英泰使用说明书 OLG-8100C2

UC-8100 Series Hardware User’s ManualEdition 3.1, September 2018/product© 2018 Moxa Inc. All rights reserved.UC-8100 Series Hardware User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance withthe terms of that agreement.Copyright Notice© 2018 Moxa Inc. All rights reserved.TrademarksThe MOXA logo is a registered trademark of Moxa Inc.All other trademarks or registered marks in this manual belong to their respective manufacturers.DisclaimerInformation in this document is subject to change without notice and does not represent a commitment on the part of Moxa.Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time.Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use.This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication.Technical Support Contact Information/supportMoxa AmericasToll-free: 1-888-669-2872 Tel: +1-714-528-6777 Fax: +1-714-528-6778Moxa China (Shanghai office) Toll-free: 800-820-5036Tel: +86-21-5258-9955 Fax: +86-21-5258-5505Moxa EuropeTel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99Moxa Asia-PacificTel: +886-2-8919-1230 Fax: +886-2-8919-1231Moxa IndiaTel: +91-80-4172-9088 Fax: +91-80-4132-1045Table of Contents1.Introduction ...................................................................................................................................... 1-1Overview ........................................................................................................................................... 1-2 Model Descriptions .............................................................................................................................. 1-2 Package Checklist ............................................................................................................................... 1-2 Hardware Specifications ...................................................................................................................... 1-2 Hardware Block Diagram ..................................................................................................................... 1-3 2.Hardware Introduction...................................................................................................................... 2-1Appearance ........................................................................................................................................ 2-2 LED Indicators .................................................................................................................................... 2-3 Default Programmable Button Operations .............................................................................................. 2-4 Diagnosing Device and Subsystem Failures ..................................................................................... 2-4 Reset to Default Button ....................................................................................................................... 2-5 Real Time Clock .................................................................................................................................. 2-5 Placement Options .............................................................................................................................. 2-5 DIN Rail Mounting ....................................................................................................................... 2-5Wall or Cabinet Mounting ............................................................................................................. 2-6 3.Hardware Connection Description ..................................................................................................... 3-1Wiring Requirements ........................................................................................................................... 3-2 Connecting the Power .................................................................................................................. 3-2Grounding the Unit ...................................................................................................................... 3-2 Connecting to the Console Port ............................................................................................................. 3-3 Connecting to the Network ................................................................................................................... 3-3 Connecting to a Serial Device ............................................................................................................... 3-4 Inserting the SD and SIM Card ............................................................................................................. 3-4 USB Port ............................................................................................................................................ 3-4 Installing the Cellular/Wi-Fi Module ....................................................................................................... 3-5 A.Regulatory Approval Statements ....................................................................................................... A-11Introduction The UC-8100 series computing platform is designed for embedded data acquisition applications. The computer comes with one or two RS- 232/422/485 serial ports and dual 10/100 Mbps Ethernet LAN ports, as well as a Mini PCIe socket to support cellular modules. These versatile communication capabilities let users efficiently adapt the UC-8100 computers to a variety of complex communications solutions.The following topics are covered in this chapter:❒Overview❒Model Descriptions❒Package Checklist❒Hardware Specifications❒Hardware Block DiagramOverviewThe UC-8100 Series is built around an ARMv7 Cortex-A8 RISC processor that has been optimized for use inenergy monitoring systems, but is widely applicable to a variety of industrial solutions. With flexible interfacing options, this tiny embedded computer is a reliable and secure