下载文档原格式
主船体main hull 上层建筑superstructure上甲板/上层连续甲板upper deck 船底bottom舷侧broadside 艏艉fore and aft舱壁bulkhead 水密watertight艏部bow 艉部stern/quarter二层甲板second deck 平台甲板platform deck桅屋masthouse 罗经甲板compass deck驾驶甲板bridge deck 船长甲板master deck高级船员甲板office deck 艇甲板boat deck船员甲板crew deck 机舱engine room货舱cargo hold 货舱口cargo hatch压载舱ballast tank 深舱deep tank燃油舱fuel oil tank 滑油舱lubricating oil tank淡水舱fresh water tank 污油水舱slop tank隔离空舱/干隔舱caisson 球鼻艏标志bulbous bow mark/BB mark首侧推器标志bow thruster mark/BT mark 吃水标志draft mark甲板线deck line 干舷甲板freeboard deck载重线标志load line mark 热带淡水载重线tropical fresh water load line/TF夏季淡水载重线fresh water load line/F 热带载重线tropical load line/T夏季载重线summer load line/S 冬季载重线winter load line北大西洋冬季载重线winter North Atlantic load line/WNA国际船舶载重线证书international load line certificate吃水指示系统draft indicating system 船舶尺度ship dimension最大尺度/全部尺度/周界尺度overall dimension 最大长度/全长/总长length overall/LOA最大宽度/全宽extreme breadth 最大高度maximum height净空高度air draught 船型尺度/型尺度/主持度moulded dimension 垂线间长L/length between perpendiculars 型宽B/moulded breadth型深D/moulded depth 型吃水d/moulded draft登记尺度register dimension 登记长度register length登记宽度register breadth 登记深度register depth船舶主尺度比dimension ratio 船长型宽比L/B , length breadth ratio船长型深比L/D , length depth ratio 船长型吃水比L/d , length draft ratio型宽型吃水比B/d , breadth draft ratio 型深型吃水比D/d , depth draft ratio重量吨weight tonnage 排水量displacement满载排水量dead displacement 空船排水量light displacement装载排水量load displacement 总载重量deadweight/DW净载重量net deadweight/NDW 容积吨/登记吨capacity tonnage总吨位/总吨gross tonnage/GT 净吨位net tonnage/NT运河吨位canal tonnage/CT 抗沉性floatability全客船passenger vessel 客货船passenger-cargo vessel货客船cargo-passenger vessel 客滚船ro-ro passenger ship集装箱船container ship 箱格导轨系统cellguide system散装货船bulk carrier 散装货物bulk cargo舱口围板hatch coaming 横剖面cross-section边舱side tank 压载舱ballast tank矿砂船ore carrier 压载边舱side ballast tank内底板inner bottom plating 兼用船combination carrier矿砂/石油两用船，O/O船ore/oil carrier 矿砂/散货/石油三用船，OBO船ore/bulk/oil carrier 杂货船general cargo ship 滚装船roll on/roll off ship , Ro/Ro ship木材船timber carrier 冷藏船refrigerated ship多用途船multi-purpose ship 液货船liquid cargo ship易燃液体inflammable liquid 油船oil tanker污油水舱slop tank 液体化学品船liquid chemical tanker液化气船liquefied gas carrier 液化天然气船liquefied natural gas carrier/LNG carrier液化石油气船liquefied petroleum gas carrier/LPG carrier 乙烯运输船ethylene tanker工程船engineering ship 挖泥船dredger起重船floating crane 海洋调查船marine survey ship敷缆船cable ship 航标船navigation mark ship工作船working ship 拖船tug供应船supply boat 破冰船icebreaker海难救助船rescue ship 消防船fire boat科学考察船scientific research ship 船体结构ship construction钢板plate 型钢section steel扁钢flat bar 球扁钢bulb bar角钢angle bar , A/B 工字钢I-barT型钢T-bar 槽钢channel bar铸钢，铸件casting 锻钢，锻件forging焊接welding 周围焊around welding电弧焊/电焊electric arc welding 气焊gas welding焊缝weld 塞焊plug welding端接焊end welding 角接焊fillet welding对接焊butt welding 搭接焊lap welding坡口groove 覆板doubling plate铆接riveting 板材deals and battens骨架skeleton 总纵强度total longitudinal strength扭转强度torsional strength 横向强度transverse strength局部强度local strength 坐坞强度docking strength刚度rigidity 稳定性stability应力集中stress concentration 船台building berth横骨架式transverse framing system 横向构件transverse member舷顶列板sheer strake 舷侧板side plating舭列板bilge strake 船底板bottom plating中内龙骨center keelson 旁内龙骨side keelson梁肘板beam knee 平板龙骨(flat) plate keel甲板纵桁deck girder 肋骨frame强肋骨web frame 舷侧纵桁side girder肋板floor 横梁beam横舱壁板transverse bulkhead plating 舱容hold capacity外板shell plate 内底板inner bottom plating纵向构件longitudinal member 自重sole weight纵骨架式longitudinal framing system 船底纵骨bottom longitudinal中桁材center girder 旁桁材side girder舷顶列板sheer strake 舷侧纵骨 side longitudinal撑材strut 甲板纵骨deck longitudinal强横梁web beam 舱口围板hatch coaming纵舱壁longitudinal bulkhead 舭龙骨bilge keel二层甲板tween deck 内底边板margin plate实肋板/主肋板solid floor 内底纵骨inner bottom longitudinal加强筋stiffener 人孔manhole舱口端梁hatch end beam 支柱pillar船舱肋骨hold frame 甲板间肋骨tweendeck frame舷侧列板side strake 舭肘板/污水沟三角板bilge bracket舱口端横梁hatch end beam 防倾肘板tripping bracket舷墙板bulwark plating 舷强扶强材bulwark stiffener换新renew 基本结构图basic construction plan纵中剖面结构图central fore-and-aft plane construction plan 各层甲板图deck plan 内底结构图inner bottom construction plan 列板strake舭列板bilge strake 甲板边板deck stringer基线base line 横剖面图transverse cross-section plan中横剖面图midship transverse cross-section plan机舱处横剖面图engine-room transverse cross-section plan货舱口处横剖面图cargo hatch transverse cross-section plan舱壁图bulkhead plan 总布置图general arrangement plan船底结构bottom construction 下甲板横梁lower deck beam上甲板横梁upper deck beam 支柱肘板pillar bracket双层底结构double bottom construction 骨架framing首防撞舱壁fore collision bulkhead 尾尖舱舱壁afterpeak bulkhead肘板bracket 水密肋板watertight floor内底纵骨inner bottom longitudinal 实肋板solid floor组合肋板/框架肋板bracket floor 扶强材side girder船底横骨bottom frame 流水孔drain hole透气孔air hole 减轻孔lightening hole切口incision 内底横骨inner bottom frame横骨架式双层底结构transversely framed double bottom construction轻型肋板lightened floor 水密舱壁watertight bulkhead面板 face plate 折边flanging中桁材/中底桁center girder 中内底板center inner bottom plating箱形中桁材/箱形龙骨duct keel 管隧pipe tunnel水密纵桁watertight longitudinal girder 内底纵骨inner bottom longitudinal内底横骨inner bottom frame 船底中心线bottom center line旁桁材/旁底桁/旁龙骨side girder 人孔盖manhole cover污水沟bilge drainage/side bilge 污水井bilge well/bilge sump单层底结构single bottom construction 中内龙骨center keelson旁内龙骨side keelson 舷侧外板side plating甲板边板deck stringer 主肋骨main frame甲板间肋骨tweendeck frame 尖舱肋骨peak frame肋距frame space 中间肋骨intermediate frame普通肋骨ordinary frame 强肋骨web frame舷侧纵桁side stringer 舷侧纵骨side longitudinal舷边gunwale 舷边角钢gunwale angle bar止裂crack arrest 舷墙bulwark舷墙板bulwark plating 支撑肘板buttress bracket扶手armrest 栏杆hand rail舱口纵桁hatch side girder 甲板纵中线deck center line舱口端梁hatch end beam 强力甲板strength deck甲板间舱tweendeck space 遮蔽甲板shelter deck舱壁甲板bulkhead deck 干舷甲板freeboard deck量吨甲板tonnage deck 半梁half beam斜置加强筋tilt stowing stiffener 管型支柱tubular pillar水平加强筋horizontal stiffener 菱形面板diamond plate悬臂梁cantilever beam 梁拱camber舷弧线sheer curve 舷弧sheer首舷弧fore sheer 尾舷弧after sheer首尖舱fore peak tank 首尖舱舱壁fore peak tank bulkhead防撞舱壁collision bulkhead 尾尖舱舱壁after peak tank bulkhead 防火舱壁fireproof bulkhead 液体舱壁liquid bulkhead油密oiltight 制荡舱壁wash bulkhead平面舱壁plane bulkhead 舱壁板bulkhead plate舱壁扶强材bulkhead stiffener 水平桁horizontal girder对称槽形舱壁symmetrical corrugated bulkhead 三角形triangle矩形rectangle 梯形trapezoid弧形arc 双层底double bottom tank底边舱lower side tank 顶边舱top side tank底登lower stool 直立型首straight bow首柱stem/stem post 驳船barge前倾型首raked bow 飞剪型首clipper bow首楼甲板forecastle deck 破冰型首ice resistant bow兴波阻力wave making resistance 形状阻力form resistance铸钢首柱cast steel stem post 钢板首柱steel plate stem post锚链舱chain locker 升高肋板raised floor强胸横梁panting beam 外板shell plate开孔平台trepanned platform 椭圆形尾elliptical stern巡洋舰形尾cruiser stern 方型尾transom stern尾封板stern transom plate 船首结构bow construction强力构件strength member 剖面模数section modulus船尾结构stern construction 尾肋板transom floor尾柱底骨sole piece 推进器柱propeller post轴毂propeller boss 舵钮rudder gudgeon舵柱rudder post 斜横梁cant beam舵机舱平台steering gear room platform 尾升高肋板stern raised floor斜肋骨cant frame 舵杆管rudder case防火措施fire precaution 防火结构fire structure耐火材料refractory material 主竖区main vertical zone不燃材料non-combustible material 自燃autoignition易燃蒸气inflammable vapour 可燃材料combustible material等效材料equivalent material 防火分隔fire resisting divisionA级分隔/甲级分隔A class division 天花板ceiling衬板furring 轴隧shaft tunnel推进器轴propeller shaft 逃生孔escape trunk中机型船amidship-engined ship 尾机型船stern-engined ship单车船single-screw ship 顶板top plating木铺板batten ceiling 滑动式水密门slid watertight door拱形顶板arch top plating 平顶板flat top plating轴承基座stool supporting shaft bearing 管系piping格子板grating 舭龙骨/减摇龙骨bilge keel坞修dock repair 船底塞docking plug坞墩docking block 锰黄铜manganese brass不锈钢stainless steel 舭部外板bilge plate舷侧型线moulded line of side shell 船底型线moulded line of bottom shell 垫圈insertion ring 垫板pad隔离空舱caisson 双层舷侧double side shell双层壳double shell 中间舱center tank边舱side tank 甲板下纵桁deck lower girder业务衡准数criterion of service numeral 舱底水管系bilge system舱底水管路bilge pipe 吸口suction过滤器filtrator 舱底水总管bilge main line止回阀non-return valve 舱底泵bilge pump阀箱valve casing 泥箱mud box油水分离器oil-water separator 测量管/测深管sounding pipe旋塞faucet 螺纹盖thread cap防击板striking plate 压载管系ballast system压载水ballast water 压载管路ballast pipe调驳阀箱control valve easing 压载泵ballast pump截止阀stop valve 海底阀/通海阀sea suction valve舷侧排水阀overboard discharge valve 空气管air pipe花钢板diamond plate 自动关闭阀automatic closing valve通风管系ventilating system 自然通风natural ventilation烟斗式通风筒cowl-head ventilator 排风筒uptake ventilator蘑菇形通风筒mushroom ventilator 起重柱Samson post鹅颈式通风筒gooseneck ventilator 机械通风mechanical ventilator风机aerator 管路pipe conduit吸口空气滤器suction air filter 空气调节air conditioning system消防管系fire extinguishing system 固定式灭火系统fixed fire extinguishing system 水灭火系统water fire extinguishing system 气体灭火系统gas fire extinguishing system 泡沫灭火系统foam fire extinguishing system水雾灭火系统water fog fire extinguishing system自动喷水系统automatic sprinkling fire extinguishing system惰性气体保护系统inert gas system 日用水管系domestic water supply system日用淡水系统domestic fresh water system 日用热水系统domestic warm water system 饮用水系统potable water system 重力水柜gravity tank压力水柜pressure tank 循环泵circulating pump甲板排水管系 deck scupper system 甲板排水器deck scupper排水管scupper pipe 卫生排泄系统sanitary water system锚anchor 锚穴anchor recess锚链筒hawse pipe 制链器chain stopper锚机windlass 锚链管chain pipe锚链舱chain locker 锚链chain cable闸刀switch blade 制动销detent pin松紧螺丝扣turnbuckle 弃链器releasing gear横闩式弃链器dog type cable clench 螺旋弃链器screw type cable releaser手轮hand wheel 螺杆screw脱钩senhouse slip 末端链环end open link首锚bow anchor 尾锚stern anchor有杆锚/海军锚stocked anchor 锚铃环anchor ring锚干anchor shank 锚爪anchor fluke锚冠anchor crown 锚爪臂anchor arm锚尖anchor bill 锚爪掌anchor flukepalm锚杆销forelock pin 横杆folding stock无杆锚/山字锚stockless anchor 锚卸扣anchor shackle锚肩/助抓突角anchor shoulder 销轴pintle横销pin cotter 大抓力锚high holding power anchor普通链环common link 加大链环enlarged link末端链环end open link 散合式连接链环detachable link肯特卸扣Kenter link 转环swivel link电动锚机electric windlass 电动液压锚机hydraulic windlass电动机electromotor 减速器reducer传动齿轮drive gear 离合器clutch链轮chain wheel 刹车操纵杆brake control rod带缆卷筒rope drum 带式刹车brake绞盘capstan 锚机间windlass room锚链末端bitter end 舾装数/船具数N/equipment number备锚spare anchor 大抓力锚HHP超大抓力锚SHHP 挂锚hanging off an anchor。
“Maritime Terminology: Essential Vocabulary for Ships”1.Bow: The front part of the ship.2.Stern: The back part of the ship.3.Port: The left side of the ship when facing forward.4.Starboard: The right side of the ship when facing forward.5.Hull: The main body of the ship, excluding superstructure and machinery.6.Deck: The horizontal surface of a ship where people walk or work.7.Bridge: The navigational control center of the ship, usually located at the front.8.Bulkhead: A partition wall within the hull of the ship.9.Keel: The central structural member of the ship’s hull, running along the bottom.10.Rudder: A movable device used to steer the ship.11.Propeller: A rotating device that propels the ship through the water.12.Mast: A vertical structure on the ship that supports sails or antennas.13.Bilge: The lowest compartment on a ship’s hull, often prone to collecting water and otherliquids.14.Ballast: Weight added to a ship to improve stability or adjust draft.15.Cargo Hold: A space within the ship’s hull for storing cargo.16.Anchor: A heavy object deployed to keep the ship stationary.17.Windlass: A machine used for raising and lowering the anchor.18.Lifeboat: A small boat carried by a ship for use in emergencies.19.Buoy: A floating object used for navigation or marking hazards.20.Chart: A map used for navigation, showing water depths, landmarks, and other relevantinformation.These are just a few examples of the many specialized terms used in the maritime industry. Understanding these terms is essential for effective communication and safe operation aboard ships.。
