托莱斯科技光合有效辐射智能传感器技术说明书

一、功能和用途
EL10全数字光照度传感器使用高精度光电传感器，是艾贝斯专为ETW/ETH时控器及FAC4开发的一款高精度光照强度采集设备。

广泛应用于需要获得光照的强度的设备。

如路灯控制设备，产矿照明间控设备等。

其具有标准RS485输出接口，方便自由扩展。

图一、产品外观图
二、技术参数
输入电压：9-35VDC
设备功耗：<1W
输出接口：RS485
工作温度：-10-55°C
量程：0~1000Lux/10~10000Lux可选。

测量精度：<7%
通信速率：9600bps
体积：L110*W85*H40（mm）
重量：130g
安装方式：壁挂式/螺丝固定
三、使用说明
1、RS485通信
EL10全数字光照度传感器具有数字量输出接口，系统采用工业级RS485通信协议进行传输数据。

仅需接通AB信号线及系统电源线即可以使用。

四、外部接线说明
A/B:RS485通信总线
AIN：模拟量输出
GND：电源地
VCC：直流电源正极
五、注意事项
1、由于防水等级不高，请不要置于雨水可以淋到的地方。

2、两级档位出厂前已固定。

3、由于模拟量接收信号干扰较大，请不要远距离使用模拟量的方式。

传感器录井传感器是综合录井仪最基础的部分，其工作性能的好坏直接影响着录井质量。

录井传感器可分为绞车传感器、泵冲传感器、转盘转速传感器、悬重传感器、立管压力传感器、套管压力传感器、扭矩传感器、温度传感器、密度传感器、电导率传感器、体积传感器、流量传感器、硫化氢传感器等。

一、绞车传感器1、工作原理绞车传感器安装在绞车轴上，可以监测整个钻进过程中绞车轴转动所产生的角位移。

通过计算就可以得到钻进过程中大钩的高度变化，从而得到当前的钻井深度。

传感器内部装有两只光电开关，并配有一片带齿片的遮光片，当遮光片随绞车轴转动时，分别阻断或导通传感器内两只光电开关间隙中的红外光线，从而发出两组相应的电脉冲信号，此信号送入仪器经识别处理后就可以得到相应的角位移方向和变化值。

2、技术指标工作电压： 3-12V （DC）；推荐工作电压 5V（DC）输出电平：高电平≥4.3V；低电平≤0.5V(5V供电时)。

工作温度：–40℃～80℃功耗： 30mw响应时间：150μS3、安装和使用引出脚接线规定传感器为4线制，分别定义为：红色 +5V；黑色 0V；蓝色信号A；黄色信号B。

安装操作步骤绞车传感器安装在绞车轴上，滚筒轴两端均可安装，但输出相位的位序相反，为正确确定转轴方向，接收仪器有相应的倒向开关，传感器外壳可靠接地。

安装时，卸下滚筒轴端面的护罩及导气龙头的气动接头，先将传感器安装牢固，再把气动接头装上，用绞车皮带将传感器的外壳固定牢固后，装上护罩，最后将电缆线接至接收仪器。

4、一般故障判断及排除如绞车传感器在绞车轴旋转过程中，无信号输出，即两路脉冲或一路脉冲信号出故障，首先应检查加长电缆的断线或损坏。

如怀疑绞车传感器出故障，在通电情况下缓慢转动绞车传感器轴，同时用万用表直流电压挡分别测量传感器的信号A脚和B脚输出的电压，如果绞车传感器工作正常，输出电压为高电平≥4.3V；低电平≤0.5V。

5、维护保养采取防水、防污染等外部防护措施以提高其寿命和可靠性。

专业经营各类实验仪器、科研仪器设备总辐射传感器总辐射传感器是就是感应测量辐射的仪器，今天小编来为大家介绍的是南京欧煕科贸经营销售的总辐射传感器。

具体了解一下产品的参数情况，如有需要，欢迎联系。

总辐射传感器，气象站传感器，进口传感器，进口气象站，德国LAMBRECHT总辐射传感器，进口总辐射传感器总辐射传感器主要用来测量波长范围为0.3～3微米的太阳总辐射。