gateway for data acquisition and processing at field sites as well as a useful communication platform for many other large-scale deployments. Model DescriptionsThe UC-8100 Series includes the following models:•UC-8131-LX: RISC-based platform with 300 MHz CPU, 2 Ethernet ports, 1 serial port, 8 GB eMMC, SD socket, USB port, and Moxa Industrial Linux pre-installed•UC-8132-LX: RISC-based platform with 300 MHz CPU, mPCIe socket for cellular/Wi-Fi module, 2 Ethernet ports, 2 serial ports, 8 GB eMMC, SD socket, USB port, and Moxa Industrial Linux pre-installed •UC-8162-LX: RISC-based platform with 600 MHz CPU, mPCIe socket for cellular/Wi-Fi module, 2 Ethernet ports, 2 serial ports, 8 GB eMMC, SD socket, USB port, and Moxa Industrial Linux pre-installed •UC-8112-LX: RISC-based platform with 1 GHz CPU, mPCIe socket for cellular/Wi-Fi module, 2 Ethernet ports, 2 serial ports, 8 GB eMMC, SD socket, USB port, and Moxa Industrial Linux pre-installed Package ChecklistBefore deploying the UC-8100 computer, verify that the package contains the following items:•UC-8100 embedded computer•Console cable•Power jack•3-pin terminal block for power (Pre-installed on the UC-8100)•5-pin terminal block for UART x 2 (Pre-installed on the UC-8100)NOTE: Notify your sales representative if any of the above items are missing or damaged. Hardware SpecificationsNOTE The latest specifications for Moxa’s products can be found at https://.Hardware Block Diagram2Hardware Introduction The UC-8100 Series of embedded computers are compact and rugged, making them suitable for industrial applications. The LED indicators allow users to monitor performance and identify trouble spots quickly, and the multiple ports can be used to connect a variety of devices. The UC-8100 Series comes with a reliable and stable hardware platform that lets you devote the bulk of your time to application development. In this chapter, we provide basic information about the embedded computer’s hardware and its various components.The following topics are covered in this chapter:❒Appearance❒LED Indicators❒Default Programmable Button OperationsD iagnosing Device and Subsystem Failures❒Reset to Default Button❒Real Time Clock❒Placement OptionsD IN Rail MountingW all or Cabinet MountingAppearanceFront ViewTop & Bottom ViewsTop BottomDimensions [units: mm (in)]LED IndicatorsRefer to the following table for information about each LED. LED NameColorFunctionUSB Green Steady On USB device is connected and working normally Off USB device is not connected.SDGreen Steady On SD Card inserted and working normally OffSD Card is not detectedPowerGreen Power is on and the computer is working normally. Off Power is off.LAN1/2 (On RJ45 connector)GreenSteady On 100 Mbps Ethernet link Blinking Data transmitting Yellow Steady On 10 Mbps Ethernet link BlinkingData transmittingOff Ethernet is not connectedWireless Signal StrengthGreenYellow Red Number of glowing LEDs indicates signal strength 3 (Green + Yellow + Red): Excellent 2 (Yellow + Red) : Good 1 (Red) : PoorOff Wireless module is not detectedDiagnosis Programmable Green Yellow RedRefer to the section Chapter 3 in Hardware Manual for details. These 3 LEDs are programmable; refer to Chapter 5 in Hardware Manual for details.Default Programmable Button OperationsThe push button is used to diagnose device failure or to perform firmware restoration. After depressing the button, release it at the appropriate time to enter the desired mode to either diagnose your device or restore your device to the default configuration. See below for detailed instructions.The LED indicators behave differently when diagnosing a device failure compared to performing a firmware restoration. See the following table for details. StatusRed LED Yellow LED Green LED Executing diagnostics program Blinking Off On Resetting to default configurationBlinkingBlinkingOnDiagnosing Device and Subsystem FailuresThe red LED will start blinking once you press the push button. Keep the button pressed until the green LED is lit for the first time and then release the button to enter diagnostic mode to check which peripherals are available on the UC-8100-LX. When the diagnostic program is executing, the red LED will be blinking. StatusRed LEDYellow LED Green LED Diagnostics program is executing BlinkingOffOnThe following two tables describe the diagnostics results related to hardware defects and system operation.Hardware DefectsIf you observe any of these hardware issues, contact Moxa for further instructions. StatusRed LED Yellow LED Green LED UART1 device issue On On Off UART2 device issue (except UC-8131) OnOnBlinkingLAN 1 device issue On Off Off LAN 2 device issue On Off Blinking Button device issue On Blinking Off TPM device issue On Blinking Blinking LED device issueOnOffOffSystem OperationIf you observe any of the following issues, check the item indicated by the LEDs. StatusRed LED Yellow LED Green LED CPU usage (over 90%) Blinking On Off RAM usage (over 90%) Off On Off Disk usage (over 90%) Off On Blinking File system corruptedBlinkingOnBlinking0 2478Release the button duringthis time to diagnose Time (s)Release the button during this Button pressedReset to Default ButtonPress and hold the Reset Button continuously for at least 5 seconds to load the factory defaultconfiguration . After the factory default configuration has been loaded, the system will reboot automatically. The Ready LED will blink on and off for the first 5 seconds, and then maintain a steady glow once the system has rebooted.We recommend that you only use this function if the software is not working properly and you want to load factory default settings. The Reset to Default functionality is not designed to hard reboot the UC-8100.Real Time ClockThe UC-8100’s real time clock is powered by a non-rechargeable battery. When the computer is not plugged into a power supply, the battery has an estimated life around 1 year. When the computer is plugged into powersupply, the