船舶专用词汇1.船舶的分类passenger ship 客船general cargo ship 杂货船bulk cargo carrier 散货船container ship 集装箱船roll on/roll off ship 滚装船tanker 油船liquid gas carrier 液化气船barge 驳船barge carrier 载驳船dredger 挖泥船floating crane 起重船floating dock 浮船坞ice breaker 破冰船drilling platform 钻井平台drilling ship 钻井船trawler 拖网渔船stern ramp trawler 尾滑道拖网渔船tug boat 拖船fire boat 消防船ocean survey ship 海洋调查船cruiser 巡洋舰destroyer 驱逐舰frigate 护卫舰aircraft carrier 航空母舰submarine 潜艇hydrofoil craft 水翼艇air cushion vehicle 气垫船—hovercraft 全浮式气垫船—sidewall air cushion vehicle 侧壁式气垫船small waterplane area twin hull ship 小水线面双体船semi-submerged catamaran 又称为半潜双体船2.船体结构longitudinal bending 总纵弯曲hogging 中拱弯曲sagging 中垂弯曲longitudinal strength 总纵强度transverse strength 横向强度local strength 局部强度hull 船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 艏楼bridge 桥楼poop 艉楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁fore peak bulkhead 艏尖舱舱壁after peak bulkhead 艉尖舱舱壁3.外板和甲板板shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 船底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板upper deck 上甲板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板4.船底结构center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 钢板折边法兰bilge bracket 舭肘板floor 肋板solid floor 主肋板watertight floor 水密肋板bracket floor 框架肋板lightened floor 轻型肋板stiffener 加强筋扶强材bulb plate 球扁钢angle bar 不等边角钢bottom center girder 中底桁bottom center girder 旁底桁duct keel 箱形中底桁pipe tunnel 管隧reverse frame 内底横骨bottom frame 船底肋骨longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨inner bottom plate 内底板margin plate 内底边板man hole 人孔bilge well 污水井bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 艉室emergency exit 应急通道bilge keel 舭龙骨5.舷侧结构Integrated barge 分节驳frame 肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材6.甲板结构beam 横梁deck beam 普通横梁hatch end beam 舱口端横梁deck girder 甲板纵桁side stringer 舷侧纵桁hatch side girder 舱口纵桁beam knee 梁肘板sponson deck 舷伸甲板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 货舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁pillar 支柱topside tank 顶边舱excess hatch 出入舱口expansion trunk 膨胀井7.舱壁结构bulkhead 舱壁cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical stiffener 垂直扶强材8.首尾端结构vertical bow 直立型艏raked bow 前倾型艏clipper bow 飞剪型艏ice breaker bow 破冰型艏elliptical stern 椭圆形艉cruiser stern 巡洋舰型艉transom stern 方形艉fore peak艏尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱breast hook 艏肘板stem 艏柱steel plate stem 钢板艏柱forged steel stem 锻钢艏柱combination cast and rolled stem 混合式艏柱tunnel 管隧thruster 侧推器after peak 艉尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame 艉柱shoe piece 艉柱底骨rudder post 舵柱propeller post 螺旋桨柱propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架9.上层建筑和机舱棚结构accommodation 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass platform 罗经平台expansion joint 伸缩接头derrick post桅杆derrick platform 起货机平台tower post 塔式桅stern door 艉门bow door 艏门visor type 罩壳式side hinged type 边铰链式pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱ballast water tank 压载水舱conning tower sail 指挥台围壳渔业船舶种类2.1 渔船fishing vessel 用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
船舶英语必备实用词汇船舶英语词汇dugout独木舟barge驳船kayak(爱斯基摩人的)木排outrigger桨叉架船rowing boat划艇(美作：rowboat)gondola(意大利的)长平底船whale mother ship捕鲸母船hydrofoil水翼船catamarans双体船dredger挖泥船boat船brig， brigantine双桅船canoe小船，独木舟caravel快帆船cargo boat货船coaster近海贸易货船cod-fishing boat捕鳕鱼船whaler捕鲸船collier运煤船battleship战船shallop小型战船coastguard cutter，coastguard vessel巡逻艇，缉私艇revenue cutter缉私船patrol boat巡逻艇minesweeper扫雷艇torpedo boat鱼雷艇frigate轻护航舰gunboat炮舰submarine潜水艇destroyer驱逐舰corvette轻巡洋舰cruiser巡洋舰aircraft carrier航空母舰ferry， ferryboat渡船，渡轮fishing boat渔船freighter货船galleon大型帆船galley大划桨船hovercraft气垫船icebreaker破冰船launch艇lifeboat救生艇lighter驳船liner， ocean liner远洋班轮merchant ship， merchantman商船motorboat摩托艇outboard尾部装有马达的小艇paddle steamer， paddle boat明轮船 passenger boat客船piragua， pirogue独木舟raft木筏sailing boat， sailing ship帆船schooner纵帆船ship船skiff小艇sloop单桅船steamer， steamship汽轮tanker油轮trawler拖网渔船tug， tugboat拖轮vessel船yacht游艇yawl船载小艇船舶工程专业英语口语词汇1、柴油日用柜 Diesel oil daily tank2、柴油澄清舱 Diesel oil setting tank3、燃油日用柜 Fuel oil daily tank4、燃油澄清舱 Fuel oil setting tank5、滑油澄清舱 Lubricating oil setting tank6、滑油储藏舱 Lubricating oil store tank7、滑油循环舱 Lubricating oil circulating tank8、燃油溢油舱 Fuel oil overflow tank9、燃油油渣舱 Fuel oil sludge tank10燃油深舱 Fuel oil deep tank11滑油污油舱 Lubricating dirty oil tank12滑油溢油舱 Lubricating oil overflow tank13滑油油渣打舱 Lubricating oil sludge tank14主机淡水膨胀水箱 M.E fresh water expansion tank15付机淡水膨胀水箱 A.E fresh water expansion tank16、淡水压力柜 Fresh water pressure tank17、热水压力柜 Hot water pressure tank18、饮水压力柜 Drinking water pressure tank19、淡水舱 Fresh water tank20、饮水舱 Drinking water tank21、锅炉水舱 Boiler water tank22、分油机工作水箱 Purify operating water tank23、汽缸油日用柜 Cylinder oil daily tank24、尾管滑油重力柜 Gravity tank of tube oil25、排气水封箱 Exhaust seal water tank26、蒸馏水水舱 Distilling water tank27、污水井 Bilge well1、滑油系统 Lubricating oil piping system2、燃油系统 Fuel oil piping system3、海水系统 Sea water piping system4、缸套水系统 Cylinder cooling water piping system5、启动空气系统 Start air piping system6、控制空气系统 Control air piping system7、排气系统 Exhaust piping system8、日用供水系统 Daily water piping system9、蒸汽系统 Steam piping system10 、锅炉给水和凝水系统 Feed water and condensate of boiler piping system11、燃油净油系统 Fuel oil purified piping system12、燃油输送系统 Fuel oil transport piping system船舶英语词汇。
..船舶航海英语词汇 Ranks of ship ’s crew(船员职务) crew 船员 captain （master ） 船长 chief officer 大副 or chief mate （first mate ） second chief 二副 or second mate third officer 三副 or third mate assistant officer 驾助 radio officer （radio 报务员operator, wireless operator ） purser (chief purser) 管事,事物长 clerk 事务员 boatswain or bosun 水手长 cassab 副水手长 quartermaster 舵工 coxswain 舵工,艇长 able seaman 全能水手,一水 a.b.(able bodied seaman)全能水手 e. D.h. , d.h.u. 全能水手 o.s.(ordinary seaman)普通水手,二水 seaman, mariner 普通水手,海员 deck boy 甲板员 engineer 轮机员 chief engineer 轮机长,大车,老轨 second engineer 大管轮,二车,二轨 third engineer 二管轮,三车,三轨 fourth engineer 三管轮,四车,四轨 assistant engineer 轮助 mechanic 机工 fireman 生火 cleaner or wiper 清洁工 chief steward 大管事 (or catering officer) second steward 二管事 chief cook 大厨 second cook 二厨 supernumerary 额外人员 ship ’scomplement 船上的定员 deck serang 水手长 deck tindal 副水手长 seacunny 舵工 Names of marine organizations and their( 船务机关名称及工作人员) harbour administration bureau (or harbour bureau)港务局 the joint inspection party-inward and outward 进口联合检查组 harbour supervision office 港务监督 the customs 海关 frontier inspection station 边防检查站 quarantine office (s0ervice) 卫生检疫所 animal and plant quarantine service 动植物检疫所 china commodity inspection and testing bureau(ccitb) 中国商品检验局 china marine bunker supply corporation 中国船舶燃料供应公司 china national chartering corporation(zhongzu) 租船公司 china ocean shipping agency 中国外轮代理公司 china ocean shipping company (cosco) 中国远洋运输公司 china ocean shipping company chartering department(coschard) 中国远洋轮船公司租船部 (“中远租”) chian ocean shipping tally company 中国外轮理货公司 china ocean shipping supply corporation(supco.)中国外轮供应公司 the ~ office of the register of shipping of the people ’s republic of china 中华人民共和国船舶检验局~办事处 joint inspection party 联检小组 customs officer 海关官员 harbour officer 港务监督员 frontier defence officer (inspector ,guard) 边防检查组 Quarantine officer(dotor) 卫生检疫员 customs boarding office 登轮官员 customs searching party 海关检查组 docker 码头工人(广义) longshoreman 码头工人(在岸上装卸) stevedore 码头工人(在船上装卸) foreman 装卸队长 pilot 引水员 cargo surveyor 商品检验员 marine or ship surveyor 验船师 chief tallyman 理货员 waterman 加水工人 agent 代理 Marine loading and discharging gear and harbour facilities （海运装卸机械工具和港口设施） barge 驳船 beacon 航标灯 belt conveyor 皮带运输机 board palnk 木版 bridge crane 桥吊，装卸桥 bunkering tanker 供燃料船 buoy 浮筒，浮标 can hook ，barrel sling 吊桶钩 canvas 帆布 canvas sling 吊货帆布袋 cargo tray 吊货盘 cargo runner 吊货钢丝绳 chafing plate 防擦板 chafing mat 防擦席 chain sling 链条吊索 crane 吊车 cold storage 冷藏仓库 conveyor belt 传送带 crowbar 撬杠 customs launch 海关关艇 dolphin 系缆桩 dunnage 垫仓物料 electric crane 电吊 elevator 升降机 ferry boat 轮渡船 fire boat 消防船 floating crane 浮吊 footboard 踏板 fork - lift 铲车，叉车 funnel 漏斗 gangboard 跳板 gantry crane 龙门吊 garbage(sludge,sewage) boat 垃圾船 grab 抓斗 grain elevator 吸粮机 hammer 铁锤 handcart 手推车 harbour light 港口灯标 iron nail 铁钉 landing pier 登岸码头 lifting maget 西铁吊具 lighter 驳船 light house 灯塔 light ship 灯船 manila rope 白棕绳 mat 席子 mobile crane 流动吊车 mooring anchorage 系泊锚地 mooring buoy 系泊浮筒 motor launch 小汽艇 nylon rope 尼龙绳 oil hose 输油软管 open yard 露天货场 personnelboat 交通艇 pilot boat 引水船 plate hook 钢板吊钩 pontoon 浮码头 pontoon bridge 浮桥 quarantine anchorage 检疫锚地 quarantine vessel 检疫船 refrigerator car 冷藏车 rope sling 绳吊索 saw 锯 semi-portal crane 半门吊 shifting board 防动板 signal tower 信号台 steam launch 小汽艇 steel wire 钢丝绳 tower crane 塔吊 tractor 牵引车 traffic boat 交通艇 tug boat(motor tug) 拖轮 warehouse 仓库 water boat 供水船 watr lever indicator 水深标尺 wire cargo net 钢丝网络 wire sling 钢丝吊索 various kind of vessels （各种船舶） air cushion craft 气垫船 bage-carrier 载驳货船 bulb-bowed ship 球鼻首船 bulk-carrier 散货船 cargo liner 定期货船 collier 散货船 crew boat （船员）联络船 diesel boat 柴油机船 dry cargo ship 干货船 dumb lighter 驳船（没有机器的） freighter 货船 oil barge 油驳 ore carrier （ore ship ） 矿砂船..reefer （refrigerator ship ） 冷冻船 salvage vessel 救助船 grain carrier 运量船 ice-breaker 破冰船 light ship 未载货的货船 lumber carrier （timber carrier ） 运木船 meat ship 肉类船 moto ship 内燃机船 ocean-going vessel 远洋船 sister ship 姐妹船 steam ship 蒸汽机船 stor carrier 补给船 tanker （oil tanker ） 油驳 trawler 拖网渔船 Major marine papers and certificates （主要船务单据及证书） （1）papers 单据 application for bunkers 加(燃油)申请书 application for tallyman 理货申请书 bill of lading 提单 booking note 订舱单 boat note 订载单 cargo receipt 交货收据 cargo tally sheet 理货记数单 copy 副本 damaged cargo report 货物残损报告书 declaration 申报单 delivery order 交货单 dock receipt 码头收据 gang record 工班报单 hatch(cargo)list 分舱单 inward manifest 进口舱单 license 许可证 mate ’s receipt 收货单 notice of arrival 到货通知书 motice of claim 索赔通知 notice of readiness 准备就绪通知书 on-spot record 现场记录 original 正本 outward manifest 出口舱单 parcel receipt 小包收据 sailing orders 开航通知 shipper ’s export declaration 货物出口申请书 shipping list 装货通知书 shipping permit 准运单 short/overlanded cargo list 货物溢短单 short/overlanded cargo report 货物溢短报告单 tally daily report 理货日报告 tally sheet 理货单 tally shift report 理货工班报告 2 )certificates ( 证书,证件) certificate of freeboard 干舷证书 certificate of health 无疫证书 certificate of origin 产地证书 ceitificate of port registry 船籍港证书 certicficate of survey 船舶检验证 classification certificate 船级证书 deratting certificate 除鼠证书 deratting exemption certificate 免予除鼠证书 inspection certificate 验讫单 international loading certificate 国际载重线证书 maritime declaration of health 航海健康申明书 navigation certificate seaworthiness certificate 适行证书 outward clearance certificate 出国证书 panama canal tonnage certificate 巴拿马运河吨位证书 passport 护照 safety radio telegraphy certificate 无线电报安全证书 ship ’s safety certificate 船舶安全证书 sues canal special tonnage certificate 苏伊士运河专用吨位证书 tonnage certificate 吨位证书 tonnage dues certificate 吨税证书 wireless inspection certificate 无线电安全证书 The structure of a ship(船舶结构) accomodation 房间 accomodation ladder 舷梯 aerial(antenna) 天线 aft part(after part) 船尾部 after-peak 后尖舱 air siren 汽笛 aldis lamp 闪光信号灯 alleyway 走道 anchor 锚 anchor chain 锚链 auxiliary machinery 辅机 bilge 船底沟 binnacle 罗盘支架 bitts(bollards) 系缆柱 block 滑轮 boom 吊杆 bow 船头 port bow 左舷船头 starboard bow 右舷船头 break 夹板台阶 bridge 船桥,驾驶台 brow (从船上到岸上的)舷梯 bulwarks 舷墙 bunker 燃料舱 cabin 船舱 pilot ’s cabin 引水员房间 cable 锚链 capstan 绞盘 cargo hold 货舱 catwalk 狭窄的舷梯 awning 帆布蓬 baggage room 行李房 barometer 气压表 basic line 吨位标志线 balk(blulk) , beam 船梁 hatch beam 舱盖横梁 port beam 左舷 starboard beam 右舷 chain locker 锚链舱 chronometer 经纬仪 coamings 舱口栏板 compass 罗盘course recorder 航向记录仪crane 起重机 davit 挂艇架 deck 甲板boat deck 救生艇甲板 lower deck 下甲板 lower tween deck 二层柜 main deck 正甲板 poop deck 船尾上面的甲板promenade deck 保护甲板之上甲板 shelter deck 遮蔽甲板 tonnage deck 量吨甲板 tween(between)deck 二层柜 upper deck 上甲板 upper tween deck 三层柜 deck house 甲板室 derrick 吊杆diesel engine 柴油机double bottom 双层底 draught marks(draft marks) 吃水标志 dynamo(generat 发电机 echo sounder 测深仪 engine roon 机舱 engin roon department 机舱部 escape trunk 救生道 fan room 打风间falg-staff 旗杆 forecastle 船首楼forecastle head 船头甲板 foremast 头柜 forepart 船头部 forepeak 前尖舱freeboard deckling 干舷甲板线 gangway 舷梯 glass (口语)气压表guy 稳索 gyro compass(gyro) 电罗经 halliard ,halyard 旗帜之升降索 hatch 舱口 hatch bord 舱盖板hatch coaming 舱口栏板 hatch cover 舱口盖 hawse hole 锚链孔 helm 舵轮;舵柄 hawser 船缆;锚链hull 舱壳jack ladder(jacob ’s ladder)软梯,绳梯 jackstaff 船头小旗杆 jigger mast 尾 jumbo(derrick 重吊(杆) keel 龙骨 life belt 救生带 life bort 救生艇 life buoy 救生圈 life jacket 救生衣 life raft 救生筏life-saving apparatus 救生设备 load ling 载重线,装载水线 mainmast man-rope 绳索mizzen mast monkey island 瞭望台 pilot ladder 领港梯子..piston 活塞 plimsol ’s mark 载重线标志 poop 船尾楼 port 港口,舱口,左舷 port -hole 舷舱,舱口 propeller 螺旋桨 pulley 滑轮 pump 水泵 purchase 绳索,滑轮 quarter 船舷的后部 port quarter 左舷后部 starboard quar 右舷后部 radar 雷达 radio 无线电 radio direction finder 无线电测向器 radio room 无线电室 radio transmitter 无线电发射机 rast 救生筏 rail,railings 扶手,栏杆 rat-guard 缆绳上的防鼠隔 ratlines 绳梯横索 refrigerated hol 冷藏舱 rig 帆索 rudder 舵 screw 螺丝钉 scupper 排水管 scupper board 挡水板 scanner 雷达扫描设备 sextant 六分仪 shaft tunnel 地轴弄 shackle 钩环 shifting board 防动板,防舱板 signal rocke 信号火箭 siren 汽笛 sling 吊索 starboard 右舷 steam engine 蒸汽引擎 steering gear 舵机 stem 船头 stern 船尾 storeroom 贮藏室 tackle 滑车,吊具 tank 液体舱 ballast tank 压载水舱 cofferdam tank 隔离沧 deep tank 深舱，深水柜 1 船舶专业英语词汇（初级） 1．