6米的管子都有一个焊接头 abt.（about ） 250 bar 约250巴 acceleration-time 加速时间 acceptance 验收 acceptance depute 验收负责人 acceptance schedule 验收内容（项目） acceptance test certificate 验收试验合格证 accessibility 可接近性，装拆性 accessories 配件，附件 accessory 附件 according to 按照 according to international practice 按照国际惯例 according to plan 按照计划 according to requirement 按照需要 account for 解释，说明 accumulator 蓄势器 accuracy 精度 accurate dimension determine by assembly 确尺寸安装时决定 accurate length decided by assembly 精确长度在安装时决定acetylene gas bottle 乙炔瓶 acoustic sensibility （起动）灵敏性 active outline 有效辊型长度 actual size 实际尺寸 addendum circle 齿顶园 additive （油中的）添加剂 adhesive material 粘合材料 adjust 矫直,弄直，修整 adjust roll axles parallel at workshop assembly tolerance ±0.03mm by 1m 车间装配时，轧辊轴线必需平行，其允差1m 为±0.03mm adjustability 可调节性 adjustable 可调的 adjustable starting position by displacement of the bolt guide 移动导向螺栓，调整起始位置 adjusted by erection 安装时调整 adjusting 装配，配合，调节adjusting device (轧辊）压下装置,调整设备 adjusting screw 调节螺丝 adjustment 调节，调整 adjustment mark 调整记号 adjustment screw 固定螺钉，调节螺钉 advanced training 进修，深造 after the alignment of the balustrade welded when erected 装配时调整栏杆后再焊接 after welding annealed for free of stress 焊后消除应力 against corrosion 防蚀 age 贮存，时效 align 矫直,弄直，修整 align 对准，校准，调准 alignment 矫直 alitizing (钢铁表面)渗铝法 all fillets r5 unless stated otherwise 其余园角r5 all in metric system 全为公制 all pipings have to be fitted at thebuilding site所有的管道必须在工地装配all radii r10 unless stated otherwise 其余半径r10all steel 全钢all steel construction 全钢结构all surfaces blacking 全部发黑allowable stress 许用应力allowance 余量alloy 合金alteration 修改alternating current-commutatormotor 交流整流器电机alternating load 交变负荷alternating stress 交变应力，动应力alternative 交变的aluminum 铝aluminize 渗铝analog-digital converter 模拟数字转换器anchor bolt 地脚螺钉anchor box (plate) 底板anchoring parts 地脚螺钉及配件angle 角，角度angle bar 角钢angle iron 角铁，角钢angle sander (直) 角 (形) 砂轮，圆盘砂轮angle valve 角焊angle with equal legs 角钢anneal 退火annealing 退火annex 附件，附录announcement 通告，宣告，通知annual output 年产量annular seal 园垫圈anticorrosive agent 防锈剂anti-corrosive paint coat 防锈涂层anti-crimping roll 抗弯卷辊（轧机后）antifriction bearing 滚动轴承apparatus 设备apparatus 仪器，设备applicability 应用可能性application 采用approximate formula 近似公式approximate value 近似值area 面积表面，平面area load 单位面积荷重argon arc welding 氩弧焊arrangement 排列asbestos 石棉asbestos cord 石棉绳aside platform 侧面平台assemble the pipelines according to the local 管道在安装时，按实际情况铺设assembling shop 装配车间assembly 安装，装配, 组件assembly drawing 装配图assembly production equipment 成套设备assembly supply 全套供应a term of contract 本合同的一条款项attachment 配件, 附件，装置attention 注意attention welding joint must be prepared for x-ray examination 焊缝必须用x光检验audlting 审计、审核autogenous welding 气体熔焊autogenous welding by pressure 热加压焊automatic 自动的automation 自动化auxiliary 辅助的，附属的auxiliary device 辅助设备average 平均的，普通的axial bearing 止推轴承axial force 轴向力axial or thrust load 轴向负荷axial pressure 轴向和axial stress 轴向压力axis of gravity 重心轴线axle 轴，车轴axle guard or support 轴端挡板back center （车床的）尾顶尖back coat 背面涂层back pressure 背压back roll 下辊back stroke 回程back up roll 支承辊backing roll 支承辊backing roller table 支承辊道balance automation 自动校平衡机balance weight 平衡块balancing 平衡balancing weight 平衡重量ball 球ball bearing 球轴承ball cup 锥面垫圈ball handle 球头手柄ball pin 球头杆（轴）band steel 带钢bandage 捆扎带bander 捆扎机banding machine 捆扎机bank 毛坯bar 棒，棒料bar steel 棒材bar stock 棒料bar stock feeder 坯（棒）料送料机barrel of a roll （轧）辊身长度base 基础，基地，基数base material 原料，坯料basic hole 基孔basic principle 基本原则，基本原理basic shaft 基轴batch stamp 批号、钢印，发货be the basis of 以......