Autodesk®Fabrication CAMduct™ 2014Service Pack 3 Enhancement ListImprovements made in Service Pack 3 build 3.02.706:Pattern Improvements∙CID 324 - Improved Initial Makepat units for Imperial configuration where they were previously showing as metric.∙CID 535 - Improved Draw Type Options.∙CID 64 - Improved Development.∙CID 1127 - Improved Collar Developments.∙CID 1142 - Improved Development.∙CID 1148 - Improved holes on Development.∙CID 854 - Improved faces visibility when Bottom Radius set to 0.∙Improved Fabrication items by allowing functions to be used in calculated dims.∙Improvement made to straight duct patterns as seams were not being removed with the holes.∙Improvements to Bend insulation faces.∙Stability improvement when loading jobs with dampers.Productivity Improvements∙Improved cloud nesting to restrict processing items from being nested on the context menu.∙Improved cloud nesting to set item statuses to prevent processed items from being selected for nesting.∙Improved Linear Nest part lengths to report the correct imperial units.General Usability Improvements∙Improvement to nesting to include slits on all duplicate parts when slits are required.∙Stability improvement when using delete NC.∙Improvements made to nesting so that v-notches are cut true to the development profile.∙Improvement made to installed machines, when no machines are listed to remember newly created entries.∙Improved selection drop down lists to stop scrolling when selections are made.∙Enhancements to data views to allow Window Selections.∙Improvement to nesting to include slits on all duplicate parts when slits are required.∙Improved Dynamic Holes Developments.∙Improvements made to Dynamic Holes when branches are mirrored.∙Improved Job Info to increment the number when creating a new job after Batch Process.∙Stability improvements made to Sheet Sectional Processing when used for moving bed machines.∙Stability improvement made to Strip Nesting.∙Improvement made to migration of legacy install where all folders were not being copied over.∙Stability improvement made to Path Repair Tool.∙Stability improvement made when merging using Cloud Nesting.General Database Improvements∙Improved Material Database columns to be consistent.∙CID 60 - Improved Item Data Export output fields.∙Improved stability on 1D Barcode when data is more than 10 characters.∙Improvement made to Export Items Data when reporting out Square to Round Offset Depth.∙Improved scripting for owned content.∙Improved stability to Product Information Viewer.∙Improvement made to Edit Configuration when a link is added.Print Objects Enhancements∙Improvement to item gauge print object to always display index number or thickness.∙Improved stability when adding reports that have pressure drop & velocity fields for calculations.Post Processor Improvements∙New post processor added to support a new controller by Sente Makina.∙Added decoiler post that outputs a decoiler file in the format required by the TS20100 controller.∙Added MACH 3 support for Tangential/Router tools with feet.∙Improvement made to Sente Makina Post Processor.∙Improvement made to Amada Post Processor for stitched holes.∙Improved TURBODBGEN Post Processor to support updated controller.∙Improvements made to Salvagnini Post Processor.∙Improved Dyna Torch Post Processor to optionally include Block Numbers.∙Improvement made to MachMotion Post Processor.∙Added Mazak L32 Post Processor.∙Added Schneider Post Processor.∙Added SENTEDB1GEN Post processor for Sente Makina Duct board machine.Service Pack 2 Enhancement ListImprovements made in Service Pack 2 build 3.02.600:Pattern Improvements∙CID 1113 - Marker notch option added.∙CID 148, 2148 & 2149 - improved annotations in viewer.∙CID 17 - Enhanced insulation development to support mitered inner throat settings.∙CID 2149 - Inlet and Outlet options made visible.∙CID 2160 - Removed dimension error warning when branch values are set to zero but still expecting a valid angle.∙CID 24 - Dynamic hole changed to match the hole, not the plate size.