基本，简单的词汇： AM 上午 PM 下午 Notification of inspection 检查验收通知单 Application 申请，申请单 Inspection 检验，报验 Technical discussion 技术讨论 On board 在船上 In the workshop 在车间 On the slipway 在船台上 At pier(wharf) 在码头 Fair 尚好的 The performance is merely fair 性能尚好 Terrible 极坏的，很糟的 So so 马马虎虎 So far ,so good 到目前，一切顺利 Worse 更糟的 worst 最差、最糟 Improvement 改进 Leave no room for improvement 完美，无缺点 Accept 接收 Accept subject to 有条件的接收，有待于……做好之后才接收 Reject 拒收 Comments 意见 defect lish 消除意见清单 Item 项目 memorandum 备忘录 manual n 、手册、说明书；a.手控的，手工的 drawings 图纸 working drawings 施工图 finished drawings 完工图 approved drawings 认可图 drawings for approval 送审认可图 supporting technical doucuments 基础技术文件 sketch 草图 draw a sketch 画草图 up to the standard 达到标准 substandard 低于标准的 crane 吊车 building berth 船台 slipway 船台、下水滑道 dry dock 干无坞 pier 突码头、突堤 wharf 码头 along side (船)靠码头 foreman 工长，领班 coordinator 调度员 inspector 检查员 supervisor 管理人、监督人，监造人 surveyor 验船师 2、船体总体，及各类型船舶 Hull 船体 Forecastle 艏楼 Stern 船尾 Poop 艉楼 Superstructure 上层建筑 Foremast 前桅杆 After mast 后桅杆 Radar mast 雷达桅杆 Main deck 主甲板 Upper deck 上甲板 Poop deck 艉楼甲板 Accommodation deck 生活甲板 Compass deck 罗经甲板 Funnel 烟囱 Bridge 桥楼，驾驶台 Bridge wing 驾驶室翼桥 Wheel house 驾驶室 Engine room 机舱 Engine control room 机舱集控室 Catwalk 天桥、步桥 Flying bridge （露天）航行驾驶室 Rescue boat 救助艇 Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船 Naval Ship/war shipd 军船 Ice-breaker 破冰船Container vessel 集装箱船 Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架 Chemical carrier 化学品运输船 Liquefied gas carrier 液化气体船 Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇 Canoe 独木船，皮舟Junk 平底中国帆船、舳板 Gondola （意大利威尼斯的 ）一种狭长的平底船Yacht 快艇、游艇 Fast boat 快艇 Patrol boat 巡逻艇Anti-smuggling boat 缉私艇 Torpedo boat 公安艇 Ferry 渡船Catamaran 双体船 Jet foil 喷水水翼艇Wing assrsted vessel 地效船 3、各专业基本词汇 1）船体：Draft forward 前吃水 Draft middle 中吃水 Draft after 后吃水 Plimsoll mark/line Waterline 吃水线Waterlines （型）水线 Port 左舷 Starboard 右舷Sagging 中垂、下垂、下挂（流） Hogging 中拱、上拱 Derformation 变形Fairing 光顺、火工校正 Hot work 热工、明火作业 section 分段、部分、剖面 Block 分段Keel （船舶）龙骨 Bilge keel 舭龙骨Power tool 带动力工具（风动或电动） Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊 D.C welding 直流（电弧）焊 Grinding 打磨 Welding 电焊Spatters 飞溅（电焊） Under out 咬口 Sharp edge 快口2 船舶专业英语词汇（初级） Deflection 挠曲，变形 Slags 渣..Welding slags 电焊渣Automatic welding 自动焊 Manual welding 手工焊 Arc welding 电弧焊Gas shielded welding 气体保护焊 Inter gas arc welding 惰性气体保护电弧焊Welding seam 焊缝Bending machine 弯曲机Three-roll bending machine 三芯弯板机 Torsional box 抗扭箱 V oid space 空舱 Cofferdam 隔离舱 Bulwark 舷墙，防浪板 Wall 墙壁 Floor 地板Controllable pitch 可调桨 Elastic coupling 弹性联轴节 Bellow 波纹管 Joint 接头 Gaskets 垫片Fitting bolts 拂螺拴 Chock 制动块、导缆器 Chock fast 环氧垫块 Foundation 底座、基座 Mounting 装置、座、架Mount （常指火炮等武器的）座，架 Vent pipe 透气管 Sounding pipe 探测管Vapour return line 油气回路管 Stripping line 扫舱管Safety equipment 安全设备 Life-saving equipment 救生设备 Cargo hold 货舱 Cargo oil tank 货油舱 Cabin 船舱、舱室 Room 房间Store room 储藏室 Cold room 冷库 Fish room 鱼库 Meat room 肉库 Provision room 粮库 Foam room 泡沫库 CO2 room 二氧化碳室 Pump room 泵室Battery room 蓄电池室 Radio room 报务室 Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统 Sea water piping system 海水管系 Water jacket 水套Insulation materials 绝缘材料Lagging 绝缘材料、外套（锅炉、管子等） 3）电器 Current 电流 V oltage 电压 Frequency 频率 Contact 触点、触头 Ballast 镇流器Convertor 变频器、换能器 Conductor 导体Semi-conductor 半导体 Rectifier 整流器 Transformer 变压器 Thermostat 恒温器 Thermister 热敏器Edison base 螺丝灯座、爱迪生灯座 Bayonet base 卡口灯座 On-off 开关（量）Analogue 模拟，模拟设备Active analogue 有源模拟、主动模拟 Passive analogue 无源模拟、被动模拟 Dry contact 无源模拟、干接触 Buzzer 蜂鸣器 Button 按扭，电扭 Switch 开关Main switch 主开关Main switch board 主配电板 Cable 电缆 Wire 电线Three-core cable 三蕊电缆 Clamp 夹钳、夹具 Clip 接线柱、线夹Alligator clip 鳄鱼夹、弹簧夹 V oltage drop 电压降 Speed droop 速度降低 Black out 黑灯试验 Power failure 失电 Setting point 设定点 Adjust 调正（v ） Adjustment 调正（n ） Oscillator 振荡器、振动器 Oscilloprobe 示波器测试头 Oscilloscope 示波器、示波仪 Resistor 电阻、电阻器Potentiometer 电位器、电势计 Electrolysis 电解（作用） Electrolyte 电解质、电解液setting point of power surplus 负载余量设定值 重载询问test the power surplus setting point 重载询问试验 4）漆、木Surface preparation 表面处理（清理工作）Blasting equipment 喷漆（砂粒）装置 Sand blasting 喷砂除锈 Pre-blasting 预喷砂 Lingt blasting 预喷砂 Full blasting 通喷砂 Sand sweep 扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting 通喷砂后钢结构检查Cleanliness inspection 清洁度检查 Inspection after degreasing 除去油脂后检查Removing oil stains by detergent/solvent 使用洗洁剂/容剂除去油迹 Shop primer 车间底漆Spray painting 喷漆、喷涂法 Touch-up 补漆、修正Touch-up painting 补漆、点漆 First coat 底漆、头道漆 Finish coat 面漆Surface coat 表面涂层 Under coat 内涂层 Wearing coat 磨耗层Zinc-rich coating 富锌涂层Cement wash coating （薄）水泥涂层 Stripe coating 预涂层 Floor covering 地板覆层 Alkyd resin paint 醇酸树脂漆Epoxy(resin-based)paint 环氧树脂涂料 3 船舶专业英语词汇（初级） Scuttle 舷窗 Carpet 地毯Wooden skirt 木裙板（踢脚）Aluminum skirt 稆质裙板（踢脚） Brass nose 装于楼梯踏步一的黄铜防滑镶条Stainless screw 不锈钢螺钉 Spring 弹簧Securing dev ice 固定件Locking device 闭锁装置，制动设备 Plywood 胶合板，层压板 Laminated plate 迭层板Laminate 层压制品，迭层板，层压板 High pressure washing of the hull 用高压水冲洗船壳Steel plate temperature 钢板温度 Condensation 冷凝Capillary condensation 毛细管现象 Dew point 露点 Flashing point 闪点Ignition point 燃点，着火点 Ventilation for coating 涂装通风 Dehumidifier 去湿机，干燥机 Dehumidification 去湿，去潮 Sagging 流挂，下垂 Chalking 粉化Peeling 剥落（指油漆） Pinhole 针孔 CureCuring 硬化，熟化，硫化 Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature 硬化、固化温度 Power tools 有动力的工具（包括电动及风动）Pheomatic tools 风动工具 Burnt area 烧坏的区域 Oil stains 油迹 Scratches 划痕Damaged places 遭损坏的部位 Chicken wire 钢丝网 Tiles 瓷砖，瓦Mosaic-tile 彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue 胶，粘结剂Silica 硅石，二氧化碳 Silicagel 硅胶Decoration 装饰，装修Interior decoration 内部装饰，内装 Deck head 天花板..Ceiling 天花板Paneling 板墙，镶板 Wall 墙壁Desk 书桌，桌台 Drawer 抽屉Catch hook 固定钩子Observation window 观察窗 Inspection window 检查孔窗 Clear view window 旋转观察窗 Curtain 窗帘Latch 止动销，插销 Valance 窗帘箱 Hanging 窗帘Eyebrow 舷窗眉板 Pre-alarm 预报警 Trip 脱扣，跳闸Preferential trip 优先脱扣 Transducer 换能器synchronize （便）同步 synchronize motor 同步电机 synchronous motor 异步电机 step motor 步进电机 diode 二极管 triode 三极管 audion 三极管 single phase 单相 three phase 三相 phase-in 逐步引进 phase-shafting 相移retarding phase 滞后相位 reversed phase 倒相，相反 relay 继电器 timer 定时器trimmer 微调电容器，调正片 delay 延时carrier 载波，载波电流transponder 发射器，应答器，询问机 echo-sound 回声测深仪radio navigation equipment 无线电导航设备log 计程仪auto-pilot 自动驾驶仪 gyro-compass 电罗经barrier 屏障，障碍，栅栏 zenner barrier 齐纳屏（使电只能单向流的半导体）radio beacon 无线电信标 pluse 脉冲blanking plus 消隐脉冲 induction 感应，感应现象 oscillation 振荡 Leak(v)渗，漏 Leakage(n) 渗，漏Overhaul 大修，彻底检修 Hammer 榔头Spanner 扳手，扳头Ring spanner 环形扳手，梅花扳手 Allen key 内六角扳手， Box spanner 套筒扳手 Torque spanner 扭力扳手Double-ended spanner 双头扳手 Monkey spanner 活络扳手，活络管扳手 Shifting spanner 活络扳手Pipe spanner 管子扳手 Reamer 铰刀Reaming （用）铰（刀扩）孔 Countersink reamer 锥形孔铰刀 Wrench 扳手，扳头 Shisel 凿子Calipers 卡钳，两脚规 Inside calipers 内卡钳 Bore 内孔Boroscopic inspection 内孔表面检查 Boroscope 内孔表面检查仪 Plug 塞（子），（内燃机）火花塞 Cock 施塞，龙头 Valve 阀P/V valve P/V 阀 Strainer 滤器Coarse strainer 粗滤器 Fine strainer 精滤器 Oil separator 分油机 Back pressure 背压 Pressure test 压力试验 Over speed 超速 Over load 超负荷Dafety device 安全装置 Fly wheel 飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的） Ladder 梯子Vertical ladder 直梯 Inclined ladder 斜梯Accommodation ladder 舷梯 Pilot ladder 引水员；软梯 Centering 对中心Alignment 对准，对准中心 Inspection 报验 Installation 安装Final inspection of M/E insallation 主机最终安装报验Inspection of the centering of the stern tabe before fine boring 精镗前艉轴管中心校准Alignment check/inspection 拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system 燃油管串油后清洁检查 Function test of steering gear 舵机效甩试验Hose test of water tight doors 水密门冲水试验Noise lever measurement 噪声测量 Vibration level measurement 振动测量 Main engine (M/E)主机 Generator 发电机Emergency generator 应急发电机 Shaft generator 轴带发电机 Fresh water generator 制淡装置 Steering gear 舵机General service pump 总用泵 Pire pump 消防泵Hydraulic motor 液压马达Hydraulic nuts 液压螺帽 Rudder 舵Rudder bl ade 舵叶Propeller 车叶，螺旋桨Fixed pitch propeller 固定螺距的螺旋桨 Lofting 型线图放样Lay off （船及部件）放样，下料 Plate-cutting 钢板下料，开工Numerically-controlled cutting machine 数控切割机Cutting machine 切割机Under water plasma cutting machine 水下等离子切割机Surface preparation 表面处理 Fabrication （焊）开坡口，边缘加工（如刨边）Upside down construction method 分段装配Assembly 反身建法 Erection 装配，大合拢 Jig 装配架，胎架 Bow jip 船首部胎架Girder 纵向构件，桁（材） Beam 梁，横梁 Sections 型材Profile 型钢（条） Bar 杆，棒,棒材 Plate 板材 Angle bar 角钢I beam （窄缘）工字梁 H beam （宽缘）工字梁 Stiffener 扶强材Bracket 托架，支架，肘板 Support 支架Frame 肋骨，框架 Douler 复板Coaming （舱口）围板，缘材 Sinp 剪切 Cut 切割 Anchor 锚Anchor widdlass 锚机 Anchorage 锚位，锚地 Chain 链Chain block 链条滑车，神仙滑车 Platform 平台Crossover 跨越（梯桥），立交 Life raft 救身筏 Life buoy 救生圈Forward winch 前绞缆机 After winch 后绞缆机 Windlass 锚机 Bitt 带缆桩，系桩Fairlead 导缆钳，导缆孔 Hand rail 扶手，栏杆 Beam 横梁Frame 肋骨，框架 Scantling 构件尺寸 Cargo oil tank 货油舱 Scantling draft 结构吃水 Forepeak tank 首尖舱 After peak tank 尾尖舱Water ballast tanks(W.B.T)压载水舱 Fuel oil tank(F.O.T)燃油舱..Lubricating oil tank(L.OT)滑油舱 Diesel oil tank(D.O.T)柴油舱 Double botton 双层底Double skin 双层外板，双层蒙皮 Bow thruster 艏侧推 Propeller 车叶Fixed pitch propeller 定螺距螺旋桨 Controllable pitch propeller(CPP)可调螺距螺旋桨 Shaft 轴Tail shart 尾轴Shaft generator 轴带发电机 Watertight doors 水密门 Bulwark 舷墙 Bulkhead 舱壁Tank top 内底，液舱顶 Hatch cover 舱口盖 Manhole 人孔Fin stablizer 减摇鳍Antifouling system 防海生物的，防污染系统 Ship 船Vessel 船，舰Fabrication 制造，分段装配（precfabrication 预制，预加工） Assemble 装配，组装Erection 大合拢，船台装配 Staging 脚手架Block stage 分段阶段Mile stone （里程碑，大节点） Plate-cutting 下料，开工Keel-laying 上船台，龙骨铺设 Lauching 下水mooring trial 码头试验，系泊试验 sea trial(sea)试航delivery of the ship 交船defect list by the owner/society 船东提出的消除意见清单/船级社提出的消除意见清单design stage 设计阶段submit drawings to owner,classification society(LR 、DNV 、BV 、ABS ，etc)for approval 向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸 hull workshop 船体车间machining workshop 金工车间machinery engineering workshop 轮机车间electrical workshop 电气车间 business dept.经营处 perchasing dept.供应处 Q.C.Dept.检验处 Design dept.