由双层石英玻璃罩、感应元件、遮光板、表体、干燥剂等部分组成。

广泛应用于气象探测、大气环境监测、气候观测、太阳能利用、农业、建筑物。

总辐射传感器技术参数专业经营各类实验仪器、科研仪器设备南京欧熙科贸有限公司专业经营各类实验仪器、科研仪器设备，代理各大国际知名品牌仪器，如日本PREDE全自动太阳光度计、天空成像仪、太阳跟踪系统、德国Lambrecht气象站、风速风向传感器、光照传感器、辐射传感器、美国RSA有氧厌氧呼吸仪/活性污泥呼吸仪/微生物降解呼吸仪/海水淡化呼吸仪、德国HS ENGINEERS电磁海流计、保加利亚milkscope牛奶分析仪、德国Avisoft Bioacoustics动物声谱分析仪、声波录制仪、西班牙Marine InstrumentsMLi卫星追踪表层漂流浮标、法国THALOS渔用浮标、澳大利亚 Next Instruments 近红外谷物分析仪、法国GBX水分活度仪、美国FTC 质构仪、美国National揉混仪/和面仪/酵母活性产气率测定仪、意大利ALVIM生物膜系统等，服务于环境，气象、交通、海洋、食品，生命科学、工业、制药以及商业实验室等众多领域。

公司本身以高校及企事业科研院所的技术力量为依托，具备了扎实的专业基础和丰富的实践经验。

如果您对我们的产品感兴趣，欢迎咨询南京欧熙科贸有限公司/，真诚期待与您的合作!。

344Q45系列传感器Q 45 S e r i e s •Email: sensors@345 Q45系列传感器Q45系列对于Q45系列传感器：i) 在电缆接线方式的型号后加上“W/30”即为9m电缆型号，如Q45BB6F W/30 ii) 接插件式产品需另配电缆。

346Q45系列传感器Q 45 S e r i e s对于Q45系列传感器：i) 在电缆接线方式的型号后加上“W/30”即为9m 电缆型号，如Q45BB6F W/30ii) 接插件式产品需另配电缆。

•Email: sensors@347 Q45系列传感器Q45系列对于Q45系列传感器：i) 在电缆接线方式的型号后加上“W/30”即为9m电缆型号，如Q45BW13F W/30 ii) 接插件式产品需另配电缆。

349Q45系列注：LEXAN 为GE 公司的注册商标350Q 45 S e r i e s电缆式接插件式4针Mini 型系列或4针Euro系列Q456E 发射器（电缆式）Q456EQ 或Q456EQ54针Mini 型系列或4针Euro系列“Q ”型号后缀4针Mini 型出线图“Q5”型号后缀4针Euro 型出线图接插件式说明：Q45BB6直流传感器带2米或9米PVC 电缆，或4针Mini 型或4针Euro 型接插件电缆。

直流4针Mini 型QD 传感器后缀是“Q ”，直流4针Euro 型后缀是“Q5”。

接插件式Q45BB6配用电缆请看附件部分。

351Q45系列注：LEXAN 为GE 公司的注册商标352Q 45 S e r i e s电缆式接插件式5针Mini 型出线图5针Euro 型出线图接插件式说明：Q45BB6直流激光反射板式传感器带2米或9米PVC 电缆，或5针Mini 型或5针Euro 型接插件直流5芯Mini 型QD 传感器后缀是“Q ”，直流5针Euro 型QD 传感器，其后缀是Q6，Q45BB6反射板式激光传感器配用电缆请看附件部分。