∙CID 2523 - Insulation trimming improvement.∙CID 2882 - Improved to maintain a sensible scale view when setting dim F (Left Collar) to auto.∙CID 4 - Improved insulation to be positioned correctly when inner radius is set to zero.∙CID 40, 2040 & 2041 - Option "Duct Length" renamed to "Pipe Length"∙CID 839 - Development change to correctly match parts where the branch offsets no tangentially to outside of the pipe diameter.∙CID 868 - Centreline and pattern length will now report the C1 to C2 distance.∙Improved collars to no longer require redraw before take-off.∙Improvement made to pipe patterns to always allow you to change the connectors.∙Improvement made to pipe patterns to always allow you to specify pipe length.∙Improvements made to various patterns to cut insulations where holes have been added.General Usability Improvements∙Improved dynamic holes so that existing holes will be preserved∙Improved sub-assemblies to report the correct price for each component in the assembly.∙Improved the watermark printing feature so now the watermark can print on every page.∙Stability improvements in manual nesting when using combinations of chain cut and undo.∙Stability improvements made to the layer dialog to allow multiple clicking on the background.General Database Improvements∙Annotation multiplier now calculates as expected.∙Improved .dxf export to allow you to select how much detail to include. See /Pattern Switches/Developments∙Improved database component matching so that each component group will be taking into consideration when matching by name.∙Improved export data wizard by supporting different font sizes, data will no longer disappear from the dialog.Configuration Enhancements∙Improved "Remember this next time" when selecting a configuration from the start up screen.∙Improvements made when copying configurations so that the correct paths will be displayed, also projects will not be copied.Post Processor Improvements∙Added a new Swift Cut post processor.∙Improved Mach3 post processor to allow duct board to be cut.∙Improvement made to Mach3gen post processor to include a "Go Home On Tool Change" feature.∙Improvements made to the Forstner post processor to allow overrides on length and connector allowances.Service Pack 1 Enhancement ListImprovements made in Service Pack 1 build 3.02.502:Pattern Improvements∙CID 10, 18 - Right Height value functions correctly.∙CID 1170 - Connector node positions corrected.∙CID 1177 - Developments corrected.∙CID 1177 - Double Wall option enabled.∙CID 29 - Collars now reporting diameter or length in item reports.∙CID 3 - Multiple connector adjusts now supported.∙CID 385 - Branch node position corrected when No Pipe option is used.∙CID 4 - Leg length option is always shown.∙CID 4 –Improvement made to pattern to remember the option Throat Type, previously when using “Mitered” and an extension was input, the throat would reset to “Radius” when redrawn.∙CID 4522 - Coupling inverted so now when inserted as open top this displays correctly.∙CID 502 - Stability improvement when opened in previous versions of Autodesk Fabrication products.∙CID 526 - Angle dim is now remembered when part is edited.∙CID 58 - Branch snap node is positioned correctly when branch only option is used.∙CID 7 - Improved accuracy of 3D model overall height if used with a connector with a straight allowance at the OM end.∙CID 8 - Bending information corrected.∙CID 850 - Improved stability when adding straight branch in imperial configurations.∙CID 866 - Corrected hole position when a connector with a straight adjust is used.∙CID 879 - Coupling Plate connector face orientations corrected.∙CID 880 - Faces orientation corrected.∙CID 891 - Branch orientation corrected.∙CID 900 - Improved stability when type set to Vertical Elbow and Redrawn multiple times.∙CID 95 - Resolved overlapping developments when nested.∙CID 966 - Annotations now show in 3D viewer.∙CID 970 - Branch connector location corrected.General Usability Improvements∙Display Real Values for Auto Data Oval bend CID 106,107,108,109 on reports∙Enhanced Import Export dialog will not display incompatible file types.