为基础be grouped as 分类为…be in alignment line up 在同一直线上beam 横梁becking 扩口，扩径，辗轧bed plate 底座belong to 属于belt 皮带belt conveyor 皮带输送机belt drive 皮带传动belt transmission 皮带传动belt wrapper 皮带助卷机bend 弯曲bend pipe 弯管bending cylinder set 弯辊缸bending machine 弯曲机bending moment 弯矩bending press 压弯机bending radius 弯曲半径bevel 斜块、斜坡bevel gear 园锥齿轮, 伞齿轮bevel gear roll table 伞齿轮辊道billet 初坯，坯料binary 二进制的binding device 连接设备black malleable iron 黑芯可锻铸铁blacking 发黑blank 来料，坯料blank flange 无孔法兰盘block 块block diagram 方块图block length 锭长blow out 吹净blueprint 兰图blueprint 蓝图,详细计划bold type indicates preferred sizes 黑体字尺寸推荐使用bolt 螺栓bonnet 闷盖booster 增压器bore φ5 for split pin drilled at assembly装配时，钻φ5开口销用孔bored by assembly 装配钻boring head （鏜床）刀排，鏜排，鏜头boss 轴套boss φ25 drill and tap m12×1.25 throughφ25搭子，攻穿m12×1.25bottom knife 下刀片bottom roll 下辊bottom view 仰视图bottom plate 底板bracket 支架bracketed sizes 括号内的尺寸bracketed sizes should be avoided wherever possible括号内的尺寸，尽可能不采用brake 制动器brake disc 圆盘闸，制动盘brake valve 制动阀branch 分部brass 黄铜breaker 安全臼,（轧机）安全臼break-through for filling pipe near the montage opening在装配孔旁穿孔充油管道brick-making press 压砖机bridle roll 张力辊bridle roll unit （活套）张紧辊装置bright drawn 光拔的Brinell hardness 布氏硬度Brinell test 布氏硬度试样brittleness 脆性bronze bearing 青铜轴承brushing device 清刷装置bubble pressing 气囊充压buckling roll 弯拆辊buffer spring 缓冲弹簧builder 制造者building performance 土建building-up welded 堆焊的built in 内装的built in motor 内装式电动机bumper 缓冲器，挡板bundle 包，捆burden plate 载重标牌burr 焊瘤burr machine 修边机burr masher 去毛刺机burring 去毛刺bush 衬套bushing 衬套, 套管,衬套by pass 旁通c bore 平底扩孔cable 钢索，电缆cage 隔圈calculated value 计算值calculating diagram 计算图表calculating machine 计算机calculation 计算calculation example 计算示例calculation rule 计算规程calibration 定径calipers 卡规cam 凸轮cam drive 凸轮传动camber 曲率cannon 旋转套筒cant （过渡处）斜度倒角cantilever beam 悬臂梁cap 帽，罩capacitance 承载能力capacity 容量capacity 压力下capacity of memory 存储量capital amount 投资额car 小车car body 车体，车箱carbide 碳化物carbon steel 碳钢carrying capacity 载重力carrying trough 承料槽carryover table 输送台cascade 串联cascade system 串联系统casehardened depth of hardeningzone≈0.5mm hv=800±40 kp/mm2表面淬火,渗碳深度0.5hv=800±40 kp/mm2 casehardened hv=780±40 kp/mm2 表面淬火hv=780±40 kp/mm2casehardening 表面硬化处理 (渗碳) cast 铸件cast iron with ball graphite 球状石墨铸铁cast piece 铸件cast steel 铸钢casting 铸件cast-iron with lamellar graphite 灰铸铁catalog 目录catalogue-small part 小件目录caustic 腐蚀的，灼烈的caution warning 注意cement 渗碳cemented-carbide 硬质合金center of lifting machine 升降装置中心centering car 对中小车centering ring 定心环central lubrication 集中润滑centrifuge 离心机ceramic 陶瓷的ch hd 圆柱头chain conveyors 链式输送机chain drive 链传动chain pull 链拉力chain sprocket 链轮CHAM 倒角（chamfer）chamfer 焊接坡口，棱角chamfer cutting 切倒角change gear 变速齿轮Channel 