standby current source will be switch to the power supply. We strongly recommend that you do not replace the battery without help from a qualified Moxa support engineer. If you need to change the battery, contact the Moxa RMA service team.Placement OptionsThere are two sliders on the back of the unit for DIN rail and wall mounting.DIN Rail MountingPull out the bottom slider, latch the unit onto the DIN rail, and push the slider back in.Wall or Cabinet MountingPull out both the top and bottom sliders and align the screws accordingly.Another method for wall mounting installation is to use the optional wall mounting kit. Attach two mounting brackets on the side panel of the computer, and fasten with screws. Install the computer on a wall or cabinet by fastening two screws for each bracket.NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw into one of the keyhole-shaped apertures of the wall mounting plates.3 Hardware Connection DescriptionThis section describes how to connect the UC-8100 to a network and various devices for first time testing purposes.The following topics are covered in this chapter:❒Wiring RequirementsC onnecting the PowerG rounding the Unit❒Connecting to the Console Port❒Connecting to the Network❒Connecting to a Serial Device❒Inserting the SD and SIM Card❒USB Port❒Installing the Cellular/Wi-Fi ModuleWiring RequirementsIn this section, we describe how to connect various devices to the embedded computer. You should heed the following common safety precautions before proceeding with the installation of any electronic device: • Use separate paths to route wiring for power and devices. If power wiring and device wiring paths mustcross, make sure the wires are perpendicular at the intersection point.NOTE: Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.• You can use the type of signal transmitted through a wire to determine which wires should be kept separate.The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together. • Keep input wiring and output wiring separate.• When necessary, it is strongly advised that you label wiring to all devices in the system.Connecting the PowerTerminal BlockThe UC-8100 has a 3-pin terminal block for a 12 to 24 VDC power input.The figure show how the power input interface connects to external power sources. If the power is properly supplied, the Power LED will light up. The Ready LED will glow a solid green color when the operating system is ready (it may take 30 to 60 seconds for the operating system to boot up).Grounding the UnitGrounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.SG: The Shielded Ground (sometimes called Protected Ground) contact is the bottomcontact of the 3-pin power terminal block connector when viewed from the angle shownhere. Connect the SG wire to an appropriate grounded metal surface.Connecting to the Console PortThe UC-8100’s console port is a 4-pin pin-header RS-232 port located on the top panel of the case. It isdesigned for serial console terminals, which are useful for identifying the boot up message, or for debugging when the system cannot boot up.Serial Console Port & Pinouts Serial Console CablePin Signal1 TxD2 RxD3 NC4 GNDConnecting to the NetworkConnect one end of the Ethernet cable to one of the UC-8100’s 10/100M Ethernet ports (8-pin RJ45) and the other end of the cable to the Ethernet network. If the cable is properly connected, the UC-8100 will indicate a valid connection to the Ethernet in the following ways:The LED indicator in the lower right corner glows a solid green color when the cable is properly connected to a 100 Mbps Ethernet network. The LED will flash on and off when Ethernet packets are being transmitted or received. PinSignal1 ETx+2 ETx-3 ERx+4 –5 –6 ERx-7 –8 – The LED indicator in the upper right corner glows a solid orange colorwhen the cable is properly connected to a 10 Mbps Ethernetnetwork. The LED will flash on and off when Ethernet packets arebeing transmitted or received.Connecting to a Serial DeviceUse properly wired serial cables to connect the UC-8100 to serial devices. The serial ports of the UC-8100 use the 5-pin terminal block. The ports can be configured by software for RS-232, RS-422, or 2-wire RS-485. The precise pin assignments are shown in the following table:Terminal BlockRS-232/422/485 PinoutsPin RS-232 RS-422 RS-4851 TXD TXD+– 2RXDTXD-– 3 RTS RXD+ D+ 4CTS RXD- D- 5GNDGNDGNDInserting the SD and SIM CardThe UC-8100 comes with an SD socket for storage expansion, and a SIM card socket that can be installed with a SIM card for cellular communication. The SD card/SIM card sockets are located on the lower part of the front panel. To install them, remove the screw and the protection cover to access the socket, and then plug the SD card and the SIM card into the sockets directly. Remember to push in on the SD card or SIM card first if you want to remove them.USB PortThe UC-8100 provides 1 USB 2.0 full speed port (OHCI), type A connector, which supports a keyboard or mouse, as well as an external flash disk for storing large amounts of data.Installing the Cellular/Wi-Fi ModuleThe UC-8100 provides an mPCIe socket for installing a cellular/Wi-Fi socket. Follow these steps:1.Remove the screws on the side panel, and take off the cover.2.Find the location of the PCIe socket. Insert the cellular module into the socket, and then tighten the screwsto fasten the socket.3.Next, you need to install the antenna cable. There are two antenna connectors on the cellular module.Connect the cable to either connector.4. Plug the other end of the cable into the connector on the front panel of the UC-8100. Remove the blackplastic cover first.5. Install the connector; place the locking washer first, and then tighten the nut.6. Connect the antenna to the connector.ARegulatory Approval StatementsThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Class A: FCC Warning! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense.European Community。