设计室 Painting and carpenter ’s workshop 漆木车间Project manager 项目经理 Director 指导者，厂长，董事 Managing director 执行董事，常务董事，总经理Head 首长，团长，主任Manager 经理，管理人，干事 Leader 领导者 Meeting 会议Negotiation 谈判 Agreement 协议 Shipyard 船厂 船舶专业英语词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用 accommodation 居住（舱室） accommodation ladder 舷梯 adjust valve 调节阀adjustable-pitch 可调螺距式 admiralty 海军部advance coefficient 进速系数 aerostatic 空气静力学的 aft peak bulkhead 艉尖舱壁 aft peak tank 艉尖舱 aileron 副鳍air cushion vehicle 气垫船 air diffuser 空气扩散器 air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵 alignment chock 组装校准用垫楔 aluminum alloy structure 铝合金结构 American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的 anchor arm 锚臂 anchor chain 锚链 anchor crown 锚冠 anchor fluke 锚爪 anchor mouth 锚唇 anchor recess 锚穴 anchor shackle 锚卸扣 anchor stock 锚杆 angle bar 角钢angle of attack 攻角 angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷 anti-pitching fins 减纵摇鳍 antiroll fins 减摇鳍anti-rolling tank 减摇水舱 appendage 附体 artisan 技工assembly line 装配流水线 at-sea replenishment 海上补给 augment of resistance 阻力增额 auxiliary systems 辅机系统 auxiliary tank 调节水舱 axial advance 轴向进速 backing structure 垫衬结构 back-up member 焊接垫板 balance weight 平衡锤ball bearing 滚珠轴承 ball valve 球阀ballast tank 压载水舱 bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨 barge 驳船 baseline 基线basic design 基本设计 batten 压条，板条 beam 船宽，梁beam bracket 横梁肘板 beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线 Benoulli ’s law 伯努利定律 berth term 停泊期 bevel 折角 bidder 投标人 bilge 舭，舱底bilge bracket 舭肘板 bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩 blade root 叶跟blade section 叶元剖面 blast 喷丸block coefficient 方形系数 blue peter 出航旗boarding deck 登艇甲板 boat davit 吊艇架 boat fall 吊艇索 boat guy 稳艇索 bobstay 首斜尾拉索 body plan 横剖面图 bolt 螺栓，上螺栓固定 Bonjean curve 邦戎曲线 boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁 bottom side tank 底边舱 bottom transverse 底列板 boundary layer 边界层 bow line 前体纵剖线 bow wave 艏波 bowsprit 艏斜桅bow-thruster 艏侧推器 box girder 箱桁bracket floor 框架肋板 brake 制动装置 brake band 制动带brake crank arm 制动曲柄 brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽，计算宽度 breadth moulded 型宽 breakbulk 件杂货 breasthook 艏肘板 bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会..buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材 bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首 bulk carrier 散货船bulk oil carrier 散装油轮 bulkhead 舱壁 bulwark 舷墙bulwark plate 舷墙板 bulwark stay 舷墙支撑 buoy tender 航标船 buoyant 浮力的 buoyant box 浮箱Bureau Veritas 法国船级社 butt weld 对缝焊接butterfly screw cap 蝶形螺帽 buttock 后体纵剖线by convention 按照惯例，按约定 大秦cable ship 布缆船 cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱cant beam 斜横梁 cant frame 斜肋骨cantilever beam 悬臂梁 capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆capsizing moment 倾覆力臂 captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积 cargo handling 货物装卸 carriage 拖车，拖架cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心 chain cable stopper 制链器 chart 海图charterer 租船人chief engineer 轮机长 chine 舭，舷，脊 chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论 classification society 船级社 cleat 系缆扣clipper bow 飞剪型船首 clutch 离合器coastal cargo 沿海客货轮 cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船 commuter 交通船 compartment 舱室 compass 罗经concept design 概念设计 connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨 constraint condition 约束条件 container 集装箱containerized 集装箱化 contract design 合同设计contra-rotating propellers 对转桨 controllable-pitch 可控螺距式 corrosion 锈蚀，腐蚀 couple 力矩，力偶 crane 克令吊，起重机 crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱 criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积 crow ’s nest 桅杆瞭望台 cruiser stern 巡洋舰尾 crussing range 航程cup and ball joint 球窝关节 curvature 曲率curves of form 各船形曲线 cushion of air 气垫damage stability 破损稳性 damper 缓冲器 damping 阻尼 davit arm 吊臂deadweight 总载重量 de-ballast 卸除压载deck line at side 甲板边线 deck longitudinal 甲板纵骨 deck stringer 甲板边板 deck transverse 强横梁deckhouse 舱面室，甲板室 deep v hull 深v 型船体 delivery 交船 depth 船深derrick 起重机，吊杆 design margin 设计余量design spiral 设计螺旋循环方式 destroyer 驱逐舰detachable shackle 散合式连接卸扣 detail design 详细设计diagonal stiffener 斜置加强筋 diagram 图，原理图，设计图 diesel engine 柴油机dimensionless ratio 无量纲比值 displacement 排水量displacement type vessel 排水型船 distributed load 分布载荷 division 站，划分，分隔 do work 做功 dock 泊靠double hook 山字钩double iteration procedure 双重迭代法 double roller chock 双滚轮式导览钳 double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索 draft 吃水drag 阻力，拖拽力 drainage 排水draught 吃水，草图，设计图，牵引力 dredge 挖泥船 drift 漂移，偏航 drilling rig 钻架 drillship 钻井船 drive shaft 驱动器轴driving gear box 传动齿轮箱 driving shaft system 传动轴系 dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计 e.h.p 有效马力eccentric wheel 偏心轮 echo-sounder 回声探深仪 eddy 漩涡eddy-making resistance 漩涡阻力 efficiency 供给能力，供给量 electrohydraulic 电动液压的 electroplater 电镀工 elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔 empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇 end open link 末端链环 end shackle 末端卸扣 endurance 续航力endurance 续航力，全功率工作时间 engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆 entrance 进流段erection 装配，安装 exhaust valve 排气阀expanded bracket 延伸肘板 expansion joint 伸缩接头 extrapolate 外插 fair 光顺faised floor 升高肋板 fan 鼓风机 fatigue 疲劳feasibility study 可行性研究 feathering blade 顺流变距桨叶。
1．您好！（第一次见面）How do you do?2．您好！见到您很高兴。
How do you do? I’m very glad to meet you.3．让我来介绍一下在座的各位先生。
林先生，我们厂的厂长；王先生，厂长总工；吴先生，船体车间主任。
Let me introduce the gentlemen present here. This is Mr.Lin, our shipyard manager; Mr.Wang, our chief engineer. Mr.Wu, director of the hull shop.4．欢迎您到我们船厂来！welcome to our shipyard!5．请坐！Sit down please.6．好的，谢谢！Thank you.7．请喝茶。
Please have a cup of tea.8．喂，您好吗？（熟人之间）Hi, how are you?9．很好，谢谢。
您好吗？Fine, thank you, and how are you?10．很好，谢谢！V ery well, thanks.11．我们现在就开始工作好吗？Shall we start our work now?12．好的。
OK .13．请这边走。
This way, please.14．我可以进来吗？May I come in?15．请进！Yes, please.16．早晨好，女士。
Good morning, ma’am (Madam).17．早晨好，布莱克先生。
请坐。
Good morning, Mr.Blake. take a seat, please.18．谢谢！Thank you, ma’am.19．请问您有什么事和我商讨？What business would you like to talk with me about? 20．船东想在船上做些变化。
The ship owner wants to make some changes in the hull. 21．这样的事，我只能晚些时候回答您。
VOCABULARY3-roller bending machine 三弯机abandon v. 弃船abolish v. 消除ABS 美国船级社acceleration n. 加速度accelerometer n. 加速度表accommodate v. 容纳accommodation deck起居(住舱)甲板accuracy n. 精度accurate synchro device准同步装置acetylene cutter 气割机acid-pickling n. 酸洗acoustics n. 音响效果adhesiveness n. 粘附力adjacent a.相邻的adjust v. 调节administration n. 行政管理admit v. 接纳adopt v. 采纳，采用affiliated factory 分厂，附属工厂aforementioned a.前述aft a. adv. n. （在）船艉aft peak 艉尖舱after service 售后服务ahead n. 正车air bottle 空气瓶air compressor 空压机air reservoir 气瓶air siren 汽笛air-tight test 气密实验alarm bell 警铃alignment n. 找中all waves 全波allowance n. 允值all position 全方位alternating current ( A.C.) 交流电ammonia n. 氨amplify v. 放大an automatic production line自动生产线analogous output 模拟输出analogue computer 模拟计算机anchor n. 锚anchor chain （cable chain）锚链anchor handling 锚操纵anchor windlass (chain windlass) 起锚机anchorage buoy 系泊浮筒angular n. 角度antenna n. 天线anticorrosion precaution 防腐措施apparatus n. (pl. apparatus or apparatuses)仪器，器械，装置appearance n. 外观approval n. 批准，认可approve vt. 认可arbitrate v. 仲裁arc n. 弧度arduous a.艰难的arrange v. 布置，安排asbestos n. 石棉assemble v. 装配Assemble Language 汇编语言assembly n. 装配astern n. 倒车atmospheric survey 大气环流调查atomic power 原子能atomize v. 雾化authority n. 当局automatic control device自动控制装置automatic production line自动生产线automatic steering 自动操舵automatic submerged arc welding自动埋弧焊automatic telephone 自动电话aux. boiler 副锅炉aux. engine 辅机aux. engine room 辅机舱aux. machinery 辅机auxiliary means 辅助手段auxiliary system 辅助系统axial push 轴向推力backing n. 衬垫ballast piping 压载水管系ballast pump 压载泵ballast system 压载系统ballast water 压载水base n. 基准base point n. 基准点basic design 基本（方案）设计basic metal 母材battery unit 蓄电池组beam n. 波束beam n. 横梁bearing n. 轴承bearing hole n. 轴承孔bedplate n. 机座bell set 铃组bending machine 冷弯机berth n. (水平)船台，（船上）床铺berth or slipway fabrication船台装配bilge n. 舱底水bilge keel 舭龙骨bilge plate 舭板bilge pump 舱底水泵bilge system 舱底水系统binary system 二进位制blank n. 毛胚block n. 分段block or section fabrication分段或总段装配blood vessel 血管blower 风机blue collar worker 蓝领,工人boat deck 艇甲板bollard n. 带缆桩bolt n. 螺栓bolthead n. 螺栓头bottom n. 船底bottom plate 底板bottom structure 底板结构bow n. 船艏bow &stern structure 艏艉结构bow section 艏段branch company 分公司，子公司branch system 分系统bridge n. 桥楼bridge control 桥楼控制broadcast n. v. 广播broadcast station 广播站bronze sleeve 青铜套筒bulbous bow 球鼻艏bulk cargo 散装货物bulk-cargo carrier 散装货船bulkhead n. 隔舱壁bulkhead structure 隔舱壁结构bushing n. 衬垫butt joint 对接接头cabin n. 舱室cable fixture 电缆夹具calculation n. 计算calculator n. 计算器calibrate v. 校正calibration n. 校正cam n. 凸轮cam follower 凸轮附件camber n. 梁拱camshaft n. 凸轮轴capstan windlass（anchor winch）锚绞盘cargo n. 船货cargo oil 货油cargo –hold n. 货舱cargo-lifting n. 起货casing n. 罩壳cast iron piece 铸铁件casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n.性能，特性，特征charge v. 充（电，气）check n. v. 检验chemical medium 化学介质China Classification Society(CCS)中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子，团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环clutch n. 离合器CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity综合生产能力compressed air 压缩空气compression (power)stroke n.压缩冲程computer control console计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contract n. 合同contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养，培育current n. 电流current n. 洋流，水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n.载重量，吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货，交船delivery n. 交船，交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称，牌号designation n. 目的地detail design 详细（施工）设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone对讲电话，直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端，争执distribute v. 分布distribute v. 分配，配电distribution n. 配电distribution box 分电箱distribution panel 区配电板distribution switch 配电开关distribution system n. 配电系统division n. 划分DNV 挪威船级社Dock n. 船坞dock trial 码头试验docking winch 带缆绞车Doppler effect 多普勒效应Doppler frequency offset多普勒频移Doppler sonar log多普勒声纳计程仪double bottom 双层底double-action a.双作用down-vertical welding 下行焊draft(draught)n. 吃水drainage n. 疏水，泄水drawing n. 图纸drawing instrument 绘图仪drift v. 漂移drinking water 饮用水drip-proof type 防滴式drive n. 传动drive mechanism 传动机构drive mechanism 传动装置drive unit 传动装置driven shaft 从动轴dry v. 烘干drydock n. 干船坞dynamic –pressure type 水压式echo signal 返回信号echo sounder 回声测深仪economic effect 经济效益edge preparation 边缘加工edge processing 边缘加工edger n. 刨边机eject v. 喷射elapse v. （时光）消逝electric brain 电脑electric load 负荷electrical arc 电弧electrical compass 电罗经electrical drive 电力托动electrical energy 电能electrical impulse 电脉冲electrical power 电力electrical shedding 放电electrical signal 电器信号electrical slag welding 电焊渣electrical unit 电器装置electrical user 电器设备electrical-driven a. 电动的electrician n. 电工electricity outfitting 电舾electrode n. 焊条electromagnetic contactor电磁接触器electromagnetic induction 电磁感应electromagnetic log 电磁计程仪electromagnetic sensor 电磁传感器electronic computer 电子计算机electronics n. 电子（学）element n. 机械零件element n. 要素emerge v. 崛起，兴起emergency control 应急控制emergency network 应急电网emergency power station 应急电站emergency radio transmitter应急无线电发信机emergency steering 应急操舵emergency switchboard 应急配电板emergency telegraph 应急传令钟emergent discharge 应急排放emergent service 应急使用enclose v. 封闭encounter v. 遭遇energy convertor 换能器engine foundation (engine seat )机座engine frame 机架engine oil 机油engine outfitting 机舾engine space 机舱engineer n. 轮机员engineer n. 工程师engineering and technical team工程技术队伍engineer vessel 工程船engine-room 机舱ensure v. 确保enterprise n. 企业EO 无人机舱equipment n. 设备error n. 误差essence n. 实质，本质evolve v. 渐进，进化，演变excessive a. 过量的，极度的excitation n. 励磁excite v. 激励exhaust port 排气口exhaust stroke 排气冲程exhaust valve 排气阀expand v. 扩张，扩建expansion n. 展开图expansion stroke 膨胀（作工）冲程expansion tank 膨胀箱experiment n. 实验exterior force 外力extinguish v. 灭火F.O.meter 燃油流量计F.O．tank 燃油舱Fabricate v. 装配，制作fabrication n. 装配facile adaptability 灵活的适应性facsimile transmission(fax)传真fairing n. 光顺体，流线体fair-lead n. 导缆孔fashioned steel 型钢fast speed (rapidity)快速性fathometer n. 侧深仪feed v. 馈给feed circuit 馈电线路fillet seam 角焊缝fillet welding 角焊filter n. 过滤器. 过滤fine a. 纤细的finished product 成品fire alarm 火警fire hazard 火灾fire pump 消防泵fire-fighting system 消防系统fire-resistant a.耐火的fixed part 固定件flash signal light 闪光信号灯flat fillet seam 平角焊缝flexibility n. 挠性flexible coupling 挠性联轴节float launching 漂浮下水floatability n. 漂浮性floating positively 正浮floating production storage unit(FPSU)浮式生产储油轮flood v. 进水floodability n. 不沉性floor plate 肋板fluctuate v. 波动fluctuation n. 波动flush v. 清洗flushing agent 清洗剂flux n. 焊剂flywheel n 飞轮foam n. 泡沫folding machine 折边机for home use 国内用forced lubrication 强制润滑forced ventilation 机械通风fore perpendicular 艏垂线forecastle n. 艏楼foreign trade 外贸forging n. 锻造formation n. 构成，结构frame n. 肋骨framework n. 框架framing block 肋骨框架分段free end 自由端freeboard n. 干舷freighter n. 货船Freon n. 氟利昂frequency n. 频率frequency difference latching频率锁定frequency regulation 调频fresh water （F.W.）淡水fresh water production plant造水装置friction resistance 摩擦阻力fuel n. 燃料fuel nozzle 喷油嘴fuel oil 燃油fuel oil （F.O.）燃油fuel pipeline 燃油管系full-load a. 满载的full-load displacement 满载排水量funnel n. 烟囱galley n. 厨房gantry n. 龙门架gas cutting 气割gas tight seal 气密密封gas turbine engine 燃气轮机gas welding 气焊gear n. 齿轮gear drive 齿轮转动geo-physical propecting vessel地球物理探测船GL 西德劳氏船级社grant v. 给予……的权利gravity centre 重心gravity welding 重力焊groove v. 开坡口ground v. 接地group n. (企业)集团growth n. 生长，发育guarantee n. v. 保证general description 概述general-purpose a.通用的generating set 发电机组geometrical characteristics 几何特征geometrical principle 几何原理gravity launching 重力下水guided-missile frigate 导弹护卫舰gyro n. 陀螺仪gyro compass 陀螺罗经，回转罗经H.D.Heavy Machinery Co. Ltd. H.D. 重机股份有限公司Halogen n. 卤素hand control 手控hand level 手柄hand steering 手动操作hand wheel 手轮handle v. 操纵harbour n. 港口，停泊harbour generator 停泊发电机hardware n. 