通道,信道Channel 槽钢Chapelet furnace 查佩利特（电极电弧）炉character 特征characterization 符号，标记charge （设备）利用率，装料charge and product classifying 定货和产品编排（分类）charger 装料机chart 表chd（checked by）审核check 轴承座check bolt 止动螺钉check nut 防松螺母check up 校对check valvechecked by 审核checker plate 纲纹钢板checking 核对chemical composition 化学成分chief designer 总设计师chill 淬火,激冷chilling 淬火,激冷chip 切屑chrome molybdenum 铬钼钢chrome nickel steel 铬镍钢chrome steel 铬钢chromium 铬chromium steel 铬钢circle 圆周circuit drawing 线路图circular cutting 园盘剪circular knife shears 园盘剪circular knife-trimming shears 园盘切边剪circular shears 园盘切边剪circulating oil 循环油circulating pump 循环泵circulating system 循环系统circulation 循环circulation line 循环管circumference 圆周circumferential force 切线力，圆周力cl or l,ξ中心线claim 要求,需要clamp 夹钳，夹持clamping bolt 压紧螺栓clamping nut 锁紧螺母clamping ring 夹紧环clamping roller 张紧辊，紧带轮classification 分类,级别，等级claw element 支撑块，支撑板clean neatly 清理干净cleaning （油）净化cleansing machine 净化机cleansing process 清洗（过程）clear off 吹净client 顾客，买主，用户clipper 弹簧夹clockwise 顺时针方向close or force fit 紧配合，压入close tolerance 较高的（精度）公差closed flange 封头法兰，端部法兰closed ring 加强环clutch 联结, 离合器coat and color 油漆和着色coated roller 涂层辊coating 涂层cockpit cover 防护罩code 代码,编码code number 订货单，代号coefficient of friction 摩擦系数cogging mill 初轧机coil 钢卷升降车coil buggy 带卷（运输）小车coil car 钢卷车coil guide 导向台coil opener 开卷装置，带卷直头机coil packing （钢）卷coil peeling knife 开卷刀coil pipe 蛇形管coil scales 称重车coil upender 翻卷机coil weighing machine 称卷机coiler 卷取机coiler rotor 卷筒coiler weight 卷重coiling 成卷卷取coiling position 卷取位置coiling device 卷取装置，卷绕装置coincidence 符合，一致，重合coining 墩粗，顶毂coining or embossing machine 打印机cold drawing 冷拔cold drawn 冷拔的cold rolling mill 冷轧机cold straining 冷态延伸cold strip thickness （冷轧后）成品厚度collar 轴套，隔环collector 换向器，收集器color coating line 涂层（机组）color stamper 着色打印机column 支架，立柱column of water水柱（高度）column row （厂房）立柱combine 联合企业combined unit 联合企业coming into force 生效，开始有效command 指令,命令,指挥compasses, 圆规，两脚规compatibility condition 相容性条件competent personnel 主管专业人员competent position 主管（执行）部门complicated 复杂的component 零件，单件，构件compression spring 压缩弹簧computer 计算机concentricity error 径向转动偏差condensate discharge 冷却水排放器conditions of delivery 交换条件conditions of visibility 直观性conical spring 园锥形弹簧connected load 传动（驱动）功率connecting housing 防护箱，连接箱connecting pipe 连接管connection 线，通路，接头，合闸，连接connection board 连接板connection diagram 接线图connection dimensions 连接尺寸connection for pressure gauge 力表用接口connection from valve and casing with waste screwings of flange阀和装箱的接口用法兰废螺钉封上conservation 封存（涂防锈油）constant 常数constant speed 恒速construction 结构construction 执行，开工，结构，设计construction 设计，结构，形状construction plan 施工布置（平面）construction unit 构件，元件contact angle 接触角contact length 接触长度contact reflection control 承载分布(图)检验contact surface 支承面container 容量，容器content 含量contents 内容，目录continued on page 2 下转第2页continuous 连续的continuous annealing line 连续退火机组continuous casting plant 连续浇铸设备continuous operation 连续运行continuous pickling 连续酸洗continuous production 连续生产continuous rolling mill 全连续轧机continuous twist 旋转架（记人数用）contour 外形,轮廓contract 合同contract 收缩contract item 合同对象（内容）contract text 合同本文contract no.