● 警告标识■安全注意事项不得让金属物体、导线或安装时产生的切屑或湿气进入控制器、调试工具端口或调试工具电缆连接器的引脚上。

否则会导致触电、短路或机器误动作。

通电期间，请勿触摸端子，否则会因触电而导致轻伤。

请勿在有爆炸性气体和可燃性气体的环境中使用，否则会由于爆炸而造成轻度的伤害。

请勿分解、改装、修理，或者接触设备内部，否则会导致轻度的触电、火灾、设备故障。

本设备作为开放性的处理控制器，请勿在可能起火的控制柜内使用。

使用2个以上断路开关时，在修理检查前，请关闭所有开关，使产品处于不通电状态。

如果在超过产品寿命的状态下使用，可能导致接点熔化或烧损。

输出继电器的寿命根据开关容量和开关条件有很大的差异。

因此必须考虑实际使用条件，在额定负载、电气寿命次数内使用。

●采用贴片LED合成数码管面板，LED灯直接贴片在控制器PCB主板上（老款控制器采购LED数码管厂家的插件数码管），不但减少了成本，更自主把控LED的品质。

● 0.25测量精度达级，进一步升级了分辨率，测量更加精准稳定。

● AiFUZZY FUZZY PID人工智能调节算法，将模糊控制和自适应控制完美结合，带自整定和自学习功能，能在调节中自动学习和记忆被控对象部分特征以使效果最优化。

具有无超调及无欠调的控制特性，对复杂难控对象也能获得优良的控制效果等特点。

●支持多种热电偶、热电阻输入，通过参数设置可自由切换选择。

● SSR支持多种输出规格：继电器触点开关、固态继电器驱动电压、可控硅无触点开关。

●具备无小数点和一位小数点选择及摄氏度和华氏度选择设置功能。

●进一步提升了抗干扰性能，使得在更恶劣的电磁干扰环境中也能稳定工作。

● 采用高性能开关电源设计，带载能力强，选用宽温度范围、高内压元器件，以适应各种不同恶劣环境，具备防雷击浪涌设计，自恢复保险电路，过压或欠电压自动断电保护，电压正常后自动恢复正常供电。