智能农业设备说明书一、产品概述智能农业设备是基于现代科技和先进的信息技术开发的一款致力于提高农业生产效率的设备。

本设备旨在帮助农民更加科学地管理农作物和养殖业务，实现可持续发展和资源优化利用。

二、产品特点1.智能化管理：本设备配备了先进的传感器和控制系统，能够自动感知和监测农作物的生长环境，并根据实时数据进行精准的调节和管理，提供最佳的生长条件。

2.自动化控制：用户可以通过智能手机或电脑终端对设备进行远程控制，实现自动浇灌、施肥、除草等操作，节省人力和精力。

3.数据分析：设备能够收集和分析大量的农业数据，提供详尽的农作物生长情况、土壤质量和气候变化等信息，为农民提供科学依据和决策支持。

4.节能环保：本设备采用节能技术，能够有效减少能源消耗，并且优化土壤肥力管理，降低对环境的负面影响。

5.易于操作：设备配备了友好的界面和操作指南，即使对于没有农业经验的用户也能轻松掌握使用方法。

三、产品组成及功能1.传感器系统：设备配备了多种传感器，包括温度传感器、湿度传感器、光照传感器等，能够实时感知农作物所处环境的变化。

2.控制系统：设备通过自动控制系统对传感器收集的数据进行分析，判断并调控灌溉、施肥、温度等参数，提供最佳的生长环境。

3.移动终端APP：用户可以通过手机APP远程监控和控制设备运行状态，实现无人值守和智能化管理。

4.数据分析软件：设备将采集的数据存储在云端，并提供专业的数据分析软件，用户可以通过软件了解农作物的生长情况、需求和预测等。

5.智能报警系统：设备配备了智能报警系统，一旦设备出现异常或环境参数超过预设范围，系统将及时发出警报提醒用户。

四、使用方法1.安装设备：根据提供的安装指南，将设备正确安装在田地或养殖场地。

2.连接电源：将设备连接到电源，并确保正常供电。

3.下载APP：根据提供的二维码或应用商店链接，下载并安装设备对应的手机APP。

4.连接设备：打开APP，在设备管理界面中添加新设备，并按照指引将设备与手机进行连接。

BLUE LASER25303D SMART LASER LINE PROFILE SENSORGocator 2530 continues the signature high speed 3D blue laser profiling and compact design of the 2500 series, with a wider field of view. This sensor is ideal for battery and consumer electronics inspection, and applications in rubber & tire scanning and factory automation.Gocator 2530 line profilers achieve inspection speeds up to10 kHz, at high resolutions and fields of view up to 100 mm. The custom 2 MP high-speed imager, advanced optical design, and blue laser light allow the 2530 to generate excellent 3D data with highly repeatable results on both shiny and low contrast surfaces.INSPECT WITH SPEED AND PRECISIONT ake advantage of higher speeds by enabling multiple exposures to measure specular and low contrast surfaces simultaneously (e.g., shiny metal of battery cells, cellphone midplates, rubber). The sensor’s speed is also akey advantage in achieving high Y resolution (spacing in direction of travel). Submillimeter X and Z resolutions deliver detailed inspection of small assembly features such as edges or gaps and accurate 3D height measurement of surface geometry and defects (such as scratches and pits).WIDER FIELD OF VIEW AND LARGER MEASUREMENT RANGEThe 2530’s wider field of view allows engineers to scan complete targets with a single sensor (e.g., cell phone midplate). Large field of view and measurement range allow the sensor to handle a wider variety of scan targets.EASY INTEGRA TION INTO TIGHT SPACES AND EXISTING SYSTEMSThe Gocator 2530 has one of the smallest footprints in the industry while maintaining an IP67 rating. This allows the sensor to be mounted in virtually any machine environment.• UP TO 100 MM FIELD OF VIEW• 28 MICRONS X RESOLUTION• 0.5 MICRONS Z REPEAT ABILITY• 10,000 PROFILES PER SECOND INCLUDING 3D MEASUREMENT• SETUP & CONTROL VIA WEB BROWSER OR SDK• BUIL T-IN TOOLS, NO PROGRAMMING• EXTEND WITH GDK AND GOMAXTire sidewall uniformity inspectionGocator® 2530 inspecting battery weldCell phone midplate inspectionAMERICASLMI T echnologies Inc. Burnaby, BC, Canada EMEARLMI T echnologies GmbHT eltow/Berlin, GermanyASIA PACIFICLMI (Shanghai) Trading Co., Ltd.Shanghai, ChinaLMI T echnologies has sales offices and distributors worldwide. All contact information is listed at /contactDATASHEET_Gocator_2530_US-1.1©2020 LMI T echnologies Inc. All rights reserved. Subject to change without notice.。

光照度传感器的工作原理及使用方法
光照度传感器的工作原理及使用方法
光照度传感器的工作原理
不同角度光线透过余弦修正器汇聚到感光区域、汇聚到感光区域的太阳光通过蓝色和
黄色进口滤光片过滤掉可见光以外的光线; 透过滤光片的可见光照射到进口光敏二极管，光敏二极管根据可见光照度大小转换成电信号，电信号进入单片机系统，单片机系统根据
温度感应电路，将采集到的光电信号进行温度补偿，以输出精准的线性电信号。