（order no.）合同号（订货号）contractor 承包商，承包厂家control computer 调节计算机control desk 操纵台control element 操纵部件control lever 操纵杆control room 配电室conventional break line 波浪先(俗称断裂线)conventional operation 合作生产费conveyor beam 运输梁conveyor belt 输送带cool 冷却，凉的coolant 冷却剂cooler 冷却装置cooling coil 冷却蛇形管cooling section 冷却段，冷却装置cooling water 冷却水cooperation partner 合作伙伴coordinate 坐标copy 复制图，付本形式的corner 棱角corner joint weldings 角阀corner joint（weld）角焊corners to be removed, remove sharp edges 锐角倒钝，去毛刺corrective factor 修正系数corrective work 修改工作correlation 相互关系correspondence （联络）通讯corrosion 腐蚀corrosion 腐蚀corrosion-resisting 抗腐蚀性corrosive 腐蚀剂corrosive power 腐蚀能力corrugated sheet metal 瓦楞铁皮corrugating line 瓦楞机组counter 对接counter flange 对接法兰counter shaft 天轴counter weight 平衡块counterbalance 平衡块counterbore 平底扩孔counter-sink 平刮，钻埋头孔countersund head 沉头countersunk 锥口孔countersunk screw 埋头螺钉counterweight 平衡块coupling 联轴节cover 盖子covering letter 说明信，附信crane-travel gearing 吊车行走机构Crank 曲柄,手柄crank arm 曲柄臂crank axle 曲轴crank handle 手摇柄crank web 曲柄臂crankshaft 曲轴credit 贷款creep motion drive 蠕动，驱动crop 切头crop shear 切头剪cropping 切头cross beam 横梁cross section 截面，断面cross section dimension 断面尺寸cross sectional drawing 截面图cross shear cutting 切头剪(固定的)，分段剪cross-cut shear 横剪Crossed shaft 交叉轴cross-shears 横剪cross-staff head coupling 十字头连轴节crown （轧辊）凸度crown nut 槽形螺母crowned 中凸的，球状的core 中心crush 压碎cone hole 锥口孔sink hole 沉头c-type hood c型钩curling 卷边curved teeth 弧型齿轮customer 订户，买方customer 用户cut out by assembly 装配时割cut to length 定尺剪机cutlet leveler 出口矫直机cut-of production 生产中断cutter 切削刀具，刀具cutting 切割，剪切cutting-holder 刀架cylinder 圆柱体或圆柱形的cylinder 气缸cylinder 圆筒,气缸daily output 日产量dampen 挡料板damping 支持器，夹紧装置danger of breaking 断裂危险date 日期date of delivery 交货期限（日期）day（or date）日期daylight 封闭高度，安装高度deacaling 环氧树脂粉decimal system 十进制declutch 断开decoiler 开卷机decremental hardening 局部淬火dedendum circle 齿根圆defect 缺陷处deficient part inspection 废品件检验deflecting roll set 导向辊组deflection 挠度deflector roll 转向辊deforming procedure 轧制过程degreasing 去油，脱脂degree of shrinkage 收缩率delivering live-roller table 输出辊道delivery 出口delivery 流量delivery device 补偿装置delivery flow 流量（升/分）delivery part 外构件delivery section 出口端delivery volume 排量（升）delivery-feed side looping tower 出口－进口活套塔demand 要求、需要denomination 名称，符号，命名denomination or designation 名称deposit 贮存，时效dept（department）科、部门depth 深度depth of tooth 齿高desealing 除鳞，消除氧化皮deseaming machine 焊缝清铲器dashed line （curve）虚线designation 名称design 执行，开工，结构，设计design 设计，结构，形状designation 名称，符号，命名designer 制图员designer 设计者desuperheater 蒸汽冷却器detail 局部放大detail drawing 零件图detector searcher 探测器detuning 失调，不平衡developed length 63 展开长度63 diameter 直径diametral pitch （齿轮）径节Die 冲模,硬模die cast metal 压铸金属die forging press 模锻压机differential character 误差特征differential gear 差动齿轮differential pulley 差动滑轮digitizing method 数字法dimension 公差，尺寸dimension fitted by assembly 此尺寸装配时调整dimension in bracket shouldn't be machined括号内尺寸无需加工dimension in mm 尺寸（mm）dimensions printed in bold are preferential黑体字尺寸推荐使用dip roll 浸没辊direction 说明，指示（节），方向，指导direction for use 使用说明（规范）directions for use 使用说明directive 