●本型号定位：专为机械设备提供一种功能简单、价格经济、性能稳定、控制精准的温度控制器。

Eaton EPCT Firere pump controllersT ouchscreen based electric fiProduct DescriptionThe EPCT Fire features an advanced, 7” color touchscreen that incorporates both the fire pump controller (FPC) and automatic transfer switch (ATS) functionality into one, intuitive display. Designed solely with the consumer in mind, the EPCT Fireenables technicians to commission the fire pump controller faster; troubleshooting is made easier and is more effective through the use on-screen history filtering and diagnostic monitoring.All full-service fire pump controllers can be offered in either full-voltage or reduced voltages starting methods:• FD/FT20 - Limited service• FD/FT30 - Across-the-line• FD/FT40 - Part winding• FD/FT50 - Primary resistor• FD/FT60 - Autotransformer• FD/FT70 - WYE-Delta (Star-Delta) open transition• FD/FT80 - WYE-Delta (Star-Delta) closed transition• FD/FT90 - Soft startProduct FeaturesT ouchscreen DisplayGeneralSpeed of commissioning, configuration and troubleshooting are more critical to businesses today more than ever. Through theuse of a 7” touchscreen, users can easily program all site specific setpoints through an intuitive menu structure, view all critical system information, and troubleshoot quickly and accurately via on-screen diagnostics.Automatic Transfer Switch IntegrationGoing away from the multiple screen approach, the EPCT Fire touchscreen integrates both the Fire Pump Controller and Automatic Transfer Switch into one display enabling the user to effectively manage programming and operation from one source. Commissioning SimplifiedThe Startup tab features all controller related commissioning tasks such as: Quick Setup, Setup Phase Reversal, Flow Test, Manual/ Automatic Starts, and Test Alarms.UL Type RatingThe touchscreen display has been tested in accordance with UL and achieves a type 4X rating.Programming MenuStartup tabThis tab system enables the user to complete all controller related commissioning tasks. Each sub-menu within the Startup tab guides the user through step-by-step, intuitive screens to quickly and effec-tively complete the startup and commissioning process.Panel Setup tabAll variables relating to the panel, such as language, date and time, nominal voltage, etc., are located in the Panel Setup tab. For all programming points within the Panel Setup tab, refer to the instruc-tion manual: MN124016EN.Help tabThe help tab provides end users service contact information from the company that commissioned the unit (if programmed), factory contact information, and a QR code to download the instruction manual onto a mobile device.Pressure Settings tabContains a variety of pressure settings that may be programmed to suit site requirements. Some key settings include: Start Pressure, Stop Pressure, Low Pressure Alarm, High Pressure Alarm, Low Suction Shutdown, Low Foam Shutdown, Pressure Units, and the ability to calibrate the transducer.Timer Values tabThis tab system contains the programming point for all fire pump controller related timers. These timers are: Minimum Run Time, Acceleration Time, Sequential Start Time, Fail to Start Time, Fail to Stop Time, and Weekly Motor Test Timer.ATS Settings tab (if equipped)The ATS Settings tab will only be enabled on units equipped with an automatic transfer switch. Programming points within this tab only pertain to the operation of the transfer switch.Alarm Setpoints tabThere are seven (7) programmable alarm points within this tab system: Phase Reversal, Phase Failure Alarm Setpoint, Motor Overload Setpoint, Transducer Fail Pump Start, Abort Motor Test on Low Voltage, Voltage Alarm Settings, and Frequency Alarm Settings. Inputs/Outputs tabThe I/O board is capable of accepting ten (10) custom inputs that can be programmed for seventeen (17) predefined conditions. The output relays can be programmed for sixty-one (61) separate condi-tions. Additional relays can be added through the use of a single or multiple optional relay boards.History/Statistics/Diagnostics tabThis tab system allows the customer/technician to view historical data, controller statistics, controller diagnostics, and startup informa-tion. To assist, the controller can filter for specific events or between certain dates to speed up troubleshooting.I/O BoardPower SupplyThe redesigned I/O board is equipped with a full voltage power supply capable of accepting voltage inputs between 200-600VAC three phase, or 240VAC single phase.Customer Input ConnectionsConnection terminals are provided at the top of the I/O board for external customer connections that can be programmed through the touchscreen display.Output RelaysThe I/O board features four (4), 250VAC, 8A, 2 Form-C relays desig-nated for the following: Common Alarm, Power/Phase Failure, Phase Reversal, and Pump Run. Each relay socket has a surface mount LED to indicate the relay’s coil status.Optional BoardsThe controller can accept up to four (4) additional option boards: optional relay board, MODBUS communication board, secondary4-20mA device board, and an alarm board. The controller has provi-sions to allow future optional boards to be added with plug-and-play functionality.Other ComponentsDrain Valve SolenoidAll full-service EPCT Fire controllers are equipped with a drain valvesolenoid used for manual or automatic motor tests.External USB PortThe USB port allows the user to download historical messages,statistics, diagnostic information, startup file, and current controllerconfiguration to any USB device with FAT16 or FAT 32 formatting.EnclosuresThe EPCT Fire controllers come standard with UL type 2 (drip-proof)enclosures. Optional enclosures are available and include: type, 3, 3R, 4, 4X, and 12.Emergency Start Operator A mechanically operated emergency start handle (ESH) will mechani-cally activate the motor contactor(s) independently from any electri-cal control circuits.Standards & Certifi cations All EPCT Fire full-service, electric fire pump controllers meet or exceed the requirements of