为了提
高变送器的精度和分辨能力，我们采用了独特地专利技术，双通道信号输出，分别是KLUX 级信号和LUX 级信号。

光照度传感器的使用方法
光照度传感器应安装在四周空旷，感应面以上没有任何障碍物的地方。

然后将辐射表
电缆插头正对北方，调整好水平位置，将其牢牢固定，再将总辐射表输出电缆与记录器相
连接，即可观测。

最好将电缆牢固地固定在安装架上，以减少断裂或在有风天发生间歇中
断现象。

艾驰商城是国内最专业的MRO 工业品网购平台，正品现货、优势价格、迅捷配送，是一站式采购的工业品商城！具有 10年工业用品电子商务领域研究，以强大的信息通道建
设的优势，以及依托线下贸易交易市场在工业用品行业上游供应链的整合能力，为广大的
用户提供了传感器、图尔克传感器、变频器、断路器、继电器、PLC 、工控机、仪器仪表、气缸、五金工具、伺服电机、劳保用品等一系列自动化的工控产品。

实验5.10 光敏传感器的基本特性与应用研究凡是能将光信号转换为电信号的传感器称为光敏传感器，也称为光电式传感器，它可用于检测直接由光强度变化引起的非电量，如光强、光照度等；也可用来检测能转换成光量变化的其它非电量，如零件直径、表面粗糙度、位移、速度、加速度及物体形状、工作状态识别等。

光敏传感器具有非接触、响应快、性能可靠等特点，因而在工业自动控制及智能机器人中得到广泛应用。

光敏传感器的物理基础是光电效应，光电效应通常分为外光电效应和内光电效应两大类。

在光辐射作用下电子逸出材料的表面，产生光电子发射称为外光电效应，或光电子发射效应，基于这种效应的光电器件有光电管、光电倍增管等。

电子并不逸出材料表面的则是内光电效应（包括光电导效应、光生伏特效应）。

也即半导体材料的许多电学特性都因受到光的照射而发生变化。

几乎大多数光电控制应用的传感器都是基于内光电效应的器件，通常有光敏电阻、光敏二极管、光敏三极管、硅光电池等。

本实验主要是研究光敏电阻、硅光电池、光敏二极管、光敏三极管等光敏传感器的伏安特性和光照特性，及两个具体应用电路。

1.光敏传感器的基本特性光敏传感器的基本特性包括：伏安特性、光照特性、光谱特性、温度特性、频率特性、暗电阻、亮电阻、响应时间等。

掌握光敏传感器基本特性的测量方法，为合理应用光敏传感器打好基础。

伏安特性：光敏传感器在一定的入射光照度下，光敏元件的电流I与所加电压U之间的关系称为光敏器件的伏安特性。

改变照度则可以得到一簇伏安特性曲线。

它是传感器应用设计时的重要依据。

光照特性：光敏传感器的光谱灵敏度与入射光强之间的关系称为光照特性，有时光敏传感器的输出电压或电流与入射光强之间的关系也称为光照特性，光照特性是光敏传感器应用设计时选择参数的重要依据之一。