有指向的director 指导者,厂长,经理,控制器director of arrow 箭示方向discharge 流量description of functions 性能（动作）说明dismounting 拆卸dismounting sleeve 换辊车disparity 偏差，不一致displacement 排量disposition 布置，安排dispositions plan 平面布置图distance between 轴距distance ring 定距环distribution of stress 应力分布distributor 分配器distributor gear 分配减速机divided circle scale 周节dividers 圆规，两脚规domestic price 国内价格dosing pump 计量泵，取料泵dotted line （curve）点划线doublet iron 工字钢dowel pin 园柱销downtime 停车时间，辅助时间downward movement 向下运动downward velocity 下降速度drain 排泄draw in bolt 拉紧螺栓drawing 图drawing board 绘图板drawing board 画图板drawing compasses 绘图用两脚规drawing no. 图号drawing number 图号drawing pen 鸭嘴笔drawing supply 图纸提供drawn by 制图drawn without roller table 滚道未画出draw-off nut 压紧螺母dreftsman 制图员drier 干燥机drill 钻孔drill and ream φ10×20 deep 钻及铰φ10×20深drilled φ5 as vent by assembly 装配时，钻φ5排气孔drilling 钻孔drinking water 饮（用）水drip method 满浸法drip oiler 滴油器drive 开动，传动drive according to drawing no.--- 传动按图号drive housing 传动装置箱，齿轮箱drive off 输出drive out 输出drive shaft 传动轴drive side 传动侧driving axle 传动轴driving element 操纵件driving roll 工作辊，传动辊driving shift 传动轴drop forging 模锻drum switch 鼓形开关drwg. no.（drawing no.）图号drwg.-no. of counter wheel 配偶齿轮图号dryer 干燥机drying 干燥ductile 延性的，可锻的dull 钝的duplicator 复制机,靠模装置earth roll 托辊easy maintenance 便于管理eccentric 不对中心的eccentricity 径向摆动economically 经济的，节省的edging stand 立轧机座effective coils 16 （working coils 16）有效圈数16effective height 有效高度effective or root mean 有效高度CGS-system 厘米-克-秒制eigen temperature 室内温度ejector 顶杆ejector pin 顶杆elastic coupling 弹性联轴器elastic force 弹力，弹性elasticity 弹力，弹性elasticity 弹性elbow 弯头electric connected load 650w 电气设备容量650kwelectric hoist 电动葫芦electric housing screw 电动螺丝压下装置electric oiler 静电涂油机electric power 电动驱动装置electrical control equipment 电控设备Electrolytic 电解的electrolytic galvanizing line 电镀锌机组electrolytic pickling 电介酸洗electrolytic tinning 电镀锡Electroplate 电镀electroplating shop 电镀车间elevator 升降机elimination 脱掉，除去，停止elongation 延伸率embossing 墩粗，顶毂empirical formula 经验公式end effect 末端效应，最终效果end of spring 弹簧端面end piece 端梁end plate 挡圈end step 挡板endless milling 全连续轧制，无头轧制endurance strength 有限持久强度energy converter 能量转换器engagement 啮合engineering project 工程设计entry 入口entry-section 进口部分，（端）进口段environs temperature 外界温度epoxy resin paint 环氧树脂漆equation 方程式，等式equipment 设备equipment which is ready for production "交鈅匙”设备equivalent 等效的erosion 腐蚀,侵蚀european projection 欧式投影（第一角画法）europe-type beam 欧洲型工字梁（ipe300）evaporator 汽化器exact 精确的，精密的example of application 应用举例exfloiate 片裂exhaust pipe 排气管exhaust pipe 排出exit accumulator （带钢）出口储存轮expand 扩张，膨胀expanding drum （卷取机）胀缩筒expert 专家(external) edges broken 倒角external form 外形extra weight 过重，超重extractor 推料机，顶出extrusion 挤压extrusion press 挤压设备eye bolt 环首螺栓gag adjustment cylinder 压下缸gage 量规，测量galvanization 电镀galvanizing 电镀锌, 镀锌gap 间隙，辊隙gas 煤气gasket 密封垫, 密封片, 垫圈, 衬垫gas nitrided 气体氮化gas piping 煤气管道gas pressure 气体压力gas proof 防煤气的，不透气的gas valve 煤气阀gas welding 气焊，氧乙炔焊gas welding apparatus 气焊设备gauge block 块规gear 齿轮箱，机构，齿轮gear box 齿轮箱gear hub 轮毂gear inching speed motor 齿轮精密马达gear motor 齿轮马达gear pump 齿轮泵gear rack 齿条gear ratio 