硬件hatch trunk 舱口围壁hawsepipe n. 锚链筒he water pressure system 水压系统headquarters n. 总部，厂部headroom n. 甲板间高度heat exchanger 热交换器heating n. 供暖heavy current n. 强电heavy oil 重油heel n. 横倾hereinbelow adv. 在下文high frequency 高频high-speed boat 高速艇horizontal a.水平的，卧式的horsepower(hp) n. 马力hose n. 软管hot processing 热加工hot work 火工hull n. 船体hull cleanness 船体光顺性hull construction 船体结构hull form 船型hull line 船体线型hull structure 船体结构human brain 人脑humidify v. 增湿hydraulic a. 液压的hydraulic fluid 液压流体hydraulic machine 液压机hyperbolic curve receive双曲线定位仪identify vt.识别ignite v. 点火ignition n. 点火illumination n. 照明illustration n. 生动的说image display system 图象显示系统IMCO 政府间海事协商组织impact n. 冲击implication n. 含义impulsator n. 推动器，脉冲发生器impulse-type a.脉冲式的impurity n. 杂质inclination n. 倾斜inclination test 倾斜试验incline v. 倾斜index n. 索引indication n. 显示indicator n. 显示仪indicator n. 指示器indicator light 指示灯indicator valve示功阀inert gas 惰性气体inertia n. 惯性inertia platform 惯性平台inevitable a.不可避免的initial metacentric height 初稳心高inject n. 喷射injecting system 喷油系统injector n. 喷油器inner bottom longitudinal 内底纵骨inner bottom plate 内底板inner ring 内环input n. v. 输入inspector n. 质检员installation n. （船上）安装installation error 安装误差instancy speed 瞬时速度instrument n. 仪表,仪器insulating material 绝缘材料insulation n. 绝缘intake n. 吸入intake port 汲气口intake valve 进气阀integral casting 整体浇铸intention n. 意向intercommunication (intercom)n.内通，内部通讯interfering moment 干扰力矩intermediate bearing 中间轴承intermediate shaft 中间轴internal combustion engine 内燃机international authorities 国际当局Internet 因特网（国际互连网）introduce v. 引进，引入，介绍iron powder electrode 铁粉焊条jig n. 胎架joint design 联合设计journal n. 轴颈keel n. 龙骨keel plate 龙骨板keep station 定位kerosene test 煤油实验key enterprise 骨干企业kilohertz 千赫kinetic energy 动能knot n. 节labyrinth n. 迷宫，曲径land-based a. 路基的landing-place n. 码头lap joint 搭接接头large-computer(mainframe computer) n. 大型（计算）机，主机lay v. 敷设length n. (一)节，（一）段level n. 液位level gauge 液位计level relay 液位继电器license n. 许可证life line 生命线life-belt n. 救生圈life-boat n. 救生艇life-jacket n. 救生衣life-or-death a.生死攸关的life-raft n. 救生筏life-saving n. 救生lifting capacity 起重能力light current 弱电lighting n. 照明light-ship displacement (light-load displacement)轻载排水量lines lofting 线型放样lines offsets 型值lines plan 线型图lining n. 衬垫load distribution 负荷分配load line mark 载重线标志load transfer 负荷转移local strengthening 局部加强locate v. 定位lock washer 锁紧垫片lofting n. 放样log n. 计程仪logical a.逻辑的long bridge 长桥楼longitudinal a.纵向的longitudinal (uniflow)scavenge直流扫气longitudinal bulkhead 纵隔舱壁longitudinal framing 纵向构架loop n. 回路loop antenna 环状天线Loran receiver 劳兰定位仪Loudspeaker n. 扬声器low speed 低速lower deck 下甲板LR 英国劳氏船级社lube oil 润滑油lube oil(L.O.)滑油lube oil pump 滑油泵lubricant n. 润滑剂lubricant film 润滑油膜lubricating oil 滑油lubrication system 滑油系统M.E.engine room 主机舱Machine v. 机加工machinery n. 机械machinery set 机组machinery workshop 机电车间machining n. 机加工machining workshop 机加工车间magnetic compass 磁罗经magnetic field 磁场magnetic needle 磁针magnetic object 磁性物体magnifier n. 放大器magnify v. 放大magnitude n. 大小main bearing 主轴承main engine (ME) 主机main generating set 主发电机组Main Group 1 第一大部分main hull 主船体main network 主电网main power station 主电站main switchboard 主配电板maintenance n. v. 维护，保养marker n. 厂商man power resource 人力资源management n. 生产管理maneuver v. n. 操纵maneuverability n. 操纵性maneuvering console 操纵台maneuvering system 操纵系统manual work 手工劳动manufacture n. &v. 生产，制造marine crane 船用起重机marine diesel engine 船用柴油机marine engineer 机电工程师marine engineering research institute造机研究所marine geological research vessel海洋地质调查船mark v. 标出mast lightmaster controller 主令控制器Master degree 硕士学位material n. 材料material marking 下料mathematical a.数学的mathematical lofting skill数学放样技术maximum(max.)n. 最大means n. 手段，工具measurement laboratory 计量实验室measuring meter 测量仪表measuring point 测量点mechanical energy 机械能mechanical launching 机械下水mechanical processing 机加工mechanical unit 机械装置medium speed 中速medium wave 中波medium-computer n.中型（计算）机member n. 构件memory n. 储存器，内存memory and storage system储存系统merchant ship 民用船mercury n,水银meridian n. 子午线metacentre n. 稳心metal recovery 金属回收率metallic equipment 冶金设备microclimate n. 小气候microcomputer n. 微机microprocessor n. 微处理器midship n. a. adv. 舯部military ship 军用船miller n. 铣床minicomputer n. 小型（计算）机minimize v. 降至最低minus push 负推力minus value 负值miscellaneous a. 杂项的mobilize v. 动员model case 样箱model plate 样板model rod 样棒moderate a. 中型的modern enterprise system现代企业制度modus n. 操纵法（pl. modi）monitor v. 监视monitoring device 监控装置moor v. 系泊motive power 原动力motor n. 电动机mould loft 放样台mouth n. 河口moving part 运动件multi-purpose a.多用途的，综合的multi-stage n. 多级mutual benefit 互惠互利nautical mile 海里naval architect 造船设计师navigating instrument 导航仪器navigating zone 航区navigation computer 导航计算机navigation equipment 导航设备navigational light 航行灯navy n. 海军navy underway replenishment ship海军航行补给船NC cutting machine 数控切割机nerve cell 神经细胞nesting n. 套料network n. 电网nil n. 零，无NK 日本海事协会non –ferrous metal 有色金属non-restrictive a.自由的，不受限制的non-standard product 非标产品non-transparent a. 不透明的normal displacement 正常排水量normal shipping 正常营运nozzle n. 喷嚏numbering system 计算系统numeral n. 数字numerical control (NC)数控numerical control cutter 数控切割机nut n. 螺母observation n. 观察occasion n. 盛事，盛举ocean-going vessel 远洋船oceanographic research vessel海洋调查船offshore service 近海作业oil charging piping 注油管系oil consumption 油耗oil filling port 注油口oil mist 油雾oil refinery 炼油厂oil tanker 油船oil-resistant a.耐油的oil-tight n. 油密Omega/satellite integrated navigation instrument 奥米加/卫星导航系统one-side welding单面焊接，双面成形one-way a.单向的open chamber 开放式燃烧室open circulation 开放循环opening n. 开口operating cycle 工作周期operation n. 施工operation n. 运行，运转operation surroundings 作业环境operator n. 操纵员opportunity n. 机遇optical projector 光学仪器optics n. 光学orbit n. 轨道order n. v. 订单，定购oscillation n. 振荡oscillation current 振荡电流outboard adv. 向舷外outer appearance 外观outer ring 外环outfitting n. 舾装output n. 输出overload v. 过载owner n. 船东owner’s representative船东代表oxide n. 氧化皮paint n. 油漆pain-taking a.艰巨的painting n. 涂装painting n. 涂装，油漆工艺palletizing management 托盘管理parallel n. 并联v. 并车parallel of generators 发电机并车parameter n. 参数part n. 部件，机械部件part fabrication 部装particle n. 颗粒party n. (谈判或合同之)一方passage n. 通道passageway n. 通道passenger-cargo vessel 客货船performance n. 性能permanently adv. 永久的perpendicular n. 垂线personnel n. 全体人员personnel n. 人员，人事phase angle 相角phase sequence 相序phase –sensitive rectifier相敏整流器physical quantity 物理量physical-chemical experiment理化实验physical-chemical experimental center理化中心实验室pillar n. 支柱pilot n. 驾驶员，领航员，舵轮pipe connection 管子接头pipe flange 管子法兰piping system 管系piston pin 活塞环piston pin 活塞梢piston stroke 活塞冲程pitch n. 纵摇plan n. 图纸plane n. 平面plane v. 整平planing machine 校平机plant n. （成套机电）设备platform n. 平台pneumatic tool 气动工具pointing of direction 指向poisonous gas 有毒气体pollution n. 污染poop n. 艉楼port n. 左舷portable light 手提灯postdoctoral centre 博士后工作站potable water 饮用水pour v. 涌入，源源不断power amplifier 功率放大器power plant 动力装置,(火力)电厂power station 电站power supply 电源，供电power system 电力系统,动力系统practice n. 习惯做法preamplifier n. 前置放大器pre-combustion chamber预燃燃烧室pre-heat v. 预热pressure container 压力容器pressure relay 压力继电器pressure sensor 压力传感器pressure tank 压力柜pretreat v. 预处理primary radio transmitter主无线电发信机prime mover 原动机primer n. 底漆primer painting 涂底漆principle dimensions 主尺度process n. 工艺，流程v. 加工，处理production efficiency 生产效率production line 生产线production procedure 生产程序program n. 程序projection plane 投影面prolong v. 延长promote v. 促进，晋升propeller n. 螺旋桨proportion n. 比例propulsion efficiency 推进效力propulsion plant 推进装置protection type 保护式provision n. 食品pump n. 汞purity v. 净化push rod 顶杆push-pull magnetic amplifier推挽磁放大器pyramid method 正装法quality assurance 质量保证quality control 质量控制quality management 质量管理quality policy 质量方针quay n. (顺岸式)码头quiescent a.安静的radar n. 雷达radio beacon station 导航台radio communication equipment无线电通讯设备radio directional finder 无线电测向仪radio message 无线电报radio receive 无线电接收机radio room 报房radio station 电台radio transmitter 无线电发信机radio wave 无线电波range n. 航程range v. 测距range display 航程显示器range unit 航程装置rated power 额定功率rated value 额定值reaction n. 反作用力reading n. 读数receiver n. 接收器reciprocating movement 往复运动rectification n. 矫正，整顿rectify v. 整流，滤波reduction gear 减速齿轮reduction gearbox 减速齿轮箱reduction unit 减速装置reduction with an astern clutch带到车离合器的减速reefer n. （俗）冷藏船，冰箱reflect v. 反射refrigerating plant 制冷装置register n. (机)验船师register vt. 登记，注册regulation n. 登记regulator n. 调整器relative humidity 相对湿度relative motion 相对运动relay contactor 继电器remains n. 残余remote control 遥控remote control station 遥控站rescue v. n. 救援rescue frequency 救援频率rescue transmitter 救援发信机resemble v. 相似reserve buoyancy 储备浮力reservoir n. 容器resistance n. 阻力resistance heat 电热阻rest v. 靠左retaining washer 保护垫片retake v. 回收，取回reversal n. 换向reverse v. 反向逆转reverse power 逆功率reversing system 换向机构revolution n. 旋转rigid a. 刚性的ring seam 环缝rock arm 摇臂roll n. 横摇roller machine 滚床room n. 余地rope n. 缆索rotary movement 旋转运动rotate v. 旋转rotating direction 旋转方向rotation n. 旋转度rotor n. 转子rough sea 波涛汹涌roughness n. 粗糙度routine n. 例行公事rpm 转速rudder n. 舵rudder angle indicator 舵角指示器rudder carrier 舵承，舵托rudder stock 舵轴，舵杆rudder stopper 舵角限制器rules n. 规范，规则running n. 经营管理rust preventative 防锈剂rust prevention 防锈rust removal 除锈rust-proof a.防锈的safeguard v. 捍卫safety valve 安全阀salt content 含盐量sanitary water 卫生水saturated steam 饱和蒸汽scavenge v. n. 扫气scavenge box 扫气箱scavenge flow 扫气气流scavenge pattern 扫气型式screen n. 荧光屏screw shaft 螺旋桨轴sea damage 海损sea trial 试航sea water (SW)海水sea-chart room 海图室seakeeping performances航海性能，试航性seal n. v. 密封sealing agent 密封剂sealing gasket 密封垫片sealing ring 密封圈search light 探照灯seasick a.晕船seat n. 座seating n. 基座section n. 总段self excitation 自励self-designed a.自行设计的self-regulated device 自我调节机构semi-conductor n. 半导体SEMT of France 法国热机协会senior engineer 高级工程师sensibility n. 灵敏度separation n. 分离separator n. 分离器serialize vt.使……成系列service n. 公共基础设施service engineer 服务工程师service life 使用寿命service tank 日用柜servo motor 伺服电动机settle v. 沉淀settling tank 沉淀柜shaft bracket 艉轴架，人字架shaft system 轴系shape processing 成形加工shear machine 剪切机shed v. 放射，散发sheer n. 脊弧sheet plate 薄板shell n. 壳板shell plating 外壳列板shell structure 外板结构ship equipment 船舶结构ship general 总体ship outfitting 船舾ship system 船舶系统shipbuilding n. 造船shipbuilding industry 造船工业shipbuilding technology research institute造船工艺研究所shipping n. 航运shipyard(yard)n. 船厂shop trial 车间实验shore electricity box 岸电箱short circuit 短路short wave 短波short-range a.短途的shot-blast v. 喷丸shot-blasting 喷丸处理side n. 船侧side girderside light 舷灯side plate 弦侧板side structure 船侧结构signal n. 信号signal light 信号灯signal processor 信号处理器silicon n. 硅silicon control rectifier(SCR)可控硅single bottom 单底single-action a.单作用single-rudder n. 单舵single-stage n. 单级single-screw n. 单桨site architect 现场造船师site supervisor 现场监控师sketch n. 草图slide-block n. 滑板，导块sliding distance 滑行距离slipway n. (倾斜)船台slipway taper 船台斜面small metacentric angle 小倾角socialist market economy社会主义市场经济software n. 软件soil n. 土壤SOLAS 国际海上人命安全公约SOS 遇难信号sound energy 声能sound insulation 隔音sound power telephone 声力电话sound speed 声速sound wave 声波sounder n. 测深仪sources of power supply 能源space n. 舱室space n. 空间spare gears 备品spare parts(spares)备件special power supply 特种电源speed indicator 航速指示器speed reduction 减速speed servo system 速度随动系统spring n. 弹簧squeeze n. v. 挤压stability n. 稳性stabilizer n. 减摇鳍stabilizing unit 减摇装置staff member 职员stage n. 级stainless steel 不锈钢stand v. 经受standard n. 标准standard displacement 标准排水量stand-by n. 备用stand-by generating set 备用发电机starboard n. 右舷start v. 动身，出发starting system 起动系统starting valve 启动阀state v. 说明state-specified a.部颁的station v. 驻扎steadiness n. 稳定性steam &aux. boiler system蒸汽与副锅炉系统steel plate pretreatment 钢板预处理steel structure 钢结构steel wire 钢丝steering gear 操舵装置steering gear 舵机steering gear room 舵机房steering mechanism 操舵机构steering wheel 舵轮stem n. 艏柱stern n. 船艉，艉柱stern tube 艉轴管stiffener n. 扶强，加强筋storage tank 贮存柜store-room n. 储藏室straight line 直线straight seam 直焊缝strength test 强度试验stringer n. 纵通材structural material 结构材料structure n. 结构，构件stud n. 螺柱stuffing box 填料函subway shield 地铁盾构suck v. 吸入suction (induction) stroke 汲气冲程suction port 吸入口sufficient a.足够的，充足的sum n. (数)二树之和supercomputer n. 巨型（计算）机superstructure n. 上层建筑supervision n. 监督,监造supply vessel 补给，工作船support n. 支撑物surface treatment 表面处理surveyor n. (船)验船师survive v. 幸存，死里逃生sustain v. 