2.光敏传感器的应用运用掌握了其基本特性的光敏传感器设计两个应用电路，如测光强电路、光传输电路等，并用面包板装调该电路，检验所设计电路的功能。

GENERAL USE AND APPLICATIONSUse your smartphone, tablet or computer to remotely monitor ambient temperature and humidity levels that affect your home second home, office or rental property.* The 6 foot detachable dry probe measures temperature of air outside through a window, or even in your refrigerator or freezer.* Text & e-mail alerts can signify power outages to help you protect property or prevent frozen pipes.*MONITORING OPTIONS•Home, second home, office or rental property•Indoor or outdoor temperature and humidity •Basement, garage, attic and utility room •Refrigerators, freezers and dry food storage•Plants, gardens and greenhouses•Outdoor pets, farms and livestock•Books, photos and musical instruments•Computers, servers and electronics•Wine storage and humidors•Fireplace mantelPACKAGE CONTENTSHARDWARE:1. Wireless Ambient Temperature and HumidityMonitor with mounting bracket (TX60U-IT)2. *Wet or Dry Temp. Probe included in select packages.See (B) in the FEATURES AND MEASUREMENTSsection for more details.3. Mounting hardware (screws and drywall anchors) PRINTED MATERIALS:5. Printed Product Overview Guide (this document)IMPORTANT: Product set up and activationinstructions are online: 6. IMPORTANT: Activation Key Card required forset up and activation. Do not throw away.•Two fresh AAA, IEC LR03, 1.5V Alkaline batteries•Two-sided tape as needed•Browser with high speed Internet•Network router•Existing La Crosse Alerts Internet Gateway with mounting bracket, AC adapter and LAN cable (sold separately)FEATURES AND MEASUREMENTS (Diagram 1)(A) Wireless Ambient Temperature & Humidity Monitor:•LCD displays ambient air temp. & humidity (CH1)•LCD displays probe temperature (CH2)•Transmits collected data to Internet Gatewaywithin a 200 Ft. wireless range.•Weather resistant case (not water proof)Note: The case with LCD cannot get wet andmay be affected by high humidity conditions.•Wall hanging or free standing(B) **Optional Temp. Probe on 6 Ft. Detachable Cable:•Wet & Dry temperature probes are sold separately.Check your retailer for availability. Attach a probe atany time with no need to reset sensor.•**Attach a dry temperature probe to the main sensorcase to monitor DRY environments such as air or drysoil. MODEL #: D000.101.BG•**Or attach a Wet probe for measuring wet or humidconditions such as a pool, aquarium or terrarium:MODEL #: D000.102.BG or D000.103.BGHOW IT WORKS•The wireless sensor transmits temperature and humiditymeasurements to the Internet Gateway within a 200 Ft.(60.96m) wireless range.*•The Internet Gateway (sold separately) connects to yourexisting network router and uses your high-speed Internetconnection to upload collected measurements to your ownaccount at .*•Once the sensor and gateway are activated on youraccount, you can monitor sensor(s) online from a(1) *(2)(B)**Optional externalin select packages.smartphone, tablet or computer, and set up custom e-mail/text alerts*.•Add up to 5 sensors (sold separately) per Internet gateway (sold separately) to monitor additional areas.1. Begin set up near your existing network router and a computer with high-speed Internet access.2. Unpack package contents and insert temp. probe (if it’s included) into the TX60U-IT case (see diagram 1).1. Locate the Activation Key Card in the package for setupinstructions and the Activation Key . The Activation Key is necessary to activate your sensor with Internet Gateway (sold separately). Keep your Activation Card for reference. 2. Visit with your Activation KeyCard to create your account and activate the product.ACTIVATION INFORMATION:THE INCLUDED ACTIVATION KEY is good for1 year of ENHANCED SERVICE with early warning text & e-mail alerts, plus 4 more years of BASIC SERVICE for standard remote monitoring.Lost your Activation Key Card?Contact Customer Support:/support/alerts Phone: (608) 785-7920Once the sensor is activated and building a measurement log, you can download the data as a comma separated values (CSV) file. You must use an application such as Microsoft Excel® or Google Docs® that supports comma separated values (CSV) formatted files to view the table data.• Select a location protected from water and otherprecipitation. The case is water resistant, not water proof. • Place the sensor in a dry, shaded area. Avoid locations with direct sun, to prevent inaccurate readings.• Fog and mist will not harm the sensor but direct precipitation must be avoided.• Note: Exposing the sensor case to extreme humidity may temporarily disrupt data. The sensor case reads humidity, but should not be submerged in water.• Select a location within range of the Internet gateway (see “IMPORTANT SETUP & OPERATION NOTES”).• IMPORTANT: Before permanently mounting…Test sensor in the desired mounting location for at least 1 hour to confirm good reception. Confirm consistent readings on your account at before permanentlymounting. Move the sensor closer to the Internet Gateway if the signal is lost or not received. • Mount the sensor after the activation process (see “SETUP AND ACTIVATION”). MOUNT TO WALL WITH SCREWS1. Remove the mounting bracket2. Place bracket over the desired location.3. Mark mounting surface with a pencil through the 2 holes of the bracket.4. Screw bracket onto surface and tighten screws to bracket.5. Insert the sensor back into the bracket.FREE STANDINGAttach the mounting bracket to the bottom or top of the sensor and place it on any flat surface.PLACEMENT OF TEMPERATURE PROBE (Optional)• Confirm that the end of the probe cable is secured in the socket inside the sensor (See Diagram 1).