齿轮速比gear ratio 速比，传动比gear train 齿轮系,齿轮传动装置gearing faulty pitch 基节偏差gearing flank clearance 齿面啮合间隙general 一般性，通用性general description 综述，说明general plan 总布置图general view 总图generality 一般性，通用性generator 发生器German industrial standards 德国工业标准gestretch 拉伸的，伸长的gib head taper key 钩头楔键girder 梁give 给出的，列出的globule 焊瘤glow lamp 白炽灯glycerine manometer 甘油压力表grade 质量等级, 类别，等级gradually 同步地，断续地grain 晶粒，颗粒grain（hair） side 毛面graphically 用图示,用图解graphite wire 石墨线gravity roller conveyer 辊式运输机gray cast iron 灰铸铁grease 油脂grease gun 油脂枪，牛油枪grease pump 润滑油泵grease proof paper 防油纸grease-filled by assembly 装配时注满油脂greatest possible rolling speed 最大可能的轧制速度greatest size 最大尺寸grind 磨，磨削grinding machine 磨床grinding wheel 砂轮grooved rolled gear 人字齿轮减速机groover close automation 自动封槽机gross （量、数的）总共的gross formula 经验公式gross weight 总重量，毛重ground painting 涂底漆ground plan see drawing no---- 平面布置图参阅图号----ground roll 底部辊ground roll station 地辊站grounding roll 托辊guard 防护罩guard rail mounted by customer ！安全栏杆由用户安装！guard ring 安全坏，保护环guide 指南guide block 导向滑块guide bushing 导套guide frame 导向架guide piece 导向块guide pipe 导管guide plat 导向板, 夹板guide rod 导向杆guide roll set 导向辊组guide slide 导轨，滑轨half round steel 半园钢half section 半剖视hand book 手册hand drive 手动hand wheel 手轮hand-key 按钮handle 手柄（旋转器）hand-point of lubrication 手加油点handrail 栏杆hand-tool motor 手动工具电机hard material 硬质材料hard paper 纸胶板hard wood 硬木harden 硬化，淬火hardened throughout 全淬hardness 硬度hardness depth 渗碳深度heat falling in 热渗透heat shrinking 热压配合heat treatment certificate 热处理合格证heat-treat 热处理heat-treated to 6s>60 kp/mm2 热处理6s>60 kp/mm2heavy gauge sheer 横切机组height from bottom 离地高度Helical gear 斜齿轮helical gearing 斜齿啮合helical gear 斜齿圆柱齿轮helix angle 螺旋角here no welding seam 此处无焊缝herringbone gear 人字齿轮herring bone gearing or teath 人字齿轮hetero-polar machine 异极电机hexagon bar 六角钢hexagon head 六角头high cost 费用大的high grade steel 高级钢high pressure hose 高压软管high pressure side 高压侧high quality cast 优质铸块high speed 高速high speed steel 高速钢high quality steel 优质钢，高级合金钢hinge coupling 万向联轴节hoist 起重机，升降机hoist table 升降台hold down roll 接受高度（以锥开卷机轴线高度）holding down attachment 压下装置hole φ 10h' reamed together with reing no.665870/1φ10h'孔与图号665870/1同铰hood 罩hook 钩子，吊钩horse power 马力hose 软管hose joint 软管接头hot galvanizing 热镀锌hot galvanizing line 热镀锌机组hot-dip tinning 热镀锡housing 外壳，吊钩，吊架，住宿，轧机机座hrc55-60 depth of he dining zone 0.3mm.渗碳深度0.3mm，hrc55-60HSTP=high strength 高强度hub 轮毂humidity 湿度hydraulic cylinder 液压缸hydraulic equipment 液压设备hydraulic motor 液压马达hydraulic oil 工作介质（油）hydraulic pipeline 液压管路hydraulic screwdown 液压压下装置hydraulic tongs tilters 液压夹式翻钢机hydraulically actuated wedge adjustment system液压楔形调节系统hydraulic-and pneumatic-equipment 液压气动设备hydraulic-caller 油库hyphen 连字符，短划hysteresis 滞后I-beam 工字钢I-beam section 工字形断面，工字钢identification code printer 标号打印器idle roll 从动轧辊，空转辊Illustrate 图解,说明inclined plane 斜面impact resistance 抗冲击强度impact test 冲击（碰撞）试验impregnating method 沉浸法impregnation 浸渍imprint 印记,记录impulse sender 脉冲发生器in duplicate 一式两份in order that 为的是，以便in order to 为了in sections 组合in squads 组合的in the form of 以…的形式in triplicate 一式三份inch 英寸increased