支撑，支持swirl chamber 涡流式燃烧室swirl resistance 涡流式阻力switch n. 开关symbol n. 符号symmetrical a.对称的synchro (selsyn)n. 自整角机synchro signal transmitter 自整角机讯号发送器synchronous device 同步装置synchronous follower 同步随动件talent n. 人才，有才能的technical staff 全体技术人员technical force 技术力量technical service 技术服务technical specification (spec)技术规格书technical term 技术术语telegraph n. 传令钟teleprinter n. 电传打字机teleperature relay 温度继电器temporarily adv. 临时地temporary emergency power supply临时应急电源terminal n. 终端testing n. 调试testing facilities 测试设备testing instrument 测试仪器test & trials 试验与试航TEU reefer container ship 冷风集装箱船the ambient air 大气the application software 应用软件the block coefficient 方型系数the brake horse power (BHP)轴马力，制动马力the breath moulded 型宽the central processing unit (CPU)中央处理单元the centralized control room (the controlroom)集控室the controllable pitch propeller (CPP)可调螺距桨the critical path method (CPM) 各种计划节点配合the data base management system (DBMS)数据库管理系统the depth moulded 型深the design water plane 设计水线面the design water plane coefficient设计水面线系数the displacement coefficient 排水量系数the earth magnetic field 地球磁场the effective horsepower 有效马力the fire main 消防总管the fixed pitch propeller 固定螺距桨the future type 未来型the graphic processing software图像处理软件the intertia navigation system惯性导航系统the integral stud anchor chain 整体锚链the language system 语言系统the length B.P.两柱间长the length overall 全长the length W.L.水线长the living quarters 生活区the longitudinal prismatic coefficient纵向菱形系数the metacentre of transversal inclination 横倾稳心the middle longitudinal cross section舯横剖面the midship transversal cross section coefficient 舯横截面系数the net registered tonnage 净登记吨位the North Pole 北极the office automation (OA)办公自动化the operating system (OS)操作系统the painting outfitting 涂装the parties concerned 有关方面the propulsion plant 推进装置the rated frequency 额定功率the rated horsepower 额定马力the roll period 横摇周期the satellite navigation system卫星导航系统the system software 系统软件the total longitudinal bend 总纵弯曲the total longitudinal strength 总纵强度the total tonnage 总吨位thermal mechanism 热力机械thermal stress 热应力thermometer n. 温度计thread v. 攻螺纹thrust bearing 推力轴承thrust end 推力端thrust ring 推力环thrust shaft 推力轴thyristor n. 硅可控整流器，可控硅tier n. （船）层TIG钨极惰性气体焊tightness test 密性试验time vt. 确定……的时间timing gear 准时机构title n. 职称，头衔tonnage n. 吨位top people 上层人物top side plate 弦侧顶板torsional vibration 扭振torsional moment 扭距TQC全面质量管理transceiver n. 收发报机transfer pump 输送泵transistor amplifier 晶体管放大器transistor controller 晶体控制器transistor loop 晶体管回路transmitter n. 发射机,发送器transportation n. 输送transversal a. 横向的transversal bulkhead 横隔舱壁transversal scavenge 横流扫气transversal stability 横稳性treatment plant 处理装置trend n. 趋势trial-and-error a.反复的通过试验找出错误的trim n. 纵倾trunk-piston n. 筒形活塞T-type joint T型接头tuition n. 学费turbine oil 透平油turbocharger n. 涡轮废气增压器turning ability 回转性turning circle 回转半径turning gear 盘车机构turning motion 回转twenty-foot equivalent unit (TEU)20英尺国际标准集装箱twin-engine incoporation 双机并车twinkle v. 闪烁twin-rudder n. 双舵twin-screw n. 双桨two-way a. 双向的ultra short wave 超短波UMS 无人机舱under voltage 欠电压uneven a. 不均匀uniform a. 均匀的unload v. 卸载upper deck 上甲板upset v. (船只)倾覆vacuum n. 真空validate vt. (使)生效valve mechanism 阀机构vaporize v. 汽化velocity n. 速度ventilating pipe 通风管ventilation &air-conditioning system通风与空调系统ventilator n. 通风机vertical a. 垂直的，直立式的vertical seam 垂直焊缝vertical welding 立焊vibration n. 振动viscosity n. 粘度visible range 视距visual telegraph 灯光传令钟visual-acoustical signal 灯光音响信号voltage n. 电压voltage latching 电压锁定voyage n. 航行waste heat 余热water head 压头water inlet pipe 进水管water jacket 水套water pressure test 水压试验water supply 水源，自来水water supply system 供水系统water vapour 水蒸气waterline 水线watertight a. 水密的water-tight test 水密试验wave impact 波浪冲击力wave-forming (wave-making) resistance兴波阻力wear n. v. 磨损weather post 露天部位weight calculation 重量计算welder n. 焊工，焊机welding n. 焊接welding laboratory(lab)焊接试验室welding machine 焊机welding procedure 焊接方法（工艺）welding seam 焊缝welding wire 焊丝well adv. 完全有理由wheel steering 随从操舵，舵轮操舵wheel house n. 驾驶室whereby adv. 靠那个wing buoyant tank 减摇水舱wire cable 钢索work n. 功working condition 工况working principle 工作原理working schedule 生产进度working site 现场workmanship n. 工艺，流程X-ray photo X光照片yaw n. 偏航角。
船舶英语基本交流用语：一、船舶英语常用词汇及口语有哪些?船舶操作Bow(船头)：船的前部。
Stern(船尾)：船的后部。
Port(左舷)：船的左边。
Starboard(右舷)：船的右边。
Aft(船尾)：指船的后部。
Forward(船头)：指船的前部。
Deck(甲板)：船上的平台。
Hatch(舱口)：甲板上的舱口。
Cabin(船舱)：船上的房间。
Mast(桅杆)：竖立在船上的大杆。
二、船舶英语常用词汇及口语有哪些?海上安全Lifeboat(救生艇)：用于紧急撤离船舶的小艇。
Lifebuoy(救生圈)：用于投掷给落水者的浮标。
Flare(信号弹)：海上紧急求救信号。
Emergency Drill(应急演练)：船上的紧急情况演练。
三、船舶英语常用词汇及口语有哪些?导航和通信Compass(指南针)：用于船舶导航的工具。
Sextant(六分仪)：用于航海定位的测量仪器。
Chart(海图)：海上导航用的地图。
Radio(无线电)：船舶通信工具。
四、船舶英语常用词汇及口语有哪些?天气和海况Wind(风)：空气在地球表面的运动。
Wave(海浪)：海面上的涌动。
Current(海流)：海水在海面上的流动。
五、口语表达All hands on deck!(全体上甲板!)：紧急情况下的呼叫。
Man overboard!(有人落水!)：发现有人落水时的呼叫。
Full speed ahead!(全速前进!)：船舶加速前进时的命令。
学英语难就难在没有耐心、不敢开口这个点子上，总被周围的事物吸引了注意力，总以为自己说不出英语，所以一般的英语学习课程起到的作用非常小，不过外教一对一这样的学习模式刚好可以解决这个事情。
一对一的教学比较有针对性，而且外教会全程引导好多，有效提升学英语的意愿度，真正敢于开口说英语，这是一个非常好的学习状态。
目前市面上，其实能做好外教一对一的机构并不多了，高途英语是其中做的不错的一家，到现在已经做了好几年的线上英语培训，网上的总体评价很高。
船舶英语常用词汇1. abrasive blasting (磨料)喷砂法, 喷砂2. access n.通路, 访问, 入门；vt.存取, 接近3. acknowledge vt. 承认, 答谢, 报偿4. alignment n.排列成行;排列成的行列;结盟；合作（亦作：alinement）；n.队列, 结盟5. annex n. 附件vt. 并吞, 附加6. anti slip n.防滑7. application n.请求, 申请, 申请表, 应用, 运用, 施用, 敷用;应用,应用程序,应用软件8. argument n.争论,辩论,论据,论点,～(for,against),意见9. assembly装配，安装，组装组装件，总成机组，集合,装配,集会,集结,汇编【机】装配;装配车间; 部件, 组(合)件; 成套件; 联合装置10. attachment strap 搭接带, 搭接板11. available adj.可用到的, 可利用的, 有用的, 有空的, 接受探访的12. back strap 背垫条, 衬垫, 垫里, 垫座13. bar 杆,棒,棒材,钢筋,型材,型钢;炉条,(锚链的)横档,闩;【电气】汇流排;柜台,酒吧,快餐柜台;阻拦,禁止 aitch bar工字(形)钢,宽缘工字材 anchor bar 撬锚棒 angle bar 角材,角钢 back(ing) bar 【焊接】垫板,背垫短角材 batten(ing) 舱口压条 bearer bar 托梁,支承梁 bearing (steel) bar 支承钢筋,受力(钢)筋;承重杆,承压条 bolt bar 插销,驻栓;螺柱杆 bounding bar 缘周角材 brass bar 黄铜棒 bulb bar 球缘材,球缘钢 bulb flat bar 球扁钢 bulb-angle bar 球缘角材,球缘角钢 bulb-tee bar 丁字形球缘材,丁字形球缘钢 bulb bus bar 【电气】汇流条,汇流排,母线 channel bar 槽材,槽钢 copper bar 紫铜棒 crow bar 起货钩;橇杆,撬棒 deep (frame) bar 强肋骨 equal-angle bar 等边角材,等边角钢 face bar 面材,缘边角材 fender bar 护舷材(小艇的),护舷木 filler bar 焊条 flat bar 扁材 forged stem bar 锻造首柱 frame bar 肋骨角材,肋骨钢 guard bar 栏杆,扶手,扶栏 H bar 宽缘工字钢,工字钢 half-round bar 半圆钢,半圆材 I bar (窄缘)工字钢 iron bar 扁材,铁条,钢条 L bar 不等边角钢,不等边角材 mo(u)d bar 型材,型棒 pinch bar 撬杆,撬棍,绞盘棒 plain bar 普通角材,平角钢 plain bulb bar 球缘扁材,球扁钢 rack bar 齿条,齿杆 reinforcing bar 钢筋,加强筋 round bar 圆材,圆钢 sectional bar 型材,型钢 square bar 方材,方钢 stop bar 止动条T bar “T”形材,“T”形钢 tooth(ed) bar 齿条,齿杆,齿闩 unequal angle bar不等边角钢,不等边角材 unequal flange[unequal leg] bar 不等边角钢,不等边角材14. barge 驳船，大平底船 covered barge 甲板驳 deck barge甲板驳 derrick barge 浮吊，起重驳 dump barge 非自航驳 flat top barge 平甲板驳 flat bottomed barge 平底驳15. banister n. 栏杆的支柱, 楼梯的扶栏16. batten 样条，万能曲线尺；用板条钉住 batten down 封舱 mrasureing batten 标尺17. bay 舱壁间距，强肋骨间距；集装箱货位，货柜存放器；停泊地，码头区 assembly bay 装配工段 building bay 建造工段 fitting bay 舾装工段 welding bay 焊接工段18. beam n.梁, 桁条, (光线的)束, 柱, 电波, 横梁v.播送19. bearing pad乌金轴瓦, 轴承垫20. bending shackle 锚卸扣21. bevel n.坡口,斜角, 斜角规, 倾斜, 斜面vi.成斜角,开坡口,做成斜边vt.使成斜角 beveling(of the edge) 开坡口,各种形状坡口的加工22. blade 推进器叶片(舢板)桨叶舵板翼叶片刀口n.轮叶,叶片23. blasting n.爆破(作业);鼓风; 吹净;喷丸处理; 喷砂处理24. boltn.门闩, 螺钉, 闪电, 跑掉v.上门闩, 囫囵吞下, 逃跑25. boss(铸锻件表面)凸起部毂，轴毂，轮毂，轴套。
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船尾[adv][prep]abandonment cost 船舶废置成本费用accommodation 居住（舱室）living quarter accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯[adv]amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板Beacon 灯塔，示位标bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth molded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定、公约船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer租船人charterchief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室，间隔舱compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船throughoutdistributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠vtdouble hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水，草图，设计图drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak tank 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forgeforward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修furniture gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse)纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性section moulus 剖面模数sections 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机bow 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮very large crude carrierVoith-Schneider propeller/ propulsion外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity/integrality 水密完整性integrate 整合completeness wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工melterwetted surface 湿表面积winch 绞车mooring winchwindlass 起锚机anchor windlasswing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇二．轮机1． Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).螺旋桨轴（中间轴）机加工尺寸检查。
船舶常用英文词汇1 Abbreviation 缩写2 Aboard 在船上3 About ABT 约，大概4 Above Base Line A/B 在基线上5 Access Hole ACC.HOLE (人)通道口6 Access Ladder 出入用梯子7 Accessibility 可接近性8 Accessory 附属品,零件9 Accommodation Accom. 居住区10 Accommodation ladder 居住区楼梯11 Accommodation Space 居住区域12 Accumulator蓄电池13 Acetylene Gas 乙炔气14 Acid Pickling 酸洗15 Adapter 适配器16 Additional ADD. 额外工作17 Additive 添加剂18 Adhesion Test 附着力试验19 Adjusting Piece Adj. Pc 调整用垫片20 After Peak Bulkhead A.P Bhd 尾尖舱壁21After Peak Tank 尾尖舱22 After Perpendicular A.P 艉垂线23 Afterbody 后部船体24 Afterward AFT 向船尾方向25 Agitation 搅拌26 Air Compressor 空气压缩机27 Air Conditioning Plant 空气调节装置28 Air Ejector 空气排出器29 Air Fuel Ratio 气燃比30 Air Hole A/H 气孔31 Air Horn 气笛32 Air Pipe 空气管33 Air Test 气密实验34 Air Vent head 透气头35 Alignment 中心对齐, 校准36 Allocated Stock Item ASI 分配貯藏资材37 Alternating Current AC 交流电38 Aluminizing 镀铝39 Aluminum Anode 防腐蚀铝40 Ambient Temperature 大气温度41 American National Standards Institute ANSI 42 American Society of Testing materials ASTM 43 Anchor锚44 Anchor Bolt 锚栓，基础螺栓美国标准协会美国材料实验协会45 Anchor Chain 锚链46 Anchor Pattern 基础模式47 Anchor Pocket 锚穴48 Anchor Point 定位点49 Anchor Recess 锚穴50 Angle Valve Ang. V/V 角阀（L型）51 Anode Current 阳极电流52 Antenna 天线53 Anticorrosive Paint 防蚀漆54 Anti-Corrosive Tape 防腐蚀胶带55 Anti-Corrosive Treatment 防蚀处理56 Antifouling Paint 防污漆57 Anti-Skid Bar 防滑棒58 Appendix 附录（单数）59 Approval 认可60 Arc Strike 弧光放电61 Arc Time 发弧时间62 Arrangement ARR'T 布置，排列63 Asbestos 石棉64 As-Built Drawing 最终竣工图纸65 Assembly ASS'Y 装配66 Assembly Line 装配线67 Assembly Stage 装配工程68 Automatic Welding 自动焊接69 "Average Freight Rate Assessmentat the max of Deadweight COT" AFRAMAX AFRAMAX(8万吨位级原油运载船) 70 Back Bead 背面焊接71 Back Gouging 后部表面气刨72 Backing Strip 衬垫73 Backside Undercut 背面咬边74 Balance Weight 配重75 Ballast 安定76 Ballast Control Room BCR 压载控制室77 Ballast Tank 压载舱78 Barrel 桶（158.99升）79 Base Line B.L 基线80 Base metal 母材81 Basic Desigh 基础设计82 Bead 焊珠83 Beam 横梁84 Bedplate 主机座85 Bellmouth 吸入口86 Bellows 风箱87 Bench mark 水准基点88 Bevel 斜角, 坡口89 Bevel Angle 坡口角度90 Bilge hat 舱底污水盖91 Bilge Holding Tank 舱底污水储藏罐92 Bilge Keel BLG.KEEL 舱底龙骨(防摇动) 93 Bilge Plate舭列板94 Bilge Radius 船底弯曲部的半径95 Bilge Well B/W 污水井96 Bill of Material BOM 材料明细表97 Bite Union 辊缝连接接头98 Bitumastic (Bituminous Cement) 沥青99 Blank Plate 板坯，基板100 Bleached Tar 漂白涂料101 Blind Plate 盲板102 Blister 水泡(油漆缺陷)103 Block BLK(B) 分段104 Block Assembly 分段装配105 Block Division BLK DIV. 分段划分106 Block Inspection 分段装配检查107 Blow Hole 焊接气孔108 Bollard 系船柱109 Boottop 水线漆110 Bosun(Boatswain) Store 甲板长仓库111 Both-sides Welding 双面焊112 Bottleneck 瓶颈113 Bottom BTM 船底114 Bottom Block 船底分段115 Bottom Plug 船底旋塞116 Bottom Shell Plating 船底外板117 Bottom Survery 船底检查118 Bow and Stern Construction 船首尾构造119 Bow Construction 船首构造120 Bow Door 船首门121 Bow Thruster 船头推进器122 Bowl 槽,斗,碗123 Bracket BKT OR B 加强筋板，轴板124 Brain Storming 集体研讨，想办法125 Brake Lining 闸衬，刹车面126 Brass 黄铜127 Brazing 铜焊,釬焊,硬焊128 Brazing Socket (釬)铜焊孔129 Breaking Strength 折断强度130 Breakwater 挡浪板131 Breast Hook 船首补强肘板132 Breathing Apparatus 呼吸器133 Bronze Casting 青铜铸件134 Brush Coating 毛刷涂漆135 Brush/Brush Holder 毛刷／毛刷固定器136 Bubbling 起泡137 Building Specification 建造规格书138 Bulb Plate BP 球扁钢139 Bulbous Bow 球鼻艏140 Bulk Carrier B/C 散装船141 Bulkhead BHD 舱壁142 Bulkhead Block 舱壁分段143 Bulkhead Piece 穿舱件144 Bulkhead Plan 舱壁结构图145 Bulkhead Stiffener 扶墙材146 Bulkhead Stool 舱壁托架147 Bulwark 舷墙148 Butt Welding 对接焊149 Butterfly valve 蝶型阀150 Buttock Line B.L 船体纵剖线151 Bypass Valve 旁通阀152 Cabin 船舱153 Cable Clench 电缆结154 Cable Duct 电缆通道155 Cable Tie 电线结束结156 Cable Trunk C.T 主干电缆157 Cableway 索道158 Calibration 标定159 Call Sign 呼号160 Camber 梁拱161 Canvas Cover 帆布蓬布162 Capacity Plan 容载度163 Capesize B/C 蓬角B/C164 Capstan 起锚机165 Car Carrier 汽车运输船166 Carbon Air Arc Gouging 一氧化碳气电弧气刨167 Cargo Control Room CCR 卸货控制室168 Cargo Handling System 货物处理系统169 Cargo Oil Pump货油泵170 Cargo Segregation 货物隔离171 Cargo Space 货物区域172 Carling CARL'G (船的)短纵梁173 Carpenter's Workshop 木工车间174 Cast Iron 铸铁175 Cast Steel 铸钢176 Casting CAST'G 铸造,铸件177 Cathodic Protection 阴极保护178 Catwalk 天桥179 Cause of Defect 缺陷原因180 Caution plate 警告板181 Cavitation 气穴现象182 Center Flange Cent. Flg 中心法兰183 Center Girder 中心梁184 Center Keelson 中心线内龙骨185 Center Line C.L 中心线186 Center of Gravity C.G 重心187 Centrifugal Pump 离心泵188 Ceramic Backing 陶衬189 Certificate Cert. 