∙Enhancement PMCut to resolve errors received while loading.∙Improved development of collars to always redevelop when changes are made.∙Improved interoperability on subassemblies between Fabrication Products, 2013 & 2014 versions.∙Improved login/logout functionality to now always present the user with a login window following a successful logout.∙Improved ReCut form so when selecting Request By Type as columns now update correctly.∙Improved ReCut form when cancelled to return to the welcome screen.∙Improved save/export .dxf feature to now use the specified file location.∙Improved stability in job browser when clicking to find next.∙Improved stability in manual nesting after using Simple Cut Order.∙Improved stability where parts lead-ins were undetermined as a machine was not correctly assigned.∙Improved stability with loading IFC files which was causing memory corruption issues.∙Improved various areas of the program to handle file names containing % characters.∙Improved workflow of nesting process when using sheet nesting.∙Improved stability when importing underlays of large file size.∙Improvement made to welcome screen to allow user to edit configuration's databases.∙Supressed multiple confirmation delete warnings when deleting NC data.Print Objects Enhancements∙Improved connector location print object as occasionally wrong connectors were displayed, usually when the cad end was not the same order as connectors.∙Improved stability when accessing print objects that were referencing invalid database components.∙Improvements made to database to include gasket Print Objects.General Database Improvements∙Improved oversize seams to allow unique setting to be entered into Square to Oval & Round to Oval.∙Improvements to tables to allow easier deselection when a select all is active.Configuration Enhancements∙Improved copy configuration feature so that only the local folders.ini is loaded.∙Optimised ITM file and bitmap loading across networksMapprod Improvements∙Improvements made to prevent filter buttons from vanishing when the columns were resized.∙Product Information Editor/Viewer now reads from common file locations.Post Processor Improvements∙Added the following new post processors:o Salvagninigen(64).vplo Sinumericgen(64).vplo Machmotiongen(64).vplo Wammes PA(64).vplo Alarsis(64).vplo Gomech4(64).vplo KEGKatana(64).vpl∙Improved Prima post processor to now load values from condition tables in machine set-up.∙Improved support for diamond stiffening.∙Revised the following post processors:o Lockformer 1000Do VICON"Opus Enhancements∙Enhanced to enable leads to be moved.∙Improved stability in Opus element offset if the arc is shrunk to zero.∙Improved stability in when importing a DXF with no developments.Improved stability when importing parts with marking text.Autodesk, the Autodesk logo and CAMduct are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the right to alter product and services offerings, and specifications and pricing at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document. © 2013 Autodesk, Inc. All rights reserved.。
目录写在前面 (3)一介绍 (4)二工具 (4)Java (4)Maven (4)Subversion (4)三源代码 (4)源代码 (5)提交 (5)库结构 (5)分支结构 (6)快速入门 (6)取出源代码 (6)由Maven构建 (7)由Maven生成Eclipse工程文件 (9)导入模块进Eclipse (9)在Eclipse中运行GeoServer (12)访问GeoServer首页 (13)Maven指南 (13)安装Maven (13)运行Maven (13)构建 (13)跳过测试 (14)离线构建 (14)构建扩展 (14)Profiles (15)Eclipse (15)构建Web模块 (15)使用Jetty运行web模块 (16)Eclipse指南 (16)导入模块 (17)运行和调试 (17)设置数据目录 (17)更改Jetty默认端口 (18)配置Jetty的JNDI资源 (19)Eclipse首选项 (20)代码格式化 (21)代码模板 (22)文本编辑器 (22)编译器 (23)OWS服务 (24)OWS服务概览 (24)实现一个简单的OWS服务 (24)建立 (25)创建插件 (27)试一试 (30)REST服务 (34)简介 (34)RESTful服务实现 (35)基于Maps的Restful服务实现 (42)基于反射的Restful服务实现 (47)GeoServer中的Wicket开发 (53)Web用户接口 (60)简介 (60)实现一个Wicket UI扩展 (61)写在前面一介绍二工具JavaMavenSubversion三源代码源代码提交库结构分支结构四快速入门取出源代码由Maven构建由Maven生成Eclipse工程文件导入模块进Eclipse在Eclipse中运行GeoServer访问GeoServer首页五Maven指南六Eclipse指南七编程指南八释放指南九释放测试检查列表十CITE测试指南十一政策与步骤写在前面我一直对OSGeo的软件和应用很感兴趣，希望致力于这些软件在中国的普及与应用，《GeoServer开发手册》是这些工作的一部分。