height 超高index 索引，目录indication 记号，标注induction motor 感应电机industrial waster water 工业废水internal crack 内裂纹inert gas 惰性气体inertia 惯性in-feed 分交，配套informations to the unit 机组说明initial dimension 原始尺寸initial temperature 原始温度，标准温度initial thickness 轧前厚度inland customer 国内用户inlet 入口input 输入量, 输入inquiry 询价insert 插入inside caliper 内径卡inside diameter 内径inspect 检验，检查inspection 校对，审核inspection glass 窥视孔玻璃inspection hole 窥视孔inspection station 检验台install lament 分期付款installation 安装，定位，调整installation an operation 安装及调试installation dissension 安装尺寸installation drawing 安装图instruction 说明书,说明,指示(节),指令insulating 绝缘insulating roll 绝缘辊integral integrant 组合的internal grinding machine 内园磨床interchangeable 可互换的intermediate 中间的intermediate basering 中间支座intermediate layer 垫片intermediate position 中间位置intermediate shaft 中间轴intermitted fillet welding 断续角焊internal friction 内摩擦internal gear 内齿轮internal micrometer 内径分厘卡internal stress 内应力internal thread 内螺纹interrupt 中断，移出into atmosphere 排入大气（背压）introduction 序言iron mold 金属模，钢锭模iron waste 铁鳞iron wood 硬木isolation-type gas accumulator隔离式气体蓄势器italics（print）斜体字item 项，章，节，情况jacks 支持器，夹紧装置jet-knife 气刀jig 夹具,钻模joiner's shop joinery 木工joint 接头,接线，通路，接头，合闸，连接joint face 接合面，分型面journal box 滚柱轴承，轧辊轴承key seat 键槽kind of stressing 应力know-how supplier 技术诀窍提供者knurl 滚花keeper plate 挡板ladle 铁水包laminated fabric plate 胶布板lamination 分层（缺陷），折叠（板材）lap 搭接lap joint 搭接lap welding 搭接焊lathe 车床lay out 划线layout 设计布置（图）loop-storage pit 活套坑leaf spring 板弹簧leakage 泄漏leakage protection 防漏leakage test 泄漏试验leakiness 泄漏left side view 左视图length of engagement≈1.25d 旋入机体一端≈1.25dlength of fit 配合长度level 平整，修整，杠杆leveler 矫直机leveling machine 矫直机leveling unit 辊式矫直机lid 帽，罩lift drive 提升传动装置lift part 升降（提升）部分lifting 提升（起重）lifting cylinder 提升缸lifting device 提升装置lifting eyebolt 吊环螺钉lifting means 提升装置，提升机构lifting portion 提升部份limit of stress 应力极限limit switch 限制开关，终端开关line of self-inter-section 过渡线(俗称相关线)line-drawing of a link-line 流水作业线草图liner 衬垫，滑板lining 炉衬，衬套link 连杆,构件linkage 连杆机构,联动装置liquid 液体，流体liquid column 液柱liquid decontamination 液体净化liquid level indication 液位指示list 表，目录list of catalogue parts 产品目录list of hammer screws according to drwg.-no. 1006628t形头螺钉表按图号1006628list of spare parts 各件清单list of the stone bolts accord. to drwg.-no. 1007147地脚螺栓表按图号1007147list of the threaded bolts accord. to drwg.-no. 1007148螺栓表按图号1007148literature 专业报刊load 负载，载荷，负荷, 加载,装载load bar direction 支架方向load capacity 载重能力load diagram 负载图load plan 负荷图load plan see drwg.-no.1006170负荷图参阅图号1006170load relief 卸荷loading capacity 承载能力locate 定位，判定locating bearing 固定轴承lock nut 防松螺母lock washer 止动垫片locking device 止动器locking key 防松键locking pin 定位销，固定销locking plate 止动垫片looking device at both ends 两端部的锁紧装置loop 活套装置loop car 活套车loop pit 活套坑loop tower 活套塔loosed circulation 闭环lot 地皮，地面积low pressure 低压low pressure cylinder 低压缸low pressure side 低压侧low pressure test 低压试验lower 下面的，较底的 lower portion 下面部分 lower set of rolls 下轧辊组 lowering 沉刮 lubricant 润滑剂，润滑的 lubricant pipeline 润滑油脂管道 lubricate daily 每天润滑一次 lubricate every 1/2 year 每半年润滑一次 lubricate weekly 每星期加油一次 