Underwriters Laboratories and Underwriters Laboratories Canada [UL218 and UL1008], Factory Mutual, the Canadian Standards Association, New Y ork City building code, CE mark, U.B.C./C.B.C. seismic requirements, and are built to the latest edition of NFPA 20 standards. The EPCT Fire electric fire pump controllers are suitbale for use as service entrance equipment- does not meet CEC requirements for Canada.Display ScreensHome tab - without ATSHome tab - with ATS Common Alarm SettingsNotification Area Settings Message History Customer Service ContactFollow us on social media to get thelatest product and support information.Eaton is a registered trademark. All other trademarks are property of their respective owners.Eaton1000 Eaton BoulevardCleveland, OH 44122United StatesElectrical SectorCanadian Operations5050 MainwayBurlington, ON L7L 5Z1CanadaEatonCanada.ca© 2018 EatonAll Rights ReservedPrinted in CanadaPublication No. BR124053EN / 001January 2018Motor HPL ine voltage Withstand rating Standard Interm ediate High 5 - 40200 - 208V 100,000150,000200,000315 (143)5 - 50220 - 240V 5 - 75380 - 415V 5 - 100440 - 480V 5 - 100550 - 600V 25,000100,000Approxim ate weight L bs. (K g)14.00 [356]45.75 [1162]12.00 [305] 6.00 [152]5.25 [133]3.38 [86]38.25 [972]70.00 [1778]58.00 [1473]12.00 [305]5.00 [127]9.92 [252]Ø1.75 [Ø44]3.32 [84]29.28 [744]1.12 [28]PIPING ENTRANCE 1/2" NPT - FEMALE 1.17 [30]123456784.24 [108]2.84 [72] 3.29 [84]7.69 [195]PIPING ENTRANCE 1/2" NPT - FEMALE 1 - EPCT TOUCHSCREEN2 - EXTERNAL USB PORT3 - SOURCE 1 POWER SWITCH4 - SOURCE 2 POWER SWITCH5 - START PUSHBUTTON6 - STOP PUSHBUTTON7 - MSH (EMERGENCY START HANDLE)8 - RECOMMENDED CABLE ACCESS (BOTTOM ONLY)9 - LOCKABLE QUARTER-TURN10 - STANDARD QUARTER-TURNNOTES:1 - DIMENSIONS: in [mm]2 - ALL ENCLOSURES FINISHED IN RED3 - STANDARD ENCLOSURE: TYPE (NEMA) 210910Line Voltage200-208220-240380-415440-480575-600Line Lugs (QTY.) & Cable Size per Ø Service Ground Lugs (QTY.) & Cable Size per ØMax HP 2530406075(1) #14 - 1/0 (CU/AL)(1) #14 - 2/0 (CU/AL)405075100100(1) #4 - 4/0 (CU)(1) #4 - 350MCM (CU/AL)7575150200200(1) #3 - 350MCM (CU/AL)(1) #4 - 350MCM (CU/AL)100125200250300(2) 3/0 - 350MCM (CU/AL)(2) 1/0 - 750MCM (CU/AL)150200300400500(2) 250 - 350MCM (CU/AL)(2) 1/0 - 750MCM (CU/AL)250300500600700(4) 4/0 - 500MCM (CU/AL)(2) 1/0 - 750MCM (CU/AL)Line Voltage200-208220-240380-415440-480575-600Single Run Cable Sizes Double Run Cable Sizes Max HP 1520304050#14 - #8 (CU/AL)-405075100100#14 - #1 (CU/AL)-75100150200150#8 - 3/0 (CU/AL)-150150250300300#2 - 750MCM (CU/AL)1/0 - 250MCM (CU/AL)2503005006007001/0 - 500MCM (CU/AL)1/0 - 500MCM (CU/AL)For ambient temperatures exceeding 30C (86F), the temperature rating of motor conductors is recommended to be a minimum of 90C (194F)For proper cable size, refer to the National Electric Code (NEC - NFPA70)Line Terminals ConnectionsLoad Terminals ConnectionsEaton is a registered trademark.All other trademarks are property of their respective owners.EatonCanadian Operations5050 MainwayBurlington, ON L7L 5Z1P: 1-877-860-7955E-mail:*********************Web: © 2019 Eaton All Rights Reserved Printed in Canada Publication No. PS124001EN / 001Article No. XXXXXX February 2019EPCT Fire option selection matrixEPCT Fire electric fi re pump controllers Typical specifications1. ApprovalsA. The Fire Pump Controller shall meet therequirements of the latest edition of NFPA 20 andshall be listed by [Underwriters Laboratories (UL)]and approved by [Factory Mutual Research (FM)][Canadian Standards Association (CSA)] [New Y orkDepartment of Buildings (NYSB)] and carry the CEmarking for fire pump service.2. Starting typeA. The controller shall be of the combined manual andautomatic type designed for [Limited Service - 1Por 3P] [Full Voltage Starting] [Part Winding Starting][Primary Resistor Starting] [AutotransformerStarting] [Wye-Delta (Star-Delta) Open TransitionStarting] [Wye-Delta (Star-Delta) Closed TransitionStarting] [Solid State Soft Start Starting]3. R atingsA. The Controller shall have a withstand rating of100,000 RMS symmetrical amperes @ [208V][240V] [380V] [400V] [415V] [480V] [25,000@ 600VAC].B. Temperature:4 to +50 deg. C (39 to +122 deg. F)4. ConstructionA. The controller shall include a motor ratedcombination isolating switch and circuit breaker,mechanically interlocked and operated with asingle externally mounted handle.B. The isolating switch shall be rated to disconnectthe motor load.C. The isolating switch/circuit breaker combinationshall be mechanically interlocked such that theenclosure door cannot be opened when the handleis in the on position except by a tool operateddefeater mechanism.D. The controller manufacturer shall manufacturethe contactor, isolating switch, circuit breaker,pushbuttons, and enclosures. Brand-labeledcomponents will not be accepted.5. EnclosureA. The controller shall be housed in aType 2 (IEC IP11) drip-proof, powder baked finish,freestanding enclosure.B. Optional enclosures:1. Type 3R (IEC IP14) rain-tight enclosure2. Type 3 (IEC IP55) water-resistant enclosure3. Type 4 (IEC IP66) watertight enclosure4. Type 4X (IEC IP66) watertight 304 stainlesssteel enclosure5. Type 4X (IEC IP66) watertight 316 stainlesssteel enclosure6. Type 4X (IEC IP66) watertight corrosionresistant enclosure7. Type 12 (IEC IP52) dust-tight enclosure6. Microprocessor controlA. The controller shall come complete with a 7”,800x480, color touchscreen. The touchscreen shallbe type 4X rated.1. Home tab capable of displaying system pres-sure, three phase voltage and amperagereadings for both sources, system frequency,date, and time, configurable notifications in thenotification area, displaying current start andstop set points, and visual representation ofthe transfer switch position, source 2 discon-nect handle, and contactor.2. Virtual buttons to manually test the pumpmotor and/or the backup power supply engine.3. Controller statistics screen, including:A. Total Powered TimeB. Total Motor Run TimeC. Last Motor Run TimeD. Calls to StartE. Motor StartsF. Maximum Starting