检查合格证190 Chain Block 手拉葫芦191 Chain Locker C/L, CHAIN LKR 锚链锁192 Chain Pipe 锚链通过的管道193 Chain Stopper 止链器194 Chalk Test 划粉实验195 Chamfer C 倒角196 Chamfering Tool 倒角工具197 Channel CH, H(CH) 槽型钢198 Chart Room 图纸室199 Check Point 检测点200 Check Valve 止回阀201 Checked Plate CHK.PL. 花钢板202 Chemical Cleaning 化学洗涤203 Chemical Tanker 化学制品搬运船204 Chipping Hammer 破石锤205 Christening(naming) Ceremony 命名仪式206 Chronometer 记时计207 Clamp 夹钳208 Class 1 Pipe 一级管209 Class A Fires A级火灾210 Class A-60 Bulkhead A A-60 ?? ?? A-60 区域舱壁211 Class Notation 船级代号212 Classification Certificate 船级证书213 Classification Rule 船级规定214 Classification Society 船级协会215 Clear Height 净高216 Clearance 间隙,空隙217 Cleat 夹板218 Client Request Item CRI 船主要求事项219 Clinometer 倾斜仪220 Closed Circuit Television CCTV 闭路电视221 Coaming COAM'G 舱口板222 Cold Galvanizing 冷电镀223 Collar Plate C.PL 加强板/复板224 Collier/Coal Carrier 运煤船225 Companionway 升降口226 Compartment 隔舱227 Compatibility 兼容性228 Component Assembly COMP.ASS'Y 小组装件229 Compressed Air 压缩空气230 Compulsary Item 必要项目231 Condensate Pump 冷凝泵232 Condenser 冷凝器233 Conning Station 操舵(指挥)位置234 Construction CONST. 建造235 Construction Profile 建筑结构轮廓图236 Consumables 易耗品237 Container Ship 集装箱船238 Control Panel 控制板239 Cooling Fresh Water CFW 冷却淡水240 Coordination 业务调整,相互协调241 Corrective Action Request CAR 对纠正措施的要求242 Corridor 通道, 走廊243 Corrosion Control 防腐方法244 Corrosion Inhibitor 防腐蚀剂245 Corrosion Rate 腐蚀度246 Corrugated Bulkhead CORR.BHD 槽形舱壁247 Cost Insurance and Freight CIF "到岸价(包括货价,运费,保险费)"248 Counter-balance Valve 背压阀, 反平衡阀249 Coupling Bolt 连接器螺栓250 Cowl head Ventilator 帽型通风筒251 Crack 裂纹252 Criteria 基准253 Cross Section 橫截面254 Cross Tie 交叉带255 Crossover Way 交叉通道256 Crude Oil Tanker COT 原油船257 Crude Oil Washing COW 原油清洗258 Cruiser Ship 巡洋舰259 Curing 硬化干燥260 Cutting CUTT'G 切割261 Cutting Drawing 切割图纸262 Cutting Tip 气割嘴263 Cutting Torch 割矩264 D mid (Moulded Depth) 型深265 "D/B W.B.T(Double Bottom Water Ballast Tank)" 双底压载舱266 Daewoo Shipbuilding Quality DSQS 大宇造船舶建造质量标准267 Dangerous Goods 危险货物268 Davit 挂艇架269 Daytime 日间, 白天270 Deadweight Tonnage DWT (总)载重吨271 Decibel Db 分贝(噪音单位)272 Deck DK 甲板273 Deck Below 甲板下部274 Deck Block 甲板块275 Deck Composition 甲板敷料277 Deck Fittings 甲板装置278 Deck Girder 甲板梁279 Deck Longitudinal 甲板纵骨280 Deck Machinery 甲板设备281 Deck Openning 甲板开口处282 Deck Plan 甲板结构图283 Deck Plating 甲板284 Deck Store 物料间285 Deck Under 甲板下部286 Deck Water Seal 甲板水封287 Deckhouse 甲板室，上层建筑288 Deep Tank 深舱289 Defect 缺陷290 Definition 定义291 Deflection Plate 反射板292 Deformation 变形293 Degreasing 脱脂294 Dehumidifier 除湿器295 Delete 刪除, 取消296 Delivery Lead Time 交货需要时间297 Department of Trade DOT 贸易部298 Derrick Post 起重机柱299 De-rusting 去锈300 Design Load 设计载荷301 Design Load Water Line DLWL 设计满载吃水线302 Detail DET. 详细，节点303 Detail Design 详细设计304 Detailed Assembly procedure DAP 详细装配工艺305 Detector 探测器，检测机306 Deutsche Industrie Normen DIN 德国工业标准307 Deviation 偏差308 Dew Point D.P ［气，雾］露点309 Diagonal Line 对角线310 Diameter DIA 直径311 Diaphragm DIAPH. 橫膈膜312 Diesel Generator D.G 柴油发电机313 Diesel Oil DO 柴油314 Disassemble 分解315 Distribution分散316 Dock Trial 系泊试车317 Double Bevel 双斜面318 Double Bottom D/B, D.BTM 双层底319 Double Continuous Fillet Welding D.C.F.W 双面连续角焊320 Double Fillet Weld 两面填角焊321 Double Hull 双船体322 Double Skin Construction 双船体构造323 Doubling plate/Doubler D/PL. 甲板，双层板/复板324 Down-Hand welding 俯(平)焊325 Draft Gauge 压差式风压计326 Draft Marks 吃水标志327 Drain Hole D/H 排水孔328 Drain System 排水系统329 Drain Trap 放泄弯330 Dresser Coupling 带盘根套筒331 Driptray 接油(水)盘332 Dry Film Thickness DFT 干镀膜的厚度333 Drydocking 干船坞334 Duct Keel 箱子型龙骨335 Dummy 虚拟的336 Duration 为期337 Dust Collector 集尘器338 Each EA 每个，个数339 Earth Connection 接地340 Echo Sounder 回声探测仪341 Edge Welding 边缘焊接342 Effective Throat 有效喉道截面343 Efficiency 效率344 Electric Cable Pipe ECP 电缆管345 Electric Load Analysis 电器负荷分析346 Electric Resistance Welding ERW 电阻焊接347 Electro Gas Welding EGW 电气焊348Electrode Holder 电焊钳349 Electro-Hydraulic System 电动液压系统350 Electrostatic Hazard 静电危险351 Elevation ELEV. 正面图352 Elevator 升降机,电梯353 Embarkation Light 乘船灯354 Emergency Door 太平门,紧急出口355 Emergency Escape Trunk 紧急逃生通道356 Emergency Exit 太平门,紧急出口357 Emergency Fire Pump 应急消防泵358 Emergency Power Supply 应急电源359 Enclosed Space 封闭区域360 Engine Control Console 机控台361 Engine Control Room ECR 机控室362 Engine Room Arr't E/Rm Arr't 轮机舱布置图363 Engine Room Bulkhead E/R BHD 轮机室舱壁364 Ensign Staff 船尾旗杆365 Equipment List 设备目录366 Equipment Number 设备数367 Erection EREC.(E) 合拢368 Erection Schedule 合拢计划369 Even Keel 平板龙骨370 Exhaust manifold 排气集管371 Exhaust Valve 排气阀372 Expanded metal 多孔(拉制)金属网373 Expansion EXPAN , EXP. 展开374 Expansion Joint 膨胀节375 Expansion Tank 膨胀柜376 Explosion-Proof Lamp 防爆灯377 Explosive Atmosphere 爆炸危险区域378 Exposed Deck 露天甲板379 Extension Loop 伸缩弯380 Extension Rod 伸缩尺,伸长杆381 Extra Work 额外工作382 Eye Plate 眼板383 Fabrication Fab. 制作,加工384 Fabrication Shop 加工车间385 Face Flat F/F 面板386 Fairing(up) 流线型/整形387 Fairlead 导缆孔388 Fairleader 导缆孔389 False Bottom FALSE BTM. 活（假）底390 Fashion Plate FASHION PL. （钢板）组成船首材板391 Fatigue Analysis 疲劳分析392 Fender 护舷393 Fiber Glass 玻璃纤维394 Fiber Reinforced Plastics FRP "玻璃纤维增强塑料，玻璃钢"395 Fillet Welding 角焊396 Fin Stabilizer 减摇鳍397 Final Drawing 最终图纸398 Finish Paint 最后喷漆399 Finite Element Mothod FEM 有限要素法400 Fire Control Station 消防站401 Fire Damper 防火风闸402 Fire Extinguisher 灭火器403 Fire hose Box 消防水龙管箱404 Firemain Line 消防用管路405 Fit and Weld 铆焊406 Fit-up 组装407 Fix Jig 固定夹具408 Fixture 固定设备409 Flame Screen 火焰掩蔽物410 Flat Bar F.B 扁钢411 Flatness 平面度，扁平度412 Flexible Hose 软管，挠性管413 Flexible mounting 软安装414 Float Valve 浮阀415 Floating Dock 浮船坞416 Flood Light 泛光灯，探照灯417 Flooding Test 浸水试验418 Floor 肋板419 Floor Plate 地板，肋板420 Flow Chart 流程图421 Flue Gas 烟气，废气422 Flushing 冲洗423 Flux 熔剂424 Flux Cored Arc Welding FCAW 熔芯弧焊(CO2焊接) 425 Foam Fire Extinguisher 泡沫灭火器426 Foam Monitor 泡沫喷射装置427 Foot Valve 底（背压）阀/脚踩阀428 Fore Construction 船头构造图429 Fore Perpendicular F.P 艏垂线430 Forebody 船前身431 Forecastle Deck F'CLE DK 艏楼甲板432 Foremast 前桅433 Forepeak Tank 船首尖舱434 Forged Steel 锻造钢435 Forklift Truck 叉车436 Forward FWD 向船头方向437 Foundation FDN 底落438 Frame FR. 骨架，肋骨439 Frame Space F.S 肋骨间距440 Free of Charge 免费441 Free On-Board FOB 离岸价格442 Freefall Lifeboat 自由下落式救生艇443 Fuel Oil Tank 燃油舱444 Full Penetration F.P 全焊透445 Funnel 烟道446 Funnel Mark 烟道标志447 Furniture 家具448 Galley 厨房449 Galvanizing GALV. 镀锌，电镀450 Gangway 舷梯451 Gantry Crane 龙门吊，龙门起重机452 Gas Cutting 气割453 Gas Detection System 气体探测系统454 Gas Metal Arc Welding GMAW 气体金属弧焊455 Gas Tungsten Arc Welding GTAW 气体钨弧焊456 Gasket 垫圈457 Gastight Bulkhead 气密舱壁458 Gate Valve 闸阀459 general Arrangement G/A 总布置图460 General Cargo Ship 一般货船461 General Outfitting 一般舾装462 General Stock Item GSI 一般库存资材463 Girder GIR. 梁，槽钢/珩材464 Glass Reinforced Plastics GRP 玻璃钢465 Glass Wool 玻璃丝466 "Global maritime Distressand Safety System" GMDSS 全球海上遇险安全系统467 Global Positioning System GPS 全球定位系统468 Globe Valve 截止阀469 Goliath Crane 重型龙门起重机470 Gooseneck Ventilator 鹅颈式通风筒471 Gouging 气刨，表面切割472 Grade 等级473 Grand Assembly 主要装配474 Grating 格柵，柵极475 Gravity Arc Welding 重力式弧焊476 Gravity Tank (Head Tank) 重力罐477 Grease Nipple 注油嘴478 Grid 格子479 Grinding GRIND'G.(G) 打磨480 Gross Tonnage GT 总吨数481 Guard Rail 保护栏杆482 Guide Piece 定位片483 Gunwale 船舷上缘484 Gutter Bar 围板，挡板485 Gutter Pipe 排水管486 Gyrocompass 陀螺罗经487 Half Round Bar H.R.B 半圆钢488 Hand Grip H/G, HA, Ha 把手489 Handrail 栏杆490 Handysize B/C 便利B/C (5万吨以下的B/C) 491 Hatch 舱口492 Hatch Coaming 舱口拦板（边材）493 "Hatch Cover(Folding/Side Rolling/Pontoon)" "舱口盖(折叠/卷边/浮桥)"494 Hatch End Beam 舱口端梁495 Hawse pipe 锚链管496 H-Beam (H) “H”钢497 Headroom 头上空间/吊钩净高498 Heat Resistant Paint 耐热漆499 Heat Treatment 热处理500 Heating Coil 加热盘管501 Heating Torch 切割器，焊炬502 Heating Ventilation and Air Conditioning HVAC 通风及空调503 Heavy Fuel Oil HFO 重燃油504 Hexagon Head Bolt 六角头螺栓505 Hexagon Wrench 六角扳手506 High Stress Zone 高应力部位507 High Temp. Cooling Water Syestem H.T.C.W System 高温冷却水系统508 High Tensile Steel 高张力钢509 hinge 铰链510 Hogging(ref: Sagging) 弯度，挠度511 Hold 货舱512 Hold Frame 舱内肋骨513 Holding-Down Bolt 压紧螺栓514 Holiday 油漆漏掉部分515 Hopper Tank 舱底污水储藏边仓516 Horizontal HORI. 水平517 Horizontal Girder 水平梁518 Horizontal Stiffener 水平防摇材519 Horizontal(Position) Welding 水平焊接520 Hull Block Construction Method HBCM 船体分段建造法521 Hull Block Painting 整块上漆522 Hull Construction 船体构造523 Hull Form Coefficient 船型系数524 Hull Fouling 船体污损525 Hull Opening 船体开口526 Hull Outfit 船体装备527 Hull Parts List 船体附件表528 Hull Piping 船体管道系统529 Hull Preservation 船体保存530 Hull Steel 船体钢材531 Hull Strength 船体强度532 Hull Weight 船体重量533 Humidity Control 湿度控制534 Hydrant Valve 消防栓535 Hydraulic。
船舶常用英语名称外板部分TOPSIDE 干舷BOTTOM 船底SEA CHEST 海底阀箱RUDDER 舵 BOW THRUSTER 艏侧推器BILGE KEEL 舭龙骨FENDER 护舷材SHAFT TUBE 艉轴管RUDDER STOCK TRUNK 舵杆筒MANHOLE 人孔 PROPELLER NOZZLE 导流罩 DRAFT LINE 水线ANCHOR RECESS 锚穴（唇） SHELL PLATE 外板SLIPWAY 滑道BULBOUS BOW 球鼻艏SKEG 导流尾鳍CATHODIC PROTECTION SYSTEMS 阴极保护ERECTION JOINTS 合拢缝 FLAT BOTTOM 平底VERTICAL BOTTOM 直底PILOT MARK 引水员标志 DRAFT MARK 吃水标志 PROPELLER 螺旋桨SHAFT BRECKET 艉轴支架 BOSSING 包轴套CONSTRUCT SUPPORT 建设墩BOOTTOP 水线 SPARE ANCHOR 备用锚 POPPET 下水支架SHAFT DUCT 轴隧道 POUR PAINT 灌油BOAT DECK 艇甲板FORE PEAK TANK(F.P.T.) 艏尖舱AFTER PEAK TANK(A.P.T.) 艉尖舱CARGO OIL PIPE(C.O.P.) 货油管DERRICK BOOM 吊标杆SLOP TANK 污油舱VOID SPACE(VS) 空舱CARGO LEAD DAVIT 货物导架PORT(P) STARBOARD(S) CENTER(C) 左.右.中INERT GAS PIPE 惰气管WATER BALLAST PIPE(W.B.P.) 压载水管PUMP ROOM 泵舱STEERING GEAR ROOM 舵机舱RAMP WAY 坡道RAMP DOOR 艉门DECK MECHANISM 甲板机械PASS WAY 通道PASSAGE 走廊COFFER TANK 隔离舱WING TANK 边舱DUCT KEEL 管道舱BLOCK SECTION 分段FRESH WATER TANK(F.W.T.) 淡水舱DRINK WATER TANK(D.W.T.) 饮水舱DISTILLED WATER TANK(D.W.T.) 蒸馏水舱STERN ROLLER GROOVE 艉滚轮.槽SHARK PINCERS 鲨鱼钳FOAM TANK 泡沫舱BRINE TANK 盐水舱METHANOL TANK 甲醇舱BASE OIL TANK 基础油舱GREY WATER TANK 灰水舱LIQUID MUD TANK 泥浆舱DRY MUD TANK 干泥舱RIG CHAIN STORE 索具存放库RIGGING STORE 索具库AZIMUTH THRUSTER 方位推进器AIR DUCT 风道(小)HEELING WATER TANK(H.W.T.) 调倾水舱HEAVY FUEL OIL(HFO) 重燃油TOOL ROOM 工具室PAINTS STORE 油漆库GALVANIZING PIPE 镀锌管FLUME TANK 减摇舱BILGE TANK 舱底水仓CONT.BILGE TK. 控制舱底水仓TECHICAL F.W.T. 技术淡水舱VOID BOW THRUSTER 艏侧推空舱SEWAGE WATER TANK 污水舱PICKLING PIPE 酸洗管FLUSHING PIPE 串油管STOOL 壁墩USED OIL TANK 废油舱SPILLAGE TANK 接油槽BREAKWATER 挡浪板CONTAINER FITTING 紧固件CELL GUIDE 导架HATCH TRUNK 舱口围壁NAVIGATION DECK 驾驶甲板MUDGUARD 挡泥板DECK MAST HOUSE 甲板桅房HATCH COAMING 舱口围板CRANE DECK 甲板克伦吊OIL DRAIN TRAY 接油槽DANGEROUS STORE 危险品仓库CRANE POST/JIB 克伦吊柱/臂VENTILATOR(VENT.) 风道CONTAINER SOCKET 集装箱插座BULKHEAD 舱壁/围壁COFFERDAM 隔离空舱STEEL ROOM 铁制房间VENTILATOR PIPE 风道管CARGO HOLD VENT. 货舱风道HYD.PIPE 液压管MAIN DECK HATCH COVER 主甲板舱盖TWEEN DECK HATCH COVER 二甲板舱盖LADDERS 梯子SHUTTER 百叶窗SUPPLY ROOM 供应室MODIFY PIPE 修改管CARGO CONTROL ROOM 货控室CABLE SUPPORTER 电缆支架SMOKE BOX 烟箱WATERTIGHT DOOR 水密门PENETRATION PIPES 过壁短管RESIDUAL OIL TANK 残油舱机舱部分ENGINE ROOM(E/R) 机舱UPPER PLATFORM 上平台LOWER PLATFORM 下平台TANK TOP(TT) 甲底INNER BOTTOM 内底FLOOR 地板CEILING 天棚WALL 墙MAIN ENGINE(M/E) 主机GENERATOR(G/E) 发电机AUXILIARY ENGINE(A/E) 辅机EMERGENCY GENERATOR(EM.G/E) 应急发电机EL.WORK SHOP 电工工作间EL.STORE 电工仓库WORK SHOP 工作间/检修间CONTROL ROOM 控制室FIRE PUMP ROOM 消防泵仓SAFETY EQUIPMENTS STORE 安全设备库INERT GAS GENERATOR ROOM 惰性气体装备库CO 2 ROOM 二氧化碳室INCINERATOR 焚烧炉N 2 ROOM 氮气室C 2 H 2 ROOM 乙炔室PURIFIERS ROOM 净油机室BOILER 锅炉EXHAUST PIPE 排烟管EXHAUST GAS BOILER 废气锅炉STEAM PIPE 蒸汽管HOT WATER PIPE 热水管SEA PIPE 海水管FIRE PIPE 消防管DRAIN PIPR 排水管INSULATION 绝缘M/E FOUNDATION 主机座子MAIN AIR RESERVOIR 主空气瓶UTILITY AIR RESERVOIR 杂用空气瓶AUX.AIR RESERVOIR 付空气瓶CONTROL AIR RESERVOIR 控制空气瓶BILGE WATER TANK 污水井/舱底水仓HOT WELL 热井F.W.HYDROPH TANK 淡水压力罐D.W.HYDROPH TANK 饮水压力罐FREEZING PIPE 冷冻管DIESEL OIL TANK(.) 柴油柜D.O.STORAGE TK. 柴油储存柜D.O.SERVICE TK. 柴油日用柜D.O.SETTLE TK. 柴油沉淀柜BOILER . 锅炉柴油柜INCINERATOR . 焚烧炉柴油柜EM.G/E .(EMERGENCY) 应急发电机柴油柜D.O.OVERFLOW ALARM TK. 柴油溢流报警柜HYDRAULIC PRESSURE 液压HYD.OTK. 液压油柜HYD.ODRAIN TK. 液压油泄放柜STEERING GEAR . 舵机液压油柜CYLINDER OIL TANK 汽缸油柜CYL.O.DRAIN TK. 汽缸油泄放柜CYL.O.MEASURE TK. 汽缸油计量柜CYL.OSTOR TK. 汽缸油储存柜TURBINE OIL TANK(.) 透平油柜BOILER . 炉水舱HIGH TEMPERATURE(H.T.) 高温LOW TEMPERATURE(L.T.) 低温F.W.EXPAND TK. 淡水膨胀箱INSP.FILTER TANK 检油箱COOLING . 冷却水舱GJP UNIT 填料函油柜NOZZLE COOLING . 油头 ( 喷油嘴 ) 冷却油柜SCAVENGE AIR BOX DRAIN TK. 扫气箱泄放柜AIR COOLER CLEAN TK. 空冷气清洁柜OPERAT WATER TK.FOR D.O.PUR 柴油净油机工作箱BOILER CONDENSATION . 锅炉冷凝水箱CJC FILTER UNIT CJC 单元COMPRESSOR 空压机CAM SHAFT 凸轮轴STERN TUBE(S/T) 艉轴ECHD SOUND AND LOG TK. 测深计程义仓E/R BILGE TK. 机舱舱底水仓GEAR BOX 齿轮箱SLUDGE TK. 油渣柜SOIL TK. 污泥或粪便柜DISTRIBUTOR ROOM 配电盘室SWITCH BOARD ROOM 开关板室STAIRSWAY 梯道GRATING 花壁FLOWER FLOOR 花地板FUEL OIL TANK（F。