lubricating hole 润滑孔 lubricating nipple 注油咀 lubricating oil 润滑油 lubricating place 润滑部位 lubrication point 润滑点 lubrication ring 润滑油环 lubrication system 润滑系统 lubrications chart 润滑表 lubricator 注油器 lubricant 润滑油 lubricating device 润滑设备 lubricating oil pump 润滑轴泵 lubrication instruction 润滑规程（导则） m10 left m10(左旋) m10×1.5 drilled durin g shop assembly 车间装配时，攻m10×1.5 m6 depth of bore 12 depth of thread 8 m6深8，孔深12 m8 right m8(右旋) machining 切削 machining allowance 加工余量 machining datum surface 基准面 made in china 中国制造 magnesium 镁 magnet 磁石，磁铁，磁体 magnetic 磁性的 main girder 下支架 main bottleneck 主要薄弱环节 main control desk 主操纵台 main dimension 主要尺寸 main slide 主滑道 main switch 总开关 maintenance 维护，保养, 维修 maintenance costs 维护费用 maintenance instruction 保养（维修）规程（范） maintenance platform 维修平台 maintenance stand 维修台 major 主要的 male thread 外螺纹 malleability 可锻性 man hole 人孔 manganese 锰 manipulator 操作机 manufacture 生产，制造 manufactured in china 中国制造 manufacturer 制造厂代号 manufacturing in series 批量生产 mark 符号，标记 mash 捣碎 mass production 大量生产 mass-and small production 大批量和小批量 matching 装配，配合，调节 mate 配合 material 材料 material mark 材料标记（符号） mating gear 配偶齿轮 matl （material ） 材料 maximum 最大的，最大值 mean speed 平均速度 measuring and control equipment 测量和控制设备 medium 中型的，中等的；手段，媒介 medium 媒介,介质,手段 melt 熔化 member 构件，元件 men hole 入孔 mesh 啮合 metal net 金属网 method of application 使用方法 method of approximation 近似法 method of calculation 计算方法 method of welding 焊接法 micrometer 千分尺，测微计 mierograph 切片图（内部组织结构图） mild steel 软钢 mill 铣；铣刀milling 铣床milling cutter 铣刀minimum 最小的minimum value 最低值minimum size 最小尺寸miscalculation 计算误差mistuning 失调，不平衡mixer 搅拌机mobility 灵活性model 执行，开工，结构，设计modification 修改module 模数modulus of elasticity 弹性模数mold 模型,铸模monitoring, control 控制器monorail motor hoist 单轨电葫芦monthly output 月产量morgoil bearing 油膜轴承motionless 不动的，静止的motor control 电动机控制motor for fast speed 快速马达motor rate 电机功率motor speed 电机转数mount base 机座mounting 安装，装配mounting finished 安装好的moving change point 运动转换点moving seal point 运行密封点multiplayer drilling hole 多层钻孔multiple 多重的，复合的nailing machine 制钉机，打钉机name 姓名natural cooling 自然冷却natural leak 自然泄露needed operator 所需的操作者needle roller bearing 滚针轴承needle valve 针阀net weight 净重，自重nibbling 切割，剪切nickel 镍nickel content 含镍量nitrate 渗氮no power 无功率no. 10-60 are designations of the subassemblies序号10-60 为部件图的名称no. of modification information 修改通知单号码noble or precious metal 贵重金属nominal diameter 公称直径nominal pressure 公称压力nominal size 公称尺寸nominal width 通径nonferrous metal 有色金属nonferrous metal 有色金属non-ferrous metal 非铁金属non-return valve 单向阀normal module 法向模数normal plane pitch 法向模数normal pressure angle 法向压力角normal temperature 原始温度，标准温度normal temperature 标准温度not including packing 不包括包装not true to scale described 非比例表示notch 槽口，凹槽notice 记号，标注nozzle holder 喷咀架nozzle pipe 喷管nozzle tube 喷管number 数，数目number of blows permin 冲程数number of piece 件数number of revolutions 转数number of teeth 齿数number of threads per inch 每英寸牙数nut 螺母octagonal steel 八角钢odd number 奇数odd numbered 奇数的off-center 不对中心的oil application system 使用液压油的机组oil bath 油池oil change every year 每年换油一次oil charge 加油量。