Current AG. Maximum Starting Current BH. Maximum Starting Current CI. Maximum Run Current AJ. Maximum Run Current BK. Maximum Run Current CL. Last LR Current AM. Last LR Current BN. Last LR Current CO. Minimum System PressureP. Maximum System PressureQ. Minimum S1 Voltage ABR. Minimum S1 Voltage BCS. Minimum S1 Voltage CAT. Maximum S1 Voltage ABU. Maximum S1 Voltage BCV. Maximum S1 Voltage CAW. Minimum S2 Voltage ABX. Minimum S2 Voltage BCY. Minimum S2 Voltage CAZ. Maximum S2 Voltage ABAA. Maximum S2 Voltage BCAB. Maximum S2 Voltage CAAC. Minimum S1 FrequencyAD. Maximum S1 FrequencyAE. Minimum S2 FrequencyAF. Maximum S2 FrequencyAG. Last System StartupAH. Last Motor StartAI. Last Low Pressure StartAJ. Last Locked Rotor TripAK. Last S1 Phase FailureAL. Last S2 Phase FailureAM. Last S1 Phase ReversalAN. Last S2 Phase ReversalAO. Last S1 UndervoltageAP. Last S1 OvervoltageAQ. Last S2 UndervoltageAR. Last S2 OvervoltageAS. Last S1 Under FrequencyAT. Last S1 Over FrequencyAU. Last S2 Under FrequencyAV. Last S2 Over FrequencyAW. Last Generator StartAX. Last Generator StopAY. Last transfer to S1AZ. Last transfer to S2BA. Last S2 Disconnect4. Controller diagnostics screen, including:A. Controller Serial NumberB. Logic Board Firmware VersionC. I/O Board Firmware VersionD. I/O Board Supply VoltageE. I/O Board CommunicationF. CT1 Secondary AmperageG. CT2 Secondary AmperageH. CT3 Secondary AmperageI. Transducer Input VoltageJ. Transducer Output CurrentK. Transducer Setpoint Current 2L. Transducer Setpoint Current 1M. All Input Status (Open or Closed) (Can beselected to override for one minute and manu-ally change the state of the input)N. All Output Relay Status (Energized orDe-energized) (Can be selected to overridefor one minute and manually energize orde-energize the relay)O. Test the display board’s communication.5. Archive message screen that will display up to65,000 alarms/messages stored in the controllers’memoryB. The microprocessor logic board shall be avail-able with a USB port for transference of messagehistory, controller status, diagnostics, startup andstatistic files and the ability to update firmware.C. A Fail-to-Start alarm shall occur if the motor controllersees less than 20% of the motor full load amps afteran adjustable time delay of 1-99 seconds.D. Locked rotor protection shall be provided. After a tripcondition and restoration of power, the display shallindicate the voltage, current, and date and time atthe moment that the controller tripped.E. A sequential start timer and weekly test timer shallbe provided as standard.F. A restart time delay of one (1) second shall beprovided to allow the residual voltage of the motor todecay prior to re-starting the motor. In the event thatthe pump motor continues to run after a request tostop, then the controller must display a fail to stopmessage to indicate this condition.G. Overvoltage (0-100%) and undervoltage (0-100%)sensing and alarming shall be provided as standard.H. The controller shall be supplied with interlock andshutdown circuits as standard. A green LED inthe notification area shall indicate an interlock oncondition.I. Where shutdown of the pump(s) due to low suctionpressure is required, it shall be accomplished withoutthe addition of a separate panel or enclosure.The display shall indicate low suction shutdown.Resetting of the condition shall be automatic ormanual as selected by the user.7. Programming MenuA. The programming menu shall have the ability toenable an entry password.B. The controller shall have nine (9) languages as a stan-dard: English, French, Spanish, Portuguese, Turkish,Italian, Dutch, Chinese, and Polish.C. The programming menu shall be grouped into ten(10) tabs as follows:1. Home2. Startup3. Panel Setup4. Help5. Pressure Settings6. Timer ValuesFire pump controllersFeaturesii EPCT FIRE ELECTRIC FIRE PUMP CONTROLLERS PS124004EN February 2019 Eaton is a registered trademark.All other trademarks are property of their respective owners.EatonCanadian Operations5050 MainwayBurlington, ON L7L 5Z1P: 1-877-860-7955E-mail:*********************Web: © 2019 Eaton All Rights Reserved Printed in Canada Publication No. PS124004EN / 001Article No. XXXXXX February 20197. ATS Settings8. Alarm Setpoints9. Inputs/Outputs10. History/Statistics/Diagnostics8. Pressure sensor A. A solid-state 4-20mA pressure sensor shall beprovided. The pressure Start and Stop points shall be adjustable in increments of one (1) PSI.9. Custom inputs/outputsA. The controller shall come standard with ten(10) programmable inputs, four (4) programmed outputs with the ability to add up to another sixteen(16) outputs via optional relay boards.B. The user shall be able to program the inputs/outputs through the main programming menu.C. The inputs shall be selectable based on the following criteria:1. User selected message or seventeen (17) predetermined messages2. Link to a future relay and/or LED indicator3. Alarm latched until reset4. Normally open or closed input5. On and/or off-delay timerD. The future relays shall be selectable based on the following criteria:1. Output based on a minimum of sixty-one (61) predetermined alarms, controller status or a custom input2. Latched until reset3. Energized under normal conditions4. On and/or off delay timer on the output10. Alarm relaysA. All relays shall be soldered on the PCB. An LED on the relay panel shall indicate the energized state of the relay. All relay contacts shall be rated @ 8A, 277VAC/30VDC. Two (2) sets of Form-C contacts shall be provided for each of the following:1. Common Alarm2. Power/Phase Failure3. Phase Reversal4. Pump RunB. The Common Alarm and Power/Phase Failure relays shall be energized under normal conditions.11. Audible alarm buzzerAn audible alarm buzzer, capable of being heardwhile the motor is operating, shall operate if Fail to Start, Hardware Malfunction or any Common Alarm condition exists.12. Manufacturer A. The controller shall be of the EPCT Fire type asmanufactured by Eaton Corporation.Fire pump controllers Features。