船舶专业英语词汇1, steering ['sti?ri?]n. 操纵；指导；掌舵v. 驾驶；掌舵（steer的ing形式）2, gear [ɡi?]n. 齿轮；装置，工具；传动装置vi. 适合；搭上齿轮；开始工作vt. 开动；搭上齿轮；使……适合；使……准备好adj. 好极了3, refrigeration [ri,frid??'rei??n, ri:-]n. 制冷；冷藏；[热] 冷却4, provision [pr?u'vi??n]n. 规定；条款；准备；[经] 供应品vt. 供给…食物及必需品5, store [st?:]n. 商店；储备，贮藏；仓库vt. 贮藏，储存6, tally ['t?li]n. 计数器；标签；记账vt. 使符合；计算；记录vi. 一致；记分7, changing ['t?eind?i?]v. 改变（change的ing形式）；交换；兑换n. 改变；转换；替换adj. 变化的；发展的8, gym [d?im]n. 健身房；体育；体育馆9, electric [i'lektrik]adj. 电的；电动的；发电的；导电的；令人震惊的n. 电；电气车辆；带电体10, channel ['t??n?l]vt. 引导，开导；形成河道n. 通道；频道；海峡11, pipe joint管接；导管接头12, pipe [paip]n. 管；烟斗；笛vi. 吹笛；尖叫vt. 用管道输送；尖声唱；用管乐器演奏13, laundry ['l?:ndri, 'lɑ:n-]n. 洗衣店，洗衣房；要洗的衣服；洗熨；洗好的衣服14, sanitary ['s?nit?ri]adj. 卫生的，清洁的n. 公共厕所15, case [keis]n. 情况；实例；箱vt. 包围；把…装于容器中16, etcadv. 等等，及其他17, accommodation [?,k?m?'dei??n]n. 住处，膳宿；调节；和解；预订铺位18, forepeak ['f?:pi:k]n. 船首舱19, airconabbr. 空调（Air conditioning）20, galley ['ɡ?li]n. [船] 船上的厨房；单层甲板的大帆船；活版盘，长条校样21, mess [mes]n. 混乱；食堂，伙食团；困境；脏乱的东西vt. 弄乱，弄脏；毁坏；使就餐vi. 把事情弄糟；制造脏乱；玩弄22, toilet ['t?ilit]n. 厕所，盥洗室；梳妆，打扮vi. 梳妆，打扮vt. 给…梳妆打扮23, stair [stε?]n. 楼梯，阶梯；梯级24, crew [kru:]n. 队，组；全体人员，全体船员vi. 一起工作vt. 使当船员25, conference room会议室，会议厅26, conferencen. 会议；协商；讨论；[篮]联盟27, captain ['k?ptin]n. 队长，首领；船长；上尉；海军上校vt. 指挥；率领28, chief engineer[劳经] 总工程师；轮机长；主任工程师；总技师29, pilot ['pail?t]n. 飞行员；领航员adj. 试点的v. 驾驶；领航；试用30, charging ['t?ɑ:d?i?]n. 炉料；装料v. 使承担（任务等）；装载；命令（charge的现在分词）31, discharge [dis't?ɑ:d?, 'dist?ɑ:d?, dis't?-]vt. 解雇；卸下；放出；免除vi. 排放；卸货；流出n. 排放；卸货；解雇32, radar ['reid?]n. [雷达] 雷达，无线电探测器33, mast [mɑ:st, m?st]n.桅杆；柱；橡树果实vt. 在…上装桅杆34, communication [k?,mju:ni'kei??n]n. 通讯，[通信] 通信；交流35, signal ['siɡn?l]n. 信号；暗号；导火线vt. 标志；用信号通知adj. 显著的；作为信号的vi. 发信号36, recorded [ri'k?:did]adj. 记录的v. 记录；录音（record的过去分词）37, general arrangement总布置38, reliale39, assessed [?'sest]v. 对…进行评估（assess过去时形式）40, maintainedadj. 被保持的v. 维护，维修；维持（maintain的过去分词）41, yacht [j?t]vi. 乘游艇，驾游艇n. 游艇，快艇；轻舟42, overhaul [,?uv?'h?:l, '?uv?h?:l]vt. 分解检查，大修；追上并超过n. 彻底检修，详细检查43, maintenance ['meint?n?ns]n. 维护，维修；保持；生活费用44, extremesn. 狂热分子，极端条件45, encounter [in'kaunt?]vt. 遭遇，邂逅；遇到n. 遭遇，偶然碰见vi. 遭遇；偶然相遇46, encountered [in'kaunt?d]v. 遇到；曾遭遇（encounter的过去式）47, toll [t?ul, t?l]损失。
船舶英语1.“MT”motor tanker船舶2.“MV”motor vessel 船舶3.Shore 岸边4.Wharf码头5.Berth泊位6.Portside左舷7.Starboard右舷8.Manifold接口9.Captain/master 船长10.Chief officer 大副11.Second officer 二副12.Bosun 商船甲板长13.Loading master 岸方主管14.Bow船头15.Stern船尾16.Pipeline 管线17.Hose 软管18.Valve阀门19.Pump room 泵房20.Derrick起重机21.Crane吊车22.Hammer榔头23.Spanner扳手24.Ring spanner梅花扳手25.Box spanner 套筒扳手26.Life boat 救生艇27.Life raft救生筏28.Life buoy 救生圈29.Air 空气pressed air压缩空气31.Air blow 吹管32.Temperature 温度33.Pressure 压力34.Steam蒸汽35.Heating加热36.Leakage 漏、渗37.Sampling 取样38.Samper样品39.Tank capacity舱容40.Ship draft 吃水深度41.Draft forward 前吃水42.Draft middle 中吃水43.Draft after后吃水44.Bill of loading（BL）提单45.Tank inspection certificate 舱检证书46.Dry Tank inspection certificate干舱证明47.AfterTank inspection certificate湿舱证明48.Time sheet 时间表49.All fast 靠泊时间50.Densit chart密度表51.Ullgae report空尺报告52.sounding report实尺报告53.Voyage temperature record 全程加温记录54.Refining精炼55.Bleaching脱色56.Deodorization脱臭57.Plam oil棕榈油58.Plam olein棕榈液油59.Plam stearin 棕榈硬脂。
For personal use only in study and research; not for commercial use 一、常用词汇船长captain大副chief officer二副second officer三副third officer代理ship’s agents引水员pilot码头调度loading master 前缆fore/ head lines后缆back/ stern lines围油缆oil boom带紧缆绳fasten lines松些缆绳slack lines引缆heave lines绞缆机mooring machine 螺丝screw垫片gasket法兰flange扳手wrench吊机crane/ derrick梯子ladder防护网protection net盲板blind fold大小头pipe line reducer 回气管vapor return line 蒸汽管steam line热水warm water管道pipe 接管connect line拆管disconnect line接管时间time of line connecting拆管时间time of line disconnecting装货load cargo卸货discharge cargo结束时间time of completion discharge 离泊时间sailing time氮气nitrogen空气fresh air加压increase pressure减压decrease pressure吹扫purge/ air purge扫舱clean the tanks扫线clean the lines验空舱empty tank survey取样take sample品质化验quality analysis商检cargo survey拖轮tug boats冻住frozen堵住stuck接地线earth/ ground line船舶资料ship particulars配载图stowage plan保安声明safety/ security warrant二、常用句型现在几点What time is it now?大概几点It’s about … o’clock.我想见大副，在哪能找到他？I want to see Chief Officer, where can I find him? 现在是退潮The tide is falling.现在是涨潮The tide is rising.现在是平潮The tide slacks.现在检查Check right now.等一下Wait a minute.船向前/向后移动2米Move 2 meters forward/ backward.准备好了Everything is ready./ Ready now.阀门已开Valve is open.送出前/后缆Send out head/ stern lines.你们几点开工？What time are you going to start working?你们什么时候完工？When will you finish working?多长时间卸完（装完）？How long will it take to finish discharging (loading)? 准备好装卸货了吗？Are you ready to load/ discharge?可以卸货You may start discharging.慢一点卸货Slower down discharge speed.立即停止卸货Stop discharging immediately.最大装/卸货速度是多少？What is the maximum loading/ discharging rate? 请固定好Please fasten/ fix it.请问现在压力多少？What is the pressure right now?在下面放个垫子Put a pad underneath.别让小船靠过来Don't allow river boats to get alongside your ship.商检明天来Cargo surveyor is coming tomorrow.商检回办公室/家了Cargo surveyor returns office/ home.再吹扫一次One more purge.请把软管放下一点Lower down flexible hose.开始（慢）泵Start pumping (slowly).停泵Stop pumping.现在就加热Heat right now.请把舱盖都打开Open all cargo holds hatch covers.先循环后再取样Take samples after cargo internal circulation.上一港是哪里What is your last port?温度太高/低The temperature is too high/ low.这票货需要供氮气The shipment needs to supply nitrogen.这票货结束要洗舱The shipment needs tank wash.我们可以接上输油臂吗？Can we connect loading arms?输油软管5分钟后接好Cargo hoses will connect in 5 minutes.三、实用句子1. 调度室通知，你船明天早上八点开船。
船舶英语词汇大全一、船舶基本结构词汇1. 船体（Hull）：船舶的主体部分，包括船壳、甲板和舾装。
2. 船壳（Shell）：船体的外表面，起到防水、承重的作用。
3. 甲板（Deck）：船舶的顶部平面，用于行走、作业和装载货物。
4. 舷窗（Porthole）：船体两侧的窗户，用于通风和采光。
5. 舷梯（Jacob's ladder）：连接船舶与码头的小梯子，便于人员上下船。
6. 舵（Rudder）：控制船舶方向的装置，位于船尾。
7. 锚（Anchor）：固定船舶位置的器具，用于抛锚停泊。
8. 船锚链（Anchor chain）：连接船锚与船舶的链条。
9. 船舶龙骨（Keel）：船体底部的一条纵向构件，起到支撑作用。
二、船舶动力装置词汇1. 船舶主机（Main engine）：船舶的动力源，通常为柴油机或蒸汽轮机。
2. 船舶辅机（Auxiliary engine）：为船舶提供辅助动力的装置，如发电机、空压机等。
3. 螺旋桨（Propeller）：将主机产生的动力转化为推力的装置，位于船尾。
4. 柴油机（Diesel engine）：以柴油为燃料的内燃机，广泛应用于船舶动力装置。
5. 蒸汽轮机（Steam turbine）：利用蒸汽驱动叶轮做功的热力发动机。
6. 燃油喷射泵（Fuel injection pump）：柴油机燃油系统中，将燃油高压喷射到燃烧室的装置。
三、船舶导航设备词汇1. 罗经（Compass）：指示船舶航向的导航仪器。
2. 船用雷达（Marine radar）：用于探测船舶周围水域障碍物的电子设备。
3. GPS导航仪（GPS navigator）：全球定位系统导航设备，用于确定船舶位置和航迹。
4. 电子海图（Electronic chart）：显示海域地理信息的电子地图。
5. 船舶自动识别系统（S）：用于船舶识别、追踪和避碰的通信系统。
四、船舶通讯设备词汇1. 船用无线电（Marine radio）：用于船舶与船舶、船舶与陆地之间通信的无线电设备。
2.Next time, we’ll be fully ready for the inspection. 2. 下一次，我们会为检查做好充分准备。
9. Explaining the details of work 9. 工作细节解释1. I think something’s missing in the draw ing. 1. 我想图纸上漏了些东西。
2. Check it with the drawing. 2. 根据图纸检查。
3. The main work will be finished at 4 today. 3. 主要工作4天内完成。
4. Another of the owner’s surveyors has already inspection it. 4. 另一个船东检查员已经检查了。
5. I did it as the drawing says. There’s nothing wrong. 5. 我根据图纸工作的，没有错。
6. If you have any problems. I’ll confirm them to the design department.如果你还有问题的话，我会通知设计部。
7. Yesterday, we did a preliminary inspection for this test. 7. 昨天，我们做了测试的初步检查。
8. Let me cover it with plastic because rain is dripping off the scaffold.让我们用塑料把它盖起来，因为雨从脚手架上滴下来了。
9. Though it’s raining, The inside of the paint shop looks all right.尽管下雨，涂装工厂里面看起来不错。
10. I don’t think it’s a big mistake. 10. 我不认为这是很大的错误。
11. We touch up the roughly-welded lines with a roller / a brush.我们用滚筒或刷子粗略地画出焊接线。
12. I want you to confirm the result of the inspection. 12. 我想你来确认检查结果。
13. If you apply heat on the curve. You will not maintain it because of contraction.如果你申请曲面上加热，由于结果原因可能无法保持它。
14. The painting of Block GB12 doesn’t meet the thickness requirements in the specifications.GB12分段的涂装没有符合说明书上的厚度要求。
15. It doesn’t matter at all in terms of technical asp ects. 15. 根据技术上，一点问题也没有。
16. We touched it up this morning so some part are still wet. 16. 我们今天早上已经擦过了，一些地方仍潮湿。
17. This is a unique case which can be caused by the characteristics of the machine.这是一个特别的例子，可能是由于机器特征引起的。
18. It looks all right in terms of the machine. 18. 按照机器来说，它看起来不错。
19. The surface is painted sufficiently. 19. 表面涂装充分。
20. We’ve touched up the back of the longitudinal twice with a r oller.我们用滚筒涂纵向背面两次。
21. When repairing leaks, we always release the air out of the tank before rewelding it.当修补漏洞时，我们通常在重焊前把空气排出舱外。
22. This is an unexpected case. 20. 这是个意想不到的例子。
23. Supporting areas are reserved to b e painted later. Let’s begin at the P.E &DOCK STAGE.支撑部位应后涂装，我们从P.E &DOCK STAGE开始吧。
24. The vacuum test was done before, and I couldn’t find any faults.真空试验以前做过，我没有发现缺点。
25. It may look severely deformed, but if checked, it is within the accepted tolerance.它可能看前来严重变形，但是如果修正，还是可以接受的。
26. While moving the block , we damaged it. 26. 当运送分段时，我们破坏了它。
27. We do a masking job on unpainted part before painting. 27. 我们在未涂装部位做了28. It’ll take a lot of time to do it due to the previous error. 28. 由于先前的错误，花了很多时间做它。
29. We followed the design exactly. 29. 我们严密地根据设计。
30. According to the specifications. The grade of this part is St3.根据说明书，这个部位的等级是St3。
31. If we do not do this painting job immediately, the plate will rust quickly in the weather like this.如果我们没有马上做涂装工作，板在这种天气下很快就会生锈。
32. The deformation tolerance of the side shells is ±6mm. 32. 外板的变形量为±6mm。
33. Please wipe off the welding slag. 33. 请擦去焊渣。
34. Our construction manual says to do it like this. 34. 我们的建造手册说是这样做的。
35. Our standard is~. 35. 我们的标准是~36. Since this part is different from the drawing, we will let you know the design department’s opinion after we consult with them. 36. 由于这部分跟图纸不一样，我们会跟设计部分讨论后告诉你。
37. This part is different from the design. 37. 由于这部分跟设计不一样。
38. This part has been done in this way/manner. 38. 这个部位应按这样方法做。
39. It’s the right material according to the drawin g. 39. 这是根据图纸的正确的材料。
40. Five people are working on this block. 40. 5个人在这个分段上作业。
41. The work on this block was conducted in the Assembly Shop. 41. 这个分段上的工作在装配工厂处理。
42. The surface preparation grade of this block of this block is St3, Sa25.这个分段的表面准备登记是St3, Sa25。
43. This job will take about 3 days. 43. 这个工作需花3天时间。
44. This equipment is imported, so it’s impossible to modify. 44. 这种设备很重要，所以不可能修改。
45. This is within an acceptable range(tolera nce) of error, so it’s OK.这是可以接受的错误，所以没问题。
46. It’s all right to this extent. 46. 这宽度没问题。
47. This is not leaked water, but condensation. 47. 这不是漏水，是浓缩。
48. This is the item which was approved during the previous process.这个项目由以前的过程证明的。
49. This is the part we changed in accordance with (according to)the new drawing.(This has been changed according to the new drawing) 49. 我们改变的部位根据新图纸50. I have confirmed that there are no-mistakes(errors) 50. 我已经确认没有错误。
51. We are still waiting for the material to arrive. 51. 我们还在等材料的到来。
52. I’ll instruct my workers not to make same mistakes. 52. 我会教育工人不能在范同样的错。
53. In my opinion, there will be no problem doing it this way. 53. 依我看来，这样做没问题的。
54. I’ll show you the de sign. 54. 我给你看设计。
55. The modification you mentioned is within an acceptable range of SSQS.你提到的修改是在SSQS可以接受的范围内。