• Insert the dry temp. probe on 6 Ft. cable into a refrigerator or freezer, or dry soil, etc. for a separate reading of air or soil temperature. The dry temp. probe is not for use in water. • **An optional wet probe should be used to measure wet environments (sold separately). Check your retailer for availability: MODEL #: D000.102.BG• Loosely coil and secure extra cord with a twist tie or secure with tape (not included).• The sensor has a wireless range of 200 feet (60.96 m). The 200 ft. range equates to open air with no obstructions, and that radio waves DO NOT curve around objects. Actualtransmission range will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings, etc.) will effectively cut signal range in half.• Metal, stucco, and some types of glass can reduce signal range by as much as ¾ or more, compared to the ½ reduction typical of most obstructions. It is possible toreceive a signal through these materials, however maximum range will be reduced due to their tendency to absorb or reflect a much larger portion of the sensor’s signal.• The sensor measures and updates the temperature and humidity on the LCD every 6 seconds.Note : The new measurement is reported to your account at intervals that you select using your online account.1. Remove the battery cover by sliding the cover down.2. Observing the correct polarity install 2-AAA batteries. The batteries will fit tightly (to avoid start-up problems make sure they do not spring free).3. Do not mix old and new batteries.4. Do not mix alkaline, lithium, standard or rechargeable batteries.5. Replace the battery cover by sliding upwards and check that it is securely fitted.• Low battery icon appears on LCD when batteries are low. • You will receive an e-mail or mobile text message alert when the battery power of the sensor is low. Change the batteries immediately.Note: The LED light turns ON briefly after changing batteries. The LED light turns OFF when not needed to save battery power. The previously stored information in the temperature and humidity sensor will not be affected or cancelled while you change the batteries.• Avoid extreme temperatures, vibration and shock. • Clean the sensor with a soft, damp cloth. Do not use solvents or scouring agents.• Do not submerge the sensor case in water. • Do not kink the 6 ft. sensor cable.• Secure the 6 ft. cable to avoid tripping hazards.• Immediately remove all low powered batteries to avoid leakage and damage.• Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology® for repairs.Temperature range:-40°F to 140°F with 0.2°F resolution“OFL” displayed if outside this range. Humidity measuring range: 3% to 99% Transmission range:200 feet (60.96 m) in open spaceTemp. Probe 6 Ft. Cable: Channel 2:-40°F to 140°F with 0.2°F OPTIONAL resolution “OFL” displayed if outside this range, and displayed “nC” if probe is not connected.Sensor battery power 2 x AAA Alkaline, IEC LR03, 1.5V Internet gateway power: AC adapter (included) Battery life cycle:Approximately 24 monthsTX60U-IT size: 5.23" H x 0.76" W x 1.44" DLa Crosse Technology, Ltd provides a 1-year limited warrantyon this product against manufacturing defects in materials and workmanship.This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and serviceprocedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. Theoriginal dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remainingoriginal warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product isexamined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground returnshipping charges to the owner of the product to a USA address only.Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specifiedexceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, ordeterioration of, any accessory or decorative surface; (4)damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage resulting from theperformance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances.LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUMELIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH.This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information, please contact:La Crosse Technology, Ltd2817 Losey Blvd. S. La Crosse, WI 54601/support/alertsLost your Activation Key Card?Contact Customer Support:/support/alerts Phone: (608) 785-7920* Disclaimers: La Crosse Technology, LTD. (“La Crosse”) provides various alert and monitoring services to aid users. (1) Service providers may charge users for alert services. Standard messaging and data rates apply and will be billed to the customer’s wireless account. Customers may be unable to receive text messaging or data service in some areas due to unavailability of service. (2) La Crosse shall not be liable for accuracy, usefulness or availability of data transmitted via the service. Users are solely responsible for damages to persons or property by service use.All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher.This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the next issue.We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged.5,978,738 6,076,044 6,597,990This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received,including interference that may cause undesired operation.。