E2T Infrared Flare MonitorsE2T Quasar 8100 Series Pilot andFlared Gas Monitorss Flame detection up to 400 ms Detection of hydrocarbon as well as hydrogen flamess CSA/US and ATEX explosion-proof housings Safety and environmental protections Automatic gain control for adverse weather conditionss High quality sight-through opticss On-board alarm set point relays Modular opto-electronic package for easy removal from housings IR pyrometer and amplification circuitry in one single moduleMonitoring and detection instruments, designed for continuous duty monitoring of flameThe E2T Quasar 8100 series are monitoring and detection instru-ments designed for continuous duty monitoring of pilot flame (type PM) and flared gases (type FM) fromflares.A sight-through optical systemand selection of various spot sizes enables the E2T QUASAR M8100-EXP to be positioned as far as 1/4 mile (400 m) from the stack being monitored. Alignment on the target is accomplished through superb sightthrough optics and an M-3 swivel mount.Custom electronics adapt to target movement, varying luminosity and most climate conditions. The alarm delay circuit can be adjusted fora specific location or application, eliminating false alarms from tempo-rary loss of signal due to intermit-tent flames, adverse weather and wind.The system is complete with internalcooling base, air purge tube andswivel mount. An optional pedestalstand allows for easy mounting.Pilot and FlaresContinuous monitoring of pilotflames and flared gases is critical toensure that the gases will be ignitedand to confirm compliance withgovernment-set pilot status recor-ding requirements. Thermocouplefailure, flame movement, varyingluminosity and adverse climaticconditions are just a few of theobstacles which have to be overcometo gain long-term monitoring relia-bility without false alarms.Typical Applications:s Elevated Flareso Steam Assistedo Air Assistedo Gas Assisteds Ground Flareso Burn Pit Flareso Multi point/Staged Multipoint flaress Off-Shore FlaresLumaSense TechnologiesTemperature and Gas Sensing SolutionsLumaSense Technologies, Inc., reserves the right to change the information in this publication at any time.*********************©2012 LumaSense Technologies. All rights reserved.Quasar-8100_Datasheet-EN Rev 06/13/12North AmericaSales & Service Santa Clara, CATel: +1 800 631 0176Fax: +1 408 727 1677LumaSense Technologies Benelux B.V . (Other Than North America)E 2T Products Sales & ServicePavana 2, 4711 VG Sint Willebrord, Netherlands Tel: +31 165 381 800 Fax: +31 165 389 012High quality optics:5 different optics are available to ensure the highest flame signal detection.Heavy duty accessories:For easy mounting, alignment and focusing on the target, a heavy duty swivel mount with locking and adjusting capability is included. The M-3 swivel mount is secured on an optional pedestal mount (M-8), a steel pipe assembly with a bolt down plate to secure the M-8 to a foundation. The AP-2S Air purge tube is designed for high rain water diversion from the systems optics.At higher ambient temperatures, the water cooling cavitybuilt into the underside of the explosion-proof enclosure can be used or a Vortexair cooler for temperature reduction up to 27 °F (3 °C) can be installed to the water cooling cavity.Easy maintenance or replacement, also from older modules:The heart of the system is the M8100-EXP , non-contact infrared electro-optical package which can be removed from the explosion proof housing for repairs or replacement, leaving intact all wiring and alignment of system.AmbientTemperature Limits: Explosion-Proof Certification:-40 to 125°F (-40 to 52°C) or -40 to 212°F (-40 to 100°C) with integrated water cooling baseCSA/US: Class 1, Division 1, Groups C and D Class 1, Division 2, Groups A through D, T4 CENELEC: EExd IIB T4Powerrequirements:Available in 115 VAC or 230 VAC or 24 VDC (Voltages +/- 10%) 115 Watts6 882 400 Vortec air cooler6 882 100M-3, Heavy duty swivel mount6 882 120 M-8, Pedestal Base 6 882 650AP-2S, air purge tubeReference Numbers。